Genie 1022 Garage Door Opener User Manual
Contents
1. 5 Power Head With Rear Cover Removed FIG 3 3 Insert wires Child can be pinned under autamatic garage deor Geath or serious injury can result Mewar let child wk or run under moving door Hever let child use door sooner controls ae hisp moving door in sight Tt p rton i pinned puth ooetrad i bulion or usg FIG 3 5 Mounting Entrapment warning label PN 3642036212 8 09 2007 1 5 WARNING There should be no electrical power to the operator while installing Safety Beam wires If you have plugged in the power cord UNPLUG IT NOW 1 Mounting brackets e Mark both sides of garage door frame or wall no higher than 6 and no lower than 5 above floor Fig 4 1 e Hold bracket against door frame or wall Check if brackets extend out from wall far enough so tongue of bracket is beyond door tracks or any door hardware If not a Mounting bracket extensions are available through an authorized Genie dealer S b Blocks of wood etc may be substituted for FIG 4 2 extensions Mounting brackets e Center bracket on your mark Fig 4 2 e Fasten each with 2 screws Fig 4 2 FIG 4 3 Attach sensors to brackets 2 Mounting Safety Beam Source Red LED and Sensor Green LED e If garage has only one garage door Determine which side of garage receives most direct sunlight Fig 4 4 Red LED should always be on sunn2. Contact The Genie Company at 1 800 35 GENIE e Contact factory authorized dealer for service e Wait until Thermal Protector cools and resets NOTE The 5 BLINKS pattern will remain blinking until the next operator activation If the Thermal Protector does not reset Contact factory authorized dealer for service TRANSMITTER COMPLIANCE STATEMENT Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture No warranty is made that they comply with all legal requirements of any other jurisdiction If transmitters are to be used in another country the importer must determine compliance with any local laws and regulations which may differ from United States and Canadian requirements prior to use Los transmisores cumplen con todas las reglamentaciones legales de los Estados Unidos y del Canada en la fecha de fabricaci n Ninguna garant a se da que cumplan con todas las reglamentaciones legales de ninguna otra jurisdicci n Si los transmisores se van a utilizar en otro pais el importador debe determinar si cumplen con las reglamentaciones y leyes locales que puedan ser diferentes a las reglamentaciones de los Estados Unidos y del Canada antes de usar los mismos Les metteurs sont conformes a la r glementation am ricaine et canadienne a compter de leur date de fabrication Aucune garantie n est stipul e indiquant qu ils sont conformes a toutes les prescriptions juridiques d autres autorit
3. 3 1 Split and strip ends of wire Fig 3 2 Fasten wire to control board screws on back of ean wall control button FIG 3 2 Splitting and stripping White wire to the plus terminal White striped wire to the minus terminal FIG 3 1 Wall control wire routing PN 3642036212 8 09 2007 3 Securely fasten wires e Securely fasten wires to ceiling and wall using insulated staples provided Use insulated staples Staples should be snug only If rear cover is attached to power head remove it On power head Route wall control wires through wire guide Split and strip ends of wire Fig 3 2 on previous page Insert wire into terminal holes and lightly press in the orange locking clips above each terminal hole You can use a pencil or small screwdriver to comfortably press in locking clips The white wire into 2 terminal hole and striped wire into the 1 terminal hole Confirm wire lock by lightly tugging on the wire The wire should remain in the terminal hole e Do NOT install rear cover yet Insulated Staple 4 Mounting e Fasten wall control to wall with 2 screws provided Fig 3 4 e Remove protective backing from Entrapment warning label Fig 3 5 The Entrapment label is located in the center of this manual Stick label on wall near wall control Locking Clips Terminal 1 l fi SE QO 6 OE
4. 5 2 Remove existing power cord and strain relief from the 7 8 dia hole and discard Fig 5 3 Connect permanent wiring to power head using 7 8 diameter hole White to white black to black ground to green Use only UL recognized wire nuts FIG 5 4 Check Safety Beam Alignment Wires inside the power head must be at least 6 INFRARED PROTECTION FUNCTION in length Replace motor cover and rear cover and When the garage door is opening its movement re energize the circuit will not be influenced if the Safety beam is obstructed If the safety beam is obstructed before the garage door closes the door will not close When the garage door is closing if safety beam is cut off by people or obstacle the garage door will NOTE The Genie Company is not responsible for charges resulting from work preformed by an independent electrician WITH POWER SUPPLIED Check Safety Beam alignment Fig 5 4 reverse automatically to its fully opened position e Insure that no part of door or its hardware is Meanwhile the opener light will keep blinking until in path between lenses of source and sensor door moves to its fully opened position e Insure that tops of lenses are between 5 6 above the floor Fig 5 4 The brackets are flexible and can be adjusted slightly if needed e Adjust the Red LED transmitter by aiming the unit directly at the Green LED receiver Use the
5. If the Safety Beam System fails loses power or is installed improperly you will have to press and hold the wall control close button until the door reaches its fully closed position The LED indicator light on the power head will be green adjustment screw located on the top of the and blink twice Pattern lt 4 pause 277 pause transmitter housing to make adjustments to inform you to eliminate problem first e The Red LED transmitter will blink if there is a misalignment When the LED units are aligned Otherwise the door will reverse automatically to the Red LED will remain ON continuously e After the alignment is finished tighten the adjustment screws on both sensors its fully opened position if you release the close button on the wall control during the closing movement 1 8 PN 3642036212 8 09 2007 1 6 Bele aa FOR HELP 1 800 354 3643 OR WWW GENIECOMPANY COM WARNING Severe injury or death can result if the door closing force is set too high e Never increase the door closing force above the minimum required to move the door e Never adjust force to compensate for a sticking or binding door e Once per month perform CONTACT REVERSE TEST as described on the next page and in Section 10 Limit Controls location on power head LED Open Indicator Light Open Set Limit Up Force Travel Limit Button OPEN Control DEN 1 4 LEARN MANUAL LIMIT FORCE Ole vie D Learn Code CODE C
