Haier HWM50-10B Washer/Dryer User Manual
Contents
1. Top lidA Water valve Water absorption Notice label cushion Detergent box Hanging hole for the drain hose Handle Adjustable foot stick Drain hose Back cover Adjustable foot Fixed foot 3 Meaning and description of the symbols Warning sign Contents marked with that symbol are related to the sate of the product and the personal safety of the users Please operate in strict conformity to the contents otherwise it may cause damage of the machine or injure the personal safety of the user Forbidden sign Contents marked with that symbol are actions forbidden to perform Performing of those actions may result in damage of the machine or injure the personal safety of the user we Safety precautions Please plug the plug on special receptacle with rated voltage Be sure to use single phase three pins receptacle Ensure the earthing prong of the power receptacle is earthed reliably Use leakage protector if possible The power cord plug should be convenient to be pluged in or pluged out with hand while the washing machine runs normally Be sure to pull the plug out and close the water tap when the machine is idle when moving the machine or when cleaning the machine Do not use wet hand to insert or pull out the power plug wipe with dry cloth carefully mS Do not damage the power cord bend extend twist bind or alter it by force Do no2. 1MPa Water inlet pressure Rated washing spinning capacity 5 0kg 5 0kg MADE IN CHINA 16
3. per indicated Drain hose in Figure 6 bushing Drain hose Take off bushing claw Figures Figure 6 Usage of the drain hose The drain hose shall drain smoothly 1 The height of the drain hose shall be less than 10cm or the drainage will not be smooth and cost such long time that the machine may stop at mid way 2 Do not trample or press the drain hose 4 lf extra drain hose is needed please make separate purchase The inner diameter of the extra hose shall not less than 30mm and the length shall not exceed 1 5m aD 5 If the extrahose is toolong cut it either atA orat B point 3 If the drain hose is too long cut it at mid point To make smooth drainage cut the front end of the hose slantingly G Co EA E Install the water inlet hose a Confirm the water tap y Water tap not suitable Water tap suitable Outlet end surface It is requiredthat the frontend shall belonger than 10mm The outlet end surface of thetap shall beflat and smooth If not please file it to ee leakage RY Connection between the water inlet hose jointer and the water tap 1 Press the lower end of the lock lever and push down the slider Take off the water inlet hose jointer from the water inlet hose component See to Figure 1 2 Loosen the screw till the water tap can be accessed Put the jointer of the water inlet hose on the tap See to Figure 2 If the tap diameter is too l
4. reserved wash program will be automatically set inactive If you desire a wash cycle to endat a reservedtime you can press the PROGRAM RESERVATION button over 2seconds to seta reserved wash program Refer to The button of PROGRAM RESERVATION on page 10 e Confirm the reserve program Page 10 La 8 e When Reservation becomes active thenixie tube displays the time to the endof the reservedwash cycle and the indicator turnson During reserve procedure push the Reservation button to display the reserve mode Tochange the running program or cancel the reservation you should cutoff the supplyand reselect 5 Press the start pause button A Close the top lid During running if the top cover is opened the washing machine will stop running and alarm Finish washing The washing machine cuts off the power supply automatically when wash cycle ends lS Disposal after washing After using please clean the lint and foreign materials of the lint filter etc in time Otherwise it may influence your using the machine Please first pull off the power plug from the receptacle before cleaning e When washing lint filter must be used e After using please clean it in time Lint filter 1 Pull upward to detach 2 Clean the lint wN Put it in water and clean while it is still wet AA See to Figure 1 Dismantle Install 3 Press downward to assemble Figure 2 The filter screen ofthe wat
