Hamilton Beach 1G901 Blender User Manual
Contents
1. 840111501 EN Hamilton Beach CcoMmMpM Oe AL Bar Blenders Models 10001 10908 10909 10910 10918 16919 Operation Manual www commercial hamiltonbeach com Blender Safety IMPORTANT This operation manual should be reviewed with all equipment operators as part of your operator training program Your safety and the safety of others is very important We have provided many important safety messages in this manual and on your appliance Always read and obey all safety messages This is the safety alert symbol This symbol alerts you to hazards that can kill or hurt you and others All safety messages will be preceded by the safety alert symbol and the word DANGER or WARNING These words mean You will be killed or seriously injured if Ne ER you don t follow instructions You can be killed or seriously injured if AWARN l NG you don t follow instructions All safety messages will identify the hazard tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed AWARNING AWARNING E Electrical Shock Hazard Plug into a grounded outlet Do not remove ground Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock Cut Hazard Always place cover on jar when blending Do not put hands spoons or other utensils in jar when blending Failure to follow these ins2. General Cleaning Fill container with sanitizing solution See Recommended Sanitizing Solution below and place on base Replace cover and filler cap and run on LOW except model 1G901 speed for 2 minutes Empty container Wipe the container exterior with a soft cloth or sponge dampened with sanitizing solution Immerse the cover and filler cap in sanitizing solution for two minutes Remove any remaining moisture from cutter assembly by replacing container on base with cover and filler cap in place Then run blender on HiGH except model 1G901 speed for a minimum of 2 minutes To dry place empty container on base and run on HIGH except model 1G901 speed for two sec onds When ready to use rinse with clean water NOTE Do not rinse container cover or filler cap after sanitizing Recommended Sanitizing Solution The sanitizing solution should consist of 1 tablespoon of household bleach per 1 gallon of clean cool water 60 F 16 C mixed according to the instructions on the bleach When using a sanitizing solution other than that recommended the sanitizing solution concentration should be tested using commercially available test strips and should indicate a concentration between 100 and 200 parts per million of bleach to water Troubleshooting Guide Problem Blender fails to start Check to see if unit is securely plugged into an electric outlet or stops whil
3. container Models 7 Set the Hi Low switch except model 1G901 to 1G910 1G918 1G919 the desired speed See Professional Blending Techniques for blending tips NOTE If you want the blender to run for short bursts press the Pulse switch on some models While you are pressing the Pulse switch the blender will run at the selected speed Release the Pulse switch to stop the blender frrinon Beas ON OFF Pulse EE Switch HIGH LOW Switch Q faan LOW Operating the Blender Professional Blending Techniques Filling the container When filling the container with ingredients follow these recommendations Use sufficient amount of liquid to ensure that the mixture is fluid and free running at all times Pour the liquid into the container FIRST Cut solid ingredients into pieces that are no bigger than a 1 25cm cube Add the ingredients to container in batches Do not blend maximum volume all at once Do NOT overfill the container with product This may prevent the blender from processing the product properly Process dense foods or thick mixtures in small batches and remember that the volume of the product normally increases during processing Do not exceed one quart of content when blending hot product Always place the cover and filler cap on the container when blending For blending hot liquids remove filler cap from container cover before blending Blending techniques Icy drinks Do not use blender
4. to crush large ice cubes The blender is not designed for this Small ice cubes or crushed ice is recommended Pour in liquid then add ice Cover Set speed at HIGH except model 1G901 and process until desired consistency is reached Chunks of frozen fruit can be added to milk or fruit juice to produce a sherbet or slush AWARNING EA ERAS Burn Hazard Always use caution when blending hot contents Failure to follow these instructions can result in burns Blending hot mixtures IMPORTANT To minimize the possibility of scalding the following precautions MUST be observed Do not exceed 1 quart of content when blending hot product Remember that the volume of the product normally increases during processing Always place the cover on the container and remove the filler cap from container cover when blending hot liquids to prevent the build up of pressure Never stand with your face directly over the container when operating the blender where steam may be released Begin on LOW speed and then select a speed that produces a column of air in the center of the container Filler Cap Use the filler cap to add liquids to the container while the unit is running aring for the Blender Cleaning Instructions AWARNING E Electrical Shock Hazard Plug into a grounded outlet Do not remove ground Do not use an adapter Do not use an extension cord Do not immerse base in water or other liquid Failure
