Franke Consumer Products FDB 9078 SIL
Contents
1. Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version connect the hood to the chimney using either a flexible or rigid pipe 150 or 120 mm the choice of which is left to the installer To install a 120 mm air exhaust connection insert the re ducer flange 9 on the hood body outlet Fix the pipe in position using sufficient pipe clamps not sup plied Remove any activated charcoal filters AIR OUTLET RECIRCULATION VERSION e Connect the Flange 0150 10 to the bottom end of the Connec tor 15 Join the Hood canopy outlet to the Flange on the bottom part of the Connector using a rigid or flexible pipe 9150 mm selec tion of which is at the discretion of the installation technician Make sure that the Activated charcoal odour filter has been fitted ELECTRICAL CONNECTION Connect the hood to the mains through a two pole switch hav ing a contact gap of at least 3 mm Remove the grease filters see paragraph Maintenance being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan Fitting the Chimney Upper chimney Open the two side pieces out slightly hook them up behind the brackets 7 2 1 and bring them back together again until they are in contact N B The bottom bracket may be omitted Fix the sides of the Brackets using 4 Screws 12c 2 9 x 9 5 provided Make sure that the Connector outlet is in cor2. 1 as indicated X mm under the first bracket X height of the Upper chimney provided aligning its centre grooves with the vertical reference line Mark the centres of the holes in the bracket As shown in the drawing mark a reference point 116 mm from the vertical reference line and 565 mm above the horizontal reference line As shown in the drawing mark a reference point 280 mm from the vertical reference line and 67 mm above the horizontal reference line Repeat this operation on the other side N B Should installation of the lower bracket 7 2 1 interfere in any way with that of the hood canopy the lower bracket 7 2 1 may be omitted Drill the points marked using a 9 8 mm drill bit Insert the plugs 11 into the holes Fix the lower bracket 7 2 1 if it is to be fitted using the screws 12a 4 2 x 44 4 provided Fix the upper bracket 7 2 1 and the bracket supporting connection 15 together using the 2 screws 12a 4 2 x 44 4 provided Tighten the 2 screws 12a 4 2 x 44 4 provided in the hood canopy fixing bores leaving a gap of 5 6 mm between the wall and the heads of the screws Hood body installation Before hooking the hood body it is necessary to tighten 2 Vr screws placed in the fixing points of the body Hook the hood body on the 12a screws Tighten completely 12a support screws The correct hood body position can be levelled with Vr screws Fix the hood definitively by tightening the 12a security screws
3. it Unhook the security chain by opening the spring catch Disconnect the panel from the hood canopy by sliding the fix ing pin lever The comfort panel must never be washed in a dishwasher Clean the outside by using a damp cloth and neutral liquid de tergent Clean the inside as well by using a damp cloth and neutral de tergent do not use wet cloths or sponges or jets of water do not use abrasive substances When the above operation has been completed hook the panel back and the spring catch to the hood canopy and close it by turning the knob in the opposite direction Metal grease filters The Filters can be washed in the dishwashing They need to be washed when FF sign appears on the display or in any case every 2 months or even more frequently in case of particularly inten sive use of the hood Alarm reset Switch off the hood and the lights If the 24h function has been activated this has to be deactivated Press the E key till the display is unlit Cleaning the filters Pull the comfort panels to open them Remove the filters one by one pushing them towards the back side of the hood unit and simultaneously pulling downwards Any kind of bending of the filters has to be avoided when washing them Before fitting them again into the hood make sure that they are completely dry The colour of the filter sur face may change throughout the time but this has no influence to the filter efficiency
