Friedrich CP24F30 Air Conditioner User Manual
Contents
1. All service calls for explaining the operation of this product will be the sole responsibility of the consumer All warranty service must be provided by an Authorized FRIEDRICH Service Agency unless authorized by FRIEDRICH prior to repairs being made 10 08 4 FRIEDRICH Friedrich Air Conditioning Co 10001 Reunion Place Suite 500 San Antonio TX 78216 1 800 541 6645 www friedrich com 661299038132. remain in to resume operation m Electrical overloading overheating cord pinching or aging can trip Reset button will pop out the power supply cord After correcting the problem press and release RESET listen for click Reset button will latch and remain in to resume operation NOTE A damaged power supply cord must be replaced with a new power supply cord obtained from the product manufacturer and must not be repaired Air conditioner seems to run too much m The current air conditioner replaced an older model The use of more efficient components may cause the air conditioner to run longer than an older model but the total energy consumption will be less Newer air conditioners do not emit the blast of cold air you may be accustomed to from older units but this is not an indication of lesser cooling capacity or efficiency Refer to the efficiency rating EER and capacity rating in BTU hr marked on the air conditioner m The air conditioner is in a heavily occupied room or heat producing appliances are in use in the room Use exhaust vent fans while cooking or bathing and try not to use heat There is excessive heat or moisture open container cooking showers etc in the room Use a fan to exhaust heat or moisture from the room Try not to use heat producing appliances during the hottest part of the day The louvers are blocked Install the air conditioner in a location where the louvers are free from curtain
3. High Fan Speed 13 To raise the temperature Press the plus button to raise the temperature Each time you press or hold the plus button the temperature will go up 1 until it reaches 90 F 32 2 C To lower the temperature Press the minus button to lower the temperature Each time you press or hold the minus button the temperature will go down 1 until it reaches 60 F 15 5 C To set Timer for a 1 to 24 hour delay before air conditioner is turned off air conditioner must be On 1 Press TIMER Indicator light on air conditioner control panel will flash 2 Press the plus or minus button to change the delay time from 1 to 24 hours 3 Press TIMER again or wait 10 seconds Indicator light on air conditioner control panel will remain on To set Timer to turn on air conditioner keeping previous settings 1 Turn off air conditioner 2 Press TIMER Indicator light on air conditioner control panel will flash 3 Press the plus or minus button to change delay time 1 to 24 hours 4 Press TIMER again or wait 10 seconds Indicator light on air conditioner control panel will remain on To set Timer to turn on air conditioner changing the previous settings 1 Turn on air conditioner Adjust Mode to Cool Fan Only or Power Saver Adjust Fan Speed to High Medium or Low Adjust temperature between 60 F 15 5 C and 90 F 32 2 C Turn off air conditioner Press TIMER Indicator light on air
4. asleep or away from home since the fan does not circulate the room air continuously Use Low Cool Medium Cool or High Cool for your best comfort m The air conditioner is not properly sized for your room Check the cooling capabilities of your room air conditioner Room air conditioners are not designed to cool multiple rooms The filter is dirty or obstructed by debris Clean the filter The inside evaporator and outside condenser coils are dirty or obstructed by debris See Annual Maintenance Power Saver mode or after you turn off the unit a lower temperature reading than the actual room temperature may be displayed for a short period of time This lower temperature reading is caused by the temperature sensor being located close to the cold evaporator coil The actual room temperature will display within a few minutes Water drips from cabinet into your house m The air conditioner is not properly leveled The air conditioner should slope slightly downward toward the outside Level the air conditioner to provide a downward slope toward the outside to ensure proper drainage See the Installation Instructions NOTE Do not drill a hole into the bottom of the metal base and condensate pan Assistance or Service For assistance service or replacement parts For further assistance For service assistance or to locate factory authorized parts If you need further assistance you can write us at call our Customer Service Ce
