Futuretech 250 Scanner User Manual
Contents
1. so that its function is impaired e g due to cracks or deep scratches The objective lens will require weekly cleaning as smoke fluid tends to building up residues reducing the light output very quickly The cooling fans should be cleaned monthly The gobos may be cleaned with a soft brush The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air jet The dichroic colour filters the gobo wheel and the internal lenses should be cleaned monthly To ensure a proper function of the gobo wheel we recommend lubrication in six month intervals The 14 15 51839250X62NXS_V_1_1_E DOC quantity of oil must not be excessive in order to avoid that oil runs out when the gobo wheel rotates There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by authorized dealers Please refer to the instructions under Installing Replacing the lamp Replacing the fuse If the fine wire fuse of the device fuses only replace the fuse by a fuse of same type and rating Before replacing the fuse unplug mains lead Procedure Step 1 Open the fuseholder on the rearpanel with a fitting screwdriver Step 2 Remove the old fuse from the fuseholder Step 3 Install the new fuse in the fuseholder Step 4 Replace the fuseholder in the housing Should you need any spare parts please use genuine parts If the power supply cable of this device becomes damaged i2. If the device shall be lowered from the ceiling or high joists professional trussing systems have to be used The device must never be fixed swinging freely in the room 9 15 51839250X62NXS_V_1_1_E DOC Caution Devices in hanging installations may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do NOT install the device Before rigging make sure that the installation area can hold a minimum point load of 10 times the device s weight DANGER OF FIRE When installing the device make sure there is no highly inflammable material decoration articles etc within a distance of min 0 5 m Mount the device to your trussing system using an appropriate clamp For overhead use always install a safety rope that can hold at least 12 times the weight of the fixture You must only use safety ropes with quick link with screw cap Pull the safety rope through the attachment eyelet and over the trussing system or a safe fixation spot Insert the end in the quick link and tighten the safety screw The maximum drop distance must never exceed 20 cm A safety rope which already hold the strain of a crash or which is defective must not be used again Adjust the desired inclination angle via the mounting bracket and tighten the fixation screws DANGER TO LIFE Before taking into operation for the first time the installation has to be approved by an expert Master Slave operation
3. The maximum ambient temperature t 45 C must never be exceeded Operate the device only after having become familiar with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons Never remove the serial barcode from the device as this would make the guarantee void If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock lamp explosion crash etc DESCRIPTION OF THE DEVICE Features Innovative DJ scanner with rotating gobos 7 different dichroic colour filtres and white Rainbow effect with adjustable speed in both directions Gobo wheel with 7 rotating gobos open and blackout Strobe effect with adjustable speed 1 10 flashes sec via shutter DMX controlled operation or stand alone operation with Master Slave function up to 4 slaves Sound controlled via built in microphone Fuzzy Sound Control program continues automatically during periods without music or bass beat Control Board with 4 digit display e Manual focus For MSD HSD 250 MSD 250 2 or MSD HSD 200 lamp DMX control
4. The master slave operation enables that several devices can be synchronized and controlled by one master device On the rear panel of the DJ SCAN 250 you can find an XLR jack DMX Out and an XLR plug DMX In which can be used for connecting several devices Choose the device which is to control the effects This device then works as master device and controls all other slave devices which are to be connected to the master device via a balanced microphone lead Connect the DMX OUT jack with the DMX IN plug of the next device Control Board UU TD mee 5159 Szen N TENN eweg 52 S S see Ne NIN sere 6395 5 seer N 2 NIN se S455 ser Set the desired Master mode for the master device Set the respective Slave mode for all slave devices Blackout socket If you wish to lock the light output e g via an optional footswitch Blackout mode connect your footswitch via a mono jack plug to the Blackout socket 10 15 51839250X62NXS_V_1_1_E DOC Occupation mono 1 4 jack plug a Q Tip Sleeve In Phase Ground DMX 512 connection connection between fixtures 120 Ohms DMX 512 Controller Projector 3 Projector 2 Projector 1 Starting address 13 Starting address 7 Starting address 1 The wires must not come into contact with each other otherwise the fixtures will not work at
5. e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails When rigging derigging or servicing the device staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time The operator has to make sure that safety relating and machine technical installations are approved by an expert after every four year in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year Procedure The device should be installed outside areas where persons may walk by or be seated IMPORTANT OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property The device has to be installed out of the reach of people
6. Fehler Textmarke nicht definiert Operaci n Master Slave oooooccnnnccccnonoccconononccnnononncnnononnncnnnnnnnnnnnnnnn cnn Fehler Textmarke nicht definiert Casquillo Blackout nn nncnnnnnnns Fehler Textmarke nicht definiert Conexi n al controlador DMX conexi n proyector proyector Fehler Textmarke nicht definiert Alimentaci n ee Fehler Textmarke nicht definiert OPERACI N eebe FEHLER TEXTMARKE NICHT DEFINIERT Operaci n Stand Alone oooooococococccocococonononcnnccnncnnnnnnnnnonncnnnnnnnannn nn nncnnnnnn Fehler Textmarke nicht definiert Control por DMX cococococccccccococononcnncnnccnnnnnnnnonccnnnnnnnnnnn nn nn cnnnnnnnnnnnnnnnnnnnnnn Fehler Textmarke nicht definiert Direccionamiento del proyector oococcococccccconocccccnnoncccnnnoncnccnn nc nono nannccnnnns Fehler Textmarke nicht definiert Prot colo RE Fehler Textmarke nicht definiert LIMPIEZA Y MANTENIMIENTO cocccccccncconconcccccncnnnnnnnnnanncnnnnnnnns FEHLER TEXTMARKE NICHT DEFINIERT Reemplazar el fusible nn cnnnnnnnannnnnns Fehler Textmarke nicht definiert ESPECIFICACIONES T CNICAS EEN FEHLER TEXTMARKE NICHT DEFINIERT Das neueste Update dieser Bedienungsanleitung finden Sie im Internet unter You can find the latest update of this user manual in the Internet under Vous pouvez trouvez la derni re version de ce mode d emploi dans l Internet sous Vd puede encontrar la versi n m s reciente de este manual en el Internet bajo ww
7. lamp must only be changed when wearing appropriate protective clothing protection glasses protection gloves helmet with sight leather apron CAUTION The lamp has to be replaced when it is damaged or deformed due to the heat The lamp life given by the manufacturer must never be exceeded This is why you need to take notes on the operational time of the lamp and replace the lamp in time Keep exchanged lamp in a protective container and remove accordingly During the operation the lamp reaches temperatures of up to 600 C Before replacing the lamp unplug mains lead and let the lamp cool down approx 10 minutes During the installation do not touch the glass bulbs bare handed Please follow the lamp manufacturer s notes Do not install lamps with a higher wattage Lamps with a higher wattage generate temperatures the device was not designed for Damages caused by non observance are not subject to warranty Procedure Step 1 Unscrew the fixation screws X Y of the lamp system and carefully remove it from the housing Step 2 If replacing the lamp remove the old lamp from the lamp holder Step 3 Insert the lamp into the lamp holder Step 4 Replace the lamp system in the housing and tighten the fixation screws Step 5 Adjust the lamp as described under lamp adjustment A Do not operate this device with opened cover 8 15 51839250X62NXS_V_1_1_E DOC The lampholder is aligned at the factory Due to differences b
8. light source as sensitive persons may suffer an epileptic shock especially meant for epileptics Keep away children and amateurs OPERATING DETERMINATIONS This device is a lighting effect for creating decorative effects This product is only allowed to be operated with an alternating voltage of 230 V 50 Hz and was designed for indoor use only This device is designed for professional use e g on stages in discotheques theatres etc Lighting effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others The symbol d m determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 0 5 meters This device is only allowed for suspended installation via the mounting bracket In order to safeguard sufficient ventilation leave 50 cm of free space around the device Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Always fix the fixture with an appropriate safety rope 5 15 51839250X62NXS_V_1_1_E DOC
9. vvii anaiss dananira a add 12 Stand Alone ee Ir Le DEE 12 DMX controlled operatiON TTT 12 Address 12 DMX Protocole iaa aa 13 GLEANING AND MAINTENANGE iccsccsecccciesesncssceteccssdansncennesscecsdaassnccadeascctbannsdnsaaciexcisdamannaenesnsscetannaantaetena aan 14 Replacing hr CET ED 15 Lelleg TC elei un el TTT 15 2 15 51839250X62NXS_V_1_1_E DOC INTRODUCTION E FEHLER TEXTMARKE NICHT DEFINIERT INSTRUCTIONS DE S CURIT s ssssssssesssssssessseeteneseneneneees FEHLER TEXTMARKE NICHT DEFINIERT EMPLOI SELON LES PRESCRIPTIONS 0 csesseesseeeeeeeeeees FEHLER TEXTMARKE NICHT DEFINIERT DESCRIPTION DE L APPARE IL 2 eeeeceeeeeeeesseeeeeeeeees FEHLER TEXTMARKE NICHT DEFINIERT E a teg ee aeeuegh steen ege Al a Fehler Textmarke nicht definiert Apercue des ng Fehler Textmarke nicht definiert INSTALLATION 5 ciooooiiocci nacicanrrnnccnan sarria rn enanas FEHLER TEXTMARKE NICHT DEFINIERT Installer Remplacer la lampe ooocoooccccccccccnccococcccconccoccnnnnononncnnnnnnnnnnnnnnnno Fehler Textmarke nicht definiert Ajustage dela amp umi tds Fehler Textmarke nicht definiert Montage par dessus de la t ite Fehler Textmarke nicht definiert Op ration Master Slave cccccccceeeceeceeceeeeeeeeececcceceeeeeeeseesnnueaeeeeees Fehler Textmarke nicht definiert Douille TE e Fehler Textmarke nicht definiert Connexions au contr leur DMX 512 raccord projecteur projecteur Fehler T
10. 9 Strobe effect with increasing speed 200 249 Random strobe effect with increasing speed 250 255 No function Shutter open CLEANING AND MAINTENANCE The operator has to make sure that safety relating and machine technical installations are inspected by an expert after every four years in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are inspected by a skilled person once a year The following points have to be considered during the inspection 1 All screws used for installing the devices or parts of the device have to be tighly connected and must not be corroded 2 There must not be any deformations on housings fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts like axles eyes and others must not show any traces of wearing e g material abrading or damages and must not rotate with unbalances 4 The electric power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed DANGER TO LIFE Disconnect from mains before starting maintenance operation We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents CAUTION The lens has to be replaced when it is obviously damaged
11. Futurelight BEDIENUNGSANLEITUNG USER MANUAL MODE D EMPLOI MANUAL DEL USUARIO DJ SCAN 250 DMX Scanner SCAN 250 pue Fur weiteren Gebrauch aufbewahren Copyright Keep this manual for future needs Nachdruck verboten Gardez ce mode d emploi pour des C Reproduction prohibited utilisations ult rieures R production interdit Guarde este manual para posteriores usos Prohibida toda reproducci n MULTI LANGUAGE INSTRUCTIONS Table of contents EINF HRUNG Aase enigni eg gegen dee ege FEHLER TEXTMARKE NICHT DEFINIERT SICHERHEITSHINWEISE ccceseseeeeecceecessseeeeeeseeceeseeneeseees FEHLER TEXTMARKE NICHT DEFINIERT BESTIMMUNGSGEMARE VERWENDUNG NENNEN FEHLER TEXTMARKE NICHT DEFINIERT GER TEBESCHREIBUNG cscescsessessesessesensesessersneesesseesenseeses FEHLER TEXTMARKE NICHT DEFINIERT Frettercher dg Se Fehler Textmarke nicht definiert Ee Le EE Fehler Textmarke nicht definiert INSTALLATION 0 ceceeecesesssseeeeseeeenessseneeseeeseanseneeseeeeeansensees FEHLER TEXTMARKE NICHT DEFINIERT Lampeninstallatton ampenwechsel rene Fehler Textmarke nicht definiert Lam penjuStlonuUnG DEE Fehler Textmarke nicht definiert A eet Fehler Textmarke nicht definiert Master Slave Belleb uiiiaicia obeuweyiaccntvdindsdesedencies Fehler Textmarke nicht definiert BlackouteBuUChASE sita lcd Fehler Textmarke nicht definiert Anschluss an den DMX 512 Controller Verbindung P
12. all or will not work properly Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection DMX output DMX input XLR mounting socket XLR mounting plug 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal If you are using controllers with this occupation you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMX controllers with other XLR outputs you need to use adapter cables Building a serial DMX chain Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one output with the input of the next fixture until all fixtures are connected Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture Connection with the mains Connect the device to the mains with the enclosed power supply cable 11 15 51839250X62NXS_V_1_1_E DOC The occupation of the connection cables is as follows Cable Pin Interational The earth has to be connected If the device will be directly connected with the local power supply network a disconnection switch with a minimum opening of 3 mm at every po
13. etween lamps fine adjustment may improve light performance Strike the lamp open the shutter set the dimmer intensity to 100 and focus the light on a flat surface wall Center the hot spot the brightest part of the beam using the 3 adjustment screws A B C Turn one screw at a time to drag the hot spot diagonally across the projected image If you cannot detect a hot spot adjust the lamp until the light is even To reduce a hot spot pull the lamp in by turning all three screws A B C clockwise turn at a time until the light is evenly distributed If the light is brighter around the edge than it is in the center or if light output is low the lamp is too far back in the reflector Push the lamp out by turning the screws A B C counterclockwise turn at a time the light is bright and evenly distributed Lamp adjustment a CAUTION HOT LAMP Let the lamp cool down for 10 min Change the lamp by loosening screws X and Y Adjust the lamp position by turning screws A B and C Overhead rigging DANGER TO LIFE Please consider the DIN 15560 and the respective national norms during the installation The installation must only be carried out by an authorized dealer The installation of the device has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment
14. extmarke nicht definiert Alimentations retocada its alar sade Fehler Textmarke nicht definiert MANIEMEN T csccitzscathasaxececsczzaazaesspenccsactxncnddaaneatsieinacadaanaeagencersins FEHLER TEXTMARKE NICHT DEFINIERT Op ration Stand Alone mcr nnnnnnnn Fehler Textmarke nicht definiert Controle par RT Fehler Textmarke nicht definiert Godage du projecteul cional Fehler Textmarke nicht definiert Protocole RI Fehler Textmarke nicht definiert NETTOYAGE ET MAINTENANCE o cccccccccconnoncnnnencnnnnananannnnnnnnnnnns FEHLER TEXTMARKE NICHT DEFINIERT Remplacer le Tusible e cocidos ilatina ee Fehler Textmarke nicht definiert CARACT RISTIQUES TECHNIQUES EEN FEHLER TEXTMARKE NICHT DEFINIERT INTRODUCCION ENEE nene rrnoanenennns FEHLER TEXTMARKE NICHT DEFINIERT INSTRUCCIONES DE SEGURIDAD ccoocconionccncccccncnannancnncnnncnonns FEHLER TEXTMARKE NICHT DEFINIERT INSTRUCCIONES DE MANEJO oooococcccconcconconnccncncnnnnananannnnnnnnnnns FEHLER TEXTMARKE NICHT DEFINIERT DESCRIPCI N DEL APARATO s ssssessssssesesrsseressesststeeestens FEHLER TEXTMARKE NICHT DEFINIERT Features at iia e Fehler Textmarke nicht definiert Descripci n de las poartes A Fehler Textmarke nicht definiert INSTALACION cs FEHLER TEXTMARKE NICHT DEFINIERT Instalar Reemplazar la l mpara oooooocnnccinncocococcconcconnnnnoncnnnnnncnnnnnnnnnnnnno Fehler Textmarke nicht definiert Montaje por encima de la cabeza cece eteeeeeeeeeeeeeeteneeeeetnneeeetens
15. l IS Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems 4 15 51839250X62NXS_V_1_1_E DOC If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature This device falls under protection class The power plug must only be plugged into a protection class outlet Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Make sure that the available voltage is not higher than stated on the rear panel Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective Caution During the operation the housing becomes very hot Do not switch the device on and off in short intervals as this would reduce the lamp s life HEALTH HAZARD A Never look directly into the
16. le has to be included in the permanent electrical installation Lighting effects must not be connected to dimming packs OPERATION After you connected the effect to the mains the DJ SCAN 250 starts running During the Reset the motors are trimmed and the device is ready for use afterwards Turn the objective lens for adjusting the focus in order to obtain a sharp projection Stand Alone operation In the Stand Alone mode the DJ SCAN 250 can be used without controller You can do without a controller as the DJ SCAN 250 features a built in microphone which provides automatic sound control Disconnect the DJ SCAN 250 from the controller and select Master Mode Sound control If you have connected a footswitch to the Blackout socket you can lock the light output Blackout mode and turn it on again Master Slave operation Connect the master and slave devices and adjust the settings as desribed above Please note If you wish to change from one operating mode into another you have to unplug the projector from the mains and plug it again DMX controlled operation You can control the projectors individually via your DMX controller Every DMX channel has a different occupation with different features In order to call up the different features you first have to open the shutter control channel 6 DMX value 132 139 or 250 255 or set the dimmer to the desired intensity control channel 6 DMX value 6 128 Addressing The Contr
17. ol Board on the front side of the base allows you to assign the DMX fixture address which is defined as the first channel from which the DJ SCAN 250 will respond to the controller If you set for example the address to channel 7 the DJ SCAN 250 will use the channel 7 to 14 for control Please be sure that you don t have any overlapping channels in order to control each DJ SCAN 250 correctly and independently from any other fixture on the DMX data link If two three or more DJ SCAN 250 are addressed similarly they will work similarly For address setting press the Mode button until the display shows d and set the desired address via the Up Down buttons Controlling After having addressed all DJ SCAN 250 you may now start operating these via your lighting controller 12 15 51839250X62NXS_V_1_1_E DOC Note After switching on the DJ SCAN 250 will automatically detect whether DMX 512 data is received or not If the data is received the control LED flashes If there is no data received at the DMX input the control LED lights up permanently This situation can occur if the 3 PIN XLR plug cable with DMX signal from controller is not connected with the input of the DJ SCAN 250 the controller is switched off or defective if the cable or connector is defective or the signal wires are swap in the input connector Note It s necessary to insert the XLR termination plug with 120 Ohm in the last lighting in the link in orde
18. r to ensure proper transmission on the DMX data link DMX protocol Control channel 1 Horizontal movement Pan Push slider up in order to move the mirror horizontally PAN Gradual mirror adjustment from one end of the slider to the other 0 255 128 center The mirror can be stopped at any position you wish DMX value Feature 0 255 Gradual adjustment of the mirror position from left to right Control channel 2 Vertical movement Tilt Push slider up in order to move the mirror vertically TILT Gradual mirror adjustment from one end of the slider to the other 0 255 128 center The mirror can be stopped at any position you wish DMX value Feature 0 255 Gradual adjustment of the mirror position from down to up Control channel 3 Colour wheel Linear colour change following the movement of the slider In this way you can stop the colour wheel in any position DMX value Feature 90 107 Light blue Cherry red 128 191 Forwards rainbow effect with increasing speed 192 255 Backwards rainbow effect with increasing speed Control channel 4 Rotating gobo wheel DMX value Feature 192 255 13 15 51839250X62NXS_V_1_1_E DOC Control channel 5 Gobo rotation DMX value Feature 16 135 Forwards gobo rotation with decreasing speed 136 255 Backwards gobo rotation with increasing speed Control channel 6 Shutter strobe DMX value Feature Shutter closed 6 128 129 131 Reset after 3 5 seconds 140 19
19. rojektor ProjektorFehler Textmarke nicht definiert Anschluss ans Nett eegene enee ES EE Fehler Textmarke nicht definiert BEDIENUNG ciaci n aasar aaa ai FEHLER TEXTMARKE NICHT DEFINIERT Stand Alone Beie Fehler Textmarke nicht definiert DMX gesteuerter Betrieb Fehler Textmarke nicht definiert Adressierung des Projektors oooooocccnnnncccnnnnocncccnnonccccanannnc canaria nr naar nn Fehler Textmarke nicht definiert DMS Protokoll Fehler Textmarke nicht definiert REINIGUNG UND WARTUNGooooooooccccccccncccccnononcccncnnnannnannnnnnnnnnnos FEHLER TEXTMARKE NICHT DEFINIERT Sicherungswechsel 0 eee ceeece ee eeeeee ee nono co nono rc cn cnn rca cnn rr Fehler Textmarke nicht definiert TECHNISCHE DATEN euer eeegdeEENekE NENNEN ENEE ene FEHLER TEXTMARKE NICHT DEFINIERT INTRODUCTION rarer a re aar aaa a a aaa ra Aa A a aaao aa Ea E EA ar aaa Na Aa E i aa aaae EEEa ea A ENEE 4 SAFETY INSTRUCTIONS coccion rra e daEEeeeeeEEeAEEESSdEAeh AER 4 OPERATING DETERMINATIONS 2222eeN ege eene SCENE EENS NEEN SEENEN CERN 5 DESCRIPTION OF THE DEVICE wiicnicceiitvassannntecendaansnacanacenandennsscunnendcnsdenassunnicaxiesteanceonnncexdcantiassoonnaateskaduessonne 6 A ie E N NEEE AE aE a SAA a EES 6 OVA VW iia T A A E AA dc 7 INSTALLATION WT 8 Installing Replacing the lame EE 8 Lamp le Tu EE 9 Overhead PIG GING DEE 9 EE e EE 10 Ee ee 10 DMX 512 connection connection between fvtures nn rn nonn nn rnnnnannnno 11 Beil e dek Uu Bun E 11 OPERATION
20. t has to be replaced by a special power supply cable available at your dealer Should you have further questions please contact your dealer TECHNICAL SPECIFICATIONS DMX controlchannels 8 15 kg Maximum ambient temperature t Pp y Fitting lamps _________________ Recommended controllers Wizard 1024 DMX Software Interface Please note Every information is subject to change without prior notice 21 03 2003 15 15 51839250X62NXS_V_1_1_E DOC
21. via every standard DMX controller 6 DMX control channels required 6 15 51839250X62NXS_V_1_1_E DOC Overview 1 Mounting bracket 2 Fixation screw 3 Safety eyelet 4 Objective lens Focus 5 Mirror 6 Housing cover 9 Housing screws DMX Out socket DMxX In socket 10 Power supply 11 Fuseholder 12 Blackout socket 13 Control Board 14 Venting slots 15 Control LED 16 Microphone 17 Mode button 18 Down button 19 Up button LIGHTING CONTROL PROTOCOL DMX 512 XLR occu 1 Gro 2 Si 3 Si u nal nal Blackout Type FUTURELIGHT DJ Scan 250 Power supply 230 V AC 50 Hz ower consumption pi Lamp MSD HSD 200 250 250 2 v T 45 C T 60 C CE dosm Y woewouns Futurelight ree 0 0 T ia NIN Nen N3N z zz 2 09 Control Board 515 525 535 545 afety rope through hment eyelet on the Req 12 fold weight Quick link with screw cap 7 15 51839250X62NXS_V_1_1_E DOC INSTALLATION Installing Replacing the lamp DANGER TO LIFE Only install the lamp with the device switched off Unplug from mains before For the installation you need one MSD HSD 200 GY 9 5 MSD HSD 250 GY 9 5 or MSD 250 2 GY 9 5 lamp The
22. w futurelight com 3 15 51839250X62NXS_V_1_1_E DOC English USER MANUAL Futurelight DJ SCAN 250 DMX Scanner CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing For your own safety please read this user manual carefully before you initial start up Every person involved with the installation operation and maintenance of this device has to be qualilfied follow the instructions of this manual consider this manual to be part of the total product keep this manual for the entire service life of the product pass this manual on to every further owner or user of the product include every supplementay update with the original manual INTRODUCTION Thank you for having chosen a FUTURELIGHT DJ SCAN 250 You will see you have acquired a powerful and versatile device Unpack your DJ SCAN 250 Before you initial start up please make sure that there is no damage caused by transportation Should there be any consult your dealer and do not use the device SAFETY INSTRUCTIONS CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manua
Download Pdf Manuals
Related Search