Gateway E-9525R Network Card User Manual
Contents
1. 21 Safety Regulatory and Legal Information 23 Using Your EV730 Monitor The EV730 monitor is a high resolution color monitor with 1280 x 1024 maximum resolution Unlimited colors Excellent contrast and legibility Reduced power usage The microprocessor based on screen display OSD controls let you adjust a variety of image settings p Chapter 1 Using Your EV730 Monitor Setting up the monitor Setting up the monitor consists of two procedures attaching the base and connecting the monitor cables If you are setting up your computer for the first time see the setup poster for more information about connecting additional peripheral devices bi To attach the base 1 Carefully set the monitor on its side with the bottom of the monitor facing you 2 Hold the base so the rounded end is pointing toward the back of the monitor then align the hooks on the bottom of the base with the corresponding slots on the bottom of the monitor Retaining latch 3 Slide the base toward the front of the monitor so all hooks are securely in place The retaining latch clicks into place when the base is attached correctly 4 Carefully set the monitor upright and place it on a sturdy level surface n 2 www gateway com Setting up the monitor gt To connect the power and video cables 1 Position the monitor and your computer so you can easily2. Menu Right Power button arrow LED 6 www gateway com Starting the monitor Caution Do not store tapes or diskettes next to the monitor because the monitor generates a strong magnetic field during startup This field can erase or damage data stored on magnetic tapes or diskettes Turn on your computer After your computer is running the power LED on the monitor should be green If not check the connections For more troubleshooting information see Troubleshooting on page 17 Adjust the controls to get the ideal image size and position for you For more information see Adjusting monitor settings on page 8 n Chapter 1 Using Your EV730 Monitor Adjusting monitor settings This monitor features an on screen display OSD that lets you adjust and save contrast brightness and other settings for the display image Menu Press to view the OSD Press again to exit lt left Press to move between the OSD options After selecting an option use to adjust the setting gt right Press to move between the OSD options After selecting an option use to adjust the setting Select Press to select an OSD option The monitor saves any changes you make to the settings even if you turn off the monitor b To adjust the monitor settings 1 2 3 Press the Menu button The OSD menu opens Use the lt and gt buttons to highlight a menu option Press the Select button to select the highlighted menu
3. Ware Gateway GoBack Gateway Gold Gateway Learning Ware Gateway Magazine Gateway Micro Server Gateway Money Ware Gateway Music Ware Gateway Networking Solutions Gateway Online Network O N solution Gateway Photo Ware Gateway Professional PCs Gateway Profile Gateway Solo green stylized GATEWAY green stylized Gateway logo Gateway Teacher Ware Gateway Video Ware HelpSpot InforManager Just click it Learn Gateway Kids BackPack SERVE TO ORDER Server Watchdog the Spotted G Gateway Logo and the Spotted G Logo SpotShop Spotshop com and Your Ware are trademarks of Gateway Inc Intel Intel Inside logo and Pentium are registered trademarks and MMX is a trademark of Intel Corporation Microsoft MS MS DOS and Windows are trademarks or registered trademarks of Microsoft Corporation All other product names mentioned herein are used for identification purposes only and may be the trademarks or registered trademarks of their respective companies 28
4. for ventilation Do not block or cover these openings Make sure you provide adequate space at least 6 inches 15 cm around the system for ventilation when you set up your work area Never insert objects of any kind into the monitor ventilation openings Some products are equipped with a three wire power cord to make sure that the product is properly grounded when in use The plug on this cord will only fit into a grounding type outlet This is a safety feature If you are unable to insert the plug into an outlet contact an electrician to install the appropriate outlet If you use an extension cord with this system make sure that the total ampere rating on the products plugged into the extension cord does not exceed the extension cord ampere rating If your system is fitted with a TV Tuner cable or satellite receiver card make sure that the antenna or cable system is electrically grounded to provide some protection against voltage surges and buildup of static charges Important safety information Care during use Do not walk on the power cord or allow anything to rest on it Do not spill anything on the system The best way to avoid spills is to avoid eating and drinking near your system Do not expose the monitor to rain or use near water If the monitor does get exposed to moisture unplug it and allow it to dry for 24 hours Call Gateway Technical Support for advice on whether the monitor is safe to turn back on When the monito
