Fujitsu B17-3 Computer Monitor User Manual
Contents
1. A26361 K1143 2120 1 7619 edition 3 1 SCENICVIEW B17 3 B19 3 P19 3 Notational conventions The meanings of the symbols and fonts used in this manual are as follows Pay particular attention to text marked with this symbol Failure to observe this warning endangers your life destroys the device or may lead to loss of data lil Supplementarv information remarks and tips follow this svmbol gt Text which follows this symbol describes activities that must be performed in the order shown Quotation marks indicate names of chapters or terms This font indicates filenames and menu items This font indicates screen outputs Important notes In this chapter vou will find information regarding safetv which is essential to take note of with vour monitor Safetv notes This device complies with the relevant safetv regulations for data processing equipment including electronic office machines for use in an office environment If you have any questions contact your sales outlet or our help desk Q The display surface of the LCD monitor is sensitive to pressure and scratches You should therefore be careful with the displav surface so as to avoid lasting damage scratches e If the device is brought into the installation site from a cold environment condensation can form Before operating the device wait until it is absolutely dry and has reached approximately the same temperature as the installation site Q During installing2. Adjust a different screen resolution using the computer software see documentation for your computer or your screen controller Picture position not correct The monitor recognises an undefined mode see the Technical data chapter gt Press the EXIT AUTO button to perform the auto adjustment of the screen Picture is shaking gt Check whether the data cable for the monitor is correctly attached to the monitor port on the computer gt Press the EXIT AUTO button to perform the auto adjustment of the screen 24 A26361 K1143 2120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P19 3 Having this problem Check the following points Picture is wronglv adjusted gt Press the SELECT MENU button to activate the function Factory Recall The Auto Processing message is displayed Picture disturbances vertical lines gt Press the EXIT AUTO button to perform the auto adjustment of the screen picture noise Picture disturbances horizontal lines gt Press the EXIT AUTO button to perform the auto adjustment of the screen The screen becomes darker The background lighting has a limited lifetime If your monitor display should become too dark the background lighting will have to be exchanged gt Please contact our help desk A26361 K1143 2120 1 7619 edition 3 25 SCENICVIEW B17 3 B19 3 P19 3 Notes regarding the DIN EN ISO 1
3. 3 Contents A26361 K1143 2120 1 7619 edition 3 Introduction Your new LCD Liquid Crystal Display monitor SCENICVIEW B17 3 B19 3 P19 3 offers numerous features and functions for example TFT display Thin Film Transistor active matrix minimal space requirements thanks to slim casing e optimum ergonomic characteristics totallv distortion free excellent picture definition and colour purity right into the corners high degree of brightness and good contrast high resolution 1280 x 1024 presentation of up to 16 7 million colours in conjunction with an appropriate graphics card automatic scanning of horizontal frequencies from 30 to 82 kHz and refresh rates vertical frequencies from 56 to 76 Hz absolutely flicker free Q digital screen controller with microprocessor for storing 26 different displav modes e freelv adjustable colour alignment for matching the screen colours to the colours of various input and output devices Q convenient operation via integrated OSD On Screen displav menu e VESA DDC compatibilitv e VESA FPMPMI compatibilitv Flat Panel Monitor Phvsical Mounting Interface Mounting device for swivel arm and wall bracket e plug amp play capabilitv Q power management for reducing power consumption when the computer is not in use Q compliance with the recommendations in accordance with TCO 03 Q The monitor fulfils all GS Gepr fte Sicherheit Certified Security requirements This operati
4. Phone No 408 834 0306 Fax No 408 746 8299 We Fujitsu Siemens Computers Inc hereby declare that the equipment bearing the trade name and model number specified above was tested confirming to the applicable FCC Rules under the most accurate measurement standards possible and that all the necessary steps have been taken and are in force to assure that production units of the same equipment will continue to comply with the Commissions requirements A26361 K1143 2120 1 7619 edition 3 5 SCENICVIEW B17 3 B19 3 P19 3 Energy Star Guidelines MAIL The Fujitsu Siemens LCD monitor SCENICVIEW B17 3 B19 3 P19 3 is designed to conserve electricitv bv dropping to less than 1 W when it goes into standbv suspend and OFF mode With this new power management the LCD monitor SCENICVIEW B17 3 B19 3 P19 3 qualifies for the U S Environmental Protection Agency s EPA Energy Star Computers award The EPA estimates that computer equipment uses 5 90 percent of all business electricitv and that this is growing rapidly If all desktop computers and peripherals enter a low power mode when not in use the overall savings in electricity could amount to 2 thousand million annually These savings could also prevent the emission of 20 million tons of carbon dioxide into the atmosphere the equivalent of 5 million automobiles As an Energy Star Partner Fujitsu Siemens Computers GmbH has determined that this product meets the Energy Star guid
5. Position with this function you move the OSD menu to the left or to the right OSD Setting the vertical position of the OSD menu V Position with this function you move the OSD menu up or down OSD Setting the display duration of the OSD menu Timeout With this function you select a value from 10 to 120 seconds Ifthe set time expires without a setting being made the OSD menu is automatically faded out OSD Setting the display format of the OSD menu Rotation With this function you switch the OSD menu from portrait mode to landscape mode and vice versa Off The OSD menu is displayed in portrait mode On The OSD menu is displayed in landscape mode Setting functions in the Advanced menu Calling the Advanced setting window iY Input select Selecting input signal With this function you switch the monitor from the analogue to the digital mode and vice versa when two signal sources are connected The condition is that the graphic card used supports this function DDC CI Activate deactivate DDC CI function On the DDC CI function is activated default setting Off the DDC CI function is deactivated Resolution Displaving monitor data Notifier The optimum resolution for this monitor is 1280 x 1024 pixels With the function activated On a message appears on the screen after approx 30 seconds if a different resolution is set Change the resolution to 1280 x 1024 to achieve optimum picture qualitv With the
6. Proceed according to the four steps in the illustrations to fold out the monitor base 10 A26361 K1143 2120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P19 3 Removing monitor base Before vou can use a swivel arm or a wall bracket vou must remove the monitor base N The display surface is susceptible to scratching gt Switch off the monitor and pull the power plug out of the power socket gt Lay the monitor on its face on a soft surface gt Remove the cover and disconnect all cables gt Remove the four screws on the rear of the monitor You can now mount a swivel arm or a wall bracket as per VESA FPMPMI with 100 mm hole spacing For instructions on how to mount the swivel arm or wall bracket please see the documentation for the swivel arm or wall bracket If you operate the monitor with the swivel arm or wall bracket it may not be turned by 180 A26361 K1143 2120 1 7619 edition 3 11 SCENICVIEW B17 3 B19 3 P19 3 Connecting the monitor N Please take note of the safety information in the Important notes chapter CE conformance and optimum picture quality are guaranteed only if you use the data cables supplied Do not cover the ventilation openings of the monitor The computer power plug must be pulled out gt Be sure that the monitor and the computer are switched off 12 A26361 K1143 2120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P19 3 Connecting cables to the monitor
7. function deactivated Off no message appears Factory Recall Activating the factory settings With this function all settings are reset to the factory settings without prompting for confirmation Press the SELECT MENU button to activate the function The Auto Processing message is displayed 22 A26361 K1143 2120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P19 3 Displaving information Calling the Information setting window With this function the model designation serial number resolution H V frequency input signal and polarity of the synchronisation signal are displayed Notes on ergonomic colour adjustment If you select colours for the display in your application programmes take note of the information below The primary colours blue and red on a dark background do not produce the minimum required contrast of 3 1 and are therefore not suitable for continuous text and data entry When using several colours for characters and background and giving the primary colours full modulation you can obtain very suitable colour combinations see the following table Characters Colour combination very suitable Colour combination not suitable because colour locations are too close together thin characters are not identifiable or rigorous focusing is demanded of the human eye A26361 K1143 2120 1 7619 edition 3 23 SCENICVIEW B17 3 B19 3 P19 3 Troubleshooting Should an error occur first check the followi
8. to change other settings select the corresponding function from the OSD main menu All possible adjustments of the main menu are described in the following operation some functions are not available as they are not required due to the digital lil The OSD menu for analogue monitor operation is described in the following During digital transmission technologv used Adjusting the brightness and contrast Calling the Brightness Contrast setting window Brightness Setting the brightness of the display With this function you change the brightness of the background lighting Contrast Setting the contrast of the display With this function you modify the contrast of bright colour tones Black Level Setting the brightness of the display With this function you modify the contrast of dark colour tones Auto Level Setting the brightness of the display With this function you can automatically set the contrast Press the SELECT MENU button to activate the function If the contrast is set too high bright surfaces can no longer be distinguished from very bright surfaces If the contrast is set too low the maximum brightness will not be achieved 20 A26361 K1143 Z120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P19 3 Adjusting size and position 5 Calling the Image adjust setting window H Position Adjusting the horizontal position With this function you move the picture to the left or to the right V Position Adjusting the ver
9. 3406 2 standard Permanentiv unlit or lit pixels The standard of production techniques todav cannot guarantee an absolutelv fault free screen displav A few isolated constant lit or unlit pixels picture elements mav be present The maximum permitted number of pixels faults is stipulated in the stringent international standard ISO 13406 2 Class II Examples A 17 or 19 flat screen monitor with a resolution of 1280 x 1024 has 1280 x 1024 1310720 pixels Each pixel consists of three subpixels red green and blue so there are almost 4 million subpixels in total In accordance with ISO 13406 2 Class II a maximum of 6 pixels and 7 subpixels may be faulty Pixel A pixel consists of 3 subpixels normally red green and blue A pixel is the smallest element that can be generated by complete functionality of the display Subpixel A subpixel is a separately addressable internal structure within a pixel that enhances the pixel function Cluster A cluster contains two or more defective pixels or subpixels ina5x5 pixel block 26 A26361 K1143 2120 1 7619 edition 3 Technical data Dimensions and weight Visible diagonals Dot pitch Screen size Width Height Maximal resolution Dimensions incl Width monitor base Height Box dimensions Depth Width Height Depth Weight without packaging Storable display modes Pixel error classes according to ISO 13406 2 Accessories Electrical data Video Synch
10. 61 K1143 2120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P19 3 Checking the contents of the consignment The displav surface of the LCD monitor is sensitive to pressure and scratches Alwavs hold the device by the casing gt Unpack all the individual parts gt Check the delivery for damage incurred during transportation gt Check whether the delivery agrees with the details in the delivery note The complete LCD monitor package includes one monitor one data cable D SUB one data cable DVI D one audio cable one power cable one CD with software and documentation one Warranty Booklet one Getting Started manual Should you discover that the delivery does not correspond to the delivery note notify your local sales outlet immediately We recommend that you keep the original packaging material Keep it for future transportation A26361 K1143 2120 1 7619 edition 3 7 SCENICVIEW B17 3 B19 3 P19 3 Installing an ergonomic video workstation peal gt INA Zi gt Man Ban ST I gt N L y ea Ea i jiko GIE gt et A il 1 Windows Avoid glare from electric 1 Edge of desk Avoid direct and reflected glare lighting 2 Permissible reaching sector Position the keyboard where it is easiest to reach 30 cm 1 Bearing surface for palms of hands 2 Reaching area for frequently used equipment Position
11. D menu perform the following steps gt Press the SELECT MENU button to activate the OSD menu The main menu appears on the screen on the left hand side with icons for the setting functions The first symbol Brightness Contrast is 0 highlighted In the right hand part of the displav Brightness Contrast nl e the associated functions are shown gt f necessary press the w or a button to Image adjust Brightness mark another icon e g Image adjust nf Samen gt Press the SELECT MENU button to select Audio Black Level the highlighted icon Auto Level Colour E OSD Setup Advanced Information A26361 K1143 2120 1 7619 edition 3 19 SCENICVIEW B17 3 B19 3 P19 3 The corresponding setting window here Image Adjust is displaved on the right hand side The first function H Position is highlighted co XO FUJITSU coueurers gt If necessary press the w or a button to BrightnessiContrast SIEMENS mark another function Es Fr gt Press the SELECT MENU button to select Image adjust en the highlighted function a Clock gt Press the w or a button to adjust the EN Ra value for the selected function Colour gt Press the EXIT AUTO button to exit the function OSD Setup gt f necessary press the button w or a to r mark another function or press the Advanced 50 ee button to return to the main u Information All changes are stored automatically If you want
12. Monitor English Operating Manual SCENICVIEW B17 3 B19 3 P 19 3 OOC fee FU ITSU COMPUTERS We make sure ee Are there any technical problems or other questions which you would like to be clarified Please contact our help desk see Warrantv Booklet The latest information on our products tips updates etc can be found on the internet under http www fujitsu siemens com This manual was produced bv Xerox Global Services Published bv Fujitsu Siemens Computers GmbH Order No A26361 K1143 Z120 1 7619 Edition 3 AG 08 07 SCENICVIEW B17 3 B19 3 P19 3 LCD monitor Operating Manual august 2007 edition VESA DDC and DPMS are registered trademarks of Video Electronics Standards Association Copyright Fujitsu Siemens Computers GmbH 2007 All rights including rights of translation reproduction by printing copying or similar methods in part or in whole are reserved Offenders will be liable for damages All rights including rights created by patent grant or registration of a utility model or design are reserved Delivery subject to availability Right of technical modification reserved No liability for content and printing error Contents Introduction m 2 a nn nr ee S AA A Notational conventions Important notes 22 20 Sane in eas lag cel hau inal ih isa d iaa Safety NOleSex set nasi Kran ann ieee AT Rein Bien ieee eet Power cable Transport C
13. The monitor ports are protected bv a cover gt Remove the cover 1 Power connector 2 DVI D connection socket DIGITAL 3 D SUB connection socket ANALOG 4 Security slot for Kensington Lock 5 AUDIO IN connector 6 Cover position 7 Holes for fixing swivel arm or wall bracket The data cables supplied have two 15 pin D SUB connectors two 24 pin DVI connectors for connection to the monitor and to the computer gt gt Select the suitable data cable for your computer Digital graphics card with DVI interface DVI connector Graphics card with VGA interface D SUB connector Information on the computer connections and interfaces is contained in the operating manual for your computer Connect one of the connectors of the data cable to the D SUB connector 3 or the DVI D connector 2 on the monitor and secure the plug in connection by tightening the safety screws li The monitor automatically detects the input when only one signal source is connected gt gt Insert one plug of the audio line in the AUDIO IN 5 socket on the monitor and make sure it is properly engaged Plug the power cable supplied into the power connector 1 of the monitor Mount the cover over the connections from theft A Kensington Lock is not included in the consignment of the monitor lil A lock Kensington Lock can be mounted in the securitv slot 4 to protec
14. and operating the device please observe the instructions on environmental conditions in the Technical data chapter as well as the instructions in the Installing an ergonomic video workstation chapter 2 A26361 K1143 2120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P19 3 Q To ensure sufficient ventilation the intake and exhaust air openings of the monitor must never be blocked e The monitor automaticallv sets itself to a mains voltage in the range of 100 V to 240 V Ensure that the local mains voltage lies within these limits Q Ensure that the power socket on the device or the grounded mains outlet is freely accessible Q The ON OFF switch does not disconnect the device from the mains voltage To completelv disconnect the mains voltage remove the power plug from the socket e The monitor is equipped with a power cable that complies with safetv standards e Lav all cables so that nobodv can stand on them or trip over them When attaching the device observe the relevant notes in the Connecting the monitor chapter e No data transfer cables should be connected or disconnected during a thunderstorm Q Make sure that no objects e g jewellerv chains paper clips etc or liquids get inside the device danger of electric shock short circuit Q The device is not waterproofl Never immerse the device in water and protect it from sprav water rain sea water Q In emergencies e g damaged casing elements or cables penetration
15. compatible VGA interface it can automatically read the data for ensuring optimum operation from your monitor and select the appropriate settings monitors you can select the following monitor instead lil If the monitor SCENICVIEW B17 3 B19 3 P19 3 is not vet displaved in the list of Fujitsu Siemens P17 2 P19 2 B17 2 B19 2 Preset operating modes The picture position and size have been set to optimum values at the factorv for the operating modes listed above Depending on the screen controller used it mav be necessary to adjust the display position and size In this case you can change and save the settings see Operation of the monitor The following are the most frequentiv used of the preset operating modes Horizontal frequency Refresh rate 31 5 kHz 720 x 400 31 5 kHz 640 x 480 37 5 kHz 640 x 480 37 9 kHz 800 x 600 46 9 kHz 800 x 600 48 4 kHz 1024 x 768 60 0 kHz 1024 x 768 64 0 kHz 1280 x 1024 80 0 kHz 1280 x 1024 For ergonomic reasons a screen resolution of 1280 x 1024 pixels is recommended Because of the technology used active matrix an LCD monitor provides a totally flicker free picture even with a refresh rate of 60 Hz 28 A26361 K1143 2120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P 19 3 Pin assignment D SUB Green video earth 15 DDC Clock Blue video earth TMDS Data2 9 TMDS Datal TMDS Data0 TMDS Data2 TMDS Data1 TMDS Data0 TMDS Data 2 4 Shield TMDS Data 1 3 Shield TMDS Data 0 5 Shiel
16. d 8 Analogue Vertical Sync Hot Plug Detect TMDS Clock A26361 K1143 2120 1 7619 edition 3 29
17. e the screen display should be optimally adapted to the screen controller used and adjusted in accordance with vour needs Choosing basic monitor settings using the supplied software If one of the operating systems Windows 95 98 Windows NT Windows Me Windows 2000 Windows XP or OS 2 with Windows emulation installed is used the basic monitor settings can be set with the CD supplied gt Insert the supplied CD into the CD ROM drive gt Open the Readme file on the CD and follow the instructions in the file Your monitor should now already be properly adjusted If none of the above operating systems is used or minor corrections are to be made to the screen display then change the monitor settings with the OSD menu Changing the monitor settings with the buttons of the control panel setectT menu W A INPUT EX AUTO fu i l L 1 2 3 1 Buttons for the OSD menu 2 ON OFF switch On Screen display 3 Power indicator Use the buttons of the control panel to make the following monitor settings directly while the OSD menu is switched off Performing auto adjustment of the monitor gt Press the AUTO button for approx 1 second while the OSD menu is switched off The Auto Processing message is displayed Picture quality and position are set to optimum values for your system Selecting input signal D SUB DVI D gt Press the INPUT button for calling the nput select setting window gt Pres
18. elines for energy efficiency Disposal and recycling This device has been manufactured to the highest possible degree from materials which can be recycled or disposed of in a manner that is not environmentally damaging The device may be taken back after use to be recycled provided that it is returned in a condition that is the result of normal use Any components not reclaimed will be disposed of in an environmentally acceptable manner If you have any questions on disposal please contact your local office our help desk or Tel 49 5251 81 80 10 Fax 49 5251 81 80 15 http www fujitsu siemens de wvm Fax 32 2 706 86 13 E Mail info recupel be http www recupel be Germany Belgium Switzerland Fujitsu Siemens Computers RECUPEL SWICO GmbH Boulevard Reyers 80 Schweizerischer Remarketing und Recycling B 1030 Brussels Wirtschaftsverband der D 33106 Paderborn Tel 32 2 706 86 16 Informations Kommunikations und Organisationstechnik A list of the SWICO Acceptance places can be found at http www swico ch Asia USA Taiwan Environmental Protection Administration Executive Vuan R O C http recycle epa gov tw Fujitsu Siemens Computers Inc 1250E Arques Avenue Sunnyvale CA 94085 U S A Contact Schroettle Henning Bernd Phone No 408 834 0306 Fax No 408 746 8299 You can find more information on the Internet at www fujitsu siemens com recycling A263
19. er management If your computer is equipped with power management the monitor can support this function fully Here the monitor does not distinguish between the individual energy saving modes of the computer standby mode suspend mode and OFF mode as it is capable of immediately switching into the mode with the highest energy saving effect Powerindicator indicator lights up blue lights up orange p Perren the monitor is working the screen is dark normally Power consumption Normal reduced to lt 1 W lt 37 W typical If your computer detects inactivity no input it sends an appropriate signal to the monitor to reduce the power consumption energy saving mode The power indicator of the monitor changes colour to indicate the status change Once an input is made at the computer the screen contents are redrawn and full power is restored For detailed information on how energy saving mode operates refer to the operating manual or technical manual of the computer system a power consumption of up to 1 W is maintained to feed the circuit for redrawing lil When the monitor is switched to the energv saving mode bv the power management the screen contents In order to stop the monitor from using any power at all switch it off at the main switch on the underside P19 3 A26361 K1143 2120 1 7619 edition 3 17 SCENICVIEW B17 3 B19 3 P19 3 Changing the monitor settings When putting the monitor into operation for the first tim
20. leanings miat er at oes hee ela ta ta ped cee ane ee GCE MmarkM ka a k aa doh ee ain ns See die oa A ae ie af FCC Class B Compliance Statement Declaration of Conformitv Energy Star Guidelines i i a gh a eine eisen Disposal and recycling iii tin ia a a ap a a a a ja Checking the contents of the consignment Installing an ergonomic video workstation Mounting and removing the monitor base ss sena rna nn nn nr rna n anna Foldin e ut monitor bAaSB L sil a A A a ob b A lta Removing monitor base Connecting the monitor a Connecting cables to the monitor nn Connecting cables to the COMpUtEr LQ nn n rna nr Operation of the monitor Adjusting height rake and rotation a Adjusting portrait format 2 i L eee ek Switching the monitor on and off B17 3 B19 3 2 nar 15 Switching the monitor on and off P19 3 Notes on power management ee Changing the monitor settingS s nanna Notes on ergonomic colour adjustment rna an nn nanna nr nanna ann Troubleshooting aa aena iaaa ieiet Notes regarding the DIN EN ISO 13406 2 standard Technical a i ss sscghecsa udivsceasseduncsestga tea tives acenseivdatca saeasdeesucoesisalavduis ehe Festen VESA DDC compatible VGA interface Preset operating modes Pin assignment D SUB Be Monitor port DVI Dimi aaa na d A A26361 K1143 Z120 1 7619 edition
21. left edge of the casing and move it up or down The rake of the monitor can be adjusted by 2 forward and 35 back from its vertical position gt Grasp the monitor with both hands on the right and left edge of the casing and adjust it to the desired rake The monitor can be turned horizontally by approximately 90 from its central position gt Grasp the monitor with both hands on the right and left edge of the casing and turn it to the desired position 14 A26361 K1143 2120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P19 3 Adjusting portrait format The monitor can be turned from the wide format landscape mode into the high format position portrait mode gt Grasp the monitor with both hands on the right and left edge of the casing move it into the highest position and turn it clockwise until it is in the portrait position shown in the portrait mode This software is included in the deliverv CD ROM and must lil Vou must use corresponding software pivot software so that the screen displav is also be installed on vour computer gt Inthe OSD menu you have the option of switching the OSD manually from landscape mode into portrait mode see section Monitor settings using the OSD menu To reset the monitor to the landscape mode the monitor must be turned counter clockwise The OSD display can be reset again in the OSD menu Switching the monitor on and off B17 3 B19 3 The ON OFF switch at the fro
22. ng manual contains important information vou require to start up and run vour LCD monitor A graphics card screen controller with VGA interface or a digital graphics card with DVI interface is required to control the SCENICVIEW B17 3 B19 3 P19 3 LCD monitor The monitor processes the data supplied to it bv the screen controller The screen controller or the associated driver software is responsible for setting the modes resolution and refresh rate When putting the monitor into operation for the first time the screen display should be optimally adapted to the screen controller used and adjusted in accordance with vour needs see the Changing the monitor settings section in the Operation of the monitor chapter Target group You don t need to be an expert to perform the operations described here However please observe the safetv information given in the operating instructions of the computer and in this manual In the event of anv problems occurring please contact vour sales outlet or our help desk Additional information Details of how vou set the resolution and refresh rate are provided in the documentation on vour screen controller the associated driver software For ergonomic reasons we recommend a screen resolution of 1280 x 1024 pixels for the monitors SCENICVIEW B17 3 B19 3 and P19 3 Because of the technologv used active matrix an LCD monitor provides a totallv flicker free picture even with a refresh rate of 60 Hz
23. ng points If the distortion is still not eliminated the monitor should if possible be checked on another computer If vou are unable to solve the problem please inform our help desk Having this problem2 Check the following points No screen displav power indicator does not light gt Check whether the main switch on the underside of the monitor is switched on P19 3 gt Check whether the power cable on the monitor is connected correctly gt Check whether the computer is switched on No screen display power indicator lights v Check whether the computer is switched on gt Check whether the data cable for the monitor is correctly attached to the monitor port on the computer gt Press any key on the computer keyboard the computer may be in energy saving mode gt Alter the brightness and or contrast until you get a Frequency out of range kHz Hz Please change the display mode to 1280 x 1024 with 60 Hz picture Message gt Check whether the data cable for the monitor is No Signal correctly attached to the monitor port on the computer gt Check whether the computer is switched on Message The input signal horizontal frequency and refresh rate at the displayed input does not correspond to the technical monitor data gt Adjust the video frequency range using the computer software see documentation for your computer or your graphics card gt
24. nt is used for switching the monitor on and off 1 Buttons for the OSD menu On Screen display 2 ON OFF switch 3 Power indicator li The buttons are to be pressed from the bottom upwards A26361 K1143 2120 1 7619 edition 3 15 SCENICVIEW B17 3 B19 3 P19 3 Switching the monitor on and off P19 3 The main switch on the underside and the On Off switch on the front of the monitor are used to switch it on and off gt Switch on the monitor via the main switch 4 on the underside 1 Buttons for the OSD menu on screen displav 2 On Off switch 3 Mains power indicator 4 Main switch The mains power indicator 3 lights up blue when the monitor and the computer are switched on The mains power indicator lights up orange when the monitor is not receiving a video signal or when it is in energy saving mode The mains power indicator goes out when the monitor is switched off When you switch the computer system on you must proceed in the following order gt First switch on the LCD monitor with the ON OFF switch 2 gt Then switch on the computer If your computer has a power management function energy saving mode you should read the Notes on power management section in this chapter 16 A26361 K1143 2120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P19 3 Notes on pow
25. of liquids or foreign matter switch off the unit disconnect the power plug and contact vour sales outlet or our help desk e The monitor must be disposed of in accordance with the local regulations for disposal of special waste The screen background lighting contains mercurv Vou must observe the applicable handling and disposal safetv regulations for fluorescent tubes e Oniv qualified technicians should repair the device Unauthorised opening and incorrect repair may greatly endanger the user electric shock fire risk e You may set only those resolutions and refresh rates specified in the Technical data chapter Otherwise you may damage your monitor If you are in any doubt contact your sales outlet or our help desk Q Use a screen saver with moving images and activate the power management for vour monitor to prevent still images from burning in e If you operate the monitor with the swivel arm or wall bracket it may not be turned by 180 e The SCENICVIEW B17 3 B19 3 P19 3 monitor may only be operated in landscape mode 0 and portrait mode 90 The control buttons are located at the bottom of the monitor in landscape mode 0 and at the left hand side of the monitor in portrait mode 90 Q Store this manual close to the device If you pass the device on to third parties you should pass this manual on with it A26361 K1143 2120 1 7619 edition 3 3 SCENICVIEW B17 3 B19 3 P19 3 Power cable To guarantee safe
26. operation use the cable supplied Use the following guidelines if it is necessarv to replace the original cable set Q The female male receptacles of the cord set must meet IEC60320 CEE 22 requirements Q The cable has to be HAR certified or VDE certified The mark HAR or VDE will appear on the outer sheath Q For devices which are mounted on a desk or table tvpe SVT or SJT cable sets mav be used For devices which sit on the floor only SJT type cable sets may be used Q The cable set must be selected according to the rated current for vour device e If necessarv replace the original power cable with a regular grounded 3 core mains lead Transport e Transport the monitor with care and oniv in its original packaging or another corresponding packaging fit to protect it against knocks and jolts Q Never drop the LCD monitor danger of glass breakage Cleaning Q Always pull out the power plug before you clean the monitor Q Do not clean anv interior parts vourself leave this job to a service technician Q Do not use anv cleaning agents that contain abrasives or mav corrode plastic Q Ensure that no liquid will run into the svstem e Ensure that the ventilation areas of the monitor are free Q The display surface of the LCD monitor is sensitive to pressure and scratches Clean it only using a soft slightly moistened cloth Wipe the monitor casing with a dry cloth If the monitor is particularly dirty use a cloth which has been moi
27. ronisation Horizontal frequency Refresh rate Maximum pixel rate Power supply Total power consumption Sound output A26361 K1143 2120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P19 3 B17 3 B19 3 P19 3 43 cm 48 cm 0 264 mm 0 294 mm 337 9mm 376 3 mm 270 3 mm 301 mm 1280 x 1024 1280 x 1024 375 mm 412 mm 469 mm 497 mm 249 mm 249 mm 438 mm 484 mm 418 mm 452 mm 176 mm 176 mm approx 6 8 kg approx 7 5 kg 25 25 Class Il Class Il Power cable 1 8 m D SUB data cable 1 8 m DVI D data cable 1 8 m Audio cable 1 8 m Analogue positive 0 7 Vpp 75 Q Digital DVI D Separate Sync TTL positive or negative 30 kHz 82 kHz multi scanning 56 Hz 76 Hz 135 MHz switches automatically 100 V 240 V 50 Hz 60 Hz lt 37 W in normal mode lt 1 W in energy saving mode standby mode suspend mode and OFF mode 2 0 W left 2 0 W right 27 SCENICVIEW B17 3 B19 3 P19 3 Environmental conditions Environment class 3K2 IEC 721 Rated range of operation 15 C 35 C Humiditv 20 85 Limit range of operation 5 C 35 C Humiditv 20 85 Condensation must be avoided VESA DDC compatible VGA interface Your monitor is equipped with a VESA DDC compatible VGA interface VESA DDC Video Electronics Standard Association Display Data Channel is used as the communications interface between the monitor and the computer If your computer is equipped with a VESA DDC
28. s e Reorient or relocate the receiving antenna e Increase the separation between equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Fujitsu Siemens Computers GmbH is not responsible for anv radio or television interference caused bv unauthorised modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified bv Fujitsu Siemens Computers GmbH The correction of interferences caused bv such unauthorised modification substitution or attachment will be the responsibilitv of the user The use of shielded I O cables is required when connecting this equipment to any and all optional peripheral or host devices Failure to do so may violate FCC and ICES rules Declaration of Conformity This device complies with Part 15 ofthe FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Product name Colour LCD Monitor Trade name Fujitsu Siemens Computers Inc Model number s SCENICVIEW B17 3 B19 3 P19 3 Name of responsible partv Fujitsu Siemens Computers Inc 1250E Arques Avenue Sunnvvale CA 94085 U S A Contact person Schroettle Henning Bernd
29. s the w or a button to select the desired input analogue D SUB or digital DVI D This setting window can also be called when the OSD menu is locked Activating deactivating muting gt Press the td button to switch the sound off and on again A message is displayed that the action has been performed 18 A26361 K1143 2120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P19 3 Locking the OSD menu The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings gt Press and hold the SELECT MENU button for a few seconds while you switch on the monitor with the ON OFF switch A message is displayed that the action has been performed Please proceed in the same manner to release the locked OSD menu again Locking the ON OFF button The ON OFF switch can be locked to prevent accidental or unauthorised changes to the monitor settings gt Press and hold both buttons w and a simultaneously for a few seconds A message is displayed that the action has been performed Please proceed in the same manner to release the locked ON OFF switch again Monitor settings using the OSD menu With the buttons on the control panel call up and use the integrated OSD On Screen display menu the following description default setting With the OSD function Language in the OSD Setup lil The OSD menu is available in different languages The English menu names are used in you can select another language To set the OS
30. stened in mild domestic detergent and then carefully wrung out CE marking Directives 2004 108 EC Electromagnetic Compatibility and 2006 95 EC Low Voltage The shipped version of this device complies with the requirements of the following EC C Directive 4 A26361 K1143 Z120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P19 3 FCC Class B Compliance Statement The following statement applies to the products covered in this manual unless otherwise specified herein The statement for other products will appear in the accompanving documentation NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference Causing Equipment Standard ICES 003 for digital apparatus These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequencv energv and if not installed and used in strict accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more ofthe following measure
31. t the monitor A26361 K1143 2120 1 7619 edition 3 13 SCENICVIEW B17 3 B19 3 P19 3 Connecting cables to the computer Information on the computer connections and interfaces is contained in the operating manual for vour computer If your computer has two monitor ports onboard screen controller and separate graphics card the monitor port for the separate graphics card is usuallv active gt Connect the data cable to the active monitor port on the computer and secure the plug in connection by tightening the safety screws gt Insert the other plug of the audio line in the audio output of the computer gt Plug the connector of the mains cable provided into the monitor outlet of the computer or into a properly earthed outlet and ensure a safe connection gt Plug the power connector of the computer into a properly grounded mains outlet appropriate graphics drivers for your application software Details of how to do this are i When you start working with your monitor for the first time you should install the provided in the documentation on your screen controller the associated driver software Operation of the monitor The monitor offers the following possibilities that enable it to be optimally adjusted for the respective user and the respective situation Adjusting height rake and rotation The height of the monitor can be adjusted by approximately 120 mm gt Grasp the monitor with both hands on the right and
32. the monitor for optimum viewing The viewing distance to the monitor should be approximately 50 cm Example layout of monitor keyboard and copy holder 1 Preferred viewing distance 2 Permissible viewing distance Position the monitor for optimum viewing The viewing distance to the monitor should be approximately 50 cm lil Keep ventilated areas clear Depending on the situation the use of a swivel arm or wall bracket VESA FPMPMI are available from specialised dealers mav be advisable For this purpose the monitor base must be removed beforehand as described in the Mounting and removing the monitor base chapter A26361 K1143 2120 1 7619 edition 3 SCENICVIEW B17 3 B19 3 P19 3 Mounting and removing the monitor base The display surface is susceptible to scratching Therefore lav the monitor on a soft surface when mounting or removing the monitor base Folding out monitor base When delivered the lower part of the monitor base is folded up and secured to the monitor bv a collar N The monitor base springs up about 5 cm when the collar is released gt Lay the monitor on its face on a soft surface A gt First release one of the collar fasteners 1 gt Release carefully the second collar fastener 2 The monitor base can now be folded out A26361 K1143 2120 1 7619 edition 3 9 SCENICVIEW B17 3 B19 3 P19 3 Z L u gt
33. tical position With this function you move the picture up or down Clock Setting synchronisation With this function you adjust the picture width to eliminate vertical picture disturbances Phase Eliminating picture interference With this function you fine tune your monitor to eliminate picture interference Adjusting the volume Calling the Audio setting window Setting the volume for plavback with the integrated loudspeakers Switching the loudspeakers off or on Volume Setting colour temperature and colours Calling the Colour setting window Selecting the colour temperature The warmth of the screen colours is set using the colour temperature The colour temperature is measured in K Kelvin You can select from sRGB 6500 K 9300 K Native and Custom Colour sRGB setting colour display according to the sRGB standard Native Original colour of the LCD display Custom Colour User defined colours In the user defined setting you can change the colour ratios of the basic colours red green blue as required A26361 K1143 2120 1 7619 edition 3 21 SCENICVIEW B17 3 B19 3 P19 3 Setting displav of the OSD menu EJ Calling the OSD Setup setting window Language Setting language for the OSD menu With this function vou choose between English default setting French German Italian and Spanish as the language for the OSD menu OSD Setting the horizontal position of the OSD menu H
Download Pdf Manuals
Related Search