Haier HWC1070TVEME Washer User Manual
Contents
1. Eco button _ Before a washing program press this button to set the required washing load 1 3 Full the wash ing machine will automatically adjust the water consumption heating time and washing time Users can select the washing load as required for economical operation Note 1 1 3 Full refers to the four levels of washing load If the laundry is more than half of the drum content it is recommended to select 2 3 Full otherwise select 1 3 1 2 2 For synthetics sport you can only select 1 3 1 2 2 3 3 Please adjust the detergent quantity according to the washing load selected F Rinse hold _ f you press this button the washing machine will not drain the water after the last rinsing opera button tion but start a soaking cycle The indicator light goes on To spin the laundry press this button again The indicator light turns off and the program continues to the end Note Press only when Prewash Cotton amp linen Synthetics or Rinse is selected G Extra rinse _ Press this button the washing machine will perform additional rinses The light turns off and the button display disappears when the extra rinse ends Note Select this function when programe 1 6 or 9 is selected H Delay button _ Press the button repeatedly before starting the program to enter the time you want the machine to be finished in the start will delay from 0 5 to 24 hours in 30 minute intervals This also includes the length of the program itself s2. collection point for recycling Some collection points accept products free of charge We apologise for any inconvenience caused by minor inconsistencies in these instructions which may occur as a resultof product improvement and development COMPONENTS Please read these instructions carefully before using this appliance The instructions contain important information which will help you get the best out of the appliance and ensure safe and proper installation use and maintenance Keep this manual in convenient place so you can always refer to it for the sate and proper use of the appliance If you sell the appliance give it away or leave it behind when you move house make sure you also pass on this manual so that the new owner can become familiar with the appliance and safety warnings ACCESSORIES Check the accessories and literature in accordance with this list 1 Inlet hose assembly Bottom cover 1 User manual Ix Drain hose bracket 2 3x Blanking plugs 6 PREPARING THE MACHINE Remove all the packing materials to prevent unsteadiness including the polystyrene base Upon opening the package water drops may be seen on the plastic bag and the porthole This is normal phenomenon resulting from water tests in the factory DESCRIPTION This diagram may be slightly different from the layout of the washing machine you have just purchased due to technical improvements
3. speed It is advisable to select the recommended value WASHING Press the Start Pause button The washing machine will operate according to the pre set programs The washing machine will stop operation automatically when a washing cycle ends The End sign wil appear on the display Open the washer door and take out the laundry AFTER WASHING Turn off the water supply and unplug the power cord Open the washer door to prevent formation of moisture and odours Let the door open while not used TIPS FOR SAVING ENERGY Collect clothes for one full wash load Avoid overloading the washing machine Pre wash only heavily soiled clothes Reduce the amount of detergent or choose the speed up wash programs for slightly soiled clothes Choose a proper washing temperature Modern detergents can wash with very good result already in lower temperature than 60 C Only user higher temperature than 60 C for heavily soiled laundry 6 Follow the dosage recommendation on the detergent package to avoid using too much detergent CARE CHART BERR ig E EEA 77 Resistant material Delicate fabric Washable at 95 C Washable at 60 C Washable at 40 C Washable at 30 C Hand wash Bleachable in cold water Do not bleach at 200 C at 150 C at 100 C Don t iron Dry cleaning with any solvent Don t dry clean Dry flat Dry on clothes hanger C Tumble
4. AUTOMATIC DRUM WASHING MACHINE USER MANUAL HW D1270TVE HW D1270TVE ME HW D1470TVE HW D1470TVE ME Oi ABLE OF CONTENTS BEFORE USE USING THE APPLIANCE MAINTENANCE SUUMPUNENID 3 PROGRAM SELECTION gt CLEANING amp 16 SEREPARATIDN cte 4 CONSUMPTION AND TECHNICAL DATA 11 DISPLAY 0066 18 gt SAFETY INSTRUCTIONS 5 WASHING METHODS 12 2TROUBLESHOOTING i2 INSTALLATION 6 SCONTROL PANEL 8 LEGEND Optional For your safety any instructions in this manual with this Warning sign must be followed strictly DISPOSAL As a responsible retailer we care about the environment As such we urge you to follow the correct disposal procedure for your product and packaging materials This will help conserve natural recourses and ensure that it is recycled in a manner that protects health and the environment You must dispose of this product and its packaging according to local laws and regulations Because this product contains electronic components the product and its accessories must be disposed of separately from SS household waste when the product reaches ifs end of life Contact your local authority to learn about disposal and recycling The product and packaging should be taken to your local