5. separately from other laundries The pulsator will not rotate unless the water is filled to selected water level Selection method of the procedure programs Times of pushing Selected Applicabl d Contents tthe nixie tube indicates the select button 9C SCtea program ppilcable procedure the programs about to run 0 STANDARD Normal wash Wash bb Rinse cc Spin dd Large thick or heavily soiled Soak AA Wash bb 1 JEANS isandry Rinse CC Spin dd The laundry needn tspin to A 2 GENTLE avoid wrinkles Wash bb Rinse cc Spin dd 3 QUICK WASH For load below 1 kg Wash bb Rinse cc Spin dd 4 WASH Repeat using thewashing Wash bb liquid When the laundries need only 5 SPIN spinning after manua Spin dd washing first drainthen spin e If you pushthe PROGRAM RESERVATION button for6 times it will resume the originalmode and itwill circulate like that f you selectthe QUICK WASH program you haveto set the full procedure of wash rinseand spin The procedure cannot be selected 12 3 Press the WATER LEVEL button to select suitable water level WATER LEVEL After switching on the power press the button WATER LEVEL to select a water level according to the load Please refer to the button Water level on page 10 4 Push the PROGRAM RESERVATION button to select suitable reserve program PROGRAM RESERVATION After switching on the washing machine
6. Check the connection between the jointer of the water inlet hose and the water tap 1 Swaying the hose gently to confirmif it isfastened stable 2 After installation openthe tap tocheck if itleaks 3 Do not bendthe hose with overstrain 4 Before each usage please check if the connection betweenthe jointer of the waterinlet hose andthe water tap and theinstallation of the water inlet hoseare firm soas to prevent dropping fromimproper Installation position Takedown the water inlet hose 1 Close the watertap 2 Press the lockinglever Pushdown the slider Then pull off the water inlethose If the machine is used more than onceevery week thejointer of the water inlet hose canbe kept onthe tap toprevent damaging the fixing screw Preparation before washing Preparation before washing 1 Connect the water inlet hose and open the water tap 2 Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle Do not connect the earth ter minal to the gas pipe and tap water pipe 3 Put down the drain hose 4 Slanting or uneven ground may result in unstable working or abnormal noise Please make the machine stand horizontally Pay attention to followings before washing the laundries Confirm if Clear the pocket Fasten the The quantity of When the pulsator there s special Take out the buttons and the laundries is running the requirement f
7. ER ON OFF to connect power supply if the washing machine lasts idle more than 5 min it would automatically shut off the supply 10 b Operating procedure and explanations for the buttons PROGRAM STATUS PROCEDURE STATUS E FUZZY O HIGH SURPLUS MIN TE END W SOAK O wevi g oe JEANS bb WASH oO ion E pe 3 GENTLE cc RINSE oO renin 4 QUICK WASH ag SPIN 6 WASH f POWER 06 SPIN START ONOFF PROGRAM PAUSE E K 1 Press the POWER ON OFF button to switch on the power supply OWER ON OFF 2 Press the button of PROGRAM RESERVATION to select a suitable full automatic program ET PROGRAM RESERVATION After switching on the Standard program will be the default If other full automatic program is desired you can press the button PROGRAM RESERVATION to getthe corresponding indicator on Refer to the Button of PROGRAM RESERVATION paragraph on page 10 Page 10 Ls Example Use the Quick program for slightly soiled articles If there is water inside the tub the machine cannot detect the laundries and will display middle level If wet laundries are put in it may display high level You must set suitable water level by yourself 11 Attention e Even there s no water in the tub the spinning will start after a certain period e Do notuse soak process for woolen KA laundries e Wash the laundries that are prone to lose J colors
8. User s manual Full Automatic Washing Machine This manual is for HWM50 10 HWM50 10B e Please read this manual carefully before using Retain it for future reference Juaanna Contents D k Names of the RAINS sascnccosinnnctntomsncicena aieatindtopsuchanndauastesiiasnssipciaentiatansnnspsbendicts 1 Safety PMC MUNIN srirrsiiriiesrorsriricaes intiera aitaa naait 2 Installation and adjustment cs css es cesaeesdiihesnanchecisinsiSiSeibobcehetadiaaookctialeedaaotiil 4 Install the water inlet NOSC ssscssessseesssseecseessseessstssscseeesssessesteesneesseatesnasss 6 Preparation before washing scabs ietcee devin tacci cas lececed Necdeedascecdedeavnodntas 8 Put in UGMIAUMONGS scatsice apctaratasieetie tbet ncaa ded oe iicmionadece 9 Usage of the detergent seas reeceectseae cca yets racist ncieactan teas eoeuaeees 9 Use the operation buttons siss ccesosctsccosecanessntecaevescascasactecsasbecbiasceunsniantessaenuasoussaban 10 Close the top ld taki ese a e e Oe nslaate eta 13 FINISAR WASAN sisetermgsnsnnsnrin ana E 13 Disposal after washing 26 25 recheck cS acttet ces aetna an Sierra eecterietcd 14 Trouble shooting e Answer to QUESTION ssstescsssssstessstessstessntecntesseies 15 Packing list APPGR MGR OM iecacctaccicns schiads cds aenosascbdecleaivesbceca eepeyetadarcin cng Bes 16 k Names of the parts Top lid B Control panel Filter cover Inner tub Pulsator Control panel film Cabinet
