Garmin 696 GPS Receiver User Manual
Contents
1. 2 afford you the opportunity to correct the situation and 3 inform you of your right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68 FCC Rules and Regulations The telephone company may make changes in its communications facilities equipment operations or procedures where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations If these changes are expected to affect the use or performance of your telephone equipment the telephone company must give you adequate notice in writing to allow you to maintain uninterrupted service Interference Information This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particul2. Handset does not ring e Make sure the ringer button is set ON e Move closer to the base The handset may be out of range e You may have too many extension phones on your line Try unplugging some phones e Check for a dial tone You experience static noise or fading in and out e Change channels e Move closer to base The handset might be out of range e Relocate the base Make sure base is not plugged into an electrical outlet with another household appliance e Charge the battery Unit beeps e Place handset in base for 20 seconds if it still beeps charge battery for 16 hours e Clean the charging contacts on handset and base with a soft cloth e See solutions for No dial tone e Replace the battery Memory Dialing doesn t work e Make sure you programmed the memory location keys correctly e Did you follow proper dialing sequence Phone dials in pulse with tone service e Make sure phone is in tone dialing mode Phone won t dial out with pulse service e Make sure phone is in pulse dialing mode Causes of Poor Reception e Aluminum siding e Foil backing on insulation e Heating ducts and other metal construction that can shield radio signals e You re too close to appliances such as microwaves stoves computers etc e Atmospheric conditions such as strong storms Base is installed in the basement or lower floor of the house Base is plugged into AC outlet with other electronic devices e Baby mo
3. Single beep every 7 seconds Low battery warning Troubleshooting Guide Caller ID Solutions No Display e The battery must be fully charged Try replacing the battery e Make sure that the unit is connected to a non switched electrical outlet Disconnect the unit from the wall and plug it in again e You must be subscribed to Caller ID service from your local telephone company in order to receive Caller ID records Caller ID Error Message e The unit displays this message if it detects anything other than valid Caller ID information during the silent period after the first ring This message indicates either the presence of noise on the line or that an invalid message has been sent from the telephone company Cordless Phone Solutions No dial tone e Check installation Make sure the base power cord is connected to a working electrical outlet Make sure the telephone line cord is connected to the base unit and the wall phone jack Connect another phone to the same modular jack if the second phone doesn t work the problem might be with your wiring or local service The handset may be out of range of the base Move closer to the base Make sure the battery is properly charged for 16 hours Ensure the battery pack is installed correctly Did the handset beep when you pressed the talk button Did the charge in use indicator come on The battery may need to be charged Place the handset in the base for at least 20 seconds
4. Use the touch tone pad on the handset to enter the name up to 15 characters and press the memory button to save More than one letter is stored in each of the number keys For example to enter the name Bill Smith press the 2 key twice for the letter B Press the 4 key 3 times for the letter Press the 5 key 3 times for the letter L Wait for one second Press the 5 key 3 times for the second letter L Press the 1 key to insert a space between the L and the S Press the 7 key 4 times for the letter S press the 6 key once for the letter M press the 4 key 3 times for the letter press the 8 key for the letter T press the 4 key twice for the letter H NOTE If you make a mistake press the chan delete button to backspace and erase the wrong character s or number s Press the mem button to save the name The display shows ENTER TEL NUMBR Use the touch tone pad to enter the telephone number you want to store up to 24 digits NOTE The system treats PAUSES as delays or spaces in the dialing sequence 8 Press mem again to store the number You will hear a confirmation tone Storing the Last Number Dialed 1 Repeat steps 1 through 6 in Storing a Name and Number in Memory 2 Press the redial button 3 Press the mem button to store the number You will hear a confirmation tone To replace an old number with a new redial number 1 Repeat steps 1 through 6 in Storing a Name and Number in Memory 2 Press the redial button
