Haier DWL3025 Dishwasher User Manual
Contents
1. May be reduced to 337 s 86 cm by removing wheels from dishwasher Minimum measured from narrowest point of opening Maybe increased to 6 s 17 5 cm if height of opening is 34 87 6 cm at lowest point A WARNING Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher Failure to do so can result in death or electrical shock Do not use an extension cord or adapter plug with this appliance A PREPARE CABINET 1 Disconnect the power supply Turn water off Put on gloves and safety glasses 2 If you are replacing a dishwasher Check that the water line A reaches to the back left of opening where the water connection will be made Check that the direct line B reaches to the back left of opening where the electrical connection will be made If the water line and the direct wire reach into the opening far enough go to step 10 page 12 If you are installing a new dishwasher complete all of the following steps Electrical Follow all national and local codes and ordinaces for completing electrical supply to cabinet Direct Wiring 3 4and5 10 HELPFUL TIP Wiring the dishwasher will be easier if you route wire into the cabinet opening from the left side 3 Direct wire method Cut a 34 1 9 cm hole C in righthand cabinet side rear or floor Optional locations are shown Wood Cabinet Sand hol2. 7 cm 15 2 cm 7 cm 16 6 Stand dishwasher upright 7 The dishwasher must be secured to the cabinet There are two brackets on top of the dishwasher that usually can be attached to the countertop If this is not possible the brackets M may be moved to the sides of the dishwasher If you are going to attach the dishwasher to the countertop skip to step 13 If you are going the attach the dishwasher to the sides of the cabinet follow steps 8 through 12 8 To remove the brackets from the top flatten tab N at back of brackets with pliers and pull the brackets out of the slots O 9 Break off the end of the bracket along the scored line P 10 Open dishwasher door and place towel Q over pump assembly and spray arm of dishwasherThis will prevent screws from falling into pump area when securing dishwasher to countertop 11 Open dishwasher door and push the plastic buttons R out of the side of the tub NOTE Save the buttons to cover the holes after dishwasher is installed 12 Push bracket into slot S on the side of dishwasher and bend tab in towards the side of the dishwasher so that it keeps the bracket in place 17 13 14 15 16 17 Check the door spring tension With another person holding the dishwasher to prevent it from tipping open and close the door a few times If the door opens by itself adjust the door spring tension To adjust the
3. 75 C We recommend a time delay fuse or circuit breaker a separate circuit If direct wiring dishwasher Use flexible armored or non metallic sheathed copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances Use strain relief method provided with house wiring junction box or install a cUL listed CSA certified clamp connector to the house wiring junction box If using conduit use a cUL listed CSA certified conduit connector If connecting dishwasher with a power supply cord Use a cUL listed 16 gauge three conductor power supply cord that meets all local codes and ordinaces Maximum length of the power supply cord is 6 feet 1 8 m A clamp connector to fit a s 2 2 cm diameter hole is required to secure power supply cord to dishwasher terminal box Power supply cord must plug into a mating three prong grounded outlet located in the cabinet next to the dishwasher opening Outlet must meet all local codes and ordinances A WARNING Electrical Shock Hazard The improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician if you are in doubt that the appliance is properly grounded WATER You must have A hot water line with 20 120 psi 138 862 kPa water pressure 120 49 C water at dishwasher 3 8 0 9 cm O D tubing with compression fittin
4. Flush water into a bucket to get rid of particles that may clog the inlet valve 9 Turn shutoff valve to OFF position Drain Hose 10 Cut a 1 3 8 cm diameter hole in cabinet wall or floor on the side of the opening closest to the sink 11 Connect drain hose to waste tee or waste disposer following one method A Waste Disposer No Waste Disposer An air gap is recommended 11a Waste disposer air gap 1 Remove the disposer knockout plug Cut end of drain hose I if needed do not cut ribbed section 2 Attach drain hose to air gap J with large spring type clamp K If the drain hose was cut use a 1 to 2 3 8 to 5 cm screw type clamp 3 Use a rubber hose connector L with spring or screwtype clamps M to connect air gap to disposer inlet N This connection N MUST be before drain trap O and at least 20 50 8 cm above the floor where dishwasher will be installed Go to step 12 12 11b No waste disposer air gap 1 Cut end of drain hose I if needed do not cut ribbed section 2 Attach drain hose to air gap J with large springtype clamp If the drain hose was cut use a 1 to 2 3 8 to 5 cm screw type clamp 3 Use a rubber hose connector L with spring or screwtype clamps M to connect air gap to waste tee P This connection P MUST be before drain trap O and above the floor