5. to follow these instructions can result in death fire or electrical shock General cleaning Do not allow food residue to dry on any part of the blender Wash and rinse container cutter unit assembly and base after each use or whenever it will not be used again within one hour as follows 1 Remove the container from the base and then remove the cover Add cleaning solution to the container Use a washing solution of hot water less than 115 F 46 C and a non sudsing detergent Use the recommended amount of detergent 2 Scrub and flush out the container interior cover and filler cap to remove food residue Empty container Fill container full with fresh washing solution and place it on the base Replace the cover on the container and run the blender on high speed except model 1G901 for 2 minutes Repeat step 3 using clean rinse water 95 F 35 C Wipe down the container filler cap and cover with a soft cloth or sponge dampened with fresh washing solution Wipe the exterior of the base with a damp cloth or sponge The base contains electrical components do not immerse use a high pressure washer or use a dishwasher to clean the base AWARNING Cut Hazard Always place cover on jar when blending Do not put hands spoons or other utensils in jar when blending Failure to follow these instructions can result in broken bones or cuts Sanitizing 8 Wash container as instructed in
6. water or any other liquid e Close supervision is necessary when any appliance is used by or near children e The use of accessory attachments not recom mended by Hamilton Beach may cause injuries e To reduce risk of personal injury unplug cord from outlet when not in use and before putting on or taking off parts or doing any other servicing of the blender e Do not let cord hang over edge of table or counter or touch hot surfaces e Do not place on or near a hot gas or electric burner or in a heated oven e To reduce risk of personal injury and to prevent damage to blender or jar and cutter assembly DO NOT insert utensils into blender jar while operating blender or store utensils in the blender jar when it is not in use e Avoid contacting moving parts e Blades are sharp Handle carefully e Inspect jar and cutter assembly daily Check cutter for wear nicks or broken blades Replace jar and cutter assembly at least every 12 months e Do not defeat the jar pad sensors e Do not use outdoors e This appliance is intended for short periods of operation with a rated operating time of 3 minutes e To prevent damage to blender jar or cutter assembly DO NOT move or shake blender while in operation If blending action stops during operation turn blender OFF remove jar from base remove jar cover and use a thin rubber spatula to push mixture towards cutters Do not spray the base with a high pressure spray gun Disco
7. e it is Check to see if the fuse for the electric outlet has blown or if a running and cannot circuit breaker has tripped be restarted Ingredients will not mix Check to see if enough liquid has been added to the ingredients Mixture should properly be fluid and free running at all times Solid pieces are too large Pieces should not exceed 1 2 5 cm cubes Container is too full Do not fill past highest graduation marking Cutter unit blades are not sharp or are damaged Inspect container and cutter assembly daily Replace container and cutter assembly at least every 12 months or sooner if cutter assembly appears worn or damaged Check to see if cutter unit assembly is installed properly Select speed on some models to create a fluid blend Maintenance Inspect the blender and its various parts and replace as follows Unplug the blender and remove the container from the base and then inspect the container and cutter unit assembly for wear nicks and broken or loose blades Replace if necessary If the cutter assembly blades are loose discontinue use immediately and replace the cutter assembly Do not attempt to repair or tighten the cutter assembly See Replacement Parts below Weekly Unplug the blender and then inspect the power cord insulation and power plug for cracks Refer to Requesting Assistance or Service for repair or replacement Replace the container and cutter unit assembly at least o
