Home

Frigidaire FGES3045KW Range User Manual

1. CAUTION Always use this cooking mode with the oven door closed or the convection fan will not turn on Electric Oven Convection Broiling Table Recommendations Food Item position Setting Steak 1 thick 4th 550 F 4th 550 F Pork Chops 3 4 thick 4th 550 F Chicken Bone In 3rd 450 F Chicken Boneless 4th 450 F Fish 3rd 500 F Shrimp 3rd 550 F Hamburger 1 thick 4th 550 F 4th 550 F 20 Cook Time st side 2nd side aR 6 00 4 00 Rare 7 00 5 00 Medium 8 00 6 00 Well 20 00 10 00 Well 8 00 6 00 Well 13 00 Well 5 00 Well 9 00 7 00 Medium 10 00 8 00 Well SETTING BAKE TIME Bake Time allows the oven to be set to cook for a specific length of time and shut off automatically The oven will shut off and will beep when the countdown is finished This feature can be used with Bake Convection Bake Convection Roast Pizza and Chicken Nuggets cooking modes To program the oven to begin baking immediately and to shut off automatically example BAKE at 350 F for 30 minutes 1 Be sure the clock is set for the correct time of day 2 Arrange interior oven rack s and place the food in the oven 3 Press BAKE 350 will appear in the display 4 Press START The actual oven temperature will appear in the display 5 Press BAKE TIME will appear in the display 6 Enter the desired baking time by pressing 3 0O 7 Press START Once
2. Note The size and type of cookware used will influence the setting needed for best cooking results Recommended Setting for Surface Element Setting Type of Cooking HIGH HI Start most foods bring water to a boil and pan broiling MEDIUM HIGH Continue a rapid boil frying deep fat 8 10 frying MEDIUM 6 Maintain a slow boil thicken sauces and gravies steaming vegetables MEDIUM LOW _ Keep foods cooking poaching and 2 4 stewing LOW LO Keep warm melting and simmering amp NOTE Radiant elements have a limiter that allows the element to cycle on and off even at the HI setting This helps to prevent damage to the ceramic smooth top Cycling at the HI setting is normal and can occur if the cookware is too small for the radiant element or if the cookware bottom is not flat BEFORE SETTING SURFACE CONTROLS Using proper cookware The size and type of cookware used will influence the setting needed for best cooking results Be sure to follow the recommendations for using proper cookware as illustrated in Figures 1 amp 2 Cookware should have flat bottoms that make good contact with the entire surface heating element Figure 1 Check for flatness by rotating a ruler across the bottom of the cookware CORRECT L e Flat bottom and straight sides e Tight fitting lids e Weight of handle does not tilt pan Pan is well balanced Pan sizes match the amount of fo
3. If soils remain carefully scrape soils with a metal razor blade scraper holding scraper at a 30 degree angle to the surface Remove loosened soils then apply a few drops of cleaning cream and buff surface clean CARE amp CLEANING Cleaning recommendations for the ceramic glass cooktop continued Plastic or foods with a high sugar content These types of soils need be removed immediately if spilled or melted onto the ceramic cooktop surface Permanent damage such as pitting of the cooktop surface may occur if not removed immediately After turning the surface elements OFF use a razor blade scraper or a metal spatula with a mitt and scrape the soil from the hot surface as illustrated Allow the cooktop to cool and use the same method for heavy or burned on soils Do not use the following on the ceramic glass cooktop e Do not use abrasive cleaners and scouring pads such as metal and some nylon pads They may scratch the cooktop making it more difficult to clean e Do not use harsh cleaners such as chlorine bleach ammonia or oven cleaners as they may etch or discolor the cooktop e Do not use dirty sponges cloths or paper towels as they can leave soil or lint on the cooktop which can burn and cause Special Caution for Aluminum Foil and Aluminum Cooking Utensils VEN SCOURING A PADS O CLEANER ABRASIVE CLEANERS Aluminum foil Use of aluminum foil will damage the cooktop
4. Do not place plastic items such as salt and pepper shakers spoon holders or plastic wrappings on cooktop when it Is in use These items could melt or ignite Potholders towels or wooden spoons could catch fire if placed too close to the surface elements Do not allow aluminum foil or ANY material that can melt to make contact with the ceramic glass cooktop If these items melt on the cooktop they will damage the ceramic cooktop amp NOTE The surface Element On indicator lights will glow when one or more elements are turned on A quick glance at these indicator lights when cooking is finished is an easy check to be sure all surface elements are turned off 14 A Figure 1 v O O O O hi ai hi hi or hi s KN o O lo lo Figure 2 S gt Figure 4 Figure 5 Front portion Front amp Middle only portions Figure 6 Front amp Middle plus Left Rear CAUTION Radiant surface elements may appear to have cooled after they have been turned OFF HE Hot Element message will turn ON and will continue to glow until the glass cooktop has cooled down to a moderate level The glass surface may still be hot and burns may occur if the glass surface is touched before the indicator light has turned OFF The message may remain on even though the controls are turned OFF Keep warm zone Models B amp C only The purpose of the keep warm zone is to keep hot cooked foods at serving temperature
5. amp C only Flat half oven rack Closed position Figure 5 Models B amp C only Effortless oven rack CAUTION Always use pot holders or oven mitts when adjusting the oven racks Wait until the oven has completely cooled if possible Oven racks may be HOT and may cause burns The Flat Oven Handle Rack has an handle to facilitate the sliding of the rack when large amount of foods weight on it The Flat Oven Half Rack has a removable insert that can provide extra space for larger food items The right half rack portion may still be used for other food items like a casserole dish See Figure 3 amp 4 To remove the insert squeeze on the left front insert side See Figure 6 of the rack and tilt out clockwise To reinstall insert rear hooks at back of insert See figure 6 and lay insert down Make sure both insert front hooks snap into rack See figure 7 The Offset Oven Rack is used to maximize cooking space See Figure 2 The offset rack can be used in the lower rack position to roast large cuts of meat and poultry Do not use cookware that extends beyond the edge of the Flat Half Rack For best results allow 2 inches between the pan placed on the rack and oven side or rear walls Figure 7 17 BEFORE SETTING OVEN CONTROLS The Effortless oven rack system Some models are equipped with a special oven rack system that automatically partially extends the oven rack from the interior oven glides to a
6. are limited to one year or the shortest period allowed by law but not less than one year Electrolux shall not be liable for consequential or incidental damages such as property damage and incidental expenses resulting from any breach of this written limited warranty or any implied warranty Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages or limitations on the duration of implied warranties so these limitations or exclusions may not imply to you This written warranty gives you specific legal rights You may also have other rights that vary from state to state If You Keep your receipt delivery slip or some other appropriate payment record to establish the warranty period Need should service be required If service is performed it is in your best interest to obtain and keep all receipts Service Service under this warranty must be obtained contacting Electrolux at the addresses or phone numbers below This warranty only applies in the USA and Canada In the USA your appliance is warranted by Electrolux Major Appliances North America a division of Electrolux Home Products Inc In Canada your appliance is warranted by Electrolux Canada Corp Electrolux authorizes no person to change or add to any obligations under this warranty Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service company Product features or specifications as desc
7. number one priority We know you ll enjoy your new appliance and Thank You for choosing our product We hope you consider us for future purchases PLEASE CAREFULLY READ AND SAVE THESE INSTRUCTIONS This Use amp Care Manual contains general operating instructions for your appliance and feature information for several models Your product may not have all the described features The graphics shown are representative The graphics on your appliance may not look exactly like those shown These instructions are not meant to cover every possible condition and situation that may occur Common sense and caution must be practiced when installing operating and maintaining any appliance amp NOTE Please attach sales receipt here for future reference IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this appliance Save these instructions for future reference DEFINITIONS amp This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death 44 WARNING This symbol will help alert you to situations that may cause serious bodily harm death or property damage CAUTION This symbol will help alert you to situations that may cause bodily injury or property damage A IMPORTANT IMPORTANT indicates installation operation or maintenance information which is important but not hazard relate
8. with foil The exposed grease could catch fire e If using a Searing Grill available by mail order preheat the grill for 5 to 10 minutes before placing your meat e Convection broiling is generally faster than conventional broiling Check for doneness at the minimum recommended time 44 WARNING Should an oven fire occur leave the oven door closed and turn off the oven If the fire continues throw baking soda on the fire or use a fire extinguisher DO NOT put water or flour on the fire Flour may be explosive and water can cause a grease fire to spread and cause personal injury To set a Convection Broil Temperature of 500 F 1 Arrange oven racks 2 Press CONVECT 350 will be displayed CONVECT and BAKE will flash 3 Press CONVECT again 350 will be displayed CONVECT and ROAST will flash 4 Press CONVECT again 550 will be displayed CONVECT and BROIL will flash 5 Enterthe desired roasting temperature using the number pads 500 6 Press START 500 CONVECT BROIL and the fan icon will be displayed 7 After 5 minutes of preheat place food in the oven amp NOTE Pressing CANCEL will stop the feature at any time Accessories available via the enclosed brochure Broiler Insert Broiler Pan amp Insert Pan Figure 1 Figure 2
9. 375 5 Place food in the oven amp NOTE Pressing CANCEL will stop the feature at any time To change the Bake Temperature ee changing from 375 F to 425 F After the oven has already been set to bake at 375 F and the oven temperature needs to be changed to 425 F press BAKE and 375 will appear in the display Press 4 2 5 Press START oe amp NOTE During the first rise of temperature the convection fan will be activated to allow the oven to reach its target temperature faster The Bake Broil and Convection elements will also cycle for a better heat distribution 23 SETTING OVEN CONTROLS SETTING CONVECTION BAKE This mode of cooking enables you to obtain the best culinary results when baking with multiple pans and racks Multiple rack baking may slightly increase cook time for some foods but the overall result is time saved Some food may cook faster and more evenly with Convection Bake Convection baking uses the three elements and a fan to circulate the oven s heat evenly and continuously within the oven The oven can be programmed for Convection baking at any temperature between 170 F to 550 F with a default temperature of 350 F Convection Baking Tips e Always preheat your oven before using the Convection Bake mode e During preheat the 3 elements and the convection fan are used in cycle to quickly heat the oven e If your recipe cooking temperature has already been converted for con
10. BAKE the numeric key pads for the temperature you want example for 425 C press 4 2 5 and then pressing START twice for Jewish Holidays only Remember that the oven control will no longer beep or display any further changes once the oven is set for the Sabbath feature Should you experience a power failure or interruption the oven will shut off When power is returned SF Sabbath Failure will be shown in the oven display and the cooktop displays models B amp C The oven and cooktop will not turn back on automatically If your food was nearly fully cooked you may allow the trapped heat in the oven to finish the cooking process Otherwise you should remove the food when the power failure occurs because you may only start the oven once during the Sabbath Jewish Holidays After the Sabbath observance turn OFF the Sabbath feature and be sure that all the control knobs are at the OFF position The appliance may be used again with all normal functions After the Sabbath observance turn OFF the Sabbath feature Press and hold both the BAKE TIME and DELAY pads for at least 3 seconds SAb will disappear from the display and the oven may be used with all normal functions For further assistance guidelines for proper usage and a complete list of models with the Sabbath feature please visit the web at http www star k org How the Electronic Surface Element Controls work when the Sabbath feature is ON model B amp C
11. Do not use under any circumstances Aluminum utensils Since the melting point of aluminum is much lower than that of other metals care must be taken when aluminum pots or pans are used Pans that boil dry may permanently damage cooktop by breaking fusing to or marking it 38 Care and cleaning of stainless steel Some models are equipped with stainless steel exterior parts Special care and cleaning are required for maintaining the appearance of stainless parts Refer to the General Care amp Cleaning table for detailed cleaning instructions Removing and replacing the lift off oven door CAUTION The door is heavy For safe temporary storage lay the door flat with the inside of the door facing down To Remove Oven Door 1 Open oven door completely horizontal with floor See Figure 1 2 Pull the door hinge locks on both left and right door hinges down from the oven frame completely towards the oven door See Figure 2 A tool such as a small flat blade screwdriver may be required 3 Firmly grasp both sides of oven door along the door sides Do not use the oven door handle See Figure 3 4 Close the door to the broil stop position the oven door will stop into this position just before fully closing 5 With the oven door in the broil stop position lift the oven door hinge arms over the roller pins located on each side of the oven frame See Figure 4 To Replace Oven Door 1 Firmly grasp both sid
