Home

Fujitsu FI-5015C Photo Scanner User Manual

1. ATTENTION e The documents on ADF paper chute should be less than 50 sheets S 2 Setting more than 50 sheets may cause paper jam or reading problem e When scanning with the ADF make sure that no documents are placed on the flatbed Any documents on the flatbed will raise the flatbed cover and cause deterioration of image quality 2 Fan documents as follows 1 Lightly grip both ends of the documents with both hands and bend the documents as fol lows SNOIIVH3dO YANNVOS OISVE 2 Hold the documents firmly with both hands and bend them back as follows so that the bent section rises up in the middle of the stack as shown below 3 Repeat steps 1 and 2 a couple of times 4 Rotate documents 90 degrees and fan again 3 Align the top of the documents FT A fi 5015C Image Scanner Operator s Guide 15 16 4 Load the documents on the ADF paper chute ATTENTION Set the documents face up in the ADF paper chute with the upper edge of the documents downwards 5 Adjust the side guides to the width of the documents Move the side guides so that they touch both sides of the documents If there is any clearance between the side guides and the edges of documents the scanned image may be skewed 6 Scan the documents For how to scan the document
2. 1592 05 20 fi 5015C Image Scanner Operator s Guide co FUJITSU CONTENTS Regulatory Information ceres iii Note Pel mm V E Safety Precautions cw ed decreuit viii Chapter 1 NAME OF PAHTS co o eene eani rera ru nnns 1 UL C 2 1 2 Operator Panel ae 5 Chapter 2 BASIC SCANNER OPERATIONS 7 2 1 Turning ON OFF the Scanner 8 2 2 Loading Documents on ADF 12 2 3 Loading Document on Flatbed 17 2 4 Scanning Documents c c ss ss 19 2 5 How to use the Scanner Driver 22 2 6 Image Scanning 36 Chapter 3 MAINTENANCE scenic anses 37 3 1 How to clear the paper jam 38 3 2 2 39 3 3 Replacing 44 fi 5015C Image Scanner Operator s Guide Chapter 4 TROUBLESHOOTING MM 53 4 1 Error Indications in the Function Number Display 54 4 2 Troubleshooting iini ux
3. 56 APPENDIX SCANNER SPECIFICATIONS AP 1 APPENDIX B Using Scan or Send to button AP 3 APPENDIX GLOSSARY OF AP 7 INTRODUCTION Thank you for purchasing the fi 5015C Color Scanner This document describes how to handle fi 5015C and basic operation methods Before you start using fi 5015C be sure to thoroughly read this manual to ensure correct use This document describes the basic operation methods to perform scanning by using ScandAll PRO The version of ScandAll PRO bundled with this product is subject to change without notice in which case the screenshots captured in this document may differ from the actual displayed image For more information about ScandAll PRO refer to the separate ScandAll PRO V2 0 User s Guide Regulatory Information FCC Declaration This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this
4. 15 AP 16 TWAIN Technology Without Any Interesting Name A standard for API Application Program Interface or protocol for imaging devices scan ners digital cameras etc developed by TWAIN Working Group In order to use devices that comply with this standard it is necessary to install driver software based on the same standard Ultrasonic sensor A type of sensor for detecting multi feeding by ultrasonic sound Scanners detect multi feeding by recognizing differences in the amount of ultrasonic waves that penetrates the documents USB Universal Serial Bus An abbreviation for Universal Serial Bus A standard for interfaces used to connect devices such as key boards scanners etc Up to 127 devices can be connected through this interface USB devices can be plugged unplugged without turning off their power Data transfer rates are different between the Low speed mode 1 5Mbps and High speed mode Max 12Mbps White level follower A function to correct the difference between white colors in unbleached paper e g wood containing paper etc and in scanned images White Reference Stripe The white part located in the ADF that defines the lightest area in an image causing all other areas to be adjusted accordingly INDEX A ADF automatic document feeder 2 C Checking document condition 12 Cleaning Materials 39 Cleaner F 1c xu ERES 39 Con
5. Millimeters Inches and Pixels are available Startup tab Select this tab for setting the Scanner Operation Panel Filter tab Select this tab for setting the image processing filter s Page Edge Filler Fills up the margins of the scanned documents with a selected color Digital Endoser A character string such as the alphabet and numbers can be added in the scanned document SNOIIVH3dO HHNNVOS OISVE Advance button Click this button for settings of the advanced image processing You can set Dropout Color Reverse etc Also Gamma Pattern by custom settings Config button Click this button for configuring the Setting Files You can save the changed settings as a Setting File From next scanning the settings are quickly changed by using these Setting Files For details of each function refer to the TWAIN Scanner Driver Help fi 5015C Image Scanner Operator s Guide 27 B ISIS Scanner Driver ISIS Scanner Driver is designed for scanning documents with FUJITSU image scanner fi series by using application software that complies with the ISIS standard The following describes the procedure with examples of QuickScan for ordinary scanning by using this driver The procedure may vary depending on your application If you use an application other than QuickScan please refer to its Guide or Help for further information 1 Procedure for Basic Scanning Operation 1 Startup the application From the Start me
6. Symbols Used In This Manual ATTENTION rey eor This symbol alerts operators to particularly important information sure to read this information This symbol alerts operators to helpful advice regarding operation A TRIANGLE symbol indicates that special care and attention is required The drawing inside the triangle shows the specific caution A CIRCLE with a diagonal line inside shows action which users may not perform The drawing inside or under the circle shows the specific action that is not allowed Outline characters on a colored background show instructions users should follow It may also include the drawing that shows the specific instruction Screen Examples In This Manual The screen examples in this manual are subject to change without notice in the interest of product improvement If the actual displayed screen differs from the screen examples in this manual operate by following the actual displayed screen while referring to the User s Manual of the scanner application you are using The screenshots in this manual were captured from TWAIN scanner driver ScandAll PRO Image Capturing Utility Software ISIS scanner driver QuickScan Pro image capturing software and Adobe Acrobat fi 5015C Image Scanner Operator s Guide vii Precautions In the following warnings power cable may refer to the AC cable connected t
7. generally the gamma value is set to 1 Grayscale A method for realizing the gradation from black to white on the scanned image For example when scanning monochrome documents the computer recognizes the docu ments as sets of black and white dots In the Gray scale method each dot contains data regarding density of black The original gradation of the documents is realized as the gradation of the density data Halftone processing Any method used to reproduce a photograph which includes a shade as an image com posed of dots namely a binary image Dithering and error diffusion processing are examples of halftone processing Image emphasis Density is decreased for lighter but not completely white areas adjacent to black areas Weakening this emphasis eliminates spot noise or produces softened images Image processing An image is scanned with specified parameters Interface The connection that allows communication from the computer to the scanner Inversion Reverse image reading In reverse image reading data is changed from black to white and vice versa fi 5015C Image Scanner Operator s Guide 11 12 IPC preset mode While reading binary images it is necessary to set the scanner according to the quality of the sheet to be read In this mode these settings can be performed in advance by cor responding each setting to a pattern number ISIS Image Scanner Interface Specification A standard of API Applicati
8. trast Left 0 000 0 000 j Contras Width 8 268 Length 11 533 Advance Close Reset Option About TWAIN driver Press F1 key to show help Data Size about 1 1MB You can set the TWAIN Scanner Driver on this window The following describes the main setting items For details on each functions refer to TWAIN Scanner Driver Help appears by pressing Help or F1 button SNOIIVH3dO YANNVOS OISVE Resolution Specifies the resolution of scanning It can be specified by selecting from the list a default value or custom specifies any resolution in 1 dpi unit By marking the Predefine checkbox you can select one from three predefined set tings as Best Better and Normal to scan documents instead of setting details by yourself Otherwise you can change the predefined settings of Best Better and Normal by clicking the button Scan Type Specifies the feeding method ADF scanning or Flatbed scanning Paper Size Selects the size of documents to be scanned from the list Windows for customizing the paper size will appear when you click on by the list You can save any document size as a customized setting up to three or for changing the order of the paper size in the list fi 5015C Image Scanner Operators Guide 25 26 Image Mode Specifies the image type for the scanned documents Black amp White Documents are scanned in binary black an
9. 2 16 T Troubleshooting 53 Turning ON OFF the Scanner 8 TWAIN Scanner Driver 22 fi 5015C Image Scanner Operator s Guide IN 1 USB connector Using the Scan or Send to button IN 2 fi 5015C Image Scanner Operator s Guide P3PC 1592 05ENZO Date of issuance October 2011 Issuance responsibility PFU LIMITED e The contents of this manual are subject to change without notice e PFU LIMITED is not liable whatsoever for any damages resulting from the use of this scanner and procedures described in this manual profit loss due to defects and any claims by a third party e Copying of the contents of this manual in whole or in part and copying of the scanner application is forbidden under the copyright law