5. conditioner control panel will flash 7 Press the plus or minus button to change delay time 1 to 24 hours 8 Press TIMER again or wait 10 seconds Indicator light on air conditioner control panel will remain on ne eN Air Conditioner Care Your new air conditioner is designed to give you many years of dependable service This section tells you how to clean and care for your air conditioner properly Call your local authorized dealer for an annual checkup Remember the cost of this service call is your responsibility Cleaning the Air Filter The air filter is removable for easy cleaning A clean filter helps remove dust lint and other particles from the air and is important for best cooling and operating efficiency Check the filter every 2 weeks to see whether it needs cleaning NOTE Do not operate the air conditioner without the filter in place 1 Turn off air conditioner 2 Remove filter from unit 3 Use a vacuum cleaner to clean air filter If air filter is very dirty wash it in warm water with a mild detergent Do not wash air filter in the dishwasher or use any chemical cleaners Air dry filter completely before replacing to ensure maximum efficiency 4 Slide air filter down into the filter door Close filter door Cleaning the Front Panel 1 Turn off air conditioner 2 Remove the air filter and clean it separately See Cleaning the Air Filter 3 Wipe the front panel with a soft da
6. drill a starter hole through the hole in the curtain housing and into the lower window sash Front View Top View A Left hand curtain B Window channel C 10 x 34 round head screw 2 Insert one of the 10 x 34 round head screws through the threaded hole in the top of the curtain A NE lt e A 10 x 3 round head screw 3 Repeat for right hand curtain Attach Support Brackets A Align holes in cabinet with holes in support bracket B 10 x 72 1 Complete Installation 1 Insert seal behind the top of the lower window sash and against the glass of the upper window B 2 Place one window lock bracket on top of lower window and against upper window sash on each side of window A 3 Use a 2 drill bit to drill a starter holes through the holes in each bracket into the window sash 4 Attach both window lock brackets to window sash with 10 x 4 round head screws to secure window in place A Window lock brackets B Window rail seal C Upper window glass Through the Wall Cabinet Installation 2 Using 10 x pan head Phillips screws attach bracket to cabinet Repeat for other bracket 3 Loosen locking nut and turn the adjustment bolt C for each bracket until the bolt touches the wall B 4 Tighten the locking nut on adjustment bolt to lock in position C A Support bracket B Locking nut C Adjustment bolt NOTES m Handle air conditioner gently m Be sure your ai
7. in workmanship or material within sixty months from date of purchase FRIEDRICH will pay a labor allowance and parts necessary to repair the Sealed Refrigeration System PROVIDED FRIEDRICH will not pay the cost of diagnosis of the problem removal freight charges and transportation of the air conditioner to and from the Service Agency and the reinstallation charges associated with repair of the Sealed Refrigeration System All such cost will be the sole responsibility of the owner This remedy is expressly agreed to be the exclusive remedy within sixty months from the date of the original purchase APPLICABILITY AND LIMITATIONS This warranty is applicable only to units retained within the Fifty States of the U S A District of Columbia and Canada This warranty is not applicable to 1 Air filters or fuses 2 Products on which the model and serial numbers have been removed 3 Products which have defects or damage which results from improper installation wiring electrical current characteristics or maintenance or caused by accident misuse or abuse fire flood alterations and or misapplication of the product and or units installed in a corrosive atmosphere default or delay in performance caused by war government restrictions or restraints strikes material shortages beyond the control of FRIEDRICH or acts of God OBTAINING WARRANTY PERFORMANCE Service will be provided by the FRIEDRICH Authorized Dealer or Service Organization in your a
8. the unit is turned on it will display the previous settings for the Mode Fan Speed and temperature Choose mode See Mode Choose fan speed See Fan Speed Choose temperature See Temperature Mode Press and hold MODE Choose Cool or Fan mode m Cool Cools room Press FAN SPEED to choose fan speed Then adjust the temperature by pressing the up or down arrow buttons E Fan Operates the fan at High speed without cooling The display shows FO fan only Money Savers mM Money Saver Cycles fan with compressor when room temperature reaches the temperature setting on the thermostat Cool Mone Fan Only Fan Speed NOTE The Fan Speed button will operate when the Cool Money Saver or Fan Only mode has been selected 1 2 Press the Fan Speed button until you see the indicator light for the desired setting Choose Low Medium or High O High O Med Fan Speed O Low 12 Temperature Press or press and hold the plus button to raise the temperature 1 until it reaches 90 F 32 2 C Temp Hour Press or press and hold the minus button to lower the temperature 1 until it reaches 60 F 15 5 C Timer Delay To set the Timer for a 1 to 24 hour delay until the air conditioner turns off the air conditioner must be On 1 Press TIMER Indicator light will flash O Timer 2 Press the plus or minus button to change the delay time f