9. arge and the jointer can not be set on the water tap please loosen the four screws and take out the bushing in the jointer See to the figure3 Water inlet pipe jointer ta Slider Figure 1 3 Fasten the four screws evenly See to Figure 4 Water inlet pipe Figure 2 4 Take off the nameplate Twist the fastening nut as per the indication of the figure See to Figure 5 Remarks Before twisting the fastening nut the thread is4mm above the upper surface ofthe nut After twisting the fastening nut thethread is 2mm above the uppersurface of thenut See to Figure 6 About 4mm before twisting About below 2mm after twisting Figure 6 wo Connection between the water inlet hose and the washing machine 1 Do not take off the water absorption Nut of the water inlet hose cushion Please checkif the cushion is dropped ordamaged before each usage If ithappens please contact our after sale departmentimmediately 2 Put the nutof the waterinlet hose on the valve jointer 3 Fasten the nut Swaying it gently to Water absorption cushion confirm if it s suitable Jointer of the water inlet valve vonnectc between the jointer of the water inlet hose andthe n he water inlet hose 1 Push down theslider Insertthe Jointer of the water water inlet hoseinto the jointer inlet hose Locking lever Ce Slider 2 Hang the locklever to thejointer 4 Release the slidertill a click sound is heard
10. aundries and the laundries can be turned round in washing Towash thin laundries like the stocking silk etc pleasefirst put theminto washing mesh bag which canbe purchased separately before wash Usage of the detergent Inlet box of the detergent How to usethe whitener Fill water to decided level Dilute the whitener with container Pour it slowly into the washing tub Avoid using whitener on laundries with color or pattern as they are prone to lose color The whitener shall not touch the laundries directly Refer to the user s manual for the usage and quantity of the whitener For powder whitener please dissolve it before use How touse the washing powder Direct dissolvedin the machine 1 Fill water to Low water level 2 Add the power Run for 30 seconds to dissolve it completely 3 Put in thelaundries Select suitable water level The instant dissolving of the washing powder 1 Prepare warm water of 30 Cand a container 2 Add the powderwhile stirring to fully dissolve it Put inthe proper quantities detergent according to the water level and the laundries quantities It is suggested notto use high sudsing detergent Washing powder with poor quality or long time storage maybe caked Please pay attention tocleaning the detergent boxin time Use the operation buttons a Description of the function of the buttons SURPLUS MIN POWER ON OFF button e To in
11. c The handicapped or children without care shall not use the machine To prevent the lint inside the tub from blocking the cascade outlet during washing please keep the lint filter in good condition and install it to proper position If the lint filter is lost or damaged please contact the local after sales service department of our company Wy Dismantle Keep the machine away from direct sunlight and heat source like the heater Toprotect your laundries and wash ing machine please take out all of the coins buttons sand hairpin and other foreign materials before washing Q AO Please check if the water faucet is open and ifthe connection of the water inlet pipe is proper It is suggested to use foamless washing powder Installation and adjustment Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine Install the lint filter Install the bottom plate a After you open the package please lean Push the lint filter downward to the washing machine gently down on soft location for lint filter items like the towel cloth blanket etc Install the bottom plate to the bottom of the machine with the seven screws by a cross screwdriver then lift the machine up gently See to the figure Back Front Bottom plate Soft items A Adjust the installation po