5. button to display the CID record you want to delete 3 Press chan delete The display shows DELETE CALL ID 4 Press chan delete again to erase the record and the next Caller ID record shows in the display You will hear a confirmation tone NOTE Press the tone exit key to return to the standby mode Deleting All CID Records 1 Make sure the phone is OFF not in TALK mode 2 Use the vol cid or button to display any Caller ID record 3 Press and hold the chan delete button until DELETE ALL shows in the display 4 Press chan delete again to erase all records You will hear a confirmation tone The display shows NO CALLS NOTE Press the tone exit key to return to the standby mode Memory The handset can store up to ten 24 digit numbers with up to 15 character names in memory for quick dialing This memory feature is in addition to the CID memory log which stores up to 40 CID records Storing a Name and Number in Memory Make sure the phone is OFF not in TALK mode 2 Press the mem button 3 Press the desired memory location 0 through 9 or use vol cid or to scroll to the desired memory location NOTE If the memory location is occupied the memory location number and stored name and telephone number shows in the display If the memory location is empty EMPTY shows in the display Press the mem button again The display shows ENTER NAME NOTE If you don t want to enter the name skip step 5
6. Consumer Relations P O Box 1976 Indianapolis IN 46206 Attach your sales receipt to the guide for future reference or jot down the date this product was purchased or received as a gift This information will be valuable if service should be required during the warranty period Purchase date Name of store Accessory Information To place order have your Visa MasterCard or Discover Card ready and call toll free 1 800 338 0376 A shipping and handling fee will be charged upon ordering We are required by law to collect appropriate sales tax for each individual state country and locality to which the merchandise is being sent Items are subject to availability Prices are subject to change without notice Limited Warranty What your warranty covers e Defects in materials or workmanship For how long after your purchase e One year from date of purchase The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm whichever comes first What we will do e Provide you with a new or at our option a refurbished unit The exchange unit is under warranty for the remainder of the original product s warranty period How you get service e Properly pack your unit Include any cables etc which were originally provided with the product We recommend using the original carton and packing materials Proof of purchase in the form of a bill of sale or recei
7. Service or Call Waiting Caller ID Service To know who is calling while you are on the phone you must subscribe to Call Waiting Caller ID Service This unit receives and displays information transmitted by your local phone company This information can include the phone number date and time or the name phone number date and time Time Date New or Repeated REPT incoming call ne num iG c 5 10 20 REPT ee us Number phone number Caller ID 31 1 555 1 234 of calls name ERE D PAG Call Waiting Caller ID Provided you subscribe to Call Waiting Caller ID service from your phone company if you receive an incoming call and you are already on the phone a beep indicates the presence of a Call Waiting call on the line e When you hear the call waiting beep in the handset receiver press the flash menu button to put the current call on hold and answer the incoming call Press flash menu again to return to the original call Receiving CID Records When you receive a call the Caller ID information is transmitted between the first and second ring The Caller ID information appears on the display while the phone rings giving you a chance to monitor the information and decide whether or not to answer the call Storing CID Records In CID Memory If you are not at home or cannot answer your telephone s Caller ID memory stores the data for the 40 most recent calls you received so you can see who called while you were unavailable Whe
8. has been blocked from transmission CALL WAITING Indicates a call is waiting on the line DELETE ALL Prompt asking if you want to erase all Caller ID records DELETE CALL ID Prompt asking if you want to erase a Caller ID record DELETED Prompt confirming the Caller ID record is erased EMPTY Indicates a memory location is vacant END OF LIST Indicates that there is no additional information in Caller ID memory ENTER NAME Prompt telling you to enter the name for one of the 10 memory locations ENTER NUMBER Prompt telling you to enter the telephone number for one of the 10 memory locations INCOMPLETE DATA Caller information has been interrupted during transmission or the telephone line is excessively noisy LOW BATTERY Indicates the battery needs to be charged NEW Indicates call or calls have not been reviewed NO CALLS Indicates no calls have been received NO DATA No Caller ID information was received PAGING The PAGE button has been pressed on the base PRESS TALK KEY Indicates the CID number is a Direct Dial Number DDN and cannot be formatted REPT Repeat call message Indicates that a new call from the same number was received more than once UNKNOWN NAME CALLER NUMBER Handset Sound Signals Signal Meaning The incoming call is from an area not serviced by Caller ID or the information was not sent A long warbling tone with ringer on Signals an incoming call Three short beeps several times Page signal