4. FRANKE A B g Instructions for use and installation Cooker Hood Istruzioni per l uso e l installazione Cappa Mode d emploi et installation Hotte de Cuisine Bedienungsanleitung und Einrichtung Dunstabzugshaube Kullanim ve montaj talimatlari Davlumbaz Uzivatelsk Po ru ka Odsava par FDB 9078 SIL K INDEX RECOMMENDATIONS AND SUGGESTIONS 3 INDICE CONSIGLELE SUGGERIMENT 4 2 ecnccttetttet eret retener deerant na dh vc n ce 14 CARATTERISTICHE INSTALLAZIONE USO ria MANUTENZIONE iet una e MI AR ARRENE SOMMAIRE CONSEILS ET SUGGESTIONS ates tranne a ERRORI ae ea ete tas aa TAI i e 25 CARACTERISTIQUES 26 INSTALLATION 28 UTILISATION ere 31 ENTRETIEN AIR 32 INHALTSVERZEICHNIS EMPEEHEUNGEN UND HINWEISE rcr etre tret E ett tne tte tates 36 CHARAKTERISTIKEN ich ritenere teuren item died tinet 37 MONTAGE creel M 39 s cem 42 WARTUNG tct ta ee treten ede adt De Eee aee ADHERE B VA ident ec deen DA i 43 IGERIKLER TAVSIYELER VE ONERILER rie 47 OZELLIKLER MONT KULLANIM BAKIM OBSAH RADY ADOPORUGCENT ciali alii 58 HCAVNIPARAMETRY ori O 59 INSTAEACE sry rote anali conan e E N n 61 Ud eer rem oi AEE a 64 RER 65 RECOMMENDATIONS AND SUGGESTIONS A The Instructions for Use apply to several versions o
5. OFING ELEMENT Open the Comfort panels by pulling them Remove the Metal grease filters Remove the Activated charcoal filter using the hooks pro vided Pull out the Soundproofing Element from below pressing the side fins to disconnect it from the slot in the Hood Canopy Clean it with a damp cloth and replace it first making sure that it is completely dry Replace the Activated charcoal filters Replace the Metal grease filters Close the Comfort panels Lighting unit REPLACING OF THE LED UNIT LED To remove the lighting unit a screwdriver can be used in order to slightly press the side part of the unit Remove the unit remove the electrical connector and replace the unit with a new one To purchase contact technical support Warning This appliance is fitted with a white LED lamp classed as 1M according to EN 60825 1 1994 A1 2002 A2 2001 standards maxi mum optical power emitted 439nm 7uW Do not look directly at the light through optical devices binoculars magnifying glasses FRANKE Franke S p a Via Pignolini 2 37019 Peschiera del Garda VR www franke it 436004404 ver7 CE
6. When fitting the filters into the hood pay attention that they are mounted in correct position the handle facing outwards Close the comfort panel Charcoal filter recycling version e This filter cannot be washed or regenerated It must be replaced when the EF appears on the display or at least once every 4 months Activation of the alarm signal In the recycling version hoods the filter saturation alarm must be activated during instal lation or later Switch off the hood and the lights Disconnect the hood from the mains supply When restoring the connection press and hold B key When releasing the key two rotating rectangles appear on the display Within 3 seconds press the B key until a flashing confirmation appears on the dispaly 2 flashes with EF charcoal filter saturation alarm ACTIVATED I flash with EF charcoal filter saturation alarm DEACTIVATED REPLACING THE CHARCOAL FILTER Reset of the alarm signal Switch off the hood and the lighting If the 24h function has been activated this has to be deactivated Press the E key until the display is unlit Replacing of the filter Open the comfort panels by pulling them downwards e Remove the metal grease filters e Remove the saturated charcoal filter by releasing the fixing hooks Fit the new filter and fasten it in its correct position Put the metal grease filters in their seats Close the comfort panels CHANGING THE SOUNDPRO
7. f this appliance Accord ingly you may find descriptions of individual features that do not apply to your specific appliance INSTALLATION The manufacturer will not be held liable for any damages resulting from in correct or improper installation The minimum safety distance between the cooker top and the extractor hood is 650 mm some models can be installed at a lower height please re fer to the paragraphs on working dimensions and installation Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood For Class appliances check that the domestic power supply guarantees adequate earthing Connect the extractor to the exhaust flue through a pipe of minimum diame ter 120 mm The route of the flue must be as short as possible Do not connect the extractor hood to exhaust ducts carrying combustion fumes boilers fireplaces etc If the extractor is used in conjunction with non electrical appliances e g gas burning appliances a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas The kitchen must have an opening communicating directly with the open air in order to guarantee the entry of clean air USE The extractor hood has been designed exclusively for domestic use to elimi nate kitchen smells Never use the hood for purposes other than for which it has been designed Never leave high naked fla
8. mes under the hood when it is in operation Adjust the flame intensity to direct it onto the bottom of the pan only making sure that it does not engulf the sides Deep fat fryers must be continuously monitored during use overheated oil can burst into flames Do flamb under the range hood risk of fire This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concern ing use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appli ance MAINTENANCE Switch off or unplug the appliance from the mains supply before carrying out any maintenance work Clean and or replace the Filters after the specified time period Fire hazard Clean the hood using a damp cloth and a neutral liquid detergent The symbol on the product or on its packaging indicates that this product may be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed informatio
9. n about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product CHARACTERISTICS Dimensions 310 350 max 192 max 1192 min 617 min 740 Dimensions of the hood in ducting version Dimensions of the hood in recycling version Components Ref Product Components 1 1 Hood Body complete with Controls Light Blower Filters 2 1 Telescopic Chimney comprising 24 1 Upper Section 2 2 1 Lower Section 9 1 Reducer Flange 150 120 mm 10 1 Flange 150 mm 15 1 Air Outlet Connection 30 1 Comfort Panels Ref Installation Components 7 231 2 Upper Chimney Section Fixing Brackets 11 8 Wall Plugs 12a 8 Screws 4 2 x 44 4 12 6 Screws 2 9 x 9 5 Q ty Documentation Instruction Manual INSTALLATION Drilling the Wall and Fixing the Brackets 650 mm min 9 Draw the following on the Wall a Vertical line up to the ceiling or top surface at the centre of the area in which the Hood is to be fitted a Horizontal line 650 mm min above the Cooker Top Rest the Bracket 7 2 1 as indicated 1 2 mm from the ceiling or surface above the hood aligning its cen tre grooves with the vertical reference line Mark the centres of the holes in the bracket Rest the Bracket 7 2
10. r saturation is going on it is pos Si ia 5 i 5 p FF Indicates that the metal grease filters sible to reset the alarm by pressing this key for saturation alarm has been triggered and about 3 seconds The indication is visible only the filters need to be washed The alarm when the motor is off is triggered after 100 working hours EF Indicates that the charcoal filter satura tion alarm has been triggered and the fil ter has to be replaced the metal grease filters must also be washed The charcoal filter is triggered after 200 working hours F By pressing this key it is possible to set the Indicates alternately the selected speed of the delayed shutdown of the appliance to 30 min hood and the time left before the hood shut utes This function is suitable for a complete down The spot down on the right side flashes elimination of the residual smells It can be activated at any position and it is deactivated by pressing the key again or by switching off the motor G Turns the light on and off Turns the light on and off at reduced intensity MAINTENANCE REMOTE CONTROL OPTIONAL The appliance can be controlled using a remote control powered by a 1 5 V carbon zinc alkaline batteries of the standard LR03 AAA type not included Do not place the remote control near to heat sources Used batteries must be disposed of in the proper manner Cleaning the Comfort Panels Pull the Comfort Panel to open
11. respondence with the Chimney openings Lower chimney Open out the two Chimney side flaps hook them up between the upper chimney and the wall and then close them up again until they touch Fix the lower part to the Hood canopy at the sides using 2 screws 12c 2 9 x 9 5 provided Fit the Comfort Panel on the body using the fixing pins provided and hook up the safety catch Control board Key Function Display A Switches the extractor motor on and off at the Indicates the selected speed latest selected speed B Decreases the suction speed Increases suction speed D By pressing this key it is possible to activate HI appears The spot down on the right side the intensive speed from any previously se flashes once a second lected speed The intensive speed can be acti vated even when the motor is OFF This speed has been timed at 10 minutes After that time the system activates automatically the latest selected speed This function is suitable for cooking conditions when vapours and smells are of the utmost emission E By pressing this key it is possible to set up the Indicates the 24 function The spot down on motor to a suction speed at 100 m h lasting 10 the right side flashes and the motor is on minutes every hour After this the motor i Pee Once the process is finished the previous indi switches off automatically When the filte
Download Pdf Manuals
Related Search