8. ecise blending requirements The ON OFF switch will turn the blender ON for continuous operation or OFF The HIGH LOW switch allows you to select the following speeds Hi 17 800 RPM Low 11 500 RPM The Pulse switch Models 1G910 1G918 and 1G919 turns on the blender only when the switch is pressed When the switch is released the blender will stop This will allow you to pre cisely control the operation of the blender Using the blender Before you use the blender for the first time wash the container cover and cutter unit assembly Refer to Cleaning the Blender Do not put the cutter unit assembly in the dishwasher To operate the blender proceed as follows 1 Place the blender on a clean dry level surface and set the ON OFF switch to OFF 2 Place cutter unit in the threaded collar blades up Slip the gasket OVER the blades and onto the base of the cutter unit Screw the completed blade assembly onto the container AWARNING Cut Hazard Always place cover on jar when blending Do not put hands spoons or other utensils in jar when blending Failure to follow these instructions can result in broken bones or cuts ON OFF Switch ON OFF Switch Model 1G901 3 Plug the blender into an electric outlet 4 Place the ingredients to be blended into container 5 Place the container onto the base Make sure it rests securely on the base 6 Place the cover and filler cap on the
9. he controls to your praterenoa 5 Move the power switch to the on or I position Parts and Features The parts and features for the 1G901 1G908 1G909 1G910 1G918 1G919 Blenders are shown on this page Become familiar with all parts and features before using your blender Your blender is designed for blending and mixing beverages Note The Blender is not designed to crush ice Ice cubes made in most icemakers may be added to liquid ingredients in the blender to make daiquiris or similar drinks Removable Cutter Unit Assembly Filler Cap Cover Gasket Blades ___ Clutch ______ ULA Ca Container Blender Model 1G901 On Off Models Pane Switch A 1G908 1G909 va On Off Models SI Switch 1G910 1G918 1G919 On Off Pulse Switch HIGH LOW TE Switch gt Af 4 w Q en Model 1G901 Model 1G908 Model 1G909 Model 1G910 Model 1G918 Model 1G919 Operation Operating the Blender AWARNING E Electrical Shock Hazard Plug into a grounded outlet Do not remove ground Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock Controls Model 1G901 The ON OFF switch will turn the blender ON for continuous operation at approximately 18 000 RPM or OFF Models 1G908 1G909 1G910 1G918 1G919 Two separate switches on the front panel allow you to control the blender for pr
10. nce a year See Replacement Parts below Replacement Parts Refer to Requesting Assistance or Service to order parts below Model Part Description Part Number 1G901 1 container 6126 901 1G908 1 container 6126 908 1G909 1 container 6126 909 1G910 1 container 6126 910 1G918 1 container 98000 1G919 1 container 98100 ALL Cutter unit assembly 99100 Hamilton Beach c e M M E R C I A L 261 Yadkin Road 840111501 EN Southern Pines NC 28387 05 03
11. nnect power before cleaning or servicing To prevent burns from hot liquids splashing out of the jar always remove the filler cap of the container cover before blending hot liquids Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any manner Return appliance to the nearest service facility for examination repair or electrical or mechanical adjustment If the supply cord of this appliance is damaged it must be replaced by the manufacturer or its ser vice agent or a similar qualified person If fitted with a non rewirable U K plug the 13 amp fuse approved by ASTA to be B S 1362 must be used If you need a replacement fuse carrier it must be replaced by the same colour coded carrier with the same markings Fuse covers and carriers can be obtained from approved service agents IMPORTANT If the molded plug is cut off dispose of it immediately The plug is not rewirable and would cause a shock hazard if inserted into a socket For a complete operation manual in this language please visit our website at www commercial hamiltonbeach com or call 910 692 2223 SAVE THESE INSTRUCTIONS Blender neration Quick Start Guide Place the blender on a dry level surface Make sure the power switch is in the off or O position Plug the blender into a grounded electrical outlet Place the jar on the base with ingredients and jar lid in place a 4 Set t
12. tructions can result in broken bones or cuts Requesting Assistance or Service Before calling for assistance or service please check the Troubleshooting Guide in this manual If you still need help follow the instructions below Whenever you call to request assistance or service you need to know the complete model number You can find this information on the label on the bottom of your blender Please also record the purchase date of your equipment and your dealer s name address and telephone number Model Number Purchase Date Dealer Name Dealer Address Dealer Phone You can also order replacement parts by calling your nearest Hamilton Beach Commercial Service Center or your local dealer Call our Technical Service number 866 285 1087 or 910 692 2223 8 a m 5 30 p m EST Monday Thursday 8 a m 5 15 p m EST Friday www commercial hamiltonbeach com Blender Safety IMPORTANT SAFETY INSTRUCTIONS WARNING When using electrical appliances basic safety precautions should be followed including the following e Read all instructions e Plug into a grounded outlet e Do not touch surfaces that may be hot Use handles or knobs provided e Extreme caution must be used when moving an appliance containing hot oil or other hot liquids e Do not use appliance for other than intended use e To protect against electrical shock do not immerse cord plug or blender base in
Download Pdf Manuals
Related Search