9. pack and remove the battery pack from the handset Insert the new battery pack and connect the cord to the jack inside the battery compartment Snap on the handset back cover and screw the rings back on OV Place handset in the base to charge Allow the handset battery to properly charge for 16 hours prior to first use or when you install a new battery pack If you do not properly charge the phone battery performance will be compromised Battery Safety Precautions e Do not burn disassemble mutilate or puncture Like other batteries of this type toxic materials could be released which can cause injury To reduce the risk of fire or personal injury use only the Nickel metal Hydride battery listed in the User s Guide Keep batteries out of the reach of children Remove batteries if storing over 30 days NOTE The RBRC seal on the battery used in your Thomson Inc product indicates that we are participating in a program to collect and recycle the rechargeable battery or batteries For more information go to the RBRC web site at www rbrc org or call 1 800 8 BATTERY or contact a local recycling center Display Messages The following indicators show the status of a message or of the unit BLOCKED CALL The person is calling from a number that has been blocked from transmission BLOCKED NAME The persons name is blocked from transmission BLOCKED NUMBER The person is calling from a number that
10. service phone users to access touchtone services offered by banks credit card companies etc For example when you call your bank you may need to enter your bank account number Temporarily switching to touchtone mode allows you to send your number 1 Dial the telephone number and wait for the line to connect 2 When your call is answered press the tone exit button on the handset to temporarily change from pulse dialing to tone dialing 3 Follow the automated instructions to get the information you need 4 Hang up the handset and the phone automatically returns to pulse rotary dialing mode Exit Press the tone exit button to cancel any command you initiated Ringer On Off 1 Press ringer button to enter the ringer on off setting menu and current setting will show in display 2 Press ringer button again to select the setting and you will hear the confirmation tone NOTE If you turn the ringer OFF RINGER OFF shows in the display Paging the Handset This feature helps to locate a misplaced handset Press the page button on the base The handset will beep for about two minutes or until you press talk on the handset or press the page button on the base NOTE You can still page the handset if the ringer is turned off If the battery is dead the Paging feature will not work Caller ID CID IMPORTANT In order to use this unit s Caller ID features you must subscribe to either the standard Name Number Caller ID
11. 3 Press the mem button and REPLACE MEMO shows in the display 4 Press the mem button again to replace the old number with the new number You will hear a confirmation tone k ion N O Inserting a Pause in the Dialing Sequence of a Stored Number If a pause is needed to wait for a dial or access tone press the PAUSE button to insert a delay in dialing sequence of a stored number for example after you dial 9 for an outside line or to wait for a computer access tone Pause shows in the display as a P and each pause counts as one digit in the dialing sequence Changing a Stored Number 1 Repeat steps 1 through 7 in Storing a Name and Number in Memory 2 Press the mem button and REPLACE MEMO shows in the display 3 Press the mem button to store the number You will hear a confirmation tone Reviewing and Deleting Stored Numbers 1 To review stored numbers press the mem button and use the vol cid or button to scroll to the memory location or press the corresponding number key for a desired memory location 0 9 2 When the data shows in the display press the chan delete button The display shows DELETE 3 Press chan delete again to delete the data The display shows DELETED Dialing a Stored Number 1 Make sure the phone is ON by pressing the talk button NO Press the mem button Press the memory location 0 9 The number dials automatically OR Make sure the phone is OFF n
12. Model 27901 Series 2 4 GHz Cordless Telephone System User s Guide roval Information Equipment A Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68 FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA 1 Notification to the Local Telephone Company On the bottom of this equipment is a label indicating among other information the US number and Ringer Equivalence Number REN for the equipment You must upon request provide this information to your telephone company The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called In most but not all areas the sum of the RENs of all devices connected to one line should not exceed 5 To be certain of the number of devices you may connect to your line as determined by the REN you should contact your local telephone company A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA A compliant telephone cord and modular plug is provided with this product It is designed to be connected to a compatible modular jack that is also compliant See installation instructions for details Notes e This equipment may not be used o
13. ar installation Privacy of Communications may not be ensured when using this product If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna that is the antenna for radio or television that is receiving the interference e Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna e Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is connected If these measures do not eliminate the interference please consult your dealer or an experienced radio television technician for additional suggestions Also the Federal Communications Commission has prepared a helpful booklet How To Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Please specify stock number 004 000 00345 4 when ordering copies Notice The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Hearing Aid Compatibility HAC This telephone system meets FCC standards for Hearing Aid Compatibility Licensing Licensed u
14. ckage includes the items shown here Telephone Base Handset back cover line cord AC power adaptor Handset battery pack Handset rings Telephone Jack Requirements To use this phone you need an RJ11C type modular telephone jack which might look like the one pictured here installed in your Modular home If you don t have a modular jack call your local phone telephone company to find out how to get one installed line jack Installation Digital Security System Your cordless phone uses a digital security system to protect against false ringing unauthorized access and charges to your phone line INSTALLATION NOTE Some cordless telephones operate at frequencies that may cause or receive interference with nearby TVs microwave ovens and VCRs To minimize or prevent such interference the base of the cordless telephone should not be placed near or on top of a TV microwave ovens or VCR If such interference continues move the cordless telephone farther away from these appliances Certain other communications devices may also use the 2 4 GHz frequency for communication and if not properly set these devices may interfere with each other and or your new telephone If you are concerned with interference please refer to the owner s manual for these devices on how to properly set channels to avoid interference Typical devices that may use the 2 4 GHz frequency for co
15. d the two handset rings which are packaged in the box 2 Locate the battery compartment on the back of the handset 3 Plug the battery pack cord into the jack inside the compartment NOTE To ensure proper battery installation the connector is keyed and can be inserted only one way PRESS DOWN FIRMLY mga 4 Insert the battery pack 5 Snap the back of the handset to the handset and screw the rings onto both ends NOTE The handset back is asymmetrical in structure and can ONLY be installed in one orientation Base Station 1 Choose an area near an electrical outlet and a telephone wall jack RJ11C and place your cordless telephone on a level surface such as a desktop or tabletop or you may mount it on the wall 2 Plug one end of the telephone line cord into the TEL LINE jack on the bottom of the base and the other end into a modular jack 3 Plug the AC power converter into the electrical outlet and the DC connector into the jack on the bottom of the base 4 Set the ringer switch on the handset to ON and place the handset in the cradle on the base 5 The charge in use indicator turns on verifying the battery is charging The unit will take 20 seconds to register and verify its security code 6 Allow the p
16. ephone number Seven digits 7 digit telephone number 888 8888 Storing CID Records in Internal Memory You may also store CID information in the phone s internal memory NOTE It is important that you format CID records correctly BEFORE storing in internal memory as you cannot reformat CID records stored in memory 1 Make sure the phone is OFF not in TALK mode 2 Use the vol cid or button to scroll to the desired CID record 3 Press the mem button 4 Use the touch tone pad to enter a memory location 0 9 to store the number in that memory location You will hear a confirmation tone NOTE If the memory location is occupied REPLACE MEMO is displayed and you must confirm replacement by pressing the mem button NOTE Press the tone exit button once to keep the previous setting making no changes and return to the menu NOTE If the selected CID record contains any information that is non numeric the unit will not allow this record to transfer to the internal user memory The handset will display UNABLE TO STORE To Replace a Stored CID Record 1 Repeat steps 1 through 3 in Storing CID Records in Internal Memory After you enter the memory location REPLACE MEMO shows in the display 2 Press the mem button again and the new CID record replaces the old memory in that location You will hear a confirmation tone Deleting a CID Record 1 Make sure the phone is OFF not in TALK mode 2 Use the vol cid or