5. option then use the lt j and gt buttons to adjust it Press the Select button to return to the Main menu When you have finished making all adjustments press the Menu button to exit the OSD n Adjusting monitor settings OSD options Main menu amp Le a sR geumrmuiuub bmnHsctutnl Option Contrast Increases or decreases display image contrast Brightness Increases or decreases display image brightness Horizontal Position H Position Moves the display image to the left or right side of the screen Horizontal Size H Size Increases or decreases the width of the display image Vertical Position V Position Moves the display image to the top or bottom of the screen Vertical Size V Size Increases or decreases the height of the display image Pincushion Curves the sides of the display image inward or outward Trapezoid Increases or decreases the trapezoid distortion of the display image Pin Balance Curves the display image to the left or right Parallelogram Slants the display image to the left or right Tilt Rotates the display image Horizontal Moire H Moire Blurs the focus slightly to minimize the horizontal line pattern which results from interference Vertical Moire V Moire Blurs the focus slightly to minimize the vertical line pattern which results from interference Color Adjusts color balance Recall Resets the monitor settings to the factory default sett
6. to the back of your computer For more information about connecting the video cable see Setting up the monitor on page 2 m Make sure that the video cable is not damaged m Checkthe video port and the end of the video cable for any pins that might be bent or pushed in Picture is fuzzy Adjust the contrast and brightness controls to improve the display image For more information see Adjusting monitor settings on page 8 Picture bounces jitters or has waves Make sure that m Non shielded speakers are not placed too close to the monitor m The monitor is not positioned too close to another monitor power transformer or adapter electric fan fluorescent light metal shelf or laser printer If none of these suggestions solves the problem try plugging the monitor into another outlet preferably one on a different circuit Picture has shadows or ghosts m Remove any extension cables or switchboxes m Make sure that the video cable is connected securely to the back of your computer For more information about connecting the video cable see Setting up the monitor on page 2 m Make sure that the video cable is not damaged m Checkthe video port and the end of the video cable for any pins that might be bent or pushed in 19 Chapter 1 Using Your EV730 Monitor Color is not uniform Make sure that the monitor warms up for at least 30 minutes before making a final judgment about color uniformity Make sure th
7. 2000 click Start Settings then click Control Panel The Control Panel window opens 2 Click Double click the Display icon The Display Properties dialog box opens 3 Click the Settings tab Display Properties Themes Desktop Screen Saver Appearance Settings Display Gateway EV730 on Intel r 82810E Graphics Controller Screen resolution Color quality High 24 bit v 800 by E00 pixels I o Sms sS O8 Troubleshoot Advanced OK Cancel www gateway com 13 Chapter 1 Using Your EV730 Monitor 4 Drag the Screen resolution or Screen area slider to the size you prefer 5 To save your changes in Windows XP click OK then click Yes OR To save your changes in Windows 2000 click OK then click OK again n Help and For more information about adjusting screen resolution in Support Windows XP click Start then click Help and Support Type the keyword changing screen resolution in the HelpSpot Search box Search then click the arrow 14 Power management Power management ENERGY STAR As an ENERGY STAR Partner Gateway has determined that this product meets the ENERGY STAR guidelines for energy efficiency This monitor complies with the EPA s International ENERGY STAR Program which is a program designed to encourage manufacturers of computer equipment to build circuitry into their products to reduce energy consumption during time of non use Energy declaration When co
8. Click the Settings tab Display Properties Themes Desktop Screen Saver Appearance Settings Display Gateway EV730 on Intel r 82810E Graphics Controller Screen resolution Color quality Less i High 24 bit v 800 by 600 pixels I gm NS ON Troubleshoot Advanced 4 Click the arrow button to open the Color quality or Colors list then click the color depth you want 5 To save your changes in Windows XP click OK then click Yes OR To save your changes in Windows 2000 click OK then click OK again n Help and Support 12 For more information about adjusting display settings in Windows XP click Start then click Help and Support Type the keyword changing display settings in the HelpSpot Search box Search 5 then click the arrow www gateway com Adjusting monitor settings Adjusting the screen resolution You can change the screen resolution to a size you prefer For example you can increase the resolution to fit more icons on your desktop or you can decrease the resolution to make reading and identifying objects on the monitor easier The higher the resolution the smaller individual components of the screen such as icons and menu bars appear D To change the screen resolution 1 In Windows XP click Start then click Control Panel The Control Panel window opens If your Control Panel is in Category View click Appearance and Themes OR In Windows
9. Contents Using Your EV730 Monitor 1 Setting up the monitor 2 Removing the base 5 Starting the monitor 6 Adjusting monitor settings 8 OSD Options us ees eter anne MA totes Edel da tcs VL A iut 9 Software controls 11 Power management 15 ENERGY STAR cu ne aude Vlan Monet tee Hop a ea Pe ered mt t 15 Energy declaration 15 Maintenance 2452 eer REESE ant eds eed ere A Re Ra Eee 16 Troublestootilig aie deck dt pean ead pa PS S ed ee SE een 17 NO ICTUrS ws al laa Dern dan tunes DO denied aps oe ace ote und tt 17 Picture is scrambled 18 Display colors are wrong 19 Pictures T zzy 2828 tee ees x ORE ne ra EU anale s 19 Picture bounces jitters or has waves 19 Picture has shadows or ghosts 19 Color is not uniform 20 Image is not sized or centered correctly 20 Image cannot be adjusted full screen 20 Specifications
10. any type of abrasive pad or glass cleaner You i will permanently scratch the glass panel Troubleshooting Troubleshooting If you have problems with the monitor the information in this troubleshooting section may help you solve them Important Make sure that the monitor has warmed up for about 30 minutes before making any judgments about the picture quality No picture m Make sure that the monitor is turned on m Make sure that the power cord is connected correctly to both the back of the monitor and the wall outlet For more information about connecting the power cord see Setting up the monitor on page 2 m Make sure that the video cable is connected securely to the back of your computer For more information about connecting the video cable see Setting up the monitor on page 2 m If the power LED is orange or blinking orange m Make sure that your computer is turned on m Move the mouse or press any key on the keyboard to bring the monitor out of Active Off mode m Restart your computer with the monitor turned on m Make sure that the video cable is not damaged m Checkthe video port and the end of the video cable for any pins that might be bent or pushed in m Turn off the monitor and unplug the video cable from the back of your computer Turn the monitor back on and wait for ten seconds If the monitor is functioning correctly a self diagnostic screen appears 17 Chapter 1 Using Your EV730 Monitor Pi
11. at m Non shielded speakers are not placed too close to the monitor m The monitor is not positioned too close to another monitor power transformer or adapter electric fan fluorescent light metal shelf or laser printer m You demagnetize the screen using the Degauss feature in the OSD For instructions on how to degauss the monitor see Adjusting monitor settings on page 8 Image is not sized or centered correctly Use the size and position controls to adjust the image For instructions on how to change the monitor settings see Adjusting monitor settings on page 8 Image cannot be adjusted full screen Some video modes used by the monitor produce images that cannot be adjusted all the way out to the bezel edge the edge where the screen glass and monitor casing meet This condition does not indicate that the monitor is defective 20 Specifications Specifications Specifications are subject to change without notice or obligation CRT Maximum resolution Display colors Frequency range Power input Certifications Power management Environment 17 inches diagonal 15 9 inches viewable anti reflective anti glare 90 deflection 0 27 mm dot pitch 1280 x 1024 non interlaced Unlimited Horizontal 30 70 kHz Vertical 50 160 Hz 100 240 V 50 60 Hz 2 0A UL cUL EPA FDA and FCC Class B Meets International ENERGY STAR requirements Active Off mode less than or equal to 8 W Operating temperatur
12. cture is scrambled If the picture is scrambled or does not look right you can reset the monitor to its default video mode and resolution settings P To reset the monitor settings 18 1 2 O1 Restart your computer then press and hold F8 while your computer is starting up Select Safe Mode or Enable VGA Mode then press Enter Your computer restarts In Windows XP click Start then click Control Panel If your Control Panel is in Category View click Appearance and Themes OR In Windows 2000 click Start Settings then click Control Panel Click Double click the Display icon The Display Properties dialog box opens Click the Settings tab Drag the Screen Resolution or Screen area slider to the size you prefer If you are not sure what resolution to use select 800 x 600 To save your changes in Windows XP click OK then click Yes OR To save your changes in Windows 2000 click OK then click OK again If prompted restart your computer The mode you have chosen should allow you to use your computer or select a different resolution or number of colors select the maximum number possible If the settings selected are beyond the monitor s display capabilities the operating system restores the image back to the last saved settings in 15 20 seconds n Troubleshooting Display colors are wrong W Restart your computer with the monitor turned on m Make sure that the video cable is connected securely
13. e 41 to 104 F 5 to 40 C Operating humidity 5 to 90 Many products for Gateway and its subsidiaries are custom engineered by our suppliers to Gateway specifications and may vary with similarly marketed products 21 Chapter 1 Using Your EV730 Monitor 22 www gateway com Safety Regulatory and Legal Information Important safety information Your Gateway system is designed and tested to meet the latest standards for safety of information technology equipment However to ensure safe use of this product it is important that the safety instructions marked on the product and in the documentation are followed Warning Always follow these instructions to help guard against personal injury and damage to your Gateway system 23 Appendix A Safety Regulatory and Legal Information Setting up your system 24 Read and follow all instructions marked on the product and in the documentation before you operate your system Retain all safety and operating instructions for future use Do not use this product near water or a heat source such as a radiator Set up the system on a stable work surface The product should only be operated from the type of power source indicated on the rating label If your product has a voltage selector switch make sure that the switch is in the proper position for your area The voltage selector switch is set at the factory to the correct voltage Openings in the monitor case are provided
14. equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio and television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a different circuit from that to which the receiver is connected a Consult the dealer or an experienced radio TV technician for help Compliance Accessories The accessories associated with this equipment are shielded video cable These accessories are required to be used in order to ensure compliance with FCC rules FCC declaration of conformity 26 Responsible party Gateway Companies Inc 610 Gateway Drive North Sioux City SD 57049 605 232 2000 Fax 605 232 2023 This device complies with Part 15 of the FCC Rules Operation of this device is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Caution Cha
15. get at the back y p y ys panel of each Make sure that all power cables can reach a correctly grounded electrical outlet 2 Connect the video cable to the matching blue video port on the back of your computer 3 Tighten the screws on the video cable connectors to keep them from coming loose Tightening the screws also prevents radio and TV interference www gateway com 3 Chapter 1 Using Your EV730 Monitor 4 Connect the power cord that came with the monitor to the AC power connector at the back of the monitor To maintain FCC standards only use the cord that came with the monitor 5 Plug the other end of the power cord into a correctly grounded electrical outlet 2 4 www gateway com Setting up the monitor Removing the base B To remove the base 1 Turn off your computer then disconnect the monitor s power cable 2 Carefully set the monitor on its side with the bottom of the monitor facing you 3 Rotate the base so you can easily get to the retaining latch on the bottom of the monitor then press in the retaining latch 4 While pressing in the latch slide the base toward the back of the monitor then remove the base n www gateway com 5 Chapter 1 Using Your EV730 Monitor Starting the monitor Pi To start the monitor 1 Press the power button The power LED turns green and the monitor demagnetizes itself for about three seconds Gateway Left Select Power arrow button button
16. ings Chapter 1 Using Your EV730 Monitor 10 e R Main menu Option Language Changes the display language for the OSD control system Degauss Demagnetizes the screen Information Displays the frequency and resolution in which the monitor is currently operating www gateway com Adjusting monitor settings Software controls Adjusting the color depth and screen resolution are two of the most basic monitor settings you may need to change Adjusting the color depth Color depth is the number of colors the video card uses Most images look best displayed with the maximum number of colors available Windows lets you choose from several color depth settings for the monitor We recommend that you use the 32 bit True Color setting or the highest setting available at all times If the color in your images seems false or jumpy especially after you have played a game or run a video intensive program check the color depth setting and return it to 32 bit True Color if necessary gt To change the color depth 1 In Windows XP click Start then click Control Panel The Control Panel window opens If your Control Panel is in Category View click Appearance and Themes OR In Windows 2000 click Start Settings then click Control Panel The Control Panel window opens 2 Click Double click the Display icon The Display Properties dialog box opens 11 Chapter 1 Using Your EV730 Monitor 3
17. nges or modifications not expressly approved by Gateway could void the FCC compliance and negate your authority to operate the product Regulatory compliance statements Canada Industry Canada IC Unintentional emitter per ICES 003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de Classe B prescrites dans le r glement sur le brouillage radio lectrique dict par Industrie Canada EPA ENERGY STAR As an ENERGY STAR Partner Gateway has determined that this product meets the ENERGY STAR guidelines for energy efficiency when used with a D Ad computer equipped with a Display Power Management System California Proposition 65 Warning Warning This product contains chemicals including lead known to the State of California to cause cancer and or birth defects or reproductive harm 27 Appendix A Safety Regulatory and Legal Information Notices Copyright 2003 Gateway Inc All Rights Reserved 14303 Gateway Place Poway CA 92064 USA All Rights Reserved This publication is protected by copyright and all rights are reserved No part of it may be reproduced or transmitted by any means or in any form without prior consent in writing from Gateway The inf
18. nnected to a computer that supports the Display Power Management Signaling DPMS Protocol this monitor can conserve significant energy by reducing power consumption during periods of non use When your computer goes into the energy saving mode the monitor will then enter the Active Off mode different from total shut down In the Active Off mode the power LED will still show orange Use these conventions and the power can be reduced to the following levels State LED color Power consumption On Green 74W Active Off Orange Less than or equal to 8 W To wake the monitor when it is in Active Off mode move your mouse or press any keyboard key Access the power management options in the Control Panel to change the period of time after which the monitor enters these low power states 15 Chapter 1 Using Your EV730 Monitor Maintenance To keep the monitor in optimal working order 16 Do not block the ventilation holes Do not expose the monitor to rain or use near water Keep the monitor away from radiators or heat vents Keep the monitor out of direct sunlight Keep the monitor away from any equipment that generates a magnetic field Use a screen saver to avoid permanent phosphor discoloration For more information about screen savers see the documentation that came with your computer Clean the monitor using a soft cloth lightly moistened with water Wipe the cabinet glass panel and controls Caution Do not use
19. ormation in this manual has been carefully checked and is believed to be accurate However changes are made periodically These changes are incorporated in newer publication editions Gateway may improve and or change products described in this publication at any time Due to continuing system improvements Gateway is not responsible for inaccurate information which may appear in this manual For the latest product updates consult the Gateway Web site at www gateway com In no event will Gateway be liable for direct indirect special exemplary incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages In the interest of continued product development Gateway reserves the right to make improvements in this manual and the products it describes at any time without notices or obligation Trademark Acknowledgments 1 800 GATEWAY ActiveCPR ALR AnyKey black and white spot design CrystalScan Destination DestiVu EZ Pad EZ Point Field Mouse Gateway 2000 Gateway Country gateway net Gateway stylized logo Perfect Scholar Solo TelePath Vivitron stylized G design and You ve got a friend in the business slogan are registered trademarks and black and white spotted box logo GATEWAY Gateway Astro Gateway Work Gateway Connected touch pad Gateway Connected music player Gateway Cyber Ware Gateway Education Ware Gateway Flex Case Gateway Gaming
20. r is turned off a small amount of electrical current still flows through the monitor To avoid electrical shock always unplug all power cables and modem cables from the wall outlets before cleaning the system Unplug the system from the wall outlet and refer servicing to qualified personnel if The power cord or plug is damaged Liquid has been spilled into the system The system does not operate properly when the operating instructions are followed The system was dropped or the cabinet is damaged The system performance changes Warning To prevent electric shock never remove the cover No user serviceable parts inside Refer servicing to qualified service personnel Replacement parts and accessories Use only replacement parts and accessories recommended by Gateway Important Do not use Gateway products in areas classified as hazardous locations Such areas include patient care areas of medical and dental facilities oxygen laden environments or industrial facilities 25 Appendix A Safety Regulatory and Legal Information Regulatory compliance statements United States of America Federal Communications Commission FCC Unintentional emitter per FCC Part 15 This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This
Download Pdf Manuals
Related Search