5. Power switch Drain hose Door handle Nater inlet valve Work Top Power cord Washer door Back cover Control Panel Back cover screws Detergent distribution drawer Transportation bolts Filter cover oust NC SS PN 7 el IT i iue tit c Ti T3 53 S SAFETY INSTRUCTIONS BEFORE SWITCHING THE APPLIANCE ON FOR THE FIRST TIME DO make sure that the transport bolt are removed Use separate earthed socket for the power supply Make sure that the plug is accessible Hold the plug and not the electric cable when unplug ging the power supply V Make sure that the fuses in the power circuit are rated for 15A MI Keep away from heat sources and direct sun light to prevent plastic and rubber components from aging Make sure that the power cord is not caught under or in the appliance and avoid damage to the power cable Check that hose joints and connections are firm and water can leak If joints are loose or there is leakage turn off the water supply and repair Do not use the washing machine until the hoses are properly fixed DURING DAILY USE OF THE APPLIANCE DO Pull up zips and fix loose threads to prevent the items from being entangled If necessary put small items into a net bag or pillow VT Turn off the machine after eac
6. ace the filter by turning clockwise and remount the cover Caution The filter must be in place or it may lead to leakage 2 Place a container under the drain pump filter to collect any excess water that may come out of the drain pump when the filter is removed WATER INLET AND INLET FILTER To prevent blockage to the water supply by ingress of foreign substances clean the water inlet and inlet filter regularly MOVING THE MACHINE If the machine is to be moved to a distant location replace the transportation locks removed before installation to prevent damage as shown below Remove the blanking plugs Remove the back cover Insert the synthetic stabilisers and the transportation bolts Tighten the bolts with a spanner Replace the back cover LONG PERIODS OF DISUSE If the washing machine is left idle for long period pull out the electrical plug and turn off the water supply Open the washer door to prevent formation of moisture and odours Let the door open while not used DISPLAY CODES DISPLAY CODES AND SPECIAL FUNCTIONS CODES CAUSES SOLUTIONS Err Washer door is not properly shut __ lose the washer door properly Err2 Drainage error lean the filter and check the drain hose for block age Temperature sensor error _ Please contact the Service Center Appears at the end of a cyde Errd Heater error Appears at the end of a
7. cycle _ Please contact the Service Center Err5 Water inlet error _ Check the tap and the water pressure Err Motor error _ Please contact the Service Center Err7 Motor error _ Please contact the Service Center Err Water exceeds protective level _ Please contact the Service Center unb Laundry is unevenly distributed _ Redistribute laundry to balance the drum End End of wash cycle 1 16 Remaining time is 1 hour and 16 minutes 0 01 Remaining time is minute 60 Preset washing temperature is 60 C Cold wash 000 Preset spinning speed is 800rpm Control panel lock function Press the Delay and the Start Pause buttons simultaneously for 3 seconds after starting a program It can no longer be changed by operating buttons or knobs The washing machine emits an audible signal while the control panel is locked To unlock press the Delay and Start Pause buttons again for 3 seconds Power off memory function In case of abrupt power failure or the need to cut off the power during a program cycle the pres ent settings will be saved and the preset operation will resume when the power is on again To cancel a program or select a new program and options during the wash cycles 0 Press the Start Pause button then switch off the power and the program is automatically cancelled Turn the program selector again to choose another program b If you wish to select an option during the wash cycle pres