17. g a phone call you will hear a beep to indicate another call is waiting on the line and Caller ID information for the waiting call shows on the handset display To connect the waiting call press the flash menu button on the handset and your original call is put on hold You may switch back and forth between the two calls by pressing the flash menu button TIP Do not use the talk button to activate custom calling services such as call waiting or you ll hang up the phone Call Timer After you press the TALK call back button on the handset the built in call timer shows on the display and counts the length of time of the call in minutes and seconds Volume When the phone is ON press the vol cid or on the handset to adjust the volume of the handset s earpiece There are four settings Press the vol cid button to increase the volume and vol cid button to decrease the volume You will see the volume setting on the handset display VOL 4 is the maximum and VOL 1 is the minimum Channel Button While talking on the phone you might need to manually change the channel in order to reduce static caused by appliances such as baby monitors garage door openers microwave ovens or other cordless phones Press and release the chan delete button to move to the next clear channel There are 40 channels available Temporary Tone This feature is useful only if you have pulse rotary service Temporary Tone Dialing enables pulse rotary
18. hone to charge for 16 hours prior to first use If you don t properly charge the phone battery performance is compromised CAUTION Use only the 5 2616 black or 5 2617 gray power A adapter that came with this unit Using other power adapters may damage the unit Date and Real Time Clock Setting 1 Press and hold the Sel button until the hour digits is flashing 2 Press and hold the Adj button to advance hour setting increment 3 When the correct hour is set press the Sel button to confirm and the minute digit will flash 4 Press and hold the Adj button to advance the minute setting increment 5 When the correct minute is set press the Sel button to confirm and the Month characters will flash 5 Press and hold the Adj button to select the month 6 When the correct Month is set press the Sel button to confirm and the date digit will flash 7 Press and hold the Adj button to advance the date setting increment 8 When the correct date is set press the Sel button to confirm and the unit will return to standby display Handset Setup There are five programmable menus available Language Local Area Code Ringer Tone Tone Pulse and Factory Default When you program these settings make sure the phone is OFF not in talk mode Pressing the tone exit button will remove you from the menu selection process without changing the feature you are in Display Language 1 Press the flash menu button until LENG 2FRA 3ESP sho
19. mmunication include wireless audio video senders wireless computer networks multi handset cordless telephone systems and some long range cordless telephone systems Important Installation Guidelines e Avoid sources of noise and heat such as motors fluorescent lighting microwave ovens heating appliances and direct sunlight e Avoid areas of excessive dust moisture and low temperature e Avoid other cordless telephones or personal computers e Never install telephone wiring during a lightning storm e Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations e Never touch non insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface e Use caution when installing or modifying telephone lines Handset Layout display vol cid or button eee ynewenn E j talk button R SMITH redial button ringer on off switch chan delete flash menu button channel delete button mem format button memory button pause button tone exit button Installing the Phone Installing the Handset Battery NOTE You must connect the handset battery before use CAUTION To reduce the risk of fire or personal injury use only the Thomson Inc approved Nickel metal Hydride battery Ni MH model 5 2522 that is compatible with this unit 1 Gather the battery the handset the handset back an
20. n coin service provided by the telephone company e Party lines are subject to state tariffs and therefore you may not be able to use your own telephone equipment if you are on a party line Check with your local telephone company e Notice must be given to the telephone company upon permanent disconnection of your telephone from your line e If your home has specially wired alarm equipment connected to the telephone line ensure the installation of this product does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qualified installer US Number is located on the cabinet bottom REN Number is located on the cabinet bottom r Thomson Inc m gt 10330 North Meridian Street Model 27901 Indianapolis IN 46290 00015465 Rev 0 Dom E THOMSON 2006 Thomson Inc 06 38 Trademark s Registered Printed in China THOMSON ry Marcals Registradals 2 Rights of the Telephone Company Should your equipment cause trouble on your line which may harm the telephone network the telephone company shall where practicable notify you that temporary discontinuance of service may be required Where prior notice is not practicable and the circumstances warrant such action the telephone company may temporarily discontinue service immediately In case of such temporary discontinuance the telephone company must 1 promptly notify you of such temporary discontinuance
21. n the 41st call is received the oldest Caller ID record 1st call is automatically deleted You may review the stored information at any time Calls received since your last review show as NEW in the display Calls that have not been previously reviewed but were received from the same number more than once show as REPT in the display Reviewing CID Records As calls are received and stored the display is updated to let you know how many calls have been received To scroll CID records 1 Make sure the phone is OFF not in TALK mode 2 Press the vol cid button to review the newest CID record 3 Press the vol cid button to review the oldest CID record first Dialing a CID Number 1 Make sure the phone is OFF not in TALK mode 2 Use the vol cid or button to display the desired record 3 Press the talk button The number dials automatically NOTE Depending on a how the incoming caller s phone number is formatted when it is received and b whether or not you previously pre programmed your local area code into the set up menu you may need to adjust the format of the incoming caller s stored phone number before making the call press the FORMAT button to adjust the number and try again Available formats include Number of digits Explanation Example Eleven digits long distance code 1 1 317 888 8888 3 digit area code 7 digit telephone number Ten digits 3 digit area code 317 888 8888 7 digit tel
22. nder US Patent 6 427 009 FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body This transmitter must not be co located or operated in conjunction with any other antenna or transmitter CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN A THE LIGHTNING A CAUTION TO REDUCE THE f THE EXCLAMATION FLASH AND ARROW J RISK OF ELECTRIC SHOCK DO POINT WITHIN THE HEAD WITHIN THE f NOT REMOVE COVER OR WARNING TO TRIANGLE IS A BACK NO USER WARNING SIGN ee WARNING SIGN SERVICEABLE PARTS INSIDE ALERTING YOU OF ELECTRICAL SHOCK J ALERTINGYOUOF REFERSERVICINGTO IMPORTANT HAZARD DO NOT DANGEROUS QUALIFIED SERVICE INSTRUCTIONS EXPOSETHIS VOLTAGE INSIDE PERSONNEL ACCOMPANYING THE PRODUCT PRODUCT TO RAIN OR MOISTURE SEE MARKING ON BOTTOM BACK OF PRODUCT Introduction CAUTION When using telephone equipment there are basic safety instructions that should always be followed Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference IMPORTANT Because cordless phones operate on electricity you should have at least one phone in your home that isn t cordless in case the power in your home goes out Before You Begin Parts Checklist Make sure your pa
23. nitor is using the same frequency e Handset battery is low e You re out of range of the base e Microwave oven is using the same frequency General Product Care To keep your telephone working and looking good follow these guidelines e Avoid putting the phone near heating appliances and devices that generate electrical noise for example motors or fluorescent lamps e DO NOT expose to direct sunlight or moisture Avoid dropping the unit and other rough treatment e Clean with a soft cloth e Never use a strong cleaning agent or abrasive powder because this will damage the finish Retain the original packaging in case you need to ship the phone at a later date Periodically clean the charge contacts on the handset and base with a soft cloth Service If trouble is experienced with this equipment for repair or warranty information please contact customer service at 1 800 448 0329 If the equipment is causing harm to the telephone network the telephone company may request that you disconnect the equipment until the problem is resolved This product may be serviced only by the manufacturer or its authorized service agents Changes or modifications not expressly approved by Thomson Inc could void the user s authority to operate this product For instructions on how to obtain service refer to the warranty included in this guide or call customer service at 1 800 448 0329 Or refer inquiries to Thomson Inc Manager
24. ot in TALK mode Press the mem button WN WN N e E A touch tone pad or the vol cid or button to scroll to the number you want to dial 4 Press the talk button The number dials automatically Chain Dialing from Memory Use this feature to make calls which require a sequence of numbers such as calling card calls to a frequently called long distance number Each part of the sequence is dialed from memory The following example shows you how to use chain dialing to make a call through a long distance service The Number For Memory Location Long distance access number 7 Authorization code 8 Frequently called long distance number 9 1 Make sure the phone is ON in TALK mode 2 Press the mem button and then press 7 3 When you hear the access tone press the mem button and then press 8 4 At the next access tone press the mem button and then 9 TIP Wait for the access tones before pressing the next mem button or your call may not go through Changing the Battery CAUTION To reduce the risk of fire or personal injury use only the Thomson Inc approved Nickel metal Hydride battery Ni MH model 5 2522 that is compatible with this unit Make sure the telephone is OFF not in TALK mode before you replace battery 1 NO Remove the rings from each end of the handset then pop the back of the handset off to allow access to the battery compartment WN Disconnect the cord attached to the battery
25. pted invoice which is evidence that the product is within the warranty period must be presented to obtain warranty service For rental firms proof of first rental is also required Also print your name and address and a description of the defect Send via standard UPS or its equivalent to Thomson Inc 11721 B Alameda Ave Socorro Texas 79927 Pay any charges billed to you by the Exchange Center for service not covered by the warranty Insure your shipment for loss or damage Thomson Inc accepts no liability in case of damage or loss e A new or refurbished unit will be shipped to you freight prepaid What your warranty does not cover e Customer instruction Your Owner s Manual provides information regarding operating instructions and user controls Any additional information should be obtained from your dealer Installation and setup service adjustments Batteries e Damage from misuse or neglect e Products which have been modified or incorporated into other products e Products purchased or serviced outside the USA e Acts of nature such as but not limited to lightning damage Product Registration e Please complete and mail the Product Registration Card packed with your unit It will make it easier to contact you should it ever be necessary The return of the card is not required for warranty coverage Limitation of Warranty e The warranty stated above is the only warranty applicable to this product All othe
26. r warranties express or implied including all implied warranties of merchantability or fitness for a particular purpose are hereby disclaimed No verbal or written information given by Thomson Inc its agents or employees shall create a guaranty or in any way increase the scope of this warranty Repair or replacement as provided under this warranty is the exclusive remedy of the consumer Thomson Inc shall not be liable for incidental or consequential damages resulting from the use of this product or arising out of any breach of any express or implied warranty on this product This disclaimer of warranties and limited warranty are governed by the laws of the state of Indiana Except to the extent prohibited by applicable law any implied warranty of merchantability or fitness for a particular purpose on this product is limited to the applicable warranty period set forth above How state law relates to this warranty e Some states do not allow the exclusion nor limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you e This warranty gives you specific legal rights and you also may have other rights that vary from state to state If you purchased your product outside the USA e This warranty does not apply Contact your dealer for warranty information
27. ting is 1 TONE 3 Press the flash menu button to confirm and to advance to the next menu feature Factory Default This feature allows you to restore the unit s original settings 1 Press the flash menu button until DEFAULT shows in the display 2 Use the vol cid or button to scroll to YES The default setting is NO 3 Press flash menu to confirm You will hear a confirmation tone Cordless Phone Basics Making a Call 1 Press the talk button and dial the desired number OR To perform preview dial dial the number first then press the talk button 2 To hang up press the talk button or place the handset in the cradle Receiving a Call 1 To answer a call press the talk button on the handset before you begin speaking 2 To hang up press the talk button or place the handset in the cradle Redial Press the redial button to quickly dial the last number you called up to 32 digits If you get a busy signal and want to keep dialing the number press redial to dial the number again In Use Indicator When the charge in use indicator on the base is lit the handset is either in use or charging The charge in use indicator on the base flashes when you have voice mail The indicator flashes in cadence when receiving an incoming call Flash If you subscribe to the combined Call Waiting Caller ID service from your local telephone company you will receive Caller ID information if available on Call Waiting calls Durin
28. ws in the display 2 Use the vol cid or button or the handset number pad to select 1 English 2 French or 3 Spanish The default setting is 1ENG 3 Press the flash menu button to confirm and to advance to the next menu feature Local Area Code If you enter your local 3 digit area code in the area code menu your local area code does not display on the Caller ID CID list Instead you only see the local 7 digit number Calls received from outside your local area code will display the full 10 digit number 1 Press the flash menu button until AREA CODE shows in the display The default setting Is 2 Use the handset number pad to enter your 3 digit area code NOTE If you make a mistake press the chan delete button to erase the incorrect area code and repeat step 2 3 Press the flash menu button to confirm and to advance to the next menu feature Ringer Tone 1 Press the flash menu button until RINGER TONE shows in the display 2 Use the vol cid or button or the handset number pad 1 3 to enter your selection from Ringer Tone 1 2 or 3 The default setting is RINGER TONE 1 3 Press the flash menu button to confirm and to advance to the next menu feature Tone Pulse This unit allows user to from tone or pulse dialing 1 Press the flash menu button until 1 TONE 2 PULSE shows in the display 2 Use the vol cid or button or the handset number pad to enter your selection The default set
Download Pdf Manuals
Related Search