Haier AU182AFNDA Air Conditioner User Manual
Contents
1. During COOL or DRY operation indoor unit may blow out mist This is due to the sudden cooling of indoor air Is power plug inserted Multiple e s there a power failure check Is fuse blown out e s the air filter dirty Normally it should be cleaned every 15 days e Are there any obstacles before inlet and outlet e Is temperature set correctly e Are there some doors or windows left open e Is there any direct sunlight through the window during the cooling operation Use curtain e Are there too much heat sources or too many people in the room during cooling operation Application temp range of air conditioner 7 C 43 C 172. Hints As cold air flows downward in COOL mode adjusting air flow horizontally will be much more helpful for a better air circulation Be careful not to catch a cold when cold air blows downward It is harmful to your health in summer to go frequently in and out of places where temp difference is above 7 C Temp difference of 3 5 C will remove your fatigue More than this unit s load can be reduced and power consumption cut down as well So you d better set a temp diff of 3 5 C between indoor and outdoor temp in COOL mode Operation TIMER operation Set Clock correctly before starting Timer operation referring to page 5 You can let unit start or stop automatically at following times Before you wake up in the morning or get back from outside or after you fall asleep at night TIMER ON OFF 1 After unit start select your desired operation mode Operation mode will be displayed on LCD Power indicator on indoor unit lights up 2 TIMER mode selection Press TIMER button to change TIMER mode Every time the button is pressed display changes as follows Ez OFF eee ON e ak TIMER ON TIMER OFF TIMER ON OFF Select your desired TIMER mode TIMER ON or TIMER OFF ON or OFF will flash 3 Timer setting Press HOUR A V button A Every time the button is pressed time increases 10 min If button is kept depressed time will change quickly V Every time the button is pressed time decreases 10 min If butt
3. If the supply cord is damaged it must be replaced by the manufacturer or its service agentor a similar qualified person The type of connecting wire is HO5RN F or HO7RN F Series 07 09 12 16 18 22 Type 3G61 5mm 2x0 75mm 3G2 5mm 3x0 75mm 4G1 5mm 3 If the fuse on PC board is broken please change it with the type of T 3 15A 250V 4 The distance between the indoor unit and the floor should be more than 2m 5 The wiring method should be in line with the local wiring standard 6 After installation the power plug should be easily reached 10 11 The waste battery should be disposed properly The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance The wiring diagram is attached inside the machine The appliance must be installed on strong enough supporter Parts and Functions Indoor Unit Test running switch manual Used only for test running in cooling when room temp is below 16 C Don t use it in normal operation Emergency switch manual Used when remote controller is lost or defective Unit will run temporarily X Remote signal receiver Inlet grille e Air filter lt Vertical flap Power indicator Timer mode in
4. PM flashes Press A or Y to set correct time Each press will increase or decrease 1min If the button is kept depressed time will change quickly After time setting is confirmed press SET AM and PM stop flashing while clock starts working Hints After replacing with new batteries remote controller will conduct self check displaying all information on LCD Then it will become normal Operation Remote controller s operation When in use put the signal transmission head directly to the receiver hole on the indoor unit The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well Don t throw the controller prevent it from being damaged When electronic started type fluorescent lamp or change over type fluorescent lamp or wireless telephone is installed in the room the receiver is apt to be disturbed in receiving the signals so the distance to the indoor unit should be shorter Loading of the battery Load the batteries as illustrated 2 R 03 batteries resetting key cylinder Remove the battery cover Slightly press W and push down the cover Load the battery Be sure that the loading is in line with the pole request as illustrated Put on the cover again Confirmation indicator In disorderation reload the batteries or load the new batt
5. PM to afternoon 4 Time confirming for TIMER ON After time setting press TIMER button to confirm ON stops blinking While OFF starts blinking Time displayed Unit starts at x hour x min 5 Time setting for TIMER OFF After time setting press SET button to confirm OFF stops flashing Time displayed Unit stops at X hour X min 6 Time confirming for TIMER OFF Follow the same procedures in Time setting for TIMER ON To cancel TIMER mode E Just press TIMER button several times until TIMER mode disappears 11 Operation Comfortable SLEEP JL Before going to bed at night you can simply press olL Tt the SLEEP button and unit will bring you a sound ici sleep in selected mode In COOL DRY mode One hour after SLEEP mode starts temp will become 1 C higher than temp setting After running for another 1 hour temp rises by 1 C further Unit will run for 6 hours then stops automatically Temp is higher than temp setting so that room temp won t be too low for your sleep As shown in Fig 1 SLEEP operation starts SLEEP operation stops Approx 6 hrs Note In AUTO mode unit will run in SLEEP Temp setting Unit stop function according to operation mode In FAN mode comfortable sleep is not Fig 1 available 12 Operation Emergency operation and test operation Emergency Operation Carry out this operation only when the remote controller is defective or lost Wh
6. 3 R1 OUTLET e Warm air comes out when cooling cool air comes out when heating Power Failure Resume to be applied for a necessary situation After the power failure compensation is set if power failure suddenly occurs while the air conditioner is working it will resume the previous working state when the power is supplied again Setting Method When the remote controller is on excluding timer mode and fan mode press the SLEEP button on the remote controller 10 times within 5 seconds and after the buzzer rings 4 times the air conditioner will enter the state of power failure resume Cancel Method Press the SLEEP button on the remote controller 10 times within 5 seconds and after the buzzer rings 2 times the power failure compensation mode will be cancelled Notes When a power failure suddenly occurs during the air conditioner is working after the power failure resume is set if the air conditioner will not be used for a long time please cut off the power supply to prevent its operation from being resumed after the power is supplied again or press the ON OFF button after the power comes again 4 Parts and Functions Operation QD ln IWIN y 15 16 17 18 19 20 21 22 23 24 25 25 SET Used to confirm timer and clock settings 26 HOUR Used to set clock and timer settings 27 LOCK Used to lock buttons and LCD display 26 27 Buttons and display of th
7. Cautions On cooling only unit heating mode is not available After replacing batteries press ON OFF and display becomes as follows Operation mode AUTO Temp No Timer mode No Fan speed AUTO Note The above information is the explanation of the displayed information therefore varies with those displayed in actual operation Operation COOL and DRY operation Recommendations e Use COOL in summer e Use DRY in spring autumn and in damp climate 1 Unit start Press ON OFF button unit starts Previous operation status appears on display Not Timer setting Power indicator on indoor unit lights up 2 Select operation mode Press MODE button For each press operation mode changes as follows AUTO COOL DRY FAN Unit will run in operation mode displayed on LCD Stop display at your desired mode 3 Select temp setting Press TEMP button A Every time the button is pressed temp setting increases 1 C V Every time the button is pressed temp setting decreases 1 C Unit will start running to reach the temp setting on LCD 4 Fan speed selection Press FAN button For each press fan speed changes as follows COOL operation starts when room temp is higher than temp setting Ultra low air flow Unit runs at the speed displayed on LCD 5 In DRY mode when room temp becomes 2 C higher than Temp setting 2 c Sing temp setting unit will run intermittently at LO speed Te
8. SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL ASO72AZNBA AU072ABNCA HSU 07CG03 R1 ASO92ZAMNBA AU092ABNCA HSU 09CG03 R1 AS122AYNBA AU122ABNCA HSU 12CG03 R1 AS162ATNBA AU162AFNBA HSU 16CG03 R1 AS182ASNBA AU182AFNDA HSU 18CG03 R1 AS222AJNBA AU222AHNBA HSU 22CG03 R1 Please read this operation manual before using the air conditioner No 0010544375 Contents Calon ese se lt 1 2 Parts and TunCtiOnS s6 s ie ee 3 5 C DCTALION eser secs ee ete ee 6 13 Maintenance oer e ec ereecrceccctececesccseceseseesecesenes 14 16 Trouble shooting 2eee ee eee eee e ee ec eee eeeeeeees 17 Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use please make sure it s inoperative and safe Unplug the air conditioner in order to avoid the risk of child entrapment It must be noticed that air conditioner system contains refrigerants which require specialized waste disposal The valuable materials contained in a air conditioner can be recycled Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question Please ensure that the pipework of your air conditioner does not get damaged prior to being picked up by the relevant waste disposal center and contribute to environmental awareness by insisting on an appropriate anti pollution method of disposal Disposal o
9. dicator Use remote controller to adjust up and down air flow Don t adjust it manually Lights up when Timer operation is selected Lights up when unit starts For models AS072AZNBA AS092AMNBA AS122AYNBA HSU 07CG03 R1 HSU 09CG03 R1 HSU 12CG03 R1 Inlet grille Air filter Vertical flap Power indicator Timer mode indicator Use remote controller to Lights up when unit adjust up and down air flow starts Don t adjust it manually Lights up when Timer operation is selected Lights up during For models AS162ATNBA AS182ASNBA HSU 16CG03 R1 HSU 18CG03 R1 Inlet grille f Air filter Vertical flap Use remote controller to adjust up and down air flow Don t adjust it manually For models AS222AJNBA HSU 22CG03 R1 Operation mode indicator compressor running A beeping sound is generated when a signal from remote controller is received X Operation mode indicator Lights up during compressor running Signal Receiving Window Running Indicator Timer Mode Indicator Power Indicator Parts and Functions Outdoor Unit For models AU072ABNCA HSU 07CG03 R1 CONNECTING PIPING AND TONER ELECTRICAL WIRING HSU 09CG03 R1 AU122ABNCA INLET x HSU 12CG03 R1 g DRAIN HOSE For models AU162AFNBA HSU 16CG03 R1 AU182AFNDA HSU 18CG03 R1 AU222AHNBA HSU 22CG0
10. e remote controller Mode display AUTO COOL amp DRY 6 FAN SWING display FAN SPEED display l l AUTO LO MED HI liii CI Mii ece HEALTH display SLEEP display TIMER ON display AUXILIARY HEAT display SWING 0 11 15 16 17 18 19 20 21 22 23 24 2 3 4 5 6 LOCK display 7 8 9 1 MODE Used to select AUTO COOL DRY HEAT and FAN CLOCK Used to select your desired temp TIMER Used to select TIMER ON TIMER OFF RESET Used to reset the controller back to normal condition CODE Used to select code A or B with a press A or B will be displayed on LCD please select A without special explanation CODE display SIGNAL SENDING display POWER SOFT display TEMP display CLOCK display TIMER OFF display TEMP Used to select your desired temperature FAN Used to select fan speed POWER ON OFF Used for unit start or stop SLEEP Used to select sleep mode NOTE 1 The following functions and related displays are not available HEALTH display AUXILIARY HEAT display POWER SOFT display 2 If the Air condition don t have the function press code B can cause it not available 3 Cool only unit do not have functions and displays related with heating Clock set When unit is started for the first time and after replacing batteries in remote controller clock should be adjusted as follows Press CLOCK button AM or
11. en the emergency operation switch is pressed a Pi sound starts once which means the start of this operation e In this operation it is not possible to change the settings of temperature and air flow speed it is also impossible to do an operation by the timer Follow the requirements below Room Designated More than 23 C 26 C X If an air conditioner is a model cooling Cooling when the room temperature at the start of operation is above 23 C Test operation Use this switch in the test operation when the room temperature is less 16 C do not use it in the normal operation Continue to press the test operation switch for more than 5 seconds After you hear the Pi sound twice release your finger from the switch the cooling operation starts with the air flow speed setting Hi Removal of the restriction of emergency or test operation e Press once more the emergency operation switch or manipulate through the remote controller a Pi sound causes the restriction of emergency or test operation to be removed e When the remote controller is manipulated for the removal then the selected operation by the remote controller 13 Q Maintenance X Different models have different appearance Cut off power supply before cleaning wipe unit casing with soft cloth In case of heavy stain clean it with n
12. eries after 6 mins Note Use two new same typed batteries when loading If the remote controller can t run normally or doesn t work at all use a sharp pointed item to press the reset key Hint Remove the batteries in case unit won t be in usage for a long period If there are any display after taking out just need to press reset key 6 Operation Auto run Fan operation 1 Unit start Press ON OFF button unit starts Previous operation status appears on display Not Timer setting Power indicator on indoor unit lights up 2 Select operation mode Press MODE button For each press operation mode changes as follows AUTO COOL DRY FAN Unit will run in selected mode Stop display at W AUTO or FAN 3 FAN Press FAN button For each press fan speed changes as follows AUTO LO MED HI E HII S86 Unit will run at selected fan speed Note AUTO is not available in FAN mode Adjust air flow direction if necessary referring to page 9 Hints Enjoy yourself by just a gentle press 4 Unit stop Press ON OFF button Only time remains on LCD All indicators on indoor unit go out Vertical flap closed automatically Remote controller can memorize settings in each operation mode To run it next time just select the operation mode and it will start with the previous setting No reselecting is needed TIMER ON OFF needs reselecting
13. eutral detergent squeeze water in the cloth wipe off the detergent on unit casing completely C Don t use water to wash unit casing please use dry cloth Don t use glass cleanner or cloth soaked with chemicals Air Filter 2 Remove air filters Push up the filter s center tab 3 Clean the filter slightly until it is caesura of Use a vacuum the stopper Remove it by a i cleaner to remove pulling down dust or wash the ne filter with water ul 4 Attach the filters After washing wanes Air Filter dry the filter Attach filter behind the stopper so that completely in the shade the Front indication is facing to the front Make sure that it is completely behind the stopper otherwise 5 Close the inlet grille problems might occur 14 Maintenance Replacement of Electrostatic Filter 1 Detach the Air filters 2 Detach the Electrostatic Filters a AY Be careful 3 Replace the old filter with new one into the frame Pull up the hook to the designated direction Emea HEA White side should be up side 4 Open the frame of the filter 5 Attach the Electrostatic Filters 6 Attach the Air Filters Close the inlet grille Some of the models may not have the frame of the filter If Electrostatic Filter can no longer be used please buy a n
14. ew one instead 15 Maintenance Better use of air conditioner Proper room temperature Cleaning of the air filter Once every two weeks Cc gt LS Closing of doors and windows during operation ALL ono eg sae cap Such as food preservation plant cultivation or animl breeding Trouble shooting The system does not restart When unit is stopped it won t restart immediately immediately until 3 minutes have elapsed to protect the system When the electric plug is pulled out and reinserted the protection circuit will work for 3 minutes to protect the air conditioner During unit operation or at stop a swishing or gurgling noise may be heard At first 2 3 minutes after unit start this noise is more noticeable This noise is generated by refrigerant flowing in the system Normal f e During unit operation a cracking noise may performance 0 be heard This noise is generated by the inspection casing expanding or shrinking because of temperature changes Should there be a big noise from air flow in unit operation air filter may be too dirty e This is because the system circulates smells from the interior air such as the smell of furniture cigarettes Smells are generated Mist or steam are blown out
15. f the packaging of your new air conditioner All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to the environment The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service The wrapping bag made of polyethylene and the polyethylene foam pads contain no fluorochloric hydrocarbon All these valuable materials may be taken to a waste collecting center and used again after adequate recycling Consult your local authorities for the name and address of the waste materials collecting centers and waste paper disposal services nearest to your house Safety Instructions and Warnings Before starting the air conditioner read the information given in the User s Guide carefully The User s Guide contains very important observations relating to the assembly operation and maintenance of the air conditioner The manufacturer does not accept responsibility for any damages that may arise due to non observation of the following instruction e Damaged air conditioners are not to be put into operation In case of doubt consult your supplier e Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User s Guide e Installation shall be done by professional people don t install unit by yourself e For the purpose of the safety the air conditioner must be properly gro
16. mp setting On a will run in mild DRY mode Hints regardless of FAN setting Remote controller can memorize each operation status When starting it next time just press ON OFF button and unit will run in previous status 8 Operation 5 Air flow direction adjustment After operation mode is selected vertical flap will open automatically according to the mode Referring to the Fig COOL Level About 10 Up and down Use remote controller Left and right air flow adjustment Press SWING button vertical flap will move within manual the range shown in the Fig Press SWING button Move the horizontal blade by a knob on air stop it at a fixed position conditioner to adjust left and right direction referring to Fig orcas About 102 l i COOL About 45 Cautions Cautions It is advisable not to keep vertical flap at downward position for a long time in COOL When humidity is high condensate water might occur at air outlet if all horizontal OLE MOS OR RNISe COndeneale louvers are adjusted to left or right water might occur 6 Unit stop Press ON OFF button Only time remains on LCD All indicators on indoor unit go out Vertical flap closes automatically Cautions Unit won t restart until 3 minutes have elapsed due to system protection
17. on is kept depressed time will change quickly Time will be shown on LCD It can be adjusted within 24 hours 4 Confirming your setting After setting correct time press SET button to confirm ON or OFF stops flashing Time displayed Unit starts or stops at x hour x min TIMER ON or TIMER OFF Timer mode indicator on indoor unit lights up To cancel TIMER mode Just press TIMER button several times until TIMER mode disappears Hints After replacing batteries or a power failure happens Time setting should be reset Remote controller possesses memory function when use TIMER mode next time just press SET button after mode selecting if timer setting is the same as previous one 10 Operation TIMER ON OFF 1 After unit start select your desired operation mode Operation mode will be displayed on LCD Power indicator on indoor unit lights up 2 Press TIMER button to change TIMER mode Every time the button is pressed display changes as follows ie om id ON a ek i TIMERON TIMER OFF TIMER ON OFF Select TIMER ON OFF ON will flash 3 Time setting for TIMER ON Press HOUR button A Every time the button is pressed time increases 10min If button is kept depressed time will change quickly V Every time the button is pressed time decreases 10min If button is kept depressed time will change quickly Time will be shown on LCD It can be adjusted within 24 hours AM refer s to morning and
18. unded in accordanc with specifications e Always remember to unplug the air conditioner before openning inlet grille Never unplug your air conditioner by pulling on the power cord Always grip plug firmly and pull straight out from the outlet e All electrical repairs must be carried out by qualified electricians Inadequate repairs may result in a major source of danger for the user of the air conditioner e Do not damage any parts of the air conditioner that carry refrigerant by piercing or perforating the air conditioner s tubes with sharp or pointed items crushing or twisting any tubes or scraping the coatings off the surfaces If the refrigerant spurts out and gets into eyes it may result in serious eye injuries Cautions e Do not obstruct or cover the ventilation grille of the air conditioner Do not put fingers or any other things into the inlet outlet and swing louver e Do not allow children to play with the air conditioner In no case should children be allowed to sit on the outdoor unit Specifications e The refrigerating circuit is leak proof The machine is adaptive in following situation 1 Applicable ambient temperature range ingest Maximum D B W B 32 C 23 C Minimum D B W B 18 C 14 C Cooling Maximum D B 43 C Outdoor _ Minimum D B 15 C Maximum D B 27 C Indoor Minimum D B 15 C Heating Maximum D B W B 24 C 18 C Outdoor Minimum D B 20 C 2
Download Pdf Manuals
Related Search