12. Enter the desired roasting temperature using the number pads 3 7 5 5 Press START The actual oven temperature will be displayed CONVECT ROAST and the fan icon will be displayed The Bake Broil and Convection elements will also cycle for a better heat distribution amp NOTE Pressing CANCEL will stop the feature at any time amp NOTE The Bake Broil and Convection elements will cycle for a better heat distribution 25 SETTING OVEN CONTROLS SETTING CONVECTION BROIL some models Use this mode for thicker cuts of meat fish and poultry The Convection Broiling gently browns the exterior and seals in the juices Convection broiling uses the broil element and a fan to circulate the oven s heat evenly and continuously within the oven The oven can be programmed for Convection Broiling at any temperature between 400 F to 550 F with a default temperature of 550 F Convection Broiling Tips e For optimum browning preheat the broil element for 5 minutes e Broil one side until the food is browned turn and cook on the second side Season and serve e Always pull the rack out to the stop position before turning or removing food e Always use a broiler pan and its grid when broiling available by mail order It allows the dripping grease to be kept away from the high heat of the broil element e DO NOT use the broil pan without the insert available by mail order DO NOT cover the broil pan insert
13. If a different temperature than 425 F is needed enter the temperature now using the keypad digits 3 Press START The fan icon and the actual oven temperature will appear in the display 4 Place the pizza in the oven when the beep is heard 5 Ifneeded entera BAKE TIME see its section for further details 6 To turn OFF the Pizza feature at any time press CANCEL To set Pizza for a fresh pizza 1 Arrange interior oven racks 2 Press PIZZA pad twice Frh will appear in the display If a different temperature than 400 F is needed enter the temperature now using the keypad digits 3 Press START The fan icon and the actual oven temperature will appear in the display 4 Place the pizza in the oven when the beep is heard 5 Ifneeded entera BAKE TIME see its section for further details 6 To turn OFF the Pizza feature at any time press CANCEL SETTING CHICKEN NUGGETS The CHICKEN NUGGETS pad has been designed to give optimum cooking performance when cooking your favorite chicken nuggets The Chicken Nuggets pad is preset for a Convection Bake at 400 F with a Bake Time of 18 minutes ending with a Keep Warm setting If needed a different target temperature or Bake Time than the presets can be entered Chicken Nuggets Tips e For most type of chicken nuggets preheating is not required and the preset baking time of the feature will give you optimum results e For larger chicken tenders follow the pr
14. Panel and Decorative Trim Oven Racks DO NOT HAND CLEAN OVEN DOOR GASKET DO HAND CLEAN DOOR hasten 36 How to Clean Use hot soapy water and a cloth Dry with a clean cloth Using a soft cloth clean with mild dish detergent and water or a 50 50 solution of vinegar and water Follow by rinsing the area with clean water dry and polish with a soft cloth Glass cleaners may be used if sprayed on a soft cloth first DO NOT spray liquids directly on the control pad and display area Do not use large amounts of water on the control panel excess water on the control area may cause damage to the appliance Do not use other liquid cleaners abrasive cleaners scouring pads or paper towels they will damage the finish To remove control knobs turn to the OFF position grasp firmly and pull straight off the shaft To replace knobs after cleaning line up the flat sides of both the knob and the shaft then push the knob into place Before cleaning the control panel turn all controls to OFF and remove the control knobs To remove pull each knob straight off the shaft Clean as instructed above Squeeze excess water from the cloth before wiping the panel especially when wiping around the controls Excess water in or around the controls may cause damage to the appliance To replace knobs after cleaning line up the flat sides of both the knob and the shaft then push the knob into place Clean burner grates broiler pan
15. Use the keep warm feature to keep cooked foods hot such as vegetables gravies casseroles soups stews breads pastries and oven safe dinner plates Always start with hot food It is not recommended to heat cold food on the keep warm zone All food placed on the keep warm zone should be covered with a lid to maintain quality For best results when warming pastries or breads the cover should have an opening to allow moisture to escape Do not use plastic wrap to cover food Plastic may melt onto the surface and be very difficult to clean Use only plates utensils and cookware recommended for oven and cooktop use on the keep warm zone To Set the keep warm zone control NOTE The controls and indicator light are located on the control panel 1 Touch the oneoff pad Fig 4 at the keep warm zone control position The keep warm indicator light will flash Note If no further pads are touched within 25 seconds the request to power the keep warm zone ON will clear 2 At the keep warmer zone controls position touch A once to turn ON the power level for HI Fig 1 or V to turn ON the power level for LO Fig 3 3 Each touch A or V will increase or decrease the power levels The keep warm zone has 5 power levels from HI Fig 1 through MED Fig 2 to LO Fig 3 The power level may be adjusted at any time while the keep warm zone is ON 4 When it is time to serve the food touch the oneoff pad once to turn the keep warm zo
16. and a fan to circulate the oven s heat evenly and continuously within the oven The oven can be programmed for Convection Roasting at any temperature between 170 F to 550 F with a default temperature of 350 F Convection Roasting Tips e Use a broiler pan and grid and a roasting rack available by mail order The broiler pan will catch grease spills and the grid will help prevent spatters The roasting rack will hold the meat e Place an oven rack on rack position 1 offset rack if available e No preheat is needed in convection roast e Make sure the roasting rack is securely seated on the grid in the broiler pan The roasting rack fits on the grid allowing the heated air to circulate under the food for even cooking and helps to increase browning on the underside available by mail order only e There is no need to reduce the convection temperature or to use the Convection Convert feature with this cooking mode e DO NOT use the broiler pan without the grid or cover the grid with aluminum foil available by mail order e Always pull the rack out to the stop position before removing food e Position food fat side up on the roasting rack To set a Convection Roast Temperature of 375 F 1 Arrange oven racks and place food in the oven 2 Press CONVECT 350 will be displayed CONVECT and BAKE will flash 3 Press CONVECT again 350 will be displayed CONVECT and ROAST will flash 4
17. broil temperature setting is 400 F press the desired temperature before continuing to step 5 5 Press START The oven will begin to broil 500 will appear in the display Preheat for 5 minutes before broiling Place the broiler pan on the rack Be sure to center the broiler pan directly under the broiler element Make sure the oven door is in the broil stop position See Figure 1 8 Broil on one side until food is browned turn and cook on the second side Season and serve Note Always pull the rack out to the stop position before turning or removing food 9 To stop broiling press CANCEL oe NO Broil Stop Position Figure 1 amp NOTE To assure your electronic controls safety when broiling with the oven door in broil position an high speed cooling fan will blow air through the trims above the door s WARNING Should an oven fire occur leave the oven door closed and turn off the oven If the fire continues throw baking soda on the fire or use a fire extinguisher DO NOT put water or flour on the fire Flour may be explosive and water can cause a grease fire to spread and cause personal injury Cook Time Rack Temperature Snel Ea Position E Steak 1 thick 4th 550 F 4th 550 F Pork Chops 3 4 thick 4th 550 F Chicken Bone In 3rd 450 F Chicken Boneless 4th 450 F Fish 3rd 500 F Shrimp 3rd 550 F Hamburger 1 thick 4th 550 F 4th 550 F 30 l l Do
18. cast iron metal ceramic or glass with rough bottoms can mark or scratch the cooktop surface Do not slide anything metal or glass across the cooktop Do not use your cooktop as a cutting board or work surface in the kitchen Do not cook foods directly on the cooktop surface without a pan Do not drop heavy or hard objects on the glass cooktop or they may crack it CARE amp CLEANING Cleaning recommendations for the ceramic glass cooktop CAUTION Before cleaning the cooktop be sure the controls are turned to OFF and the cooktop is COOL 44 WARNING DO NOT use a cooktop cleaner on a hot cooktop The fumes can be hazardous to your health and can chemically damage the ceramic glass surface For light to moderate soil Apply a few drops of CookTop Cleaning Creme directly to the cooktop Use a paper towel or use a non abrasive plastic type no scratch pad to clean the entire cooktop surface Make sure the cooktop is cleaned thoroughly leaving no residue For heavy burned on soil Apply a few drops of CookTop Cleaning Creme directly to the soiled area Rub the soiled area using a non abrasive plastic type no scratch pad applying pressure as needed Do not use the pad you use to clean the cooktop for any other purpose A IMPORTANT Damage to the ceramic glass cooktop may occur if you use an abrasive type scratch pad Only use cleaning products that have been specifically designed for ceramic glass cooktop
19. cool down and the oven door to unlock This normally takes about one hour So a 3 hour self clean cycle will actually take about 4 hours to complete Tt is recommend to use a 2 hour self clean cycle for light soils a 3 hour cycle for average soils and a 4 hour cycle for heavy soils to assure satisfactory results To set the controls for a 3 hour Self Cleaning cycle to start immediately and shut off automatically 1 Be sure the clock is set with the correct time of day and the oven door is closed 2 Press SELF CLEAN CLn and 3 00 HR will show in the display The control will automatically clean for a 3 hour period default self cleaning cycle time amp NOTE If a 2 or 4 hour clean time is desired press SELF CLEAN multiple times to toggle between 2 3 or 4 hours 3 Press START door Loc will appear a beep will sound and the DOOR and icon will flash the letters CLn will remain on in the display 4 As soon as the control is set the motor driven oven door lock will begin to close automatically Once the door has been locked the DOOR indicator light and A icon will stop flashing and remain on Also the oven icon will appear in the display amp NOTE Allow about 15 seconds for the oven door lock to close When the Self Clean Cycle is Completed 1 HOT will appear in the display The time of day the DOOR and icon will remain in the display 2 Once the oven has cool
20. display 4 Press START The actual oven temperature appears in the display 5 If you desire to set the oven control for a Bake Time or Delayed Bake Time do so at this time If not skip this step and continue to step 7 Refer to the Bake Time Delay Start section for complete instructions Remember the oven will shut down after using Bake Time or Delay Start and therefore may only be used once during the Sabbath Jewish Holidays 6 The oven will turn ON and begin heating 7 Press and hold both the BAKE TIME and DELAY START pads for at least 3 seconds SAb will appear in the display Once SAb appears in the display the oven control will no longer beep or display any further changes and the oven is properly set for the Sabbath feature 8 The oven may be turned OFF at any time by first pressing CANCEL pad this will turn the oven OFF only To turn OFF the Sabbath feature press and hold both the BAKE TIME and DELAY START pads for at least 3 seconds SAb will disappear from the display A IMPORTANT It is not advised to attempt to activate any other program feature other than BAKE while the Sabbath feature is active ONLY the following key pads will function after setting the Sabbath feature 0 to 9 BAKE START amp CANCEL All other keypads should not be used once the Sabbath feature is properly activated SETTING OVEN CONTROLS amp NOTE You may change the oven temperature once baking has started by pressing
21. display If a preheat of 350 F is needed press START 3 Press3 75 4 Press START PRE will be displayed while the oven is preheating amp NOTE While in preheat mode the convection fan will be activated during the first rise of temperature to allow the oven to reach its target temperature faster The Bake Broil and Convection elements will also cycle for a better heat distribution SETTING OVEN CONTROLS SETTING BAKE The BAKE pad controls normal baking If a rapid preheating is preferred refer to the POWERPLUS PREHEAT feature for instructions The oven can be programmed to bake at any temperature from 170 F to 550 F Baking Tips e Preheat your oven before using the bake mode e During preheat the 3 elements and the convection fan are used in cycle to quickly heat the oven e Use only one rack and center the pans as much as possible on rack 2 or 3 e If using two racks place the oven racks in positions 2 and 4 e Allow 2 to 4 5 1 to 10 2cm around the utensil s for proper air circulation e Be sure the pans do not touch each other the door sides or back of the oven To set the Bake Temperature to 375 F 1 Arrange interior oven racks 2 Press BAKE 350 will appear in the display If a bake of 350 F is needed press START 3 Press3 75 4 PressSTART The actual temperature will be displayed A beep will sound once the oven temperature reaches 375 F and the display will show
22. due to the sudden change in temperature Check the manufacturer s recommendations for cooktop use e Do Not Use Decorative Surface Burner Covers If an element is accidentally turned on the decorative cover will become hot and possibly melt Burns will occur if the hot covers are touched Damage may also be done to the cooktop FOR GLASS COOKTOP ONLY e Do Not Clean or Operate a Broken Cooktop If cooktop should break cleaning solutions and spillovers may penetrate the broken cooktop and create a risk of electric shock Contact a qualified technician immediately e Clean Cooktop Glass with Caution If a wet sponge or cloth is used to wipe spills on a hot cooking area be careful to avoid a steam burn Some cleaners can produce harmful fumes if applied to a hot surface e Avoid Scratching the Cooktop Glass with Sharp Objects IMPORTANT SAFETY INSTRUCTIONS FOR USING YOUR OVEN e Use Care When Opening Oven Door or Warm amp Serve Drawer if equipped Stand to the side of the appliance when opening the door drawer of a hot appliance Let hot air or steam escape before you remove or replace food in the oven drawer e Keep Oven Vent Ducts Unobstructed The oven is vented at the front above the oven door Touching the surfaces in this area when the oven is operating may cause severe burns Also do not place plastic or heat sensitive items on or near the oven vent These items could melt or ignite 44 WARNING NEVER cove
23. fully in place ALWAYS BE IN PLACE WHEN THE OVEN IS IN USE 2 Do not hit the glass with pots pans or any other object 3 Scratching hitting jarring or stressing the glass may A CAUTION weaken its structure causing an increased risk of BE SURE OVEN IS COOL breakage at a later time aL 7 To Replace the Light Bulb To remove the hidden bake cover 1 Turn the power off at the main source some models 2 Wear a leather faced glove for protection against 1 In order to remove the hidden bake cover pull the possible broken glass back edge with one hand about 1 2 inch and lift 3 Replace bulb with a 40 Watt appliance bulb only up the hidden bake cover with both hands See 4 For self cleaning oven press wire holder to one side picture to release glass shield change bulb and be sure to 2 When reinstalling the hidden bake cover be sure to replace glass shield put it all the way to the back of the oven and lay it down on the 2 shoulder screws Then push the front edge of the cover in its place below the front bracket To have easier access to the hidden bake cover you can remove the oven door by following the instructions on previous page IMPORTANT Always replace the hidden bake cover before the next use 39 CARE amp CLEANING To remove and replace storage drawer with extendible glide some models To Remove Storage Drawer 1 2 3 4 Open the drawer to the fully opened
24. into outlet Service wiring is not complete Call an authorized servicer Electrical power outage Check house lights to be sure Call your local electric company for service Cooktop control has detected a fault or error condition Try turning electrical power supply OFF and back ON to the appliance in order to reset main controls If fault recurs record fault number and unplug the appliance Electronic control has detected a fault condition Press CANCEL to clear the display and stop beeping Reprogram oven If fault recurs record fault number Press CANCEL and call an authorized servicer for assistance Replace or tighten bulb See Changing Oven Light section in this Use amp Care Guide Electrical power outage Check house lights to be sure Call your local electric company for service No power to the appliance Check steps under Entire Range or Oven Does Not Operate in this Before you Call checklist Incorrect control setting Make sure the correct control is on for the surface unit to be used Incorrect control setting Make sure the correct control is on for the surface unit to be used Lightweight or warped pans used Use only flat evenly balanced medium or heavyweight cookware Flat pans heat better than warped pans Cookware materials and weight of the material affect heating Heavy and medium weight pans heat evenly Because lightweight pans heat unevenly foods may burn easily Foods with acids such as tomatoes if al
25. position Locate the latches on both sides of the warmer drawer Pull up on the left glide latch and push down on the right glide latch Pull the drawer away from the appliance To Replace Storage Drawer 1 Align the glide latches on both sides of the drawer with the slots on the drawer 2 Push the drawer back into the appliance To remove and replace keep warm drawer some models 44 WARNING Turn power off before removing the warmer drawer To remove keep warmer drawer 1 3 Open the drawer to the fully opened position 2 Locate the latches on both sides of the keep warm drawer Pull up on the left glide latch and push down on the right glide latch Pull the drawer away from the appliance To clean keep warm drawer gently scour with a soapy scouring pad this will remove most spots Rinse with a 1 1 solution of clear water and ammonia If necessary cover difficult spots with an ammonia soaked paper towel for 30 to 40 minutes Rinse with clean water and a damp cloth Remove all cleaners or the porcelain may become damaged during future heating DO NOT use spray oven cleaners on the cooktop To replace keep warm drawer 1 2 Align the glide latches on both sides of the drawer with the slots on the drawer Push the drawer back into the appliance 40 44 WARNING Turn the keep warm drawer control knob to OFF before removing the drawer DO NOT touch the keep warm drawer element The
26. residue may be cleaned with a stiff nylon brush and water or nylon scrubber Be careful not to damage the oven gasket Excessive spillovers in oven especially for pie spillovers or large amounts of grease on the oven bottom Wipe up excessive spillovers before starting the Self Clean cycle If flames or excessive smoke are present stop the Self Clean cycle and follow the steps under Stopping or Interrupting the Self Cleaning Cycle in the Electronic Oven Control Guide 43 MAJOR APPLIANCE WARRANTY Your appliance is covered by a one year limited warranty For one year from your original date of purchase Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed used and maintained in accordance with the provided instructions Exclusions This warranty does not cover the following 1 Products with original serial numbers that have been removed altered or cannot be readily determined 2 Product that has been transferred from its original owner to another party or removed outside the USA or Canada 3 Rust on the interior or exterior of the unit 4 Products purchased as is are not covered by this warranty 5 Food loss due to any refrigerator or freezer failures 6 Products used in a commercial setting 7 Service calls which do not involve malfunction or defects in materials or workmanship or for appliances not in or
27. the Timed Bake feature has started the current time of day will appear in the display amp NOTE Baking time can be set for any amount of time between 1 minute to 6 hours The time remaining can be shown in the timer section of the display by pressing BAKE TIME at any moment of the cooking Press CANCEL when baking has finished or at any time to cancel the Timed Bake feature A Bake Time of 0 minute can also be entered to cancel the Bake Time feature and keep the oven in its current cooking mode amp NOTE After the Timed Bake feature has activated press BAKE TIME to display the bake time remaining in the Bake Time mode Once Bake Time has started baking a beep will sound when the oven temperature reaches the set temperature When the timed bake finishes 1 End and the time of day will show in display The oven will shut off automatically 2 The control will beep 3 times The control will continue to beep 3 times every 30 seconds until CANCEL is pressed CAUTION SETTING OVEN CONTROLS SETTING DELAY START The BAKE CONVECTION BAKE BAKE TIME and DELAY START pads control the Delayed Time Bake feature The automatic timer of the Delayed Time Bake will turn the oven on and off at the time you select in advance amp NOTE If your clock is set for normal 12 hour display mode the Delayed Timed Bake or Delayed Timed Convection Bake cycle can never be set to start more than 12 hours in advance To set f
28. the oven for more than 1 hour before cooking begins and should be removed promptly when cooking is completed Eating spoiled food can result in sickness from food poisoning 2 SETTING OVEN CONTROLS SETTING KEEP WARM This mode is best for keeping oven baked foods warm for serving after cooking has finished The KEEP WARM pad turns ON the Keep Warm feature and will maintain an oven temperature of 170 F 77 C The Keep Warm feature will keep oven baked foods warm for serving up to 3 hours after cooking has finished After 3 hours the Keep Warm feature will shut the oven OFF The Keep Warm feature may be used without any other cooking operations or can be set to turn ON automatically after a BAKE TIME or DELAYED BAKE TIME Keep Warm Tips e Always start with hot food e Do not use the Keep Warm feature to heat cold food e Food in heat safe glass and glass ceramic containers may need higher temperature settings compared to food in regular containers e Avoid repeated openings of the oven it will allow hot air to escape and the food to cool e Aluminum foil may be used to cover food to increase moisture content To set Keep Warm 1 Arrange interior oven racks and place food in oven 2 Press KEEP WARM HLd will appear in the display Note If no pad is touched within 25 seconds the request to turn ON Keep Warm feature will be cancelled Press START The oven icon will appear in the display 4 To turn OFF the KE
29. when the door is opened or closed CAUTION REMOVE ALL OVEN RACKS and parts before starting a self clean cycle If the oven racks are left in the oven during the self clean cycle the glide ability of the Effortless Oven Rack system will be damaged and will cause all oven racks to loose their shiny finish and or turn blue Remove ALL oven racks and clean according to instructions provided in the Care amp Cleaning section of this manual Make sure the oven and oven racks are COMPLETELY cooled and safe to touch before attempting to assemble or disassemble the Effortless Oven Rack system Never pick up hot oven rack parts 18 Door Rack connector connector bracket bracket LE Connector arm Tig Pai rack Ds fa Sy DZ Sg connector arm KA OS a n oven door Ope Figure 3 Assembly of the Effortless oven rack Left and right door connector brackets with connector arm ends shown in locked position pointing upwards Figure 6 Effortless oven rack after assembly Control pad features SETTING OVEN CONTROLS READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE OVEN For satisfactory use of your oven become familiar with the various features and functions of the oven as described below Detailed instructions for each feature and function follow later in this Use amp Care Guide Qe 2 ke start time set timer clock off Q 7 self convect add chi pizza nuggets clean con
30. with a default temperature of 550 F Broiling Tips e For optimum browning preheat the broil element for 5 minutes e Broil one side until the food is browned turn and cook on the second side Season and serve e Always pull the rack out to the stop position before turning or removing food e Always use the broiler pan and its cover when broiling It allows the dripping grease to be kept away from the high heat of the broil element see Figure 2 e For best broiling results broil with the oven door in the broil stop position see Figure 1 e If using a Searing Grill available by mail order preheat the grill for 5 to 10 minutes before placing your meat e DO NOT use the broil pan without the insert DO NOT cover the broil pan insert with foil The exposed grease could catch fire Accessories available via the enclosed brochure Broiler Insert SF Broiler Pan Pan amp Insert Figure 3 Electric Oven Broilin Recommendations To set a Broil of 500 F 1 Place the broiler pan insert on the broiler pan Then place the food on the broiler pan insert DO NOT use the broiler pan without the insert DO NOT cover the broiler insert with foil The exposed grease could ignite Arrange the interior oven rack Press BROIL 550 will appear in the display Press 5 O O If a lower broil temperature is desired minimum
31. 9 Large 3 piece oven door handle 20 Full width oven door with window 21 Warm amp serve drawer 22 7 single radiant element 23 Keep warm radiant element 24 5 7 double radiant element 25 Bridge radiant element 26 7 single radiant element 27 9 single radiant element 28 Ceramic glass cooktop amp NOTE The features shown for your appliance may vary according to model type amp color BEFORE SETTING SURFACE CONTROLS About the ceramic glass cooktop The ceramic cooktop has radiant surface elements located below the surface of the glass The design of the ceramic cooktop outlines the area of the surface element underneath Be sure to match the pan size with the diameter of the element outline on the cooktop and only flat bottom cookware should be used The type and size of cookware the number of surface elements in use and their settings are all factors that will affect the amount of heat that will spread to areas beyond the surface elements The areas surrounding the elements may become hot enough to cause burns About the radiant surface elements The element temperature rises gradually and evenly As the temperature rises the element will glow red To maintain the selected setting the element will cycle on and off The heating element retains enough heat to provide a uniform and consistent heat during the off cycle For efficient cooking turn off the element several minutes b
32. CKS and ANY ACCESSORIES If the oven racks are not removed they will lose their special coating properties and will no longer slide in and out of the oven cavity effortlessly e Remove any excessive spillovers in the oven cavity before starting the Self Cleaning cycle To clean use hot soapy water and a cloth Large spillovers can cause heavy smoke or fire when subjected to high temperatures DO NOT allow food spills with a high sugar or acid content such as milk tomatoes sauerkraut fruit juices or pie filling to remain on the surface as they may leave a dull spot even after cleaning e Clean any soil from the oven frame the door liner outside the oven door gasket and the small area at the front center of the oven bottom These areas heat sufficiently to burn soil on Clean with soap and water ai D s Ta aN CLS Y gu S T Z H Re NN j _ DO HAND N CLEAN FRAME DO NOT HAND CLEAN OVEN DOOR GASKET DO HAND CLEAN DOOR a NI vq At rq SS ea AW ee Y ae See SETTING OVEN CONTROLS What to Expect during Cleaning While the oven is in operation the oven heats to temperatures much higher than those used in normal cooking Sounds of metal expansion and contraction are normal Odor is also normal as the food soil is being removed Smoke may appear through the oven vent If heavy spillovers are not wiped up before cleaning they may flame and cause more s
33. CL will appear in the display as soon as the door is locked 4 Assoonas the control is set the motor driven oven door lock will begin to close automatically Once the door has been locked the DOOR and icon indicator light will quit flashing and remain on 5 Press DELAY START Enter the desired start time using the number pads 4 3 0 6 Press START DELAY DOOR and icon icons will remain on 7 The control will start the self cleaning at the set start time for the period of time previously selected At that time the icon DELAY will go out CLn and oven icon will appear in the display When the Self Clean Cycle is Completed 1 HOT will appear in the display The time of day the DOOR and icon will remain in the display 2 Once the oven has cooled down for approximately 1 HOUR door OPn will appear and the DOOR and icon will flash until the door is unlocked the oven door can then be opened and the timer will revert back to the time of the day Stopping or Interrupting a Self Cleaning Cycle If it becomes necessary to stop or interrupt a self cleaning cycle due to excessive smoke or fire in the oven 1 Press CANCEL 2 The oven door can only be opened after the oven has cooled down for approximately 1 HOUR door OPn will appear and the DOOR and A icon will flash until the door is unlocked the oven door can then be opened and the timer will revert ba
34. CURRENCE Range is not level Cannot move appliance easily Appliance must be accessible for service Entire range or oven does not operate Cooktop control displays any E code error Models B amp C only ex E014 Oven control beeps and displays any F code error ex F11 Oven light does not work Surface unit does not heat Surface units too hot or not hot enough Drip bowls are pitting or rusting Drip bowls turning color or distorted out of shape Metalmarks 42 POSSIBLE CAUSE SOLUTION Poor installation Place oven rack in center of oven Place a level on the oven rack Adjust leveling legs at base of range until the rack is level When range is level cooktop may appear out of alignment if countertop is not level Weak unstable floor Be sure floor is level and can adequately support range If floor is sagging or slopping contact a carpenter to correct the situation Kitchen cabinet misalignment may make range appear to be unlevel Be sure cabinets are square and have sufficient room for range clearance Cabinets not square or are built in too tight Contact a cabinet maker to correct the problem Contact builder or installer to make appliance accessible Carpet interferes with range Provide sufficient space so range can be lifted over carpet Gas line is hard plumbed Have a flexible C S A international approved metal appliance connector installed Make sure cord plug is plugged tightly