10. Offset OK Cancel Apply You can confirm the following information on this panel e Total number of scans with ADF and Flatbed and Pick roller counter approximate number of scans after resetting the counter 46 3 3 Replacing Consumable The following message may appear while using the scanner lt is about time to replace the consumable Please replace Pick Roller in paper feeder if the feeding capability is deteriorated Regarding how to replace the pad please refer to the Operator s Guide Code 0542005 This message not display again Wams again after scanning 100 pages cm ue Replace consumables when this message is displayed After clicking the Ignore button this message will disappear and scanning will continue Please replace the consumable as soon as possible As a default this message appears again after 100 scans If you do not wish this message to display click the This message not display again To stop scanning and replace the consumable click the Cancel button 3 3 3 Replacing the Pad ASSY 1 Remove all documents from the ADF paper chute JONVNALNIVN MESS 2 Open the ADF Be careful the ADF may close and pinch your AN CAUTION fingers fi 5015C Image Scanner Operator s Guide 47 3 Remove the snap in Pad ASSY by pinching the upper part of the pad clamp as shown in the following photo 4 Install new Pad ASSY by the reverse
11. Profile TIFF Edit Profile Grayscale JPEG 24 bit color scanning saved as JPEG Path e Documents and Settings furuse My Documents File Name untitled jpg Browse First Batch Ius Next Page C Custom Batch Cancel Scanned images are displayed on the window Refer to the QuickScan Overview or the QuickScan Help for further information on functions and operations of QuickScan After the installation of QuickScan it is reg istered in the Start menu 30 2 5 How to use the Scanner Driver 2 Configuration Window of ISIS Scanner Driver tab Properties for Fujitsu fi 5015C on None ca syout More Gamma About Mode pxkzwne Dots per inch 300 v Brightness E lt Contrast C Manual Z Halftone O None dp Paper Source Automatic o Z z TJ O U Mode m Selects a color mode suitable for the purpose from the menu T Black amp White Documents are scanned in binary black and white a 256 level Grayscale Scans data by 254 shades of gray plus black and 9 white This mode uses 8 bits per pixel This mode is switable for scanning monochrome photographs 24 bit Color Scans data as full colored image using 24 bits per pixel This mode is suitable for scanning color photo graphs Dots per inch Specifies the number of pixels dots per inch Select a fixed resolution from the list 75 100 150 200 300 400 500 600 A hi
12. Scan button on the dialog box fi 5015C Image Scanner Operators Guide 23 2 SNOIIVH3dO HHNNVOS OISVE 24 gt The images of scanned documents are displayed on ScandAll PRO window ScandAll PRO My Documents image0001 tif 1 1 Elle Scan Edit View Page Mark zoom Tool Help uit mE ethno oa i 2 A TART BS Elle im 59 8 2x1 16 14 1 1 Pages With ScandAll PRO the scanned image will not be displayed when you clear the Display scanned images immediately after scanning check box in the Scan Settings dialog box 8 Save the scanned images The scanned image is saved when the Save to file check box is seleted in the Scan Settings dialog box If not select File menu Save As to save the file If you wish to start another scanning return to procedure 4 9 End ScandAll PRO Select Exit from the File menu 2 5 How to use the Scanner Driver 2 Setting Window for TWAIN Scanner Driver TWAIN Driver 32 Image Scanner fi 5015C 32MB Browse Setting Files Joo Current Setting cj Config Resolution Scan Type B 300 x 300 Y 25 ADF Front Side M a Paper Size Predefine 44 210x297 mm 2 r Front 0 1 2 3 4 5 6 i 8 9 Image Mode Brightness AE Black amp White E Black White Threshold 14 Static Threshold 128 Scanning Areal inch 4
13. Windows Server 2008 R2 Standard Windows 7 Windows 7 Home Premium operating system 32 64 bit Windows 7 Professional operating system 32 64 bit Windows 7 Enterprise operating system 32 64 bit Windows 7 Ultimate operating system 32 64 bit Where there is no distinction between the different versions of the above operating system the general term Windows is used Adobe Acrobat Adobe Acrobat All the descriptions in this manual assume the usage of Adobe Acrobat bundled with this product However Adobe Acrobat may be upgraded without notice If the descriptions differ from the screens actually displayed refer to the Acrobat s Help Manufacturer PFU LIMITED International Sales Dept Imaging Business Division Products Group Solid Square East Tower 580 Horikawa cho Saiwai ku Kawasaki shi Kanagawa 212 8563 Japan Phone 81 44 540 4538 O PFU LIMITED 2006 2011 About Maintenance The user must not perform repairs on this scanner Contact the store where you purchased the scanner or an authorized FUJITSU Image Scanner service provider to make repairs to this product vi Warning Indications Used In This Manual ZAWARNING ZN CAUTION This indication alerts operators to an operation that if not strictly observed may result in severe injury or death This indication alerts operators to an operation that if not strictly observed may result in safety hazards to personnel or damage to equipment
14. equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures eReorient or relocate the receiving antenna eIncrease the separation between the equipment and receiver eConnect the equipment into an outlet on a circuit different from that to which the receiver is located eConsult your dealer or an experienced radio TV technician FCC warning Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTICE The use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC rules The length of the AC cable must be 3 meters 10 feet or less fi 5015C Image Scanner Operator s Guide iii Canadian DOC Regulations This digital apparatus does not exceed the Class B limit for radio noise emissions from digital apparatus set out in the Radio interference Regulations of the Canadian Department of Communications This Class B digital apparatus complies with Canadian ICES 003 Le pr sent appareil num rique n met pas de parasites radio lectriques d passant les limites applicables aux appareils num riques de la classe B et prescrites dans le R glement sur le brouillage radio lectrique dict es par le Minist re des Communications du Canada Cet a
15. of roller are cleaned e Pinch rollers Clean Pinch roller softly not to damage its surface Try to remove any black stain which may degrade the performance of paper feeding 3 Push in the center of the ADF to return it to its original position until it clicks ATTENTION Close the ADF until it clicks Paper jams or feeding errors may occur if the ADF is not closed completely 42 3 2 Cleaning 4 Open the Flatbed cover and clean the following locations ATTENTION The glass surface under the ADF becomes hot during the operation of the scanner JONVNALNIVN MESS fi 5015C Image Scanner Operators Guide 43 3 3 Replacing Consumable Note the inside of ADF automatic document feeder Z CAUTION may become hot during the operation 3 3 1 Part number and Replacement cycle The following table lists the consumable used in the scanner Be sure to keep some consumables in stock The customer is required to replace consumable periodically Otherwise the scanner may not func tion properly Part number and recommended replacement cycle is No Name Part Number Replacement Cycle 1 Pad ASSY PA03209 0550 Up to 20 000 sheets or 1 year 2 Pick roller unit PA03209 0551 Up to 100 000 sheets or 1 year Replacement cycle may be shortened depending on the type of scanned documents The above replacement cycle is estimated with the following paper quality Woodfree paper or Plain paper ATTENTION Use on
16. procedure of removing ATTENTION Make sure that the Pad ASSY is firmly attached When the Pad ASSY is not correctly attached document jams or other feeding errors may occur 5 Press the center of the ADF to close it until it clicks 6 Reset the pad counter 1 Check that the scanner is connected to your PC and turn on the scanner 2 Open the Scanners and Cameras from the control panel of your PC 3 Open the Properties of fi 5015C from the Scanners and Cameras gt The Properties of fi 5015C dialog box appears 48 3 3 Replacing Consumable 4 Click the Device Set tab fi 5015C Properties General Events as aqcement MR Diagnosis Dewicelnto amp DeviceSet About Page Counter Total Page Count amp DF 100000 pages Total Page Count FB 70 pages Pad 20000 pages Pick Roller 100000 pages L Power saving 15 minutes Power Control il Offset 3 5 After clicking Clear button beside Pad in Page Counter click button gt The following window appears JONVNALNIVN MESS Attention Cancel Click the button The Pad counter returns to 0 fi 5015C Image Scanner Operators Guide 49 3 3 4 Replacing the Pick roller unit 1 Remove all documents from the ADF paper chute 2 Open the ADF Be careful the ADF may close and pinch your fingers CAUTION 3
17. scanner or use the scanner s surface top to perform other work Improper installation might cause injuries and equipment failure Firmly insert the power plug Firmly insert the power plug as far it can go into the power outlet o Avoid any contact when scanner is in use Avoid touching any scanner mechanism during scanning since this may cause injuries gt Do not use the scanner immediately after moving it from a cold place into a warm room Do not use the device immediately after moving it from a cold place into a warm room This may cause condensation which might lead to scanning errors Let the device dry about one or two hours before you use it Before moving the scanner disconnect the power plug from the power outlet Do not move the scanner with the power and interface cables connected as this might damage the cables causing fire electric shock or injuries Before moving the scanner be sure to disconnect the power plug from the power outlet and all other data cables Make sure that the floor is free of any obstruction Protect the scanner from static electricity Install the scanner away from strong magnetic fields and other sources of electronic noise Also protect the scanner from any static electricity as this might cause the scanner to malfunction Disconnect the power plug from the power outlet when the scanner is not used for a long period of time When the scanner is not goin
18. such as smoke strange smells or noises disconnect immediately the power plug in order to turn out the scanner Make sure that any smoke coming from it has stopped before contacting the store where you bought the scanner or an authorized FUJITSU scanner Service provider e Do not use aerosol sprays near the scanner Do not use any aerosol sprays or alcohol based sprays to clean the scanner Dust blown up by strong air from the spray may enter the inside of the scanner This may cause the scanner to fail or malfunction Sparks caused by static electricity generated when blowing off dust and dirt from the outside of the scanner may cause a fire fi 5015C Image Scanner Operators Guide ix CAUTION Do not install the scanner on unstable surfaces Make sure that the scanner is installed on a flat level surface and that none of its parts extend beyond the surface top such as a desk or table Do not install the scanner on unstable surfaces Install the scanner on a level surface that is free of vibration to prevent it from falling Install the scanner on a strong surface that will support the weight of the scanner and other devices OS Do not block the ventilation ports Do not block the ventilation ports Blocking the ventilation ports generates heat inside of scanner which may results in fire or scanner failure Do not place heavy objects or stand on top of the scanner Do not place heavy objects on the
19. the window of ISIS Driver Select the Scan tab and click the Scanner Settings on the Profile Editor window Scan Profile Editor gt Format and Naming v Show continue dialog after scan Use Flatbed if feeder is empty Image Processing Advanced options after scan C Pages are rotated OCR Index Export Batch Enable software auto color detection Advanced options before scan Advanced features Scan parameters Scan mode Simplex Scan type Black and White Page size Letter 8 5 x 11 in DPI 300 Scanner Settings V Save scanner settings after scanning completes The configuration window of ISIS driver appears fi 5015C Image Scanner Operator s Guide 29 2 SNOIIVH3dO YANNVOS OISVE 7 Configure settings for scanning and click the OK button Properties for Fujitsu fi 5015C on None Main Layout More Gamma About Mode Black amp White Dots per inch mo Brightness E lt Contrast C Manual El Halftone None Paper Source Automatic For details on this dialog box refer to Configuration Window of ISIS Scanner Driver on page 31 8 The Profile Editor window appears Click the OK button to return to New batch dialog 9 Load the documents on the scanner 10 Click the Scan button New Batch Select a Profile lt use preview settings Add
20. 4 ONILOOHS3 Ianou L fi 5015C Image Scanner Operator s Guide 55 4 2 56 Troubleshooting Be careful the inside of ADF automatic document feeder may become hot during the operation If a problem occurs check the following items before contacting the manufacturer s authorized ser vice center Symptom Check this item Remedy Scanner does not turn on Is the main switch turned on Turn the main switch on Have you pushed the power button Push the power button Are the AC cable and AC adapter properly connected to the scanner Correctly connect the AC cable and the AC adapter Disconnect the AC cable and the AC adapter from the scanner then con nect them again If this does not restore the power sup ply contact the store where you pur chased the scanner or an authorized FUJITSU scanner service provider Is Windows normally started up Push the power button again after completely starting up Windows Scanning does not start Are the documents loaded correctly on the ADF paper chute Load the document correctly on ADF paper chute Is the ADF closed completely Close the ADF completely Is the USB cable properly con nected Correctly connect the cable When a USB hub is used check the hub s power supply Does the Function Number Display indicates an alarm or an error When the Function Number Display indicates an alarm or an
21. ADF as follows to return your scanner to its original state Be careful the inside of ADF automatic document AN CAUTION feeder may become hot during the operation E Cleaning Method ATTENTION The glass surface under the ADF becomes hot during the operation of the scanner Before you start to clean the inner parts of the scanner disconnect the AC adapter from the power outlet and wait at least 15 minutes to let the glass cool down JONVNALNIVN MESS 1 Open the ADF Be careful the ADF may close and pinch your Z CAUTION fingers 2 Clean the following locations with a lint free cloth moistened with the Cleaner F1 Pick roller unit Pinch rollers Pad ASSY fi 5015C Image Scanner Operators Guide 41 ATTENTION It may take long before the cleaner vaporizes if a large quantity is used When cleaning the scanner parts dampen a cloth with modest quantities of the cleaner In addition wipe off the cleaner completely with a soft lint free cloth to leave no residue on the surface of the cleaned parts e Pad ASSY Wipe Pad ASSY with the cloth in the direction from bottom to top Pick Springs Sensor lever ATTENTION Be careful not to hook the pick springs sensor lever and mylar sheet near the Pad ASSY e Pick roller unit Wipe the Pick roller unit by moving the cloth from side to side of rollers Rotate the rollers forward with your finger and repeat the wiping procedure until all surface
22. AP 8 Automatic size skew detection A function that automatically detects the documents page size and adjusts output data to the detected page size Document skewing is automatically detected and corrected for the output image Brake roller A roller that prevents two or more sheets of paper from being fed simultaneously into the ADF Brightness Refers to the brightness of scanned images in this manual Canadian DOC Regualtions A standard issued by Industry Canada a department of the Canadian government which sets out the technical requirements relative to the radiated and conducted radio noise emissions from digital apparatus CCD Charged Coupling Device Image Sensor A semiconductor device inside the scanner that registers light reflected from the original image and converts it into a digitized electronic form CCD technology is the basis of high quality image acquisition in scanners cameras and other specialized devices Cleaning paper Sheets used with the F1 cleaner for cleaning the rollers pick rollers pinch rollers etc and complete document path in the scanner Used in daily maintenance of the low ume production scanner to reduce paper transport problems Note these sheets are not meant to replace the more thorough periodic cleaning of the scanner Cleaning sheet Adhesive sheets used for cleaning the rollers pick rollers pinch rollers etc and com plete document path in the scanner Used in daily mainte
23. ASSY dirty Clean the Pad ASSY Refer to the Operator s Guide 3 2 3 Cleaning the Is the Pad ASSY worn out Replace the Pad ASSY Refer to the Operator s Guide 3 3 3 Replacing the Pad ASSY Paper is not fed paper feed error occurs fre quently or document stops midway The generated image are elongated Does the document satisfy the Doc ument Quality described in Section 2 2 1 Scan the documents by Flatbed Is the thick document placed on the Flatbed Remove the document from the Flat bed Is the Pick roller dirty Clean the Pick roller Refer to the Operator s Guide 3 2 3 Cleaning the ADF Is the Pick roller worn out Is the Pick roller dirty Replace the Pick roller ASSY Refer to the Operator s Guide 3 3 4 Replacing the Pick Roller Clean the Pick roller Refer to the Operator s Guide 3 2 3 Cleaning the ADF There is a shadow on the leading edge of the generated image Are the Pinch rollers dirty Clean the Pinch rollers Refer to the Operator s Guide 3 2 3 Cleaning the ADF on page 41 Have you adjusted the offset the scanning starting position Adjust the Sub scan Setting on Scanners and Cameras in the control panel Multi feed means that more than 2 papers are fed at the same time fi 5015C Image Scanner Operator s Guide 57 4 ONILOOHS3 Ianou L 58 APPENDIX A Basic Specifications SCANN
24. ER SPECIFICATIONS Item Specifications Dimension mm Width Depth Height 328 12 9 in 447 17 6 in 175 6 9 in Weight kg Ib 5 5 11 7 Ibs Input power Voltage AC100 to 240V Phases Single Frequency 50 60Hz Power consump During operation 24W or less tion Stand by 5 3W or less Operating envi Device status At Operation At Stand by At shipping ronment Temperature 5 to 35 C 20 to 60 C 20 to 60 C 59 to 95 F 4 to 140 F 4 to 140 F Humidity 10 to 85 8 to 95 8 to 95 fi 5015C Image Scanner Operator s Guide AP 1 B Dimensions 175 6 88 in lt 447 17 6 in 175 6 88 in 328 12 9 in Unit millimeters AP 2 APPENDIX B Using Scan or Send to button Settings on the Personal Computer By setting the link of the application software to the Scan or Send to button you can launch the linked application by simply pushing the button 1 Select Start Control Panel 2 Select Scanners and Cameras Properties 3 Select the Events tab 4 Select an Event For the case of Windows XP select an event for starting up any application from the Select an event menu fi 5015C Properties Diagnosis Device Info Device Set About General Events Color Management Choose an event below then select the action to take when that 32 event occurs Select an event E Scan But
25. ITSU faoiste T Cancel Select FUJITSU fi 5015C then click the Select button 4 Load the documents on the scanner For details on loading documents refer to 2 2 Loading Documents on ADF on page 12 and 2 3 Loading Document on Flatbed on page 17 5 Open the TWAIN Driver window Select the Scan menu Scan Settings The Scan Settings dialog box appears Click the Scanner Setting button 22 2 5 How to use the Scanner Driver 6 Configure settings for scanning and click the OK button TWAIN Driver 32 Mi 8888 6 PB ON messem 64MB Browse Setting Files 00 Current Setting xl Config Resolution Scan Type ES 300 300 E la ADF Front Side poy i5 Paper Size Predefine ad 4 210 297mm Enable Multi Image Front Image Mode Brightness Black amp White v E Black White Threshold Static Threshold 8 17 Scanning Areal inch Left 0 000 Top 0 000 DENN Contrast Width 8268 Length 11 693 EEG Advance Preview Reset Option Help About TWAIN driver Press F1 key to show help Data Size about 1 1MB For details about the settings on this window refer to Setting Window for TWAIN Scanner Driver on page 25 You are returned to the Scan Settings dialog box 7 Click the Scan button d When you are using TWAIN you may see the TWAIN Driver setup dialog box again If so click the
26. Paper Size setting Select Paper Size among A4 A5 B5 Select Paper Size ASL in the following Letter and Exective in the following driver screen driver screen TWAIN Driver 32 Image Scanner fi 5015C 32MB Browse Setting Files 00 Curent Setting Config Resolution Scan Type Predefine Enable Sof Front Image Mode Brightness Black amp White E HE Black White Threshold Static Threshold v Je 128 Contrast 14 Scanning Areal inch Let 0000 Top 000 P 4 E width 8 268 Lenath 11 593 Advance Preview Close Reset Option Help About Size about 1 1 18 2 4 Scanning Documents 2 4 Scanning Documents This section explains how to scan documents using 11 PRO as an example 1 Load documents on the scanner For details about loading documents refer to 2 2 Loading Documents on ADF on page 12 or 2 3 Loading Document on Flatbed on page 17 2 Start up ScandAll PRO Select Start All Programs Fujitsu ScandAll PRO ScandAll PRO gt This starts up ScandAll PRO 3 Select the scanner to use Select Select Source from the Scan menu ScandAll PRO My Documents ima 5 Settings rr WE 5 Setti E Batch Scan Settings Ctrl B The Select Scanner dialog box appears Select FUJITSU fi 5015C and click t
