Graco Inc. 258740 Paint Sprayer User Manual
Contents
1. The appliance door is not shut properly Close the door firmly and try the machine again The Start Cancel button has not been pressed for at least 3 seconds Press and hold the Start Cancel button until the machine starts to operate The cold water supply tap is not turned on Aquarius only Wash indicator light is Flashing on the control panel Aquarius only H20 is shown in the display Aquarius only Have you selected Time Delay see Programmes and Option Modifiers The Start Cancel button has not been pressed for at least 3 seconds Press and hold the Start Cancel button until the machine starts to operate The machine has failed to take in water see Installation Is the Wash indicator light flashing Aquarius only Is H20 shown in the display Aquarius only Check that Both of the cold water inlet hoses are connected to the cold water supply tap using the Y piece connector The hoses are not kinked The cold water supply tap is turned on Ensure that it is turned fully on The water pressure is sufficient see Technical Details Chart The inlet filters are not blocked Turn off the water unscrew both fill hoses at the back of the appliance then remove and clean the filters Note Modern machines use less water and the water taken into the machine is automatically adjusted depending on the load in the drum For this reason you may not always be able to see water in the dru2. two bolts two washers two rubber grommets and two nylon spacers The machine is not level see Installation Adjust the feet so that the machine stands firm on the floor ie it does not rock and ensure the machine is level from front to back and from side to side The machine is closed in between furniture cabinets and the wall see Installation Perhaps the machine was attempting to spin an unbalanced load Try the machine again with a different wash load When you sort your laundry into wash groups check all loose items such as coins are removed from the laundry Check the drum at the end of each cycle and remove any loose items coins etc Note Super Silent refers to wash sound level only there will always be some motor and drum noise during spin from behind or underneath Check each end of both cold water inlet hoses ensuring connections at both ends are tight and not leaking see Installation Check all connections on the Y piece connector to ensure they are tight and not leaking see Installation Depending on the installation method used see Installation Check that the drain hose is firmly secured to the undersink U trap or the drain hose is positioned correctly into the standpipe Check that your water pressure is within limits see 7echnica Details Chart IF too high try turning the cold water supply tap down slightly and try the machine again see nsta ation fro
3. your machine over the hole Repeat steps 1 to 4 to remove the second transit bolt Packaging materials are not children s toys Location Where you install your machine will affect its performance For your safety and to comply with electrical regulations seek professional advice if you want to install your machine in a bath or shower room e Make sure that the electrical socket and water taps are easily accessible You should switch off the machine s electrical and water supplies when you are not using it for extended periods e Make sure that you allow enough space for the machine Select a space at least 60cm wide 60cm deep and 85cm high Also leave enough space to open the door fully so that you can load and unload it easily e Where possible the machine should be positioned ona solid floor to minimise vibration Take care when you move the machine not to rip any floor coverings The weight of the machine may cause indentations in some floor coverings the transit fixings are fitted to ensure that your machine is undamaged during delivery both of the transit fixings MUST BE removed before using the machine be sure to remove TWO bolts TWO washers TWO rubber grommets and TWO nylon spacers not doing so will lead to excessive vibration movement of the machine and could eventually lead to internal damage the majority of problems with noisy machines are due to the transit fixings not bein
4. Auto will appear in the display e Timed drying Press the Drying Times button until the required time is shown in the display 8 Start the programme by pressing the Start Cancel button for at least 3 seconds The Door Locked indicator will light up e To stop change a programme once the machine has started Press the Start Cancel button for 3 seconds Select Pump Out EJ on the Programme selector dial When the machine has finished emptying Turn the Programme selector dial to the new programme required you may need to add detergent Check optional wash feature s wash temperature and drying time selected in STEPS 5 6 and 7 change if necessary Press the Start Cancel button to start the new programme 9 During the programme indicator lights will show you what stage in the programme the machine has reached Wash Rinse amp Spin Final Spin Dry cmm ss 10 A short time after the programme has finished the een we Door Locked indicator will go em out You can open the machine door and remove your laundry 11 Switch the machine off by pressing the On Off button Do not allow children to play with the machine or tamper with the controls Do not overload the machine This may damage the laundry and reduce the quality of the wash The maximum load Cotton is 6kg WASH 5kg DRY Do not try to open the dispenser drawer during any programme Do not try to op
5. Whichever drainage method you use make sure that the hooked end support is fixed level to or above the Plumbing Indicator Line see Description page 2 We recommend one of the following Standpipe method 1 Make sure the standpipe height is a minimum 500mm up to Geet a maximum 1200mm fromthe B W Floor minimum 500mm maximum 200mm 2 Insert the drainage hose approximately 100mm into the standpipe Under sink method 1 Cut off the blocked end of the under sink drainage unit or remove the blanking plug if fitted 2 Fix the hooked end support a minimum of 800mm from the floor 3 Use a hose clip eg a jubilee clip to securely attach the grey drainage hose end to the under sink drainage unit minimum 800mm from floor Did you know Electrical connections Before plugging the appliance into the mains socket make sure that e the socket is earthed and in compliance with the applicable law e the socket is able to sustain the appliances maximum power load indicated in the Technical Details table see page 20 e the supply voltage is included within the values indicated in the Technical Details table see page 20 e the socket is compatible with the machines plug IF this is not the case replace the socket or the plug ensuring a 13A fuse is fitted The machine should not be installed in an outdoor environment not even when the area is sheltered bec
6. e7Su 5 Stand the machine upright We recommend that a second person helps to raise and lower the machine sounjee j ued ouq3uoo 3 Carefully lay the left side of the machine down onto the top cap SISIJIPOW uoin do pue s uliueuBo d We recommend that a v g second person helps to raise Continue to read the rest a and lower the machine of these instructions rs 9 2 carefully the following 35 pages contain important 26 information on installation and troubleshooting 2 O D Oo 95 a e Protect the environment please dispose of the gt 2 packaging material carefully and considerately lt 5 D O Buryooysajqnouy BuoumM Buiyzewos 3IAJ8S Installation Remove the transit fixings IMPORTANT Follow these instructions to remove the TWO transit fixings see Description for location Situated one either side of the rear panel BOTH transit bolts MUST be removed before use asan cans Failure to do so may cause damage to your machine It is important the TWO transit fixings come out intact Be sure to remove TWO bolts TWO washers TWO rubber grommets and TWO nylon spacers see pic 1 Unscrew the bolt using a 13mm spanner 2 STOP when 3 threads can be seen Did you know 3 Hold slide sideways and pull to remove 4 For safety insert one of the the plastic covers supplied with