8. dry normal Tumble dry reduced heat Don t tumble dry 57 Dry clean only Wool Seal Dry cleaning with pericloride GM UU Dry cleaning with aviation fuel LOAD REFERENCE Bed sheet single Cotton Approximately 800g Blanket Wool Approximately 3000g Blended fabric dothes Approximately 800g Jackets Cotton Approximately 800g Jeans Approximately 800g Overalls Cotton Approximately 950g Ladies Pyjamas J Approximately 200g Shirts Approximately 300g Socks Blended fabrics Approximately 50g T Shirts Cotton Approximately 300g Underwear Blended fabrics Approximately 70g CLEANING amp CARE AFTER WASHING Turn off the water supply and pull out electricity plug after each wash Open the washer door to prevent formation of moisture and odours If the washing machine is lett idle for a long period drain the water in the machine and replace the drain hose CLEANING THE DETERGENT DRAWER Clean the detergent distribution drawer regularly Swing out the drawer flush it clean with water and then replace it CLEANING THE MACHINE Unplug the machine during cleaning and maintenance Use a soft cloth dampened with soap liquid to clean the machine case and rubber components Do not use organic chemicals or corrosive solvents CLEANING THE FILTER Clean the filter once a month Open the bottom cover 2 Remove the filter by turning counterclockwise 3 Flush the filter clean with running water 4 Repl
9. e Do not add more detergent than needed Please follow the dosage recommendation on the detergent package ADDING DETERGENT Slide out the detergent drawer and put the required detergent and softening agent into the corresponding compartments Push back the drawer gently Refer to the instructions on the drawer Caution For pre washing program detergent should be added to both compartments 1 and 2 For other programs do not add detergent to compartment 1 Use liquid detergent according to the instructions on its package Do not use liquid detergent if the pre wash mode or Start delay is selected Do not overuse softener otherwise it will damage the artificial fibers SELECTING PROGRAM To get the best washing results an appropriate washing program should be selected according to the laundry type There are instructions on the handle of the detergent distribution drawer Please turn the program knob to select the right program SELECTING FUNCTIONAL Select the required options Refer to the Control panel pages 08 and 09 SETTING WASHING TEMPERATURE Press and hold down the temperature button until the desired temperature is selected or the symbol for no water heating SETTING SPIN SPEED Press and hold down the speed button until the desired speed is selected or the symbol 0 is selected for no spin See Operational functions on the Control panel pages 08 and 09 for selecting temperature and spin
10. h wash program and switch it off at the mains to save electricity and for safety Wipe dean the lower part of the porthole Keep the door slightly open when the washing machine is not in use to prevent formation of odours Let the power cord be replaced by the manufacturer his service agent or other accordingly qualified persons in case it is damaged V Ensure that the appliance is not used by persons with re duced physical sensory or mental capabilities lack of experience and knowledge without supervision or instruction by a person responsible for their safety v Supervise children to ensure that they do not play with the appliance DO NOT Touch or use the appliance when barefoot or with wet or damp hands or feet Use flammable detergent or dry cleaning agent Use any flammable sprays in dose vicinity to the appli ance Remove or insert the plug in the presence of flammable gas Allow children or infirm persons to play with the appliance or packing materials Install the appliance outdoors in a damp place or in an area which may be prone to water leaks such as under or near a sink unit In the event of a water leak allow the machine to dry naturally Place the washing machine directly on a carpet or close to wall or furniture DO NOT a Touch the washer door during the washing process it gets hot Place heavy objects or sources of heat or damp on top of
11. in the power circuit should be rated for no less than 15A The voltage should meet the requirement The power outlet should be capable of accepting the washing machine plug Connect the machine to an earthed socket outlet CONTROL PANEL A Program knob F Rinse hold button K Power button B Temperature button G Extra rinse button Speed button H Delay button D Start pause button Display E Eco button Detergent distribution drawer OPERATIONAL FUNCTIONS A Program knob Temperature button Speed button D Start pause button _ Select program by turning the knob _ Select the desired washing temperature 30 40 50 60 90 C by pressing and holding down this button When selected the temperature is shown on the display Cold wash is selected when the symbol is displayed _ Select the desired spin speed 0 400 600 800 1000 1200 by pressing and holding down this button When selected the speed value is shown on the display The washing machine does not spin when 0 is displayed The washing machine spins at 1200 rpm when 1200 is displayed _ If you press this button will be displayed and operation will start If you press this button during wash cycle the sign will start blinking and operation will pause Press it again to resume opera tion Note After operation is suspended the washing temperature spinning speed and other functions can not be reset E