5. be outside the box on the W right side Make sure no wires are pinched by cover Do not leave the box without the cover 1a Power Supply Cord Method A WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet Do not remove ground prong Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock Check that power supply cord does not touch dishwasher motor or lower part of dishwasher tub Go to step 5 Water Connection HELPFUL TIP Compression Fittings 1 Slide nut I onto copper tubing J about 1 2 5 cm 2 Slide ferrule K onto the tubing Do not position ferrule on the end of the tubing 3 Put the tubing into the elbow L as far as it will go 4 Slide the nut and ferrule forward and start the nut onto the elbow threads M Be careful when handling and positioning the copper tubing It bends and kinks easily 22 5 To prevent vibration during operation route the water supply line so that it does not touch the dishwasher base frame or motor Make sure the water line stays within the shaded area shown on page 7 when the dishwasher is installed in the cabinet With copper tubing J pushed into compression fitting as far as it will go use an adjustable wrench and tighten compression fitting nut I to elbow L on water inlet valve
6. Dishwasher Installation Manual Model DWL3025 alo Tyi Quality Innovation Style TABLE OF CONTENTS PAGE Before Using YOURDISAWASHe Ditto eo dd de Od be 2 3 BUILT IN DISHWASHER INSTALLATION INSTRUCTIONS 0 0 0 0 0 ccc eee eee eee 4 10 WHAT DO I NEED TO HAVE TO INSTALL THE DISHWASHER 0 0000 e eee eee ee 4 10 TOONS ports materials ista deditos Du deo Sy ade Addon 4 5 Requiere 6 10 Cabinet DIMENSIONS vtr edad driad id 9 WHAT DO I NEED TO DO BEFORE INSTALL THE DISHWASHER 00 00 10 20 Prepare cabinet an 3 2 20 pai A Aled eaten ete tenets 10 14 PreparedishWwWashe nesi O ad ade RE 14 20 HOW DO INSTALL THE DISHWASHER cuco cocos co dd a ad 20 25 Connect CISAWOSHEM 3 a e dd ol dnd E 20 23 Secure dis Was A Lh ae dd o 24 Check Operation yuca ra oder 25 BEFORE USING THE DISHWASHER IMPORTANT READ AND SAVE THESE INSTRUCTIONS Doing so will make installation easier help you in the future if you have questions help if you have an electrical inspection This is the safety alert symbol This symbol alerts you to potential hazards that may seriously injure you and others All safety messages follow the safety alert symbol and either the word DANGER or WARNING A DANGER YOU CAN BE SERIOUSLY INJURED IF YOU DO NOT FOLLOW INSTRUCTIONS IMMEDIATELY AIN Ie YOU CAN BE SERIOUSLY
7. ING Electrical Shock Hazard Electrically ground dishwasher Connect ground wire to green ground connector in terminal box Do not use an extension cord Failure to do so can result in death fire or electrical shock Install strain relief and route direct wire so that it does not touch dishwasher motor or lower part of dishwasher tub Pull direct wire A through hole in terminal box HELPFUL TIP gt a A e Select the proper size twist on connectors to connect your household wiring to 16 gauge dishwasher wiring e Insert wire ends into twist n connector Do not pretwist Ez Bare wire ES e Twist connector e Gently tug on wires to be sure both are secured 2 Connect the wire B as follows using twist on connectors C sized to connect direct wire to 16 gauge dishwasher wire From bare ground wire D into a U shaped hook Wrap ground wire hook clockwise around ground connector E and under the washer F Securely tighten ground connector E and under the washer eR Securely tighten ground connector E Do not untie knot in the wires Power Supply Wire Terminal Box Wire White lt White Black Black Ground Wire Ground Wire 21 3 Tighten clamp connector or conduit connector screws G 4 Reinstall terminal box cover H with wires inside terminal PNTE box Go to step 5 The cover must
8. INJURED IF YOU DO NOT FOLLOW INSTRUCTIONS All safety messages will tell you what the potential hazard is how to reduce the chance of injury and what can happen if the instructions are not followed YOU NEED TO e Carefully open dishwasher door while someone grasps the rear of the dishwasher Remove shipping materials and lower rack Close dishwasher door Latch the dishwasher door shut e Install this dishwasher as specified in these instructions e Have everything you need tools materials parts to properly install the dishwasher IMPORTANT e Observe all governing codes and ordinances e Note to installer Be sure to leave these instructions for the consumer s and inspector s use e Note to consumer Keep these instructions with your owner s manual for future reference e Skill level Installation of this dishwasher requires basic mechanical electrical and plumbing skills Proper installation is the responsability of the installer Product failure due to improper installation is not covered under warranty See warranty information e Completion time 1 to 3 hours New installations require more time than replacement installations TOOLS AND MATERIALS NEEDED ALL INSTALLATIONS Pliers Phillips screwdriver 5 8 open end wrench Measuring tape or ruler 10 adjustable wrench that opens to 11 s 2 9 cm Flat blade screwdriver Gloves Utility knife 2 twist on wire connetors which are the proper
9. Operate Has the circuit breaker tripped or the house fuse blown Is the door closed tightly and latched Has the cycle been set correctly to start the dishwasher Is the water turned on 25 Y 1 9cm insulation may be compress ed Model DWL3025 k 25 63 5cm 4 H 21 53 3cm 337 8 86 cm minimum with wheels removed 52 IMPORTANT Do Not Return This Product To the Store If you have a problem with this product please contact the Haier Customer Satisfaction Center at 1 877 337 3639 DATED PROOF OF PURCHASE MODEL AND SERIAL REQUIRED FOR WARRANTY SERVICE Haier Haier America New York NY 10018 Made in China DWL3025DBWW DBBB SBSS Issued J une 09 Printed in China Part No 0120504139B
10. Place Paper towel under elbow Turn on water supply and check for leaks Drain Connection 7 10 23 To help minimize vibration noise route drain hose a J UY to avoid contact with motor door springs water 7 line cabinet flooring or the edge of the hole where o it passes through the cabinet Do not remove drain loop N from side of dishwasher Place the smaller drain hose clamp N onto the small end of the drain hose O Remove the plug MM ON from the connector P Push the drain hose into the connector P up to the rib O on the drain hose Use pliers to open clamp N and slide clamp onto connector P between ribs O on connector D SECURE DISHWASHER A WARNING Tip Over Hazard Do not use dishwasher until completely installed Do not push down on open door Doing so can result in serious injury or cuts Open dishwasher door and place towel A over pump assembly and spray arm of dishwasher This will prevent screws from falling into pump area when securing dishwasher to countertop Check that dishwasher is still level and centered in the opening Secure dishwasher to countertop with two No ST4 2 x 18 Phillips head screws B The dishwasher MUST be secured to keep it from tipping when door is opened Do Not drop screws into bottom of dishwasher Open door about 3 inches 7 6 cm and check that space betwe
11. at 154 s 40 cm to 392 s 100 cm at least 20 50 8 cm above the floor where dishwasher will be installed Go to step 12 11c Waste disposer no air gap 1 Remove the disposer knockout plug Do not cut end of drain hose 2 Attach drain hose I to disposer inlet N with large spring type clamp K This connecting N MUST be before drain trap O and at least 20 50 8 cm above the floor where dishwasher will be installed 3 The drain hose must be looped up and securely fastened to the underside of the counter before going to the drain Hose loop must be a minimum of 30 76 8cm above floor Go to step 12 i 11d No waste disposer no air gap See note 3 1 Cut end of drain hose I do not cut ribbed section alada 2 Attach drain hose to waste tee P with 1 to 2 3 8 to 5 cm screw type clamp M This connecting P MUST be before drain trap O and at least 20 50 8 cm above the floor where dishwasher will be installed O 3 The drain hose must be looped up and securely fastened to the underside of the counter before going to the drain Hose loop must be a minimum of 30 76 8cm above floor Goto step 12 AUS i Parts available from local plumbing supply stores 13 HELPFUL TIP To reduce the vibration of the hose keep the hose away from the floor and the edge of the hole where it passes through the ca
12. binet 12 Insert drain hose I into hole cut in cabinet to the back center of opening where drain connection will be made B PREPARE DISHWASHER A WARNING Tip Over Hazard Do not use dishwasher until completely installed Do not push down on open door Doing so can result in serious injury or cuts A WARNING Excessive Weight Hazard Use two people to move and install dishwasher Failure to do so can result in back or other injury 14 1 Grasp sides of dishwasher door and put dishwasher on its back 2 Remove two screws A attaching access panel B and lower panel C to dishwasher using a 1 4 hex socket nut driver or Phillips screwdriver Remove panels and set panels aside on a protective surface Check that grounding clip D is attached to the lower panel 3 Apply pipe joint compound E to 90 elbow fitting F and connect fitting to water inlet valve G Tighten elbow until snug and be sure that it faces to the rear 1 through hole in terminal box Do not untie the AWARNING 4 Remove terminal box cover H Pull appliance wires g A knot in the wires If you are direct wiring install a cUL listed CSAcertified clamp connector J to the terminal box If using conduit use a cUL listed CSA certified conduit connector If you are installing a power supply cord kit do so now and follow kit instructions HELPFUL TIP Put card
13. board under dishwasher until it is installed The cardboard will help protect floor covering during installation 15 5 Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed K you need the lowest point Check 1 chart for that height opening Put wheels L in the l required position Turn both front leveler legs to the Y same height Min Cutout Wheel Position Number of Turns Height See Illustration on Front Leg Front Leg If the minimum cutout height is less than 34 86 4 cm the adjustable legs can be removed for additional clearance This will allow the dishwasher to fit into a 334 s 85 9 cm high cutout but the dishwasher will be more difficult to move into position If the wheels are removed protect the floor when moving the dishwasher HELPFUL TIP Built up floors Countertop Measure height of opening from underside of countertop to built up floor If the height is at least 33 84 5 cm the dishwasher will fit into the opening without modification to the countertop or flooring Put wheels L in position 1 and turn the front leveler legs up all the way Add shims as needed in the area shown to bring dishwasher up to proper height Note Shims must be securely attached to floor to prevent their movement when the dishwasher is operated 230 6
14. door spring tension unhook the spring T from the rear leg of dishwasher With a 5 16 nut driver or hex socket remove the screw U from the tensioner V The screw can be put into one of three holes 1 2 3 in front leg of dishwasher The dishwasher is shipped with the screw in the back hole If the door opened by itself move the tensioner to hole 2 or 3 and replace screw Re attach door spring to rear leg Tensioners on both sides of dishwasher should be secured at same holes Grasp the dishwasher door at the edges of the door panel W Tilt dishwasher backwards on wheels X Move dishwasher close to cabinet opening DO NOT PUSH ON FRONT OF PANEL OR ON CONSOLE THEY MAY DENT If dishwasher has a power supply cord insert power supply cord into hole cut into cabinet Check that water line is on the left side of opening and drain hose is near the center of the hole in the cabinet If using direct wire check that it is on the right side of opening Carefully move dishwasher completely into cabinet opening Do not kink or pinch copper tubing drain hose power supply cord or direct wire between dishwasher and cabinet Center dishwasher in opening 18 HELPFUL TIP Built up floors Tilt dishwasher backward to move into opening Once in position support front of dishwasher by lowering or shimming front fee
15. e until smooth 4 Run wire into house wiring junction box Use strain relief method provided with junction box If no strain relief is provided install a cUL listed CSA certified clamp connector for flexible type wire If installing conduit attach a cUL listed CSA certified conduit connector to junction box 5 Run other end of wire through cabinet hole Cable must extend to the left front of cabinet opening Go to step 6 3a Power supply cord method Cut a 1 3 8 cm hole D in right hand cabinet rear or side Optional locations are shown Wood cabinet Sand hole until smooth 4a Install a mating three proung grounding type wall receptacle E in the cabinet next to the dishwasher opening Go to step 6 Water Line HELPFUL TIP Routing the water line through the left side of cabinet opening will make water connection easier 6 Cuta 1 3 cm minimum hole F in left hand cabinet side rear or floor Optional locations are shown The hole F is about 13 s higher than hole C or hole D 11 7 Measure overall length of copper tubing G required Attach copper tubing to water line with manual shutoff valve Carefully feed copper tubing through hole in cabinet copper tubing will bend and kink easily until it is far enough into the cabinet opening to connect it to dishwasher inlet on the front left of dishwasher 8 Turn shutoff valve H to ON position
16. en inner door and tub is equal on both sides If spacing is not equal loosen bracket screws and shift tub Tighten bracket screws If securing to sides of cabinet replace the plastic buttons C WE Check that top of door does not contact screws brackets or countertop If it does dishwasher must be lowered and re leveled Remove paper or towel from dishwasher 24 E CHECK OPERATION 1 Read the Owner s Manual that came with your dishwasher 2 Check that all parts have been installed and no steps were skipped Check that you have all the tools you used 3 Atfuse box or circuit breaker turn on electrical power supply to dishwasher Start dishwasher and allow it to complete the shortest wash cycle After the first two minutes unlatch door wait five seconds then open door Check to see that there is water in the bottom of the dishwasher and that there are no water leaks 4 Check that grounding clip A is attached to the lower panel Place the lower panel B behind the access panel C Some models have insulation D on the access panel which must fall behind the insulation E on the lower panel Hold the two panels together and place them against dishwasher leg Reinstall the screws through the holes in the access panel and the slots in the lower panel Install right side screw first Check that the lower edge of the lower panel contacts the floor Tighten the screws If Dishwasher Does Not
17. g or flexible stainless steel braided fill line 1 3 cm minimum plastic tubing is optional but not recommended A 90 elbow with 3 s 0 9 cm N PT external pipe threads on one end Do not solder within 6 15 2 cm from water inlet valve DRAIN You must Use the new drain hose supplied with your dishwasher If this is not suitable use a new drain hose with a maximum length of 12 feet 3 7 m that meets all current AHAM IAPMO test standards is resistant to heat and detergent and fits the drain connector on your dishwasher Have a high drain loop 30 inches 76 2 cm above the subfloor or floor Connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20 inches 50 8 cm minimum above the floor Use an air gap if the drain hose is connected to house plumbing lower than 20 inches 50 8 cm above subfloor or floor Use Y 1 3 cm minimum I D drain line fittings CABINET DIMENSIONS LT A 24 61 cm All surfaces must be free from intrusions 34 86 4 cm min 3y 8 3 cm 2 5 1 cm 2 5 1 5 1 cm io Dh BMA 25 4 cm zyr Soy 7 cm 8 3 cm 8 3 cm 7 cm g 22 9 cm Cut openings in shaded area of cabinet walls or floor as specified in chart OPENING FOR Water Line Drain Line Direct Wire Power Supply Cord Measured from the lowest point on the underside of countertop
18. lled The location must provide Easy access to water electricity and drain Convenient loading Corner locations require a 2 5 1 cm minimum clearance between the side of the dishwasher door and wall or cabinet Square opening for proper operation and appearance Cabinet front perpendicular to floor Level floor If floor at front of opening is not level with floor at rear of opening shims may be needed to level dishwasher NOTE Shims must be securely attached to floor to _ prevent their movement when dishwasher is being gt operated If dishwasher will be left unused for a period of time or in a location where it may be subject to freezing have it winterized by authorized service personnel Make sure pipes wires and drain hose are within the shaded area See page 9 for dimensions HELPFUL TIP If the floor in the dishwasher opening in uneven example tile flooring only part way into opening you will needed to take special care in measuring dimensions and in leveling dishwasher ELECTRICAL It is the customer s responsibility To assure that the electrical installation is adequate and in conformance will all national and local codes and ordinances You must have 120 volt 60Hz AC only 15 or 20 amp fused electrical supply and connected to an individual properly grounded branch circuit Wiring must be 2 wire with ground and rated for 176 F
19. size to connect your house hold wiring to 16 gauge wiring in dishwasher J Small level K Safety glasses L 90 elbow with 3 s 0 9 cm N PT external threads on one end The other end must fit your water supply line M Flashlight N Teflon tape or pipe joint compound O Shallow pan P Shim stock if instlled with built up floor T raoannondnwnyY In addition for new installations Electric drill Y Hand 1 hole saw bits Small tubing cutter Wire stripper 14 2 screw type clamp if connecting to waste tee V Copper tubing 3 e recommended or flexible strainless steel braided fill line W Clamp connector or conduit connector to fit a s 2 2 cm diametre hole CH YDDO Teflon is a registered trademark of E I Du Pont de Nemours and Company Parts supplied A 2 drain hose clamps 1 large 1 small pl B 2 No ST4 2 X 18 Phillips head screws O C Drain hose Make sure all these parts are included REQUIREMENTS Cabinet Requirements Do not run water drain lines or electrical wiring where they can interfere with or contact dishwasher motor or legs The location where the dishwasher will be installed must provide clearance between motor and flooring Do not install dishwasher over carpeted flooring Protect dishwasher and water lines leading to dishwasher against freezing Damage from freezing is not covered by the warranty Check location where dishwasher will be insta
20. t Les 18 Remove cardboard from under dishwasher HELPFUL TIP It is okay if dishwasher fits tightly into cabinet opening Do not remove insulation blanket it reduces the sound level 19 Align front of dishwasher door panel Y with cabinet doors Z You may need to adjust alignment to look good with your cabinets HELPFUL TIP Prop up one side of frame to hold dishwasher up off floor o when adjusting front legs 19 20 Check that leveling legs AA are firmly against the floor Close and latch the door and place level against the front panel BB Check that dishwasher is plumb Adjust leveling leg or add shims under rear wheel until dishwasher is level NOTE Shims must be securely attached to floor to prevent their movement when the dishwasher is operated Repeat for other side of dishwasher Place level against top front opening of tub CC Check that dishwasher is level from side to side If dishwasher is not level adjust front legs up or down until dishwasher is level C CONNECT DISHWASHER Electrical Connection Check electrical requirements see page 7 You need to Have the correct electrical supply and recommended grounding method Check that power supply is disconnected If you are Use Steps Using a Power Supply cord Water Drain Electrical 20 1 Direct wire method A WARN
Download Pdf Manuals
Related Search