7. the wash cycles Error messages will be displayed on the control panel to indicate there is something wrong The error message displayed is dependent upon which machine you have Error message Wash indicator light is flashing on Aquarius models OR H20 flashing in the display on Aquarius models Door Locked indicator light is flashing on Aquarius models OR The display shows door on Aquarius models This indicates that the machine has failed to take in water see nstallation Check that e both of the cold water inlet hoses are connected correctly to the cold water Supply tap using the Y piece connector e the cold water inlet hoses are not kinked e the cold water supply tap is turned on Ensure it is turned fully on e the water pressure is sufficient see 7echnical Details Chart This indicates that the door is not closed properly e Close the door firmly and try the machine again gd SJSIJIPOW saunjee uolzeyjeqsu p uie dx3 sau 3uo2 uoigdiuos q O pue aue sau Bu 3 q uodo pue jaued joujU07 sjaqe7 yseM wo sawweuboud S5ueu quIle8lN Aupune pue 3IApV pue suoiqnededd Buryooysajqnouy BuouMm Buiuag uijos 3IAJ 8S Service 5057720 19 00 06 2006 SIMLEX Four Ashes Wolverhampton Before calling the Service Centre Spare Parts e Use the troubleshooting guide to see if you can This is a complex machin
8. to condense the moisture extracted from the load Check that e Both of the cold water inlet hoses are connected to the cold water supply tap using the Y piece connector e The inlet hoses are not kinked e The cold water supply tap is turned on Different load types need different heat settings Some need HIGH heat some need LOW heat Check that e HIGH heat option has been selected if you are drying Cottons Different load types need different drying times Check that e The Drying time selected was sufficient for the load Note Your machine contains an out of balance spin protection device if the out of balance is too great the machine automatically spins at a lower speed Check that the load was spun correctly at the and of the wash cycle before the machine advanced into the drying cycle then try another rinse and spin and repeat the drying cycle e A 20 minute Cool Tumble period is included at the end of the drying cycle Always allow the machine to complete the full drying cycle to ensure this cool tumble period occurs e This is normal and is not a fault The machine may sometimes spin during the drying cycle to improve drying efficiency e This is normal and is not a fault You must always return the Drying Times dial manually to the Off position at the end of each drying cycle Section 3 Specific Error Messages on the Control Panel Your machine carries out automatic checks at various stages of
9. wwepod eied silu ulds jse4 Sd O a ulds Mo s p XIN D Aejaq all sasealg sonpey seseal onp ti 008 cZ 0 Udy pue s sun N om s jdwoo wwepod ped siy uldS 9 asuly SRY qu 5 auinbai NOA ss u up JO A 9 y soouo LO pue wweipord Bul up one ue 29 95 luo Sniuenby 184 MOT s3 n ulu s O 40 AJP O YSIM NOA swa BU JO GuNyeJedwe ge u HO H suollo9 WW Aejaq aul H YIH Huq H uBiH Buruq jeloads eI Gle 14 pue w Bu up y 199 9S snuenby 9 snuenby burg N Ka HIIS OOM 100 AJUO S9 eO 9q T pinbq 1no0jo9 joany Aejoq wlL OOr ELUJON 0S 0 Y GZ yseM PUBH se pajege swa a ed 9p JO J0 9 llu 6 v ysempuey V 7 O YSEMPUEHAIIS IOOM JOU 5 SsoluqeJ pexiy T pinbi 1n0j09 joany Aejaq ati 008 1467 08 0 og pexilw p ljios l uBi Jo auuWeG0Jd ys 14 1 oys A V ysey ise4 Oe y O AS _ p yaq Aejeq etl PlOH SUlY PIOH suli 008 JewJoN G 0 oe ajqeysem SUIYOeW se paljaqe syjusoweb yIIS 104 aiqeysey euryoey FOEN r N P yreuu oo Aq p A0Jdde Ajanisnjoxe s u guueB6 INOA JOOM USEMPUeH 5 yaq Aejaq Ou 009 JewJoN qr 0 Or YUIUS JOU JIAA JEU OOM yYSEM PUCH JO ajOAo jeloeds v penoiddy yewjooy pjoy Or H que g q Sul JENS Suu OSUIY BAXF EAS UJI SOINIXILW Gl pue SOI J0v 9 sol 8ulu S p no joo _ D INO OD jony PIOH sulii S se 10 onp ti PIOH suli s se O onp ti 008 JPLLLION GO L 3 Or SO
10. 30am to 12noon www hotpointservice co uk Republic of Ireland 0818 313 413 www hotpoint co uk Indesit Company UK Limited Morley Way Peterborough PE2 9JB
11. K Hotpoint OUR IDEAS YOUR HOME Instructions for Installation and Use 6kg Washer Dryer Aquarius Aquarius To the Installer Before installation fill in the product details on the back cover of this book The information can be found on the rating plate To the User You must read these instructions prior to installing and using the appliance and then retain them for future reference Description Dispenser drawer Control panel e Varies by Model Please record the Model number and Serial number of your machine on the back cover of this book for future reference The Serial number can be found on the inside door trim Interlocking door and release lever Cold water inlet points DO NOT remove either of the Front adjustable feet and attached fill hoses attached fill hoses OR the Y piece blue connectors connector even if you have both Hot and Cold water supplies see Drainage hose Mains cable page 7 Zs 2 Hooked end support n Two transit fixings BOTH must be removed BEFORE you use your machine see page 6 Plumbing indicator line Rating plate Y piece connector Back feet Contents WASHER DRYER Description 2 o O Wash Labels Explained 4 T oO Installation 5 8 Unpacking Remove the transit fixings Location D 3 3 Levelling N Water connection Drainage connection Electrical connection Be
12. PPLY ZT Ta UY piece connector Why LR KS Cold water fill hose Blue Connectors Did you know K Hotpoint 1 Screw the Y piece connector onto the cold water supply until tight 2 Fit a 3 4 sealing cap to the hot water supply to prevent unused supply leaking 3 Turn ON the COLD water supply tap and check for leaks tighten if necessary 4 Leave the unused HOT water supply turned OFF We recommend fitting a 3 4 sealing cap to the hot water supply tap if present to ensure there are no leaks Sealing caps can be purchased from Hotpoint Service on 08709 077 077 or all good DIY and Plumbing outlets Benefits of cold fill e Modern detergents are designed to give the best cleaning results at low temperatures Biological detergents contain enzymes which are active between 30 C and 53 C giving greater results at lower temperatures e Cold water relaxes fabrics whilst hot water can Seal in stains e Improved stain removal with cold water e The most commonly used programme at present is 40 C which will take on cold water even if hot and cold were available e You can heat the water required to finish the wash cycle which makes it more economical than taking water heated in a tank by an immersion heater or gas boiler Hints and tips Make sure there are no kinks or bends in the hose The water pressure at the supply tap must be within the values indicated in the Technical De