12. lear Note Before use check for leakage in the joints between the tap and the inlet hose by turning on the tap PREPARING THE LAUNDRY Sort out clothes according to fabric cotton synthetics wool or silk and to how dirty they are Separate white clothes from coloured ones Wash them first by hand to check if they fade or run Empty pockets keys coins etc and remove the harder decorative objects e g brooches Garments without hems underwear finely woven textile such as fine curtains are to be put into wash bag it is better not to wash them in a washing machine lose zippers and hooks make sure the buttons are sewn on tightly and place small items such as socks belts bras etc in the wash bag Untold large pieces of fabric such as bed sheets bedspreads etc Turn shirts inside out SELECTING DETERGENT LOADING THE MACHINE Open the washer door put in the laundry piece by piece Close the door tightly When first using the washing machine let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing machine Do not overload the washing machine The washing efficiency and the performance is determined by the quality of detergent used Special non foaming detergent produces good washing results Use specific detergents for synthetic and woollen goods Do not use dry cleaning agents such as trichloroethylene and similar products Not
13. o the delay time must be longer than the program length selected Display _ The display shows the washing time remaining the selected temperature and speed the options the alarm warning etc Detergent _ Instructions are printed on the handle of the drawer distribution drawer Open the drawer three compartments can be seen Compartment 1 Pre wash detergent Compartment 2 Detergent for programs 1 to 8 Compartment 3 Softener conditioning agent pertume and other additives K Power button _ Press this button to turn the machine on and off PROGRAM SELECTION PROGRAM MODES Program 1 Prewash 2 Cotton amp linen 3 Synthetics 4 Wool 5 Handwash 6 Silk Sport 8 Quick wash 9 10 Spin 1l Drain v Yes Temperature Maximum C to 90 C 0 to 60 C 0 to 40 C 0 to 40 C 0 to 40 C 0 to 40 C 0 to 40 C Preset 40 C 40 C 40 C 10 10 Optional 1 Detergent compartment for prewash mode 4 2 Detergent compartment 3 Compartment for softener and other additives Recommended Laundry Preset spin speed Cotton fabrics 1000 rpm Cotton fabrics 1000 rpm Fast colours Medium 1000 rpm soiled Wool fabrics Cotton or synthetic 1000 rpm 1000 rpm 1000 rpm 7 1000 rpm CONSUMPTION AND TECHNICAL DATA CONSUMPTION TABLE The wash cycle times are intended as a guide only The actual time
14. o the power supply Check connection to the power supply Power failure Check the power supply The washer door is not properly closed _ Close the washer door properly Machine has not been switched on _ Make sure the machine is switched on The Start Pause button is not pressed press the Start Pause button Water tap is not turned on _ Turn on the water tap Water pressure is less than 0 03 MPa Check water pressure The inlet hose is kinked _ Check the inlet hose Water supply failure _ Ensure the water supply The program knob is not properly set _ Set the program knob properly The washer door is not properly closed Close the washer door properly The inlet hose filter is blocked Unblock the inlet hose filter The height of the drain hose is below 80 cm _ Install drain hose within 80 100 cm of height The drain hose is in water _ Make sure the drain hose is not in water Drain hose is blocked Unblock the drain hose Drain hose end is higher than 100 cm above _ Make sure the drain hose end is lower than the floor level 100 cm above floor level The filter is blocked Unblock the filter Not all transportation bolts have been removed _ Remove all transportation bolts Washing machine is located on an uneven _ Make sure the washing machine is on surface or is not level an even surtace and levelled Machine load is over 7 kg _ Reduce amount of laundr
15. s the Start Pause button then select the desired option and press the Start Pause button again Note 1 The Rinse hold function can be selected directly without pressing first the Start Pause button but before the machine starts the spin program 2 Marm sound can be cancelled if it is needed Please follow the instruction as below Switch on the washing machine and turn the program knob to spin cyde then press the delay button and hold on for 3 seconds The b OFF will be displayed on the screen which indicates that alarm sound has been canceled To operate the above steps again so the alarm sound can be recovered and the display will show b ON 3 CLRF Too much foam used in wash cycle Washing machine can eliminate the foam automatically during spin the washing machine fails to eliminate the excessive foam it will end the cycle without spinning TROUBLESHOOTING TROUBLESHOOTING The following circumstances do not constitute problems Do not contact the Service Center until the problem has been confirmed PROBLEM Washing machine fails to operate Washing machine cannot be filled with water Machine is draining while being filled Drainage failure Strong vibration while spinning Operation stops before completing wash cycle Excessive foam in the drum which is spilled to the distribution drawer Automatic adjustment of the washing time Spinning fails CAUSES SOLUTIONS Poor connection t