6. s Si les metteurs sont utilis s dans d autres pays il incombe a l importateur den d terminer leur conformit aux lois et r gles locales pouvant diff rer de celles des Etats Unis et du Canada avant toute utilisation desdits metteurs Sendegerate entsprechen allen gesetzlichen Bestimmungen in den USA und Kanada zum Zeitpunkt der Herstellung Wir ubernehmen keine Gewahrleistung fur die Einhaltung aller gesetzlichen Bestimmungen in anderen Landern Sollen Sendegerate in anderen Landern eingesetzt werden so muss der Importeur vor dem Gebrauch sicherstellen dass die Sendegerate auch solchen lokalen Bestimmungen entsprechen welche von den Bestimmungen der USA und Kanadas abweichen HLF HLA SpREGSS EM MSA NMR REE HEMMER ESSE Hh Aki K AE ARER ZER MR AH STIR HERSH ROBBED AER EGS SEEN MEARS MAMA ENR i ee EE fRICHEML ET LAURA ROD EH EE FICE SMG ld UM tRak Ce Kt KALA YI M A SNOBE FR MOM AICS OEHHA CHO OMX CREATCEMHSRY ti IKEA ge dl Ed OETA Dad ALICE MOA MI SMES S7loHOF ok ETARA ment SLAC JIE CHE S in GE BAC od AFA ok CL Vgl EHAEO JIE CHE AAN ASS SS SAAE ASSIA Su De a FALLS RTE CIS Ha EA eoe E Ayo EL PN 3642036212 8 09 2007 2 28 The Genie Company Professional Access Systems LIMITED WARRANTY What is covered Any defect in material and product workmanship from personal normal household use in accordance with the Owner s Manual For how long Limited 1 year warranty on parts 5 years on motor
7. 3 4 Hex Bolt 5 16 18 x 1 2 Shoulder Bolt 5 16 18 x 1 H MISSING ANY PARTS Please call toll free 1 800 354 3643 SEH DO NOT RETURN TO POINT OF PURCHASE IMPORTANT Information needed when calling e Model number located on packaging e Store city state and date of purchase PN 3642036212 8 09 2007 1 PIECE RAIL HARDWARE ASSEMBLED VIEW FOR HELP 1 800 354 3643 OR WWW GENIECOMPANY COM Power Cord NN Rail with chain Power Head ZC se Chain tensioner Clevis Pin Long Header amp Cotter Pin Bracket 3 PIECE RAIL HARDWARE ASSEMBLED VIEW Power Cord SCH Rail with chain Rail Clamps Power Head Rail Clamp Bolts Hovey anes Release op IN Rail Clamp Nuts Center Rail f Clevis Pin Long Header amp Cotter Pin Bracket PN 3642036212 8 09 2007 IMPORTANT INSTALLATION INSTRUCTIONS WARNING To reduce the risk of severe injury or death 1 READ AND FOLLOW ALL SAFETY INSTALLATION AND OPERATION INSTRUCTIONS lf you have questions or do not understand an instruction call The Genie Company or an authorized Genie Dealer 2 Install only on a properly balanced sectional garage door An improperly balanced door could cause severe injury Have a professionally trained service technician make repairs to cables spring assemblies and other hardware before installing the opener 3 Remove all ropes and remove or make inoperative
8. Who gets the warranty This warranty is limited to the consumer who originally purchased the product Geographic scope This warranty applies only to Genie products purchased and installed in the United States and Canada What we will do If your Genie product is defective we will send replacement parts or at our option repair or replace it at no charge to you If we send replacement parts or repair your Genie product we may use new or reconditioned replacement parts If we choose to replace your Genie product we may replace it with a new or reconditioned one of the same or similar design We suggest that you retain your original packing material in the event we choose to repair or replace your Genie product and request that you ship it to us Be sure to include your name address telephone number proof of date and place of purchase and a description of the operating problem After repairing or replacing your Genie product we will ship it to your home at no cost to you for parts and labor but you will have to pay a minimum of 8 00 for shipping and handling charges Limitations IMPLIED WARRANTIES INCLUDING THOSE OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY AN UNWRITTEN WARRANTY THAT THE PRODUCT IS FIT FOR ORDINARY USE ARE LIMITED TO ONE YEAR FROM THE DATE OF PURCHASE GENIE WILL NOT PAY FOR LOSS OF TIME INCONVENIENCE LOSS OF USE OF YOUR GENIE PRODUCT OR PROPERTY DAMAGE CAUSED BY YOUR GENIE PRODUCT OR ITS FAILURE TO W
9. how you will be mounting the power head feet from the power head once it is mounted Refer It is possible that ceiling joists may not be in the to Section 5 position needed with respect to the garage door operator It may be necessary to add an WARNING additional bracket and fasteners not included DO NOT USE AN EXTENSION CORD with your new door operator kit Refer to DO NOT USE A PORTABLE GENERATOR This Section 2 i product is designed to operate on standard house current Check the wall directly above the garage DO NOT USE ALTERNATE POWER SUPPLIES door The door operator s header bracket must be securely fastened to this wall Insure that the structure will provide a strong mounting To avoid damage to your door and or location Refer to Section 2 operator make sure you disable and or remove any door locks ropes and or cables Check to see if the mounting location prior to installing your operator Refer to for the Safety Beam System is clear from Section 1 obstruction and has a wood surface available for attaching the mounting brackets The brackets may be attached to concrete if necessary but extra tools and special fasteners not supplied will be required Refer to Section 4 and 5 Insure that your door is properly balanced and moving freely Refer to Section 2 NOTE Mounting brackets must be installed within code specifications l If your door jambs binds is improperly Is your sectional g
10. make sure it is working properly No re programming is needed 2 Visor clip You will have to install the visor clip if you choose to carry your remote attached to the car visor e Slide visor clip into back of remote control It will snap into place Fig 8 3 ES Open battery cover LIGHT BULB LENS INSTALLATION NOTE For lens cover locate Box 4 1 Light bulb e Recommendations Do NOT use a short neck bulb Light bulb should be no more than 60 Watts Use a heavy duty service bulb for longer life e Screw bulb into socket 2 Lens e Select the white lamp cover Do NOT use the colored cover in this location e Line up lamp lens tabs on power head with corresponding slots in lens Fig 9 1 e Slide lens onto power head Make sure the tabs are fully engaged into lens slots Fig 9 2 e Plug power cord back into electrical outlet FIG 9 2 Fasten lens PN 3642036212 8 09 2007 IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of severe injury or death 1 READ AND FOLLOW ALL INSTRUCTIONS Never let children operate or play with the door controls Keep the remote control away from children Always keep the moving door in sight and away from people and objects until the door is completely closed NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR NEVER GO UNDER A STOPPED PARTIALLY OPEN DOOR Test operator monthly The door MUST reverse on contact with a 1 1 2 high object or a