12. dicate remaining min During Press Power On Off button to connect program running power supply ees To indicate remaining reserved After power isconnected pressing this button will cut off the supply time hrs during reservation period To indicate fault symbols for abnormal conditions see page 15 START PAUSE button After the poweris switched on press it to start the machine During working pushit to pause working m During pause pushthis button torestart and continue operation fo C a SEB EB BB RBBB eeee a L Li L PROGRAM STATUS PROCEDURE STATUS L eee Onis SURPLUS WIN E ar STANDARD m SOAK Z Oww 2 1 w JEANS bb WASH z Ow z LI GENTLE m RINSE Ouni gt n i QUICK WASH ag SPIN gt 0s WASH CN POWER w SPIN 2 START ONIOFF _PROGRAN PAUSE WATER LEVEL RESERVATION i z a E 1 Toe ee eee E n G y PROGRAM RESERVATION button z Press PROGRAM RESERVATION button you can select one or several programs of WATER LEVEL button Standard Jeans Gentle Quick Wash Wash and Spin aeae A water level e Press PROGRAM RESERVATION button over 2 seconds you can select the program of reservation The nixie tube displays the reserved hours to the wash cycle end Then pressth e START PAUSE button the indicator flashes to indicate in reservation Remarks 1 After pressing POW
13. er inlet If the cabinetis dirty wipe itwith wet cloth valve is likely to be blocked by e Do not flush it directly with water foreign materials andinfluence the water inlet Please clean it e Wipe it with neutral detergent Do not wipe it with thinner petrol alcohol etc 1 After washing close the water faucet If needed you can dismantle the water inlet hose 2 Do not store water in the washing machine for a long period Drain the water completely after each using 3 Be sure to pull off the power plug before maintenance 4 Hang up the power cord and drain hose 5 Wipe off the water drops on the surface of the machine and inside the tub Open the top lid for some time about 1 hour then close the top lid 14 Trouble shooting Answer to question If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale service department of ourcompany Do not repair it by yourself Phenomena The reason How to settle Buzzing upon reservation starts Nixie tube indicates E0 The top lidis not closed Close the top lid No orslow drain nixie tube indicates E1 buzzing Is the drain hose put down Is the drain hose blocked by foreign material Put down the drain hose Open and cl
14. or coins sand zippers shall not exceed buttons of the the laundries hairpins etc the rated value laundries may The big laundries cause noise For like the jeans the sake of shall be put in discretion please loosely put the laundries with buttons into other laundries R T 2 So e S a Please check if the laundries are applicable for washing b Separate those not colorfast from other laundries c For laundries not water absorbing please put them into water with hands d For laundries with much soil please remove the soil first You can add detergent on the part with serious soil directly It is much easier to remove the soil by that mean e For laundries likely to get lint ball or with long fiber please first turn the inside out before putting them into the water f Do not put the laundries polluted with chemicals directly into the washing machine For those small laundries laundries likely to be twisted or worn and woolen laundries please put them into mesh bag before washing Put in the laundries e The capacity of washing andspinning of the machine refer to the largestweight of the standard laundries under dry condition that can be washedor spinned inone time One time washing quantity shall be lower thanthe rated capacity The thickness size type ofthe cloth willinf luence the actual washing capacity It is sui table for onetime washing to put inreasona ble amount ofl
15. ormal sound inside the machine Is the machine slanting Are the laundries slanting in spinning Level the machine properly Re order the laundries The water faucet leaks Is the jointer screw of the water inlet hose is loose or twisted awry Fasten the jointer screw properly Common phenomena Phenomena The spinning is intermittent when it starts Explanation Balance the laundries to avoid slanting e Push the Procedure selection button to select Spin but it doesn t work e The program is setting the drain time Some time is needed before it starts spinning There may be some water flowing out of the drain hose in the first use of the machine performance It is the water remained in the factory inspection of e While water filling in wash and rinse the pulsator pauses rotation To prevent splash during water filling Wash pauses 15 Supplementary water filling 48 s after sensor tests cloth material Packing list a Name Quantity gt User s manual e One piece Components of the water inlet hose e One piece Lint filter One piece Bottom plate One piece Tapping screws F e Seven pieces A A g Full automatic washing machine e One set Specification High About 48 L Medium About 37L Water level Water quantity about Low About 30L Very low About 20L 0 03MPa
