Fujitsu 15C Scanner User Manual
Contents
1. b Remove the multi fed sheets of paper c Close the ADF unit d Flatten the corners and edges loosen the paper before reloading it in the paper guide e Check the feeding roller condition and do the cleaning if necessary See Chapter 3 4 1 Question Answer Paper becomes skewed in the Scanner a Check the feeding roller condition do the cleaning if necessary See Section 3 1 b Use the paper guide when feeding the paper Question When I power on the Scanner it makes noises and will not Answer stand ready There are two possibilities a You forgot to remove the shipping retainer from the Scanner Please remove the shipping retainer first b You did not place the Scanner on a flat desktop surface This may cause the Scanner to function improperly Question When I power on the Scanner the lamp does not light Answer Question Answer The possibilities are as follows a The lamp is out of order In that case contact your authorized local dealer to change the lamp The life time of the lamp is about 5000 hours b The fuse on main board of the Scanner is burned Check the main board of the Scanner If the fuse is burned put in a new fuse that is 250V 2A C If the fuse burns again after the changing it means the invertor of the lamp is burned Contact your authorized local dealer to replace the invertor Getting image from the Scanner is not a problem but when scanning the Sc2. dee hh eme e e e eius 5 2 ii 1 INTRODUCTION Congratulations on your purchase of Fujitsu Scanpartner 15C Scanner Before you install and operate the new Scanner please take a few minutes to read through this manual It provides you with the proper instructions on how to unpack install operate and maintain the Scanner Figure 1 1 shows how the Scanner is packed You can check all items against your checklist included with your Scanner 1 1 Power Cable Signal Cable Optional Package User s Manual Driver Kit Output Paper Stacker Output Paper Rack gS gt X Scanner Body Interface Card Foam Right Carton Figure 1 1 Scanner packing 1 2 2 INSTALLATION AND CONNECTIONS Please unpack the Scanner carefully and check the contents against the checklist If any items are missing or damaged please contact your authorized local dealer immediately Precautions Keep the Scanner out of direct sunlight Direct exposure to the sun or excessive heat may cause damage to the unit Do not install the Scanner in a humid or dusty place Be sure to use the proper AC power source Place the Scanner securely on an even flat surface Tilted or uneven surfaces may cause mechanical or paper feeding problems e Retain the Scanner box and packing materials for shipping purposes 2 1 Shipping Bracket The Scanner has a bracket that locks the carrier mechanism for transpor
3. mm WxDxH Appropriate 26 5 lbs 12 kg 5 2
4. 2 Wipe the glass of flatbed area and ADF area by moving the swab from side to side Close the ADF unit and document cover Your Scanner is now ready for use Figure 3 2 The Cleaning Area 3 3 4 TROUBLESHOOTING The Scanner will automatically perform a simple self test each time it is turned on This will help spot major system errors in the Scanner itself When the test is initiated the READY LED is flashing When the test is completed if no error occur the READY LED is steadily on If you have problems with the operation of your Scanner please check the following troubleshooting hints 4 1 Question and Answer Question The LED indicates that the Scanner is ready but the Scanner Answer response and Question Answer Question Answer does not respond to the scan command form the host computer a Please check the signal cable is firmly seated and invoke the scan command again If there is still no please reset the Scanner by turning it off and then on again reboot your host computer as well b Check if the driver is correctly installed You can use the DIAG EXE file in Fujitsu Driver Kit to check this out C Try to select another port memory Paper becomes jammed during scanning a Open the ADF unit b Pull out the jammed paper carefully c Close the ADF unit More than one sheet of paper were fed into the Scanner a Open ADF unit
5. Figure 2 4 Setting the ADF Paper Chute 2 5 2 4 ADF Output Tray Figure 2 5 i Hold the output paper rack some 30 degrees aslant as shown in Figure 2 5 ii Insert the three protrusions on the output paper tray to the three slots on the ADF iii Release the paper tray gently Make sure the tray is firmly attached to the ADF iv Pullout the output paper tray extension wire to the desired length Protrusions Extensions Figure 2 5 Install the ADF Output Paper Tray 2 6 2 5 Document Loading For flatbed scanning Documents that can not be scanned using the ADF can be placed on the flatbed for scanning Refer to Figure 2 6 i Place the document to be scanned onto the document glass face down ii Position the document so that the upper right corner is aligned with the reference mark Document cover Document holding pad Reference mark Document Document board glass Reference frame Figure 2 6 Place Document on the Scanner 2 7 2 6 ADF Scanning Standard paper size can be scanned automatically using the ADF Refer to figure 2 7 i To prevent occasional paper jam when automatically feeding multiple documents fan the paper before loading ii Lift the balance wire and place the documents to be scanned onto the ADF paper chute face down with the leading edge in the auto feeder entrance Let the balance wire rest on the top of the documents ii