11. 0 O Wall Control Button amp Three button Remote Control 0000000 End Rail Section Door Arm PN 3642036212 8 09 2007 FASTENERS Shown Full size See Parts List below for full description BAG NO DESCRIPTION RAIL SECTION CLAMP RAIL CLAMP BOLT 5 16 18 x 5 8 HEX FLANGE NUT 5 16 18 BOLT 5 16 18 x 1 2 Rail Clamp Bolt 5 16 18 x 5 8 2 CLEVIS PIN LONG 5 16 x 3 COTTER PIN HEADER BRACKET EE WM LAG SCREW 5 16 x 2 3 HEX BOLT 5 16 18 x 3 4 HEX FLANGE NUT 5 16 18 LAG SCREW 5 16 x 2 10 16 x 1 1 4 Phillips Hex Screw 4 SELF DRILLING SCREW 1 4 20 x 3 4 DOOR BRACKET 5 HEX BOLT 5 16 18 x 3 4 SELF LOCKING NUT 5 16 18 HEEE 4 24 x 1 Pan Head Phillips Screw HEX FLANGE NUT 5 16 18 CLEVIS PIN 5 16 x 3 4 COTTER PIN WALL CONTROL BUTTON ASSEMBLY PAN HEAD PHILLIPS SCREW 4 24 x 1 MN y 13 MM INSULATED STAPLE SAFETY BEAM SOURCE SENSOR BRACKET PHILLIPS HEX SCREW 10 16 x 1 1 4 WIRE NUT GREY REMOTE WITH BATTERY SAFETY BEAM SOURCE SENSOR amp WIRE SET LIGHT COVER WHITE LIGHT COVER COLOR tt Lag screw 5 16 x 2 E S P AIN Q N ND oe sch GA OI on on Nh ra Ne lt Wire Nut IS Clevis pin long UI X 3 5 16 Clevis pin 5 16 x 3 4 Self drilling Screw Cotter pin 1 4 20 x 3 4 Hex Flange Nut 5 16 18 Hex Bolt 5 16 18 x
12. 2 x 4 board laid flat at the center of the doorway on the floor After adjusting either the force or the limit of travel retest the door Opener Failure to adjust the Opener properly may cause severe injury or death When possible use the emergency release only when the door is closed Use caution when using this release with the door open Weak or broken springs are capable of increasing the rate of door closure and increasing the risk of severe injury or death KEEP DOORS PROPERLY BALANCED See your garage door Owner s Manual An improperly balanced door increases the risk of severe injury or death Have a trained professional service technician make repairs to cables spring assemblies and other hardware SAVE THESE INSTRUCTIONS lf you have any questions please do not hesitate to contact customer service at 1 800 354 3643 WARNING Garage door hardware springs cables brackets pulleys etc are under extreme pressure and tension e DO NOT attempt to repair or adjust door springs or any hardware and DO NOT OPERATE garage door automatically or manually if door is improperly balanced or springs are broken CONTACT A TRAINED PROFESSIONAL SERVICE TECHNICIAN ROUTINE MONTHLY MAINTENANCE 1 Door balance e With the door closed pull emergency release knob Carriage Lock towards the opener to release door from carriage assembly e Raise door manually approximately 3 A and release Door should rem
13. ANY COM e Programming incomplete e Complete programming 1 BLINK Pause e Transmitter has not learned e Push button to program Repeat 1 BLINK Pause Repeat e Programming incomplete e Safety Beam sensor obstruction going down e Door obstruction going down e Door obstruction going up 2 BLINKS Pause Repeat e Programming incomplete e Wire to power head or wire connection at power head is bad e Sensors out of alignment e Continuous obstruction 3 BLINKS Pause Repeat 4 BLINKS Pause Repeat e Push button wire short e Push button wires reversed in power head connector 5 BLINKS Pause Repeat e Chain is too tight e Control system failure e Thermal Protector activated 26 PN 3642036212 8 09 2007 e Limits set backwards e Set DOWN LIMIT programming e Check for obstruction remove e Check for obstruction remove Check door spring Contact The Genie Company at 1 800 35 GENIE e Set UP LIMIT programming e Check power head wiring check connections Replace or repair e Check Source amp Sensor alignment e Check for obstruction e Clear limits and reprogram See section DI e Check push button and wiring Staples can cut insulation and shorts wires Repair or replace push button and or wiring Contact The Genie Company at 1 800 35 GENIE e Reverse wire placement in power head connector See section EJ e Adjust chain tension See section Hl
14. BRACKETS CAUTION Header bracket must be fastened to garage framing Do NOT fasten to drywall particle board plaster or other such materials i o d final II Ei height mark WA Hd TEA c door at highest point 1 Finding header bracket mounting location e Close garage door Use a pencil and level a Mark center of garage door one half overall width on the wall with 6 vertical line at top cag ot aor edge of door SE losed b Continue this line on wall above door for pees about 12 Fig 2 1 a position Raise garage door until top edge of door reaches its maximum height Fig 2 2 With door at highest point FIG 2 4 Final height mark Measure height from top edge of door to floor Fig 2 2 Close door again Mark height measurement on wall above door Fig 2 1 c Make your mark across vertical line made earlier Add 2 1 2 to height mark just made on wall This is location for header bracket Fig 2 1 d a 6 vertical line HIGHEST POINT OF TRAVEL WARNING Door springs are under high tension If spring or its shaft is in the way measure 2 1 2 above SECTIONAL DOOR N TRACK spring or shaft on the garage door centerline and mark this height as your location for header bracket Do NOT move door spring FROM HERE SECTIONAL FROM HERE TO FLOOR DOOR TO FLOOR NOTE If header bracket location needs to be above header fo
15. COH L CH M O P 7 i www homelink com Garage Door Opener Model 1022 1024 Includes INTELLICODE Remote Control Up to 7 Single Button Programmable Controls Available Safety Beam System must be installed to close door For use only with sectional doors Your Residential Operator comes with a Rail Assembly which is standard for up to a 7 foot high door Homelink and Car2U compatible For Answers and Assistance 1 800 354 3643 or visit www geniecompany com SAVE THIS MANUAL FOR FUTURE REFERENCE Homelink is a registered trademark of Johnson Controls Technology Company Car2U is a trademark of Lear Corporation PN 3642036212 8 09 2007 OVERVIEW OF POTENTIAL HAZARDS Garage doors are large heavy objects that move with the help of springs under high tension and electric motors Since moving objects springs under tension and electric motors can cause injuries your safety and the safety of others depend on the owner or user of this system to read understand and implement the information in this manual If you have questions or do not understand the information presented contact The Genie Company or an authorized Genie Dealer In this section and those that follow the words DANGER WARNING and CAUTION are used to emphasize important safety information The word A DANGER indicates an imminently hazardous situation which if not avoided will result in death or ser
16. IO RED ROUGE ROJO dn BLANC d BLANCO YELLOW JAUNE AMARILLO YELLOW JAUNE NOIR AMARILLO oo NEGRO WARNING Sr ELECTRICAL SHOCK MOTOR HALL SENSOR MINN MOTEUR CAPTEUR DE PASSAGE emm WHITE RED MOTOR SENSOR DE PASILLO ROUGE ROJO WHITE BLANC BLANCO ORANGE ar ORANGE ANARANJADO STRIPED WHITE BLANC RAYE BLANCO RAYADO STRIPED WHITE BLANC RAYE BLANCO RAYADO PHOTO SENSOR WALL BUTTON PHOTODETECTEUR BOUTON MURAL FOTOSENSOR BOTON DE LA PARED PN 3642036212 8 09 2007 GUIDE OPERATION FOR HELP 1 800 354 3643 OR WWW GENIECOMPANY COM PROBLEM WHAT TO DO Operator does NOT run Check power source from wall control Plug a lamp into outlet used for power head If lamp works power source is OK If not check fuse or circuit breaker e H power is OK Check connections at power head terminals Check connections at wall control e Check for broken or cut wires Staples can cut insulation and short wires Repair or replace Door operator starts e Was a remote control lost or stolen Erase all remote control codes from receiver for no reason memory and reprogram See section K e Button stuck on wall control or remote e Check CLOSE limit switch setting See section Ri e Wires shorted Staples can cut insulation and short wires Repair or replace Door starts down then Check CONTACT REVERSE See section BI STOPS before it s e Check g
17. LOSE SETTING amp TESTING OPEN CLOSE LIMITS The OPEN UP and CLOSE DOWN door positions are controlled by making the adjustments on the panel located on the bottom of the power head The adjustments that can be made are Close Travel Limit Open Travel Limit Maximum Closing Force Maximum Opening Force and Transmitter Programming To Garage Door ENGAGE CHAIN TO CARRIAGE Button a SECH Ce 1 Press and hold the Close Travel Limit le button Button Adjustment until the chain advances and engages carriage Fig 6 2 FIG 6 1 Limit controls CLOSE TRAVEL LIMIT 1 Press and hold the Close Travel Limit le button until the door is fully closed 2 You can quickly press and release the Close Travel Limit le button to move the door in small increments You can also use the Open Travel Limit 2 button to move the door slightly in the UP direction 3 Door is fully closed when the bottom edge of door presses firmly onto the ground ST ATA 7 Chain Master Link engages to carriage 4 Once the door is in the desired position press and release the Down SET Limit amp button The FIG 6 2 Engage Chain to Carriage LED indicator light light will blink green once This stores the closed position in memory OPEN TRAVEL LIMIT 1 Press and hold the Open Travel Limit el button to move the door to its fully opened position This starts the opener moving in the UP direction 2 Hold t
18. NY COM Le C gt KN C gt DEC 3 16 Drill Bit Pencil Carpenter s level Wire strippers Adjustable wrench Ratchet Tape measure 0000 a 1 4 7 16 3 8 and illi i Hammer Safety Glasses 1 2 Sockets Phillips screwdrivers PARTS IDENTIFICATION Not Shown Full Size RRANGING BOX CONTENTS FOR ASSEMBLY TON DU CONTENU DE LA BOITE POUR LE MONTAGE D ORGANISATI IMPORTANT INFORMATION DISPOSICION DEL CONTENIDO DE LA BOLSA PARA EL MONTAJE Child can be pinned under automatic garage door Death or serious injury can result e Never let child walk or run under moving door sce g DEE Ze Eerst ik e Never let child use door opener controls Sas rb E zz priar ei meka a P mate fr mge go Erem ben Mengen pee a a agaia bz vm re Always keep moving door in sight gg Fer ergi rege a kafe pr che e f person is pinned push control button or use emergency release e Test door opener monthly Refer to your owner s manual ce 1 2 inch object or 2x4 laid flat on floor il ontact adju Ol Lamin j fe peia eil jara en paid Header Bracket Insulated Staple Safety Beam Source Door with wire Safety Beam Sensor Bracket Red LED with wire Green LED O OO O Rail Section Clamp Head Rail Section Safety Beam Source Sensor Bracket Center Rail Section O000000000000
19. ORK ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES RESULTING FROM MISUSE OR MODIFICATION OF YOUR GENIE PRODUCT Some states and provinces do not allow limitations on how long an implied warranty lasts or the exclusion of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty is the only one we will give on your Genie product and it sets forth all our responsibilities regarding your Genie product There are no other express warranties State and province rights This warranty gives you specific legal rights and you may also have other rights which vary from state to state and province to province How to get warranty service To obtain warranty service for your Genie product you must provide proof of the date and place of purchase of the product 1 Do It Yourself Service Call the Genie Consumer Connection toll free at 1 800 354 3643 to speak in person to a trained Genie representative for assistance in diagnosing the problem and arranging to supply you with the required parts for do it yourself repairs Trained service representatives are available Monday Friday 8 00 a m 11 00 p m Eastern Time and on Saturday 11 00 p m to 8 00 p m Eastern Time subject to holidays You may also get the information you need at www geniecompany com 2 Service From Authorized Dealers You also may obtain warranty service from Genie authorized dealers We recommend that y
20. ain stationary or move very slightly If door moves quickly HAVE DOOR SERVICED BY A PROFESSIONAL e Close the door e Pull emergency release knob towards door to engage carriage Operate door using remote Door will re attach itself to carriage assembly Op ww 2 Contact reverse e Place a 2 x 4 board laid flat on floor In center of garage door opening e Close door by using wall button or remote control Door fails to reverse on contact with board See section K CONTACT REVERSE Operator still fails CONTACT THE GENIE COMPANY OR AN AUTHORIZED GENIE DEALER 3 Safety Beam System e Red LED blinks check alignment See section Ri CAUTION Use wall control supplied with operator Any other wall control can cause the operator to operate unexpectedly PN 3642036212 8 09 2007 23 24 CIRCUIT WIRING DIAGRAM FOR HELP 1 800 354 3643 OR WWW GENIECOMPANY COM Operator circuit wiring diagram This wiring diagram is for reference only WARNING Opening Cover May Cause ZS Shock Remove power from operator prior to removing cover POWER CORD CORDON DE SECTEUR CABLE ELECTRICO TERMINAL BLOCK SURGE PROTECTOR MOV BORNE LIMITEUR DE SURTENSION BLOQUE DE TERMINALES PROTECTOR DE SOBRETENSIONES E TRANSFORMER BLANCO TRANSFORMATEUR TRANSFORMADOR TC Ns Ku BLACK L ke PRIMARY SECONDARY BLA PRIMAIRE SECONDAIRE NEGRO PRIMARIO SECUNDAR
21. all locks connected to the garage door before installing opener 4 Where possible install the door opener 7 feet or more above the floor For products having an emergency release mount the emergency release 6 feet above the floor 1 OPERATOR ASSEMBLY RAIL ASSEMBLY Use a clean flat surface WARNING To reduce the risk of injury to persons or damage to property Use this operator only with sectional doors CAUTION Do NOT run until operator is fully assembled NOTE Three 3 piece rail assemblies are for a 7 foot high door Clear a workspace area to unpack and organize box and contents for assembly 1 There are 4 boxes inside the carton Each box is numbered 1 4 Note that some operators will contain the same parts and be packaged with fewer boxes Carefully remove the three internal boxes Labeled 1 2 and 3 and place them on the floor for easy access Fig 1 1 These boxes contain assembly parts and the contents are organized by assembly tasks For quick reference inside the lid of each box there is a label illustrating the components inside 2 Remove the motor power head and place it on the floor for later use Remove box 4 and place it on the floor for later use NOTE For 1 piece rail skip to POWER HEAD amp RAIL ASSEMBLY on the next page Do NOT connect the operator to source of power until instructed to do so Locate the control button e Within sight of door e At