16. ose the top lid once Clean the foreign material Open and close the top lid once Running pauses nixie tube indicates E2 buzzing The top cover leaves open Close the top lid Safety switch actuates not spin after self correction twice nixie tube displays E3 buzzing Are the laundries put slantingly Is the machine slanting Re order the laundries Close the top lid Level the machine in right position Open and close the top lid once No orslow water filling not reaching the level in 15min nixie tube indicates E4 buzzing The water tap is notopen The water inlet valve is blocked The water pressureis too low and thecurrent is too small Open the water tap Push the Start Pause button Clean the water inlet valve Push the Start Pause button Wait for the normal water pre ssure before use Poor or no waterfall flow f the nozzle is choked with foreign bodies Remove the foreign bodies Not wash The machine does not act Is there power failure Is the power plug loose Does the water level arrive atthe set water level Use it when the power is on Insert the power plug tightly Affusion to the set water level Not spin Is the power plug loose Is thetop lid closed Are the laundries put orderly Insert the power plug tightly Close the top lid Put the laundries orderly There s abn
17. sition The largest allowed slope of the shank base of the machine is 2 The slanting or rough ground will result in unstable running or stoppage of the machine Please adjust it with following methods RA Adjust the adjustable foot 1 To twist the adjustable foot please first lift up the side of the foot slightly loosen the adjustable nut and twist the foot 2 Fasten the nut after adjustment z j adjustable nut N Fasten adjustable foot How to change the direction of the drain hose 1 Dismantle the back cover of the washing machine 2 Put down the drain hose Take off the drain hose frame As indicated in Figure 1 put the drain hose into the cabinet Then stretch one hand into the cabinet to nip the claw of the drain hose bush ing to remove the claw from original position Take off the drain hose bush ing with the other hand As indicated in Figure 2 and 3 Drain hose bushing Figure 2 Drain hose frame Figure 1 Cabinet 3 Dismantle the protecting cover of the drain outlet at the other side method the same as the bushing Install the bushing as per indicated in Figure 4 4 Extend the drain hose from the other side Fix the drain hose onto the base frame with the drain hose frame As indicated in Figure 5 Drain outlet protecting cove Drain Kose bushing Figure 5 Figure 4 5 Install the protecting cover of the drain outlet at the other side as
18. t press or nip it with weight If the power cord or the power plug is bad or the power plug becomes flexible to avoid risk it is required to have it replaced by the technicians of our special shop or the after sale service department Keep the pin of the power plug clean if the power plug is polluted with dust please P Do not put the machine at damp place like the bathroom Never wash it with water Not put wet laundries on the control panel Do not use water hotter above 50 C sY 9 In case the washing machine is installed on ground with carpet do not block the ventilation hole with carpet The ventilation holes at the bottom soft items Do not wash water proof laundries like the raincoat bike covers etc to avoid abnormal vibrations in spinning the plugging into the receptacle is loose do not use the plug any more NC Do not let the machine share one receptacle with other electric appliances If the power plug is damaged or O J Safety precautions Do not stretch hands into the working machine It is dangerous even if the rotation is slow Take special care of the children Do not let the children climb the washing machine Do not decompose repair or alter the machine by yourself Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wash laundries with volatile materials such as thinner petrol et
Download Pdf Manuals
Related Search