GE GNUT03B Water Dispenser User Manual
Contents
1. Q 2 type as required if mounting hole is needed for faucet Water supply saddle valve CAUTION To avoid damaging the sink consult Filtered water faucet for sink or countertop a qualified plumber or installer for drilling mounting procedures Special drill bits may be needed 3 8 tubing and fittings to make all needed for porcelain or stainless steel connections Sump wrench Installation Overview Fig 1 Locate the drinking water Filtered water faucet CK Washer sdij Buijoousajqnoa system on the cold water Adapter supply pipe under the Water kitchen and or bathroom 4 sink to filter the cold drinking water Water supply saddle valve Mounting PP screw 2 C NE Hot Cold Insert f Shutoff valve Nut NOTE To change the filter cartridge you Filter II must turn off the water nearby shutoff N Tubing gt valve is convenient Most sinks already have i EN gt 9 shutoff valves on the supply pipes Step by step installation instructions Feed Water Supply Check and comply with local plumbing codes as you plan then install a cold feed water supply fitting For new home installation using standard plumbing fittings see Fig 2A below A typical installation for existing homes using the saddle valve is shown in Fig 2B below A PREFERRED INSTALLATION Turn off the cold water supply 2 Com2. Q 3 8 tubing run to Filter II outlet Lock washer 5 Hexnut 5 Plastic washer sdij 2 Step by step installation instructions Mounting Bracket to Cabinet Wall The bracket can be used as a template for marking the location of the mounting screws When determining the location of the bracket make sure you leave 1 1 2 to 2 of free area under the sumps to allow for sump removal and enough space on either side to make the tubing connections Make Tubing Connections Safety Instructions Run the length of 3 8 tubing connected to the bottom of faucet to the filter system outlet Fig 1 in the Installation Overview section Allow enough slack in the tubing to be able to place the system on the floor in front of the sink Measure and cut the end of the tubing square Slide a compression nut onto the end of the tubing and push a tubing insert into the tubing Connect the tubing and tighten the compression nuts securely Repeat the preceding steps to connect a length of tubing between the filter system inlet and the water supply saddle valve Fig 1 in the nstallation Overview section Fig 4 Operating Instructions Tubing connector Filter IT Filter I 1 2 to 2 Filter Cartridge Installation or Replacement o b gt p Mounting N N Q bracket 22
3. 3 8 X 20 FT WH NUT 3 8 ADAPTER TUBING WASHER SADDLE VALVE SUPPLY FAUCET ASM FILTER TASTE amp ODOR FILTER SEDIMENT WRENCH SUMP PM MANUAL USE amp CARE INSTALLATION Uo Oi c C E CKO Lm mx eh nh m n h2 h2 h2 h9 F2 OO Lm rE eb m n h2 OO Safety Instructions Operating Instructions Installation Instructions Troubleshooting Tips Customer Service 7 Notes 18 541 Buigoouso qno4 INAS DA 5 suomanijsu Ajojeg suomanasu Guneiadg suonanajsu uomej ejsu GE Water Filtration System Warranty For service call 800 GE CARES A For The Period Of GE Will Replace One Year From the date of the original purchase What GE Will Not Cover Service trips to your home to teach you how to use the product Inproper installation Failure of the product if it is abused misused or used for other than the intended purpose or used commercially Use of this product where water is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts All warranty service provided by our SmartWater Authorized Servicer Network Any part of the Water Filtration system excluding filters which fails due to a defect in materials or workmanship During this imited
4. GE Appliances Water Filtration System Owner s Manual and Installation GNUTO3B GXUTO3B Faucet GNUTOS3B and GXUTOSB are Tested and Certified by NSF International against ANSI NSF Standard 42 for Particulate Reduction Class I Chlorine Reduction Class I and Taste and Odor Reduction Part No 215C1044P002 1 Pub No 49 50006 2 3 9 Jf 7205677 Safety Instructions Operating Instructions o S S 2 c A Troubleshooting Tips rvice Customer Se Safety Information 3 Operating Instructions 4 7 Specification Guidelines 4 Using the System 5 Filter Cartridge Replacement 2 Flush Procedure 6 Installation Instructions 7 11 Important Recommendations lools Materials Required Step by Step Instructions 8 11 Feed Water Supply 8 Faucet Installation 9 Wall Mounting 10 Tubing Connection 10 Filter Cartridge Replacement 10 11 Troubleshooting Tips Before You Call For Service 12 Customer Service Product Registration 13 14 15 16 ates cee es 19 Service Telephone 20 Congratulations You are Now Part of the GE Family Welcome to the GE family We re proud of our quality products and we are c
