Fujitsu Siemens Computers 4612 FA Computer Monitor User Manual
Contents
1. 2 English 26361 628 2100 1 5 19 Color monitor 4612 FA If you use a different data cable from the one supplied ensure that it is adequately shielded CE conformance and optimum picture quality are guaranteed only if you use the data cable supplied No data transmission cable should be connected or disconnected during a thunderstorm Make sure that no objects e g jewelry chains paper clips etc or liquids get into the inside of the device danger of electric shock short circuit In emergencies e g damaged casing elements or cables penetration of liquids or foreign matter switch off the unit disconnect the power plug and contact your sales outlet or our Help Desk The screen background lighting contains mercury You must observe the applicable handling and disposal safety regulations for fluorescent tubes If the LCD monitor is damaged for example the glass is broken avoid letting any liquids that may escape coming into contact with any part of your body skin mouth nose or foodstuffs Clean parts of the body and clothing that have already come into contact with such liquids with plenty of soap and water Do not breathe in any of the escaping vapors You should contact your doctor if you have breathed in fumes or come into contact with the liquid Only qualified technicians should repair the device Unauthorized opening and incorrect repair may greatly endanger the user electric shock fire risk You may2. Power cable To guarantee safe operation use the cable supplied Use the following guidelines if it is necessary to replace the original cable set female male receptacles of the cord set must meet CEE 22 requirements The cable has to be HAR certified or VDE certified The mark HAR or VDE will appear on the outer sheath or on the insulation of one of the inner conductors e For devices which are mounted a desk or table type SVT or SUT cable sets may be used For devices which sit on the floor only SJT type cable sets may be used The cable set must be selected according to the rated current for your device Power cable for devices distributed in the US and Canada In the United States and Canada the cord set must also be UL listed and CSA labelled The voltage rating should be min 250 volts a c Please consult the following table for the selection criteria for power cables used in the United States and Canada Cable type Size of conductors in cable Maximum current rating of the device 10 Amps 12 Amps 12 Amps For the United Kingdom Should the plug on the flexible cord not be of the type for your socket outlets do not use an adapter but remove the plug from the cord and discard Carefully prepare the end of the supply cord and fit a suitable plug WARNING THIS APPLIANCE MUST BE EARTHED IMPORTANT The wires in this mains lead are coloured in accordance with the following code Green and Yellow
3. 4612 FA w Q LCD Bildschirm Moniteur Monitor Sk rm Beeldscherm BETRIEBSANLEITUNG OPERATING MANUAL FUJITSU COMPUTERS SIEMENS Sie haben technische Fragen oder Probleme Wenden Sie sich bitte an unseren Help Desk siehe Garantiekarte Aktuelle Informationen zu unseren Produkten Tipps Updates usw finden Sie im Internet http www fujitsu siemens com Is there any technical problem or other question you need clarified Please contact our Help Desk see Guarantee Card The latest information on our products tips updates etc can be found on the Internet under http www fujitsu siemens com Dieses Handbuch wurde auf Recycling Papier gedruckt This manual has been printed on recycled paper Ce manuel est imprim sur du papier recycle Este manual ha sido impreso sobre papel reciclado Questo manuale stato stampato su carta da riciclaggio Denna handbok r tryckt pa recyclingpapper Dit handboek werd op recycling papier gedrukt Herausgegeben von Published by Fujitsu Siemens Computers GmbH Bestell Nr Order No 26361 628 2100 15 19 Printed in Japan AG 0500 05 00 26361 628 2100 1 5 19 4612 FA LCD Bildschirm LCD monitor Moniteur LCD Monitor LCD Monitor LCD LCD skarm LCD beeldscherm Betriebsanleitung Operating Manual Ausgabe Mai 2000 May 2000 edition Deutsch English Frangais Espanol Italiano Svenska Nederland
4. Earth Blue Neutral Brown Live 26361 628 2100 1 5 19 English 5 Color monitor 4612 FA As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured Green or Green and Yellow The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black _ The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red Energy Star Guidelines The Fujitsu Siemens LCD color monitor 4612 FA is designed to conserve electricity by dropping to less than 5 W when it goes into standby suspend and OFF mode With this new power management the 4612 FA Groggy qualifies for the U S Environmental Protection Agency s EPA Energy Star Computers award The EPA estimates that computer equipment uses 5 percent of all business electricity and it is growing rapidly If all desktop computers and peripherals enter a low power mode when not in use the overall savings in electricity could amount to 2 billion annually These savings could also prevent the emission of 20 million tons of carbon dioxide into the atmosphere the equivalent of 5 million automobiles As an Energy St
