GE Monogram ZIC360N LH Refrigerator User Manual
Contents
1. Shut off the main water supply Turn on the nearest faucet long enough to clear the line of water Install a shut off valve between the icemaker water valve and cold water pipe in a basement or cabinet The shut off valve should be located where it will be easily accessible NOTE It is best to install the valve into a vertical water pipe If you install the valve into a horizontal water pipe make the connection at the top or side to avoid drawing off any sediment from the water pipe Drill a 1 4 hole in the water pipe Fasten the shut off valve to the pipe with pipe clamp Tighten the clamp screws until the sealing washer begins to swell Do not over tighten Place a compression nut and ferrule sleeve onto the end of the tubing and connect it to the shut off valve Make sure the tubing is fully inserted into the valve and ferrule is tightened Turn on the main water supply and flush debris Run about a quart of water through the tubing into a bucket Shut off water supply at the shut off valve Remove the four 7 16 bolts securing the straps to the skid CAUTION o NOT ATTEMPT TO ROLL UNIT OFF SKID Remove Tie Downs PRUDENCE d NE FAUT PAS ESSAYER DE FAIRE ROULER LE R FRIG RATEUR POUR L ENLEVER DE LAY PALETTE e Support blocks on the bottom of the refrigeration case must be removed before sliding unit off skid or damage will occur Carefully tilt refrigerator and slide blocks out2. 23 7 8 From Rear of Refrigerator T n co 3 4 Overlay Top View IO o E Panel Nominal Size 90 DOOR SWING optional setting Scale 1 1 Design Guide CUSTOMIZATION BASICS Framed Or Overlay Panels Custom Handles and Accessory Kits Models Available Stainless Steel Wrapped Models ZICS360N RH right handed door ZICS360N LH left handed door Trimmed models ZIC360N RH right handed door ZIC360N LH left handed door Stainless Steel Wrapped Refrigerators Stainless Steel wrapped refrigerators have wrapped doors and grille panel beveled edges and tubular stainless steel handles that coordinate with other Monogram appliances These models are shipped ready for installation Trimmed Refrigerators Trimmed refrigerators are designed to be customized with decorative panels Field installed custom door and grille panels are required Framed panels You may install 1 4 thick custom panels from your cabinet manufacturer The decorative panel slides into the factory installed trim Or order black white and stainless steel accessory panels from your Monogram dealer Standard Door Handle Framed Panel Standard supplied handles shown in 1 4 panel position Optional Accessory Kits ZKHCSS2 Monogram Tubular Stainless Steel handles designed to fit framed or overlay panels ZUG2 For side by side installation of two trimmed bottom freezer refrigerat
3. 1 4 open end wrench Pliers HARDWARE SUPPLIED Water filter bypass plug Anti Tip brackets Special 3M Dual Lock adhesive strips for 1 4 side panels 4 nut and ferrule GROUNDING THE REFRIGERATOR IMPORTANT Please read carefully FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERLY GROUNDED The power cord of this appliance is equipped with a three prong grounding plug which mates with a standard three prong grounding wall receptacle to minimize the possibility of electric shock hazard from this appliance Have the wall outlet and circuit checked by a quali fied electrician to make sure the outlet is properly grounded Where a standard 2 prong wall outlet is encountered it is your personal responsibility and obligation to MATERIALS REQUIRED 35 long 2x4 for Anti Tip support Copper water line tubing Water shut off valve optional but recommended Custom panels for fresh food door freezer drawer and grille panel e Screws to secure refrigerator to cabinetry FLOORING For proper installation this refrigerator must be placed on a level surface of hard material that is at the same height as the rest of the flooring This surface should be strong enough to support a fully loaded refrigerator or approximately 700 Ibs NOTE Protect the finish of the flooring Cut a large section of the cardboard carton and place under the refrigerator where you are working have it replaced with a pr
4. Minimum to Wall 430 u Ww di non E 4 Minimum to Wall Allow 25 minimum clearance for a full 130 door swing Allow 15 for pan removal 4 minimum clearance is required when door swing is adjusted to 90 If the 90 door stop position is used pan access is maintained but pan removal is re stricted bottom pans See illustrations pages 4 and 5 to determine door swing interaction with adjacent cabinets or countertops qoo 1 1 2 Finished Width 31 25 16 Tr 2 Electrical 24 9 16 Wall View m a7 10 ET 24 Cutout 34312 om Depth Floor to Bottom of Electrical 9t Water Supply Water Supply 54 Y Y i y x Y N 4 N 3 1 2 3 1 2 Design Guide 23 7 8 From Rear of Refrigerator Refrigerator Case Trim __ 2 Eod N a 1 i i 1 i 1 1 1 1 md L 1 a 1 1 1 1 Ax Sean 1 1 i 1 Li 1 a 1 1 LI 1 a a BEE Eee 1 1 1 d 1 1 1 BL ER Hcc 1 1 1 DUE EDEN 1 i EE i gt em ni 7 LES ina 2 4 rd E o AU y t z N N za Y N Ww 3 4 Overlay Panel Nominal Size SON y y x s s y y x y y y S y y 4 y naien y y Door 130 DOOR SWING factory setting Top View Scale 1 1 bDesignGude 0 Refrigerator k Case Trim
5. carpentry and plumbing skills Proper installation is the responsibility of the in staller Product failure due to improper installation is not covered under the GE Appliance Warranty See the Owner s Manual for warranty information WARNING These refrigerators are top heavy and must be secured to prevent the possibility of tipping for ward Anti Tip protection is required See page 11 for details Use this appliance only for its intended purpose Immediately repair or replace electric service cords that become frayed or damaged Unplug the refrigerator before cleaning or making repairs Repairs should be made by a qualified service technician AVERTISSEMENT Ces r frig rateurs sont lourds en haut et il faut les arrimer pour viter leur basculement Il faut avoir un syst me de protection contre le renversement Voir les d tails page 11 Il ne faut utiliser cet appareil que pour l utilisation appropri e R parer ou remplacer imm diatement tout cordon lectrique effiloch ou endommag e Il faut d brancher le r frig rateur avant le nettoyage ou toute intervention Les r parations doivent tre faites par un technicien qualifi For Monogram local service in your area 1 800 444 1845 For Monogram service in Canada 1 888 880 3030 For Monogram Parts and Accessories call 1 800 626 2002 www monogram com Installation Instructions Tools Hardware Materials Grounding the Refrige
6. cover trim and lift off Use pliers to unscrew door stop and reinstall into the 90 position 0 F 1 oO III Remove Wire Cover Trim Screws Pin Location For 90 Door Swing Pin Location as Shipped 130 Door Swing Reinstall the wire cover trim 13 STEP 8 INSTALL GRILLE PANEL Raise the grill panel to stop position Raise Grille Panel O IN Adjust Nut Below Spring to Accommodate Panel Weight de Loose screws on side trim behind frame Remove bottom trim Slide panel over the metal baker panel and into the trim If necessary tap with a wood block until panel slips under the top trim piece Reassemble bottom trim Tighten screws Adjust the hinge spring to accommodate the panel weight if necessary Installation Instructions INSTALL FRAMED PANELS to Secure Trim Use Rear Holes to Secure Handle Install door and drawer panels Open door to 90 Remove the 4 Phillips head screws from the door handle Remove handle Retain all screws Remove 4 screws holding trim lift off trim Retain screws Slide framed panel into the door trim Custom handles If you are using custom handles the handle must be properly secured to the
7. lift off trim Retain screws Slide overlay panel into the door trim Custom handles If you are using custom handles the handle must be properly secured to the panel before sliding the panel into the trim The cabinet manufacturer will supply the custom handle and hardware Secure the door drawer trim using both the FRONT and REAR screw holes Discard supplied handle There are two sets of holes in the handle side trim Replace handle side trim by installing the original screws in the REAR screw holes Secure the handle to the door using the FRONT screw holes Follow the same procedures to install the drawer panel 15 Installation Instructions STEP 10 CONNECT WATER SUPPLY Check to be sure that refrigerator power cord is not plugged into the wall outlet House Refrigerator Water Supply Water Supply Locate and bring copper tubing to the front of the cabinet Turn the water on to flush debris from line Run about a quart of water through tubing into a bucket then shut off water e Slip a 1 4 nut and ferrule provided over both ends of the copper tubing Insert tube into the union fitting on the unit and tighten nut to union Turn on the water to check for leaks Note Make sure excess tubing length does not interfere with drawer closing or toekick installation STEP 11 CONNECT POWER Connect refrigerator power cord plug to a properly
8. panel before sliding the panel into the trim The cabinet manufacturer will supply the custom handle and hardware e Secure the door drawer trim using both the FRONT and REAR screw holes Discard supplied handle Right hand models shown Use the same instructions for left hand models IF YOU ARE INSTALLING OVERLAY PANELS GO TO STEP 9A Door Trim Refrigerator Door 14 Standard supplied handle shown in 1 4 panel position There are two sets of holes in the handle side trim Replace handle side trim by installing the original screws in the FRONT screw holes e Secure the handle to the door using the REAR screw holes Follow the same procedures to install the drawer panel Installation Instructions E STEP 9A INSTALL OVERLAY PANELS Right hand models shown Use the same instructions for left hand models Door Trim Refrigerator Door Use Front Holes to Secure Handle Use Rear Holes to Secure Trim Supplied handle shown in the overlay panel position Install door and drawer panels Open door to 90 Remove the 4 Phillips head screws from the door handle Remove handle Retain all screws Remove 4 screws holding trim
9. Installat on Instructions If you have questions call 800 626 2000 or visit our website at www monogram com ZIC360N RH ZIC360N LH ZICS360N RH ZICS360N LH Built In Bottom Freezer Refrigerators Design Guide With Installation Instructions Monogram We bring good things to life Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully IMPORTAN T Save these instructions for local inspector s use Observe all governing codes and ordinances e Note to Installer Be sure to leave these instruc tions with the Consumer Note to Consumer Keep these instructions with your Owner s Manual for future reference WARNING This appliance must be properly grounded See Grounding the Refrigerator page 9 AVERTISSEMENT Cet appareil doit tre correctement mis la terre Consulter Mise la terre du r frig rateur page 9 If you received a damaged refrigerator you should immediately contact your dealer or builder CAUTION Due to the weight and size of this refrigerator and to reduce the risk of personal injury or damage to the product TWO PEOPLE ARE REQUIRED FOR PROPER INSTALLATION PRUDENCE cause du poids et de la taille de ce r frig rateur et pour r duire le risque de blessure et de dommages IL FAUT DEUX PERSONNES POUR FAIRE L INSTALLATION CORRECTEMENT CONTENTS Skill Level Installation of this refrigerator requires basic mechanical
10. circuit or circuit breaker is recommended Install a properly grounded 3 prong electrical receptacle recessed into the back wall Electrical must be located on rear wall as shown Note GFI ground fault interrupter is not recommended Water line can enter the opening through the floor or back wall The water line should be 1 4 O D copper tubing between the cold water line and water connection location long enough to extend to the front of the refrigerator Installation of an easily accessible shut off valve in the water line is recommended ZUG2 ZUGSS2 Unified Grille Panel Kit f you are installing two refrigerators side by side the installation space must be 71 1 2 wide Note Additional cutout width may be required when side panels are used Add side panel thickness to the finished cutout to calculate rough in width The water and electrical locations for each product must be located as shown A separate 115V 60Hz 15 or 20 amp power supply is recommended for each product T DIMENSIONS AND E CLEARANCES _ gt la Shipping height The height may be adjusted from 83 1 2 to 84 1 2 by adjusting leveling legs and wheels Product Clearances These refrigerators are equipped with a 2 position Frame to Frame door stop The factory set Width 130 door swing can be adjusted to 90 if clearance to adjacent cabinets or walls is restricted 130 Door Swing 90 Door Swing 25
11. from beneath slide unit off skid Remove toekick Set aside for final installation Floor Copper Tubing Compression Nut Saddle Type Shutoff Valve Outlet Valve Ferrule Sleeve NOTE Saddle type shut off valves are included in many water supply kits Before purchasing make sure a saddle type valve complies with your local plumbing codes NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted in Massachusetts Consult with your licensed plumber Installation Instructions STEP 2A WATER LINE INSTALLATION WITH A REVERSE OSMOSIS SYSTEM Skip this step when not using an RO System If the water supply to the refrigerator is from a Reverse Osmosis Water System use the refrigerator s filter bypass plug Using the refrigerator s water filtration cartridge with the RO filter can result in hollow ice cubes Filter Bypass Plug STEP 3 INSTALL SIDE PANELS Skip this step when not using side panels If you are using 1 4 side panels they should be inserted into the case trim Fasten the panels to the refrigerator with the 3M Dual Lock adhesive strips provided before setting refrigerator in place STEP 4 INSTALL ANTI TIP BRACKETS WAR N l N G ANTI TIP PRECAUTIONS The refrigerator is top heavy and must be secured to prevent the possibility
12. grounded receptacle accessible through the top left side of the grille opening Electrical Sabbath Light Outlet Switch Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on The temperature controls are preset at 37 F for the fresh food section and OF for the freezer Allow 24 hours to stabilize before making adjustments STEP 12 START ICEMAKER Flip the switch to I ON The icemaker will begin operation automatically Be sure nothing interferes with the sweep of the feeler arm Discard the first full bucket of ice cubes To turn the icemaker off set the switch to O OFF STEP 13 INSTALL TOEKICK e Locate the supplied toekick shipped taped to the side of the refrigerator Install with 2 screws provided adjust to desired height and tighten screws e A custom toekick can be installed to match or complement the surrounding cabinetry Use the supplied toekick as a template to cut out the notch and vent holes Supplied Toekick Do D UN E 1 4 or Thicker Toekick gt Important The vented toekick must remain unob structed for proper air circulation and refrigerator operation Notes 17 Notes Notes Note While performing installations described in this book safety glasses or goggles should be worn TM F
13. ker panel left to right and top to bottom Secure the panels with glue e Center the spacer and backer panel on the overlay panel and secure with glue and screws Screws must be NOTE Left to right offset is not always equal to countersunk into the backer panel top to bottom offset Design Guide SIDE PANELS ZUG2 GRILLE PANEL DIMENSIONS Side panels must be used whenever the sides of the The ZUG 2 unified grille panel kit provides for the refrigerator will be exposed The 1 4 side panels will installation of a framed or overlay grille panel slip into the side case trim Order the side panels from the cabinet manufacturer k A Grille Panel l 24 9 D di Framed Panel Dimensions i spen On A Width B Height installation height 1 4 Framed Panel 69 7 8 8 7 8 Overlay Panel Dimensions A Width B Height 1 4 Backer Panel 69 7 8 8 7 8 0 10 Spacer Panel 68 1 2 7 5 8 3 4 Overlay Panel 70 1 8 9 a Panel RE Spacer Panel d gt y Backer Panel ES Assemble the overlay panels in the same manner as the door and drawer panels Installation Instructions TOOLS REQUIRED Tinsnips to cut banding Stepladder Bucket Level Appliance Hand Truck Tubing cutter 7 16 open end wrench 2 Phillips screwdriver Drill and appropriate bits 5 16 7 16 socket e Safety glasses 1
14. nsions shown The panels will slide Door Drawer Reveal into the frame on the door drawer and grille l l 1 1 l 1 1 1 1 If the custom panel is less than 1 4 thick and if it fits loosely in the door frame it can be backed up with a piece of filler material or foam tape to improve the fit X IMPORTANT NOTE Maximum weight for fresh food panel is 50 pounds and 30 pounds for freezer drawer panel A Grille Panel Framed Panel Dimensions A Width B Grille Height C FF Height D FZ Height 1 4 Framed Panel 33 1 8 8 7 8 46 1 16 21 7 8 Fresh Food Panel Overlay Panel Dimensions A Width B Grille Height C FF Height D FZ Height Freezer Diei 1 4 Backer Panel 33 7 8 8 7 8 46 1 16 21 7 8 Panel 0 10 Spacer Panel 32 1 2 7 5 8 44 11 16 20 1 2 3 4 Overlay Panel 34 1 8 9 46 5 16 22 3 4 OVERLAY PANEL DIMENSIONS Overlay Panel Door Drawer F Overlay or a more custom appearance overlay panels may be installed on trimmed models The overlay panel must i be secured to a 1 4 thick backer panel which slides into the trim A spacer panel 0 10 thick must be placed between the overlay and backer panel Panel IMPORTANT NOTE Mazimum total weight for assembled fresh food panel is 50 pounds and 30 pounds for freezer drawer panel 1 4 Assemble the panels with glue and screws EE Eo e Center the spacer panel on the bac
15. of tipping forward ATTENTION precautions contre Les BASCULEMENTS Le r frig rateur est beaucoup plus lourd en haut et il faut le maintenir en place pour viter la possibilit de son basculement vers l avant e Cut a 2 x 4 x 35 block and secure the block to the mounting brackets provided using 12 or 14 wood screws Mounting Bracket 2 x 4 Cut B To 35 Length y y Installation Height From Floor Wood Screws Mounted io 7 Vertical Wood Studs Secure the bracket with wood block to the back wall so that it is 84 or your installation height from the finished floor See illustration Brackets Required Block d Soffit Brackets Not Required Y Beneath a Height Soffit From Floor to Bottom of Wood Block Side View Screws must penetrate at least one inch into vertical wall studs Gently push refrigerator into the opening with hands against front corners Important Note When the refrigerator is installed under a soffit or if there is not enough height for this method of security brackets cannot be used Proceed to step 5 to level the refrigerator and then to step 6 to secure refrigerator to cabinets The refrigerator must be secured to prevent tipping Installation Instructions STEP 5 LEVEL REFRIGERATOR All models have 4 point leveling The front is sup ported by leveling legs the rear is su
16. operly grounded 3 prong wall outlet DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD GROUND PRONG FROM THE POWER CORD DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR TO A 2 PRONG OUTLET DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE Installation Instructions STEP 1j REMOVE PACKAGING CAUTI 0 N Refrigerator is much heavier at the top than at the bottom be careful when moving When using a hand truck handle from side only PRU D EN CE Le r frig rateur est beaucoup plus lourd en haut qu en bas Il faut tre prudent lors des d placements Si un diable est utilis il faut soulever le r frig rateur sur le c t seulement Carefully cut banding at the top and bottom remove outer carton Slide out back corner posts 2 Slide carton off top of cabinet NOTE IT IS NOT NECESSARY TO LAY CABINET DOWN IN ORDER TO REMOVE SKID The unit is secured to the skid with 4 slotted tie down straps Remove the four 5 16 bolts from the base channels in the tie downs STEP 2 INSTALL WATER LINE A cold water supply is required for automatic ice maker operation The water pressure must be be tween 40 and 120 p s i Route 1 4 OD copper tubing between house cold water line and the water connection location Copper tubing should be long enough to extend to the front of the refrigerator Allow enough tubing to accommodate bend leading into the water line connection
17. or Monogram 1 800 444 1845 Note Product improvement is a continuing endeavor at General Electric Therefore materials appearance and specifications are subject to change without notice local service in your area call Pub No 49 60136 M amp Dwg No 164D4371P001 onogram N D 729A 11 01 General Electric Company 75260 Louisville KY 40225
18. ors This kit provides for the installation of a unified custom grille panel to span the width of two units using a framed or overlay panel ZUGSS2 For side by side installation of two stainless steel wrapped bottom freezer refrigerators This kit provides a unified stainless steel grille panel to span the width of two units Overlay panels You may also choose to install custom overlay panels from your cabinet manufacturer This design provides a seamless appearance which integrates smoothly with surrounding cabinetry 3 4 Overlay Panel 10 Thick Spacer Panel 1 4 Thick Backer Panel Standard Door Handle Standard supplied handles shown in 3 4 overlay panel position Door and Drawer Handles The standard supplied handles can be adjusted to accommodate both framed or overlay panels Custom handles of your choice supplied by your cabinet maker can also be installed If desired you may order ZKHCSS2 Monogram stainless steel tubular handle kit Side Panels Side panels must be used whenever the sides of the refrigerator will be exposed Accessory Panels White black and stainless steel accessory panels are available from your Monogram dealer Panels are cut to size and ready to install ZPBC360 Black ZPWC360 White ZPSC360 Stainless Steel Panels Design Guide 1 4 FRAMED PANEL DIMENSIONS If you choose to install framed panels they must be ae cut to the dime
19. pported by adjustable wheels Both are accessible from the front of the refrigerator To level the back of the refrigerator turn the 7 16 hex nut located above the front wheels Turn clockwise to raise or counterclockwise to lower the refrigerator For front leveling use a 1 1 4 open end wrench Adjust height of refrigerator to match installation cutout opening 83 1 2 to 84 1 2 The refrigerator should be level and plumb with cabinetry Hex Nut Adjusts 4 Rear Wheels E Leveling AW 12 STEP 6 SECURE REFRIGERATOR TO CABINETRY Whenever possible perform this step for anti tip security or when anti tip brackets cannot be used The refrigerator must be secured to prevent tipping Raise the grille panel to access case trim Drill hole in trim and drive screw through the trim into adjacent cabinet Follow the same procedure on the opposite side Drive Screws Through Case Trim and Into Adjacent Cabinets Installation Instructions STEP 7 ADJUST DOOR SWING NOTE This refrigerator has a 2 position door stop When space does not allow the door to swing open fully to 130 you may change the door swing to a 90 opening Skip this step if door opening is satisfactory for your installation situation Lift the grille panel to access the wire cover trim Remove screws on both sides of the wire
20. rator Step 1 Remove Packaging Step 2 Install Water Line Step 2A RO Water Line Step 3 Install Side Panels Step 4 Install Anti Tip Brackets Step 5 Level Refrigerator Step 6 Secure Refrigerator to Cabinetry 12 Planning Guide The Installation Space Dimensions and Clearances 130 Door Swing 90 Door Swing Customization Basics Panel Dimensions Side Panels ZUG2 Grille Panel Dimensions Step 7 Adjust Door Swing Step 8 Install Grille Panel Step 9 Install Framed Panels Step 9A Install Overlay Panels Step 10 Connect Water Supply Step 11 Connect Power Step 12 Start Icemaker Step 13 Install Toekick Design Guide THE INSTALLATION SPACE The finished cutout width must be 35 1 2 35 1 2 Finished Width 25 16 Wall View EH m 10 Electrical Area 84 1 2 max 83 1 2 min nid Finished 24 Cutout Depth Opening 74 1 2 From Floor to Bottom of Electrical p Water Supply ES 317 3 aes Water And Electrical Locations The opening must be prepared with the electrical and water supply located as shown The cutout depth must be 24 Designed for industry standard flush installation The refrigerator will project forward slightly beyond adjacent cabinetry depending on your installation Additional Specifications e A 115 volt 60Hz 15 or 20 amp power supply is required An individual properly grounded branch
Download Pdf Manuals
Related Search