5. a Mounting v Tubing 7 amp connector 3 M 9 Q Sump sump 12 E 5 CAUTION Never remove sumps with water pressure in the Water Filtration system Close the water supply saddle valve Fig 1 and 2A to the filter Open the filtered water faucet Turn the sump off of the filter head as shown use the sump wrench provided Be careful the sump is full of water Locate and save the large o ring seal Remove and discard the used filter cartridge 9 gt S S o 5 S Be sure the inside of the sump is clean Thoroughly wash with hot soapy water and rinse Remove the wrapper and labels from the new filter cartridge and insert the filter cartridge in the sump Some cartridges fit either way while others fit only one way Observe markings on the end of the cartridge The sediment FXUSB filter cartridge should always be placed in the Filter sump rvice Lightly lubricate the o ring seal in the sump with clean silicone grease Be sure it is fully seated in its groove A Hold the sump up to the filter head aligning the center hole in the cartridge with the protrusion on the bottom of the head NOTE If the sump will not tighten up to the head you may have the cartridge in upside down Take the cartridge out and check the markings on the end of the cartridge for correct orientation Customer Se Being careful not to cross thread turn the sump onto the filter head and hand tig
6. des as you install the Water Filtration system Use the Water Filtration system on a potable safe to drink home COLD water supply only The filter cartridges will not purify water or make unsafe water safe to drink DO NOT use on HOT water 100 max suoianijsu Ajajes Bi Protect the Water Filtration system and piping from freezing Water freezing in the system will damage it Your Water Filtration system will withstand up to 125 psi water pressure If your house water supply pressure Is higher than 100 psi during the day it may reach higher levels at night install a pressure reducing valve before the system WARNING Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system The water should be tested periodically to verify that the system is performing satisfactorily Small parts remaining after the installation could be a choke hazard Discard safely Tools and Materials Required for Installation Slotted and Phillips screwdrivers Contents included with the product Pliers and adjustable jaw wrench Water filter assembly including mounting bracket and screws Hand or battery powered drill and 1 4 bit saddle valve installation Product Literature Owner s Manual and B Meciiedall and dull bio dail L4 hele Installation Product Data Sheet Owner Product S S 2 S Y 52 D
7. ds Service 800 626 2000 800 TDD GEAC 800 833 4322 GE offers free of charge a brochure to assist in planning a barrier free kitchen for persons with limited mobility Operating Instructions Service Contracts 800 626 2224 Purchase a GE service contract while your warranty is still in effect and you ll receive a substantial discount GE Consumer Service will still be there after your warranty expires Parts and Accessories 800 626 2002 Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes VISA MasterCard and Discover cards are accepted Installation Instructions Instructions contained in this manual cover procedures to be performed by any user Other servicing generally should be referred to qualified service personnel Caution must be exercised since improper servicing may cause unsafe operation Service Satisfaction If you are not satisfied with the service you receive from GE First contact the people who serviced your appliance Troubleshooting Tips Next if you are still not pleased write all the details including your phone number to Manager Customer Relations GE Appliances Appliance Park Louisville KY 40225 Q z Finally if your problem is still not resolved write Major Appliance Consumer Action Program 20 North Wacker Drive Chicago IL 60606 Customer Se Printed in Louisville KY
8. e money Review the chart below first and you may not need to call for service Problem Possible Causes Water contains tiny New filter cartridges contain black particles activated carbon which is a harmless black powder Water has air bubbles Air in system after installation and is cloudy Chlorine taste and or The filter cartridges are no odor in the product water longer removing chlorine from the water supply 72 What To Do e Turn on the filtered water faucet and allow these harmless carbon particles to purge from the cartridge Turn off the faucet when the water is clear Will go away after water runs for a while e Replace both filter cartridges GE Service Protection Plus GE a name recognized worldwide for quality and dependability offers you Service Protection Plus comprehensive protection on all your appliances No Matter What Brand Benefits Include Backed by GE We ll Cover Any Appliance All brands covered Unlimited service calls Anywh ere Anytim e id All parts and labor costs included No out of pocket expenses No hidden deductibles One 800 number to call You will be completely satisfied with our service protection or you may request your money back on the remaining value of your contract No questions asked It s that simple Protect your refrigerator dishwasher washer and dryer range TV VCR and much more any brand Plus there s no extra charge for emer
9. gency service and low monthly financing is available Even icemaker coverage and food spoilage protection is offered You can rest easy knowing that all your valuable household products are protected against expensive repairs Place your confidence in GE and call us in the U S toll free at 800 626 2224 for more information brands covered up to 20 years old in the continental U S Please place in envelope and mail to General Electric Company Warranty Registration Department P O Box 34070 Louisville KY 40232 4070 15 Consumer Product Ownership Registration Dear Customer Thank you for purchasing our product and thank you for placing your confidence in us We are proud to have you as a customer Follow these three steps to protect your new appliance investment Complete and mail After mailing Read your Owner s your Consumer the registration Manual carefully Product Ownership below store this It will help you Registration today document in a safe operate your new Have the peace of place It contains appliance properly mind of knowing we information you If you have questions can contact you in will need should or need more the unlikely event of you require service information call the a safety modification Our service number GE Answer Center is 800 5 800 626 2000 800 432 2737 Model Number Serial Number un d La d a a ua J Important If you did not get a
10. hten securely see Fig 5 10 CAUTION If using the sump wrench to tighten the sump do not overtighten Repeat steps 2 through 7 for the taste odor FXUTB filter cartridge in the Filter Il sump 9 Open the filtered water faucet Then slowly open the water supply saddle valve and allow the filter housing to fill Close the filtered water faucet Then check for leaks between the sump and the head suoianijsu Ajajes NOTE If leaking turn off the water supply and open the filtered water faucet Then disassemble the filter and check the o ring for cuts flat spots etc and sealing surfaces for foreign material Clean the o ring and lubricate with clean silicone grease Carefully press into the groove in the sump The filter cartridges contain activated carbon When new open the filtered water faucet for ten minutes to flush the system e bracket TU 8 jN HELL Head ee Cartridge Cb Replacement label TURN SUMP TO REMOVE Filter I Sump O ring seal TURN SUMP Sump Nl LA TO INSTALL loosen e S a S gt 2 D Q sdij 2 71 Safety Instructions Operating Instructions t S 5 S p S Troubleshooting Tips rvice Customer Se Before you call for service Troubleshooting Tips Save tim
11. it only one way Observe markings on the cartridge NOTE The Water Filtration system uses two different types of filter cartridges Be sure to install them correctly The sediment FXUSB filter cartridge should always be placed in the Filter sump 6 Lightly lubricate the o ring seal in the sump with clean silicone grease Be sure it is fully seated in its groove Hold the sump up to the filter head aligning the center hole in the cartridge with the protrusion on the bottom of the head Being careful not to cross thread rotate the sump onto the filter head and tighten securely by hand NOTE If the sump will not tighten up to the head you may have the cartridge in upside down Take the cartridge out and check for correct orientation 2 Repeat steps 2 through 8 for the taste odor FXUTB filter cartridge in the Filter IT sump Turn on the filtered water faucet Then slowly open the water supply saddle valve and allow the filter housing to fill Close the filtered water faucet Then check for leaks between the sump and the head NOTE If leaking turn off the water supply and turn on the filtered water faucet Disassemble the filter and check the o ring for cuts flat spots etc and sealing surfaces for foreign material Clean the o ring and lightly lubricate with clean silicone grease Carefully press into the groove in the sump The filter cartridges contain activated carbon When new turn on the filtered wa
12. n the system If your house water supply pressure is higher than will damage it Do not attempt to treat water 100 psi install a pressure reducing valve before over 100 installing the Water Filtration system WARNIN G Discard all unused and packaging material after installation Small parts remaining after installation could be a choke hazard Vig Read and follow this Safety Information carefully P af ON SAVE THESE INSTRUCTIONS suon nnsuj Ajajes gt a Q Q 2 gt D Q S 5411 Burjoousajqnoj 9249 JAUIOJSN Safety Instructions t 2 c 5 S S t S 5 S S Troubleshooting Tips rvice Customer Se Specification guidelines Many bad tastes and or odors are removed from water using activated carbon filter cartridges They are most often used to remove a chlorine taste and odor They can also reduce other undesirable elements from drinking water supplies such as organic chemical contaminants and lead NOTE Small amounts of hydrogen sulfide noticeable as rotten egg odor may be reduced by taste and odor filters for a short time but the carbon media is quickly exhausted Other water conditioning equipment is usually required for the continuous treatment of hydrogen sulfide The Water Filtration system uses two filter cartridges Filter I FXUSB a sedimen
13. ommitted to providing dependable service You ll see it in this easy to use Owner s Manual and you ll hear it in the friendly voices of our customer service department Best of all you ll experience these values each time you use the Water Filtration system That s important because your new system will be part of your family for many years And we hope you will be part of ours for a long time to come We thank you for buying GE We appreciate your purchase and hope you will continue to rely on us whenever you need quality appliances for your home O 2 2 22 Fill out and return the Consumer Product Registration Card that is packed with this product If you cannot find it please send in the duplicate card printed in the back of this manual FOR YOUR RECORDS Write the model and serial numbers here You can find them on the sump bracket Staple sales slip or cancelled check here Proof of the original purchase date is needed to obtain service under the warranty READ THIS MANUAL Inside you will find many helpful hints on how to use and maintain your water system properly Just a little preventive care on your part can save you a great deal of time and money over the life of your system IF YOU NEED SERVICE You ll find many answers to common problems in the Before You Call For Service section If you review our chart of Troubleshooting Tips first you may not need to call for
14. one year warranty GE will also provide free of charge all labor does not include service trip to home to replace the defective part Filter cartridges Replacement of house fuses or resetting of circuit breakers Damage to the product caused by accident fire floods or acts of God Incidental or consequential damage to personal property caused by possible defects with this appliance This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA In Alaska the warranty excludes the cost of shipping or service calls to your home Some states do not allow the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state To know what your legal rights are consult your local or state consumer affairs office or your state s Attorney General Warrantor General Electric Company Louisville KY 40225 suoianisu Ajajes suomanasu a S 3 m A S o sdij Burjoousajqnoa 1 WOJSNI GIINI Service Telephone Numbers GE Answer Center 800 626 2000 The GE Answer Center is open 24 hours a day 7 days a week Safety Instructions In Home Repair Service 800 GE CARES 800 432 2737 Expert GE repair service is only a phone call away Special Nee
