GE 00019279 Cordless Telephone User Manual
Contents
1. 2 Press the menu mute button to cancel and return to your phone conversation Receiver Volume Control When the handset is ON in talk mode you may adjust the receiver volume by pressing the cid vol or button There are four volume levels to choose from When the maximum or minimum volume level is reached the phone beeps twice VOL 1 is minimum and VOL 4 is maximum nte rcom O pe ration applicable only with additional handsets The intercom feature allows you to have a conversation with another registered handset without tying up the telephone line allowing you to still receive incoming calls Making an Intercom Call 1 Make sure the handset is OFF not in talk mode 2 Press the delete int button on the handset 3 Use the touch tone pad to select the handset you want to page NOTE To cancel page press the delete int button again or the flash exit button on the sending handset 4 Wait for the person at the receiving handset to press the delete int button NOTE If the receiving handset does not answer within two minutes the intercom call is automatically canceled The originating handset displays NO ANSWER 5 When finished press the flash exit button or delete int button on either handset to deactivate the intercom NOTE The system is expandable up to 4 handsets by purchase of optional Model 21920 handset with recharge cradle When 4 handsets are registered the system can handle 2 separate intercom operations2. 6 Press the touch tone pad to select 1YES or 2NO or use the cid vol or a button to scroll to 1YES or 2NO 7 If you select YES press the menu mute button to confirm DE REGISTER shows in the display You will hear a confirmation tone Then HANDSET X DEREGISTERED shows in the display to confirm the handset is deregistered NOTE When you complete the de registration process HANDSET NEEDS REGISTRATION shows in the display To use the handset you MUST re register the handset using the Registration process Global De registration If one or more handsets becomes lost you should de register all handsets to ensure proper system operation Follow the steps below to de register all handsets at the same time WARNING It is not recommended that a handset be de registered unless absolutely necessary because once a handset is de registered that handset s telephone features cannot be used until the handset is re registered 1 Press and hold the page button on the base until the CHARGE IN USE indicator on the base flashes 2 Press and hold the page button on the base again until the CHARGE IN USE indicator on the base flashes rapidly 3 Press and release the page button on the base once 4 All handsets are de registered and HANDSET NEEDS REGISTRATION shows in the display Default Setting As you become familiar with this system you may prefer to use the system s original settings Follow the steps below to return to the factor
3. Hearing Aid Compatibility HAC This telephone system meets FCC standards for Hearing Aid Compatibility Licensing Licensed under US Patent 6 427 009 FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body This transmitter must not be co located or operated in conjunction with any other antenna or transmitter Introduction CAUTION When using telephone equipment there are basic safety A instructions that should always be followed Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference IMPORTANT Because cordless phones operate on electricity you should have at least one phone in your home that isn t cordless in case the power in your home goes out Before You Begin Parts Checklist for model 21905xx 1 Make sure your package includes the items shown here Telephone line cord Handset C ie A a MY Handset AC power battery pack adaptor Battery compartment cover For Model 21905xx2 there will be ONE additional handset charge cradle battery pack and cover than shown above For Model 21905xx3 there will be TWO additional handsets charge cradles battery packs and covers than shown above
4. Provide you with a new or at our option a refurbished unit The exchange unit is under warranty for the remainder of the original product s warranty period How you get service Properly pack your unit Include any cables etc which were originally provided with he product We recommend using the original carton and packing materials Proof of purchase in the form of a bill of sale or receipted invoice which is evidence hat the product is within the warranty period must be presented to obtain warranty service For rental firms proof of first rental is also required Also print your name and address and a description of the defect Send via standard UPS or its equivalent 0 n Thomson Inc 11721 B Alameda Ave Socorro Texas 79927 e Pay any charges billed to you by the Exchange Center for service not covered by the warranty e Insure your shipment for loss or damage Thomson Inc accepts no liability in case of damage or loss e Anew or refurbished unit will be shipped to you freight prepaid What your warranty does not cover e Customer instruction Your Owner s Manual provides information regarding operating instructions and user controls Any additional information should be obtained from your dealer nstallation and setup service adjustments Batteries Damage from misuse or neglect Products which have been modified or incorporated into other products Products purchased or serviced outside the USA Acts of na
5. not in TALK mode 2 Use the cid vol or button to display the CID record you want to delete 3 Press the delete int button The display shows DELETE CALL ID 4 Press the delete int button to erase the record showing in the display The display shows DELETED NOTE Press the flash exit button to return to the standby mode without deleting any CID records Deleting All CID Records 1 Make sure the phone is OFF not in TALK mode 2 Use the cid vol or button to display any Caller ID record 3 Press and hold the delete int button until DELETE ALL shows in the display 4 Press delete int button to erase all of the current CID records The display shows DELETED followed by NO CALLS NOTE Press the flash exit button to return to the standby mode without deleting any CID records Memory Each handset can store up to fifty 20 digit numbers with up to 15 character names in memory for quick dialing This memory feature is in addition to the CID memory log which stores up to 40 CID records in each handset Storing a Name and Number in Phonebook 1 Make sure the phone is OFF not in talk mode 2 Press the phonebook button to display SELECT MEMORY 01 50 3 Press the desired memory location button 01 through 50 or use the cid vol or a button to scroll to desired the memory location NOTE If the memory location is occupied the memory location number and stored name and telephone number shows in the display If the m
6. 2 Press redial button to display the most recent redial number 3 Use the cid vol or a button to scroll to desired redial number 4 Press phonebook button to display SELECT MEMORY 01 50 5 Use touch tone pad to enter two digit desired memory location 01 through 50 Display will show ENTER NAME 6 Follow step 5 in the Storing a Name and Number in Phonebook section to enter name NOTE If the memory location is occupied REPLACE MEMO is displayed and you must confirm replacement by pressing the phonebook button 7 Press phonebook button to save 8 To enter another name and number in a different memory location return to step 2 and repeat the process NOTE If the redial number has more than 20 digits it cannot be stored in memory Inserting a Pause in the Dialing Sequence of a Stored Number Press the pause ringer button on the handset s touch tone pad to insert a delay in dialing sequence when a pause is needed to wait for a dial tone for example after you dial 9 for an outside line or to wait for a computer access tone Each pause counts as one digit in the dialing sequence Reviewing Records Stored in Phonebook 1 Make sure the phone is OFF not in talk mode 2 Press the phonebook button to display SELECT MEMORY 01 50 3 Press the cid vol or a buttons to scroll the records or use the handset s touch tone pad to enter the memory location number Changing Records Stored in Phonebook Fol
7. 888 8888 7 digit telephone number Seven digits 7 digit telephone number 888 8888 Storing CID Records in Internal Memory You may also store CID information in the phone s internal memory NOTE It is important that you format CID records correctly BEFORE storing in internal memory as you cannot reformat CID records stored in memory 1 Make sure the phone is OFF not in talk mode 2 Use the cid vol or a button to scroll to the desired CID record 3 Press the phonebook button to display SELECT MEMORY 01 50 4 Use the touch tone pad to enter a memory location to store the number in that memory location You will hear a confirmation tone NOTE If the memory location is occupied REPLACE MEMO is displayed and you must confirm replacement by pressing the phonebook button NOTE Press the flash exit button once to keep the previous setting making no changes and return to the menu NOTE If the selected CID record contains any information that is non numeric the unit will not allow this record to transfer to the internal user memory The handset will display UNABLE TO STORE To Replace a Stored CID Record 1 Repeat steps 1 through 3 in Storing CID Records in Internal Memory After you enter the memory location REPLACE MEMO shows in the display 2 Press the phonebook button again and the new CID record replaces the old memory in that location You will hear a confirmation tone Deleting a CID Record 1 Make sure the phone is OFF
8. Connect another phone to the same jack If it doesn t work the problem might be your wiring or local service e The handset may be out of range of the base Move closer to the base e Make sure the battery is properly charged for 16 hours e Make sure the battery pack in the handset is properly installed e The handset should beep when you press the talk end button and the charge indicator on the base should be lit when the handset rests in the cradle If not the battery may need to be charged e Place handset in charge cradle for at least 20 seconds to reset the unit Handset does not ring e Make sure the handset ringer software switch is set to on e The handset may be out of range of the base Move closer to the base e You may have too many extension phones on your line Try unplugging some extensions e Check for a dial tone You experience static noise or fading in and out e The handset may be out of range of the base Move closer to base e Make sure base is not plugged into an electrical outlet with another household appliance If necessary relocate the base e Charge the battery for 16 hours Unit beeps e Clean the charging contacts on the cordless handset and base charge cradle with a soft cloth or an eraser e See solutions for No dial tone on previous page e Replace the battery Memory dialing doesn t work e Did you program the memory location keys correctly e Did you follow pr
9. Enter the security code during the outgoing announcement or after you hear the tone Note The default security code is 123 3 Follow the voice menu to use the answering system s remote functions The remote feature lets you perform the following functions To Press this button Review message 1 Play back messages 2 Stop message playback 2 Erase message 0 during message playback Skip message 3 Turn off on answerer 4 Review voice menu options 7 Memory Full When answering system memory is full the system answers after 10 rings beeps and waits for you to enter the 3 digit security code If you don t enter the security code within 8 seconds the phone hangs up You should erase some messages so the answering system can record new messages NOTE The unit also answers after the 10th ring if it is turned off To access the answering system enter your 3 digit security code Changing the Battery CAUTION To reduce the risk of fire or personal injury use only the Thomson Inc approved model 5 2721 Nickel metal Hydride battery Ni MH which is compatible with this unit 1 Make sure the telephone is OFF not in TALK mode before you replace the battery 2 Remove the battery compartment door 3 Disconnect the cord attached to the battery pack and remove the battery pack from he handset 4 Plug the battery pack cord into the jack inside the compartment 5 Put the battery compartment door back on 6 Place hands
10. NOTE To ensure proper battery installation the connector is keyed and can be inserted only one way BATTERY BLACK WIRE RED WIRE 4 Close the battery compartment by pushing the door up until it snaps into place Base Station 1 Choose an area near an electrical outlet and a telephone wall jack RJ11C and place your cordless telephone on a level surface such as a desktop or tabletop 2 Plug one end of the telephone line cord into the TEL LINE jack on the back of the base and the other end into a modular jack 3 Plug the AC power converter into the electrical outlet and the DC connector into the jack on the back of the base 4 Place the handset in the base cradle The charge in use indicator turns on verifying the battery is charging 5 Allow the phone to charge for 16 hours prior to first use If you don t properly charge the phone battery performance is compromised CAUTION To reduce risk of personal injury fire or damage use only the 5 2760 power adaptor listed in the user s guide This power adaptor is intended to be correctly orientated in a vertical or floor mount position Answering System Setup This section shows you how to set up your answering system to receive incoming calls Before you begin the set up process you must turn on the answering system e Press the ans on off button to turn the answering system on and off The MESSAGES indicato
11. handset and press the talk end button 2 When finished press talk end to hang up NOTE Adjust the handset volume by pressing the cid vol or button during a call Call Timer After you press the talk end button on the handset the built in call timer shows on the display and counts the length of time of the call in minutes and seconds Auto Standby If you place the handset in the cradle while the handset is off the hook during a call the call is automatically disconnected Ringer HI LOW OFF Shortcut There are two ways to set the ringer to HI LOW OFF One is the traditional way as described in Handset Setup Ringer Volume menus The other one is this short cut to ringer menu 1 Make sure the phone is OFF not in talk mode 2 Press the pause ringer button to display SET RINGER 1HI 2LOW 30FF 3 Use the touch tone pad on the handset to select 1 2 or 3 or use the cid vol or a button to scroll to your selection HI is the default setting 4 Press pause ringer button again to save and display the new selection for a few seconds Flash Call Waiting If you subscribe to the combined Call Waiting Caller ID service from your local telephone company you will receive Caller ID information if available on Call Waiting calls During a phone call you will hear a beep to indicate another call is waiting on the line and Caller ID information for the waiting call shows on the handset display e To connect to the waiting
12. ovens or VCR If such interference continues move the cordless telephone farther away from these appliances Certain other communications devices may also use the 2 4 GHz frequency for communication and if not properly set these devices may interfere with each other and or your new telephone If you are concerned with interference please refer to the owner s manual for these devices on how to properly set channels to avoid interference Typical devices that may use the 2 4 GHz frequency for communication include wireless audio video senders wireless computer networks multi handset cordless telephone systems and some long range cordless telephone systems Important Installation Guidelines e Avoid sources of noise and heat such as motors fluorescent lighting microwave ovens heating appliances and direct sunlight e Avoid areas of excessive dust moisture and low temperature e Avoid other cordless telephones or personal computers e Never install telephone wiring during a lightning storm e Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations e Never touch non insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface e Use caution when installing or modifying telephone lines Handset Layout talk end button D ei rA L f 12236 06 29 wiwu 08 SMITH re display cid vol 1 31
13. the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation Privacy of Communications may not be ensured when using this product If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna that is the antenna for radio or television that is receiving the interference e Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna e Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is connected If these measures do not eliminate the interference please consult your dealer or an experienced radio television technician for additional suggestions Also the Federal Communications Commission has prepared a helpful booklet How To Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Please specify stock number 004 000 00345 4 when ordering copies Notice The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment
14. 5 555 4321 button Nj gt cid vol redial format conf g Ro button button sy snake x button review A gt f button u 25 2 skip button tone Aon 5 i 6 meo oh button alga O play s mte T E button menu mute Kone Ooper Hears Bion OOE menu delete flash N flash exit button delete int e delete intercom button Base Layout lay stop butt day check play stop button button min language minute button k r button spea hour button Fa message counter indicator o R T vol Aor Y 490 volume buttons co review button gt lt lt gt gt ame skip button JH annonce D G I T A L delete button page button charge in use indicator memo button announce button ans on off answerer button Installing the Phone Installing the Handset Battery NOTE You must connect the handset battery before use CAUTION To reduce the risk of fire or personal injury use only the Thomson Inc approved model 5 2721 Nickel metal Hydride battery Ni MH which is compatible with this unit 1 Locate battery and battery door which are packaged together inside a plastic bag and are separate from the handset 2 Locate the battery compartment on the back of the handset 3 Plug the battery pack cord into the jack inside the compartment
15. ETE Prompt asking if you want to erase one of the 50 records stored in the phone s memory END OF LIST Indicates that there is no additional information in CID memory ENTER NAME Prompt telling you to enter a name in one of the 50 memory locations ENTER TELNUMBR Prompt telling you to enter a telephone number in one of the 50 memory locations NEW Indicates call or calls which have not been reviewed HANDSET NAME Prompt telling you to enter the user name for the registered handset HANDSET NEEDS Indicates you must register a non registered handset prior REGISTRATION to use INCOMPLETE DATA Caller information is interrupted during transmission or the phone line is excessively noisy Indicates no CID information was received you are not subscribed to CID service or CID service is not working LINE IN USE Displays on handset while the line is in use LONG DISTANCE Indicates CID record is from a long distance call LOW BATTERY Indicates the battery needs to be charged NEW VOICE MAIL Indicates voice mail has not been retrieved from service provider CALL SCREENING Indicates you may use the handset to screen calls before answering the call MSG WAITING OFF Indicates voice mail has been retrieved from service provider NEW CALL XX NO CALLS Indicates there are no CID records in memory XX represents the number of new CID records not reviewed OUT OF RANGE May indicate handset is too far away from the base or that the power h
16. FF is the default setting 4 Press the menu mute button to confirm Ring to Answer This feature lets you select the number of times you want the phone to ring before the answering system answers a call From the Handset Setup Menu 1 Press the cid vol or a button to scroll to the RING TO ANSWER sub menu 2 Press menu mute button to enter the menu RING TO ANSWER 3 4 5 6 TSshows in the display 3 Use the cid vol or a to select from 3 to 6 rings or the Toll Saver TS 4 Press the menu mute button to confirm NOTE If you select TOLL SAVER TS the unit answers after the 3rd ring if there are NEW messages in the answering system OR the unit answers after the 5th ring if there are NO new messages Then when you access the answering system from another remote location you may hang up after 4 rings to save long distance charges Security Code You can access the answering system from a tone dialing telephone in another remote location The security code is required for remote access and it prevents unauthorized access to your answering system From the Handset Setup Menu 1 Press the cid vol or a button to scroll to the SECURITY CODE sub menu 2 Press menu mute button to enter the menu SECURITY CODE 1 2 3 shows in the display 3 Use the touch tone pad to enter your new 3 digit security code 4 Press the menu mute button to confirm Area Code From the Handset Setup Menu 1 Press the cid vol or button to scr
17. For Model 21905xx4 there will be THREE additional handsets charge cradles battery packs and covers than shown above Telephone Jack Requirements To use this phone you need an RJ11C type modular telephone jack which might look like the one pictured here installed in your home If you don t have a modular jack call your local phone company to find out how to get one installed Wall plate Modular telephone line jack A A THE LIGHTNING CAUTION TO REDUCE THE THE EXCLAMATION FLASH AND ARROW J RISK OF ELECTRIC SHOCK DO POINT WITHIN THE WARNING TO HEAD WITHIN THE NOT REMOVE COVER OR TRIANGLE IS A PREVENT FIRE OR TRIANGLE IS A BACK NO USER WARNING SIGN WARNING SIGN SERVICEABLE PARTS INSIDE ELECTRICAL SHOCK ALERTING YOU OF REFER SERVICING TO IMPORTANT HAZARD DO NOT DANGEROUS QUALIFIED SERVICE INSTRUCTIONS VOLTAGE INSIDE PERSONNEL EXPOSE THIS THE PRODUCT THE PRODUCT PRODUCT TO RAIN OR MOISTURE SEE MARKING ON BOTTOM BACK OF PRODUCT Installation Digital Security System Your cordless phone uses a digital security system to protect against false ringing unauthorized access and charges to your phone line INSTALLATION NOTE Some cordless telephones operate at frequencies that may cause or receive interference with nearby TVs microwave ovens and VCRs To minimize or prevent such interference the base of the cordless telephone should not be placed near or on top of a TV microwave
18. Model 21905 Series True Digital User s Guide Your new GE telephone system is EXPANDABLE up to a total of 4 handsets by purchase of optional Model 21920 handset with charge cradle Equipment Approval Information Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68 FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA 1 Notification to the Local Telephone Company On the bottom of this equipment is a label indicating among other information the US number and Ringer Equivalence Number REN for the equipment You must upon request provide this information to your telephone company The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called In most but not all areas the sum of the RENs of all devices connected to one line should not exceed 5 To be certain of the number of devices you may connect to your line as determined by the REN you should contact your local telephone company A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA A compliant telephone cord and modular plug is provided with this product It is designed to be connected to a compatible m
19. N for ring tone to signal an incoming call Ringer Volume From the Handset Setup Menu 1 Press the cid vol or 4 button to scroll to the RINGER VOLUME sub menu 2 Press menu mute button to enter the menu SET RINGER 1HI 2LOW 30FF shows in the display 3 Use the touch tone pad on the handset to select 1 2 or 3 or use the cid vol or button to scroll to your selection HI is the default setting 4 Press the menu mute button to save your selection You will hear a confirmation tone and the new volume setting shows in the display NOTE If you turn the ringer OFF the ringer off icon shows in the display Key Tone From the Handset Setup Menu 1 Press the cid vol or button to scroll to the KEY TONE sub menu 2 Press menu mute button to enter the menu SET KEY TONE 10N 2 OFF shows in the display 3 Use the touch tone pad on the handset to select 1 or 2 or use the cid vol or a button to scroll to your selection 10N is the default setting 4 Press the menu mute button to confirm Message Alert This feature sets your answering system to give an alert tone every 10 seconds when there are new messages From the Handset Setup Menu 1 Press the cid vol or button to scroll to the MESSAGE ALERT sub menu 2 Press menu mute button to enter the menu NEW MSG ALERT 10N 2 OFF shows in the display 3 Use the touch tone pad on the handset to select 1 or 2 or use the cid vol or a button to scroll to your selection 2O
20. NDSET NAME shows in the display 3 Use the touch tone pad to enter a name up to 15 characters More than one letter is stored in each of the number keys For example to enter Bill Smith press the 2 key twice for the letter B Press the 4 key 3 times for the letter Press the 5 key 3 times for the letter L Press the 5 key 3 times or the second letter L and press the 1 key to insert a space between the first and last name Press he 7 key 4 times for the letter S press the 6 key once for the letter M press the 4 key 3 times for he letter press the 8 key for the letter T press the 4 key twice for the letter H NOTE If you make a mistake use the delete int button to backspace and delete one character at a time 4 Press the menu mute button to save your name You will hear a confirmation tone and the handset name shows in the display Ringer Tone You may choose from ten different ringer tones From the Handset Setup Menu 1 Press the cid vol or button to scroll to the RINGER TONE sub menu 2 Press menu mute button to enter the menu SET RINGER TONE 01 shows in the display 01 is default setting 3 Use the cid vol or button to scroll to the desired setting 1 through 10 You will hear a sample of the ringer tone you select 4 Press the menu mute button to save your selection You will hear a confirmation tone and the selected ringer tone shows in the display NOTE You must have the Ringer Volume set to O
21. able When the 41st call is received the oldest Caller ID record 1st call is automatically deleted You may review the stored information at any time Calls received since your last review show as NEW in the display Calls that have not been previously reviewed but were received from the same number more than once show as REPT in the display Reviewing CID Records As calls are received and stored the display is updated to let you know how many calls have been received To scroll CID records 1 Make sure the phone is OFF not in talk mode 2 Press the cid vol button to review the newest CID record 3 Press the cid vol a button to review the oldest CID record first Dialing a CID Number 1 Make sure the phone is OFF not in TALK mode 2 Use the cid vol or a button to display the desired record 3 Press the talk end button The number dials automatically NOTE Depending on a how the incoming caller s phone number is formatted when it is received and b whether or not you previously pre programmed your local area code into the set up menu you may need to adjust the format of the incoming caller s stored phone number before making the call press the redial format conf button to adjust the number and try again Available formats include Number of digits Explanation Example Eleven digits long distance code 1 1 317 888 8888 3 digit area code 7 digit telephone number Ten digits 3 digit area code 317
22. as been interrupted Move closer and check connections PAGING or Someone pressed the page button on the base or delete int PAGING FROM button on the handset REPT Indicates a repeat call message Indicates a new call from the same number was received more than once SEARCHING Indicates handset is searching for the base UNKNOWN CALLER Indicates incoming call is from an area not serviced by CID or NAME NUMBER the CID information was not sent Answering System Display Messages The following messages show the status of the answering system or help you set up and use the system 0 59 Indicates the total number of messages CL blinking The voice time day stamp needs to be set Answering system is turned off An blinking F blinking Six bars blinking LA Line Access The system is answering a call Answering system memory is full The system is recording a memo or an announcement External line remote answering system Handset Sound Signals Signal Meaning A long warbling tone with ringer on Signals an incoming call Two short beeps rings once Error Tone Three short beeps several times Page signal One beep every 7 seconds Troubleshooting Guide Telephone Solutions No dial tone Low battery warning e Check or repeat installation steps Make sure the base power cord is connected to a working electrical outlet Make sure the telephone line cord is connected to the base and the wall jack e
23. asts so the above limitations or exclusions may not apply to you e This warranty gives you specific legal rights and you also may have other rights that vary from state to state If you purchased your product outside the USA e This warranty does not apply Contact your dealer for warranty information Accessory Information DESCRIPTION MODEL NO Handset Replacement Batter 5 2721 5 2760 5 2773 To place order have your Visa MasterCard or Discover Card ready and call toll free 1 800 338 0376 A shipping and handling fee will be charged upon ordering We are required by law to collect appropriate sales tax for each individual state country and locality to which the merchandise is being sent Items are subject to availability Prices are subject to change without notice AC Power converter Handset charge cradle
24. at once for example 1st handset intercoms with 2nd handset while 3rd handset intercoms with 4th handset Receiving an Intercom Call When you receive an intercom call your handset beeps To answer the call press the delete int button or talk end button Advanced Intercom Features Receiving an Incoming Call During an Intercom Call If you receive a telephone call during an intercom call the intercom call is immediately terminated and both handsets ring Either handset user may press the talk end button to answer the call Using Intercom with External Telephone Calls During a telephone call you may use the intercom paging function to page another handset and have an off line private two way intercom conversation You may also have a three way conversation between the external caller and the handsets or you may transfer the external telephone call to another handset Two Way Calling 1 During an external call press the delete int button and use the touch tone pad to enter the handset number you want to call NOTE The receiving handset presses the delete int button to answer the intercom call Both intercom users may speak privately The external caller will not hear the intercom conversation 2 When finished press the flash exit button or delete int button to end the intercom call return to the talk mode and resume your original telephone conversation Three Way Calling 1 During an external call press the delete in
25. call press the flash exit button on the handset and your original call is put on hold e To switch between the two calls press the flash exit button TIP Do not press the talk end button on the handset to activate a custom calling service such as call waiting or call will disconnect Last Number Redial You may redial a number up to 32 digits long To quickly redial the last number you dialed 1 Press the talk end button 2 Press the redial format conf button OR 3 Press the redial format conf button first then use the cid vol or button to select the desired redial number Press the cid vol to review the oldest call and scroll toward the most recent calls higher numbers Press the cid vol to review the newest call and scroll to older calls lower numbers NOTE You may choose from three last dialed numbers 4 Press the talk end button The number dials automatically If you get a busy signal and want to keep dialing the number press the redial button to quickly redial the number Exit Press the flash exit button to exit a menu function and return to the standby screen Page The page feature helps you locate a misplaced handset To send and receive pages all handsets must be registered If your handset is not registered follow the instructions in the Registration section of this manual Handset to Handset Paging applicable only with additional handsets 1 Make sure the phone is OFF not
26. e display Your handset should be held near the base during registration process 5 Press and hold the page button on the base unit until the charge in use indicator flashes You will hear a confirmation tone and HANDSET X REGISTERED shows in the handset display where X is the handset number You may now rename your handset Refer to Step 3 amp 4 of Handset Name Section NOTE IF you are re registering the handset through the handset menu to rename your handset you must go to the Handset Name Section and start from the beginning step De Registration This feature allows you to remove a registered handset from base During the de registration process keep the handset near the base From the Handset Setup Menu 1 Press the cid vol or button to scroll to the DEREGISTRATION sub menu 2 Press the menu mute button to enter the menu DEREGISTRATION 1YES 2NO shows in the display The default setting is 2NO 3 Use the touch tone pad to select 1 for YES or 2 for NO Or use the cid vol or a button to scroll to 1YES or 2NO WARNING It is not recommended that a handset be de registered unless absolutely necessary because once a handset is de registered that handset s telephone features cannot be used until the handset is re registered 4 Select NO if you do not want to de register 5 If you select 1YES press the menu mute button and MOVE NEAR TO BASE displays for 2 seconds then CONFIRM 1YES 2NO appears in the display
27. emory location is empty EMPTY shows in the display 4 Press the phonebook button The display shows ENTER NAME 5 Use the touch tone pad to enter a name up to 15 characters More than one letter is stored in each of the number keys For example to enter Bill Smith press the 2 key twice for the letter B Press the 4 key 3 times for the letter Press the 5 key 3 times for the letter L Press the 5 key 3 times for the second letter L and press the 1 key to insert a space between the first and last name Press the 7 key 4 times for the letter S press the 6 key once for the letter M press the 4 key 3 times for the letter press the 8 key for the letter T press the 4 key twice for the letter H NOTE If you make a mistake press the delete int button to backspace and erase the wrong character s or number s 6 Press the phonebook button to confirm and save the record The display shows ENTER TEL NUMBR 7 Use the touch tone pad to enter the telephone number up to 20 digits including pauses press pause ringer button and press the phonebook button again to save the record The unit beeps to confirm NOTE The system treats PAUSES as delays or spaces in the dialing sequence 8 To enter another name and number in a different memory location return to step 2 and repeat the process Storing the Last Number Dialed You may transfer all three redial numbers to internal user memory 1 Make sure the phone in OFF not in TALK mode
28. et in the base or handset charge cradle to charge Allow the handset battery to properly charge for 16 hours prior to first use or when you install a new battery pack If you do not properly charge the phone battery performance will be compromised Battery Safety Precautions e Do not burn disassemble mutilate or puncture Like other batteries of this type toxic materials could be released which can cause injury e To reduce the risk of fire or personal injury use only the Nickel metal Hydride battery listed in the User s Guide e Keep batteries out of the reach of children e Remove batteries if storing over 30 days NOTE The RBRC seal on the battery used in your Thomson Inc product indicates that we are participating in a program to collect and recycle the rechargeable battery or batteries For more information go to the RBRC web site at www rbrc org or call 1 800 8 BATTERY or contact a local recycling center Display Messages The following messages shows the status of the phone provides Caller ID information or helps you set up and use your phone BLOCKED NUMBER Indicates the person is calling from a number which is blocked from transmission CHARGING Indicates the handset needs to charge for a period of time before it can resume normal function DELETE ALL Prompt asking if you want to erase all CID records DELETE CALL ID Prompt asking if you want to erase the CID record showing on the display DEL
29. hen you activate the handset or pick up an extension phone TIP Make sure the volume on the base is set loud enough to hear your incoming calls Messages Playback The message counter let you know when you have message s or new message s To play the messages press the play stop button While a message is playing you may do the following e Press the corresponding play stop button to stop the message playback e Press and release the review button to restart the current message e Press and release the review button twice to go to the previous message e Press and release the skip button to go to the next message e Press the delete button to erase the current message Memory Full When the answering system memory is full the system answers after 10 rings You should erase some messages so the answering system may record new messages Erasing Messages You may erase messages in the following three ways To erase a message while it is playing 1 Press and release play stop button 2 Press the review and skip buttons to select and play the message you want to erase 3 Press the delete button the current message is erased and the next message plays To erase all previously played Messages in a mailbox 1 Make sure the phone is OFF not in talk mode 2 Press and hold the delete button until ALL OLD MESSAGES ERASED is announced To erase a message from the handset 1 Press the flash exit button on the handset 2 Pres
30. in talk mode 2 Press and release the delete int button on a handset PAGING EXTENSION shows in the display 3 Use the touch tone pad to enter the handset number you want to page 4 To cancel the page press the flash exit delete int or talk end button on the originating handset or press the flash exit button on the receiving handset Paging All Handsets from a Handset applicable only with additional handsets 1 Make sure the originating phone is OFF not in talk mode 2 Press and release the delete int button on a handset PAGING EXTENSION shows in the display 3 Use the touch tone pad to enter the handset number you want to page 1 to page Handset 1 2 to page handset 2 etc and 5 to page all handsets 4 To cancel the page press the flash exit delete int or talk end button on the originating handset or press the flash exit button on the receiving handset Paging from the Base Group Page Use the base only to page all registered handsets at the same time 1 Press the page button on the base All handsets beep for two minutes and PAGING FROM BASE shows on each handset s display 2 To cancel the page press the page button on the base or press the talk end button or the flash exit button on each handset Mute To have a private off line conversation use the MUTE feature The party on the telephone line cannot hear you but you can hear them 1 Press the menu mute button The handset display shows MUTE ON
31. low the procedure for Storing Names and Numbers in Phonebook except replace a stored telephone number with a new one Deleting Records Stored in Phonebook 1 Make sure the phone is OFF not in talk mode 2 Press the phonebook button to display SELECT MEMORY 01 50 3 Press the cid vol or button to scroll to the record you want to delete or use the touch tone pad to enter the desired memory location 4 Press the delete int button to mark the record for deletion The display shows DELETE 5 Press the delete int button to delete the record DELETED shows in the display NOTE If you don t want to change or delete a record simply press the flash exit button or wait for one minute to exit the review mode automatically Dialing a Number from Phonebook 1 Make sure the phone is ON in talk mode by pressing the talk end button 2 Press the phonebook button to display MEMO 3 Use the touch tone pad to enter the memory location number The number ials automatically OR 1 Make sure the phone is OFF not in talk mode ress the phonebook button to display SELECT MEMORY 01 50 3 Press the memory location for the phone number you want to dial or use the cid vol or button to scroll to the number you want to dial 4 Press the talk end button The number dials automatically Chain Dialing from Memory Use this feature to make calls from records stored in memory which require a sequence of numbers such as a calli
32. ng card number used for a frequently called long distance number The following example shows how you can store each part of the dialing sequence and use chain dialing to make a call through a long distance service D PS D The Number For Memory Location Long Distance Access Number 7 Authorization Code 8 Frequently called long distance number 9 1 Make sure the phone is ON in talk mode by pressing the talk end button 2 Press the phonebook button and then press 07 3 When you hear the access tone press the phonebook button and then press 08 4 At the next access tone press the phonebook button and then 09 Answering System Operation This section discusses the buttons and features on the answering system Message Counter Indicator The message counter gives you a numeric display of how many messages you have The new message indicator flashes to indicate you have new messages See below for the details a Message counter has a number displayed without flashing No new messages Shows total number of old messages b Message counter has a flashing number displayed There are new messages Shows total number of old and new messages c Message counter has bars Answerer is off d Message counter has an F flashing on the display Memory is full e Message counter has a CL flashing on the display Clock is not set since power up or ter power failure Q f Message cou
33. nter has six horizontal bars flashing on the display MEMO recording Message counter has a An flashing on the display Answering incoming calls and recording an incoming call g h i Message counter has En on the display English is selected as the current voice prompt during language selection Message counter has LA The answering system is being accessed remotely j Message counter has Fr on the display French is selected as the current voice prompt during language selection k Message counter has SP on the display Spanish is selected as the current voice prompt during language selection NOTE While the messages are playing the message counter will display the messages in the order they were received NOTE The maximum recording time for each message is 3 minutes and the total recording time of this unit is 12 minutes Leaving a Message Memo Use the memo feature to leave a message 1 Press and hold the memo button 2 Begin speaking after you hear RECORD MESSAGE and start tone 3 Release the memo button when you are finished recording the memo NOTE Maximum recording time for memo is 3 minutes Screening Calls from the Base 1 When the answering system answers the calll listen while the caller leaves a message to determine who is calling 2 To speak to the caller pick up the handset and press the talk end button The answering system automatically stops recording w
34. odular jack that is also compliant See installation instructions for details Notes e This equipment may not be used on coin service provided by the telephone company e Party lines are subject to state tariffs and therefore you may not be able to use your own telephone equipment if you are on a party line Check with your local telephone company e Notice must be given to the telephone company upon permanent disconnection of your telephone from your line e If your home has specially wired alarm equipment connected to the telephone line ensure the installation of this product does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qualified installer US Number is located on the cabinet bottom REN Number is located on the cabinet bottom 2 Rights of the Telephone Company Should your equipment cause trouble on y our line which may harm the telephone network the telephone company shall where practicable notify you that temporary discontinuance of service may be required Where prior notice is not practicable and the circumstances warrant such action the telephone company may temporarily discontinue service immediately In case of such temporary discontinuance the telephone company must 1 promptly notify you of such temporary discontinuance 2 afford you the opportunity to correct the situation and 3 inform you of your right to bring a complaint
35. oll to the AREA CODE sub menu 2 Press menu mute button to enter the menu SET AREA CODE shows in the display 3 Use the touch tone pad to enter your 3 digit area code 4 Press the menu mute button to confirm You will hear a confirmation tone and the new area code shows in the display NOTE To restore the default setting to press and release delete int when SET AREA CODE shows in the display Tone Pulse From the Handset Setup Menu 1 Press the cid vol a or button to scroll to the TONE PULSE sub menu 2 Press menu mute button to enter the menu TONE PULSE gt 1TONE 2PULSE shows in the display The default setting is 1 TONE 3 Use the touch tone pad or cid vol or to enter 1 TONE or 2 PULSE 4 Press the menu mute button to confirm You will hear a confirmation tone and your selection shows in the display Registration Your packaged handsets are pre registered and ready to use It is not recommended that a handset be registered again unless absolutely necessary From the Handset Setup Menu 1 Press the cid vol or button to scroll to the REGISTRATION sub menu 2 Press the menu mute button to enter the menu REGISTRATION 1YES 2NO shows in the display The default setting is 2NO 3 Use the touch tone pad to select 1 for YES or 2 for NO Or use the cid vol or a button to scroll to 1YES or 2NO 4 If you select 1YES press the menu mute button HOLD BASE PAGE WAIT FOR BEEP shows in th
36. oper dialing sequence Unit locks up and no communication between the base and cordless handset e Unplug the power adaptor from the electrical outlet and the back of the base Remove the handset battery Wait for 30 seconds and plug the power adaptor back into the base and electrical outlet Reconnect the battery and charge for 16 hours Caller ID Solutions No Display e Charge the battery for 16 hours Or replace the battery e Make sure the unit is connected to a non switched electrical outlet Disconnect the power adaptor from the base and reconnect it Caller ID Error Message e The unit displays this message if it detects anything other than valid Caller ID information during the silent period after the first ring This message indicates the presence of noise on the line No Caller ID e You must be subscribed to the standard Name Number Caller ID service from your local telephone company to receive CID information Battery If you experience any of the following problems even after recharging the battery you may need to replace the battery pack e Short talk time e Poor sound quality e Limited range e Charge indicator fails to turn on Answering System Solutions Can t hear messages beep etc e Adjust speaker volume Time Day setting stuck at 12 a m Mon e Set the time clock Answers on 10th ring e Make sure answering system is turned on e Answering system memory may be full Erase
37. r lights when the answering system is on The indicator blinks when you have new messages NOTE The answering system displays when it is off Setting the Voice Prompt Language The default voice prompt language is English To change the answering system s voice prompt language e Press the language button on front of base to change to the FRENCH voice prompt The unit announces OPTION FRANCAISE and Fr shows in the message counter e Press the language button again to change to the SPANISH voice prompt The unit announces SELECCION ESPANOL and SP shows in the message counter NOTE To change to English press the language button again En shows in the message counter NOTE In remote access mode the system follows the selected language The voice prompt language cannot be switched remotely Voice Time Day Stamp and Real Time Clock 1 Make sure the answering system is ON 2 Press and hold the day check button to set the day of the week 3 Press and hold the hour button to set the hour a m or p m Example 12AM 1AM or 12PM 1PM 4 Press and release the min button to advance the clock in one minute intervals Press and hold to increase by 5 minute increments 5 After the time is set the real time clock will be displayed on the handset within 1 minute NOTE You must set the day manually You may choose to set the time manually as well although the time is automatically transmitted by your local phone company a
38. s part of Caller ID service If you subscribe to Caller ID service the current time is set automatically when you receive your first CID record Speaker Volume Use the cid vol a or buttons to adjust speaker volume on the base to a comfortable level L1 is the minimum speaker volume and L8 is the maximum Voice Instruction If you need additional assistance press the review lt lt button in standby mode and follow the voice instructions Recording the Outgoing Announcement If you choose not to record an outgoing announcement a default announcement plays instead For best results when recording you should be about nine inches from the microphone and eliminate as much background noise as possible Make sure the answering system is ON 2 Press and hold the announce button until the speaker announces RECORD ANNOUNCEMENT AFTER TONE 3 Begin speaking after you hear the beep 4 Release the button when you finish your announcement NOTE To return to the default announcement after you have recorded your own outgoing announcement press the announce button and release it when you hear the beep Or press the delete button while the announcement is reviewing Sample Outgoing Announcement Hi this is use your name here can t answer the phone right now so please leave your name number and a brief message after the tone and I ll get back to you Thanks NOTE The maximum recording time for the outgoing announcemen
39. s the play stop key 2 on the handset 3 Press the erase key 0 on the handset to erase a message during playback NOTE Erased messages cannot be restored Remote Access You may access the answering system with the cordless handset or from any tone dial compatible telephone Cordless Handset Use the corresponding handset keys just like you would use the base buttons see Answering System Setup The button functions are located on the handset above each number key For example to play messages e Press the flash exit button The display shows ANSWERER REMOTE ACCESS e Press the play stop button to play the message e When you are finished listening to your messages press the flash exit button again Screening Calls from the Handset Use the handset to screen calls even when you can t hear the answering system When the answering system picks up 1 Press the flash exit button to access the answering system CALL SCREENING shows on the display 2 Listen as the caller leaves a message 3 Press the talk end buttons to speak to the person or press the flash exit button to stop screening the call Accessing the Answering System from Another Location You can access your answering system from any touch tone phone by entering your 3 digit security code during the playing of outgoing announcement or after you hear the outgoing announcement 1 Dial the telephone number to which the answering system is connected 2
40. some messages Incoming messages are incomplete e An extension phone may have been lifted as a message is received e Answering system memory is full Erase some messages e You may have accidently pressed the play stop button during playback and stopped the message Won t respond to remote commands e You must use a tone dial phone This phone does not support pulse rotary dialing e Make sure to enter the correct security code e Did unit hang up If you take no action for a period of time it automatically hangs up Causes of Poor Reception e Aluminum siding e Foil backing on insulation e Heating ducts and other metal construction that can shield radio signals e You re too close to appliances such as microwaves stoves computers etc e Atmospheric conditions such as strong storms e Base is installed in the basement or lower floor of the house e Base is plugged into AC outlet with other electronic devices e Baby monitor is using the same frequency e Handset battery is low e You re out of range of the base General Product Care To keep your unit working and looking good follow these guidelines e Avoid dropping the handset as well as other rough treatment to the phone e Clean the phone with a soft cloth e Never use strong cleaning agents paint thinner abrasive powder alcohol or other chemical products to clean the unit Doing so will damage the finish e Retain the original packaging in case yo
41. t button LINE ON HOLD EXTENSION shows in the display 2 Use the touch tone pad to select Handset You will hear a paging tone and PAGING shows in the originating handset s display NOTE PAGING FROM shows in the display on the receiving handset and the receiving handset presses the delete int or talk end button to answer the intercom 3 When the receiving handset connects press the redial format conf button on the originating handset to conference with the receiving handset and the external caller CONFERENCE shows in the display on the originating and receiving handsets NOTE A handset can enter conference mode directly by pressing talk end on the second handset during a call Call Transfer During an external call you may transfer the external call to another handset 1 Press the delete int button on the originating handset to put an external call on hold and then page the receiving handset 2 Use the touch tone pad on the handset to select Handset You will hear a paging tone PAGING shows on the originating handsets display and PAGING FROM shows on the receiving handset s display 3 When the receiving handset connects press the talk end button on the originating handset to transfer the call Caller ID CID IMPORTANT In order to use this unit s Caller ID features you must subscribe to either the standard Name Number Caller ID Service or Call Waiting Caller ID Service To know who is calling while you are on
42. t is 2 minutes NOTE Press the play stop button at any time to stop playing the announcement Programming the Telephone Standby Screen The handset displays the handset number and user name USER NAME HANDSET X Handset Setup 1 Make sure your phone is OFF not in talk mode 2 Press the menu mute button to go to the main menu HANDSET SETUP shows in the display 3 Press menu mute button to confirm and you may program the following items Set Language Handset Name Ringer Tone Ringer Volume Key Tone Message Alert Ring to Answer Security Code Area Code Tone Pulse Registration Deregistration and Default Setting NOTE During programming you may press the flash exit button at any time to exit the sub menu and return to the menu Language From the Handset Setup Menu 1 Press the cid vol or button to scroll to the SET LANGUAGE sub menu 2 Press menu mute button to enter the menu SET LANGUAGE 1ENG 2FRA 3ESP shows in the display 3 Use the touch tone pad on the handset to select 1ENG 2FRA 3ESP or use the cid vol or button to scroll to the desired language English is the default setting 4 Press the menu mute button to save your selection You will hear a confirmation tone and the selected language shows in the display Handset Name From the Handset Setup Menu 1 Press the cid vol or button to scroll to the HANDSET NAME sub menu 2 Press menu mute button to enter the menu HA
43. the phone you must subscribe to Call Waiting Caller ID Service This unit receives and displays information transmitted by your local phone company This information can include the phone number date and time or the name phone number date and time Date call received Time call received Number of calls Caller s name 1 315 555 4321 Caller s phone number Call Waiting Caller ID Provided you subscribe to Call Waiting Caller ID service from your phone company if you receive an incoming call and you are using the GE multi handset system a beep indicates the presence of a Call Waiting call on the line The Call Waiting Caller ID information will be displayed and stored in the history of all handsets in the system e When you hear the call waiting beep in the handset receiver press the flash exit button to put the current call on hold and answer the incoming call Press flash exit again to return to the original call Receiving CID Records When you receive a call the Caller ID information is transmitted between the first and second ring The Caller ID information appears on the display while the phone rings giving you a chance to monitor the information and decide whether or not to answer the call Storing CID Records In CID Memory If you are not at home or cannot answer your telephone s Caller ID memory stores the data for the 40 most recent calls you received so you can see who called while you were unavail
44. to the Commission pursuant to procedures set forth in Subpart E of Part 68 FCC Rules and Regulations The telephone company may make changes in its communications facilities equipment operations or procedures where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations If these changes are expected to affect the use or performance of your telephone equipment the telephone company must give you adequate notice in writing to allow you to maintain uninterrupted service Thomson Inc 10330 North Meridian Street ae rs eae Indianapolis IN 46290 07 19 ev tom THOMSON 2007 Thomson Inc Trademark s Registered Marcals Registrada s Printed in China images amp beyond Interference Information This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with
45. ture such as but not limited to lightning damage Product Registration Please complete and mail the Product Registration Card packed with your unit It will make it easier to contact you should it ever be necessary The return of the card is not required for warranty coverage Limitation of Warranty e The warranty stated above is the only warranty applicable to this product All other warranties express or implied including all implied warranties of merchantability or fitness for a particular purpose are hereby disclaimed No verbal or written information given by Thomson Inc its agents or employees shall create a guaranty or in any way increase the scope of this warranty e Repair or replacement as provided under this warranty is the exclusive remedy of the consumer Thomson Inc shall not be liable for incidental or consequential damages resulting from the use of this product or arising out of any breach of any express or implied warranty on this product This disclaimer of warranties and limited warranty are governed by the laws of the state of Indiana Except to the extent prohibited by applicable law any implied warranty of merchantability or fitness for a particular purpose on this product is limited to the applicable warranty period set forth above How state law relates to this warranty e Some states do not allow the exclusion nor limitation of incidental or consequential damages or limitations on how long an implied warranty l
46. u need to ship the phone at a later date e Periodically clean the charge contacts on the handset and base with a clean pencil eraser Service If trouble is experienced with this equipment for repair or warranty information please contact customer service at 1 800 448 0329 If the equipment is causing harm to the telephone network the telephone company may request that you disconnect the equipment until the problem is resolved This product may be serviced only by the manufacturer or its authorized service agents Changes or modifications not expressly approved by Thomson Inc could void the user s authority to operate this product For instructions on how to obtain service refer to the warranty included in this guide or call customer service at 1 800 448 0329 Or refer inquiries to Thomson Inc Manager Consumer Relations P O Box 1976 Indianapolis IN 46206 Attach your sales receipt to the booklet for future reference or jot down the date this product was purchased or received as a gift This information will be valuable if service should be required during the warranty period Purchase date Name of store Limited Warranty What your warranty covers Defects in materials or workmanship For how long after your purchase One year from date of purchase The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm whichever comes first What we will do
47. y default settings From the Handset Setup Menu 1 Press the cid vol or a button to scroll to the DEFAULT SETTING sub menu 2 Press the menu mute button to enter the menu DEFAULT SETTING 1YES 2NO shows in the display The default setting is 2NO 3 Use the touch tone pad to select 1YES or 2NO or use the cid vol or button to move the cursor to 1YES or 2NO NOTE If you choose YES all the settings in the programmable menu are returned to factory default setting 4 Press the menu mute button to save your selection You will hear a confirmation tone Telephone Operation Visual Indicators Charge In use Indicator on Base The charge in use indicator on the base will flash to alert you to an incoming call during paging or if you have a message waiting from your service provider The indicator will remain lit when a handset is in the base charging or when the line is in use Making a Call 1 Press the talk end Dial the desired number OR Dial the number first then press the talk end button OR Press the cid vol or button to select the desired record then press the talk end button 2 When finished press the talk end button to hang up NOTE You may enter up to 32 pre dial digits NOTE If you want to delete the pre dial number you entered press the delete int button until all of the digits are erased Answering Calls 1 When the phone rings press the talk end button on the handset OR Pick up the
Download Pdf Manuals
Related Search