13. Two bars mean the clothes need a mild wash action but can be spun and rinsed normally Such items should not be wrung out by hand IF the tub contains a hand wash the item on a Hand Wash programme A triangle means that you can safely use a cold dilute solution of bleach A triangle with a cross over it means the item cannot be bleached A circle inside a square means you can tumble dry the garment The dots indicate temperature one dot for lower heat two dots for higher heat A cross over this symbol shows you should not tumble dry the garment A circle means the garment is suitable for dry cleaning A letter inside the circle is to tell the dry cleaner which chemical wash and method to use Installation K Hotpoint Read these instructions carefully the following 4 Remove the pages contain important information on installation polystyrene base and suggestions on how the appliance works Unpacking uoigdiuos q 1 Using scissors cut carefully along one corner post to remove the film sau q3uo2 his is a part of the polystyrene base and should have stayed intact when you removed the base Vif it has broken off and IMPORTANT check is still in the machine when unpacking your remove it while the machine machine is still laying on its side on the top cap p uie dx3 Sj qeq YSeM 2 Lift off the polystyrene top cap and remove the four corner posts uo ze
14. abel on items when choosing the wash programme e Wash non colourfast items or really dirty items separately as they may affect other laundry Did you know that with Hotpoint and Ariel you ll get the best washing results F Certain laundry products work better in some machines than others At Hotpoint we know this is true because we ve done the research to prove it We used real everyday clothes and ran tests to find out which washing powder works best with Hotpoint The results proved that Hotpoint and Ariel produces the best washing results on all your clothes Ariel can meet all your laundry needs It is available as a biological powder for everyday wash loads Colour powder to keep your clothes staying brighter for longer and a Non Bio powder for when you need brilliant cleaning but are concerned about sensitive skin Did you know undissolved detergent left in the drawer or on clothes can be due to incorrect dosing or using the incorrect dispensing method CHECK the detergent manufacturers instructions on the pack for dispensing and dosage advice 17 uoigdiuos q sau qauoo m gt o 5 o s un3e 3j uo ze e4Su sjaqe7 ysem j ued ou3uoo S4 JIPON uoi d 0 pue sawweubo0ud s u u 4 q sueu gzuiewN Ma W lfi pue oue7 3IApV pue suolg ne2 Jd Buryooysajqnouy BuoumM Buiyzewos BDIAIIS Care and maintenance Cleaning Un
15. achine on by PEE Cance pressing the On Off button 2 Sort your laundry into groups by washcare labels Load the machine Close the machine door by pushing it until it clicks 3 Add detergent and fabric conditioner to the dispenser drawer Refer to detergent manufacturer s dosage instructions 4 Turn the programme n selector dial to the required programme 5 Select any optional wash feature s see Option Modifiers you require by pressing the appropriate buttor s Indicator lights will show what you have chosen amp Drying High Heat ammp Reduce Creases mme_ Rinse Hold CEED Time Saver amm Extra Rinse 6 Reduce the programmes wash temperature Aquarius only Turn the Variable Temperature dial to the reduced temperature you require When the programme has Finished return the dial to its maximum setting c 95 I s No Heat 70 D 30 1 60 40 50 Aquarius only Press the Variable Temperature button until the required temperature shows in the display Each press will reduce the wash temperature by 5 C 10 7 Select drying time or level if available on your model Aquarius only Timed drying Turn the Drying Times dial to E m emm the required time ash O by When the programme has Finished return the dial to its OFF position Aquarius only choose either e Auto Sensor Dry Press the Drying Times button once
16. ance when cleaning it and during all maintenance operations e This machine should only be used by adults and in accordance with the instructions e Do not overload or underload the machine In addition to reducing the quality of the wash this may also damage your laundry and the machine e Do not pull on the power supply cable to unplug the appliance from the electricity socket Pull the plug out e Do not open the machine door while the appliance is in operation e Do not open the detergent dispenser while the appliance is in operation e Never force the machine door this could damage the safety lock mechanism designed to prevent any accidental opening e Turn off the water tap after every wash This will limit the wear of your appliances water system and also prevent leaks e Inthe event of a malfunction do not under any circumstances touch internal parts in order to attempt repairs e Always keep children well away from the appliance while in operation Do not let children play with the machine or tamper with the controls e The appliance door tends to get quite hot during the cycle e Should it have to be moved proceed with the help of two or three people and handle it with the utmost care Never try to do this alone because the appliance is very heavy e Before loading your laundry into the machine make sure the drum is empty e Check the water fill hose at least once a year If you see any cracks replace it immedia
17. aundry e Where the drying only option is regularly used do this on a monthly basis 18 Moulded plug The plug must not be used without the fuse cover in place If a replacement fuse holder cover is required it must be of the same colour coding or wording as shown on the base of the plug Replacements are available from authorised dealers Changing the plug The wires in the power cord are coloured in accordance with the following Green and Yellow Earth wire to terminal marked E symbol or coloured green and yellow 13A ASTA approved Blue Neutral wire to TUSSA BS PDE terminal marked N or coloured black Brown Live wire to terminal marked L or coloured red Cord clamp If the plug being replaced is a non rewirable type then the cut off plug must be disposed of safely DO NOT leave it where it can be inserted into a socket and create a shock hazard The power supply cord should be checked periodically and replaced by a cord specially prepared for this machine and fitted only by authorised technicians see Service Replacement power cords can be purchased at an extra cost from our Genuine Parts and Accessories department or authorised dealers The manufacturer denies any responsibility should any of these rules not be followed If in doubt about any of the above consult a qualified electrician Precautions and advice General safety e Unplug your appli
18. ause it may be very dangerous to leave it exposed to rain and thunderstorms When the machine is installed the mains socket must be within easy reach and should be connected to a suitable electrical supply Do not use extensions or multiple sockets The power supply cable must never be bent or dangerously compressed The power supply cable must only be replaced by an authorised serviceman The company denies all liability if and when these standards are not respected Before you start using your machine The first wash cycle Once the appliance has been installed and before you use it for the first time run a wash cycle without detergent and no laundry This will check your installation connections and drainage and will thoroughly clean the interior before you carry out an actual wash programme on your laundry This will take approximately 21 2 hours to complete Run the 95 White Cotton programme B without laundry and without detergent During this cycle check for any leaks from under the machine If present ensure all hoses are securely tightened itis very important to ensure that your hoses or cables are not kinked or squashed as this can lead to your machine failing to fill or empty the water itis very important to respect the dimensions given within the drainage connection methods see above if using the undersink drainage method remember to cut off the blocked end or remove the blankin