15. plying with plumbing codes install a fitting on the cold water pipe to adapt 3 8 OD tubing typical connection is shown in Fig 2A parts not included Make sure a water supply valve is used Safety Instructions Fig 2A Preferred water supply connection using compression fitting Typical location Operating Instructions 3 8 tubing to inlet B OPTIONAL INSTALLATION Where codes permit NOTE Codes in the state of Massachusetts require installation by a licensed plumber and do not permit the use of the saddle valve For installation use plumbing code 248 CMR of the Commonwealth of Massachusetts Turn off the cold water supply 2 Close the water supply valve by Open the main water supply t S S E 45 22 A and attach saddle valve as turning the handle clockwise valve and several house E shown in Fig 2B faucets to purge air from the gt DANGER To protect yourself system Close faucets when Fomei nC HEIL water runs smoothly jury shock use a battery powered hand drill only to make the amp hole DO NOT USE AN ELECTRIC DRILL E Fig Optional water supply connection using saddle valve Pre drill 1 4 hole Seal make sure the seal is in place Nut 2 not required if holes in clamp are threaded a lt lt Clamp X Q ed rvice Clamp Z O Handle Tubing adapter _ Compression nut gt G
16. registration card with your product detach and return the form below to ensure that your product is registered ee Ap Cuter LLL Consumer Product Ownership Registration Model Number Serial Number Ms Mrs Miss First Name Last Name Street Address Zip State Code Date Placed In Use Day Year Phone Number i 7 Month HOTPOINT RGA GE Appliances General Electric Company Louisville Kentucky 40225 14 Safety Instructions Operating Instructions Installation Instructions Troubleshooting Tips Customer Service 72 pacem 090856 4 gt i gt 2 Parts List Safety Instructions Operating Instructions t S 5 S p S Troubleshooting Tips rvice Customer Se General Electric parts catalog 76 PART NO WS02X1 0001 WS28X10010 WS22X10008 WS22X10007 WS02X10003 WS22X10002 WSI9XI0011 WS03X10001 WS30X10002 WS22X10003 WS07X10008 WS02X10004 WS03X10003 WS03X10002 WS15X10008 WS15X10022 FXUTB FXUSB WX5X140 49 50006 PART DESCRIPTION SCREW 10 14 X 3 4 MOUNTING BRACKET NUT 3 8 TUBE INSERT 3 8 TUBE SCREW 10 14 X 1 4 ELBOW 3 8 NPT X 5 8 HEAD O RING 3 3 8 X 3 5 8 SUMP NIPPLE 3 8 NPT X 1 1 2 TUBING
17. remely poor water supplies you may notice the return of the unwanted substance in your water before the six months are up In this case the cartridges should be replaced immediately NOTE If the water supply contains high amounts of sediments the carbon filters may plug with them reducing filtered water flow to the system faucet Cartridge replacement is needed to restore flow Filter Cartridge Replacement CAUTION Never remove the sumps when water pressure is in the Water Filtration system Close the water supply saddle valve to the filter See Fig 1 in the Installation Overview section for location of the saddle valve Open the filtered water faucet Remove the sump using the sump wrench tool provided from the filter head by rota ng the sump as shown in the below illustration Be careful the sump may be full of water Be sure to keep the large o ring seal Cartri 4 artridge 4 1 seal Sump Turn sump wrench tool provided clockwise a 1 1277 TURNSUMP T TO INSTALL a TURN SUMP u p TO REMOVE NET Filter II Filter I Be sure the inside of the sump is clean Thoroughly wash the inside of the sump with hot soapy water and rinse If you are replacing a filter cartridge remove and discard the used filter cartridge Remove the wrapper from the new filter cartridge and insert the filter cartridge in the sump Some cartridges fit either way while others f
18. service at all If you do need service you can relax knowing help is only a phone call away A list of toll free customer service numbers is included in the back section IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING WA R N N G For your safety the information in this manual must be followed to minimize the risk of property damage or personal injury SAFETY PRECAUTIONS a lt Check with your local public works department A WARNING bo not use with water that is L d piu mbing e xou must follow these microbiologically unsafe or of unknown quality guidelines as you install the Water Filtration without adequate disinfection before or after system the system Systems certified for cyst reduction Use the Water Filtration system on a potable may be used on disinfected water that may contain safe to drink home COLD water supply only filterable cysts The filter cartridges will not purify the water or make it safe to drink Do not use on a hot water supply 100 F max PROPER INSTALLATION This Water Filtration system must be properly installed and located in accordance with the Installation Instructions before it is used Install or store where it will not be exposed to Your Water Filtration system will withstand up to temperatures below freezing or exposed to any 125 pounds per square inch psi water pressure type of weather Water freezing i
19. t filter cartridge e Reduces dirt rust and sediment Filter II FXUTB a taste and odor filter cartridge e 6000 gallons e Reduces unpleasant tastes and odors e Reduces 99 596 chlorine e micron carbon block Minimum Maximum Supply Water Pressure 40 125 pounds per square inch psi Minimum Maximum Supply Water Temperature 40 100 Inlet Outlet 3 8 NPT fittings and tubing included Maximum Filtered Water Flow 0 6 gom About the water filtration system Filtered water faucet L1 T L The countertop faucet dispenses filtered 0 drinking water when opened It has a hand Open open Y operated spring loaded closed lever to 22 77 prevent waste You can keep the faucet open by pushing upward on the lever to lock it against the faucet spout Filter Cartridge Life Several variables determine how long the cartridges will last in your Water Filtration system These include How much water you use How much sediment taste and or odor lead or other unwanted substance 15 in the Water No matter which Water Filtration system you have you should replace the cartridges every six months one of the filter sumps between the ribs Mark the date for filter replacement six months from the installation date Filter Replacement Reminder Label Apply the Filter Replacement Reminder Label to Using the Water Filtration System and About the Filter Cartridge In ext
20. ter faucet for ten minutes to flush the system 5 suoianijsu Ajajes e Q A o 2 m gt a 2 S o 5411 Burjoousajqnoj 2 About the water filtration system Flush Procedure Whenever water of unknown quality is passed through the Water Filtration system filter elements should be discarded and the filtration system flushed Circumstances that may require flushing the system are Doil water advisory Safety Instructions Flooding of the Water Filtration system Long term non use The procedure for flushing the Water Filtration system Is See Filter Cartridge Replacementsection and follow steps 1 through 4 Next reinstall the sumps without the filter elements turn water on and flush water through the faucet for one minute Then turn water off remove sumps empty water out of sumps and install new filter elements Follow steps 6 through 9 in the Filter Cartridge Replacement section to complete t S S 5 c S 5 3 S S 5 p 5 Troubleshooting Tips rvice Customer Se Installation Instructions Important Installation Recommendations Read entire manual Failure to follow all guides and rules could cause personal injury or property damage Check with your local public works department for plumbing codes You must follow their gui
21. y Use to connect tubing Customer Se Faucet Installation Be sure there is room underneath the sink to Insert washer into tubing adapter Securely make the needed connections Select one of the tighten to faucet stud followi 1 to install the f t ecu Feed the length of 3 8 OD tube from the bottom up through the mounting hole IN an existing sink spray attachment or soap suoianijsu Ajajes dispenser hole Connect to the tubing adapter as shown in IN a hole to be drilled in the sink top Fig tightening the compression nut securely IN a hole to be drilled in the countertop next n to hese 5 Remove the short shipping tube and insert the spout into the faucet body Rotate spout NOTE Looking at Fig be sure the faucet base into place will fit flat against the surface at the selected location so the gasket will seal A Lower the faucet assembly into place Place If drilling is needed make a 1 1 1 4 dia 4 o oars 2 washer hole Be sure to use the proper procedure for illi place securely tighten the hex nut drilling porcelain or stainless steel Special drill bits may be needed O e Compression nut 2 2 small gasket base and large gasket in that order on to the faucet stem Next place lock washer and hex nut onto faucet stud Fig 3A Fig 3B e S a S gt 2 D
Download Pdf Manuals
Related Search