27. Remove the Pick roller unit from the scanner 1 Pinch the fixture with your fingers with another hand holding the Pick roller unit 50 3 3 Replacing Consumable 2 Pull the Pick roller unit to the fixture s side gt The Pick roller unit is removed downwards 4 Attach a new Pick roller unit to the scanner JONVNALNIVN MESS Attatch a new Pick roller unit to the scanner in reverse order of removing 1 Set the Pick roller unit inserting an end of shaft into the shaft hole correctly as shown in the following photos ATTENTION Make sure that the end of the Pick roller unit shaft is correctly inserted in the shaft hole Otherwise the ADF will not be closed completely 2 Lock the fixture in the original place to fix the Pick roller unit fi 5015C Image Scanner Operators Guide 51 5 Press the center of the ADF to close it until it clicks 6 Reset the Pick roller counter 1 Check that the scanner is connected to your PC and turn on the scanner 2 Open the Scanners and Cameras from the control panel of your PC 3 Open the Properties of fi 5015C from the Scanners and Cameras gt The Properties of fi 5015C dialog box appears 4 Click the Device Set tab fi 5015C Properties General Events alain n ement Diagnosis Device Info J Deviceset About Page Counter Total Page Count ADF 100000 pages Total Page Count FB 707 pages Pad Pic
28. ads only the text and eliminates drops out the red frame If you do not wish to have any colors dropped out select None Reverse Colors of scanned images are reversed Setup IPC button You can configure settings for scanning with Image Processing Software Option 2 5 How to use the Scanner Driver Gamma tab Properties for Fujitsu fi 5015C on STI 0000 Main Layout More C Download Custom Gamma 2 Brightness Contrast Reset Default Cancel Download You can download and use any Gamma pattern Custom You can specify the numeric values of items such as Gamma Brightness trast SNOIIVH3dO YANNVOS OISVE About tab Displays the version number of ISIS driver Properties for Fujitsu fi 5015C on STI 0000 Main Layout More Gamm TAY AY 15015 Version 1 0 10602 10001 Fujitsu fi 5015C Copyright C 2006 EMC Corporation QuickDriver Version 1 0 10602 2001 ISIS is a registered trademark and QuickDriver is a trademark of EMC Corporation Copyright 1998 2006 EMC Corporation All Rights Reserved Default Cancel fi 5015C Image Scanner Operators Guide 35 2 6 36 Image Scanning Application This section explains about the bundled ScandAll PRO image scanning application which is used as an example to explain the procedures in this manual ScandAll PRO supports both TWAIN ISIS driv
29. al fittings with a soft dry cloth Accumulated dust might cause fire or electric shock Do not install the device in locations that has oil smoke steam humidity and dust Do not install the scanner in locations subject to oil smoke steam humidity and dust Doing so might cause a fire or electric shock Turn the scanner OFF if it is damaged If the scanner is damaged for any reason disconnect immediately the power plug in order to turn out the scanner Contact the store where you purchased the scanner a o not put liquids inside the scanner Do not insert or drop metal objects in to the scanner Do not scan wet documents or documents with paper clips or staples Do not splash or allow the scanner to get wet If foreign objects water small metal objects liquids etc get inside the scanner immediately turn off the scanner and disconnect the power plug from the power outlet then contact the store where you bought the scanner or the Maintenance Service Center Pay particular attention to this warning in households where there are small children o a o not touch the inside of the scanner unless necessary Do not take apart or modify the scanner The inside of the scanner contains high voltage components Touching these components might cause fire or electric shock a o not use the scanner if there is a strange odor If you detect excessive heat coming from the device or detect other problems
30. ator panel goes out but the green LED stays lit To return from the Power Save mode perform one of the following e Load the document on the ADF paper chute e Press any button on the operator panel The scanner will be turned OFF when pressing down the power button for at least two seconds e Execute a command from the scanner driver SNOIIVH3dO HHNNVOS OISVE fi 5015C Image Scanner Operator s Guide 11 2 2 Loading Documents on ADF This section explains how to check the document condition and load them on ADF These opera tions are very important to avoid paper jam or scanning error 2 2 1 Checking document condition Check that the document meets the following condition referring to Loading Document on Flatbed on page 17 If you scan sheets of paper that is not recommended for feeding with ADF a paper jam may occur in the scanner or a wrinkle may occur on a sheet To prevent this from occurring use Flatbed when scanning such paper ete documents do not meet the conditions scan them on Flatbed e B Document Size For ADF Minimum 115 Width x 140 Length mm 4 53 x 5 51 in Maximum 216 Width x 355 Length mm 8 5 x 14 in E Document Type The following paper types are recommended for ADF scanning e Woodfree paper Wood containing paper When using documents other than above paper types scan som test sheets of the same type to see if the documents can be scanned or not before at
31. attention to the following Cleaning If pick errors occur frequently clean the Pad ASSY For details on cleaning the Pad ASSY refer to 3 2 3 Cleaning the ADF on page 41 Replacing parts The service lives of the Pad ASSY and Pick roller ASSY are some times shortened when scanning medium grade paper documents e f paper containing wood is scanned the service life of the Pad and Pick roller may become shorter than that of the Pad and Pick roller used for scanning only woodfree paper e The pad or rollers of the scanner could be damaged if photographs or sheets of paper attached to the scanned document have contact with the pad or rollers during scanning e Scanning documents of calendered paper such as photographs may damage the surface of them fi 5015C Image Scanner Operator s Guide 13 2 SNOIIVH3dO YANNVOS OISVE When using the ADF the leading edge of all document sheets must be evenly aligned Make sure that curling at the leading edge is within the following tolerances Morethan smm Feed direction Less than 3mm Top of the paper Read surface Mere somm Feed direction Less than 5mm Top of the paper Read surface 2 2 Loading Documents on ADF 2 2 2 Loading documents on ADF This section explains how to load documents on ADF 1 Align the edges of the documents 1 Grasp no more than 50 sheets in a stack 2 Confirm that all the documents have the same width
32. click the Scan button on the dialog box 2 4 Scanning Documents gt The images of scanned documents are displayed on ScandAll PRO window ScandAll PRO My Documents image0001 tif 1 1 File Scan Edit Page Mark Zoom Tool Help a 8 0 ae 5 i eA E oF Om Ready 2 1 16 14 1 1 Pages mark For details on functions and operations of ScandAll PRO refer to description in Help menu gt gt Z Z m D O 0 m gt 2 p fi 5015C Image Scanner Operators Guide 21 2 5 Howto use the Scanner Driver E TWAIN Scanner Driver TWAIN Scanner Driver is designed for scanning documents with FUJITSU image scanner fi series by using application software that complies with the TWAIN standard The following describes the procedure with examples of ScandAll PRO for ordinary scanning by using this driver 1 Procedure for Basic Scanning Operation 1 Startup the application From the Start menu select All Programs Fujitsu ScandAll PRO and click ScandAll PRO 2 Select your scanner on the window below Select Select Source from the Scan menu ScandAll PRO My Documents ima File Edit View Page Mark Zoom Scan ScanSettings Ctr N Batch Scan Settings Ctrl B Select Scanner FUJITSU 6 5015 sipc FUJ
33. d white Halftone Documents are scanned through halftone process ing in black and white Grayscale Documents are scanned in gradations from black to white For this mode you can select 256 gradations or 4 bit 16 gradations Color Documents are scanned color mod For this mode you can select 24 bit Color 256 Color or 8 Color Scan button Starts scanning documents with the current settings Preview button Documents are scanned preliminarily before the actual scanning You can confirm the image of the documents in the preview window Close button Saves the current settings and closes this window Reset button Undoes change opetation Help button Opens the TWAIN Scanner Driver Help window The window also opens by press ing the F1 key About button Opens an information window about the TWAIN Scanner Driver s version 2 5 How to use the Scanner Driver Option button You can set up the details of optional functions on the window below Rotation Job Cache Generic Startup Filter Flip Side Rotation Cancel Help Rotation 2 Rotation Degree 0 0 degree x Automatic Size and Skew detection Disable gt Te Rotation tab Select this tab when setting image rotation Job Cache tab Select this tab when setting cache mode blank page skipping etc Generic tab Select this tab to change the unit displayed on the Setting Window for the TWAIN Scanner Driver
34. des the certifica tion of low power transmitters and the operation of certificated transmitters without a license Feeds rollers Rollers that feed documents through the ADF Filtering A correction method that improves the read quality of handwritten documents The read quality of images written in pencil or ball pointed pen depends on the reflective light characteristics of the specific ink or lead used Dropped pixels may produce outlines gaps or thin barely connected lines due to uneven optical density Filtering detects areas lighter than their surroundings and increases their density to improve image clarity Flat bed An input device of the scanner where documents are placed and scanned Generally used for scanning pages out of a book or paper that is out of the feeding specification of the ADF Also used to scan a small volume of documents by manual operation Flatbed An input device of the scanner where documents are placed and scanned Generally used for scanning pages out of a book or paper that is out of the feeding specification of the ADF Also used to scan a small volume of documents by manual operation Gamma A unit of changes of images brightness It is expressed as a function of the electric input power to devices scanner display etc and an image s brightness If the gamma rate is larger than 1 the brightness of an image increases and vice versa In order to adjust the brithtness of an image close to the orignal