19. cantly lower than a conventional machine e Aquarius only Display IF time delay is selected this shows the time remaining until the start of the wash programme in hours counting down each hour IL also displays time to end of the wash programme in hours and minutes counting down each minute Please note time can go up as well as down depending on load absorbency load size and water temperature Note We recommend that if you use colour catcher sheets in your appliance that these only be used inside a wash bag as otherwise they can affect the performance of your machine Did you know when an option button is selected the corresponding light is illuminated if the option selected is incompatible with the programme selected the button will flash and the option will not be enabled if you set an option that is incompatible with an option selected previously only the last option selected will be enabled 15 sounjes4 uo qejie3suj p uie dx3 s3au 3uoo uo 3dii5s q D s qe1 use wo j ued ou3uoo S4 JIPON uoin do pue s wWwe eJoJd sdueusejuieyW Aupune pue 3IApV pue suolg ne2 Jd Buryooysajqnouy BDIAIIS BuoumM Buiyzewos s u u 4 q pue aue7 Option Modifiers and Special Features Automatic features Unbalanced load detection The machine has an inbuilt feature to prevent it from spinning too fast with an unbalance
20. d load When an unbalanced load is detected the machine will attempt to redistribute the load in order to balance it evenly to achieve full spin speed IF this is not possible and an unbalanced load remains the spin speed will be reduced depending on the amount of unbalance detected This is to prevent the machine from damaging itself or its surroundings and to prevent excessive noise from the machine If the spin result is unsatisfactory following a reduced spin speed attempt to rectify the unbalanced load then on completion of the programme the load can be redistributed evenly in the drum by hand Select a spin cycle Note Do not attempt to spin heavy or absorbent single items as the machine cannot distribute these evenly IF you need to wash a single item you will need to add some other items as ballast to allow the machine to distribute the load evenly throughout the drum No water detection The machine will automatically detect if it cannot take in water and will notify you by Aquarius models flashing the Prewash light Aquarius models flashing H20 on the digital display IF this occurs please check the appliance is plumbed in correctly with both fill hoses fitted to the cold water supply using the Y piece connector see Installation Water connection Energy saving and water levels Modern machines are designed to be as environmentally friendly as possible To achieve this water levels are k
21. e Repairing it yourself or solve the problem yourself see Troubleshooting having a non authorised person try to repair it could e f not turn off the machine and call the Service cause harm to one or more persons could damage Centre closest to you the machine and could invalidate the spare parts warranty You will be charged for a service engineers visit if a Call an authorised technician if you experience problems problem with your machine is caused by incorrect while using the machine installation or misuse The spare parts have been designed exclusively for this appliance and not for other uses Key Contacts After Sales Service Over 1100 trained specialists directly employed by us ensure that you can have complete confidence in both the appliances and services we offer Repair Service and Information Help Desk UK 08709 066 O66 Monday to Friday 8am to 7 30pm Saturday 8 30am to 5 30pm Sunday 9 30am to 3 30pm www hotpointservice co uk Republic of Ireland 0818 313 413 Note Our operators will require the following information Model number _ _ _ Serial number __ _ Date ofpurchase Model number and Serial number can be found on the inside of the door Extended Warranties UK 08709 088 088 Monday to Sunday 8am to 8pm www hotpointservice co uk Republic of Ireland 0123 002 333 Genuine Parts and Accessories UK 08709 077 077 Monday to Friday 8 30am to 5pm Saturday 8
22. e dial to 95 If the dial is left at maximum 95 the wash temperature will be the maximum for the chosen programme Aquarius only each press of the button will reduce the wash temperature by 5 C The new wash temperature will be shown in the display IF you press again after OFF has been displayed the machine will revert to the original higher temperature e Variable Drying Times Use this option to select the drying options required see Setting drying programmes Aquarius only turn the dial to the required drying programme time in minutes If this is selected before the wash programme is started the machine will carry out a wash and dry cycle When the programme has finished reset the dial to the Off positions Aquarius only each press of the button allows you to select between Auto drying and a drying time in minutes If this is selected before the wash programme is started the machine will carry out a wash and dry cycle 14 Option Modifiers and Special Features Hotpoin Special features Not all special Features can be used on all programmes see Programme Table for option availability e Fast Wash The Fast Wash programmes are designed for lightly soiled loads delivering quick results for smaller loads using less energy For loads with stains or increased soil levels which require deeper cleaning use the standard or intensive wash cycles e Wash amp Dry On most prog
23. en the machine door when the Door Locked indicator is lit Drying Hotpoin Setting drying programmes Independent drying only programme 1 Remove the wet laundry and in drum dosing ball if used until the correct Drying Weight Load see Drying table below is left in the drum Close the door until it clicks shut 2 Turn the programme selector dial to drying programme M see Programme table 3 Select HIGH HEAT see Option modifiers if drying cottons by pressing the Drying High Heat option button the corresponding light will show selection 4 Set the required drying time or autodry option see Drying option below 5 When all selections have been made press the Start Cancel button The door will lock 6 A short time after the programme has finished the Door locked indicator light will go out and the door can be opened Drying option e Timed Drying programmes Where you can select the length of the drying time suitable for your load Aquariust Press the Drying Times button twice and 3 will appear in the display indicating 3 hours drying time Each subsequent press of the Drying Times button will reduce the drying time shown in the display in 30 minute increments until 1 1 hour is displayed Pressing the Drying Times button again after 1 is displayed cancels the drying programme Off will appear in the display no drying programme is selected Aquarius Use the Drying T
24. ept to a minimum to ensure they are economic and use the lowest energy possible Unlike older appliances you will not see high water levels in the drum during washing We recommend always washing as close to a full load as possible see Programmes Table for the maximum load size of your selected programme 16 Detergents and Laundry Detergent dispenser Do not put any items into the drawer other than detergents designed to be released from the drawer as they may cause damage or blockage Drawer release catch Pre wash deter gent compartment Maximum 200ml powder or 100ml liquid Main wash detergent compartment Maximum 400ml powder or 200ml liquid Fabric conditioner compartment Maximum 120ml Dispensing powder detergent To achieve the best wash results the manufacturer s recommended amount of detergent should be measured and added to the main detergent compartment Dispensing tablets Tablets can be dispensed via the machine drum or via the dispenser drawer Please CHECK the detergent pack for dispensing instructions Incorrect use can damage your laundry Dispensing liquid detergent We recommend the use of a detergent dosing ball as provided by your detergent manufacturer Adding fabric conditioner Pour the recommended amount of fabric conditioner into the compartment Do not exceed the maximum fill line Pre Wash When selecting prewash add detergent to both the pre wash a
25. fore you start using your machine p uiejdx4 Sj qeq1 useN Control Panel Features 9 Aquarius Aquarius n v D Programmes and Option Modifiers 10 16 Starting a wash and dry programme z i O Drying ie Programme table D Option modifiers and special features to 5 D 5 D Detergents and Laundry 17 Detergent dispenser Care and Maintenance 18 Cleaning your machine Fuses Changing the plug SISIJIPOW uoin do pue s uiuueuBo id ao ag Precautions and Advice 19 20 T General safety a 3 Saving energy and respecting the environment lt a Disposal lt v O 5 0 Something Wrong Troubleshooting 21 23 oo 53a Service 24 Before calling for assistance v D Spare parts ao Key Contacts gt E Keep this instruction book on hand in order to refer to it when necessary Take it with you when you move and should you sell this appliance or pass it on to another party make sure that this booklet is supplied along with the appliance so that the new owner may be informed about warnings and suggestions on how the machine works Buryooysajqnouy BuoumM Buiuag uijos Hotpoint 3IAJ8S Wash Labels Explained C CCE O t NZ O The number inside the wash tub shows the maximum water temperature in C If there are no bars the garment can be spun and rinsed as normal One bar indicates a reduced spin speed programme should be used
26. g plug you will be charged for a service engineers visit if a problem with your machine is caused by incorrect installation or misuse Control Panel Features Hotpoint Aquarius control panel Programme listing Option buttons Indicator Start Cancel On Off and lights lights button Pe s k pies M ae ae Wash aii Zz Dry A eo Colourtast Cotton i r FEAWSh CD Reduce Creases 80 i No Heat 480 oga m ra Ron Nin Cotton w oda Bouin C Rinse Hold J Pump Out 70 30 160 60 C Time Saver D AQUARIUS lt lt _ p Detergent dispenser Variable Temperature drawer dial Programme selector Drying Times dial dial Aquariust control panel Programme listing Option buttons Indicator Start Cancel On Off and lights lights button button Digital display Start On of Cance TC Drying High Heat C C Reduce Creases E 169 Fast Wash F WJ Colourfast Cotton C Rinse Hold C Time Saver C Time Delay AQUARIU st Super Silent UT Variable Temperature button Detergent dispenser drawer Programme selector Drying Times dial button Control panel features e Programme listing To consult a straight forward chart of the different programmes available Option buttons To select the options available see Programme Table and Option Modifiers e Option lights When an option is
27. g removed you will be charged for a service engineers visit if a problem with your machine is caused by incorrect installation or misuse Installation Levelling Your machine will be noisy if Lhe two front feet are not adjusted so that the machine stands firm and level The machine must be levelled from side to side and from front to back 1 Move your machine into its final location taking care not to trap or kink the hoses 2 Turn one or both front feet anti clockwise by hand until the feet cannot be turned any more When adjusting the feet use a spirit level to check the machine stands level from side to side and from front to back The spring on each foot will stop them coming loose If it is placed on a fitted or loose carpet adjust the feet in such a way as to allow enough room for ventilation beneath the machine Water Connection Connecting the cold water inlet hoses with the Y piece connector Remember please use the new hoses supplied Fitted to the machine Old hoses may cause leaks due to worn out washers or may be split due to water pressure Remember This is a cold fill machine BOTH fill hoses blue connectors fitted to the rear of the machine MUST be connected to the COLD water supply via the Y piece connector Before making connections to the cold water supply allow the water to run freely from the supply tap until it is perfectly clear COLD WATER SU
28. h this may also damage your laundry and the machine Do not pull on the power supply cable to unplug the appliance from the electricity socket Pull the plug out Do not touch the drain water as it could reach very high temperatures over sink drainage Never force the machine door this could damage the safety lock mechanism design to prevent any accidental opening In the event of a malfunction do not under any circumstances touch internal parts in order to attempt repairs Should it have to be moved proceed with the help of two or three people and handle it with the utmost care Never try to do this alone because the appliance is very heavy Before loading your laundry into the machine make sure the drum is empty Be careful not to touch the drum at the top as this area does get hot during drying Models Dimensions Capacity Electric connections Water connections Spin Speed Control programme according to IEC50229 C Technical Details Chart WD645 WD640 WD440 WD420 59 5cm wide 85cm high 60cm deep From 1 to 6kg Wash From 1 to 5kg Dry Voltage 220 240 50Hz Max absorbed power 1700W 2100W Maximum pressure 1 MPa 10 bar Minimum pressure 0 05 MPa 0 5 bar Drum capacity 54 litres up to 1400 rom WD645 WD640 WD440 up to 1200 rpm WD420 60 C cotton programme D with Wash Enhance Wash run with a 6kg load Dry run with 5kg and 1kg loads This appliance is compliant with t
29. he Following European Community Directives 73 23 EEC 8 93 68 EEC Low Voltage and subsequent amendments 89 336 EEC 92 31 EEC amp 93 68 EEC Electromagnetic Compatibility and subsequent amendments Something Wrong Troubleshooting K Hotpoint If your machine seems not to be working GO through the following troubleshooting suggestions BEFORE you call your Service Centre see Service Section 1 All Aquarius Models General Troubleshooting Possible causes Solution Problem The machine won t start Nothing lights up on the control panel Lights illuminate on the control panel but the wash cycle will not start The machine fails to fill with water The machine does not drain or spin during the first wash cycle after installation The machine does not drain or spin although it has drained spun during previous wash cycles The programme takes a long time Check the appliance is fully plugged into the socket and switched on Is the socket ok Try another appliance in the socket to check Is the fuse in the plug ok If not replace it fuse must be 13 Amps see Care and Maintenance There has been a power failure Check another electrical device in your home to see if this is the case The ON OFF button has not been pressed The Start Cancel button has not been pressed for at least 3 seconds Press and hold the Start Cancel button until the machine starts to operate
30. he correct disposal of their old appliance 19 GB SJSIJIPOW saunjee uolzeyjeqsu p uie dx3 sau 3uo2 uoigdiuos q pue aue sjue6ue398q uolgdg pue j ued joujUO07 sjeqe7 use sawweuboud CPIUTERUIJ NE Aupune pue 3IApV pue suolg ne2 Jd Buryooysajqnouy BuoumM 3IAJ8S Buiyzewos Precautions and advice Safety advice This machine was designed and built in compliance with the applicable international safety regulations The following information is provided for your safety and should be read carefully 20 This machine is designed for domestic use only Before using your machine make sure that the TWO transit bolts TWO rubber grommets and TWO spacers have been removed see page 5 Any electrical work necessary to install this machine should be carried out by a qualified electrician Do not plug your machine into a socket when your hands are wet Do not try to modify this machine in any way Do not let children play with the machine or with its controls Do not lean on the door or use the door to lift or move the machine Do not wash garments that have previously been treated with solvents Do not connect the machine to a single outlet instantaneous water heater Do not connect the machine directly to a water softening unit use the recommended amount of detergent for the water hardness in your area Do not overload or underload the machine In addition to reducing the quality of the was
31. imes dial to select the drying time The dial does not rotate during the cycle turn it to the Off position after the programme has finished e Auto Drying programme Sensor Dry if available Aquarius only When selected the machine will automatically sense when the laundry is dry and switch off Press the Drying Times button Auto will appear in the display Remember with both the Timed Drying programme and the Auto Sensor Dry programme if available the Drying High Heat option needs to be selected if drying non delicate loads eg Cottons Drying table Fabric Programme Dry Weight load Heat setting for smaller loads reduce the drying time accordingly Time Setting approx max 3 hours max 2 hours Itis recommended that you separate your drying loads into similar fabric types as this will increase the drying efficiency 11 sounjes4 uo qejie3suj p uie dx3 s3au 3uoo uo 3dii5s dq D s qe1 use W j ued ou3uoo S4 JIPON uoin do pue s wwWe eJoJd ueu zuieWw Aupune pue 3IApV pue suolg ne2 Jd Buryooysajqnouy 3IAJ8S BuoujA Buiyzewos sjuebuejeq pue aue7 Drying Important information Operating the machine To improve the life expectancy of your machine it is recommended that you do not stop or cancel your programme during the drying cycle IL is recommended that you allow the program
32. items eg quilts bedspreads pillows etc expand when dry preventing air flow through the machine Items containing plastic film foam rubber or rubber like materials eg pillows cushions PVC rainwear or inflammable articles which contain inflammable substances eg towels contaminated with hair lacquer Fibreglass eg some types of curtains Items which have been dry cleaned 13 Programme Table Programmes Something an Wash Labels Control Panel SEW ke iehi Detergents Care and Precautions Wrong g O Description Contents Explained Installation Features We IFI and Laundry Maintenance and Advice Troubleshooting Service Sa8Se MOl ld Bansal jess Jeamuapun 40 sway J AAA E JeamJ pun 40 sway pun 4 H sewed JO 48S seuue q 40 48S A sewed 40 48S C s sno Sas gS s snojg s snojg am ss lg 6 s snojg SWIUS B S1JIUuS O s ss Jq w ne ae sassaug su JpluO Z To eee Q aly IILAHLNAS S aMOL UIE Ss JILAHLNAS sj mol 43eg z NOLLOD m n JlQGes 37U34 4JIp JOJ SPCO ONIAHG Wnwixew JO s jdwex OML JlQes Ju J JJIp JOJ SPCO HSVM Wwinwixew Jo s jdwex OML J JEM JO IIV 20 0 9 p ndw s soueldde y saunsua uluue 6oid eied silu J ino dung jas Od ulds Jeu s leoll q QI Aejaq eu 008 OL 0O p ds aleipeuuelul y s 9 dujuo5 uuuue 6oud eed silu uds Mo S SS oO LO gt ulds jeul uoopo LU Aejaq aul Xp GIG 9 p ds wnwxew y s j jdwoo
33. j9 9 nzes dw J009 V ysemald d V 0 O uiw u c u 19 q suondo ajqeyieay suondo ajqeyieay p ds I A97 uu l ulutg1Boid 6 92 Q pepuswwossy snuenby snuenby ulds IIOS ajewixolddy peo7 xen dw L uo ndi i5s d 9 1qed d l swweibolg jeqeq di Option Modifiers and Special Features Option modifiers Not all options can be used on all programmes see Programme Table for option availability e Drying High Heat Use this option to select a higher drying temperature for more hard wearing or heat resistant cotton material When a drying only cycle is selected the default temperature is low heat press the Drying High Heat option button to select the high heat programme On a wash and dry setting high heat can only be selected if a cotton wash is selected first If a synthetic wash programme is selected with a drying programme the temperature is limited and high heat cannot be selected This is to prevent damage to more delicate fabrics e Reduced Creases Selecting this option will run the wash programme with a more gentle action and lower spin speed in addition to carrying out an additional rinse to ensure your laundry has fewer creases and will require less ironing e Rinse Hold Selecting this option will pause the cycle in the final rinse with the fabric conditioner keeping the laundry fresh until you are ready to complete the programme The Rinse Hold light will f
34. lash to indicate the cycle is paused The machine will stay in this state tumbling the load occasionally until either the Start Cancel button is pressed or the Rinse Hold button is pressed again to continue the cycle e Time Saver Use this option for smaller loads less than the capacity listed for the material and programme type see Programme Table This option reduces washing time saving energy The time saved depends on the original programme duration and wash temperature the longer the original wash programme the more time is saved using this option e Extra Rinse Aquarius only Provides a full extra rinse to ensure the maximum possible detergent removal particularly useful for people with sensitive skin Time Delay Aquarius only Use this option to delay the programme start by up to 24 hours The display will show the delay chosen Each press of the button increases the Time Delay in increments of 1 hour If you press the button again after 24 shows in the display the machine will reset the Time Delay and show OFF in the display pressing the button after this will start the Time Delay selection from 1 hour Once the countdown reaches zero the programme will start e Variable Temperature Use this option to reduce the wash temperature below the maximum for the programme you have chosen Aquarius only if available on your model turn the dial to the reduced temperature required When the programme has finished reset th
35. lql pew uew JO Aenea e ysem o paubisap j y s qy pew ue OS D 4 fab N Aejaq owl suly 21x4 Buljlos woqqnis UO OD ISeLINO OD UoN INOJ OD lJV PIOH sulti yeaH YBIH uq PIOH esuly JeeaH YBIH Buqa Xe JewJoN Gye L 9 Or BJOW JO J9 9 D 0h OAISUAJU JUBIOIYe AB eua ss y plepuels 0p 3 Aejaq etl suly 2x4 Souqes UO OD ISeLNO OD INO OD auy s se 1O sonpey Je H uBiH Huq s se O sonpey H uBiH Buruq Xp 1464 00 1 G 09 u ul 9 uollo2 JUeIsISal e u p jios l1uBi Jo 5 9 se v USPAA1SpjJ 09 3 O T Aejaq aul seneg sw OSUIY 214XF I APS OU Ayoedeo peo wunwixew 9G709 031 uolloo senojop x INO OD luV PIOH suly ea YOIH Huq PIOH esuly Tee YOIH Huq Xp EWION 00 9 09 y Buisn o o uay A61 u Bulue o AI1Su 1ul uv piepub S 09 a o D Ae aq Oui PlOH SUlY suly 8x4 POH SUlY soluqe Buup A uoloo ISeLNO OD INO OD Jany s s 1O 9np ti FPH uBiH Buruq sasea sonpay PH uBiH Bua Xen AxeoH 02 2 G 09 prey pajos jaeay JO uuuuej56oid Bulue o nsuazul uv ysemiadns 09 9 fab s 9 qeL Aejaq w AACS OWI OSUIY CXF AACS UII UO HOD SUM J8PMOd Og ALY PIOH sulti JeaH YBIH Huq PIOH sulti Jee YBIH Bulg Xe ELON oez 9 G6 u ul pue uoloo JUeISISA yeay Bulue A pJey 10 4 a1ualbAH S6 g uuuue1Boid ysem urew e p XIN pinbi oig any Aejaq ull e H oz 0 9 og Buno s asojaq sule s u sooj 0