5. data cable for the monitor is correctly attached to the monitor and the monitor port on the computer gt Press any key on the computer keyboard the computer may be in energy saving mode gt Alter the brightness and or contrast until you get a picture Picture disturbances vertical and horizontal lines picture noise gt First adjust the function Image Adjust H tze in the OSD menu to eliminate vertical bars gt Then adjust the function Image Adjust Fine in the OSD menu to eliminate picture noise or horizontal lines or OS 2 with Windows emulation installed is used the monitor can be adjusted with the floppy disk supplied D If one of the operating systems Windows for Workgroups Windows 95 98 Windows NT Permanently unlit or lit pixels Pixel faults in the form of permanently lit or unlit pixels can occur with TFT displays Up to 10 permanently lit and or 10 unlit pixels does not constitute grounds for exchanging the unit Please contact our Help Desk if the number of pixel faults exceeds the above number The screen becomes darker The background lighting has a limited lifetime If your monitor display should become too dark the background lighting will have to be exchanged Please contact our Help Desk Image of last screen display still visible If you switch from a high contrast display for example black lines characters on a white background to a picture of medium brightness you may be able to see a faint image
6. other products will appear in the accompanying documentation NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 ofthe FCC rules and meets all requirements of the Canadian Interference Causing Equipment Regulations These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in strict accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures _ Reorient or relocate the receiving antenna e Increase the separation between equipment and the receiver _ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Fujitsu Siemens Computers GmbH is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than
7. those specified by Fujitsu Siemens Computers GmbH The correction of interferences caused by such unauthorized modification substitution or attachment will be the responsibility of the user The use of shielded I O cables is required when connecting this equipment to any and all optional peripheral or host devices Failure to do so may violate FCC rules Declaration of Conformity This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Product Name LCD Monitor Trade Name Fujitsu Siemens Computers Model Number s 4612 FA Name of Responsible Party Siemens Information and Communication Products LLC 3860 N First Street San Jose CA 95134 1702 U S A Contact Person Mike Fitzner Phone No 408 428 8918 Fax No 408 428 7290 4 English 26361 628 2100 1 5 19 Color monitor 4612 FA We Siemens Information and Communication Products LLC hereby declare that the equipment bearing the trade name and model number specified above was tested confirming to the applicable FCC Rules under the most accurate measurement standards possible and that all the necessary steps have been taken and are in force to assure that production units of the same equipment will continue to comply with the Commissions requirements
8. 2 and secure the plug in connection by tightening the safety screws Data cables with two 15 pin D SUB connectors are available from specialized dealers After you have switched the monitor you must select the desired input using the DVI D SUB button A message to this effect appears on screen gt Connect the connector of the power cable to the power connector 4 of the monitor and ensure a secure connection gt Mount the cover over the connections again 26361 628 2100 1 5 19 English 9 Color monitor 4612 FA Connecting cables to the computer Information on the computer connections and interfaces is contained in the operating manual for your computer If your computer has two monitor ports onboard screen controller and separate graphics card the monitor port for the separate graphics card is usually active gt Connect the data cable to the active monitor port on the computer and secure the plug in connection by tightening the safety screws gt Connect the male receptacle of the power cable supplied to the monitor socket of the computer and ensure a secure connection gt Plug the power connector of the computer into a properly grounded power outlet appropriate graphics drivers for your application software Details of how to do this are D When you start working with your monitor for the first time you should install the provided in the documentation on your screen controller the associated driver
9. Ce T gt Use the Aor Y button to make the desired setting DOWN UP If you highlight the Auto Adjust entry using the SELECT button the picture position is automatically adjusted AUTO ADJUST gt Press the EXIT button to return to the main menu gt Press the EXIT button to exit the OSD menu All changes will be saved immediately after exiting the OSD menu Adjust function as is carried out by the program on the floppy disk provided This basic D A basic monitor setting is required for automatic adjustment of menu items with the Auto setting is also useful for manual adjustment If the program cannot be used on your computer because another operating system is used you must adjust a white screen for the Auto Adjust function Setting brightness and contrast Brightness Contrast Brightness Setting the brightness of the display Setting the contrast of the display Auto Adjust Automatic contrast adjustment Correcting the contrast manually if the video signals of the graphics card do not match the VGA standard D If the contrast is set too high bright surfaces can no longer be distinguished from very bright surfaces If the contrast is set too low the maximum brightness will not be achieved Making automatic picture adjustments Auto Adjust The picture position Position pixels and stability Image Adjust are automatically set when you press first the SELECT and then the A button in the adjustment wi
10. ar Partner Fujitsu Siemens Computers GmbH has determined that this product meets the Energy Star guidelines for energy efficiency CE certificate directives 89 336 EEC Electromagnetic compatibility and 73 23 EEC Low voltage The shipped version of this device complies with the requirements of the EEC directive Disposal and recycling This device has been manufactured to the greatest possible degree from materials which can be recycled or disposed of in a manner that is not environmentally damaging The device is taken back after use to be recycled provided that it is returned in a condition that is the result of normal use Any components not reclaimed will be disposed of in an environmentally acceptable manner If you have any questions on disposal please contact your local office our Help Desk or Fujitsu Siemens Computers GmbH Recyclingcenter D 33106 Paderborn Tel 49 5251 81 80 10 Fax 49 5251 81 80 15 6 English 26361 628 2100 1 5 19 Color monitor 4612 FA Checking the contents of the consignment gt Unpack all the individual parts Check the delivery for damage incurred during transportation gt Check whether the delivery agrees with the details in the delivery note The complete LCD monitor package includes Y monitor two data cables power cable floppy disk warranty this Operating Manual Should you discover that the de
11. ction Changing the monitor settings in chapter Operation of the monitor Target group You don t need to be an expert to perform the operations described here Do however read the chapter Important notes in the Operating Manual of the computer and in this Operating Manual In the event of any problems occurring please contact your sales outlet or our Help Desk Further information Details of how you set the resolution and refresh rate are provided in the documentation on your screen controller the associated driver software 26361 628 2100 1 5 19 English 1 Color monitor 4612 FA Notational conventions The meanings of the symbols and fonts used in this manual are as follows Pay particular attention to texts marked with this symbol Failure to observe this warning endangers your life destroys the system or may lead to loss of data D Supplementary information remarks and tips follow this symbol gt Texts which follow this symbol describe activities that must be performed in the order shown Quotation marks indicate names of chapters and terms that are being emphasized Texts in italics indicate filenames and menu items Important notes In this chapter you will find information regarding safety which is essential to take note of with your monitor Safety This device complies with the relevant safety regulations for data processing equipment including electronic office machines for use in an o
12. efresh rates vertical frequencies from 56 to 85 Hz all absolutely flicker free digital screen controller with microprocessor for storing 26 different display modes e freely adjustable color alignment for matching the screen colors to the colors of various input and output devices convenient operation via integrated OSD On Screen Display menu e VESA DDC compatibility e VESA FPMPMI compatibility Flat Panel Monitor Physical Mounting Interface mechanical interface to swivel arm and wall bracket e plug amp play capability power management for reducing power consumption when the computer system is not in use compliance with the recommendations in accordance with TCO 99 In normal screen mode dark characters against a light background the monitor satisfies the ergonomic requirements for the GS symbol This Operating Manual contains important information you require to start up and run your LCD monitor A graphics card screen controller with VGA interface or a digital graphics card with DVI interface is required to control the 4612 FA LCD monitor The monitor processes the data supplied to it by the screen controller The screen controller the associated driver software is responsible for setting the modes resolution and refresh rate When putting the monitor into operation for the first time the screen display should be optimally adapted to the screen controller used and adjusted in accordance with your needs see se
13. erface between the monitor and the computer If your computer is equipped with a VESA DDC compatible VGA interface it can automatically read the data for ensuring optimum operation from your monitor and select the appropriate settings following monitor instead D If the monitor 4612 FA is not yet displayed in the list of monitors you can select the Siemens MCF 4611 TA Preset operating modes The display position and size have been set to optimum values at the factory for the operating modes listed above Depending on the screen controller used it may be necessary to adjust the display position and size In this case you can change and save the settings see Operation of the monitor The following are the most frequently used of the preset operating modes Horizontal frequency Refresh rate 31 5 kHz 720 x 400 31 5 kHz 640 x 480 37 5 kHz 640 x 480 37 9 kHz 800 x 600 46 9 kHz 800 x 600 48 4 kHz 1024 x 768 60 0 kHz 1024 x 768 64 0 kHz 1280 x 1024 80 0 kHz 1280 x 1024 For ergonomic reasons a screen resolution of 1024 x 1280 pixels is recommended Because of the technology used active matrix an LCD monitor provides a totally flicker free picture even with a refresh rate of 60 Hz 20 English 26361 628 2100 1 5 19 Color monitor 4612 FA Pin assignment D SUB Video input red 5 V DDC Video input green Video input blue Green video ground DDC Clock Blue video ground 26361 628 2100 1 5 19 Eng
14. es at the beginning of this manual CE conformance and optimum picture quality are guaranteed only if you use the data cable supplied Do not cover the ventilation openings of the monitor The computer power plug must be pulled gt sure that the monitor and the computer are switched off 8 English 26361 628 2100 1 5 19 Color monitor 4612 FA Connecting cables to the monitor The monitor ports are protected by a cover 1 Cover lever 3 DVI connector 2 D SUB connector 4 Power connector gt Press the cover lever 1 to the left and remove the cover The data cables provided have a plug for the DVI connection socket on the monitor and a 15 pin D SUB plug or a DVI plug for the connection on the computer gt Select the suitable data cable for your computer Digital graphics card with DVI interface DVI connector Graphics card with VGA interface D SUB connector Information on the computer connections and interfaces is contained in the operating manual for your computer gt Connect the DVI connector of the data cable to the DVI connector the monitor 3 and secure the plug in connection by tightening the safety screws connectors or if you want to connect the monitor to a second computer proceed as il If instead of the data cables supplied you want to use a data cable with two 15 pin D SUB follows gt Connect the D SUB connector of the data cable to the appropriate D SUB connector
15. ff the factory settings The DVI D SUB button allows you to choose between the inputs whether the OSD menu is switched on or off A message to this effect appears on screen operation some functions are not available as they are not required due to the digital D The OSD menu for analog monitor operation is described in the following During digital transmission technology used To make a setting perform the following steps gt Press the button SELECT to activate the OSD menu The main menu appears on the screen with menu options for the setting functions The first option Brightness Contrast is EES highlighted With the W button you can move the marking down and view the menu items on the second page With the A button you can move the marking up gt BRIGEIINESSIESONTHASE gt If necessary use the A or Y button to AUTO ADJUST mark another option e g Position eee gt Press the SELECT button to select the os highlighted option COLOR CONTROL 26361 628 2100 1 5 19 English 13 Color monitor 4612 FA Depending on the menu item in this case Position a setting window is offered with different functions Using the SELECT button you can activate the functions in the setting window one after the other gt Choose the function you require using the BOSIMON SELECT button In addition to the active function the button symbols and are also displayed LEFT
16. ffice environment If you have any questions contact your sales outlet or our Help Desk The display surface of the LCD monitor is sensitive to pressure and scratches You should therefore be careful with the display surface so as to avoid lasting damage Newton rings scratches e ifthe device is brought into the installation site from a cold environment condensation can form Before operating the device wait until it is absolutely dry and has reached approximately the same temperature as the installation site e During installation and before operating the device please observe the instructions on environmental conditions in the chapter entitled Technical data as well as the instructions in the chapter Installing an ergonomic video workstation e To ensure sufficient ventilation the intake and exhaust air openings of the monitor must never be blocked The device automatically sets itself to the correct voltage within the range from 100 V to 240 V Ensure that the local mains voltage lies within these limits _ Ensure that the power socket on the device or the grounded wall outlet is freely accessible The ON OFF switch does not disconnect the device from the line voltage To disconnect the line voltage completely remove the power plug from the socket e Lay all cables so that nobody can stand on them or trip over them When attaching the device observe the relevant notes in the chapter Connecting the monitor
17. hics images Graphic Mode Set mode for the optimum display of graphics and images 26361 628 2100 1 5 19 English 15 Color monitor 4612 FA Switching full screen mode on or off Expansion Mode If your graphic card is only capable of displaying a resolution lower than 1280 x 1024 the scaling process of the monitor can display up to 1280 x 1024 pixels by determining intermediate values with interpolation Full Screen Switch on the full screen mode The display area is stretched to the full picture size 1 280 pixels side ratio 5 4 As a result the display may appear distorted Keep Aspect Switch on the proportional full screen mode The display area is expanded to the maximum picture size while maintaining the side ratio either full picture width or full picture height Expansion Off Switching the full screen mode off At resolutions lower than 1280 x 1024 a display with a black border appears Setting automatic video signal detection video detect With this function the selection of the video input can be controlled with the monitor is connected to two computers Switch off the automatic video signal detection The switch over between the video inputs is not automatic but instead must be carried out manually with the DVI D SUB button First Detect Switch on the First Detect mode As long as a signal is present at the current video input the monitor remains set to this video input regardless of whether or n
18. ied floppy disk into the floppy disk drive gt Open the Readme file on the floppy disk and follow the instructions in the file Your monitor should now already be properly adjusted If none of the above operating systems is used or minor corrections are to be made to the screen display then change the monitor settings with the OSD menu 12 English 26361 628 2100 1 5 19 Color monitor 4612 FA Monitor settings using the OSD menu You can use the buttons on the control panel to set the screen display via an integrated OSD menu On Screen Display The OSD menu is available in different languages The English menu names are used in the following description default setting The language can be set in the OSD menu Language Select OSD CC EXIT v CONTROL 4 SELECT RESET DVI D SUB The SELECT button switches the OSD menu on selects the highlighted option or activates a function in the setting window For menu items with the Auto Adjust function automatic adjustment will be started Use the CONTROL A or Y buttons to highlight a menu option or a submenu and define the settings for the function you have selected The EXIT button deactivates the OSD menu or returns you from a submenu to the main menu The OSD menu is automatically closed if no button is pressed for several seconds The time period can be set in the OSD menu OSD Turn Off Time The RESET button activates with the OSD menu switched o
19. ion programs take note of the information below The primary colors blue and red on a dark background do not produce the minimum required contrast of 3 1 and are therefore not suitable for continuous text and data entry When using several colors for characters and background and giving the primary colors full modulation you can obtain very suitable color combinations see the following table Tome Tome se Tom one rem sami me _ CSR _ oe _ en _ w _ REN EE Color combination very suitable Color combination not suitable because color locations are too close together thin characters are not identifiable or rigorous focusing is demanded of the human eye Removing the monitor base Before you can use a swivel arm or a wall bracket you must remove the monitor base 1 Covers 2 Screws 18 English 26361 628 2100 1 5 19 Color monitor 4612 FA gt the monitor on its face on a soft surface N The monitor surface is susceptible to scratching Pull off the two cover plates 1 in the direction of the arrow gt Remove the four screws 2 on the rear of the monitor You can now mount a swivel arm or a wall bracket as per VESA FPMPMI with 100 mm hole spacing For instructions on how to mount the swivel arm or wall bracket please see the documentation for the swivel arm or wall bracket Technical data Dimensions and weight LCD monitor Visible diag
20. lish 21 Color monitor 4612 FA Monitor port DVI 1 TMDS Data2 1 TMDS Data 1 3 TMDS Data5 Shield TMDS Data2 TMDS Data3 TMDS Clock Shield en TMDS Data 2 4 TMDS Data3 TMDS Clock Shield TMDS Data4 TMDS Clock wi mk oaj A _ o rn o DDC Clock Hot Plug Detect Analog Red 7 DDC Data TMDS Data0 Analog Green Analog Vertical Sync TMDS Data0 Analog Blue o TMDS Data1 TMDS Data 0 5 Analog Horizontal Shield Sync 10 TMDS Data1 20 TMDS Data5 Analog Ground Error handling Should an error occur first check the following points If the distortion is still not eliminated the monitor should if possible be checked on another computer and or with another data cable If you are unable to solve the problem please inform our Help Desk The display is too small or not centered The monitor recognizes an undefined mode see Technical data gt Adjust the picture size and position see Operation of the monitor No display power indicator does not light gt Check whether the monitor is switched on gt Check whether the power cable on the monitor is connected correctly gt Check whether the monitor socket of the computer is live 22 English 26361 628 2100 1 5 19 Color monitor 4612 FA No display power indicator lights gt Check whether the computer is switched on gt Check whether the
21. livery does not correspond to the delivery note notify your local sales outlet immediately It is recommended not to throw away the original packing material Keep it for future transportation 26361 628 2100 1 5 19 English 7 Color monitor 4612 FA Installing an ergonomic video workstation Before you set up your equipment you should select a suitable position for working at the monitor Please observe the following advices when installing a video workstation gt gt gt gt gt gt gt gt permissible permissible reaching sector reaching sector 600 mm Avoid direct and reflected glare Avoid glare from electric Position the keyboard where it lighting is easiest to reach preferable viewing sector approx 90 9 m v 17 60 Ly permissible 65 viewing sector permissible viewing sector approx 90 and more Position the monitor for Keep ventilated areas clear Remember to maintain correct optimum viewing The viewing posture distance to the monitor should be approximately 50 cm Depending on the situation the use of a swivel arm or wall bracket VESA FPMPMI which are included in the accessories may be advisable For this purpose the monitor base must be removed beforehand as described in chapter Removing the monitor base Connecting the monitor Please note the information provided in the Safety section in the chapter Important not
22. ndow Auto Adjust 14 English 26361 628 2100 1 5 19 Color monitor 4612 FA Adjusting picture a s Position Up Down Lett an e the picture up down to the left or to the right Right Auto Adjust Adjusting picture position automaticaly picture position automatically Making manual picture adjustments Image Adjust Eliminating vertical picture interference Adjusting picture definition and clarity fine adjustment Auto Adjust Adjusting picture size and picture definition Setting color temperature and color ratio Color Control The warmth of the screen colors is set using the color temperature The color temperature is measured in K Kelvin The color ratio of all preset color temperatures can be modified Custom Preset 1 2 3 4 5 Select a preset color temperature with the button or Y 1 9300 Kelvin 2 7500 Kelvin 3 6500 Kelvin 4 5000 Kelvin 5 4200 Kelvin With the SELECT button you can change to the freely defined adjustment of the red green and blue color ratio and back to the preset color temperature again Rea Increase or decrease red ratio Increase or decrease green ratio Blue Increase or decrease blue ratio Setting the picture quality Smoothing This function can only be used when the full screen mode Expansion Mode is switched on Text Mode Set mode for the optimum display of texts Normal Mode Set mode for the optimum display of texts and grap
23. of the previous display for a time This phenomenon is not due to a monitor defect but to the technology used IPS display with large viewing angle IPS In Plane Switching 26361 628 2100 1 5 19 English 23
24. omic video workstation Connecting the Connecting cables to the monitor Connecting cables to the computer Operation of the monitor Adjusting height rake and rotation Adjusting portrait format Switching the monitor on off Notes on power management Changing the monitor settings Notes on ergonomic color adjustment D Removing the monitor Dasa EE EE VESA DDC compatible VGA interface Preset operating modes Pin assignment D SUB usa Monitor OOTY u u u Error Elie WEE 26361 628 2100 1 5 19 English Introduction Your new LCD Liquid Crystal Display monitor 4612 FA offers numerous features and functions for example TFT display Thin Film Transistor active matrix e minimal space requirements thanks to slim housing optimum ergonomic characteristics totally distortion free excellent picture definition and color purity right into the corners high degree of brightness and good contrast high resolution 1280x1024 for displaying the information content of a conventional 21 inch screen with CRT Cathode Ray Tube e presentation of up to 16 7 million colors in conjunction with an appropriate screen controller automatic scanning of all horizontal frequencies from 31 to 82 kHz and all r
25. onals Dot pitch Screen size Maximal resolution Dimensions W x H x D incl monitor base Weight Accessories Storable display modes Electrical data Video Synchronization Horizontal frequency Refresh rate Maximum pixel rate Power supply Total power consumption 46 cm 0 28 mm 359 mm x 287 mm 1280 x 1024 pixels 454 mm x 462 562 mm x 218 mm approx 9 kg Power cable 1 8 m Data cable 5 ft 2 m D SUB to DVI A Data cable 5 ft 2 m DVI A to DVI A 26 analog positive 0 7 V 75 Q digital DVI Separate Sync TTL positive or negative PP Composite Sync TTL positive or negative Sync On Green 31 kHz 82 KHz multi scanning 56 Hz 85 Hz 135 MHz switches automatically 100 V 120 V 50 Hz 60 Hz Hz 0 6 A 220 V 240 V 50 Hz 60 Hz 3 Hz 0 3 lt 65 W ON Normal mode lt 5 Win the energy saving mode standby mode suspend mode and OFF mode 26361 628 2100 1 5 19 English 19 Color monitor 4612 FA Environmental conditions Environment class 3K2 IEC 721 Rated range of operation 15 C 35 C Humidity 20 95 85 96 Limit range of operation 5 C 35 C Humidity 20 95 85 Condensation must avoided VESA DDC compatible VGA interface Your monitor is equipped with a VESA DDC compatible VGA interface VESA DDC Video Electronics Standard Association Display Data Channel is used as the communications int
26. ot a signal appears at the other video input If no signal is present at the current video input the monitor switches over to the other input Last Detect Switch on the Last Detect mode As soon as a signal appears at a video input the monitor switches over to that input Selecting signals for DVI connection DVI select The DVI connection enables operation with analog or digital signals With this function you can depending on the graphics card you use switch over between the analog and the digital mode Digital Switch on the digital mode The monitor processes the signals of the digital port Switch on the analog mode The monitor processes the signals of the analog port Setting the language for the OSD menu Language Select The OSD menu can be displayed in various languages You can choose from English default setting German French Spanish Italian Swedish and Japanese 16 English 26361 628 2100 1 5 19 Color monitor 4612 FA Setting position for the OSD menu OSD Position Up Down Left Shifting the OSD menu up down to the left or to the right Right Setting display time for the OSD menu OSD Turn Off Time You can select between 10 20 30 60 and 120 seconds If the adjusted time has run out without the settings being saved the OSD menu is automatically closed Locking the OSD menu OSD Lock Out The OSD menu can be locked to prevent accidental or unauthorized changes to the monitor se
27. s TCO 99 VESA DDC und DPMS sind eingetragene Warenzeichen der Video Electronics Standards Association Alle Rechte vorbehalten insbesondere auch auszugsweise die der bersetzung des Nachdrucks der Wiedergabe durch Kopieren oder hnliche Verfahren Zuwiderhandlungen verpflichten zu Schadenersatz Alle Rechte vorbehalten insbesondere f r den Fall der Patenterteilung oder GM Eintragung Lieferm glichkeiten und technische nderungen vorbehalten Copyright Fujitsu Siemens Computers GmbH 2000 VESA DDC and DPMS are registered trademarks of Video Electronics Standards Association All rights including rights of translation reproduction by printing copying or similar methods even of parts are reserved Offenders will be liable for damages All rights including rights created by patent grant or registration of a utility model or design are reserved Delivery subject to availability Right of technical modification reserved Contents e ME Notational conventions Important notes Safety Cleaning RTE lee FCC Class B Gormplianee SISlerment uu u u u jaticesssecdecessaaccdssiecsvesscaguaesnsaddntasagdecvesdaatvescadevescs Declaration of Conformity Power cable Energy Star Guidelines Mote gt EE Disposal and recy Clin ET Checking the contents of the consignment Installing an ergon
28. set only those resolutions and refresh rates specified in the Technical data chapter Otherwise you may damage your monitor If you are in any doubt contact your sales outlet or our Help Desk Keep this Operating Manual together with your device If you pass on the device to third parties you should include this manual Cleaning Always pull out the power plug before you clean the monitor Do not clean any interior parts yourself leave this job to a service technician Do not use any cleaning agents that contain abrasives or may corrode plastic Ensure that no liquid will run into the system Ensure that the ventilation areas of the monitor are free The display surface of the LCD monitor is sensitive to pressure and scratches Clean it only using a soft slightly moistened cloth Wipe the monitor housing with a dry cloth If the monitor is particularly dirty use a cloth which has been moistened in mild domestic detergent and then carefully wrung out Transport Transport the monitor with care and only in its original packaging or another corresponding packaging fit to protect it against knocks and jolts Never drop the LCD monitor danger of glass breakage 26361 628 2100 1 5 19 English 3 Color monitor 4612 FA FCC Class B Compliance Statement If there is an FCC statement on the device then The following statement applies to the products covered in this manual unless otherwise specified herein The statement for
29. software Operation of the monitor The monitor offers the following possibilities that enable it to be optimally adjusted for the respective user and the respective situation Adjusting height rake and rotation The monitor height can be adjusted within a range of approx 2 in 70 mm gt Grasp the monitor with both hands on the right and left edge of the housing and move it upward or downward The rake of the monitor can be adjusted by 5 forward and 30 back from its vertical position gt Grasp the monitor with both hands on the right and left edge of the housing and adjust it to the desired rake The monitor can be rotated by 90 from its center position gt Grasp the monitor with both hands on the right and left edge of the housing and rotate it into the desired position Adjusting portrait format The monitor can be turned from the wide format landscape mode into the high format position portrait mode gt Grasp the monitor with both hands on the right and left edge of the housing move it into the highest position and turn it clockwise until it is in the portrait position gt Press the RESET button with the OSD menu switched off to switch the OSD On Screen Display menu from the landscape mode into the portrait mode also see the section Monitor settings using the OSD menu 10 English 26361 628 2100 1 5 19 Color monitor 4612 FA You must use corresponding software pivot soft
30. to the mode with the highest energy saving effect Function Monitor Monitor operating is dark normally Power consumption normal reduced lt 65 W to lt 5 W If your computer detects inactivity no input it sends an appropriate signal to the monitor to reduce the power consumption energy saving mode The power indicator of the monitor changes color to indicate the status change Once an input is made at the computer the screen contents are redrawn and full power is restored For detailed information on how energy saving mode operates refer to the Operating Manual or Technical Manual of your computer system a power consumption of up to 5 W is maintained to feed the circuit for redrawing D When the monitor is switched to the energy saving mode by the power management the screen contents To completely switch off the power consumption switch off the computer or pull the plug of the monitor power cable out of the monitor socket of the computer Changing the monitor settings When putting the monitor into operation for the first time the screen display should be optimally adapted to the screen controller used and adjusted in accordance with your needs Basic monitor settings with the floppy disk supplied If one of the operating systems Windows for Workgroups Windows 95 98 Windows NT or OS 2 with Windows emulation installed is used the basic monitor settings can be set with the floppy disk supplied gt Insert the suppl
31. ttings gt Press and hold down the SELECT button in the OSD Lock Out setting window and briefly press the A button of the control panel To release the locked OSD menu again you must carry out the same step Activating the factory settings Factory Preset Factory settings are available for picture definition picture position picture size and colors in the preset operating modes see table in the chapter Technical data You can choose whether you want to reset the values for the input D SUB DVI or for both inputs gt Select Factory Preset and press the RESET button to reset the selected settings to the factory settings If you only wish to activate the factory settings for one menu item mark the corresponding menu item press the RESET button and then the SELECT button Displaying note on resolution Resolution Notifier The optimum resolution for this monitor is 1280 x 1024 With the function activated ON a message appears on the screen after approx 30 seconds if a different resolution has been selected Displaying graphics mode Display Mode Under Display Mode you find information on the display mode currently set Displaying monitor data Monitor Information You will find the model designation and the serial number of the monitor under Monitor Information 26361 628 2100 1 5 19 English 17 Color monitor 4612 FA Notes on ergonomic color adjustment If you select colors for the display in your applicat
32. ware so that the screen display is also shown in the portrait mode This software is available from specialized dealers To reset the monitor to the landscape mode the monitor must be turned counter clockwise With the RESET button with the OSD menu switched off you can switch over the OSD menu again Switching the monitor on off ON OFF switch Power indicator Buttons for the OSD menu On Screen Display The ON OFF switch 1 is used for switching the monitor on and off The power indicator 2 glows green when the monitor and computer are switched on The power indicator glows amber when the monitor does not receive a video signal or is in the energy saving mode The power indicator goes off when the monitor is switched off When you switch on the computer system you must proceed in the following order gt First switch the LCD monitor on with the ON OFF switch 1 gt Then switch on the computer read the Notes on power management of the monitor in this chapter D If your computer has a power management function energy saving mode you should 26361 628 2100 1 5 19 English 11 Color monitor 4612 FA Notes on power management If your computer is equipped with power management the monitor can support this function fully Here the monitor does not distinguish between the individual energy saving modes of the computer standby mode suspend mode and OFF mode as it is capable of immediately switching in
Download Pdf Manuals
Related Search