35. e document to be scanned on Flatbed 6 Document stopper Prevents ejected documents from dropping off the scanners exit tray 7 Flatbed Used when the ADF is not appropriate to scan the document 8 Operator panel Turns on off the scanner starts scanning by Send to or Scan button or displays function number 1 1 Units 2 Flatbed 1 2 gt lt 2 m O TI U gt JJ Part Function 1 Document holding Holds the document on Flatbed pad 2 Document bed On which the document is set face down 3 Backside 1 2 3 4 Part Function 1 USB connector Connects USB cable to PC 2 ADF cable connector Connects the cable from ADF 3 DC inlet Connects the cable from AC adaptor 4 Main Power switch Turns the power ON or OFF to the scanner fi 5015C Image Scanner Operator s Guide 3 4 Side ADF side 1 Part Function 1 Shipping lock Locks the scanning head to prevent the scanner damaged when moving or transporting Unlocked Locked 1 2 Operator Panel 1 2 Operator Panel 1 a 5 Function Send to Scan Power z gt lt m O f 1 3 4 85 X JJ 0 Function 1 Function button Changes the function activated by Send to button 2 Function number Indicates the function number or error status Fo
36. e side Then press Power button on the operator Panel The scanner is turned ON and the green LED on the operator panel lights During the initialization the indication of the Function Number Display changes as follows gt 0 gt The indication 1 means operator panel scanner is in the ready status 2 Turning the Power Off Hold the power button down for at least two seconds Function Send to Scan Poy OO ATTENTION Be sure to turn off the Power button on the operation panel before turning off the main power switch If you turn off the main power switch without turning off the Power button first other USB devices connected with the USB2 0 hub may fail E About Power ON OFF Control You can select either the scanner to be turned on off with disable the Power button on the operator panel or alternately you would then power the scanner on off by connecting or dis connecting the power cable The procedure is as follows 1 Open Scanner s Properties 1 When turning on the power check that the scanner is connected to your PC Refer to 2 3 Connecting the Scanner your a PC in fi 5015C Getting Started on the Setup DVD ROM for information about connecting the scanner to your personal computer 2 1 Turning ON OFF the Scanner 2 Double click the Printer and Other Hardware icon on the Control panel of your PC amp Control Panel File Edit view Favorite
37. electing photograph mode makes brightness and contrast settings effective but pre vents the threshold from being set With photograph mode the darkness of image corre sponds to the black pixel density making it suitable in scanning images such as photographs having gradations Pick roller Roller s that picks the page from the batch of paper in the paper chute and feed it into the ADF Pick start time The period from the manual insertion of the document until picking starts after the docu ment passes the hopper empty sensor Pixel Picture Element The tiny dots that make up a scanned image Portrait Orientation of documents or images Documents images are set or displayed vertically Portrait orientation A document is transported and read with the long side parallel to the moving direction Resolution The measure of the details or grain of images displayed on a computer screen As a met ric of the resolution dpi is customarily used SCSI Small Computer System Interface An abbreviation for Small Computer System Interface SCSI is a standard for inter faces used to connect devices such as hard disks scanners etc Up to seven devices can be connected through this interface daisy chain The data transfer rates are differ ent between Fast SCSI Max 10MB sec and Wide SCSI Max 20MB sec SCSI ID Used to specify a particular SCSI device when the initiator selects a target or the target reconnects to the ini
38. error refer to the Operator s Guide 4 1 Error Indi cations in the Function Number Dis play page 54 for removing the alarm or the error Does the alarm state remain dis played even after the scanner has been turned off and back on again Turn off and on the power button If this does not eliminate the alarm state contact the store where you pur chased the scanner or an authorized FUJITSU scanner service provider Vertical lines appear in the generated image of the scanned image Is the glass dirty Clean the glass following the instruc tions in the Operator s Guide 3 Maintenance The generated image shifts or is distorted Quality of generated image is unsatisfac tory Are the documents loaded correctly Are the glass or sheet guides a white location clean Load the documents correctly Clean dirty locations 4 2 Troubleshooting Symptom Check this item Remedy Multi feed frequently occurs Does the document satisfy the Doc ument Quality described in Section 2 2 1 Scan the documents by Flatbed Are the documents set properly in the ADF paper chute Fan the documents before scanning Correctly align the document stack and load them on the ADF paper chute Refer to Section 2 2 2 for details Is the document stack thicker than 4mm Reduce the number of sheets in the document stack to 4 mm thickness or less Is the Pad
39. ers By defining scan settings as profiles you can customize the settings according to your preference Chapter 3 MAINTENANCE This chapter describes how to clear the paper jam perform daily maintenance and cleaning Z WARNING Do not use aerosol sprays near the scanner Do not use any aerosol sprays or alcohol based sprays to clean the scanner Dust blown up by strong air from the spray may enter the inside of the scanner This may cause the scanner to fail or malfunction Sparks caused by static electricity generated when blowing off dust and dirt from the outside of the scanner may cause a fire Be careful the inside of ADF automatic document Z CAUTION feeder may become hot during the operation 3 1 How to clear the paper jam sen 38 KE CIC AIG eere 39 3 3 Replacing 2 tease AI ARD n ERE ERI ALIE OE UTER KMS oS etude 44 fi 5015C Image Scanner Operator s Guide 37 3 1 How to clear the paper jam Be careful not to get injured when removing jammed AN CAUTION documents When a paper jam occurs while using ADF follow the procedure below to remove jammed paper 1 Remove the documents from the ADF paper chute 2 Open the ADF Be careful the ADF may close and pinch your fingers CAUTION 3 Remove the jammed paper ATTENTION Staples paper clips etc cause document jams Be sure to fully check the document and feed path and remove any small metal object
40. figuration Window of ISIS Scanner Driver 31 F oes ste e ette 3 Function number display 5 8 H How to use the Scanner Driver 22 ISIS Scanner Driver 28 L Loading Documents on the ADF for uses tie tedio atii o 12 Loading Documents on the Flatbed for SCANNING 17 P Paper jam ace nan 38 Paper layout ISIS 32 Paper Layout TWAIN 18 Paper Size ISIS 32 Paper Size TWAIN 18 20 25 Power save mode 11 R Remedying Common Troubles 56 Replacing the Pad ASSY 47 Replacing the Pick Roller 50 Reset the pad counter 48 Reset the Pick roller counter 52 Resolution TWAIN 25 S Scan button 5 Scan Type ISIS ete 32 Scan Type TWAIN 20 25 Scanner spacifications 1 Scanning Documents 19 Send to button 5 Setting Window for TWAIN Scanner Driver 25 Shipping lock Lans 4 Side guid tiep tinus
41. g to be used for a long period of time be sure to disconnect the power plug from the power outlet for safety Do install the scanner in the direct sunlight Do not install the scanner under direct sunlight or near heating apparatus Doing so might cause excessive heat to build up inside the scanner which can cause scanner trouble or even fire Install the scanner in a well ventilated location Before moving the scanner make sure the shipping lock is locked When moving the scanner be sure to lock the shipping lock in order to prevent damages to the scanner fi 5015C Image Scanner Operators Guide Xi xii Chapter 1 NAME OF PARTS This chapter shows the exterior view and the name of each part to descrive its function aieo derriere 2 1 2 Operator Panel is ciscciciscstivsisiveihicatencsdeincnstavenssveevicesisasvGeureusseuscdavenalcededelteciecaseleadeiess 5 fi 5015C Image Scanner Operator s Guide 1 1 1 Units 1 Front side 1 2 3 4 5 6 7 8 Part Function 1 Automatic docu Automatically feeds documents one by one to the reading position in the ment feeder ADF scanner 2 Side guides Holds the documents straight 3 ADF paper chute Holds the documents to be fed by the automatic document feeder ADF 4 Extension Extended when long documents are set 5 Document cover Stacks the documents after being scanned by ADF Holds th
42. gher resolution produces finer image but requires much more memory Halftone Selects the halftone pattern for halftone scanning This setting is available when Black amp White is selected in the Image Mode Dither Pattern 0 This setting is suitable for scanning dark photo graphs fi 5015C Image Scanner Operators Guide 31 Brightness Sets the brightness of the entire image Specify the brightness as a number within the range of 1 dark to 128 bright To brighten the entire image increase the value of the setting To darken the entire image decrease the value Contrast Sets the contrast between light and shadow of the scanned image Specify the contrast as a number within the range of 1 low soft to 100 high sharp Increasing this value makes the contrast sharper Paper Source Selects the scanning method Automatic Automatically switches the method between ADF scanning and flatbed scanning ADF Scans documents using the automatic document feeder ADF Flatbed Scans documents using the flatbed Layout tab Properties for Fujitsu fi 5015C on STI 0000 About Paper Size A4 210 297 mm Paper Layout Portrait Default Cancel Paper Size Selects a paper size according to the size of the document to be scanned Select a stan dard paper size from the list Paper Layout Specifies orientation of the documents as portrait or landscape 32 2 5 How
43. he Select button Select Scanner Device FUJITSU fi 5015C si 4 Select the Scan menu Scan Settings gt The Scan Settings dialog box appears 5 Click the Scanner Setting button gt The TWAIN Driver dialog box for setting the scan conditions appears fi 5015C Image Scanner Operator s Guide 19 2 SNOIIVH3dO YANNVOS OISVE 20 6 Set the scan type paper size see below etc and click the OK button 7 For details on settings in the TWAIN Driver dialog box refer to 2 5 How to use the Scan ner Driver on page 22 i TWAIN Driver 32 DE MR AS Ot Do mage Scanner EAMB Browse Setting Files 00 Current Setting v Config EM Select ADF or Flatbed Resolution can 300 x 300 ADF Front Side 21 ck Paper Size 297 mm Paper Size Er Enable Multi Image Front Pon Image Mode Brightness Black amp White vs EE Black White Threshold Static Threshold x 128 Scanning Areal inch Let 0000 0000 Contrast Width 8268 Length 11 593 i gt Advance Preview Reset Option Help About TWAIN driver Press F1 key to show help Data Size about 11MB You are returned to the Scan Settings dialog box Click the Scan button ote When you are using TWAIN you may see the TWAIN Driver setup dialog box again If so