35. EP WARM at any time press CANCEL ag To set Keep Warm to turn ON automatically 1 Arrange interior oven racks and place food in oven Set the oven properly for Bake Time or Delayed Bake Time See their respective sections for more details 2 Press KEEP WARM Note If no pad is touched within 25 seconds the request to turn ON Keep Warm feature will be cleared 3 Press START HLd will disappear and the temperature will be displayed The Keep Warm mode is set to turn ON automatically after Timed Bake has finished 4 To turn the Keep Warm feature OFF at any time press CANCEL amp NOTE Pressing CANCEL will stop the feature at any time 28 SETTING PIZZA some models The PIZZA pad has been designed to give optimum cooking performance when cooking your favorite pizza The Pizza pad let you choose a preset between a frozen pizza 425 F and a fresh pizza 400 F If needed a different target temperature than the presets can be entered Some fresh pizza request using a broil feature for a few minutes but this is not part of the Pizza pad presets Pizza Tips e Follow the instructions on the box for preheating and baking times e For optimum cooking results only bake one pizza at once on rack position 2 e Check the pizza at 75 of the maximum cook time listed on the package To set Pizza for a frozen pizza 1 Arrange interior oven racks 2 Press PIZZA pad Fro will appear in the display
36. FRIGIDAIRE Use amp Care TABLE OF CONTENTS Welcome amp Congratulations cscssessssssaseesscnrarees Important Safety InstructionS s s sssssnsnenerenernnns Features at a GlanCe 2u naannana neeaae Before Setting Surface Controls sccccsssseerseseres Setting Surface Controls s amen Before Setting Oven Controls s cccsssscsrsesereesares SENC OVEN Soni ro kA 17 Setting Keep Warm Drawer Control If equipped 35 Care amp Cleaning Cleaning Chart ccsceccseeeee 36 Care amp Cleaning aaaea ese eese ee eye eee 37 Before You Call reemer eea 40 Major Appliance Warranty ccscescsseserest et neenenn 44 www frigidaire com USA 1 800 944 9044 www frigidaire ca Canada 1 800 265 8352 g Ade ZTOZ Menga SZ8SOZ8TE WELCOME amp CONGRATULATIONS Product Registration Register Your Product S s The PRODUCT REGISTRATION CARD should be filled in completely signed and returned to Electrolux Home Products Serial Plate Location Please record your model and serial numbers below for future reference Model Number Serial Number Purchase Date 2012 Electrolux Major Appliances All rights reserved Printed in Canada 2 Congratulations on your purchase of a new appliance At Electrolux Home Products we are very proud of our product and are completely committed to providing you with the best service possible Your satisfaction is our
37. NVECTION BAKE CONVECTION ROAST and PIZZA amp NOTE The lowest temperature that can be displayed is 100 F 19 SETTING OVEN CONTROLS MINIMUM AND MAXIMUM CONTROL PAD SETTINGS All of the features listed below have minimum and maximum time or temperature settings that may be entered into the control An ENTRY acceptance beep will sound each time a control pad is touched the acceptance beep on the Oven Lockout pad is delayed 3 seconds An ENTRY ERROR tone 3 short beeps will sound if the entry of the temperature or time is below the minimum or above the maximum settings for the feature FEATURE MINIMUM TEMP TIME MAXIMUM TEMP TIME PREHEAT 170 F 77 C 550 F 288 C BAKE 170 F 77 C 550 F 288 C BROIL 400 F 205 C 550 F 288 C CONVECTION BAKE 170 F 77 C 550 F 288 C CONVECTION ROAST 170 F 77 C 550 F 288 C CONVECTION BROIL 400 F 205 C 550 F 288 C PIZZA 170 F 77 C 550 F 288 C CHICKEN NUGGETS 170 F 77 C 550 F 288 C TIMER 12 Hr Mode 0 01 Min 11 59 Hr Min 24 Hr Mode 0 01 Min 11 59 Hr Min CLOCK TIME 12 Hr Mode 1 00 Hr Min 12 59 Hr Min 24 Hr Mode 0 00 Hr Min 23 59 Hr Min DELAY START 12 Hr Mode 1 00 Hr Min 12 59 Hr Min 24 Hr Mode 0 00 Hr Min 23 59 Hr Min BAKE TIME 12 Hr Mode 0 01 Min 5 59 Hr Min 24 Hr Mode 0 01 Min 5 59 Hr Min SELF CLEAN TIME 2 hours 4 hours SETTING THE CLOCK The SET CLOCK pad is used to set the clock The clock may be set for 12 or 24 hour time of da
38. Porcelain enamel coating must be smooth to avoid scratching ceramic cooktops Glass Slow heat conductor Not recommended for ceramic cooktop surfaces because it may scratch the glass amp NOTE Due to the high intensity of heat generated by the surface elements the glass surface will turn green when the element will be turned off This phenomenon is normal and the glass will come back to its original white color after it has completely cooled down White glass cooktops only 11 SETTING SURFACE CONTROLS Single radiant surface elements all models The cooktop has 2 or 3 SINGLE radiant surface elements the left rear position Figures 1 2 amp 3 the right rear position Figures 1 and 2 and the right front position Figures 1 and 3 The left rear element may also be used with the Bridge element Model C only Figure 3 To Operate the Single Radiant Surface Elements 1 Place correctly sized cookware on the radiant surface element 2 Push in and turn the surface control knob in either direction to the desired setting Figure 4 Start most cooking operations on a higher setting and then turn to a lower setting to finish cooking Each surface element provides a constant amount of heat at each setting A glowing red surface heating area extending beyond the bottom edge of the cookware indicates the cookware is too small for the surface heating area 3 When cooking has completed turn the surface control knob to OFF b
39. R TO OPERATING THE OVEN Always use oven mitts when using the oven To remove an oven rack pull the rack forward until it stops Lift up front of rack and slide out To replace an oven rack fit the rack onto the guides on the oven walls Tilt the front of the rack upward and slide the rack back into place Models A amp B shown only Recommended rack positions Food Position Position Models A amp B Model C Broiling meats chicken or fish 4 4 Cookies cakes pies biscuits amp muffins Using a single rack 2or3 2o0r3 Using two racks 2 and 4 2 and 4 Using multiple racks 2 3and 4 2 3 and 4 If equipped with an offset rack 1 3 offset 4 Frozen pies angel food cake yeast bread 1 or 2 casseroles 1 or 2 1 or 2 small cuts of meat or poultry Turkey roast or ham 1 1 Rack positions Models A amp B shown only amp NOTE Always use caution when removing food from the oven BEFORE SETTING OVEN CONTROLS Types of oven racks Your built in range may be equipped with one or more of the oven racks styles shown e Flat handle oven rack All models Figure 1 e Offset oven rack Model A only Figure 2 e Flat oven half rack Models B amp C only Figures 3 amp 4 e Effortless oven rack Models B amp C only Figure 5 Figure 1 All models Figure 2 Model A only Flat handle oven rack Offset oven rack Figure 3 Models B
40. The actual oven temperature and the fan icon will be displayed A beep will sound once the oven temperature reaches 375 F and the display will show 375 CONVECT BAKE and the fan icon 5 Place food in the oven amp NOTE Pressing CANCEL will stop the feature at any time Benefits of Convection Bake Multiple rack baking Some foods cook faster saving time and energy No special pans or bakeware needed amp NOTE The convection fan will start AS SOON AS the oven is set for Convection Bake The display will show an icon of rotating fan within a square This rotating fan icon indicates when the Convection Fan is operating The Bake Broil and Convection elements will also cycle for a better heat distribution SETTING CONVECTION CONVERT The Convection Convert pad is used to automatically convert a standard baking recipe for convection baking When set properly this feature is designed to display the actual converted reduced temperature in the display Convection Convert may ONLY be used with a Convection Bake cooking mode It can be used with the features Delay Start and Bake Time see their sections for directions If convection conversion is used with the Bake Time and Delay Start features CF check food will be displayed when 75 of the bake time complete At this time the oven control will sound 3 long beeps at regular intervals until baking had finished When the bake time has co
41. a HI Gravies Casseroles MED Vegetables Eggs MED Roasts Beef Pork Lamb MED Biscuits Pastries MED Rolls hard MED Rolls soft LO Empty Dinner Plates LO 15 BEFORE SETTING OVEN CONTROLS Oven vent location The oven is vented as shown below When the oven is on warm air is released through the vent This venting is necessary for proper air circulation in the oven and good baking results DO NOT BLOCK OVEN VENT Never close off the openings with aluminium foil or any other material SSS M Model C shown only CAUTION Some models are equipped with a blower which runs in baking and self cleaning mode to keep all internal components at a cool temperature The blower may keep running even if the oven has been turned off until the components have cooled down Air circulation in the oven If using 1 rack place in center of oven If using multiple racks stagger cookware as shown For best air circulation and baking results allow 2 4 5 10 cm around the cookware for proper air circulation and be sure pans and cookware do not touch each other the oven door sides or back of the oven cavity The hot air must circulate around the pans and cookware in the oven for even heat to reach around the food Multiple Oven Racks Arranging oven racks ALWAYS ARRANGE OVEN RACKS WHEN THE OVEN IS COOL PRIO
42. and insert some models in the dishwasher and dry upon removal If soils are not removed follow the cooktop cleaning instructions below Gentle scouring with a soapy scouring pad will remove most spots Rinse with a 1 1 solution of clear water and ammonia If necessary cover difficult spots with an ammonia soaked paper towel for 30 to 40 minutes Rinse with clean water and a damp cloth then scrub with a soap filled scouring pad Rinse and wipe dry with a clean cloth Remove all cleaners or the porcelain may become damaged during future heating DO NOT use spray oven cleaners on the cooktop Your range finish is may be made with Easy Care Stainless Steel some models Clean the stainless with warm soapy water using a clean sponge or cloth Rinse with clean water and dry with a soft clean cloth DO NOT use ANY store bought cleaners like Stainless Steel cleaners or any other types of cleaners containing any abrasive chlorides chlorines or ammonia It is recommended to use mild dish soap and water or a 50 50 solution of water and vinegar Remove racks See To remove and to replace an oven rack under Oven vent s and racks Use a mild abrasive cleaner following manufacturer s instructions Rinse with clean water and dry After cleaning the racks rub the sides of the racks with wax paper or a cloth containing a small amount of baby oil or salad oil this will make the racks glide easier into the rack positions Use soap amp water
43. at is displayed Before adjusting test a recipe by using a temperature setting that is higher or lower than the recommended temperature The baking results should help you to decide how much of an adjustment is needed i NOTE The oven temperature adjustments made with this feature will not change the Self Clean cycle temperature or the Broil temperature To adjust the oven temperature higher 1 Press BAKE for 6 seconds UPO 0 will appear in the display 2 To increase the temperature use the number pads to enter the desired change Example 30 F 3 0 The temperature may be increased as much as 35 F 19 C 3 Press START to accept the temperature change and the display will return to the time of day Press CANCEL to reject the change if necessary To adjust the oven temperature lower 1 Press BAKE for 6 seconds 0 will appear in the display 2 To decrease the temperature use the number pads to enter the desired change Example 30 F 3 0 and then press SELF CLEAN The temperature may be decreased as much as 35 F 19 C 3 Press START to accept the temperature change and the display will return to the time of day Press CANCEL to reject the change if necessary amp NOTE The oven temperature adjustments are permanent and will stay forever in the unit memory unless you manually change it again Even a power outage will not reset these changes Follow the same procedure again if you wish to change it to a differ
44. ch fire Refer to the hood manufacturer s instructions for cleaning e Cleaners Aerosols Always follow the manufacturer s recommended directions for use Be aware that excess residue from cleaners and aerosols may ignite causing damage and or injury e Clean in the self cleaning cycle only the parts of the appliance listed in this Owner s Guide Before using the self cleaning cycle of the appliance remove all utensils stored in the appliance e Do not clean the oven door gasket The door gasket is essential for a good seal Care should be taken not to rub damage or move the gasket e Do not use oven cleaners No oven cleaner or oven liner protective coating of any kind should be used in or around any part of the appliance e Remove oven racks Oven racks color will change if left in the oven during a self cleaning cycle CAUTION The health of some birds is extremely sensitive to the fumes given off during the self clean cycle of any wall oven Move birds to another well ventilated room mA IMPORTANT SAFETY NOTICE The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the state to cause cancer birth defects or other reproductive harm and requires businesses to warn customers of potential exposure to such substances FEATURES AT A GLANCE MODELA Your built in range Features 1 Electronic oven control w
45. ck to the time of the day NOTE Models B amp C only during self clean cycle surface elements can not be used see ESEC Lockout Feature SETTING KEEP WARM DRAWER CONTROL If equipped Keep warm drawer rack positions The rack can be used in 2 ways e Inthe upright position Figure 1 to allow low profile food items to be placed both under and on top of the rack for example rolls or biscuits on top of the rack and a casserole dish underneath e Inthe downward position Figure 2 to allow you to place light weight food items and empty dishware for example rolls or pastries and dinner plates on the rack Set the keep warm drawer rack in either position Figure 2 Operating the keep warm drawer The purpose of the keep warm drawer is to keep hot cooked foods at serving temperature Always start with hot food It is not recommended to heat cold food in the keep warm drawer All food placed in the keep warm drawer should be covered with a lid or aluminum foil to maintain quality Do not use plastic wrap to cover food Plastic may melt onto the drawer and be very difficult to clean Use only utensils and cookware recommended for oven use in the keep warm drawer y Wor Unate i Always use potholders or oven mitts when removing food from the keep warm drawer as cookware and plates will be hot and you can be burned To set the keep warm drawer controls The control and indicator lights for the keep warm drawer features a
46. controls the Lockout feature The Lockout feature automatically locks the cooktop controls the oven door and prevents the oven from being turned on It does not disable the clock Minute Timer or the interior oven lights To activate the Oven Lockout feature 1 Press and hold for 3 seconds 2 After 3 seconds door Loc will appear in the oven control display a beep will sound and DOOR and A will flash in the display Once the oven door is locked the DOOR and indicators will stop flashing and remain on along with the Loc To reactivate normal oven operation 1 Press and hold g for 3 seconds After 3 seconds door OPn will appear and a beep will sound The DOOR and will flash in the display until the oven door has completely unlocked 2 The oven is again fully operational amp NOTE Models B amp C only during lockout feature surface elements can not be used see ESEC Lockout Feature SETTING QUICK OR POWERPLUS PREHEAT Use the preheat feature when using single rack baking to quickly heat the oven to bake temperatures Use this feature only for standard baking A reminder tone will sound indicating when to place the food in the oven When the oven is finished preheating quick preheat will become just like the bake feature and continue to bake until cancelled To set the Preheat temperature for 375 F 1 Arrange the interior oven racks 2 Press PREHEAT 350 will appear in the
47. d Av WARNING Tip Over Hazard e A child or adult can tip the range and be killed P e Verify the anti tip device has been installed to floor or wall e Ensure the anti tip device is re engaged to floor or wall when the range is moved e Do not operate the range without the anti tip device in place and engaged e Failure to follow these instructions can result in death or serious burns to children and adults oO K Range ti as Leveling MP9 E To check if the anti tip bracket is installed properly use both arms and grasp the rear edge of range back Carefully attempt to tilt range forward When properly installed the range should not tilt forward Refer to the anti tip bracket installation instructions supplied with your range for proper installation Anti Tip Bracket Remove all tape and packaging wrap before using the appliance Destroy the carton and plastic bags after unpacking the appliance Never allow children to play with packaging material Do not remove the wiring label and other literature attached to the appliance Do not remove model serial number plate Proper Installation Be sure your appliance is properly installed and grounded by a qualified technician in accordance in the United States with the National Electrical Code ANSI NFPA No 70 latest edition and local code requirements and in Canada with CSA C22 1 PART 1 latest edition and local code requirements Install only per instal
48. dinary household use or used other than in accordance with the provided instructions 8 Service calls to correct the installation of your appliance or to instruct you how to use your appliance 9 Expenses for making the appliance accessible for servicing such as removal of trim cupboards shelves etc which are not a part of the appliance when it is shipped from the factory 10 Service calls to repair or replace appliance light bulbs air filters water filters other consumable or knobs handles or other cosmetic parts 11 Surcharges including but not limited to any after hour weekend or holiday service calls tolls ferry trip charges or mileage expense for service calls to remote areas including the state of Alaska 12 Damages to the finish of appliance or home incurred during installation including but not limited to floors cabinets walls etc 13 Damages caused by services performed by unauthorized service companies use of parts other than genuine Electrolux parts or parts obtained from persons other than authorized service companies or external causes such as abuse misuse inadequate power supply accidents fires or acts of God DISCLAIMER OF IMPLIES WARRANTIES LIMITATION OF REMEDIES Customer s sole and exclusive remedy under this limited warranty shall be product repair or replacement as provided herein Claims based on implied warranties including warranties of merchantability or fitness for particular purpose
49. e selection Recommended keep warm drawer settings table is shown below If a particular food is not listed start with the MED setting If more crispness is desired remove the lid or aluminum foil from the food Most foods can be kept at serving temperatures on the MED setting When a combination of foods are to be kept warm for instance meat with 2 vegetables and rolls use the HI setting To avoid heat loss do not open the keep warm drawer while in use Keep warm drawer recommended food settings table Food Item Setting Bacon Hamburger Patties HI Poultry Pork Chops HI Fried Foods Pizza HI Gravies Casseroles MED Vegetables Eggs MED Roasts Beef Pork Lamb MED Biscuits Pastries MED Rolls hard MED Rolls soft LO Empty Dinner Plates LO 35 CARE amp CLEANING Cleaning Chart Cleaning various parts of your appliance Before cleaning any part of the appliance be sure all controls are turned off and the appliance is COOL REMOVE SPILLOVERS AND HEAVY SOILING AS SOON AS POSSIBLE REGULAR CLEANING WILL REDUCE THE NUMBER OF MAJOR CLEANING LATER Surfaces Aluminum trim pieces amp Vinyl Glass Painted and Plastic Body Parts Control Knobs amp Decorative Trim Pieces Control Panels Porcelain Enamel Burner Grates Cooktop Surface Below Cooktop Broiler Pan amp Insert some models Door Liner Oven Bottom amp Burner Drip Pans Easy Care Stainless Steel some models Oven Door amp Drawer Front
50. easy check to be sure all surface elements are turned off CAUTION Do not place plastic items such as salt and pepper shakers spoon holders or plastic wrappings on cooktop when it Is in use These items could melt or ignite Potholders towels or wooden spoons could catch fire if placed too close to the surface elements CAUTION Do not allow aluminum foil or ANY material that can melt to make contact with the ceramic glass cooktop If these items melt on the cooktop they will damage the ceramic cooktop SETTING SURFACE CONTROLS Figure 3 Model C 0 Figure 4 amp NOTE See Recommended Setting for Surface Element table on page 10 Figure 5 CAUTION Radiant surface elements may appear to have cooled after they have been turned OFF HE Hot Element message Models B amp C or the hot surface indicator light Model A will turn ON and will continue to glow until the glass cooktop has cooled down to a moderate level The glass surface may still be hot and burns may occur if the glass surface is touched before the indicator light has turned OFF The message may remain on even though the controls are turned OFF SETTING SURFACE CONTROLS Bridge surface radiant element Model C only The cooktop is equipped with a BRIDGE surface element located at the left front and middle Fig 1 positions The Bridge can be used when cooking with rectangular like a griddle or oval shaped cookware The eleme
51. ed down for approximately 1 HOUR door OPn will appear and the DOOR and icon will flash until the door is unlocked the oven door can then be opened and the timer will revert back to the time of the day Stopping or Interrupting a Self Cleaning Cycle If it becomes necessary to stop or interrupt a self cleaning cycle due to excessive smoke or fire in the oven 1 Press CANCEL 2 The oven door can only be opened after the oven has cooled down for approximately 1 HOUR door OPn will appear and the DOOR and A icon will flash until the door is unlocked the oven door can then be opened and the timer will revert back to the time of the day 34 The SELF CLEAN and DELAY START pads controls the Delayed Self Clean operation The automatic timer will turn the oven on and off at the time you select in advance To set the control for the Self Cleaning Cycle to start at a delayed time and shut off automatically example 3 hour self clean cycle to start at 4 30 1 Be sure the clock is set with the correct time of day and the oven door is closed 2 Press SELF CLEAN CLn and 3 00 HR will show in the display The control will automatically clean for a 3 hour period amp NOTE If a 2 or 4 hour clean time is desired press SELF CLEAN multiple times to toggle between 2 3 or 4 hours 3 Press START door Loc will appear a beep will sound and the DOOR and icon will flash the letters
52. efore cooking is complete This will allow residual heat to complete the cooking process Element ON amp hot surface indicator lights Your appliance is equipped with two different types of radiant surface control indicator lights that will glow on the backguard the Element On indicator light and the hot surface indicator lights The element ON indicator lights are located on the control panel Figure 1 between the two radiant element control knob and will glow when a surface element is turned ON 0 0 o_ hi j T Si lo il hi d 6 6 N e 2 8 4 4 e e 3 7 2 1 2 f e 4 lo lo on med _ element ON indicator light Figure 1 Element ON indicator light location Model A only The hot surface indicator light located on the cooktop Figure 2 will glow when any surface cooking area heats up and will remain on until the glass cooktop has cooled to a MODERATE level hot surface indicator light Figure 2 Model A only Hot surface indicator light location NOTE Radiant elements have a limiter that allows the element to cycle ON and OFF even at the HI setting This helps to prevent damage to the ceramic smooth top Cycling at the HI setting is normal and can occur if the cookware is too small for the radiant element or if the cookware bottom is not flat Be sure to read detailed instructions for ceramic glass cooktop cleaning in the General Care amp Cleaning section and Before You Call checklist secti
53. efore removing the cookware amp NOTE The surface Element On indicator lights will glow when one or more elements are turned on A quick glance at these indicator lights when cooking is finished is an easy check to be sure all surface elements are turned off amp NOTE See Recommended Setting for Surface Element table on page 10 CAUTION Do not place plastic items such as salt and pepper shakers spoon holders or plastic wrappings on cooktop when it is in use These items could melt or ignite Potholders towels or wooden spoons could catch fire if placed too close to the surface elements CAUTION Do not allow aluminum foil or ANY material that can melt to make contact with the ceramic glass cooktop If these items melt on the cooktop they will damage the ceramic cooktop 12 Figure 1 Model A Figure 2 Model B Figure 3 Model C OFF lo hi S A 2 8 3 7 _ A 4 6 med Figure 4 Control knob shown is typical only CAUTION Radiant surface elements may appear to have cooled after they have been turned OFF HE Hot Element message Models B amp C or the hot surface indicator light Model A will turn ON and will continue to glow until the glass cooktop has cooled down to a moderate level The glass surface may still be hot and burns may occur if the glass surface is touched before the indicator light has turned OFF The message may remain on even though the controls a
54. eheating and baking instructions on the box and only use a single rack e For a single rack use rack position 2 e For multiple racks use rack positions 2 and 4 To set Chicken Nuggets 1 Arrange interior oven racks and place food in oven 2 Press CHICKEN NUGGETS pad CHI will appear inthe display If a different temperature than 400 F is needed enter the temperature now using the keypad digits If a different Bake Time than 18 minutes is required press BAKE TIME and enter the desired time or 0 for an untimed baking 3 Press START The fan icon will appear in the display 4 To turn OFF the Chicken Nuggets feature at any time press CANCEL amp NOTE The Chicken Nuggets feature is automatically programmed to activate the Keep Warm feature when the cooking is finished HLD will be displayed for a maximum of 3 hours See the Keep Warm feature for more information SETTING OVEN CONTROLS SETTING MY FAVORITE some models The My Favorite setting allow you to save your most frequently used or most complex cooking sequence This feature will save the cooking mode the target temperature and the bake time if any The oven can recall a cooking sequences from its internal memory which is easily accessible from a one touch button This function can be used with Bake Convection Bake Convection Roast and Preheat To save a Favorite example is a 450 F Bake for 30 minutes 1 Press BAKE The default tempera
55. either FAhrnht or CELSIUS 3 Press START to accept the change or press CANCEL to reject the change SETTING OVEN CONTROLS SETTING SILENT CONTROL OPERATION The DELAY START and SELF CLEAN pads control the Silent Control operation feature The Silent Control operation feature allows the oven control to be operated without sounds or beeps whenever necessary If desired the control can be programmed for silent operation and later returned to operating with all the normal sounds and beeps To change control from normal sound operation to silent control operation 1 To tell if your range is set for normal or silent operation press and hold DELAY START will appear and DELAY will flash in the display After 6 seconds bEEP On or bEEP OFF will appear in the display 2 Press SELF CLEAN to switch between normal sound operation and silent operation mode The display will show either bEEP On or bEEP OFF Note If bEEP On appears the control will operate with normal sounds and beeps If bEEP OFF appears the control is in the silent operation mode 3 Press START to accept the change or press CANCEL to reject the change Note The control will always beep at the end of a minute timer and will beep when a set temperature has been reached even if the control is set to silent operation 21 SETTING OVEN CONTROLS SETTING MINUTE TIMER The TIMER ON OFF pad controls the Minu
56. element may still be hot enough to cause burns even if it is dark in color Pull up latch with finger ee Oo Jeb Push down latch with finger Right Glide WARNING Electrical Shock Hazard can occur 4 and result in serious injury or death Disconnect appliance from electric power before cleaning and servicing the keep warm drawer BEFORE YOU CALL Solutions to Common Problems Oven baking For best cooking results heat the oven before baking cookies breads cakes pies or pastries etc There is no need to preheat the oven for roasting meat or baking casseroles The cooking times and temperatures needed to bake a product may vary slightly from your previously owned appliance Baking Problems and Solutions Chart Baking Causes Corrections Problems Cookies and biscuits burn on the bottom Cakes too dark on top or bottom Cakes not done in the center Cakes not level Foods not done when cooking time iS Up Cookies and biscuits put into the oven before the preheating time is completed Oven rack overcrowded Dark pan absorbs heat too fast Cakes put into the oven before preheating time is completed Rack position too high or low Oven too hot Oven too hot Incorrect pan size Pan not centered in oven Range not level Pan too close to oven wall or rack overcrowded Pan warped Oven too cool Oven overcrowded Oven door opened too frequently All
57. ent setting 32 OVEN LIGHT The oven is equipped with 2 oven lights The oven lights will turn on automatically when the oven door is opened The oven light may be turned on when the door is closed by using the oven light pad located on the control panel The oven light key will toggle the lights at full intensity To toggle the Oven Lights ON and OFF 1 Press OVEN LIGHT Q The interior oven lights are covered with a glass shield held by a wire holder The glass shield must be in place whenever the oven is in use To change the interior oven lights see Changing the oven light in the Care amp Cleaning section SELF CLEANING A self cleaning oven cleans itself with high temperatures well above normal cooking temperatures which eliminate soils completely or reduces them to a fine powdered ash you can wipe away with a damp cloth A IMPORTANT Adhere to the following cleaning precautions e DO NOT use oven cleaners or oven protective coatings in or around any part of the oven interior DO NOT clean the oven door gasket The woven material of the oven door gasket is essential for a good seal Care should be taken not to rub damage or remove the gasket e DO NOT use any cleaning materials on the oven door gasket Doing so could cause damage Remove the broiler pan and insert all utensils and ANY ALUMINUM FOIL These items cannot withstand high cleaning temperatures and will melt Completely remove ALL OVEN RA
58. es of oven door along the door sides Do not use the oven door handle See Figure 3 2 Holding the oven door at the same angle as the removal position seat the hook of the hinge arm over the roller pins located on each side of the oven door frame See Figure 4 The hook of the hinge arms must be fully seated onto the roller pins 3 Fully open the oven door horizontal with floor See Figure 1 4 Push the door hinge locks up towards and into the oven frame on both left and right oven door hinges See Figure 2 to the locked position 5 Close the oven door Door Hinge locations with oven door fully open Figure 2 Figure 1 CARE amp CLEANING Changing oven light CAUTION Roller Oven door as Be sure the oven is unplugged and all parts are COOL Hinge before replacing the oven light bulb Do not turn ge i l l Arm the oven light on during a self cleaning cycle High Hook temperature will reduce lamp life Figure 3 Figure 4 On some models an interior oven light will turn on automatically when the oven is opened The oven light Special door care instructions Most oven may be turned on when the door is closed by using the doors contain glass that can break oven light switch located on the Electronic Oven control Read the following recommendations The oven light bulb is covered with a glass shield held 1 Do not close the oven door until all the oven racks are in place by a wire holder THIS GLASS SHIELD MUST
59. ith kitchen timer 2 Left front element control 3 Left rear element control 4 Right rear element control 5 6 7 Right front element control Keep warm zone control Element on indicator light 8 Automatic oven door light switch 9 Self clean door latch 10 Oven vent 11 Broil element 12 Self cleaning oven interior 13 Convection bake cooking system 14 Oven interior light with removable cover 15 Adjustable interior oven rack s 16 Large 1 piece oven door handle 17 Full width oven door with window 18 Storage drawer 19 6 single radiant element 20 Keep warm radiant element 21 6 single radiant element 22 6 9 double radiant element 23 12 single radiant element 24 Ceramic glass cooktop 25 Hot surface indicator light amp NOTE The features shown for your appliance may vary according to model type amp color 6 FEATURES AT A GLANCE MODEL B Your built in range Features Electronic oven control with kitchen timer Electronic element control digital displays Keep warm zone control Warm amp serve drawer control Left front element control Left rear element control Right rear element control Right front element control Element on indicator light 0 Cooktop on indicator light eee eee 11 Automatic oven door light switch 12 Self clean door
60. king soda a dry chemical or foam type extinguisher e When heating fat or grease watch it closely Fat or grease may catch fire if allowed to become too hot e Use Only Dry Pot holders Moist or damp pot holders on hot surfaces may result in burns from steam Do not let the pot holders touch hot surface units Do not use a towel or other bulky cloth instead of a pot holder e Do Not Heat Unopened Food Containers Buildup of pressure may cause the container to burst and result in injury e Remove the oven door from any unused appliance if it is to be stored or discarded mA IMPORTANT Do not attempt to operate the appliance during a power failure If the power fails always turn off the unit If the unit is not turned off and the power resumes the appliance will not operate and an error message will be displayed Once the power resumes reset the clock and the oven function CAUTION Electronic controllers can be damaged by cold temperatures When you use your appliance for the first time or if it has not been used for a long period of time make sure that it has been exposed to a temperature above 0 C 32 F for at least 3 hours before connecting it to the power supply IMPORTANT INSTRUCTIONS FOR USING YOUR COOKTOP Know which knob controls each surface heating unit Place pan of food on the element before turning it on and turn the element off before removing the pan Use Proper Pan Size This appliance is equi
61. l scratches do not affect cooking and will become less visible with time Cleaning materials not recommended for ceramic glass cooktop have been used See Cooktop Cleaning Ceramic Glass Cooktop Models section under General Cleaning Cookware with rough bottom has been used Use smooth flat bottomed cookware Boilovers are cooked onto surface Use razor blade scraper to remove soil Cooktop Cleaning Ceramic Glass Cooktop Models section under General Cleaning Mineral deposits from water and food Remove using a ceramic glass cooktop cleaning cream Use cookware with clean dry bottoms Many factors affect baking results Make sure the proper rack position is used Center food in the oven and space pans to allow air to circulate Allow the oven to preheat to the set temperature before placing food in the oven Try adjusting the recipes recommended temperature or baking time If you feel the oven is too hot or cool see Adjusting Your Oven Temperature section in the Electronic Oven Control Guide A cooling fan may automatically turn on and off to cool internal parts It is normal and the fan may continue to run even after oven is turned off Excessive spillovers in oven Set self clean cycle for a longer cleaning time Excessive spillovers in oven This is normal especially for pie spillovers or large amounts of grease on the oven bottom Wipe up excessive spillovers before starting the self clean cycle If flames or excessive s
62. latch 13 Oven vent 14 Broil element 15 Self cleaning oven interior 16 Convection bake cooking system 17 Oven interior light with removable cover 18 Adjustable interior oven rack s 19 Large 1 piece oven door handle 20 Full width oven door with window 21 Warm amp serve drawer with large 1 piece handle 22 6 single radiant element 23 Keep warm radiant element 24 6 single radiant element 25 6 9 double radiant element 26 9 12 double radiant element 27 Ceramic glass cooktop amp NOTE The features shown for your appliance may vary according to model type amp color FEATURES AT A GLANCE MODEL C Your built in range Features Electronic oven control with kitchen timer Left rear burner control Keep warm zone control Warm amp serve drawer control Left front element control Left rear element control Right rear element control Right front element control Element on indicator light 0 Cooktop on indicator light a ee a a a a 11 Automatic oven door light switch 12 Self clean door latch 13 Oven vent 14 2 Oven interior light with removable cover 15 Broil element 16 Self cleaning oven interior 17 Convection bake cooking dual fan system 18 Adjustable interior oven rack s 1
63. lation instructions provided in the literature package for this range Ask your dealer to recommend a qualified technician and an authorized repair service Know how to disconnect the electrical power to the appliance at the circuit breaker or fuse box in case of an emergency User Servicing Do not repair or replace any part of the appliance unless specifically recommended in the manuals All other servicing should be done only by a qualified technician to reduce the risk of personal injury and damage to the appliance Never modify or alter the construction of an appliance by removing leveling legs panels wire covers anti tip brackets screws or any other part of the product WARNING Stepping leaning sitting or pulling down on the door or the drawer of this appliance can result in serious injuries and also cause damage to the appliance Do not allow children to climb or play around the appliance The weight of a child on an open door may cause the appliance to tip resulting in serious burns or other injury An open drawer when hot may cause burns 44 WARNING Do not use the oven or warm amp serve drawer if equipped for storage Storage in or on Appliance Flammable materials should not be stored in an oven near surface burners or in the warm amp serve drawer if equipped This includes paper plastic and cloth items such as cookbooks plastic ware and towels as well as flammable liquids Do not store explosive
64. lowed to stand in on bowls will cause corrosion Remove and wash drip bowls as soon as possible after spillover Normal environment Houses along sea coast are exposed to salt air Protect bowls as much as possible from direct exposure to salt air Bottom surface of cookware extends beyond surface elements and touches cooktop surface This can cause high enough temperatures to discolor the drip bowls DO NOT use cookware of this type Pan sizes should be matched to the size of the element Replacement drip bowls may be purchased from your dealer Sliding or scraping of metal utensils on cooktop surface Do not slide metal utensils on cooktop surface Use a ceramic glass cooktop cleaning cream to remove the marks Cooktop Cleaning Ceramic Glass Cooktop Models section under General Cleaning OCCURRENCE Scratches or abrasions on cooktop surface Brown streaks or specks Areas of discoloration with metallic sheen Poor baking results Fan noise during cooking operation Flames inside oven or smoking from vent Oven smokes excessively during broiling Self cleaning cycle does not work Soil not completely removed after self cleaning cycle Excessive smoking from oven vent BEFORE YOU CALL Solutions to Common Problems POSSIBLE CAUSE SOLUTION Coarse particles such as salt or sand between cooktop and utensils can cause scratches Be sure cooktop surface and bottoms of utensils are clean before usage Smal
65. moke and odor than usual This is normal and safe and should not cause alarm If available use an exhaust fan during the self cleaning cycle CAUTION To avoid possible burns use care when opening the oven door after the Self Cleaning cycle Stand to the side of the oven when opening the door to allow hot air or steam to escape During the Self Cleaning cycle the outside of the range can become very hot to the touch DO NOT leave small children unattended near the appliance The health of some birds is extremely sensitive to the fumes given off during the Self Cleaning cycle of any range Move birds to another well ventilated room DO NOT line the oven walls racks bottom or any other part of the range with aluminum foil Doing so will destroy heat distribution produce poor baking results and cause permanent damage to the oven interior aluminum foil will melt to the interior surface of the oven DO NOT force the oven door open This can damage the automatic door locking system Use caution when opening the door after the Self Cleaning cycle is completed The oven may still be VERY HOT amp NOTE See additional cleaning information for the oven door in the General Care amp Cleaning section 33 SETTING OVEN CONTROLS SETTING SELF CLEAN CYCLE TIME LENGTH The SELF CLEAN pad controls the Self Cleaning feature If you are planning to use the oven directly after a self clean cycle remember to allow time for the oven to
66. moke are present stop the self clean cycle and follow the steps under Stopping or Interrupting the Self Cleaning Cycle in the Electronic Oven Control Guide Control s not set properly Follow instructions under Setting Oven Controls Make sure oven is opened to Broil Stop Position Meat too close to the element Reposition the rack to provide proper clearance between the meat and the element Preheat broil element Preheat broil element for searing Grid on broiler pan wrong side up and grease not draining Always place grid on the broiler pan with ribs up and slots down to allow grease to drip into pan Grease has built up on oven surfaces Regular cleaning is necessary when broiling frequently Old grease or food spatters cause excessive smoking Control s not set properly Follow instructions under Oven Cleaning in the Electronic Oven Control Guide Control s not set properly Follow instructions under Oven Cleaning in the Electronic Oven Control Guide Self cleaning cycle was interrupted Stop time must be 2 to 4 hours past the start time Follow steps under Stopping or Interrupting the Self Cleaning Cycle in the Electronic Oven Control Guide Set Self Clean cycle for a longer cleaning time Failure to clean bottom front top of oven or door areas outside oven seal These areas are not in the Self Cleaning area but get hot enough to burn on food residue Clean these areas before starting the Self Clean cycle Burned on
67. mpletely finished the control will display End and beep at regular interval until the CANCEL pad is pressed amp NOTE To use this feature with the BAKE TIME option the BAKE TIME pad must be pressed before the CONVECTION CONVERT pad To set the oven for Convection Bake with a standard baking recipe temperature of 400 F 1 Arrange interior oven racks 2 Press CONVECT CONVECT and BAKE will flash and 350 will appear in the display 3 Press400 CONVECT and BAKE will keep flashing and 400 will appear in the display 4 Press CONVECTION CONVERT As soon as the convection convert pad is pressed the oven will start heating The temperature displayed will be 25 F lower than what it used to be The actual oven temperature and the fan icon will be displayed A beep will sound once the oven temperature reaches 375 F and the display will show 375 CONVECT BAKE and the fan icon 5 Place food in the oven amp NOTE When using a Bake Time under 20 minutes the Convection Convert will not beep and display the CF message SETTING OVEN CONTROLS SETTING CONVECTION ROAST This mode is best for cooking tender cuts of beef lamb park and poultry Use this mode when cooking speed is desired The Convection Roasting gently browns the exterior and seals in the juices Convection roasting uses the hidden bake element the hidden convection element the broil element
68. ne OFF The keep warm zone indicator light will turn OFF keep warm zone E hi 3 hi O hi ne A mi Si med med O med med E m m B m low m low w low lwa V Figure 1 Figure 2 Figure 3 a on off E Figure 4 SETTING SURFACE CONTROLS CAUTION The keep warm zone will not glow red when it is hot but becomes hot enough to cause burns Avoid placing hands on or near the keep warm zone until the keep warm zone hot surface indicator light is OFF Always use potholders or oven mitts when removing food from the keep warm zone as cookware and plates will be hot CAUTION Do not place plastic items such as salt and pepper shakers spoon holders or plastic wrappings on cooktop when it Is in use These items could melt or ignite Potholders towels or wooden spoons could catch fire if placed too close to the surface elements Do not allow aluminum foil or ANY material that can melt to make contact with the ceramic glass cooktop If these items melt on the cooktop they will damage the ceramic cooktop Keep warm zone temperature selection Refer to the keep warm zone table for recommended heating levels If a particular food is not listed start with the medium level and adjust as needed Most foods can be kept at serving temperatures by using the medium level Keep warm zone recommended food settings table Food Item Setting Bacon HI Hamburger Patties HI Poultry Pork Chops HI Fried Foods Pizz
69. neness 1st side 2nd side 6 00 4 00 Rare 7 00 5 00 Medium 8 00 6 00 Well 20 00 10 00 Well 8 00 6 00 Well 13 00 Well 5 00 Well 9 00 7 00 Medium 10 00 8 00 Well SETTING THE SABBATH FEATURE for use on the Jewish Sabbath amp Holidays The BAKE TIME and DELAY START pads are used to set the Sabbath feature The Sabbath feature may only be used with the BAKE pad The oven temperature may be set higher or lower after setting the Sabbath feature the oven temperature adjustment feature should be used only during Jewish Holidays however the display will not visibly show or provide any audible tones indicating whether the change occurred correctly Once the oven is properly set using Bake with the Sabbath feature active the oven will remain continuously ON until cancelled This will override the factory preset 6 Hour Energy Saving feature If the oven light will be needed during the Sabbath press OVEN LIGHT before activating the Sabbath feature Once the oven light is turned ON and the Sabbath feature is active the oven light will remain ON until the Sabbath feature is turned OFF If the oven light needs to be OFF be sure to turn the oven light OFF before activating the Sabbath feature To Program the Oven to Begin Baking Immediately amp activate the Sabbath feature example baking at 350 F 1 Be sure that the clock is set with the correct time of day 2 Place the food in the oven 3 Press BAKE 350 appears in the
70. nt will maintain an even temperature setting across both portions of the Bridge If needed for normal cookware the Bridge element can work like a single element without the Bridge Fig 4 The symbol indicates that only the front potion will heat Fig 2 The A symbol indicates that both front and middle portions will heat Fig 3 You may switch from either coil setting at any time during cooking To Operate the Bridge Surface Element 1 Place correctly sized cookware on the Bridge surface element 2 Push in and turn the control knob as shown in Figure 2 to heat the front portion of the Bridge element for normal shaped cookware or in Figure 3 for larger or rectangular shaped cookware Turn the knob to adjust the setting if needed Start most cooking operations on a higher setting and then turn to a lower setting to finish cooking Each surface element provides a constant amount of heat at each setting A glowing red surface heating area extending beyond the bottom edge of the cookware indicates the cookware is too small Please note that not all cookware will fit the Bridge element correctly 3 When cooking has completed turn the surface control knob to OFF before removing the cookware The BRIDGE element may also be used in combination with the left rear single element Fig 6 Because these elements have 2 different controls one element can be used to cook while the other element may be used to keep food warm CAUTION
71. od to be prepared and the size of i the surface element e Made of a material that conducts heat well Easy to clean Always match pot diameter i B to element surface diameter Figure 2 INCORRECT e Curved and warped pan bottoms k sen Pan overhangs element by more than one half inch k gt le e Pan is smaller than element i e Heavy handle tilts pan Figure 1 Figure 2 Cookware material types The cookware material determines how evenly and quickly heat is transferred from the surface element to the pan bottom The most popular materials available are Aluminum Excellent heat conductor Some types of food will cause it to darken Anodized aluminum cookware resists staining amp pitting If aluminum pans slide across the ceramic glass cooktop they may leave metal marks which will resemble scratches Remove these marks immediately Copper Excellent heat conductor but discolors easily May leave metal marks on ceramic glass see Aluminum above Stainless steel Slow heat conductor with uneven cooking results Is durable easy to clean and resists staining Cast iron A poor heat conductor however will retain heat very well Cooks evenly once cooking temperature is reached Not recommended for use on ceramic cooktops Porcelain enamel on metal Heating characteristics will vary depending on base material
72. on of this Use and Care Guide BEFORE SETTING SURFACE CONTROLS The electronic surface element control ESEC Models B amp C only The Electronic Surface Element Control ESEC feature includes digital display windows The ESEC feature provides a numeric digital setting for the radiant surface element positions on the cooktop These settings work the same way as normal knob setting indicators work except the settings are displayed in digital windows The available ESEC display settings The ESEC control provides various heat levels from Hi Figure 2 to Lo Figure 5 and OFF Figure 1 The settings between 3 0 and 9 5 increase or decrease in increments of 5 1 2 The settings between 1 2 and 3 0 are Simmer settings which decrease or increase in increments of 2 1 5 to Lo Figure 5 lowest Simmer setting for more precise settings at lower heat levels Use the Recommended Surface Setting Chart to determine the correct setting for the kind of food you are preparing ESEC power failure indicator message PF When the range is first plugged in or when the power supply to the range has been interrupted the ESEC control will display the message PF Power Failure Figure 6 After a few seconds the PF message will disappear from the display ESEC hot element indicator message HE After using any of the single or dual radiant element positions the cooktop will become very hot Even after turning the control knob to OFF the cook
73. only When your Oven Sabbath feature is ON the Electronic Surface Elements are also in Sabbath mode This means that all electronic surface element control displays show Sb The surface elements can be used even if the Sabbath Feature is on To turn ON a Surface Element when the Oven Sabbath Feature is active If you turn on a surface element when the oven Sabbath feature is on the electronic surface element control will record that request and execute it with a 15 30 seconds delay So the element will start heating 15 30 seconds after the surface element control was turned on As the oven control the surface element display will not show the setting because Sb is on in the displays When necessary it is possible to adjust the power of the surface element but you have to remember that the surface element control will adjust the temperature with the same delay To turn OFF the Surface Element when the Oven Sabbath Mode Is active To shut off the surface element while the Sabbath feature is ON proceed as usual but take note that the element will immediately turn off without any delay SETTING OVEN CONTROLS ADJUSTING OVEN TEMPERATURE The temperature in the oven has been pre set at the factory When first using the oven be sure to follow recipe times and temperatures If you think the oven is cooking too hot or too cool for the temperature you select you can adjust the actual oven temperature to be more or less than wh
74. oose to add a BAKE TIME or DELAY START with most of the functions listed above unless specified in their corresponding section O 2 ke start time set mer on off clock bwerplus keep y bake broil convect preheat warm avorite a a o a o 7 8 9 6 chicken self convect add M19 anl pizza nuggets clean convert a min m 0 o Figure 2 Model C 12 Keep warm pad Use to keep the dishes and food warm until served 13 Pizza pad some models Use to select the pizza cooking feature 14 Chicken nuggets pad Use to select the chicken nuggets cooking feature 15 Self Clean pad Use to select the self cleaning feature 16 Convection convert pad Use to convert a regular recipe temperature to a convection temperature 17 Add a minute pad some models Use to add a minute to the timer feature 18 Numeric pad Use to enter temperatures and times 19 Start pad Use to start all oven features not used with Oven Light 20 Cancel pad Use to cancel any oven feature previously entered except the time of day and minute timer TEMPERATURE VISUAL DISPLAY Your oven is equipped with a temperature visual display When a cooking mode is set the actual temperature will be shown in the display and will rise as the unit preheat When the unit has reached its target temperature a chime will sound to remind you to place the food in the oven This feature will be active with some cooking modes BAKE CO
75. or Delayed Timed Bake or Delayed Timed Convection Bake 12 24 hours in advance set the control for the 24 hour time of day display mode To program the oven for a delayed BAKE start time example baking at 375 F starting at 5 30 1 Be sure that the clock is set with the correct time of day 2 Arrange interior oven rack and place the food in the oven 3 Press BAKE 350 will appear in the display 4 Enter the desired temperature pressing 3 7 5 5 Press START The actual oven temperature will appear in the display 6 Press DELAY START 7 Enter the desired start time pressing 5 3 0 8 Press START When Delayed Time Bake starts the set oven temperature will appear DELAY BAKE and the current time of day will appear in the display amp NOTE If itis desired to have the oven shut off automatically after a set time enter a BAKE TIME at this step 7 When the desired start time is reached the actual oven temperature appears in display and DELAY disappears Oven starts to bake at the previously selected temperature Press CANCEL when baking has completed or at any time to cancel the Delayed Time Bake feature Use caution with the DELAY START features Use the automatic timer when cooking cured or frozen meats and most fruits and vegetables Foods that can easily spoil such as milk eggs fish meat or poultry should be chilled in the refrigerator first Even when chilled they should not stand in
76. ow oven to preheat to the selected temperature before placing food in oven Choose pan sizes that will permit 5 1cm to 10 2cm 2 to 4 of air space on all sides when placed in the oven Use a medium weight aluminum baking sheet Allow oven to preheat to the selected temperature before placing food in the oven Use proper rack position for baking needs Set oven temperature 25 F 12 C lower than recommended Set oven temperature 25 F 12 C lower than recommended Use pan size suggested in recipe Use proper rack position and place pan so there is 5 1cm to 10 2cm 2 to 4 of space on all sides of pan Place a marked glass measuring cup filled with water on the center of the oven rack If the water level is uneven refer to the installation instructions for leveling the range Be sure to allow 5 1cm to 10 2cm 2 to 4 of clearance on all sides of each pan in the oven Do not use pans that are dented or warped Set oven temperature 25 F 12 C higher than suggested and bake for the recommended time Be sure to remove all pans from the oven except the ones to be used for baking Open oven door only after shortest recommended baking time 41 BEFORE YOU CALL Solutions to Common Problems A IMPORTANT Before you call for service review this list It may save you time and expense The list includes common occurrences that are not the result of defective workmanship or materials in this appliance OC
77. pped with one or more surface burners of different sizes Select utensils having flat bottoms large enough to cover the surface unit The use of undersized utensils will expose a portion of surface heating unit to direct contact and may result in ignition of clothing Proper relationship of utensil to the surface will also improve efficiency Utensil Handles Should Be Turned Inward and Should Not Extend Over Adjacent Surface Units To reduce the risk of burns ignition of flammable materials and spillage due to unintentional contact with the utensil The handle of the utensil should be positioned so that it is turned inward and does not extend over adjacent surface unit Do not use Searing Grill on the cooktop The Searing grill is not designed for use on the cooktop Doing so may result in a fire Never Leave Surface Units Unattended Boilovers cause smoking and greasy spillovers that may ignite or a pan that has boiled dry may melt Protective Liners Do not use aluminum foil to line oven bottom or any other part of the appliance Only use aluminum as recommended for baking if used as a cover placed on the food Any other used of protective liners or aluminum foil may result in a risk of electric shock or fire or a short circuit Glazed Cooking Utensils Only certain types of glass glass ceramic ceramic earthenware or other glazed IMPORTANT SAFETY INSTRUCTIONS utensils are suitable for cooktop service without breaking
78. r any slots holes or passages in the oven bottom or cover an entire rack with materials such as aluminum foil Doing so blocks air flow through the oven and may cause carbon monoxide poisoning Aluminum foil linings may trap heat causing a fire hazard e Placement of Oven Warm amp Serve Drawer if equipped Racks Always place oven Warm amp Serve Drawer if equipped racks in desired location while appliance is cool Remove all utensils from the rack before removing rack If rack must be moved while oven is hot use extreme caution Use pot holders and grasp the rack with both hands to reposition Do not let pot holders contact the hot oven element or interior of the oven Warm amp Serve Drawer if equipped Do not use a broiler pan without its insert Broiler pan and grid allow dripping fat to drain and be kept away from the high heat of the broiler Do not cover the broiler grid or oven bottom with aluminum foil Exposed fat and grease could ignite Do not touch a hot oven light bulb with a damp cloth Doing so could cause the bulb to break Disconnect the appliance or shut off the power to the appliance before removing and replacing the bulb IMPORTANT SAFETY INSTRUCTIONS FOR CLEANING YOUR OVEN e Clean the appliance regularly to keep all parts free of grease that could catch fire Exhaust fan ventilation hoods and grease filters should be kept clean Do not allow grease to accumulate Greasy deposits in the fan could cat
79. re located on the control panel The temperatures are approximate and are designated by HI high MED medium and LO low 1 Touch the oneoff pad see Figure 6 at the keep warm drawer control position The keep Warm drawer indicator light will flash Note If no further pads are touched within 25 seconds the request to power the keep warm drawer ON will clear 2 Set the desired power level Touch A once to turn ON the power level for HI see Figure 3 or V to turn ON the power level for LO see Figure 5 The keep warm drawer indicator light located beside the oneoff pad will turn ON steady 3 Each touch of the V or A pads will decrease or increase through 5 power levels from HI see Figure 3 to MED see Figure 4 to LO see Figure 5 Note For best results preheat the keep warm drawer before adding the food An empty drawer will preheat in approximately 15 minutes 4 When the food is ready for removal keep warm touch the oneoff pad once to turn drawer the keep warm drawer OFF The A fh keep warm drawer indicator light will S turn OFF med m hi hi hi y 5 low med med med o E m low E low m low on off Figure 3 Figure 4 Figure 5 Figure 6 amp NOTE The keep warm drawer is inoperable during the self clean cycle The keep warm drawer is equipped with a latch which may require extra force when opening and closing the drawer Keep warm drawer temperatur
80. re turned OFF Dual Surface Radiant Element all models The cooktop is equipped with 1 or 2 dual radiant surface elements located at the left front Figures 1 amp 2 and the right front Figure 2 or the right rear Figure 3 position Symbols around the knob are used to indicate which coil of the dual radiant element will heat The e symbol indicates that only the inner coil will heat Figure 4 The symbol indicates that both inner and outer coils will heat Figure 5 You may switch from either coil setting at any time during cooking To Operate the Dual Surface Element 1 Place correctly sized cookware on the dual surface element 2 Push in and turn the control knob to the inner coil symbol for smaller cookware Figure 4 or to inner and outer coil symbol for larger cookware Figure 5 Turn the knob to adjust the setting if needed Start most cooking operations on a higher setting and then turn to a lower setting to finish cooking Each surface element provides a constant amount of heat at each setting A glowing red surface heating area extending beyond the bottom edge of the cookware indicates the cookware is too small for the surface heating area 3 When cooking has completed turn the surface control knob to OFF before removing the cookware amp NOTE The surface Element On indicator lights will glow when one or more elements are turned on A quick glance at these indicator lights when cooking is finished is an
81. ribed or illustrated are subject to change without notice Canada USA 1 800 265 8352 1 800 944 9044 Electrolux Canada Corp Electrolux Home Products Inc A Ele ctrolux 5855 Terry Fox Way 10200 David Taylor Drive Mississauga Ontario Canada Charlotte NC 28262 L5V 3E4 44
82. s such as aerosol cans on or near the appliance Flammable materials may explode and result in fire or property damage 3 IMPORTANT SAFETY INSTRUCTIONS CAUTION Do not store items of interest to children in the cabinets above the appliance Children climbing on the cooktop to reach items could be seriously injured e Do not leave children alone Children should not be left alone or unattended in the area where an appliance is in use They should never be allowed to sit or stand on any part of the appliance e DO NOT TOUCH SURFACE UNITS AREAS NEAR THESE UNITS OVEN HEATING ELEMENTS OR INTERIOR SURFACES OF THE OVEN OR WARMER DRAWER if equipped Both surface units and oven heating elements may be hot even though they are dark in color Areas near surface units may become hot enough to cause burns During and after use do not touch or let clothing or other flammable materials touch these areas until they have had sufficient time to cool Among these areas are the cooktop surfaces facing the cooktop the oven vent openings and surfaces near these openings oven door and window e Wear Proper Apparel Loose fitting or hanging garments should never be worn while using the appliance Do not let clothing or other flammable materials contact hot surfaces 44 WARNING NEVER use your appliance as a space heater to heat or warm the room e Do Not Use Water or Flour on Grease Fires Smother the fire with a pan lid or use ba
83. ssist in easier access to your food items This feature works whenever the oven door is opened or closed To assemble the Effortless Oven Rack system 1 Locate all required parts You will need the supplied oven rack Effortless Oven Rack is a flat rack with a special dark coating on the left and right rack sides and the 2 supplied chrome connector arms 2 Open the oven door Be sure the oven is completely cool before proceeding 3 Place the oven rack in positions 1 2 or 3 only see previous page to verify positions Be sure the rack connector brackets are at the rear of the range and pointing towards oven bottom See Figure 2 4 Assemble one connector arm at a time With the oven door open and the oven rack in place install one end of the connector arm to the hole in the door connector bracket Figure 1 and the other end in the hole in the rack connector bracket Figure 2 and as in Figure 3 The oven rack may need to be adjusted in or out in the rack position to match the length of the connector arm 5 While holding the connector arm in place twist the connector arm so the ends of the connector arm point upwards See Figures 4 amp 5 The connector arm should now be locked into position 6 Repeat steps 4 and 5 for the other connector arm 7 Once both connector arms are properly in place be sure to test the oven rack operation by gently closing the oven door The oven rack should move in and out of the oven freely
84. te Timer feature The Minute Timer serves as an extra timer in the kitchen that will beep when the set time has run out It does not start or stop cooking The Minute Timer feature can be used during any of the other oven control functions Refer to Minimum and Maximum Control Pad Settings for time amount settings To set the Minute Timer example for 5 minutes 1 Press TIMER ON OFF will appear and Timer will flash in the display 2 Press the number pads to set the desired time in the display 3 Press START The time will begin to count down with 5 00 and Timer will stay in the display Note If START is not pressed the timer will return to the time of day after 25 seconds 4 When the set time has run out End and Timer will show in the display The clock will sound with 3 beeps every 5 seconds until TIMER ON OFF is pressed To cancel the Minute Timer before the set time has run out 1 Press TIMER ON OFF The display will return to the time of day SETTING ADD 1 MINUTE FEATURE some models The ADD 1 MINUTE pad is used to set the Add 1 Minute feature When the ADD 1 MINUTE pad is pressed 1 minute is added to the Minute Timer feature if this feature is already active If the Minute Timer feature is not active and the ADD 1 MINUTE pad is pressed the Minute Timer feature will become active and will begin counting down from 1 minute 22 SETTING LOCKOUT FEATURE The pad
85. to override this feature for Continuous Baking To set the control for Continuous Bake or 6 Hour Energy Saving features Press and hold TIMER for 6 seconds After 6 seconds 6Hr OFF or StAY On will appear in the display and the control will beep once 2 Press SELF CLEAN to switch between the 6 Hour Energy Saving and continuous bake features Note 6Hr OFF in the display indicates the control is set for the 6 Hour Energy Saving mode and StAY On indicates the control is set for the Continuous Bake feature 3 Press START to accept the change display will return to time of day or press CANCEL to reject the change SETTING TEMPERATURE DISPLAY FAHRENHEIT OR CELSIUS The BROIL and SELF CLEAN pads control the Fahrenheit or Celsius temperature display modes The oven control can be programmed to display temperatures in Fahrenheit or Celsius The oven has been preset at the factory to display in Fahrenheit To change display from Fahrenheit to Celsius or Celsius to Fahrenheit 1 Totell if the display is set for Fahrenheit or Celsius press BROIL and hold it for 6 seconds 550 will appear and BROIL will flash in the display and a beep will sound If FAhrnht appears the display is set to show temperatures in Fahrenheit If CELSIUS appears the display is set to show temperatures in Celsius 2 Press SELF CLEAN to switch between Fahrenheit or Celsius display modes The display will show
86. to thoroughly clean the top sides and front of the oven door Rinse well You may use a glass cleaner on the outside glass of the oven door DO NOT immerse the door in water DO NOT spray or allow water or the glass cleaner to enter the door vents DO NOT use oven cleaners cleaning powders or any harsh abrasive cleaning materials on the outside of the oven door DO NOT clean the oven door gasket The oven door gasket is made of a woven material on Self Cleaning models which is essential for a good seal Care should be taken not to rub damage or remove this gasket Ceramic glass cooktop cleaning amp maintenance Consistent and proper cleaning is essential to maintaining your Ceramic glass cooktop g FORMULA IN THE WORLD ono ERAMA BRYTE C COOKTOP CERAM FANER Prior to using your cooktop for the first time apply the recommended CERAMA BRYTE Cleaning Creme to the ceramic surface Clean and buff with a non abrasive cloth or pad This will make cleaning easier when soiled from cooking The special cooktop cleaning cream leaves a protective finish on the glass to help prevent scratches and abrasions A Sliding aluminum or copper clad bottom pans on the cooktop can cause metal markings on the cooktop surface These marks should be removed immediately after the cooktop has cooled using the cooktop cleaning cream Metal marks can become permanent if not removed prior to future use Cookware
87. top will remain hot for some time The ESEC control monitors the temperature of the cooktop and displays the message HE hot element warning when the cooktop is still too hot to touch Figure 4 If the HE message appears in the window the control can still be turned ON again for use ESEC error indicator message Er An error message will be displayed glowing Er at power up or after a power failure if ANY of the surface control knobs were left in the ON positions Figure 7 If a power failure should occur be sure to set all of the surface control knobs to the OFF position This will reset the surface controls Once the surface controls have been set to the OFF positions the surface controls should return to normal operation If the surface controls do not function and the Er message remains in any display after following these procedures contact your authorized servicer for assistance ESEC Lockout Feature The ESEC feature will not operate during a Self Clean cycle or when the Lockout feature is active Whenever the Lockout feature is active will appear in any ESEC digital display windows See Figure 8 to show that all surface elements can not be activated 10 Figure 1 Figure 2 Figure 3 CB hi Figure 4 Figure 5 Control knobs shown are typical only Surface cooking settings Use the chart to determine the correct setting for the type of food you are preparing
88. ture will appear in the display Enter temperature needed 45 0 Press START Press BAKE TIME Enter time needed 3 0 Press START Press and hold for 3 seconds MY FAVORITE pad The v icon will be shown to confirm your setting has been saved ee ae ee iS To recall a Favorite 1 Press MY FAVORITE pad 2 Press START amp NOTE Recalling a Favorite can only be done when the oven is not currently in operation To overwrite a Favorite 1 To overwrite My Favorite simply start a new cooking sequence and save it as shown in example above The new My Favorite settings will overwrite the old ones To delete a Favorite 1 Press the MY FAVORITE pad to delete for 3 seconds while the oven is not in operation and no cooking mode has been set The icon will disappear 29 SETTING OVEN CONTROLS SETTING BROIL This mode is best for meats fish and poultry up to 1 thick Broiling is a method of cooking tender cuts of meat by direct heat under the broil element of the oven The high heat cooks quickly and gives a rich brown outer appearance The BROIL pad controls the Broil feature An optional Searing Grill Broiler Pan and Insert are available via the enclosed accessories brochure Figure 2 amp 3 The optional broil pan and broil pan insert used together allow dripping grease to drain and be kept away from the high heat of the oven broiler The oven can be programmed to broil at any temperature from 400 F to 550 F
89. vection baking there is no need to reduce your oven temperature If your recipe has not had the temperature converted for convection baking you can easily reduce using the Convection Convert feature Please see Convection Convert section on next page for further instruction on temperature conversion e Use tested recipes with times adjusted for convection baking when using this mode Time reductions will vary depending on the amount and type of food to be cooked e When using Convection Bake with a single rack place oven rack in position 2 or 3 If cooking on multiple racks place the oven racks in positions 2 and 4 1 3 offset rack and 4 or 2 3 and 4 if there is no offset rack supplied e Most bakeries except cakes should be baked on pans with no sides or very low sides to allow heated air to circulate around the food e Food baked on pans with a dark finish will cook faster rw ie Se N SS A i SS S Air circulation during Convection Bake Figure 1 24 Oven Rack Positions Figure 2 To setthe oven for Convection Bake and temperature to 375 F 1 Arrange interior oven racks 2 Press CONVECT CONVECT and BAKE will flash and 350 will appear in the display If a Convection Bake of 350 F is needed press START 3 Press375 CONVECT and BAKE will keep flashing and 375 will appear in the display 4 Press START
90. vert a min 10 11 qu keep convect preheat warm 7 8 9 D 20 0 O bake broil Figure 1 Model A amp B 1 Delay start pad Use to program a Delayed Timed Bake or Delay Self Cleaning cycle start time 2 Bake time pad Use to enter the length of the baking time 3 Set clock pad Use to set the time of day 4 Timer on off pad Use to set or cancel the Timer The Timer does not start or stop cooking 5 My favorite pad some models Use to record a temperature setting for a cooking feature 6 Oven light pad Use to turn the oven light ON and OFF 7 Lockout pad Use to lock the oven door and the control panel pads 8 Bake pad Use to select the bake cooking feature 9 Broil pad Use to select the broil cooking feature 10 Convection pad Use to select between the Convection Bake Convection Roast and Convection Broil model B amp C only cooking features 11 Quick preheat or power plus preheat pad Use to quickly raise oven to cooking temperature IMPORTANT THINGS TO KNOW BEFORE SETTING ANY OVEN COOKING FEATURE This appliance has been factory pre set to start any BAKE CONVECTION BAKE CONVECTION ROAST or PREHEAT feature with the oven set temperature automatically set for 350 F The BROIL or CONVECTION BROIL features are pre set at 550 F However if desired the oven set temperature may be adjusted at any time during the cooking process You may also ch
91. y operation The clock has been preset at the factory for the 12 hour operation When the range is first plugged in or when the power supply to the range has been interrupted the timer in the display will flash To set the clock example below for 1 30 1 Press SET CLOCK CLO will appear in the display 2 Press 130 pads to set the time of day to 1 30 CLO will stay in the display 3 Press START CLO will disappear and the clock will Start 20 CHANGING BETWEEN 12 OR 24 HOUR TIME tl DAY DISPLAY Press and hold SET CLOCK for 6 seconds CLO will appear in the display 2 CONTINUE holding the pad until 12HrdAY or 24Hr dAY appears in the display and the control beeps once 3 Press SELF CLEAN to switch between the 12 and 24 hour time of day display The display will show either 12Hr dAY or 24Hr dAY 4 Press START to accept the change or press CANCEL to reject the change Reset the correct time as described in To set the Clock above Please note that if the 24 hour time of day mode was chosen the clock will now display time from 0 00 through 23 59 hours SETTING CONTINUOUS BAKE OR 6 HOUR ENERGY SAVING The TIMER and SELF CLEAN pads control the Continuous Bake or 6 Hour Energy Saving features The oven control has a factory preset built in 6 Hour Energy Saving feature that will shut off the oven if the oven control is left on for more than 6 hours The oven can be programmed

Frigidaire FGES3045KW Range User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents