Generac 7500 Portable Generator User Manual
Contents
1. FIG 6 2 Engage Chain Belt Connector to Carriage CAUTION Operation of the opener without the Chain or Belt Connector engaged to the Carriage Assembly will result in damage to rail components including the rail pulley 02 26 2010 REV 1 DOOR gt The Carriage Lock can be manually engaged or gon A Eee disengaged To disengage Carriage Lock Pull handle downward opener power head o To engage Carriage Lock Pull handle towards door UNLOCK Lock TO RELEASE TO RECONNECT PULL TOWARD PULL TOWARD THE OPENER DOOR FIG 6 3 Engage Disengage Carriage Lock KEYED EMERGENCY RELEASE PURCHASED SEPARATELY Obtain standard emergency release kit and remove S hook from the cable end that attaches to the opener carriage 1 Attach the emergency release cable loop end to the opener carriage as shown FIG 6 4 Properly connecting the release cable to the carriage fitting will enable the correct carriage release action for the opener Improper connection of the emergency release cable to the opener carriage will result in a failure of the emergency release FIG 6 4 Emergency release cable to carriage 2 Follow the remaining installation instructions for the standard emergency release kit 3 Test for correct operation of emergency release kit Keyed Emergency Release Operation Instructions Place key in2. for longer life Screw 1 bulb into each socket 2 Lens Select a white lamp cover On the power head end nearest the garage door line up lamp lens tabs on power head with corresponding slots in lens Fig 9 1 Slide lens onto power head Make sure the tabs are fully engaged into lens slots Fig 9 2 Repeat for rear lens on power head Plug power cord back into electrical outlet Test lamp operation FIG 9 1 Slide each lens onto motor cover FIG 9 2 Fasten lens 24 PN 37026500123 02 26 2010 REV 1
3. slot Rotate and hold key while lifting garage door 1 to 2 inches Release key and continue opening garage door 21 OWN FORCE 4 By turning the Close Force Control clock wise the DOWN force can be increased By turning the Close Force Control counter clockwise the DOWN force can be decreased Set the DOWN force level at the minimum force required to close door without reversing 2 Once the desired level is selected this stores the necessary force level for the DOWN direction in memory By turning the Open Force Control clockwise the UP force can be increased By turning the Open Force Control counter clockwise the UP force can be decreased Set the UP force level at the minimum force required to open door without stopping 4 Once the desired level is selected this stores the necessary force level for the UP direction in memory p OPEN CLOSE TRAVEL LIMIT Press and hold both of the SET buttons E amp E together until the green indicator light blinks about 5 seconds All close and open travel limit settings are erased Then follow the steps above to reprogram close and open travel limits N TACT REVERSE TEST The force adjustments and limit switch settings MUST BE COMPLETED before testing 4 Testing Open garage door using Wall Control Place a 2 x 4 board laid flat under center of garage door opening FIG 6 6 Close door using
4. 20 16 DOIIE Severe injury or death can result if the door closing force is set too high Never increase the door closing force above the minimum required to move the door Never adjust force to compensate for a sticking or binding door Perform monthly CONTACT REVERSE TEST as described on page 22 and in Section 10 1643 OR WWW GENIECOMPANY COM Limit Controls location on power head NOTE Set Close Travel Limit before setting Open Travel Limit for unit to operate normally Unless limits are being reset do not press set limit buttons SETTING amp TESTING OPEN CLOSE LIMITS The OPEN UP and CLOSE DOWN door positions are controlled by making the adjustments on the panel located on the bottom of the power head The adjustments that can be made are Close Travel Limit Open Travel Limit Adjust Closing Force Adjust Opening Force Transmitter Programming A ENGAGE CHAIN BELT CONNECTOR TO CARRIAGE 1 Press and hold the Close Travel Limit El button until the chain or belt connector advances and engages to the Carriage Assembly Fig 6 2 B CLOSE TRAVEL LIMIT Press and hold the Close Travel Limit button until the door is fully closed You can quickly press and release the Close Travel Limi button to move the door in small increments You can also use the Open Travel Limit button to move the door slightly in the UP direction 3 Door is fully closed when the bottom edge
5. Limit Up Force tint SE yg Adjustment if N campeon D ser J LEARN MANUAL LIMIT FORCE gt ser X v Leah 4 Ae CODE cose Ome CLOSE Zumre Travel Limit Set Limit Control Button Adjustment FIG 7 1 Learn code button and LED PN 37026500123 02 26 2010 REV 1 23 ENT AND VISOR CLIP INSTALLATION Battery replacement To open gently push straight out on battery cover lock tab as shown Fig 8 1 Slide open battery cover Remove old battery Make sure new battery is facing proper direction Match battery polarity with symbols inside battery housing Fig 8 2 Recommended replacement battery type Alkaline A23 12 volt Slip new battery into place Slide battery cover until it clicks shut Operate remote to make sure it is working properly No re programming is needed 2 Visor clip The visor clip may come already installed You will have to install the visor clip if you choose to attach your remote to the car visor Slide visor clip into back of remote control It will snap into place Fig 8 3 and polarity marks ee FIG 8 2 Match battery polarity FIG 8 3 Attach visor clip A For added safety and protection please unplug opener before installing light bulb 1 Light bulb Recommendations Do NOT use a short neck bulb Light bulbs should be no more than 60 Watts Use a heavy duty service bulb