36. m But if the load is wet and the machine completes the wash cycle then the amount of water into the machine is sufficient Has the drain hose been installed correctly see Installation Are the drain hose standpipe or undersink connections blocked Note If the drain hose is connected to an undersink U trap Check that the sink trap blanking plug was removed before the drain hose was connected This is the most common installation fault Is the drain hose kinked or squashed Check the hose at the back of the machine Carry out the additional checks listed below There has been an unbalanced load in the drum and the machine could not spin Try the machine again with a different wash load see Automatic Features Programmes and Option modifiers Has the Rinse Hold option been selected Rinse Hold indicator light will flash To complete the paused programme press either the Start Cancel button or the Rinse Hold button see Programmes and Option modifiers IF the machine completes the wash cycle it is unlikely there is a problem Check the programme table to be sure the programme you have selected is that most suited for your needs The table also gives an indication of approximate programme times you can expect Note The programme times listed in the Programme Table are approximate Options selected can affect the programme times see Programmes and Option Modifiers The wash load temperature and pres
37. m the dispenser drawer water leaking down the front of the machine Check that the detergent dispenser is not blocked or obstructed Remove the drawer from the machine and clean it see Care and Maintenance Check the cold water supply tap is turned on sufficiently see Installation Is your water pressure is within limits see Technical Details Chart if it is too low it may not be sufficient to flush all the detergent out of the drawer Check that the detergent dispenser is not blocked or obstructed Remove the drawer from the machine and clean it see Care and Maintenance Is your water pressure too low see Technical Details Chart Note Are you using detergent tablets If yes please check the detergent manufacturers instructions on the side of the detergent box not all detergent tablets are suitable for use in the dispenser drawer some need to be placed into the machine drum with the wash load for them to dissolve correctly Check that the detergent dispenser is not blocked or obstructed Remove the drawer from the machine and clean it see Care and Maintenance Something Wrong Troubleshooting K Hotpoint Section 2 All Aquarius Models Problems with the Drying cycle The laundry is not dry after using the dry programme The load is warm at the end of the drying cycle The machine spins during the drying cycle The Drying Times dial does not count down Aquarius only Your machine uses cold water
38. me to complete its full cycle which includes completing the cool tumble A 20 minute cool tumble is included at the end of drying allowing fabrics to cool down minimising creasing The load may still be warm when removed from the machine IF your machine is not permanently plumbed in turn on the cold water supply and hook the drain hose over the sink to enable the condensing action to work The dryer is intended for use only where water is used for the cleaning process Be careful not to touch the drum at the top as this area does get hot during drying On no account should liquid fabric conditioner be added during the drying process Misuse of the dryer may create a fire hazard Select HIGH heat by pressing the Drying High Heat option button O will show in Display Aquarius only If this option is not selected the programme will automatically default to low heat CU will show in Display Aquarius only A spin cycle may be carried out during the drying programme Your machine is fitted with a revolutionary self clean filter which will flush with water during drying therefore you may hear water entering the machine during the drying cycle The Drying Times dial Aquarius only DOES NOT rotate Return the dial to the Off position at the end of each drying cycle Drycare tips Items not suitable for tumble drying Le Garments with the ITCL code K DO NOT TUMBLE DRY Woollens Large bulky
39. nd the main wash compartments Hotpoint Washcare Tips e DO NOT overload or underload the machine see the Programme Table for maximum load in addition to reducing the quality of the wash this may also damage your laundry and the machine whilst causing the machine to become unstable and noisy We strongly recommend that you DO NOT wash underwired bras in this machine Should the wires become detached it could cause damage to your laundry and the machine If the washcare label states that the bra is machine washable then we advise placing it in a sealed pillow case or a similar washbag Remember you will be charged for a service engineers visit resulting from a detached bra wire e Do not use the machine if the item to be washed does not have a wash label Before washing laundry we recommend you e Pre treat awkward stains with washable treatments Do not wash any items that have previously been treated with solvents e Close zips fasten belts tie strings and close press studs to prevent tangling Empty all objects from pockets as they may damage the laundry and the machine Remember you will be charged for a service engineers visit to rectify malfunction resulting from objects such as coins pens hair grips etc falling from pockets e Limit the size of absorbent loads ie towels to half loads to give good washing and rinsing results Place small items in a wash bag e Always follow the care l
40. nment In addition avoid using fabric softener as much as possible e If you use your machine between late in the afternoon and the early hours of the morning you will help reduce the electricity board s peak load 2 Recycling and Disposal information As part of Hotpoint s continued commitment to helping the environment Hotpoint reserve the right to use quality recycled components to keep down customer costs and minimise material wastage e Please dispose of packaging and old appliances carefully e To minimise risk of injury to children remove the door and plug then cut off mains cable flush with the appliance Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains socket and the door cannot be locked shut Disposal of old electrical appliances The European Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment The crossed out wheeled bin symbol on the product reminds you of your obligation that when you dispose of the appliance it must EE be separately collected Consumers should contact their local authority or retailer for information concerning t
41. plug your machine when cleaning it and before all maintenance operations Do not clean any part of the machine with abrasive cleaners scouring agents acids any bleach or metal polish as they may cause damage e Use a damp cloth or silicon polish to clean the exterior surfaces of the appliance e Clean the internal surface of the door bowl regularly with a soft cloth A build up of soap powder and water hardness residue may result in water leaking from the door e Always leave the appliance door ajar to prevent unpleasant odours from forming Cleaning the dispenser drawer and compartments It is advisable to clean the dispenser drawer regularly Do not try to clean any part of the dispenser drawer while the machine is running 1 Pull out the drawer until it reaches its stop 2 Press the drawer release button to remove the dispenser drawer see pic 3 Clean and dry the dispenser drawer syphons grate and Fabric conditioner exit channel A ensuring any build up of detergent and fabric conditioner is fully removed Failure to do so may lead to the machine leaking from the dispenser drawer Also regularly clean the outlet pipe area B 4 Relocate the dispenser drawer and push it firmly back into place We recommend a maintenance wash 2 or 3 times a year to avoid a build up of greasy deposits and water hardness residue Run the 95 White Cotton programme with the normal amount of detergent but no l
42. rammes a wash cycle can be immediately followed by a drying cycle To select this simply select the desired wash programme and then select a drying time Aquarius and Aquarius or an auto dryness level Aquariust only and the appropriate temperature for the drying cycle default is LOW heat press the Drying High Heat option button for cottons Press the Start Cancel button and the wash cycle will start and when complete the drying cycle will automatically commence Note The maximum capacity for a Wash amp Dry load is Cottons 5kg 3kg Synthetics e Handwash A gentle action programme for delicate items and items labelled as hand wash only Not for Wool or Silk garments use the special programmes for those materials HAND WASH WOOL APPROVED e Handwash Wool Approved The wool wash cycle on Hotpoint machines has been tested and approved by the Woolmark Company for washing garments labelled as hand wash provided that the garments are washed in accordance to the instructions issued by the manufacturer of this machine This cycle is selected by turning the Programme Selector dial to the wool programme and selecting the Wash Enhance option modifier see Programme Table and Option Modifiers We recommend using a wool wash liquid when using Wool programmes e Super Silent Wash Using the latest brush less electric motors and damper technology the noise levels during the washing phase are signifi
43. selected the corresponding light is illuminated Variable Temperature To reduce the selected programmes wash temperature see Programme Table and Option Modifiers dial Aquarius only Turn to required temperature When the programme has finished return the dial to its original setting button Aquarius only Each press of the button will reduce the wash temperature by 5 C e Drying Times To set the drying time dial Aquarius only Turn to required time When the programme has finished return the dial to its original setting button Aquarius only Press to select drying times from 1 to 3 hours see Setting Drying Programmes e Programme selector dial To select the programme you require The knob stays still during the cycle e Start Cancel button To start the programme or to cancel it if incorrect settings were selected e On Off button To turn the washing machine on and off Indicator lights Shows if the door is locked when lit the door cannot be opened and the stage of the programme that the machine has reached wash rinse or spin saunjese uo ze e3SU p uie dx3 s3au 3uoo uo 3dii5s q sjaqe yseM j ued ou3uoo SJ IJIpON uoin do pue sawweuboud s u u 4 q ueu 7zuiew Aupune 7 pue pue sep 3IApV pue suolg ne2 Jd Buryooysajqnouy BuoumM Buiyzewos 3IAJ8S Starting a Programme Starting a typical wash and dry programme 1 Switch the m
44. sure of the incoming water supply can cause some variation in the programme times C1 GB SJ JIPpOINN s un3e g uolzeyjeqsu p uie dx3 sau 3uo2 uoigdiuos q pue aue sau Bu 3 q uodo pue j ued joujU07 sjeqe7 use s uliuleuBo d S5ueu quIlIBlN Aupune pue 3IApV pue suoi lne5 d Buryooysajqnouy BuoumM BdIAIIS Buiy Zewos Something Wrong Troubleshooting There is too much foam in the drum during the wash cycle Steam is coming from the dispenser drawer The machine makes a noise or vibrates too much during the spin cycle The machine leaks Not all the detergent has been flushed out of the dispenser drawer The dispenser drawer will not close properly or is collecting water pe Check that the detergent you have used is suitable for Automatic machines Refer to the detergent manufacturers recommendations to ensure that you have not used too much detergent IF you have used the wrong type of detergent or too much select a Rinse programme to flush out your machine This is not a fault we have designed the machine to release steam from the drawers during hot washes It may also vent during drying The o fixings were not removed correctly see Installation Remove the transit fixings Failure to remove all the parts of the transit fixings will cause the machine to vibrate excessively during spin Note There are TWO transit fixings that need to be removed
45. tails table see page 20 If the water inlet hoses are not long enough you can purchase an extended hose from Hotpoint Service on 08709 077 077 Always use a new inlet hose Check the water inlet hose at least once a year replace if cracked as worn hoses could split under water pressure Turn on the water supply and check that the connections do not leak If there is a leak turn off the water supply disconnect the hoses and check that the sealing washers are in place Refit the hoses and turn on the water supply the most common cause of problems with water connection is that the customer has not turned the supply tap on itis very important to ensure that your hoses or cables are not kinked or squashed when the machine is pushed back into its location as this can lead to your machine failing to fill or empty the water the majority of problems with noisy machines are due to the feet not being adjusted correctly to level the machine G ua uoigdiuos q sau qauo2 uolzeyjeqsu p uiejdx4 Sj qeq YSeM s un3ae g jaued jou uU07 SISIJIPOW uoin do pue sawweuboud s u u 4 q ueu 7zuiew Aupune 7 pue pue sep 3IApV pue suolg ne2 Jd Buryooysajqnouy BuouMm Builyzewos 3IAJ8S Installation Drainage Connection Although you may need to move the hooked end support along the grey drainage hose DO NOT remove IL
46. tely during the wash cycles high water pressure could cause a cracked hose to split open Never use hoses that have already been used e Inthe unlikely event of something not working see the Troubleshooting section Saving energy and respecting the environment Environmentally friendly technology IF you only see a little water through your appliance door this is because thanks to the latest Hotpoint technology your machine only needs less than half the amount of water to get the best results an objective reached to respect the environment Saving on detergent water energy and time e To avoid wasting resources the machine should be used with a full load A full load instead of two half loads allows you to save up to 50 on energy Hotpoint e The pre wash cycle is only necessary on extremely soiled garments Avoiding it will save on detergent time water and between 5 and 15 energy e Treating stains with a stain remover or leaving them to soak before washing will cut down the need to wash them at high temperatures A programme at 60 C instead of 90 C or one at 40 C instead of 60 C will save up to 50 on energy e Use the correct quantity of detergent depending on the water hardness how soiled the garments are and the amount of laundry you have to avoid wastage and to protect the environment despite being biodegradable detergents do contain ingredients that alter the natural balance of the enviro
Download Pdf Manuals
Related Search