16. ter use Adjusting the washing machine There are adjustable feet under the bottom of the washing machine Before use they should be adjusted so that the machine is level This will minimise vibrations and thus noise during use It will also reduce wear and tear We recommend using a spirit level to level the appliance INLET HOSE 1 Connect the nut on the inlet hose to the connector on the water valve 2 Apply inlet hose to a water tab with cold fresh water Note Use the hose set supplied with the appliance Old hose sets should not be reused DRAIN HOSE 1 Use the drain hose bracket to keep the end of the drain hose retained and prevent the outflow of water Don t extend the length of the drain hose if an extended hose is required please consult a serviceman 2 The height of the drainage outlet must be 80 100 cm Fix the drain hose to the clip at the back of the washing machine to prevent it from dropping off Note The drain hose should not be submerged in water and should be securely fixed and leak free If the drain hose is placed on the ground or if the pipe is at a height of less than 80cm the washing machine will continuously drain while being filled self siphoning CONNECTING TO THE POWER SUPPLY Before connecting to the power supply check The socket is adequate for the maximum power of the washing machine For safety fuses
17. the appliance Hot wash foam rubber or sponge like materials Open the detergent distribution drawer during the wash cyde Force the washer door open The door is fitted with a self lock device and will open shortly after the washing procedure is ended Open the washer door if the water level is visibly over the porthole Cover the washing machine with plastic cover so that inside dampness cannot be kept in INSTALLATION ADJUSTING THE BOTTOM COVER When open the shrink package you will find a calcium plastic board which is laid on the top of washing machine as shown in fig 1 The board is used for reducing noise by pasting it under the cabinet when setting as shown in fig 2 It keeps out the dampness and reduces the noise DISMANTLE THE TRANSPORTATION BOLTS The transportation bolts are designed for clamping anti vibration components inside of the washing machine during the transportation process 1 Remove the back cover 2 Remove the three bolts on the rear side and take out the synthetic stabilisers from within the machine 3 Replace the back cover 4 Fill the holes left by the bolts with blanking plugs Note 1 When you replace the back cover the convexity must face to outside and you have to insert the back cover from the two gaps as shown in fig 3 2 Keep the transportation bolts and synthetic stabilisers in a safe place for la
18. used may vary due to different water pressure initial water tempera ture PROGRAM Prewash Cotton 60 C Cotton 40 C Synthetics Wool Handwash Silk Sport Quick Hand wash MAX LOAD 7 kg 7 kg 7 kg 3 kg 2kg 3 5 kg 2 kg 3 5 kg 3 5 kg 4 kg ENERGY WATER CONSUMPTION CONSUMPTION 0 89 kWh 1 19 kWh 601 0 66kWh Ibit 0 475 kWh 55L 0 055kWh 441 0 017 kWh 441 0 03 kWh 441 0 3 kWh 34 0 37 kWh 34L 0 147 kWh 41 81 EN 60456 test program Energy label program with Cotton 60 C and max spin speed TECHNICAL DATA Power source Max working current A Water pressure MPa Nominal load kg Spinning speed r min Washing programs Max power W Dimensions HxDxW mm Net weight kg HW D12701VE ME 220 240 V 50 Hz 10 1200 12 2000 840 x 610 x 595 0 HW D1470VE ME 220 240 V 50 Hz 10 Apt esto s 7 1400 12 2000 840 x 610 x 595 72 WASHING TIME 2 32 h 2 58 h 1 35 0 41 h 0 39 h 0 41 h 0 25 h 0 29 h 0 57 h ASHING METHODS PLEASE NOTE This washing machine is for domestic use only Do not use it for purposes other than that for which it was designed Follow the instructions given on the label of each garment and wash only machine washable garments POWER SUPPLY Connect the washing machine to the power supply 220V to 240V 50Hz WATER CONNECTION Turn on the tap The water must be clean and c
19. y in the drum Water or electricity failure Check the power supply Washing machine is in rinse hold cycle _ Press the rinse hold button Washing machine gives an error message _ Check display codes The detergent is not a low foaming type or for Check if your detergent is appropriate manual wash Excessive use of detergent _ Reduce amount of detergent in the distribution drawer The washing program duration will be adjusted This is normal and doesn t affect the according to the laundry load and the initial water functionality temperature Unbalance of the laundry _ Add clothes or run a spinning program again Haier Europe Trading S r l Tel 39 0332 24511 Via De Cristoforis 12 Fax 39 0332 245146 e 21100 Varese Italy E mail het srl haiereurope com Ha
Download Pdf Manuals
Related Search