6. Wall Control When door contacts board the door must stop within 2 seconds and reverse direction returning to open position 2 Adjustment If the door does not properly reverse Check to see if door has close limit programmed It should not have reached its close limit before hitting board If the door STOPS but does not reverse decrease CLOSE FORCE control 2 setting slightly turn it counter clockwise Test again Repeat as necessary until door reverses upon contacting board PN 37026500123 FIG 6 5 Up Force OPEN Contr Adjustment FORCE Ne Decreasing Force rowe coun cocnSe CLOSE Bown Force Control Adjustment Force Control Adjustment FIG 6 6 2x4 under center of door opening 02 26 2010 REV 1 7 PROGRAMMING REMOTE CONTROLS t WARNING A moving door can cause serious injury or death 1 Keep people clear of opening while door is movin i 2 Do NOT allow children to play with opener including wall button remote control or Wireless Keypad During programming the door opener could begin to run so keep people and objects away from the moving door and See To keep the door from moving close the door and disconnect it from the Opener by pulling the Emergency Release NOTE For remote control locate Box 3 1a Single Button Remote Programming NOTE This opener can learn up to 7 transmitter buttons O Locate Learn Code button an
7. al received from the missing remote control or any other which has not been reprogrammed NOTE To program a Homelink and Car2U device follow the Homelink or Car2U instructions in your car owner s manual FCC and IC CERTIFIED This device complies with FCC Part 15 and RSS 210 of Industry Canada This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which may be determined by turning the equipment OFF and ON the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiver antenna Increase the separation between the opener and receiver Connect the opener into an outlet on a circuit different from that to which the receiver is connected Consult your local dealer Limit controls location on power head uD Open Indicator Light Set
8. d indicator LED on the power head Fi 7 1 Press and release Learn Code button Indicator LED will blink RED at a rate of twice er second Within 30 seconds push remote control button once Indicator LED will stop blinking and stay ON Press remote control button again Red LED will go out Remote is now programmed and ready for use Press remote control button again door will move 1b Multi Button Remote Programming NOTE Each button on a multi button remote is designed for use with 1 door You cannot program 2 buttons to operate the same door nor can you program 1 button to operate 2 doors You can program a maximum of 7 different transmitters or wireless devices NOTE Pushing two buttons on power head simultaneously will erase programmed memory and limits must be reset For each button Program each button separately using the Single Button Remote Programming steps 2 Operating e Press remote button once Door will move Press button again Door will stop Press button again Door will move in opposite direction NOTE The door will stop automatically at the fully open or fully closed position LOST OR STOLEN REMOTE 1 Clear memory Press and hold learn code button on power head for 10 seconds or until the red blinking indicator LED goes out Program remaining or new remote controls as done previously Your door opener will no longer recognize any sign
9. of door presses firmly onto the ground Once the door is in the desired position press and hold the Close SET Limit E button for 5 seconds The LED indicator light will blink green once This stores the closed position in memory C OPEN TRAVEL LIMIT 1 Press and hold the Open Travel Limit button to move the door to its fully opened position This starts the opener moving in the UP direction Hold the Open Travel Limit E button until the door is in the fully opened position that you desire then release this button 3 You can quickly press and release the Open Travel Limit button to move the door in small increments You can also use the Close Travel Limit amp button to move the door slightly in the DOWN direction Once the door is in the desired position press and hold the Open SET Limit E button for 5 seconds The LED indicator light will blink green twice This stores the opened position in memory PN 37026500123 uD Open IndicatorLight OPen Set Limit Teenie Suton oF i A SET Up Force OPEN Control Adjustment FORCE CLOSE Sonn force Control Adjustment t LEARN MANUAL KL je lj fr CODE cose LIMIT SET v Close Set Limit Button Travel Limit FIG 6 1 Limit controls CAUTION Failure to verify the engagement of the belt chain connector will result in damage to rail components
Download Pdf Manuals
Related Search