22. all rear cover 17 ley CONNECTING TO POWER FOR HELP 1 800 354 3643 OR WWW GENIECOMPANY COM WARNING e To reduce the risk of electrical shock this equipment has a grounded type plug that includes a third grounding pin This plug will only fit a grounded type outlet If you do not have a grounded outlet contact a qualified licensed electrician to install one DO NOT alter the plug in any way The door operator must be properly grounded in order to prevent personal injury and damage to the components e DO NOT remove motor cover All work performed on motor must be done by a trained professional service technician CAUTION FIG 5 2 Remove motor cover e Check local building codes to make sure that you FIG 5 3 Power cord strain relief are not required to have your garage door operator permanently wired with circuit breaker protection If building codes require door operator to be permanently wired have a qualified licensed Do NOT use an extension cord electrician connect power with permanent wiring Do NOT use a portable generator This product WITH GROUNDED PLUG is designed to operate using standard Plug the operator into a properly grounded EE b electrical outlet Fig 5 1 Do NOT use alternate power supplies CAUTION WITH PERMANENT WIRING Instructions for Electrician e Remove power from circuit e Remove rear cover and motor cover Remove four motor cover screws Fig
23. anufacturer or distributor for a bracing kit The Genie Company is not responsible for damage caused due to improperly braced door centerline even with or above top roller 1 Finding door bracket mounting location e Door bracket is mounted as high on door as possible along vertical centerline and NO LOWER THAN top set of rollers Fig 2 7 2 Mounting the door bracket e Proper bracing should be verified at this point Align door bracket centered on your vertical centerline Fig 2 8 Attach using 3 self drilling screws for sheet metal or other light weight material Use lag screws not provided for solid wooden sectional doors FIG 2 8 Examples of door bracket positioning 1 Attach the arms e Fasten curved door arm to door bracket using short clevis pin amp cotter pin bolt and locking nut Fig 2 9 e Fasten straight arm to carriage using clevis pin and cotter pin Fig 2 9 2 Connecting the arms e Slide carriage back and forth to adjust arm length Position the straight arm 50 down from the rail e With the arms arranged in this position fasten arms together using bolts and nuts spaced as far apart as possible Fig 2 9 bolts as far apart as possible FIG 2 9 Attaching door arms PN 3642036212 8 09 2007 1 3 FOR HELP 1 800 354 3643 OR WWW GENIECOMPANY COM Wire from ower head O wall control installing wall control wires and wall control CAUTION Sta
24. arage door for binding closed e Wires shorted Staples can cut insulation and short wires Repair or replace Door starts down then If a NEW installation check Door Arm position See section amp STOPS and goes back Check Safety Beam system for beam obstruction or misalignment of lenses up See section KJ e Check if Safety Beam Red LED is flashing e Check CLOSE FORCE adjustment See section Bi e Check garage door for binding Door will only run e Check OPEN FORCE adjustment See section Ri closed e Check door condition and door spring e A WARNING If you suspect a problem with the garage door hardware or springs contact an authorized Genie Dealer or a trained professional service technician or contact The Genie Company at 1 800 35 GENIE Door will only run open e Check CLOSE FORCE adjustment See section Bi Door starts up but e Be sure door operator and springs are in good repair properly lubricated and STOPS before it s balanced See maintenance section completely open e Check OPEN limit setting See section Ri e Check OPEN FORCE adjustment See section Bi e A WARNING If you suspect a problem with the garage door hardware or springs contact an authorized Genie Dealer or a trained professional service technician or contact The Genie Company at 1 800 35 GENIE Operator runs but e Make sure carriage is engaged to carriage slide door does NOT move Place carriage lever in lock position e Ch
25. arage door made of balanced or has a broken spring have it aluminum light weight steel fiberglass repaired or adjusted by a trained professional or glass panels Additional support bracing must be added to these type doors If this is the case please contact the door manufacturer or authorized dealer so that they can furnish you with a bracing kit Refer to Section 2 WARNING NOT SHOWN If your garage does not have a separate entry door you should consider To reduce the risk of injury to persons or an emergency release kit GER 2 for installation on damage to property Use this operator only your garage door with sectional doors service technician Door springs cables pulleys brackets and associated hardware are under extreme tension and can cause serious injury or death PN 3642036212 8 09 2007 TYPICAL SECTIONAL DOOR INSTALLATION FOR HELP 1 800 354 3643 OR WWW GENIECOMPANY COM 6 is Z s 2 1 ki j l S Q Pg 11 12 TYPICAL SUPPORT BRACKET ADDED HEADER BRACKET MOUNTING BOARD POWER CORD APPROX 45 IN TO 120V GROUNDED OUTLET EXTENSION SPRING OR TORSION SPRING NOTE This operator is designed for use with SECTIONAL doors only SAFETY BEAMS WARNING To reduce the risk of injury to persons or damage to property Use this operator only with sectional doors PN 3642036212 8 09 2007 RECOMMENDED TOOLS FOR HELP 1 800 354 3643 OR WWW GENIECOMPA
26. ay malfunctions Watch Dog Monitoring System Automatically stops and reverses a closing door if the Safety Beam System has an operational problem Automatic Lighting System One bulb lighting supplies up to 60 watts of light for safer evening exits and entries Turns ON when door is activated and automatically turns OFF 3 minutes later Manual Emergency Release Manually releases door from door operator Use during a power failure or other emergency to allow manual opening and closing of door PN 3642036212 8 09 2007 PRE INS TALLA TION CHECK LIS T FOR HELP 1 800 354 3643 OR WWW GENIECOMPANY COM Things to consider if you are planning to Do it yourself This operator is designed for use with SECTIONAL doors only In many cases you will be replacing an existing door operator with a new one however if this will be the first operator installed there are some pre installation issues which need to be addressed They are as follows The Genie Company recommends that you read and fully understand all information and instructions contained herein before choosing a Do it yourself installation Any questions should be directed to The Genie Company or an authorized Genie Dealer The issue numbers below refer to the circled numbers in the illustrations on page 5 Check your ceiling where the power You need a 110 120 Volt power supply head of your new unit will be mounted available The outlet should be no more than 3 Plan
27. e or more of the following U S patents 3 898 582 4 041 259 4 048 630 4 064 487 4 103 238 5 222 403 Other Patents applied for CORRESPONDENCE WITH FACTORY MUST INCLUDE DATE MFG NO LOCATED UNDER LENS OF POWER HEAD FILL THIS IN AT TIME OF INSTALLATION FOR YOUR OWN RECORDS SO THAT IT WILL BE AVAILABLE IF YOU EVER NEED TO CALL US Date Purchased Operator Model Remote Control Model Store Purchased Serial Number Store Address Dealer Name Dealer Address City State Zip Visit Our Website at www geniecompany com SAVE THESE INSTRUCTIONS PN 3642036212 8 09 2007
28. eck to make sure chain is not broken or OFF its track e Check FORCE ADJUSTMENT See section Ri Door operator will NOT run more than 30 seconds each way if door does not move Remote control has e Relocate remote control inside car and or point remote control at garage door less than 25 feet e Replace battery See section Bi operating range or no e Reposition door operator antenna operation e Red LED blinks while button is being pushed or LED does not come on battery is low replace battery Operator works from e Program remote control code into receiver memory See section KA wall control but NOT e Replace remote control battery with good one See section EJ from remote control Noisy operation e Be sure all fasteners are tight e Be sure door and operator is in good repair properly lubricated and balanced See monthly maintenance section Safety Beam System e lf an operational problem exists and operator will not run closed The operator malfunction can be forced to close as follows See section Ri Hold the wall control button down until door is completely closed e Check Safety Beam System alignment e Replace Safety Beam System Sensors e Disconnect the Safety Beam System from the operator and call for repair service PN 3642036212 8 09 2007 IDE POWER HEAD LED Power head LED Red LED Green LED showing showing OFF OFF Continuous ON Possible Problem FOR HELP 1 800 354 3643 OR WWW GENIECOMP
29. he Open Travel Limit le button until the door is in the fully opened position that you desire then release this button 3 You can quickly press and release the Open Travel Limit le button to move the door in small increments You can also use the Close Travel Limit 2 button to move the door slightly in the DOWN direction 4 Once the door is in the desired position press and release the Open SET Limit E button The LED indicator light will blink green twice This stores the opened position in memory PN 3642036212 8 09 2007 19 oF RP G A8 DOD LA VANIA The Carriage Lock can be manually engaged or disengaged e To disengage Carriage Lock Pull handle towards opener e To engage Carriage Lock Pull handle towards door DOWN FORCE 1 By turning the Down Force Control clockwise the DOWN force can be increased By turning the Down Force Control counter clockwise the DOWN force can be decreased Set the DOWN force level at the minimum force required to close door without reversing 2 Once the desired level is selected this stores the maximum force level for the DOWN direction in memory 3 By turning the Up Force Control clockwise the UP force can be increased By turning the Up Force Control counter clockwise the UP force can be decreased Set the UP force level at the minimum force required to open door without stopping 4 Once the desired level is selected this
30. he bolts and nuts POWER HEAD amp RAIL ASSEMBLY NOTE Handle carefully Drive chain can slide out of rail NOTE For power head and rail assembly locate Bag 1 from Box 1 1 Attach rail assembly to power head by aligning the sprocket onto the motor shaft Use 3 bolts 5 16 18 x 1 2 Fig 1 4 2 Tighten the chain by turning the adjustment nut clockwise The chain adjustment nut is located opposite the power head at the other end of the rail Fig 1 5 3 Tighten chain until chain is approximately 1 8 inch above the base of the rail at midpoint on the rail Fig 1 5 Do NOT over tighten chain Rail Clamps Release Knob Rail Clamp Nuts Center Rail Use 5 16 18 x 1 2 H Use 1 2 socket DN on adjustment nut Tighten nut to move pulley this direction SN REMINDER You should have removed all ropes and or cables and disabled the door lock already If you have not remove all ropes and or cables and disable garage door lock NOW before continuing with installation Fig 1 6 FIG 1 5 Set assembled power head and rail aside Begin with Section 2 INSTALLATION FIG 1 6 PN 3642036212 8 09 2007 I 4 hma T Rail at center of rail assembly Chain adjustment Remove Remove Disable garage door lock INSTALLATION FOR HELP 1 800 354 3643 OR WWW GENIECOMPANY COM b extend vertical line F HEADER AND DOOR MOUNTING
31. ious injury A WARNING indicates an potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION indicates an potentially hazardous situation which if not avoided may result in injury or property damage The word NOTE is used to indicate important steps to be followed important considerations or location of parts POTENTIAL HAZARD MOVING DOOR ELECTRICAL SHOCK HIGH SPRING TENSION EFFECT WARNING Can Cause Serious Injury or Death WARNING Can Cause Serious Injury or Death WARNING Can Cause Serious Injury or Death PREVENTION Keep people clear of opening while door is moving Do NOT allow children to play with the door operator Do NOT operate a door that jams or one that has a broken spring Turn OFF power before removing operator cover When replacing cover make sure wires are not pinched or near moving parts Operator must be properly grounded Do NOT try to remove repair or adjust springs or anything to which door spring parts are fastened such as wood blocks steel brackets cables or other like items Repairs and adjustments must be made by a trained professional service technician using proper tools and instructions PN 3642036212 8 09 2007 Operator MUST be installed with the included Wall Control Safety Beam Safety Reverse System MUST be installed to close door INTELLICODE Rolling Code Security Sys
32. k PROGRAMMING REMOTE CONTROLS WARNING A moving door can cause serious injury or death 1 Keep people clear of opening while door is moving 2 Do NOT allow children to play with Wireless Keypad 3 During programming the door opener could begin to run so stay away from the moving door and its parts To keep the door from moving close the door and disconnect it from the Opener by pulling the Emergency Release NOTE For remote control locate Box 3 1a Single Button Remote Programming NOTE This operator can learn up to 7 single button remote controls e Locate learn code button and indicator LED on the power head next to force adjustment screws Fig 7 1 Press and release learn code button Indicator LED will blink RED at a rate of twice per second Within 30 seconds push remote control button once Indicator LED will stop blinking and stay on Press remote control button again Red LED will go out Remote is now programmed 1b Multi Button Remote Programming NOTE Each button on a multi button remote is designed for use with 1 door You cannot program 2 buttons to operate the same door nor can you program 1 button to operate 2 doors You can program a maximum of 7 different transmitters or wireless devices NOTE Pushing two buttons simultaneously will erase programmed memory and limits must be reset e For each button Program each button separately using
33. minimum height of 5 feet so small children are not able to reach it and e Away from all moving parts of the door Install the Entrapment WARNING Label next to the control button in a prominent location Install the Emergency Release Marking on or next to the emergency release After installing the opener the door must reverse when it contacts a 1 1 2 inch high object or a 2 x 4 board laid flat on the floor FOR HELP 1 800 354 3643 OR WWW GENIECOMPANY COM Box Label Example FIG 1 1 Internal boxes PN 3642036212 8 09 2007 9 10 NOTE For split rail clamps nuts and bolts locate Bag 0 from Box 1 me feier la J 3 Remove the two rail sections that are not connected to the chain and place them on floor Fig 1 2 A 4 Carefully remove the third rail section with chain and plastic sleeve Place rail section on floor and extend chain straight out Fig 1 2 B Chain and rail should extend approximately 7 feet 5 Remove wire ties and plastic bag from chain Leave chain extended straight out on floor Avoid kinks in the chain by careful handling and keeping chain flat on the floor 6 Align the three rail sections by pulling the chain straight and wrapping it around the chain tensioner pulley Fig 1 3 7 Attach the two rail clamps to the rail section joints with 4 bolts and nuts After both rail clamps have been assembled to the rail sections securely tighten t
34. om Box 1 e On finished ceilings locate ceiling joists or trusses using a stud finder or similar device Attach angle iron not provided to joists or trusses through finish material using provided lag screws Fig 2 6 e On unfinished ceilings or open ceilings straps may attach directly to joists or trusses Depending on the garage construction extra framing material not provided may be required which should be installed using appropriate construction techniques Fig 2 6 NOTE Refer to your local building codes for appropriate construction techniques e Attach mounting straps to ceiling using lag bolts Fig 2 6 e Set height of power head to following Fig 2 6 a Rail must clear door at door s highest point of travel b Be level or power head slightly below level e Securely tighten power head mounting bolts and nuts e Lower door e Check that rail clamp bolts and nuts are tight e DO NOT PLUG UNIT IN YET e E E FROM ABOVE f not to scale ss ee Tee a Gees ge CLEVIS PIN Pe gt Wee 7 ee a COTTER PIN L ege FIG 2 5 Rail mounting to header bracket ANGLE IRON ON FINISHED CEILING DRYWALL Extra framing not needed bolts amp nuts Extra framing NEEDED FIG 2 6 Mounting the power head 1 2 PN 3642036212 8 09 2007 fiberglass and sheet metal must be properly braced before mounting door operator Contact door m
35. ou verify the dealer s status by calling the Genie Consumer Connection at 1 800 654 3643 or by visiting www geniecompany com before scheduling warranty service If warranty service is provided by an authorized dealer Genie will provide all required parts under warranty at no charge to you but the dealers are independent businesses and may charge for their services Genie will not reimburse you or otherwise be responsible for those charges Your choice of either one of the above described service options is your exclusive remedy under this warranty What this warranty does not cover This warranty does not cover batteries which are considered replaceable parts installation commercial use defects resulting from accidents damage while in transit to our service location or damage resulting from alterations misuse or abuse lack of proper maintenance unauthorized repair or modification of the product affixing of any attachment not provided with the product programming of the Remote Control Devices Safety Beam adjustment cleaning staples through wiring pinched or broken wires Carriage disengaged Force Control adjustments door out of balance broken springs or cables power outages use of extension cords missing or damaged parts on discounted clearanced final sale or taped cartons phantom operation fire flood or acts of God or other failure to follow the Owner s Manual FOR ANSWERS CALL 1 800 354 3643 Manufactured under on
36. ples which are too tight can cut or pinch wires Cut or pinched wires can cause the wall control to stop working When using the insulated staples make sure you fasten them only as tightly as needed to hold the wire snugly control WARNING K Use of any other wall control can cause the door to N REPSI operate unexpectedly and the light not to work GE Use only the included wall control Separate entry door EXAMPLE ONLY This is an example of wire routing when NOT pre wired Your wire routing may be different Wall Control location e Wall Control location should be in direct sight of door e It should be at least five feet 5 above floor to prevent small children from operating door e It must be away from any moving parts You should NOT be able to reach the garage door while standing at wall control e Wall Control board screw connections are polarized positive and negative 2a Wiring If pre wired e Locate wall control pre wired wire ends Fig 3 1 They should be located within the guidelines mentioned above e Split and strip ends of wire Fig 3 2 e Fasten wire to wall control board screws on back of wall control White wire to the plus terminal White striped wire to the minus terminal 2b Wiring If NOT pre wired Pick a convenient location for mounting wall control using the guidelines mentioned above Fig 3 1 Run wire from wall control to power head Fig
37. r garage door opening you need to add a mounting surface A 2 x 6 board securely attached board and fasteners not included to wall studs on either side of your mark is sufficient Fig 2 3 NOTE For header bracket and bolts locate Bag 2 from Box 1 NOTE The bolts supplied in Bag 2 are designed to be used on pressure treated lumber 2 Mounting the header bracket Hold header bracket against wall Fig 2 3 FIG 2 3 Header bracket mounting on header A e Position bracket as shown above header Place center on vertical line Bottom edge on final height line e Mark screw hole locations on wall e Drill 3 16 pilot holes at each screw hole mark Fasten header bracket with 2 lag screws provided Fig 2 3 PN 3642036212 8 09 2007 1 1 MOUNTING THE OPERATOR 1 Getting started e Position assembled rail on wall next to header bracket Fig 2 4 Place material on floor under power head to protect from scratching A box stool or similar device may be needed to clear a torsion spring NOTE For header bracket pins locate Bag 2 from Box 1 2 Mounting the assembly e Attach rail to header bracket using clevis pin and cotter pin e Support power head on step ladder to prevent interference with header mounted spring Fig 2 5 NOTE Before final attachment to ceiling insure that assembly is in proper alignment Fig 2 4 NOTE For nuts bolts and lag screws locate Bag 3 fr
38. rticular installation If this equipment does cause harmful interference to radio or television reception which may be determined by turning the equipment OFF and ON the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiver antenna Increase the separation between the operator and receiver Connect the operator into an outlet on a circuit different from that to which the receiver is connected Consult your local dealer Limit controls location on power head LED Open Indicator Light Open _ Set Limit Up Force EZ Travel Limit Button OPEN Control Adjustment AA SET LEARN MANUAL LIMIT FORCE Ol Ish Code CODE Button CLOSE Close Set Limit Button Down Force Control Adjustment Close Travel Limit FIG 7 1 Learn code button and LED PN 3642036212 8 09 2007 D 22 CR REMOTE CONTROL BATTERY REPLACEMENT AND VISOR CLIP INSTALLATION 1 Battery replacement e Use coin ball point pen or similar device Gently push straight in on battery cover lock tab as shown Fig 8 1 e Flip open battery cover Remove old battery e Make sure new battery is facing proper direction Match battery polarity with symbols inside battery cover Fig 8 2 Recommended replacement battery type Alkaline A23 12 volt e Slip new battery into place FIG 8 1 Snap battery cover shut e Operate remote to
39. stores the maximum force level for the UP direction in memory RASE OPEN CLOSE TRAVEL LIMIT 1 Press and hold both of the SET buttons Si together until the green indicator light blinks about 5 seconds 2 All close and open travel limit settings are erased Then follow the steps above to reprogram close and open travel limits CONTACT REVERSE TEST The force adjustments and limit switch settings MUST BE COMPLETED before testing 1 Testing e Open garage door using wall control Place a 2 x 4 board laid flat under center of garage door opening Fig 6 5 e Close door using wall control e When door contacts board it must stop and reverse within 2 seconds to open position 2 Adjustment e If the door does not properly reverse Check to see if door has close limit programmed It should not have reached its close limit before hitting board If the door STOPS but does not reverse decrease CLOSE FORCE control SI setting slightly turn it counter clockwise e Test again Repeat as necessary 20 PN 3642036212 8 09 2007 FIG 6 3 FIG 6 4 FIG 6 5 UNLOCK LOCK TO RECONNECT PULL TOWARD TO RELEASE PULL TOWARD THE OPENER Engage Disengage Carriage Lock Up Force OPEN Control Adjustment ROTATE CLOCKWISE ROTATE COUNTER CLOCKWISE CLOS E Down Force Control Adjustment Force Control Adjustment 2 x 4 under center of door opening
40. tem An electronic rolling code system that enhances the security of the door operator by continuously Se the access code each time the remote control is used The door operator responds to each new code SCH once An access code copied from a working system and tried again will not control the door operator Lighted Wall Button Operates door operator from inside garage Refer to section 3 IN HomeLink COMPATIBLE www homelink com and Car2U compatible Follow the Homelink or Car2U instructions in your car owner s manual Safety Beam Non Contact Reversing System Puts an invisible beam across the door opening The door stops and reverses to the full open position if anything passes through the beam Red or green LED indicator lights on the power head provide a self diagnostic code if an operational problem exits Refer to Section 10 Safe T Reverse Contact Reversing System Automatically stops and reverses a closing door within 2 seconds of contact with an object Refer to Section 6 Safe T Stop Timed Reversed System Automatically opens a closing door if it fails to close completely within 30 seconds Force Guard Control Features adjustable open and close force settings For maximum safety these must be set to the minimum force required to fully open and close the door Refer to Section 6 Relay Monitoring System Automatically stops and reverses a closing door if the closing rel
41. the Single Button Remote Programming steps 2 Operating e Press remote button once Door will move e Press button again Door will stop e Press button again Door will move in opposite direction NOTE The door will stop automatically at the fully open or fully closed position LOST OR STOLEN REMOTE 1 Clear memory e Press and hold learn code button on power head for 10 seconds or until the red blinking indicator LED goes out e Program remaining or new remote controls as done previously Your door operator will no longer recognize any signal received from the missing remote control or any other which has not been reprogrammed IN HomeLink COMPATIBLE www homelink com NOTE To program a Homelink and Car2U device follow the Homelink or Car2U instructions in your car owner s manual FCC and IC CERTIFIED This device complies with FCC Part 15 and RSS 210 of Industry Canada This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a pa
42. ty Beam System to stop working When using the insulated staples make sure you fasten them only as tightly as needed to hold the wire snugly 4 Split and strip ends of sensor wires Fig 4 7 NOTE For rear cover locate Box 4 5 Attach Safety Beam wire to power head wire terminal e Route Safety Beam wires through wire guide Insert wire into terminal holes and lightly press in the orange locking clips above each terminal hole You can use a pencil or small screwdriver to comfortably reach in and lightly press down locking clips Insert white wires to even terminal holes and striped wires into odd terminal holes Fig 4 8 Losing Terminal x Holes Confirm wire lock by lightly tugging on the wire The wire should remain in the terminal hole e Install rear cover The rear cover is the same color as the power head clips and body Fig 4 9 e Do not install the white lamp cover at this time NOTE Safety Beam alignment check must be performed following connection to electrical power see page 18 DO NOT PLUG IN YET 65 43 21 or 65 43 21 Dashed Line striped wire Head Solid Line white wire Ceiling Power FIG 4 5b Pre Wired source and sensor wiring methods Use this wire routing if NOT pre wired Invisible Light Beam Protection Area FIG 4 7 Splitting and stripping FIG 4 8 Insert wires FIG 4 9 PN 3642036212 8 09 2007 Inst
43. y side whenever possible Fig 4 4 e For multiple doors Preventing crossed signals is critical Place source and sensor modules on adjacent doors facing in opposite directions Fig 4 4 THREE DOOR FIG 4 4 Safety Beam source and sensor locations e Slide source sensor onto tongue of bracket until it clicks into place Fig 4 3 3a Wiring If NOT pre wired Source e Route wire from Safety Beam sensors to power head using method shown in Fig 4 5a e Securely fasten wires to wall and ceiling as you go Fig 4 6 on next page m Use insulated staples Staples should be snug only Dashed Line striped wire Solid Line white wire dE FIG 4 5a Source and sensor wiring methods PN 3642036212 8 09 2007 3b Wiring pre wired e Route wire from wall to Safety Beam sensors Fig 4 5b e Splice pre wiring to shortened sensor wire match wire pairs dash to dash and plain to plain Trim sensor wire to approximately one foot 1 ft from sensor Split and strip ends of sensor wires and pre wired wires Fig 4 7 Splice wires together with provided wire nuts e Route wire from ceiling to power head Wire Nut Fig 4 5b e Securely fasten wires where they exit wall and ceiling as you go Use insulated staples Staples should be snug only Insulated Staple CAUTION Staples which are too tight can cut or pinch wires Cut or pinched wires can cause the Safe
Download Pdf Manuals
Related Search