6. Scanpartner 15C Image Scanner User s Manual Version 1 0 Doc No 250 0062 0 Table of Contents 1 INTRODUCTION pietre ead basado pee Elo esa pee aevo e mie evd niens 1 1 2 INSTALLATION AND CONNECTIONS e eeeeeeee ense teen enean nnno 2 1 2 I SHIPPING BRACKET i es eel Set tee fete aee e e ches eee che e eet ete e e eee Re 2 1 2 1 1 Removing the Shipping Bracket refer to figures 2 1 and 2 2 2 1 2 1 2 Refitting the Shipping Bracket sedis napi DR rdi brisa Qo HR uos 2 3 2 2 9C SE INTERFACE DEVICEID 3 noon RH OD EAEAN EEEE 2 3 2 3 ADF PAPER CHUTE FIGURE 2 4 pem eee eee epi ep 2 5 ZA ADF OUTPUT ERAY FIGURE 2 5 retro a e eite teas 2 6 2 5 DOCUMENT LOADING A irre etea eere Utd ete aer esas a ddr erac abe be e eb Roe bern 2 7 2 0 ADE SCANNING 15 he neo niti tet E aaa ate 2 8 2 7 CONNECTING THE CABLE 36 ene eR Dre Pet De Ier EE TR nines 2 9 9 MAINTENANCE i ssc erar E UR RES ERN E CERIS RUE EE 3 1 3 CLEANING THE A DES 32 4 2g Ign up End enn ue R E 3 1 OY CLEANING THE GEASS 7 edo At dnt AERARII AERE RUD 3 3 4 TROUBLESHOOTING tiic ates dissin tien hoo qoe orssed isese vinsero iiio ais 4 1 ALL OQUESTION AND ANSWER 5 eere e rece a te Ene e ce ee E Eee er erede Rege 4 1 4 2 PAPER JAM N THEA DE iiie teet ire Gere UO RH UR HR P UE ERPE UAR EISE UP RAPERE ARE LAN G 4 3 5 SPECIFICATIONS ue ostea pho EE ERR RED eT aie eE EIE MIT Us cee QUIDEM e DUAE UE E AR 5 1 5BIESCANPARTNER 5C SPECIFIGATIONS 3 5n
7. anner or system will often crash Please check a If the cable is firmly seated b Only two SCSI terminators can be connected to your SCSI daisy chain One is at the end of the SCSI device another is already in your host adapter Question While scanning the Scanner often makes noises or it scans back and forth Answer Please choose lower speed from the TWAIN user interface for low speed PC 4 2 4 2 Question The scanned image always comes out to be too dark Answer a Use your application to modify the Gamma setting to 2 2 and 1 8 for your printer and monitor respectively b Use Brightness setting from the TWAIN user interface to get a brighter image Question The Scanner works well otherwise but for the line art the lines of which seem much thicker than those of the original Answer Use the Brightness or Threshold setting to adjust the line art image Paper Jam in the ADF In the event of paper jam please follow the procedures below i Press the button at the front left of the Scanner as shown in Figure 4 1 arrow A The ADF cover will be released ii Open the ADF cover to the full open position arrow B iii Pull the paper out of the ADF unit carefully as shown in Figure 4 2 arrow A Figure 4 1 ADF Paper Jam Opening the ADF 4 3 c o E 3 9 ea blank side Figure 4 2 ADF Paper Jam Removing the Paper 4 4 SPECIFICATIONS All specifications are subject to change
8. e However it still needs to be cleaned occasionally to ensure optimum image quality and performance From time to time the pad assembly and feeding rollers may become contaminated with ink toner particles or paper dust In this case the scanner may not feed documents smoothly or several documents may feed at once If this occurs please follow the cleaning procedures to return your Scanner to its original state The cleaning procedures Figure 3 1 i Moisten a cotton swab with isoprophyl alcohol 95 Cleaner kits are available from Fujitsu ii Open the ADF unit by depressing the button in front of the ADF unit carefully open the ADF to the left 2 Wipe the feeding rollers by moving the swab from side to side Rotate the rollers forward with your finger and repeat the above cleaning procedures until the rollers are clean Be careful not to snag or damage the pick springs iii Wipe the pad in the direction from top to bottom Be careful not to hook the pick springs iv Close the ADF unit Your Scanner is now ready for use 1 Documents do not feed smoothly or easily 2 Several documents feed at one time 3 1 Feeding Roller Pad Assembly Figure 3 1 Opening the ADF unit and Document Cover 3 2 3 2 Cleaning the Glass The procedures i ii iii Soak a cotton swab with some isoprophy alcohol 95 Open the ADF unit and document cover as shown in Figure 6
9. i Adjust the left and right guides so that they are snug against the sides of the documents Left guide Auto feeder hole Right guide Balance Wire Document blank side ADF paper chute Document size scale Figure 2 7 Use ADF to Load Multiple Documents 2 8 2 7 Connecting the Cable i Turning the Power Off Depress the side marked O to turn the power off Connect the power cable and SCSI signal cable as shown in Figure 2 8 ii Turning the Power On Depress the side marked T to turn the power on The POWER LED will light If not please check the power source iii SCSI Termination The Fujitsu Scanpartner 15C comes complete with a built in SCSI terminator If the Scanner is the last device in a SCSI chain the terminator should be switched on If the Scanner is not the last device the terminator should be off The terminator on off switch is located on the back of the Scanner to the left of the SCSI cable connectors SCSI Device Scanner Terminator Off Some Scanner Terminator On 2 9 COMPUTER CABLE POWER TO DTC 3151 OR SWITCH OTHER PC SCSI CARD Figure 2 8 Scanpartner 15C Scanner Cable Connection POWER CABLE COMPUTER POWER SWITCH Figure 2 9 Scanpartner 15C SCSI Scanner Cable Connections with Mac 2 10 3 MAINTENANCE 3 1 Cleaning the ADF Your Scanner is designed to be maintenance fre
10. ote For steps iv to vi please refer to figure 2 1 and 2 2 iv Carefully place the Scanner in an upright position on its front side v Usea suitable screwdriver to remove the screw holding the shipping bracket in the use position vi Put the shipping bracket into the shipping position with the long side extending into the Scanner base Secure it with the screw vii Carefully place the Scanner back into its normal position 2 2 SCSI Interface Device ID When you have several devices on a SCSI chain you may need to adjust the SCSI ID selector setting located on the back of the Scanner This setting assigns a specific device ID to the Scanner If the assignment conflicts with an existing SCSI device please select a new ID See Figure 2 3 Note The factory setting for Scanner is ID 6 Usually ID 0 is assigned to an internal hard disk drive and ID 7 to SCSI adapter or host ID 8 and 9 are not in actual use Using a suitable tool turn the selector switch until the arrow points to the desired ID number 2 3 SISI ID Selector SCSI ID Selector Figure 2 3 Adjusting the SCSI ID setting 2 4 2 3 ADF Paper Chute Figure 2 4 i Raise the right side of the paper chute to about 45 degrees ii Pull down the wire leg from under the paper chute iii Insert the wire leg into the grips on the document cover iv Pull out the paper chute extension to the length you want ADF paper chute Document cover
11. tation purposes This bracket must be put into the use position before using the Scanner If the power is turned on before the bracket has been removed the PAPER JAM light will turn on Before proceeding turn the power off disconnect all cables and follow the instructions below to remove the shipping bracket 2 1 1 Removing the Shipping Bracket refer to figures 2 1 and 2 2 i Carefully place the Scanner in an upright position on its front ii Using a suitable screwdriver remove the screw and pull out the shipping bracket iii Put the shipping bracket into the use positions with the short side extending into the Scanner base and secure it with the screw iv Carefully place the Scanner back into its normal position 2 1 SHIPPING POSITION Figure 2 1 Removing the Shipping Bracket USE POSITION Figure 2 2 Securing the Shipping Bracket 2 2 2 1 2 Refitting the Shipping Bracket Whenever you need to move the Scanner to a new location it is advisable to refit the shipping bracket to avoid causing damage to the Scanners internal mechanism Please follow the instructions below to refit the shipping bracket i Turn off the Scanner power at the power on off switch ii Open the document cover iii Turn off the Scanner N
12. without notice The following can not be properly fed by ADF 4 P 4 P 4 4 4 P 4 4 4 S Ww Paper with clip or staple attached Paper with ink not totally dry Paper with inconsistent thickness such as envelopes Paper with wrinkles curls folds or tears Tracing paper Coated paper Carbonless paper Paper narrower than 3 5 or wider than 8 5 Items other than papers such as cloth metal or OHP film Notched paper Paper with an odd non rectangular shape Very thin paper Please use the flatbed to scan documents that cannot be fed by the ADF 5 1 5 1 Scanpartner 15C Specifications Scanner Type Scanning Mode Optical Resolution Light Source ADF Capacity ADF Scanning Speed Scanning Document Size Max Interface Power Requirement Power Consumption Humidity Operation Temperature Storage Temperature Dimension Weight SN he d S iS e d S Ww K2 Ww K2 Ww K2 Ww K2 Ww K2 Ww K2 Ww SN Sd 4 4 P 4 4 4 P S SN Ww 1 pass colour Flatbed with ADF built in 30 bit colour Grey Scale 256 levels Line Art Halftone 64 levels Error Diffusion single bit 300 x 600 dpi in a dpi increments Cold Cathode fluorescent lamp 50 pages 15 PPM 200dpi B W mode ADF ADF mode 8 5 x 14 Flatbed mode 8 5 x 11 69 SCSI 2 90 264 Vac 47 63Hz 30 watts 20 to 80 10 to 40 10 to 50 570 x 350 x 165
Download Pdf Manuals
Related Search