9. Installation and Operation Manual 4 FRIEDRICH Compact Programmable Room Air Conditioner with remote control CP15F10A CP18F30 CP24F30 6612990381 3 11 10 N X Please register your air conditioner Whenever you call to request service on your appliance you will need to provide your complete model number and serial number You can find this information on the model and serial number label Please record model and serial number information below MODEL NUMBER SERIAL NUMBER PURCHASE DATE Table of Contents AVE CONGIRIONG AM een 1 Installation Requirements sacra a a a a OON 3 MOOS An Ee i o E EEEE EEEE EA e ee 3 Bo aE aera UN ein E o aii EN EE O E NT ronan nye er 3 Electrical Reguiremen see i 4 Installation Wa oa of q U1 0 0 9 perenne a eto se ad erase aia dede 6 Unpack DI Serasa a diia 6 Window Installation some MI een A 7 Throusn the Wall Cabine Install ones 9 Complete Tastallati n astas 10 Na AA A O A es eee ET 11 Starting Your Ai Conditioner Digital Control A e 12 Remote Ae OM trl Mel All OMe nl etico ee 13 A RR ON 13 a A A ee A ce 14 Elsanme the Alt Hiller een ee 14 Gleanine the Bronf Parc En ea ot ltd nilo dao co ici 14 Reparrine Rat Dimas a a o la SEE 14 Annual Maintenance A I a eee 14 TrOuBLesho0HNng to ul 14 ASSISTANCE di adoi 15 A ea ee re ace eer ck ea ae ae Na at es se 16 General Instructions This Installation and Operation Manual has been designed to insure maximum sa
10. attach front of panel to chassis ES ANUN A ANNAN A AN AN KU IN ANN Y ANN 6 Reinstall filter and replace front grille NOTE For through the wall installations if needed install molding around room side of cabinet A WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet Do not remove ground prong Do not use an adapter Do not use an extension cord Failure to do so can result in property damage personal injury and or death 7 Plug into a grounded 3 prong outlet 8 Press RESET on the power supply cord Air Conditioner Use Operating your air conditioner properly helps you to obtain the best possible results This section explains proper air conditioner operation IMPORTANT m If you turn off the air conditioner wait at least 3 minutes before turning it back on This prevents the air conditioner from blowing a fuse or tripping a circuit breaker 11 m Do nottry to operate your air conditioner in the cooling mode when outside temperature is below 65 F 18 C The inside evaporator coil will freeze up and the air conditioner will not operate properly NOTE In the event of a power failure your air conditioner will operate at the previous settings when the power is restored o 1 2 Starting Your Air Conditioner Digital Control Fan Only Press POWER to turn on air conditioner POWER NOTE When
11. e wall installation NW Saw E 1 2 5 cm or thicker lumber E Wood preservative E 7 10 x 1 wood screws NW Caulk Parts supplied on some models Check that all parts are included in parts package 4 AO Do A Support brackets with F 10 x 72 pan head Phillips adjustment bolts 2 screws 6 B Foam seals 2 G 10 x 34 round head screws 6 C Window lock bracket 2 H 10 x pan head Phillips D 10 x 14 pan head Phillips screws 4 screws 6 I Top channel E 10 x 78 washer head J Side curtains 2 Phillips screws 4 K 10 x pan head Phillips screws 2 Installation Requirements Location Requirements IMPORTANT Observe all governing codes and ordinances Check the location where air conditioner will be installed Proper installation is your responsibility Make sure you have everything necessary for correct installation The location should provide NW Grounded electrical outlet within 4 ft 122 cm of where the power cord exits the air conditioner NOTE Do not use an extensioncord E Free movement of air in room to be cooled E A large enough opening for the air conditioner NW Adequate wall support for weight of air conditioner Air con ditioner weighs between 145 and 200 Ibs 66 to 91kg NOTE Cabinet louvers must not be obstructed Air must be able to pass freely through the cabinet louvers A A Cabinet louvers Window installation Electrical Requirements Window openi
12. ill follow the safety alert symbol with the word WARNING or CAUTION These words mean Indicates a hazard which if not AWARNING avoided can result in severe personal injury or death and damage to product or other property ACAUTION Indicates a hazard which if not avoided can result in personal injury and damage to product or other property All safety messages will tell you what the potential hazard is tell you how to reduce the chance of injury and tell you what will happen if the instructions are not followed NOTICE Indicates property damage can occur if instructions are not followed IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of fire electrical shock or injury when using your air conditioner follow these basic precautions E Plug into a grounded 3 prong outlet E Do not remove plug ground prong E Do not use a plug adapter E Do not use an extension cord NW Unplug air conditioner before servicing mM Use two or more people to move and install air conditioner SAVE THESE INSTRUCTIONS Tools and Parts Gather the required tools and parts before starting installation Read and follow the instructions provided with any tools listed here Tools Needed MW Flat blade and Phillips screwdrivers MW Level E Tape measure E Drill and s or smaller bit Through the wall installation In addition to the tools listed above the following tools and sup plies are needed for though th
13. ioner cabinet A Top channel B 10 x 78 washer head Phillips thread cutting screws Attach Side Curtains 1 Locate provided bag of screws 2 Insert top and then bottom of right hand curtain housing in top and bottom curtain channels on air conditioner Top view A Curtain housing B Curtain top channel on air conditioner Bottom view l A B A Curtain housing B Curtain bottom channel on air conditioner 3 Extend right hand curtain outward so you may insert the first screw through the middle hole of the curtain Using 10 x Ya pan head Phillips screw screw curtain to middle hole in air conditioner cabinet NOTE This screw is required to correctly attach curtain top to bottom to the air conditioner cabinet gt IS 10 4 While the right hand curtain is still extended insert 10 x 1 4 pan head Phillips screws into the top and bottom slots of curtain Screw curtain to the top and bottom holes in the air conditioner cabinet side 5 Slide the curtain housing into the curtain channels as far as it will go 6 Repeat above steps for the left hand curtain Attach foam adhesive seal Attach foam adhesive seal along the bottom of the curtain bottom channel AN A B A Curtain housing B Foam adhesive seal Install Cabinet into Window Handle air conditioner careful
14. ir conditioner Failure to do so can result in back or other injury Remove packaging materials m Remove and dispose of or recycle packaging materials Remove tape and glue residue from surfaces before turning on the air conditioner Rub a small amound of liquid dish soap over the adhesive with your fingers Wipe with warm water and dry mM Do not use sharp instruments rubbing alcohol flammable fluids or abrasive cleaners to remove tape or glue These products can damage the surface of your air conditioner m Handle air conditioner carefully and gently 1 Remove the air conditioner from the carton and place it on cardboard 7 Remove the ground screw and ground wire from wer the front of the air conditioner Save the ground 2 Remove shipping screws from the rear of the cabinet if present Era il M E Ai i i S Wy l tin Mn IMAN m Im A pn It in ll Mt u May U k HN Hi i N i ul Mm ll 1 SH ANO i gi IN A ln nu in wh MA Nit I Ch Mt Min N Mn MH Os tn nn ln ann N Ha a ES Un IN tn IS mn NIS ma Null fT Anm Na Un N i in Many a Hm Kun Mii A Green ground wire B Ground screw A per DER 8 Pull on handle to slide air conditioner out of a de seen cabinet Place air conditioner on cardboard Remove front grille by pulling bottom of grille upward Remove hinges at top 4 Remove air filter 5 Remove the window lock bracket and screw from
15. l distort and Exterior wall I l Me A Max Wall thickness allowed 8 1 4 provide a poor air seal between cabinet and air conditioner 8 Caulk all outside wall openings around cabinet Complete Installation NOTE Handle air conditioner carefully and gently 2 Insert air conditioner into cabinet 1 Make sure the free end of the ground wire is outside of the cabinet Excessive Weight Hazard Use two or more people to move and install your air conditioner Failure to do so can result in back or other injury A Make sure the free end of the ground wire is outside of the cabinet A WARNING Electrical Shock Hazard Connect green ground wire to ground screw Failure to do so can result in property damage personal injury and or death 3 Connect green ground wire to cabinet base with ground screw Position ground wire pointing straight up Put excess ground wire between coil and air conditioner cabinet HOTA AMM AA DT A i d in Im un AA Itu h LA Al U IN A Mn TH Mn nt Midday May Hm Hm A re Sea Ll IM II M SM a y UM nn ln gt ain m Uy Mn Mm im In Im CPU rpp LO y S Hg y Otin N Hipp U pp Mp Mh e AN Pan pp Pon M up Mn IM Up e a ln 5 A n E E SC A Green ground wire B Ground screw 4 Push front panel straight on and then lower it slightly to lock it into place 5 Using 1 10 x s round head screw and 2 9 5X 3 8 pan head Phillips screws
16. ly and gently Be sure your air conditioner cabinet does not fall out of the opening during installation or removal m The place where the power cord exits the air conditioner should be no more than 4 ft 122 cm from a grounded 3 prong power outlet Do not place cabinet where front louvers will be blocked Do not place cabinet where outside louvers will be blocked 1 Center empty cabinet in window Check that lower rail of air conditioner cabinet is behind and against back side of windowsill Maintain a firm hold on the air conditioner cabinet Lower window sash to hold cabinet in place 2 Measure the distance between the right hand side of the cabinet and the inside of the window channel 3 Repeat for the left side Adjust the cabinet until the distance on each side is the same I A j f f 4 A Window sash B Empty cabinet C Window channel D Window Seal A B holes in the cabinet and into the windowsill 5 Attach cabinet to windowsill with 4 10 x 7 pan head Phillips screws A 10 x 7 8 pan head Phillips screws B Windowsill 6 Check that air conditioner cabinet is tilted to the outside so that water will run to the outside Use a e drill bit to drill 4 starter holes 3s deep through the 4 Attach Side Curtains to Window Frame 1 Pull left hand curtain out until it fits into window channel Use a 2 drill bit to
17. mp cloth 4 Air dry front panel completely Repairing Paint Damage Check once or twice a year for paint damage This is very important especially in areas near oceans or where rust is a problem If needed touch up with a good grade enamel paint Annual Maintenance Your air conditioner needs annual maintenance to help ensure steady top performance throughout the year Call your local authorized dealer to schedule an annual checkup The expense of an annual inspection is your responsibility Troubleshooting Before calling for service try the suggestions below to see whether you can solve your problem without outside help Air conditioner will not operate A WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet Do not remove ground prong Do not use an adapter Do not use an extension cord Failure to do so can result in property damage personal injury and or death The power supply cord is unplugged Plug into a grounded 3 prong outlet See Electrical Requirements The power supply cord has tripped Reset button has popped out Press and release RESET listen for click Reset button will latch and remain in to resume operation A household fuse has blown or a circuit breaker has tripped Replace the fuse or reset the circuit breaker If the problem continues call an electrician See Electrical Requirements Depending on model the Power button has not been pressed or the Fan con
18. mp time delay fuse or circuit breaker m Use on single outlet circuit only CP18 CP24 m 230 volt 207 min 253 max m 0 12 amps A 17 C Wood thickness m 15 amp time delay fuse or circuit breaker B 26 14 D 4 minimum to m Use on single outlet circuit only 8 maximum Recommended grounding method This air conditioner must be grounded This air conditioner is equipped with a power supply cord having a grounded 3 prong plug To minimize possible shock hazard the cord must be plugged into a mating grounded 3 prong outlet grounded in accordance with all local codes and ordinances If a mating outlet is not available it is the customer s responsibility to have a properly grounded 3 prong outlet installed by a qualified electrical component installer It is the customer s responsibility To contact a qualified electrical installer and To assure that the electrical installation is adequate and in conformance with National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances Copies of the standards listed may be obtained from National Fire Protection Association One Batterymarch Park Quincy MA 02269 Power Supply Cord NOTE Your unit s device may differ from the ones shown B A A Reset button B Test button This room air conditioner is equipped with a power supply cord required by UL This power supply cord contains state of the art electronics that sense leakage cu
19. ng measurements m 27 min to 42 max 76 2 cm to 101 6 cm opening width A m 20 min 50 8 cm opening height B A WARN NG Electrical Shock Hazard Turn off electrical power before service or installation All electrical connections and wiring MUST be installed by a qualified electrician and conform to the National Code and all local codes which have jurisdiction Plug into a grounded 3 prong outlet Do not remove power cord ground prong Do not use a plug adapter Do not use an extension cord Failure to do so can result in property damage personal injury and or death A 27 min 76 2 cm B 20 min 50 8 cm Ground wire must be connected to ground screw located in lower right corner of air conditioner when air conditioner is in cabinet The electrical ratings for your air conditioner are listed on the model and serial number nameplate label The model and serial Through the wall installation The wall opening measurements should be number label is located behind the front panel on the flange below the control panel area NW Height A 17 plus twice thickness of wood used to build 2 ame Specific electrical requirements are listed in the chart below Follow the requirements for the type of plug on the power supply m Width B 26 cord Mm Depth D 4 minimum to 8 maximum Power supply cord Wiring requirements CP15 m 115 volt 103 5 min 126 5 max m 0 12 amps m 15 a
20. nter at 1 800 541 6645 or your Friedrich Air Conditioning Co nearest authorized service center You also can visit the Dealer Customer Service Locator at www friedrich com to locate your nearest authorized 10001 Reunion Place Suite 500 Friedrich Service Center San Antonio TX 78216 Or email tac Ofriedrich com Please include a daytime phone number in your correspondence 15 Z FRIEDRICH Friedrich Air Conditioning Company 10001 Reunion Place Suite 500 78216 800 541 6645 www friedrich com ROOM AIR CONDITIONERS LIMITED WARRANTY FIRST YEAR ANY PART If any part supplied by FRIEDRICH fails because of a defect in workmanship or material within twelve months from date of original purchase FRIEDRICH will repair the product at no charge provided room air conditioner is reasonably accessible for service Any additional labor cost for removing inaccessible units and or charges for mileage related to travel by a Service Agency that exceeds 25 miles one way will be the responsibility of the owner This remedy is expressly agreed to be the exclusive remedy within twelve months from the date of the original purchase SECOND THROUGH FIFTH YEAR SEALED REFRIGERANT SYSTEM If the Sealed Refrigeration System defined for this purpose as the compressor condenser coil evaporator coil reversing valve check valve capillary filter drier and all interconnecting tubing supplied by FRIEDRICH in your Room Air Conditioner fails because of a defect
21. of the cbine should extend 19 1 mm into the room If there is trim the cabinet should extend 19 1 mm past the trim A Outside width B Outside height C Depth 4 Apply wood preservative to the outside exposed surface 5 Insert the frame in the wall opening Square and level frame 6 Attach frame securely to the wall A 34 19 1 mm extending into room B Trim Install Cabinet into Wood Frame 1 Remove top channel and both side channels using a 1 4 nut driver or socket wrench Discard top channel and both side 4 Use a level to check that cabinet is level side to side channels 2 Cut two pieces of standard 1 lumber supplied by installer to the length and width required Place in front and back of bottom sill channel Secure with nails supplied by installer be outside of exterior wall surface Front edge of louvers must always 34 Minimum A Level Cabinet front y i 1 Thick lumber NN 1 Minimum gt 5 Check that air conditioner cabinet is tilted to the outside so that water will run to the outside 6 Reuse the insulation to seal opening between cabinet and y frame 74 Slope down t Position and secure cabinet 7 Use existing holes in sides and top of cabinet and 7 10 x 1 Inside wall downward Slope outside for wood screws not provided to attach cabinet to frame gt drainage l ae NOTE Do not overtighten screws or cabinet wil
22. r conditioner cabinet does not fall out of the opening during installation or removal m The place where the power cord exits the air conditioner should be no more than 4 ft 122 cm from a grounded 3 prong outlet m It is the customer s responsibility and obligation to have this product installed by a qualified technician familiar with through the wall room air conditioner installations Do not block the louvers on the front panel Do not block the louvers on the outside of the air conditioner Option 1 Wood metal or plastic molding When using a wood metal or plastic molding the wood frame should line up with inside wall as shown ABC A Trim Molding C Wood wall framing B Inside wall D Louvers surface Option 2 Plastered wall with no molding If the plastered wall is to be flush with the cabinet and no molding is used the wood frame must be set 1 2 13 mm into the inside wall A Plastered wall C Wood frame B Inside wall D Louvers Install Wood Frame 1 Construct wood frame See Location Requirements for dimensions 2 Measure outside width and height of frame to determine wall Opening dimensions 3 Cut opening through the wall Remove and save insulation NOTES m Dimension for depth depends on wall thickness and type of molding m Do not block louvers in air conditioner cabinet m Use 2 x 4 or thicker lumber for wood frame 3 Insert cabinet into the framed wall opening the top
23. rea They are listed in the Yellow Pages If assistance is required in obtaining warranty performance write to Room Air Conditioner Service Manager Friedrich Air Conditioning Co P O Box 1540 San Antonio TX 78295 1540 LIMITATIONS THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES Anything in the warranty notwithstanding ANY IMPLIED WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE AND OR MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS EXPRESS WARRANTY MANUFACTURER EXPRESSLY DISCLAIMS AND EXCLUDES ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGE FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY Performance of Friedrich s Warranty obligation is limited to one of the following methods 1 Repair of the unit 2 A refund to the customer for the prorated value of the unit based upon the remaining warranty period of the unit 3 Providing a replacement unit of equal value The method of fulfillment of the warranty obligation is at the sole discretion of Friedrich Air Conditioning NOTE Some states do not allow limitations on how long an implied warranty lasts or do not allow the limitation or exclusion of consequential or incidental damages so the foregoing exclusions and limitations may not apply to you OTHER This warranty gives you specific legal rights and you may also have other rights which vary from state to state PROOF OF PURCHASE Owner must provide proof of purchase in order to receive any warranty related services
24. rom 1 to 24 hours 3 Press TIMER or wait 10 seconds Indicator light will remain on To set the Timer delay for a 1 to 24 hour delay until the air conditioner turns on keeping previous settings 1 Turn off air conditioner 2 Press TIMER Indicator light will flash 3 Press the plus or minus button to change the delay time from 1 to 24 hours 4 Press TIMER or wait 10 seconds Indicator light will remain on To set the Timer delay for a 1 to 24 hour delay until the air conditioner turns on changing previous settings Turn on air conditioner Adjust MODE to desired setting Adjust FAN SPEED to Low Medium or High Adjust temperature between 60 F 15 5 C and 90 F 32 2 C Turn off air conditioner Press TIMER Indicator light will flash Press the plus or minus button to change delay time from 1 to 24 hours 8 Press TIMER or wait 10 seconds Oy Oe m To clear Timer delay program NOTE Air conditioner can be either on or off Press TIMER Indicator light will turn off To operate air conditioner with remote control NOTE Remote control may vary in appearance j rRicprich NOTE Two AAA batteries included power the remote control Replace batteries after 6 months of use or when the remote control starts to lose power To turn the air conditioner on or off Press POWER Power To select the mode Press COOL FAN or SAVER To select the fan speed Press FAN SPEED for Low Medium or
25. rrent If the cord is crushed the electronics detect leakage current and power will be disconnected in a fraction of a second A WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet Do not remove power cord ground prong Do not use a plug adapter Do not use an extension cord Failure to do so can result in property damage personal injury and or death To test your power supply cord 1 Plug power supply cord into a grounded 3 prong outlet 2 Press RESET 3 Press TEST listen for click Reset button will trip and pop out 4 Press and release RESET listen for click Reset button will latch and remain in The power supply cord is ready for operation NOTES The Reset button must be pushed in for proper operation The power supply cord must be replaced if it fails to trip when the test button is pressed or if it fails to reset Do not use the power supply cord as an off on switch The power supply cord is designed as a protective device A damaged power supply cord must be replaced with a new power supply cord obtained from the product manufacturer and must not be repaired The power supply cord contains no user serviceable parts Opening the tamper resistant case voids all warranty and performance claims Installation Instructions Unpacking 6 Remove front panel screw from right side of filter Ah CAUTION a Excessive Weight Hazard Use two or more people to move and install your a
26. s blinds furniture etc The outside temperature is below 65 F 18 C Do not try to operate your air conditioner in the cooling mode when the outside temperature is below 65 F 18 C The temperature of the room you are trying to cool is extremely hot Allow extra time for the air conditioner to cool off a very hot room Windows or doors to the outside are open Close all windows and doors The Vent control is set to OPEN on some models Push the Vent control to CLOSED for maximum cooling and or heating The temperature set point or Thermostat control is not at a cool enough setting Adjust the temperature set point to a cooler setting by pressing the minus button to reduce the temperature or adjust the Thermostat control to a cooler setting by turning the knob clockwise Turn the Fan control to Turbo Cool The air contitioner in the heating mode has insufficient BTU hr for the heating requirements of the room Do not use the air conditioner as a primary source of heat producing appliances during the hottest part of the day A Temperature on display does not match room higher capacity air conditioner may be required depending temperature on the size of the room being cooled m When the compressor and fan motor turn off during Air conditioner cycles on and off too much or does not cool heat room in cooling heating mode m The Mode or Fan control is set to Power Saver on some models Use Power Saver only when you are
27. the air conditioner and set aside pl ye S a D Be AN Xy T o N Mas itp M ma ms IM i tg Ni im u SI 5 tn Mii ai aul arth SH nm ml nin Im gt au l iin M Mm Mm Ua S Nini Mn Min NU In BS hip ih KTTT N Ci N th AN os Ph ng han 3 A Pull Handle th sit WAR In min my olha if 3 Su a NOTE Do not lift push pull or remove any expanded polystyrene foam from inside the air conditioner It is not packing material Window Installation on some models NOTES m Handle air conditioner carefully and gently m Be sure your air conditioner cabinet does not fall out of the opening during installation or removal m The place where the power cord exits the air conditioner should be no more than 4 ft 122 cm from a grounded 3 prong power outlet Do not block the louvers on the front panel Do not block the louvers on the outside of the air conditioner Attach Top Channel NOTE Attach top channel and side curtains to air conditioner cabinet before placing cabinet in window 1 Locate provided bag of screws 2 Place top channel on top of air conditioner cabinet lining up the 4 holes in top channel with the 4 holes on top of air conditioner cabinet 3 Using 4 10 x washer head Phillips thread cutting screws attach top channel to air condit
28. tisfaction in the performance of your unit For years of trouble free service please follow the installation instructions closely We cannot overemphasize the importance of proper installation We have added new information to the basic instructions to help you achieve success A WARNING Refrigeration system under high pressure Do not puncture heat expose to flame or incinerate Only certified refrigeration technicians should service this equipment R410A systems operate at higher pressures than R22 equipment Appropriate safe service and handling practices must be used Only use gauge sets designed for use with R410A Do not use standard R22 gauge sets AA WARNING Please read this manual thoroughly prior to equipment installation or operation It is the installer s responsibility to properly apply and install the equipment Installation must be in conformance with the NFPA 70 2008 National Electric Code or current edition International Mechanic Code 2009 or current edition and any other applicable local or national codes Failure to do so can result in property damage personal injury and or death Your safety and the safety of others are very important We have provided many important safety messages in this manual and on your appliance Always read and obey all safety messages This is a safety Alert symbol This symbol alerts you to potential hazards that can kill or hurt you and others All safety messages w
29. trol is turned to Off Press POWER or turn the Fan control to an active setting The local power has failed Wait for power to be restored Air conditioner blows fuses or trips circuit breakers Too many appliances are being used on the same circuit Unplug or relocate appliances that share the same circuit Time delay fuse or circuit breaker of the wrong capacity is being used Replace with a time delay fuse or circuit breaker of the correct capacity See Electrical Requirements An extension cord is being used Do not use an extension cord with this or any other appliance You are trying to restart the air conditioner too soon after turning the unit off Wait at least 3 minutes after turning the unit off before trying to restart the air conditioner Normal Sounds When your air conditioner is operating normally you may hear sounds such as Droplets of water hitting the condenser causing a pinging or clicking sound The water droplets help cool the condenser Air movement from the fan Clicks from the thermostat cycle Vibrations or noise due to poor wall or window construction A high pitched hum or pulsating noise caused by the modern high efficiency compressor cycling on and off Air conditioner power supply cord trips Reset button pops out m Disturbances in your electrical current can trip Reset button will pop out the power supply cord Press and release RESET listen for click Reset button will latch and
Download Pdf Manuals
Related Search