44. i 5015C Properties dialog box appears fi 5015C Properties Diagnosis Devicelnfo About General Events Color Management gt f 5015C Manufactured by FUJITSU Scanner Status Status Device Ready On Port AUsbscan0 Optical resolution 600x600 DPI Diagnostics Cancel 5 Click the Device Set tab The following panel appears fi 5015C Properties General Events gement Diagnosis Device Info About Page Counter Total Page Count ADF 100000 pages Total Page Count FB 707 pages 20000 pages Pick Roller 100000 pages Power saving 7 15 minutes DK Cancel Apply 2 Click Power Control button The following screen is displayed Power Control Enable power switch Factory initial setting Disable power switch 10 2 1 Turning ON OFF the Scanner 3 In this screen e To power on off the scanner by pressing the Power button select Enable power switch To power on off the scanner by connecting or disconnecting the AC cable select Disable power switch E Power Save Mode 2 The Power Save mode keeps the scanner in a low powered state after it has been turned ON If no operation is performed on the scanner for 15 minutes the scanner automatically switches to the Power Save mode In the Power Save mode the indication of the Function Number display on the oper
45. k Roller Power saving p 15 minutes 5 After clicking the Clear button besides Pick roller in Page Counter click the OK button The following window appears Attention Click the OK button The Pick roller counter returns to 0 52 Chapter 4 TROUBLESHOOTING This chapter describes how to remedy troubles and items to check before contacting the agent where you bought the scanner 4 1 Error Indications in the Function Number 54 4 2 TroublesthioOlrig cerei ten ter Zu vs iu ER ndn 56 fi 5015C Image Scanner Operator s Guide 53 4 1 54 Error Indications in the Function Number Display When any error occurs the operator panel indicates U followed by a number alternately for tem porary errors or E followed by a number for device alarms permanent error Temporary errors can be resolved by the operator but the device alarm requires recovery works by support engineers When the Error Recovery Guide is installed on your PC and if any error or device alarm has occurred this software displays information such as error names and error codes regarding the error alarm Take notes of the information and click Details on its window to learn detailed infor mation for troubleshooting B Temporary Errors A number appearing in alternation following
46. l vents Do not allow moisture to get inside the device during cleaning E Cleaning Method 1 Open the document cover 2 Clean the following locations using a soft dry cloth moistened with cleaning fluid Document holding pad Wipe gently Document bed Wipe lightly ATTENTION e Be careful not to allow moisture to get inside the device during cleaning t may take long before the cleaner vaporizes if a large quantity is used When cleaning the scanner parts dampen a cloth with mod est quantities of the cleaner In addition wipe off the cleaner com pletely with a soft lint free cloth to leave no residue on the surface of the cleaned parts 3 Wait for cleaned parts to dry 4 Gently close the document cover 40 3 2 Cleaning 3 2 3 Cleaning the ADF Clean the ADF every 1 000 scans Note that this guideline varies according to the type of documents you are scanning For example it may be necessary to clean the ADF more frequently if documents are scanned when the toner is not sufficiently fixed on the printout As the documents are scanned by ADF Pad ASSY and Pick roller unit may be contaminated with ink toner particles or paper dust In this case the scanner may not feed documents smoothly or several documents may be fed at once If this occurs please clean the
47. ly the above specified consumables S ae Refer to Guidelines for Consumable Replacement Cycle on page 45 to find how many documents scanned by the consumable 44 3 3 Replacing Consumable 3 3 2 Guidelines for Consumable Replacement Cycle With this product you can learn how many times the consumables are used so that you can estimate the right timing for the replacement 1 When turning on the power check that the scanner is connected to your PC Refer to 2 3 Connecting the Scanner to your PC in fi 5015C Getting Started on the Setup DVD ROM for information about connecting the scanner to your personal computer 2 Double click the Printers and Other Hardware icon on the Control panel of your PC amp Control Panel File Edit View Favorites Tools Help Q search 5 Folders 25 CE x Er Address gt Control Panel Control Panel Pick a category B Switch to Classic view r Ro Appearance and Themes Printers and Other Hardware See Also 2 NUES gt The Printer and Other Hardware window appears 3 Onthe Printers and Other Hardware window double click the Scanners and Cameras icon Printers and Other Hardware File Edit View Favorites Tools Help Back o 2 yo Search 2 Folders 25 0 G e EN Address J Printers and Other Hardware SEEMS 28 Printers and Other Hardware Add Hardware E Display Pick a task Sounds Speech and i
48. nance of the high volume pro duction level scanner to reduce paper transport problems Note these sheets are not meant to replace the more thorough periodic cleaning of the scanner Color balance Balance of colors in images Default settings Pre set values for optional menus Density In this manual refers to a measurement of the depth of the display Dither The process by which a group of dots is arranged to represent a shade of gray The pre determined dot pattern simulates shades of gray This scanning process offers the advantage of reduce memory requirements compared to multilevel gray Document jam A warning that appears when document is jammed in the transport unit or transportation is interrupted because the paper is slipping dpi Dots per inch Number of dots lined along one inch A measurement of resolution nor mally used for scanners and printers Higher dpi means better resolution Driver software In this manual driver software refers to software that allows the scanning application software to communicate with the scanner Dropout color A color which is used in the document but does not appear in the read image Duplex reading mode A mode for scanning both sides of the document in one pass Eject rollers Rollers that transport documents from the ADF onto the Stacker Energy Star ENERGY STAR is an international standard for energy efficient electronic equipment It was created by the US Environment P
49. nd to 1 9 on the computer For example when you want to execute an event Send to 2 choose HINT 52 6 on function number display e Every time you press the Function button the number displayed will change in the order presented below 1 2 3 9 1 2 3 gt Simply pressing the Send to button starts the linked application fi 5015C Image Scanner Operator s Guide AP 5 AP 6 APPENDIX GLOSSARY OF TERMS A4 size A standard paper size Paper size is 210 x 297 mm 5 size A standard paper size Paper size is 148 x 210 mm A6 size A standard paper size Paper size is 105 x 148 mm A7 size A standard paper size Paper size is 74 x 105 mm A8 size A standard paper size Paper size is 53 x 74 mm ADF Automatic Document Feeder A unit that allows the user to scan a number of pages consecutively Fed documents are transported from the ADF paper chute or hopper to the Stacker Actual scanning opera tion is executed by the mechanism inside of this unit Backside reading Back side scanning Refers to reading the backside of the document specifically in Duplex reading mode Automatic separation An image processing method in which the scanner automatically detects difference between text and photos and chooses the threshold accordingly This function allows the scanner to switch between line mode and half tone mode in one pass fi 5015C Image Scanner Operators Guide AP 7
50. nu select Programs QuickScan and click QuickScan 2 Select your scanner on the window below Select Scan Select Scanner on the menu bar QuickScan Pro Demo CE po 1 Binary TIFF 2 Color JPEG 3 Select fi 5015C then click the OK button Scanner Selection Scanner Fuitsu 4750 Fujtsu fi 4750L Cancel Fuitsu 48 Setup Fujitsu fi 5220C 4 Select Scan New Batch on the menu bar 28 2 5 How to use the Scanner Driver 5 Select the profile for scanning New Batch 8 Select a Profile lt use preview settings gt Add Profile Binary TIFF Edit Profile Grayscale JPEG 24 bit color scanning saved as JPEG Path Je Documents and Settings furuse My Documents Browse File Name untitled jpg First Batch Next Page Custom Batch Cancel e When creating a new profile Select one from already existing profiles and click Add Profile button new profile will be created based on the profile you select e When changing the settings of already existing profiles Select one from already existing profiles and click Edit Profile button The settings of the selected profile can be changed e When using an existing profile Select the one from an already existing profiles The scanning will be started according to the settings of the selected profile Go to the procedure 9 6 Open
51. o Devices B view installed printers or fax printers Power Options System Add a printer Troubleshooters or pick a Control Panel icon 2 Hardware 2 Printing Ss Game Controllers lt gt Keyboard 2 Home or Small Office Networking Mouse 5 Phone and Modem Options 9 Printers and Faxes x Scanners and Cameras The Scanners and Cameras window is displayed 4 Right click the 5015 and select Properties from the menu for Windows XP double click for Windows 2000 gt Scanners and Cameras File Edit View Favorites Tools Help Qpak gt search Folders Imaging Tasks lt 5015 Add an imaninn devire fi 5015C Image Scanner Operator s Guide 45 JONVNALNIVN MESS gt The fi 5015C Properties dialog box appears fi 5015C Properties Diagnosis Device Info _ Device Set L About General Events Color Management fi 5015C Manufactured by FUJITSU Scanner Status Status Device Ready On Port Usbscan0 Optical resolution 600x600 DPI Diagnostics 5 Click the Device Set tab gt The following panel appears fi 5015C Properties General Events gement Diagnosis Device Info About Page Counter Total Page Count amp DF 100000 pages Total Page Count FB 707 pages Pad 20000 pages Pick Roller 100000 pages r Power saving M 15 minutes Power Control
52. o the AC adapter collectively viii Do not damage the AC cable A damaged AC cable may cause fire or electric shock Be careful of the following when handling the power cable Do not moisten modify tie bundle or wind the cable Do not place heavy objects on the cable trap the cable in a doorway drop or damage the cable in any other way Do not pull or forcibly bend or twist the cable Do not place any metal near to the plug of the power cable Do not use damaged AC cables or power plugs or install any cables or power plugs to loose wall sockets Use only specified AC cables and connector cables Use only specified AC cables and connector cables Failure to use the correct cables might cause electric shock and or equipment failure Please don t use the AC cable provided with this scanner for other devices since this might cause equipment failure and other troubles or an electric shock Use this scanner only at the indicated power voltage Do not connect to multiple power strips Use this scanner only at the indicated power voltage and current Improper power voltage and current might cause fire or electric shock Do not connect to multiple power strips gt Do not touch the AC cable with wet hands Do not touch the power plug with wet hands Doing so might cause electric shock gt Wipe any dust from the power plug Wipe off any dust from the power cable metal parts on the power plug or met
53. on Program Interface or protocol for imaging devices ners digital cameras etc developed by Pixel Translations a division of Captiva Soft ware In order to use imaging devices designed on the ISIS standard it is necessary to install the driver software of the same standard Jaggy images Images that have sharp projections or irregular shape on their edges Job separation sheet A sheet inserted between documents in a batch for separating different jobs Landscape A document is transported and read with the short side parallel to the moving direction Landscape orientation A document is transported and scanned with the long side vertical to the moving direc tion Letter size A standard paper size used in the U S A and other countries Paper size is 8 1 2 x 11 inches Linedrawing mode Selecting linedrawing mode makes threshold and contrast settings effective but prevents brightness from being set The specified threshold value determines whether black or white pixels are scanned Line drawing mode is therefore appropriate for scanning text and line art images Multi Feed detection A scanner function which detects accidental feeding of multiple sheets into the ADF This can be set as both enabled disabled Mirror image The read image is symmetrically flipped to produce a mirror image of the original detected in the main scanning direction Moire Patterns Recurrent patterns on scanned images caused by incorrect set
54. ppareil num rique de la classe B est conforme la norme NMB 003 du Canada Bescheimigung des Herstellers Importeurs F r den fi 5015C wid folgendes bescheinigt bereinsstimmung mit den Bestimmungen der EN45014 CE funkentst rt eMaschinenl rminformationsverordnung 3 GPSGV Der h chste Schalldruckpegel betr gt 70 dB A oder weniger gem EN ISO 7779 ENERGY STAR PFU Limited a Fujitsu company has determined that this product meets the ENERGY STAR guidelines for energy efficiency ENERGY STAR is a registered trademark of the United States ENERGY STAR liNote Liability READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT IF THIS PRODUCT IS NOT USED CORRECTLY UNEXPECTED INJURY MAY BE CAUSED TO USERS OR BYSTANDERS Also keep this manual in a safe place so that it can be easily referred to during use of this product While all efforts have been made to ensure the accuracy of all information in this manual PFU assumes no liability to any party for any damage caused by errors or omissions or by statements of any kind in this manual its updates or supplements whether such errors are omissions or statements resulting from negligence accidents or any other cause PFU further assumes no liability arising from the application or use of any product or system described herein nor any liability for incidental or consequential damages arising from the use of this manual PFU disclaims all warranties regarding
55. r detail refer 4 1Error display Indications in the Function Number Display on page 54 3 Send to button Launches an application software which is linked by the value of Function number display 4 Scan button Launches an application software linked 5 Power LED Lights when the scanner is turned on 6 Power button Turns the scanner ON or OFF fi 5015C Image Scanner Operator s Guide 5 Chapter 2 BASIC SCANNER OPERATIONS This chapter describes how to turn On Off the scanner and how to load scan the documents In this chapter Windows XP screenshots are illustrated The screens and operations may differ slightly if the OS you are using is not Windows XP Also when TWAIN is updated the screens and operations noted in this chapter will differ slightly 2 1 Turning ON OFF the Cod Eod xe EX eui SEE eX FL Vk sa avra dr aaa dE 8 2 2 Loading Documents on ADF 12 2 3 Loading Document on 17 2 4 Scanning Documents cecus ca cessas Rasen anne Raus Fa guide EE ERR ee 19 2 5 How to use the Scanner 22 2 6 Image Scanning Application 36 fi 5015C Image Scanner Operator s Guide 7 2 1 Turning ON OFF the Scanner 1 Turning the Power Switch on the Main Power switch located on th
56. r lamps eDo not incinerate crush or shred the lamps or scanner parts Trademarks Microsoft Windows Windows Server and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries ISIS and Quick Scan are either registered trademarks or trademarks of EMC Corporation in the United States Adobe the Adobe logo Acrobat and Adobe Reader are either registered trademarks or trade names of Adobe Systems Incorporated in the United States and or other countries Other company names and product names are the registered trademarks or trademarks of the respective companies fi 5015C Image Scanner Operator s Guide V How Trademarks Are Indicated In This Manual References to operating systems OS are indicated as follows Windows 2000 Windows 2000 Professional operating system Windows XP Windows XP Home Edition operating system Windows XP Professional operating system 32 64 bit Windows Server Windows Server 2003 Standard Edition 32 64 bit 2003 Windows Server 2003 R2 Standard Edition 32 64 bit Windows Vista Windows Vista Home Basic operating system 32 64 bit Windows Vista Home Premium operating system 32 64 bit Windows Vista Business operating system 32 64 bit Windows Vista Enterprise operating system 32 64 bit Windows Vista ultimate operating system 32 64 bit Windows Server Windows Server 2008 Standard 32 64 bit 2008
57. refer to 2 4 Scanning Documents on page 19 2 3 Loading Document on Flatbed 2 3 Loading Document on Flatbed Do not look directly at the light source during the scan AN CAUTION ning operation 1 Open the document cover 2 2 Place the document the document bed glass with face down 3 Position the document so that the upper left corner of the document is aligned with the reference mark of the document bed 4 Close the document cover gently 5 Scan the document SNOIIVH3dO YANNVOS OISVE For how to scan the document refer to 2 4 Scanning Documents on page 19 ATTENTION Do not move the document during scanning e Do not press or open the document cover during scanning E Scanning Thick Documents with Flatbed When scanning a thick document such as a book please remember the following notes 1 The document cover can be pulled out upwards 2 The not seated part of the document is not scanned correctly fi 5015C Image Scanner Operator s Guide 17 B Document Size For Flatbed Minimum 26 Width x 26 Length mm 1x 1 in Maximum 216 Width x 297 Length mm 8 5 x 11 7 in Orientation of the document and how to set Paper size shall be as follows for Portrait scan ning or Landscape scanning Portrait Landscape 55 e Paper Size setting e
58. rotection Agency EPA in 1992 The standard pro gram has now been adopted by several countries around the world fi 5015C Image Scanner Operator s Guide AP 9 AP 10 Equipment Error An error that cannot be fixed by the operator The operator should call the manufacturer for service Error diffusion High quality halftone pseudo grayscale image production based on black and white pixel binarization A pixel s optical density and that of adjacent pixels are summed with black pixels relocated in their order of density as they relate to adjacent pixels The pur pose of this technique is to minimize the average error between read and printed densi ties Density data for adjacent pixels is modified by diffusing errors on the objective pixel into several pixels which are then binarized This maintains high grayscale levels and resolution during reading while suppressing more patterns by dotted halftone images such as newspaper photographs FCC Acronym for The Federal Communications Commission an independent United States government agency which is in charge of regulating interstate and international commu nications via radio television wire satellite and cable The Part 15 of the FCC regula tions mentioned in this manual is designed to prevent harmful interferences on radio communication of radio receivers and other devices which radiate radio frequency energy and provides for the certification of radio receivers It also provi
59. s Tools Help OQ O 6 E roes 5 e X 19 Er Address e Control Panel VA Control Panel A Pick category um Appearance and Themes 1 Printers and Other Hardware See Also Windows Update 2 The Printer and Other Hardware window appears 3 On the Printers and Other Hardware window double click the Scanners and Cameras icon Printers and Other Hardware File Edit View Favorites Tools Help Qe search 2 Folders la 2 x EN Address p Printers and Other Hardware Printers and Other Hardware See Also Add Hardware amp Display Pick a task Sounds Speech and Audio Devices 23 view installed printers or fax printers Power Options BJ 49 System Add a printer Troubleshooters or pick a Control Panel icon 2 Hardware 2 Printing J Game Controllers lt gt Keyboard 2 Home or Small Office Networking SNOIIVH3dO YANNVOS OISVE Mouse 5 Phone and Modem Options Printers and Faxes gt Scanners and Cameras gt The Scanners and Cameras window is displayed 4 Right click the fi 5015C and select Properties from the menu for Windows XP or double click for Windows 2000 Scanners and Cameras File Edit View Favorites Tools Help D search Folders gt fi 5015C Imaging Tasks Add an imaging device fi 5015C Image Scanner Operator s Guide 9 The f
60. s such as these Also before you start scanning be sure to remove any staples clips etc from the document 4 Close the ADF completely until it clicks 38 3 2 Cleaning 3 2 Cleaning To keep scanner performance stable clean the scanner and replace the consumable if necessary as follows Be careful the inside of ADF automatic document ZN CAUTION feeder may become hot during the operation 3 2 1 Cleaning Materials Cleaning Materials Parts Number Remarks Cleaner F1 PA03950 0352 1 bottle 1 Moisten a cloth with this fluid and wipe the scanner clean Cleaning Wipe PA03950 0419 24 sheets pack 2 Lint free dry cloth Commercially available one For details about the cleaning materials contact the FUJITSU scanner dealer where you pur chased the scanner 1 It may take long before the cleaner vaporizes if a large quantity is used When cleaning the scanner parts dampen a cloth with modest quantities of the cleaner In addition wipe off the cleaner completely with a soft lint free cloth to leave no residue on the surface of the cleaned parts 2 Pre moistened with Cleaner F1 Cleaning Wipes are used instead of moistened cloths fi 5015C Image Scanner Operators Guide 39 JONVNALNIVN MESS 3 2 2 Cleaning the Flatbed ATTENTION e Detergent for cleaning windows or glass cleaner can be used instead of cleaning fluid However do not use paint thinner or other organic so
61. tempting to scan the documents E Document Thickness Paper thickness is generally expressed by paper weight The following shows the paper weights that can be used on this scanner 52 g m to 127 g m 141b to 341b Precautions The following documents may not be scanned successfully e Documents of non uniform thickness e g envelopes and documents with photographs attached Wrinkled or curled documents Refer to HINTs on the next page Folded or torn documents Tracing paper Coated paper Carbon paper Carbonless paper Photosensitive paper Perforated or punched documents 12 2 2 Loading Documents on ADF e Documents that are not square or rectangular Very thin documents e Photographs Do not use the following documents Paper clipped or stapled documents Documents on which the ink is still wet e Documents other than paper such as fabric metal foil or transparencies ete e When scanning semi transparent documents slide the Brightness bar 6 to light to avoid bleed through e To prevent the rollers from becoming dirty avoid scanning documents containing large areas written or filled in pencil If scanning of such doc uments is unavoidable clean the rollers frequently ATTENTION e Carbonless paper contains chemical substances that may damage the SU Pad ASSY or rollers e g Pick roller when these types of documents are fed Pay
62. the U refers to the following type of errors Indication Meaning Solution UO Shipping lock error occurred Confirm that the shipping lock is released UI A paper feed error occurred 1 Remove the jammed documents Refer to 3 1 How to clear the paper jam on page 38 2 Confirm that the documents meet the paper conditions for scanning Refer to 2 2 1 Checking document condi tion on page 12 U9 ADF error Turn OFF the scanner power Confirm Connect the ADF cable then turn on the scanner power ete The Error Recover Guide is stored in Setup DVD ROM For installing the application software refer to 2 1 Installing the Scanner Application in fi 5015C Getting Started 4 1 Error Indications in the Function Number Display B Device alarms A number appearing in alternation following the E refers to the following type of device alarms Indication Meaning Solution EO Shipping lock error occurred Confirm that the shipping lock is released Flatbed motor malfunction When you encounter any alarm turn mmm ical off and on the scanner If the alarm is E Trouble in the optical system still displayed on the Function Num E7 Trouble occurred in the internal ber Display contact the dealer where memory EEPROM you purchased the scanner or an authorized FUJITSU scanner service Eb A LSI error provider Ec An error in the memory Ed An error with USB chip
63. the information contained herein whether expressed implied or statutory Use in High safety Applications This product has been designed and manufactured on the assumption that it will be used in office personal domestic regular industrial and general purpose applications It has not been designed and manufactured for use in applications simply called high safety applications from here on that directly involve danger to life and health when a high degree of safety is required for example in the control of nuclear reactions at nuclear power facilities automatic flight control of aircraft air traffic control operation control in mass transport systems medical equipment for sustaining life and missile firing control in weapons systems and when provisionally the safety in question 1s not ensured The user should use this product with adopting measures for ensuring safety in such high safety applications PFU LIMITED assumes no liability whatsoever for damages arising from use of this product by the user in high safety applications and for any claims or compensation for damages by the user or a third party About the use of mercury Lamp s inside this product contain mercury and must be recycled or disposed of according to local state or federal laws To avoid unexpected injuries not put the substance contained in the lamp in your mouth as it has mercury not breathe the chemical liquid contained in the scanne
64. tiator Separation roller A roller that separates the sheets of paper from each other Simplex reading mode A mode for scanning only the front side of the document Smoothing A process that eliminates jaggies from slanted lines and curves Irregular convexities are deleted and irregular concavities filled in This is useful in OCR applications for example Storage temperature humidity The temperature and humidity levels necessary for proper storage of the scanner Temporary Error An error that can be fixed by the operator Terminator Devices with a SCSI interface can be daisy chained A resistor that includes terminal cir cuits needs to be placed at both ends of the SCSI chain when devices are daisy chained If a device such as a scanner is the last device in a chain leaving an interface connector unused a Terminator therefore must be attached to provide those terminal cir cits Third Party Interface Used to install optional board provided by Fujitsu or interface board manufactured by a third party Threshold A value used as a metric for judging a color as black or white For scanning an image with gray gradation this value must be defined The threshold setting determines which pixels are converted to black and which will become white TUV An institution that controls products for conformity with various standars of security usability and environmental matters fi 5015C Image Scanner Operator s Guide
65. tings of angles Noise removal Isolated noise from an image appearing as black spots in white areas and voids in black areas is removed to improve image quality Removes particles from the document image Common particles include toner and fax particles Noise reduction works via an algorithm that removes pixels up to 5 x 5 dots appart A dot is 1 400 inch A particle can be distinguished from a character as it is not connected to another dot within 5 pixels OCR optical character recognition Devices or technologies for identifying characters on documents and converting them into text data that can be manipulated The documents are checked by light and the dif ferences of light reflection are recognized as character shapes Operator panel A panel consists of indicators and buttons The operator panel is used to control scanner operations such as selecting features and changing settings Optical sensor A type of sensor for detecting Multi Feeding by light transmission It also detects multi feeding by recognizing differences in length of documents Outline extraction The boundary between black and white areas is traced and the outline extracted for closed areas Pad ASSY Pad Assembly This part is used to separate a sheet of paper from a batch before feeding documents into the ADF This assembly is made out of rubber fi 5015C Image Scanner Operator s Guide AP 13 AP 14 Photograph mode White level follower OFF S
66. to use the Scanner Driver Scan Area button Opens the Scan Area dialog box Specify scan area for the document size The size can be set by dragging the frame with mouse Otherwise enter any value for the setting Scan Area Page Size 4 210 x 297 mm Paper Layout Portrait Landscape 2 Area x o Pixels x jo Inches Width 226772 Centimeters Height f 1 5829 v Snap SNOIIVH3dO HHNNVOS OISVE fi 5015C Image Scanner Operators Guide 33 34 More tab Opens More Settings window Used for setting advanced features Properties for Fujitsu fi 5015C on STI 0000 Overscan Color Dropout Green Reverse Default Use Advanced DTC This option scans any kind of documents by binary processing to produce data with good scanning quality Documents containing thin letters characters with the colored background and colored charts cannot be scanned sufficiently clearly by ordinary binary processing By using this option however you can achieve good scanning qual ity Overscan Specifies the overscan function which makes the scanned images larger than the original documents by adding margins Color Dropout Excludes selected color the three primary colors of light i e green red blue from scanned images For example if the document contains black text in a red frame and when the red color is selected the scanner re
67. ton v Actions 7 ScandAll PRO Prompt for which program to run O Take no action The events available for this function are Scan Button When pressing the Scan button Send to 1 9 When pressing the Send to button fi 5015C Image Scanner Operators Guide AP 3 4 Select the application with its process excuted by the event For the case of Windows XP click Start this program under Actions and select the application and process from the menu fi 5015C Properties Diagnosis Device Info Device Set About General Events Color Management Choose event below then select the action to take when that 9 event occurs Select an event ci Scan Button Actions Prompt for which program to run O no action Click the OK button If you are using PRO refer to ScandAll PRO V2 0 User s Guide ete The window and operations may vary depending on your OS Settings on the Scanner Function number display Function Send to Scan Power QQ Function button Send to button Scan button e Touse the SCAN button You can use this button as is no special settings are required gt Simply pressing the SCAN button starts the linked application e To use the Send to button Press the Function button to change the number on the function number display Choose the same number as an event number you selected Se

Fujitsu FI-5015C Photo Scanner User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents