Home

Ford 2000 Ranger Automobile User Manual

1. To stow the seat fold seat back down and raise seat assembly to the fully upright position Do not install a child seat in a center facing jump seat SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips To reduce the risk of injury make sure children sit where they can be properly restrained Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision All occupants of the vehicle including the driver should always properly wear their safety belts even when an air bag SRS is provided It is extremely dangerous to ride in a cargo area inside or outside of a vehicle In a collision people riding in these areas are more likely to be seriously injured or killed Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts Be sure everyone in your vehicle is in a seat and using a safety belt properly 72 Seating and safety restraints In a rollover crash an unbelted person is significantly more likely to die than a person wearing a seat belt Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair 1 Use the shoulder belt on the outside shoulder only Never wear the shoulder
2. 3 Attach the new wiper to the wiper arm and press it into place until a click is heard INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width For example e Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set Tire Quality Grades apply to new pneumatic tires for use on passenger cars They do not apply to deep tread winter type snow tires space saver or temporary use spare tires tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575 104 c 2 U S Department of Transportation Tire quality grades The U S Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it 181 Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course For example a tire graded 150 would wear one and one half 1 1 2 times as well on the government course as a tire graded 100 The relative performance of tires depends upon the actual cond
3. operates in gears one through four Overdrive can be deactivated by pressing the transmission control 0 D 4 switch on the gearshift lever ON OFF 4 The transmission control indicator light TCIL will illuminate on the 0 D instrument cluster O F F Drive Not shown on the display Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the position The O D OFF indicator will illuminate on the instrument cluster Transmission operates in gears one through three Drive provides more engine braking than Overdrive and is useful when e driving with a heavy load e towing a trailer up or down steep hills e additional engine braking is desired If towing a trailer refer to Driving while you tow in the Trailer Towing chapter To return to Overdrive mode press the transmission control switch The O D OFF indicator will no longer be illuminated Each time the vehicle is started the transmission will automatically return to normal overdrive mode Every time the vehicle is shut off and restarted you must press the transmission control switch to cancel overdrive operation if driving in overdrive is not desired 2 Second Use 2 Second to start up on slippery roads or to provide N D poaa ee ee on fee ee downgrades Transmission operates only in Second gear 113 Driving 1 First Use 1 Low to provide maximum engine bra
4. 209 214 215 Special notice wo ceeeeeeeeeeeeee 3 ambulance conversions 3 utility type vehicles 00 3 Specification chart lubricants srein 212 214 Speed control cceeceeeceeeeees 55 Speedometer cccccccesseeeeenes 16 Starting your vehicle 100 102 JUMP starting caceicscscccscescasess 152 Steering wheel IGNE gainian ai 60 Tachometer prsna 15 Tires esiseninensess 147 181 182 183 Changing 3 sascestasieavedsoxtvecs 147 150 checking the pressure 183 TEPIACING sessir setrini 184 TOLAUING scsccsovssssesissccdersssenadeasnees 183 snow tires and chains 185 IPE BTACES sacseccsazeessanceesacheassess 182 treadwear cceeeeesecceeesteeeeeeees 182 TOWING cdestecdsesdesveloesitsiancscakicasess 183 recreational towing 4 136 WLECKED os sccssesadssasscatesisccesieceeeees 157 Traction lok rear axle 124 Transfer case fluid checking csscesscdcchecscanoe s 177 Transmission automatic operation 111 fluid checking and adding automatic 2 173 fluid checking and adding MANUAL 6 05 svesstdecatesiocesasseeets 176 Index fluid refill capacities 209 lubricant specifications 212 214 manual operation 0008 116 Trip Odometer cccccsessseeeeees 16 T rn SIGNAL socceiseeveriscseeteesvorssy 11 54 Vehicle dimensions 66 215 Vehicle Identification Number VIN
5. 4 Insert the belt tongue into the proper buckle the buckle closest to the direction the tongue is coming from for that seating position until you hear and feel the latch engage Make sure the tongue is latched securely by pulling on it 5 To put the retractor in the automatic locking mode grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard e 6 Allow the belt to retract The belt will click as it retracts to indicate it is in the automatic locking mode 97 Seating and safety restraints 7 Pull the lap belt portion across the child seat toward the buckle and R pull up on the shoulder belt while pushing down with knee on the child seat 8 Allow the safety belt to retract to Kw remove any slack in the belt x gt 9 Before placing the child in the seat forcibly tilt the seat forward and back to make sure the seat is securely held in place A 10 Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode you should not be able to pull more belt out If the retractor is not locked unbuckle the belt and repeat steps two through nine Check to make sure the child seat is properly secured before each use 98 Seating and safety restraints Attaching safety seats with tether straps Some manufacturers make safety seats that include a tether strap that goes over the back of the vehicle seat
6. Do not put washer fluid in the engine coolant reservoir Washer fluid placed in the cooling system may harm engine and cooling system components ENGINE COOLANT E Checking engine coolant Your engine s cooling system has been factory filled with a 50 50 mixture of distilled water and Ford Premium Engine Coolant E2FZ 19549 AA in Canada Motorcraft CXC 10 or an equivalent premium engine coolant that meets Ford specification ESE M97B44 A 168 Maintenance and care A 50 50 mixture of distilled water and Ford Premium Engine Coolant provides e maximum cooling system efficiency e freeze protection down to 36 C 34 F e boiling protection up to 129 C 265 F e protection against rust and other forms of corrosion e an accurate temperature readout from the engine coolant gauge The engine coolant must be maintained at the correct fluid level and concentration to work properly If the engine coolant fluid level and concentration is not maintained correctly damage to the engine and cooling system may result When the engine is cold check the level of the engine coolant in the reservoir e The engine coolant should be at the cold fill level or within the cold fill range as listed on the engine coolant reservoir depending upon application Refer to the Scheduled Maintenance Guide for service interval schedules e Be sure to read and understand Precautions when servicing your vehicle in
7. Never place a rear facing infant seat in the front seat unless the passenger air bag is turned off Steps you can take to properly position yourself away from the airbag e Move your seat to the rear as far as you can while still reaching the pedals comfortably e Recline the seat slightly one or two degrees from the upright position Do not put anything on or over the air bag module Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury Do not attempt to service repair or modify the Air Bag Supplemental Restraint System or its fuses See your Ford or Lincoln Mercury dealer Children and air bags For additional important safety information read all information on safety restraints in this guide Children must always be properly restrained Failure to follow these instructions may increase the risk of injury in a collision An infant in a rear facing seat faces a high risk of serious or fatal injuries from a deploying passenger air bag Rear facing infant seats should NEVER be placed in the front seats unless the passenger air bag is turned off See Passenger air bag ON OFF switch 85 Seating and safety restraints How does the air bag supplemental restraint system work The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration The fact that the air bags did not
8. 191 Maintenance and care Fuel Filter For fuel filter replacement see your dealer or a qualified service technician Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the fuel filter Replace the fuel filter with an authorized Motorcraft part The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you the driver You must gather information as accurately and consistently as possible Fuel expense frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy We do not recommend taking fuel economy measurements during the first 1 600 km 1 000 miles of driving engine break in period You will get a more accurate measurement after 3 000 km 5 000 km 2 000 miles 3 000 miles Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill Capacities section of the Capacities and specifications chapter The advertised capacity is the amount of the indicated capacity and the empty reserve combined Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty Empty reserve is the small amount of usable fuel remaining in the fuel tank afte
9. 4X4 HIGH 4WD High Power delivered to front and rear axles for increased traction 4X4 LOW 4WD Low Power to front and rear axles at low speeds 119 Driving Shifting from 2WD 2WD high to 4X4 HIGH 4WD high Move the 4WD control to the 4X4 HIGH position e At temperatures below 0 C 32 F shifts from 2WD to 4X4 HIGH should not be performed above 72 km h 45 mph Do not shift into 4X4 HIGH with the rear wheels slipping Shifting from 4X4 HIGH 4WD high to 2WD 2WD high Move the 4WD control to 2WD position at any forward speed e You do not need to operate the vehicle in R Reverse to disengage your front hubs Shifting from 2WD 2WD high to 4X4 LOW 4WD low 1 Bring the vehicle to a stop 2 Depress the brake 3 Place the gearshift in N Neutral automatic transmission or depress the clutch manual transmission 4 Move the 4WD control to the 4X4 LOW position 120 Driving Shifting from 4X4 LOW 4WD low to 2WD 2WD high 1 Bring the vehicle to a stop 2 Depress the brake 3 Place the gearshift in N Neutral automatic transmission or depress the clutch manual transmission 4 Move the 4WD control to the a 2WD position a Shifting between 4X4 HIGH 4WD high and 4X4 LOW 4WD low 1 Bring the vehicle to a stop 2 Depress the brake 3 Place the gearshift in N Neutral automatic transmission or depress the clutch manual transmission 4 Move the
10. J For important information regarding safe operation of this type of vehicle see Preparing to drive your vehicle in this chapter When Four wheel drive 4WD is engaged power is supplied to all four wheels through a transfer case 4WD power can be selected when additional driving power is desired If equipped with the Electronic Shift 4WD System and the instrument panel control is moved to 4WD Low while the vehicle is moving the system will not engage and no damage will occur to the 4WD system Before 4WD Low can be engaged the vehicle must be brought to a complete stop with the brake pedal depressed and the transmission placed in neutral or the clutch pedal depressed on manual transmissions 4WD operation is not recommended on dry pavement Doing so could result in difficult disengagement of the transfer case increased tire wear and decreased fuel economy 4WD system indicator lights The 4WD system indicator lights illuminate only under the following conditions If these lights illuminate when driving in 2WD contact your Ford dealer as soon as possible e 4WD HIGH momentarily 4 D illuminates when the vehicle is started Illuminates when 4H HIGH 4WD High is engaged e 4WD LOW momentarily illuminates when the vehicle is AWD started Illuminates when 4L LOW 4WD Low is engaged Using the electronic shift 4WD system if equipped Positions of the electronic shift system 2WD 2WD High Power to rear axle only
11. 1 Clean the filler plug 2 Remove the filler plug and inspect the fluid level 3 Fluid level should be at bottom of the opening 4 Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening am 5 Install and tighten the fill plug securely Use only fluid that meets Ford specifications Refer to the Capacities and specifications chapter 176 Maintenance and care Checking and adding transfer case fluid if equipped 1 Clean the filler plug 2 Remove the filler plug and inspect the fluid level 3 Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening Use only fluid that meets Ford specifications Refer to the Capacities and specifications chapter DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication Refer to the Scheduled Maintenance Guide for maintenance intervals If the original universal joints are replaced with universal joints equipped with grease fittings lubrication will also be necessary 177 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance free battery which normally does not require additional water during its life of service However for severe usage or in high temperature climates check the battery elect
12. and with a continuous motion pull out enough webbing to buckle the tongue into the correct buckle If you did not pull out enough webbing to reach the buckle allow the tongue to retract fully before trying to pull it out again 78 Seating and safety restraints The lap belts should fit snugly and as low as possible around the hips not around the waist If you need to lengthen the belt unfasten it and repeat the procedure above To unfasten the belt push in the release button prior to opening the rear door Safety belt extension assembly If the safety belt assembly is too short even when fully extended 20 cm 8 inches can be added to the safety belt assembly by adding a safety belt extension assembly part number 611C22 Safety belt extension assemblies can be obtained from your dealer at no cost Use only extensions manufactured by the same supplier as the safety belt Manufacturer identification is located at the end of the webbing on the label Also use the safety belt extension only if the safety belt is too short for you when fully extended Do not use extensions to change the fit of the shoulder belt across the torso Safety belt warning light and indicator chime A The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts Conditions of operation The driver s safety belt is not The safety belt warning light buckled before the ign
13. designed to work with the air bag If you are not a person who meets the requirements stated in the NHTSA Transport Canada deactivation criteria turning OFF the air bag can increase the risk of serious injury or death in a collision Always use safety belts and child restraints properly If a child in a rear facing infant seat must be transported in front the passenger air bag must be turned OFF This is because the back of the infant seat is too close to the inflating air bag and the risk of a fatal injury to the infant when the air bag inflates is substantial The vast majority of drivers and passengers are much safer with an air bag than without To do their job and reduce the risk of life threatening injuries air bags must open with great force and this force can pose a potentially deadly risk in some situations particularly when a front seat occupant is not properly buckled up The most effective way to reduce the risk of unnecessary air bag injuries without reducing the overall safety of the vehicle is to make sure all occupants are properly restrained in the vehicle especially in the front seat This provides the protection of safety belts and permits the air bags to provide the additional protection they were designed to provide If you choose to deactivate your air bag you are losing the very significant risk reducing benefits of the air bag and you are also reducing the effectiveness of the safety belts because safety belts in mode
14. feature When fueling your vehicle 1 Turn the engine off 2 Carefully turn the filler cap counterclockwise 1 8 of a turn until it stops 188 Maintenance and care 3 Pull to remove the cap from the fuel filler pipe 4 To install the cap align the tabs on the cap with the notches on the filler pipe 5 Turn the filler cap clockwise 1 8 of a turn until it stops If the Service Engine Soon Check Engine indicator comes on and stays on when you start the engine the fuel filler cap may not be properly installed Turn off the engine remove the fuel filler cap align the cap properly and reinstall it If you must replace the fuel filler cap replace it with a fuel filler cap that is designed for your vehicle The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used The fuel system may be under pressure If the fuel filler cap is venting vapor or if you hear a hissing sound wait until it stops before completely removing the fuel filler cap Otherwise fuel may spray out and injure you or others If you do not use the proper fuel filler cap excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel system to work improperly in a collision which may result in possible personal injury Choosing the right fuel Use only UNLEADED FUEL The use of leaded fuel is prohibited by law and could damage
15. system s treble output TREB 33 Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the right and left A speakers BAL as Speaker fade adjust Speaker sound can be adjusted between the front and rear A speakers FADE y Tape select e To enter tape mode while in radio mode press the TAPE AMS control Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection To activate the feature momentarily depress the TAPE AMS button Then press either REW for the beginning of the current selection or FF to advance to the next 34 Controls and features selection The tape deck stops and returns to play mode when the AMS circuit senses a blank section on the tape In order to ensure proper operation of the AMS feature the tape MUST have a blank section of at least four seconds duration between programs Rewind The rewind control works in tape mode To rewind in tape mode press the REW control Fast forward The fast forward control works in tape mode e In the tape mode tape direction will automatically reverse when the end of the tape is reached Tape direction select Press SIDE and 1 2 at the same time to play the alternate side of a tape Eject function Press the control to stop and eject a tape E
16. Equipment standard requirements regulating the impulse electrical field strength of radio noise When starting a fuel injected engine avoid pressing the accelerator before or during starting Only use the accelerator when you have difficulty starting the engine For more information on starting the vehicle refer to Starting the engine in this chapter Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system creating the risk of fire or other damage Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire Do not start your vehicle in a closed garage or in other enclosed areas Exhaust fumes can be toxic Always open the garage door before you start the engine See Guarding against exhaust fumes in this chapter for more instructions If you smell exhaust fumes inside your vehicle have your dealer inspect your vehicle immediately Do not drive if you smell exhaust fumes Important safety precautions A computer system controls the engine s idle revolutions per minute RPM When the engine starts the idle RPM runs faster to warm the engine If the engine idle speed does not slow down automatically have the vehicle checked Do not allow the vehicle to idle for more than 10 minutes at high engine RPM Before starting the vehicle 1 Make sure all vehicle occupa
17. FM select control works in radio tape and CD modes gt m m AM FM select in radio mode This control allows you to select AM or FM frequency bands Press the control to switch between AM FM1 or FM2 memory preset stations AM FM select in tape mode Press this control to stop tape play and begin radio play Tune adjust The tune control works in radio mode Tune adjust in radio mode e Press B gt to move to the next frequency up the band whether or not a listenable station is located there Hold for quick movement e Press lt to move to the next frequency down the band whether or not a listenable station is located there Hold the frequencies quickly T control to move through the A 44 Controls and features Seek function The seek function control works in radio tape or CD mode Seek function in radio mode e Press lt q to find the next listenable station down the frequency band e Press gt to find the next listenable station up the al Seek function in tape mode e Press lt q to listen to the previous selection on the tape e Press gt to listen to the next selection on the tape Seek function in CD mode e Press lt q to seek to the previous track of the current disc e Press gt to seek forward to the next track of the current disc After the last track has been 4 4 completed the first track of the replay lt q TUNE gt lt 4 T
18. For high altitude operation reduce GCW by 2 per 300 meters 1 000 ft elevation For definition of terms used in this table see Vehicle Loading earlier in this chapter To determine maximum trailer weight designed for your particular vehicle see Calculating the load earlier in this chapter Maximum trailer weight is shown The combined weight of the completed towing vehicle including hitch passengers and cargo and the loaded trailer must not exceed the Gross Combined Weight Rating GCWR 130 Driving Trailer tow table 4x4 automatic transmission Rear Maximum Maximum Maximum axle GCWR kg trailer frontal area of ratio ibs weight kg Ibs trailer m ft Regular Cab 3 0L 3 73 3401 0 1 751 4 64 7 500 0 3 860 50 3 0L 4 10 3 628 0 1 978 4 64 8 000 0 4 360 50 4 309 0 2 631 4 64 9 500 0 5 800 50 4 309 0 2 631 4 64 9 500 0 5 800 50 SuperCab 3 0L 3 73 13 401 0 1 660 7 500 0 3 660 50 4 0L 3 73 14 309 0 2 549 9 500 5 620 50 4 0L 4 10 4309 0 2 549 4 9 500 0 5 620 50 For high altitude operation reduce GCW by 2 per 300 meters 1 000 ft of elevation For definition of terms used in this table see Vehicle loading earlier in this chapter To determine maximum trailer weight designed for your vehicle see Calculating the load earlier in this chapter Maximum trailer weight is shown The combined weight of the completed towing vehicle including hitch pa
19. J Dolby noise reduction Dolby noise reduction operates only in tape mode Dolby noise gt reduction reduces the amount of hiss and static during tape playback Press the BO control to activate and deactivate Dolby noise reduction Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation Dolby and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation 35 Controls and features Setting the clock Press CLK to toggle between listening frequencies and clock mode while in radio mode To set the hour press and hold the CLK control and press the SEEK control A to decrease hours and to increase hours l 4 lt 4 TUNE gt lt 4 TUNE gt To set the minute press and hold the CLK control and press the TUNE control A to decrease minutes and p to increase minutes lt 4 TUNE gt lt 4 TUNE gt si The CLK control will allow you to switch between media display mode radio station stereo information etc and clock display mode time 36 Controls and features When in clock mode the media information will display for 10 seconds when the radio is turned on and then revert to clock information Anytime that the media is changed new radio station etc the media information will again display for 10 seconds before reverting back to the clock In media mode the media inf
20. Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located The Certification Label is located on the front door latch pillar on the driver s side Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel Please note that in the graphic XXXX is representative of your vehicle identification number Engine number MFD BY FORD MOTOR CO IN U S A DATE XXXXX FGAWR XXXXXX XXXXXXX GVWR XXXXX_ LB XXXXX KG RGAWR XXXXXXX XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE VIN XXXXXXXXXXXXXXXXX TYPE XXXXXXXXXXXXXXX MAXIMUM LOAD OCCUPANTS LUGGAGE XXXKG XXXXLB OCCUPANTS X TOTAL X FR X 2ND X RR OCCUPANTS LUGGAGE XX XXXKG XXXXLB X XXXKG XXXXLB TIRE XXXX XXXXX XXX PRESSURE FR XXX kPa 33 PS COLD PRESSURE RR XXX kPa 33 PSI COLD TRAILER TOWING SEE OWNER GUIDE EXT PNT XXXXXX XXXXXX_ RC XX DSO XXXX_ F0000 BARTINTTR TP PS TR AXLE TR SPR T0000 X XX XXX X XX X XXXX UTC VFOHT 15294A10 GA XXXXXXXXXXXXXXXXX The engine number the last eight numbers of the vehicle identification number is stamped on the engine block transmission frame and transfer case if equipped 217 Customer assistance F
21. Sensor EGR Vacuum Regulator EVR Solenoid Camshaft Position Sensor CMP Canister Vent Solenoid Alternator Voltage Regulator PB d Not Used o Ea RABS Diode 2 Electronic Engine Controls Diode Mini Fuses Maxi Fuses melee Rete BLOM TR o ze 146 Roadside emergencies CHANGING THE TIRES If you get a flat tire while driving do not apply the brake heavily Instead gradually decrease your speed Hold the steering wheel firmly and slowly move to a safe place on the side of the road Temporary spare tire information Your vehicle may have a temporary or conventional spare tire The temporary spare tire for your vehicle is labeled as such It is smaller than a regular tire and is designed for emergency use only Replace this tire with a full size tire as soon as possible It is not recommended that the vehicle be operated in 4WD modes with a temporary spare If 4WD operation is necessary do not operate above speeds of 16 km h 10 mph or for distances above 80 km 50 miles If you use the temporary spare tire continuously or do not follow these precautions the tire could fail causing you to lose control of the vehicle possibly injuring yourself or others When driving with the temporary spare tire do not e exceed 80 km h 50 mph under any circumstances e load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label e tow a trailer e use tire chains e drive through an automat
22. Severe climates If you drive in extremely cold climates less than 36 C 34 F it may be necessary to increase the coolant concentration above 50 NEVER increase the coolant concentration above 60 increased engine coolant concentrations above 60 will decrease the overheat protection characteristics of the engine coolant and may cause engine damage refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months If you drive in extremely hot climates it is still necessary to maintain the coolant concentration above 40 NEVER decrease the coolant concentration below 40 decreased engine coolant concentrations below 40 will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage decreased engine coolant concentrations below 40 will decrease the freeze protection characteristics of the engine coolant and may cause engine damage refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive Vehicles driven year round in non extreme climates should use a 50 50 mixture of engine coolant and distilled water for optimum cooling system and engine protection 172 Maintenance and care CHECKING AND ADDING POWER STEERING FLUID Check
23. a heavy load 125 LOCATION ooo eecceeeceetcceeeseeeeeenees 125 GVWR Gross Vehicle Weight Rating 125 Calculating sirosis 125 127 GEDMILION sisveesisscdevedes eestor ceees 125 driving with a heavy load 125 locati ON escenes 125 Hazard flashers ssrrisessscesesssss 138 Headlamps cccccccessceeesseeeeees 18 AMINE searen niae 202 bulb specifications 000 201 daytime running lights 18 TASH to PASS asccssscvessevsesciscdasedeets 19 high BEAM cccccscsscasvesssceccdeasse 11 18 replacing bulbs 0 0 197 turning on and off sesser 18 warning Chime ceeeeees 13 Heating serere veteran eesecesvtanaay 19 heater only system cccee 19 TI GOO EE A E 159 TSTULION seimeni 214 215 positions of the ignition 54 Infant seats see Safety seats 94 Inspection maintenance I M COSTING voses oni tees anaa 196 Instrument panel CLEANING sincerer nn 207 CHISTED percen 8 207 lighting up panel and interior 006 19 location of components 8 Jump starting your vehicle 152 Keys key in ignition chime 13 positions of the ignition 54 Lamps bulb replacement specifications chart 201 Cargo lamps sererarrrercn iiai 19 daytime running light 18 fog lamps sererai 18 headlamps senserint 18 headlamps flash to pass 19 instrument panel dimming 19 interio
24. ad For information on the SRS warning chime refer to the Seating and safety restraints chapter Key in ignition warning chime Sounds when the key is left in the ignition in the OFF LOCK or ACC position and the driver s door is opened Headlamps on warning chime Sounds when the headlamps or parking lamps are on the ignition is off and the key is not in the ignition and the driver s door is opened 13 Instrumentation GAUGES Standard instrument cluster gauges Fuel gauge Displays approximately how much lt 1 fuel is in the fuel tank when the FUEL DOOR key is in the ON position The fuel gauge may vary slightly when the vehicle is in motion The ignition should be in the OFF position while the vehicle is being refueled When the gauge first indicates empty there is a small amount of reserve fuel in the tank When refueling the 14 Instrumentation vehicle from empty indication the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel The FUEL DOOR icon and arrow indicates which side of the vehicle the fuel filler door is located Engine coolant temperature gauge Indicates the temperature of the engine coolant At normal operating temperature the needle remains within the normal area the area I H between the H and C If it enters the red section the engine is overheating Stop
25. and attaches to an anchoring point Other manufacturers offer the tether strap as an accessory Contact the manufacturer of your child safety seat for information about ordering a tether strap In Super Cabs equipped with Center Facing Jump Seats the tether strap anchor bracket should be installed only at the center of the cab s back panel with the child seat in the front center seating position Installing an anchor bracket at the right rear of the cab may increase risk of injury to an occupant of the right rear center facing jump seat in the event of a collision or a sudden stop If a tether child seat is installed in the right front seating position secure the tether strap to the webbing of the buckled right rear lap belt You can attach a tether strap anchor bracket to the cab inner back panel by using a tether anchor kit 613D20 available at no charge from any Ford dealer f Do not install a child seat in a center facing jump seat Tether anchorage hardware Tether anchorage hardware kits part number 613D20 including instructions may be obtained at no charge from any Ford or Lincoln Mercury dealer Tighten the anchor according to specifications Otherwise the safety seat may not be properly secured and the child may be injured in a sudden stop or collision 99 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system This system meets all Canadian Interference Causing
26. condition 2 Child age 12 or under A child age 12 or under must ride in the front seat because e my vehicle has no rear seat e although children age 12 and under ride in the rear seat whenever possible children age 12 and under have no option but to sometimes ride in the front seat because rear seat space is insufficient or e the child has a medical condition that according to the child s physician makes it necessary for the child to ride in the front seat so that the driver can monitor the child s condition 3 Medical condition A passenger has a medical condition that according to his or her physician e poses a special risk for the passenger if the air bag deploys and e makes the potential harm from the passenger air bag deployment greater than the potential harm from turning OFF the air bag and experiencing a crash without the protection offered by the air bag This vehicle has special energy management safety belts for the driver and or right front passenger These particular belts are specifically designed to work with air bags to help reduce the risk of injury in a collision The energy management safety belt is designed to give or release additional belt webbing in some accidents to reduce concentration of force on an occupant s chest and reduce the risk of certain bone fractures and injuries to underlying organs In a crash if the air bag is turned OFF this energy management safety belt might permit the pers
27. cooling system never remove the radiator cap while the engine is running or hot Failure to follow this warning may result in damage to the engine s cooling system and possible severe personal injury If you must remove the radiator cap follow these steps to avoid personal injury 1 Before you remove the cap turn the engine off and let it cool 2 When the engine is cool wrap a thick cloth around the cap Slowly turn cap counterclockwise until pressure begins to release 3 Step back while the pressure releases 4 When you are sure that all the pressure has been released use the cloth to turn it counterclockwise and remove the cap Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford approved processes Not all coolant recycling processes produce coolant which meets Ford specification ESE M97B44 A Use of a recycled engine coolant which does not meet the Ford specification may harm engine and cooling system components Always dispose of used automotive fluids in a responsible manner Follow your community s regulations and standards for recycling and disposing of automotive fluids 171 Maintenance and care Coolant refill capacity To find out how much fluid your vehicle s cooling system can hold refer to Refill capacities in the Capacities and specifications chapter Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter
28. engine coolant in the windshield washer fluid reservoir If engine coolant is sprayed onto the windshield it could make it difficult to see through the windshield When the engine is cool add a 50 50 mixture of engine coolant and distilled water to the engine coolant reservoir until the coolant is at the cold fill level or within the cold fill range as listed in the engine coolant reservoir depending upon application e NEVER increase the coolant concentration above 60 e NEVER decrease the coolant concentration below 40 e Engine coolant concentrations above 60 or below 40 will decrease the freeze protection characteristics of the engine coolant and may cause engine damage 170 Maintenance and care Plain water may be added in an emergency but you must replace it with a 50 50 mixture of engine coolant and distilled water as soon as possible Check the coolant level in the reservoir before you drive your vehicle the next few times with the engine cool If necessary add a 50 50 mixture of engine coolant and distilled water to the engine coolant reservoir until the coolant level is at the cold fill level or within the cold fill range as listed on the reservoir depending upon application Have your dealer check the engine cooling system for leaks if you have to add more than 1 0 liter 1 0 quart of engine coolant per month To avoid scalding hot steam or coolant from being released from the engine
29. ints cseccienaxbetaveteadiarseieseevess 217 Vehicle loading sirsenis 125 camper bodies oo eee eeeeeees 136 Ventilating your vehicle 105 Warning Chimes cceeeeees 13 Warning lights see Lights 8 Washer fluid oo ceeeeeeeeeeeees 168 Water Driving through 124 Windows DOWEP sisdscctessiahincelceiciarieneicns 61 Windshield washer fluid and wipers checking and adding fluid 168 checking and cleaning 180 ODETALLON scs irns E 61 replacing wiper blades 181 Wrecker towing eseese 157 235 236 237 238 Filling station information Item Required fuel Refer to Octane recommendations in the Maintenance and care chapter cab Short wheel base cab Long wheel base Fuel tank capacity SuperCab 73 8L 19 5 gallons Engine oil capacity includes filter 4 3L 4 5 quarts Use Motorcraft change 2 5L I4 and 3 0L V6 SAE 5W 30 Super Premium Motor engines Oil Ford specification WSS M2C153 G Engine oil capacity includes filter 4 7L 5 0 quarts Use Motorcraft change 4 0L V6 engine SAE 5W 30 Super Premium Motor Oil Ford specification WSS M2C153 G Tire size and pressure Refer to the Certification Label on inside of driver s door o Coolant capacity 2 5L 14 with 10 0L 10 5 quarts manual transmission ie ae Coolant capacity 2 5L 14 with 9 7L 10 2 quarts automatic transmission po l Coolant capacity 3 0L V6 with 14 3L 15 1 qua
30. level Make sure the oil level is not above the MAX mark or the letter F in FULL on the engine oil level indicator dipstick 4 Install the indicator and ensure it is fully seated 5 Fully install the engine oil filler cap by turning the filler cap clockwise until three clicks can be heard To avoid possible oil loss DO NOT operate the vehicle with the engine oil level indicator and or the engine oil filler cap removed 164 Maintenance and care Engine oil and filter recommendations Look for this certification trademark Motorcraft SAE 5W 30 MOTOR OIL QUART 0 946L Use SAE 5W 30 motor oil certified for gasoline engines by the American Petroleum Institute API Motor oil displaying the API certification trademark will meet all requirements for your vehicle s engine Ford oil specification is WSS M2C153 G Do not use supplemental engine oil additives oil treatments or engine treatments They are unnecessary and could under certain conditions lead to engine damage which is not covered by your warranty Change your engine oil and filter according to the appropriate schedule listed in the Scheduled Maintenance Guide Ford production and aftermarket Motorcraft oil filters are designed for added engine protection and long life If a replacement oil filter is used that does not meet Ford material and design specifications start up engine noises or knock may be experienced It is recommended you use th
31. lock brake system is disabled and normal O braking is still effective unless the BRAKE brake warning light also remains illuminated with parking brake released If your brake warning lamp illuminates have your vehicle serviced immediately Using ABS e In an emergency or when maximum efficiency from the ABS is required apply continuous force on the brake The ABS will be activated immediately thus allowing you to retain full steering control of your vehicle and providing there is sufficient space will enable you to avoid obstacles and bring the vehicle to a controlled stop e The Anti Lock system does not decrease the time necessary to apply the brakes or always reduce stopping distance Always leave enough room between your vehicle and the vehicle in front of you to stop e We recommend that you familiarize yourself with this braking technique However avoid taking any unnecessary risks Parking brake P Apply the parking brake whenever the vehicle is parked To set the parking brake press the parking brake pedal down until the pedal stops 108 Driving The BRAKE warning lamp in the instrument cluster illuminates and O remains illuminated when the BRAKE ignition is turned ON until the parking brake is released Always set the parking brake fully and make sure that the gearshift is securely latched in P Park automatic transmission or in 1 First manual transmission The parking brake is not re
32. lock because they are not controlled by RABS A clicking noise and slight pedal pulsation during RABS braking events indicates the RABS is functioning Pedal pulsation coupled with clicking noise while braking under panic conditions on loose gravel wet or snowy roads is normal and indicates proper functioning of the vehicle s RABS If the vehicle has continuous vibration or shudder in the steering wheel while braking the vehicle should be inspected by a qualified service technician The RABS operates by detecting the onset of rear wheel lockup during brake applications and compensating for this tendency RABS warning lamp The 3 warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position If the light does not illuminate momentarily at start up remains on or continues to flash the ABS needs to be serviced 106 Driving With the ABS light on the anti lock brake system is disabled and normal O braking is still effective unless the BRAKE brake warning light also remains illuminated with parking brake released If your brake warning lamp illuminates have your vehicle serviced immediately Using RABS e In an emergency applying full pressure may cause the front wheels to lock If the front brakes lock the vehicle cannot be steered You should apply the brakes with steadily increasing force as if squeezing the brakes If you feel the front wheels begin to lock m
33. on a hill avoid driving crosswise or turning on steep slopes You could lose traction and slip sideways Drive straight up straight down or avoid the hill completely Know the conditions on the other side of a hill before driving over the crest When climbing a steep hill start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started This reduces strain on the engine and the possibility of stalling When descending a steep hill avoid sudden braking Shift to a lower gear when added engine braking is desired When speed control is on and you are driving uphill your vehicle speed may drop considerably especially if you are carrying a heavy load If vehicle speed drops more than 16 km h 10 mph the speed control will cancel automatically Resume speed with accelerator pedal If speed control cancels after climbing the hill reset speed by pressing and holding the SET ACCEL button to resume speeds over 50 km h 30 mph Automatic transmissions may shift frequently while driving up steep grades Eliminate frequent shifting by shifting out of Overdrive into a lower gear Driving on snow and ice A 4WD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle 123 Driving Avoid sudden applications of power and quick changes of direction on snow and ice Apply the accelerator slowly and steadily when starting from a full stop When braking
34. other fuels such as Fuel Methanol may cause powertrain damage a loss of vehicle performance and your warranty may be invalidated Fuel quality Many of the world s automakers issued the World wide Fuel Charter that recommends gasoline specifications to provide improved performance and emission control system protection for your vehicle Gasolines that meet the World wide Fuel Charter should be used when available Ask your fuel supplier about gasolines that meet the World wide Fuel Charter It should not be necessary to add any aftermarket products to your fuel tank if you continue to use high quality fuel of the recommended octane rating Aftermarket products could cause damage to the fuel system Repairs to correct the effects of using an aftermarket product in your fuel may not be covered by your warranty Unleaded Gasoline engines If you are experiencing starting rough idle or hesitation driveability problems during a cold start try a different brand of Regular unleaded 190 Maintenance and care gasoline Premium unleaded gasoline is not recommended particularly in the United States because it may cause these problems to become more pronounced If the problems persist see your dealer or a qualified service technician FFV engine Your FFV will operate well on ordinary Regular unleaded gasoline but only the highest quality fuel ethanol will provide the same level of protection and performance Stan
35. provide after following the steps described above contact the Ford Customer Assistance Center to find an authorized dealership to help you In the United States Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P O Box 6248 Dearborn Michigan 48121 1 800 392 3673 FORD TDD for the hearing impaired 1 800 232 5952 In Canada Customer Assistance Centre Ford Motor Company of Canada Limited P O Box 2000 Oakville Ontario L6J 5E4 1 800 565 3673 FORD 219 Customer assistance If you own a Lincoln vehicle and are away from home when your vehicle needs service or if you need more help than the dealership could provide after following the steps described above contact the Ford Customer Assistance Center to find an authorized dealership to help you In the United States Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P O Box 6248 Dearborn Michigan 48121 1 800 521 4140 TDD for the hearing impaired 1 800 232 5952 In Canada Customer Assistance Centre Ford Motor Company of Canada Limited P O Box 2000 Oakville Ontario L6J 5E4 1 800 565 3673 FORD In order to help you service your Ford or Lincoln Mercury vehicle please have the following information available when contacting a Customer Assistance Center e Your telephone number home and business e The name of the dealer and the city where the dealership is located e The year and make of yo
36. speed underinflation or excessive loading either separately or in combination can cause heat buildup and possible tire failure 182 Maintenance and care SERVICING YOUR TIRES Checking the tire pressure e Use an accurate tire pressure gauge e Check the tire pressure when tires are cold after the vehicle has been parked for at least one hour or has been driven less than 5 km 3 miles e Adjust tire pressure to recommended specifications found on the Certification Label Improperly inflated tires can affect vehicle handling and can fail suddenly possibly resulting in loss of vehicle control Tire rotation Because your vehicle s tires perform different jobs they often wear differently To make sure your tires wear evenly and last longer rotate them as indicated in the Scheduled Maintenance Guide If you notice that the tires wear unevenly have them checked The following procedure applies to vehicles equipped with single rear wheels if your vehicle is equipped with dual rear wheels it is recommended that only the front wheels be rotated side to side e Four tire rotation AN K A L I l 183 Maintenance and care e Five tire rotation JL ae l gt Replacing the tires Replace the tires when the wear band is visible through the tire treads JOS When replacing full size tires never mix radial bias belted or bias type tires Use only the tire sizes that ar
37. system warning light 0 eee 11 Audio system see Radio 26 Automatic transmission 111 driving an automatic OVETATIVE ooo eects 112 114 AIG adding scssicisoreioeseesaess 173 fluid checking 0 eee 173 fluid refill capacities 209 fluid specification 0 0 0 0 214 Auxiliary power point 25 Axle lubricant specifications 212 214 refill capacities 0 ce 209 traction OK wc eeeeeeeeeees 124 Battery ccccccscccsssseseesesteeeeees 178 acid treating emergencies 178 charging system warning light sssrinin 11 jumping a disabled battery 152 maintenance free ccce 178 replacement specifications 209 SOLVICINIS soirassa 178 Voltage gauge eecisrorerssisecsos 17 Belt minder ccccescceeesseeeees 80 Bi ak ysseiscsiscassaascteesiaantsaesseexseans 106 anti lock n se 106 107 108 anti lock brake system ABS warning light eeeee 10 108 brake warning light 10 fluid checking and adding 166 fluid refill capacities 209 fluid specifications 212 214 lubricant specifications 212 214 PARINE seie a E E 108 shift interlock ceeeeee 111 Break in period cccceeseeeeeees 2 Capacities for refilling fluids 209 Cargo area Shade cceeeeeeees 63 Cargo Heb ve caccavszessercesselansneedateesy 63 Certification Label 00 217 Child safety restrain
38. the EJ control to stop and eject a CD Dolby noise reduction Dolby noise reduction operates in tape mode Dolby noise reduction __ __ __ gt reduces the amount of hiss and static during tape playback Press the BO control to activate and deactivate the Dolby noise reduction Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation Dolby and the double D symbol OO are trademarks of Dolby Laboratories Licensing Corporation Compression adjust Compression adjust brings soft and loud CD passages together for a a ee more consistent listening level gt Press the COMP control to activate and deactivate compression adjust Shuffle feature The shuffle feature operates in CD mode if equipped and plays all tracks on the current disc in random order If equipped with the CD changer the shuffle feature continues to the next disc after all tracks on the current disc are played Press the SHUFFLE control to start this feature Random order play will continue until the SHUFFLE control is pressed again 50 Setting the clock To set the hour press and hold the CLK control and press SEEK A to decrease hours and to increase hours To set the minute press and hold the CLK control and press TUNE lt d to decrease minutes and p gt to increase minutes If your vehicle has a separate clock module other than the digital radi
39. the correct service interval 2 Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface 3 Indicates only approximate dry fill capacity Some applications may vary based on cooler size and if equipped with an in tank cooler The amount of transmission fluid and fluid level should be set by the indication on the dipstick s normal operating range 4 Use Ford Premium Engine Coolant green in color DO NOT USE Ford Extended Life Engine Coolant orange in color Refer to Adding engine coolant in the Maintenance and Care chapter 5 Traction Lok axles use 2 2 2 4L 4 75 5 0 pints of rear axle lubricant Add 118 ml 4 oz of Additive Friction Modifier C8AZ 19B546 A or equivalent meeting Ford specification EST M2C118 A for complete refill of Traction Lok axles Service refill capacities are determined by filling the rear axle 6 mm to 14 mm 1 4 inch to 9 16 inch below the bottom of the filler hole 211 Capacities and specifications LUBRICANT SPECIFICATIONS Item nti fi Ford part Ford equivalent number specification Motorcraft SAE XY 80W90 QL WSP M2C197 A Front axle 80W 90 4X4 Premium Rear Axle Lubricant Motorcraft SAE XY 80W90 QL WSP M2C197 A 80W 90 Premium Rear Axle Lubricant High C6AZ 19542 AB ESA M6C25 A Brake fluid and _ Performance and DOT 3 clutch fluid Gf DOT 3 Motor equipped Vehicle Brake Fluid Door weather Silicone
40. the dealer s and Ford Motor Company e the names if known of all the people you contacted at the dealership s e a description of the action you expect to resolve your concern You will receive a letter of explanation if your application does not qualify for Board review Oral presentations If you would like to make an oral presentation indicate YES to question 6 on the application While it is your right to make an oral presentation before the Board this is not a requirement and the Board will decide the case whether or not an oral presentation is made Oral presentation may be requested by the Board as well Making a decision Board members review all available information related to each complaint including oral presentations and arrive at a fair and impartial decision Board review may be terminated at any time by either party Every effort is made to decide the case within 40 days of the date that all requested information is received by the Board Since the Board generally meets once a month it may take longer for the Board to consider some cases After a case is reviewed the Board mails you a decision letter and a form on which to accept or reject the Board s decision The decisions of the Board are binding on Ford and in some cases on the dealer but not on consumers who are free to pursue other remedies available to them under state or federal law To Request a DSB Brochure Application For a brochure app
41. the power steering fluid l S Refer to the Scheduled Maintenance Lt eS A q Z Guide for the service interval AATA schedules If adding fluid is C necessary use only MERCON ATF fN 1 Start the engine and let it run until it reaches normal operating temperature the engine coolant temperature gauge indicator will be near the center of the normal area between H and C 2 While the engine idles turn the steering wheel left and right several times 3 Turn the engine off 4 Check the fluid level on the dipstick It should be between the arrows in the FULL HOT range Do not add fluid if the level is within this range 5 If the fluid is low add fluid in small amounts continuously checking the level until it reaches the FULL HOT range Be sure to put the dipstick back in the reservoir TRANSMISSION FLUID Checking automatic transmission fluid Refer to your Scheduled Maintenance Guide for scheduled intervals for fluid checks and changes Your transmission does not consume fluid However the fluid level should be checked if the transmission is not working properly i e if the transmission slips or shifts slowly or if you notice some sign of fluid leakage Automatic transmission fluid expands when warmed To obtain an accurate fluid check drive the vehicle until it is at normal operating temperature approximately 30 km 20 miles If your vehicle has been 173 Maintenance and care operated for an extended per
42. the top cruise gear and with steady pressure on the gas pedal e Four wheel drive operation if equipped is less fuel efficient than two wheel drive operation e Close windows for high speed driving EPA window sticker Every new vehicle should have the EPA window sticker Contact your dealer if the window sticker is not supplied with your vehicle The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles It is important to note the box in the lower left corner of the window sticker These numbers represent the Range of L 100 km MPG expected on the vehicle under optimum conditions Your fuel economy may vary depending upon the method of operation and conditions EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards To make sure that the catalytic converter and other emission control components continue to work properly e Use only unleaded fuel or E85 if equipped with the 3 0L FFV V6 engine e Avoid running out of fuel e Do not turn off the ignition while your vehicle is moving especially at high speeds Have the items listed in your Scheduled Maintenance Guide performed according to the specified schedule The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to the life and performance of your
43. times to dry them Waxing your vehicle Waxing your vehicle on a regular basis will reduce minor scratches and paint damage Wax when water stops beading on the surface This could be every three or four months depending on operating conditions Use only carnauba or synthetic based waxes Use a cleaning fluid with a clean cloth to remove any bugs before waxing your vehicle Use tar remover to remove any tar spots Avoid getting wax on the windshield or on any surfaces which appear coarse or bumpy If you have wax applied at a commercial car wash it is 203 Maintenance and care recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield Repairing paint chips Minor scratches or paint damage from road debris may be repaired with the Ultra Touch Prep and Finishing Kit F7AZ 19K507 BA Lacquer Touch up Paint HALBZ 19500 XXXXA or Exterior Acrylic Spray Lacquer HALAZ 19500 XXXXA from the Ford Car Care Chemicals line Please note that the part numbers shown as XXXX above will vary with your vehicle s specific coloring Observe the application instructions on the products Remove particles such as bird droppings tree sap insect remains tar spots road salt and industrial fallout immediately Cleaning the wheels Wash with the same detergent as the body of your vehicle Do not use acid based or alcohol based wheel cleaners steel wool fuel or strong detergent
44. to keep all four wheels on the most solid area of the trail Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain Apply the accelerator slowly and avoid spinning the wheels Mud and water If you must drive through high water drive slowly Traction or brake capability may be limited When driving through water determine the depth avoid water higher than the bottom of the hubs if possible and proceed slowly If the ignition system gets wet the vehicle may stall Once through water always try the brakes Wet brakes do not stop the vehicle as effectively as dry brakes Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal 122 Driving After driving through mud clean off residue stuck to the driveshafts and tires Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components If the transmission transfer case or front axle are submerged in water their fluids should be checked and changed if necessary Water intrusion into the transmission may damage the transmission Replace rear axle lubricant any time the axle has been submerged in water The rear axle does not normally require a lubricant change for the life of the vehicle Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair is required Driving on hilly or sloping terrain When driving
45. when the engine coolant CHECK temperature is high the engine oil pressure is low or the fuel gauge is GAGE at or near empty The ignition must be in the ON position for this lamp to illuminate The lamp will also illuminate when the ignition is turned to the ON position Refer to Engine coolant temperature gauge Engine oil pressure gauge or Fuel gauge in this chapter for more information Four wheel drive low if equipped Momentarily illuminates when the 4 WD ignition is turned to the START position Iuminates when LOW four wheel drive low is engaged If the light continues to flash have the system serviced Four wheel drive high if equipped Momentarily illuminates when the 4 WD ignition is turned to the START position Illuminates when four HIGH wheel drive high is engaged If the light continues to flash have the system serviced Door ajar Illuminates when the ignition is in the ON or START position and any DOOR door is open AJAR Speed control This light comes on when either the SET ACCEL or RESUME controls SPEED are pressed It turns off when the CONT speed control OFF control is pressed the brake is applied or the ignition is turned to the OFF position 12 Instrumentation Safety belt warning chime A Sounds to remind you to fasten your safety belts For information on the safety belt warning chime refer to the Seating and safety restraints chapter Supplemental restraint system SRS warning chime
46. will not before the ignition switch is turned activate to the ON position The purpose of the Belt Minder is to remind occasional wearers to wear safety belts all of the time 80 Seating and safety restraints The following are reasons most often given for not wearing safety belts All statistics based on U S data Reasons given Consider Crashes are rare 36 700 crashes occur every day The more we events drive the more we are exposed to rare events even for good drivers 1 in 4 of us will be seriously injured in a crash during our lifetime Tm not going far 3 of 4 fatal crashes occur within 25 miles of home Belts are Ford designs its safety belts to enhance comfort If uncomfortable you are uncomfortable try different positions for the safety belt upper anchorage and seatback which should be as upright as possible this can improve comfort I was in a hurry Prime time for an accident Belt Minder reminds us to take a few seconds to buckle up Seat belts don t Safety belts when used properly reduce risk of work death to front seat occupants by 45 in cars and by 60 in light trucks Traffic is light Nearly 1 of 2 deaths occur in single vehicle crashes many when no other vehicles are around Belts wrinkle my Possibly but a serious crash can do much more clothes than wrinkle your clothes particularly if you are unbelted The people I m Set the exampl
47. your area improves the performance of your vehicle Cold starting performance can also be improved with the use of an engine block heater The engine block heater is available as a Ford option and can also be obtained from your Ford dealer Consult the engine block heater section for proper use of the engine block heater If you should experience cold weather starting problems on Hq 85 ethanol and neither an alternative brand of E4 85 ethanol nor an engine block heater is available the addition of unleaded gasoline to your tank will improve cold starting performance Your vehicle is designed to operate on E4 85 ethanol alone unleaded gasoline alone or any mixture of the two 103 Starting If the engine fails to start using the preceding instructions 1 Press the accelerator pedal 1 3 to 1 2 of the way to floor and hold 2 Turn the key to START position 3 When the engine starts release the key then release the accelerator pedal gradually as the engine speeds up 4 If the engine still fails to start repeat steps one through three 5 After the engine starts hold your foot on the brake pedal put the gearshift lever in gear and release the parking brake Slowly release the brake pedal and drive away in a normal manner Using the engine block heater if equipped An engine block heater warms the engine coolant which improves starting warms up the engine faster and allows the heater defroster system to respond quic
48. 25 seconds or when the ignition is turned to the RUN or ACC position The dome lamp control Cif equipped must not be set to the OFF position for the illuminated entry system to operate The inside lights will not turn off if e they have been turned on with the dimmer control or e any door is open The battery saver will shut off the interior lamps 40 minutes after the ignition has been turned to the OFF position SECURILOCK PASSIVE ANTI THEFT SYSTEM IF EQUIPPED The SecuriLock passive anti theft system provides an advanced level of vehicle theft protection Your vehicle s engine can only be started with the two special SecuriLock electronically coded keys provided with your vehicle Each time you start your vehicle the SecuriLock key is read by the SecuriLock passive anti theft system If the SecuriLock key identification code matches the code stored in the SecuriLock passive anti theft system the vehicle s engine is allowed to start If the SecuriLock key identification code does not match the code stored in the system or if a SecuriLock key is not detected vehicle theft situation the vehicle s engine will not operate If there is any potential SecuriLock anti theft problem with your vehicle ensure ALL SecuriLock keys for that vehicle are brought to the dealership to aid in troubleshooting The SecuriLock passive anti theft system is not compatible with aftermarket remote start systems Use
49. 4WD control to the 4X4 HIGH or 4X4 LOW position Driving off road with 4WD Your vehicle is specially equipped for driving on sand snow mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles both on and off the road 121 Driving Maintain steering wheel control at all times especially in rough terrain Since sudden changes in terrain can result in abrupt steering wheel motion make sure you grip the steering wheel from the outside Do not grip the spokes Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps You should either know the terrain or examine maps of the area before driving Map out your route before driving in the area For more information on driving off road read the Four Wheeling supplement in your owner s portfolio If your vehicle gets stuck If the vehicle is stuck it may be rocked out by shifting from forward and reverse gears stopping between shifts in a steady pattern Press lightly on the accelerator in each gear Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat Do not spin the wheels at over 56 km h 85 mph The tires may fail and injure a passenger or bystander Sand When driving over sand try
50. 64 6 000 0 2 400 50 3 0L 4 10 2 721 0 1 089 4 64 6 000 0 2 400 50 3 73 13175 0 1 515 4 64 7 000 0 3 340 50 4 0L 4 10 3 175 0 1 515 4 64 7 000 0 3 340 50 3 73 4 10 3 73 4 10 4 0L SuperCab 2 721 0 998 6 000 0 2 200 2 721 0 998 6 000 0 2 200 50 3 50 4 64 3 0L 4 64 3 175 0 1 433 4 64 7 000 0 3 160 50 3 175 0 1 433 4 64 7 000 0 3 160 50 For high altitude operation reduce GCW by 2 per 300 meters 1 000 ft of elevation For definition of terms used in this table see Vehicle loading earlier in this chapter To determine maximum trailer weight designed for your vehicle see Calculating the load earlier in this chapter Maximum trailer weight is shown The combined weight of the completed towing vehicle including hitch passengers and cargo and the loaded trailer must not exceed the Gross Combined Weight Rating GCWR OL 4 0L OL 4 129 Driving Trailer towing table 4x2 automatic transmission Maximum Maximum Maximum GCWR kg trailer frontal area of Cbs weight kg lbs trailer m ft 0 maximum Regular Cab 4x2 2 5L 4 10 2 494 0 989 Equal to frontal 5 500 2 180 area of base vehicle 3 0L 3 73 13 401 0 1 869 4 64 7 500 0 4 120 50 4 10 3 401 0 1 842 4 64 7 500 0 4 060 50 4 0L 3 55 4309 0 2 749 4 64 9 500 0 6 060 50 SuperCab 4x2 3 0L 3 73 13 0 1 778 4 64 7 500 0 3 920 50 4 0L 3 55 64 50
51. C TRANSMISSION OPERATION IF EQUIPPED Brake shift interlock This vehicle is equipped with a brake shift interlock feature that prevents the gearshift lever from being moved from P Park when the ignition is in the ON position unless brake pedal is depressed If you cannot move the gearshift lever out of P Park with ignition in the ON position and the brake pedal depressed 1 Apply the parking brake turn ignition key to LOCK then remove the key 2 Insert the key and turn it to OFF Apply the brake pedal and shift to N Neutral 3 Start the vehicle If it is necessary to use the above procedure to move the gearshift lever it is possible that a fuse has blown or the vehicle s brakelamps are not operating properly Refer to Fuses and relays in the Roadside emergencies chapter Do not drive your vehicle until you verify that the brakelamps are working If your vehicle gets stuck in mud or snow it may be rocked out by shifting from forward and reverse gears stopping between shifts in a steady pattern Press lightly on the accelerator in each gear Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat Always set the parking brake fully and make sure the gearshift is latched in P Park Turn off the ignition whenever you
52. Contents Before driving Introduction 2 Instrumentation 6 Controls and features 18 Seating and safety restraints 70 Starting and driving Starting 100 Driving 106 Roadside emergencies 137 Servicing Maintenance and care 158 Capacities and specifications 209 Customer assistance 218 Reporting safety defects 230 Index 231 All rights reserved Reproduction by any means electronic or mechanical including photocopying recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company Ford may change the contents without notice and without incurring obligation Copyright 1999 Ford Motor Company Introduction The following warning may be required by California law CALIFORNIA Proposition 65 Warning Engine exhaust some if its constituents and certain vehicle components contain or emit chemicals known to the State of California to cause cancer or birth defects or other reproductive harm ICONS Indicates a safety alert Read the following section on Warnings Indicates vehicle information related to recycling and other environmental concerns will follow Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment Indicates a message regarding child safety restraints Refer to Seating CO and safety restraints for more infor
53. D changer Play will begin on the first track of the disc unless the CD changer is in y shuffle mode Refer to Shuffle feature for more information Hold the control to continue reversing through the disc e Press B gt to select the next disc in the CD changer Hold the control to fast forward through the remaining discs Seek function The seek function control works in radio or CD mode Seek function in radio mode e Press lt q to find the next listenable station down the frequency band lt 4 Ns p e Press to find the next DISCS listenable station up the frequency band Seek function for CD mode e Press lt Q to seek to the previous track of the current disc If a selection has been playing for TUNE three seconds or more and you lt DISCS gt press lt q the CD changer will replay that selection from the beginning e Press gt to seek forward to the next track of the current disc After the last track has been completed the first track of the current disc will automatically replay Scan function The scan function works in radio or CD mode 39 Controls and features Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band Press the SCAN control again to stop the scan mode Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD The CD scans in a forward direction wrapping b
54. F7AZ 19G208 BA ESR M13P4 A strips Lubricant Engine coolant Ford Premium EH2FZ 19549 AA ESE M97B44 A Engine Coolant in Canada Motorcraft CXC 8 B Motorcraft SAE XO 5W380 QSP WSS M2C153 G 5W 30 Super and API Premium Motor Certification Oil Mark Hinges door Multi Purpose DOAZ 19584 AA ESB M1C93 B or checks latches Grease or ESB M1C159 A striker plates F5AZ 19G209 AA fuel filler door hinge and seat tracks Rear axle Engine oil 212 Capacities and specifications Item ec pea Ford part Ford equivalent number specification Transmission Premium ESA M1C75 B steering parking Long Life Grease XG 1 K brake linkages and pivots brake and clutch pedal shaft clutch pilot bearing and input shaft spline manual transmission Power steering Motorcraft XT 2 QDX MERCON fluid transfer MERCON ATF case fluid 4X4 and transmission fluid manual Automatic Motorcraft XT 5 QM transmission MERCON V 4R44E 5R44E ATF 2 MERCON V and 5R55E Ultra clear C9AZ 19550 AC ESR M17P5 A Windshield Windshield washer fluid Washer Concentrate 1 Add 118 ml 4 oz of Additive Friction Modifier C8AZ 19B546 A or equivalent meeting Ford specification EST M2C118 A for complete refill of Traction Lok axles 2 Ensure the correct automatic transmission fluid is used Transmission fluid requirements are indicated on the dipstick or on the dipstick handle MERCON and MERCON V are not interc
55. Motorcraft 4x2 vehicles with 9 4L MERCON V automatic and 2 5L 9 9 quarts ATF I4 engine 4x2 vehicles with 9 5L automatic and 3 0L 10 0 quarts or 4 0L V6 engine 4x4 vehicles with 9 8L automatic 10 3 quarts Premium Engine 2 5L 14 engine with 10 0L Coolant manual 10 5 quarts transmission 2 5L I4 engine with 9 7L automatic 10 2 quarts transmission 3 0L V6 engine with 14 3L manual 15 1 quarts transmission 3 0L V6 engine with 14 0L automatic 14 8 quarts transmission 4 0L V6 engine with 13 0L manual 13 7 quarts transmission 4 0L V6 engine with 12 5L automatic 13 2 quarts transmission Fuel tank N A Regular cab Short 62 4L wheel base 16 5 gallons Regular cab Long 75 7L wheel base 20 0 gallons SuperCab 73 8L 19 5 gallons Transfer Motorcraft 4x4 Vehicles 1 2L Case Fluid MERCON ATF 1 25 quarts 210 Capacities and specifications Fluid Ford Part Application Capacity Name Front axle Motorcraft SAE 4x4 Vehicles 1 7L 8 6 pints lubricant 80W 90 Premium Rear Axle Lubricant Rear axle Motorcraft SAE 2 4 2 5L lubricant 80W 90 5 0 5 3 pints Premium Rear Axle Lubricant Windshield Ultra Clear 2 6L washer fluid Windshield 2 75 quarts Washer Concentrate 1 Ensure the correct automatic transmission fluid is used MERCON and MERCON V are not interchangeable DO NOT MIX MERCON and MERCON V Refer to the Scheduled Maintenance Guide to determine
56. P decisions are fast fair and final the arbitrator s award is binding both to you and Ford of Canada CAMVAP services are available in all territories and provinces except Quebec For more information without charge or obligation call your CAMVAP Provincial Administrator directly at 1 800 207 0685 GETTING ASSISTANCE OUTSIDE THE U S AND CANADA Before exporting your vehicle to a foreign country contact the appropriate foreign embassy or consulate These officials can inform you of local vehicle registration regulations and where to find unleaded fuel If you cannot find unleaded fuel or can only get fuel with an anti knock index lower than is recommended for your vehicle contact a district or owner relations customer assistance office 224 Customer assistance The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage Ford Motor Company Ford of Canada is not responsible for any damage caused by use of improper fuel In the United States using leaded fuel may also result in difficulty importing your vehicle back into the U S If your vehicle must be serviced while you are traveling or living in Central or South America the Caribbean or the Middle East contact the nearest Ford dealership If the dealership cannot help you write or call FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fair
57. POINT 12V CI gt C mi C gt lt T_T CoO gt IC I la cy gt lt COo I gt I lt E K y K UUUUUU O03 OOOO Tee cae The auxiliary power point is located on the instrument panel This outlet should be used in place of the cigarette lighter for optional electrical accessories PASSENGER AIR BAG ON OFF SWITCH This switch must be used to deactivate the passenger air bag O whenever a child seat is used in the ON right front or center front passenger seat position Refer to Passenger OFF air bag ON OFF switch in the Seating and safety restraints chapter PASSENGER AIRBAG 25 Controls and features USING YOUR AUDIO SYSTEM AM FM Stereo lt SEEK p gt lt TUNE gt Volume power control Press the control to turn the audio system on or off S lt on See Turn the control to raise or lower volume x 26 Controls and features If the volume is set above a certain level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition switch is turned back on AM FM select The AM FM select control works in radio mode AM FM AM FM select in radio mode This control allows you to select AM or FM frequency bands Press
58. S 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation 64 Controls and features Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Replacing the battery The transmitter is powered by one coin type three volt lithium battery CR2032 or equivalent Typical operating range will allow you to be up to 10 meters 33 feet away from your vehicle A decrease in operating range can be caused by weather conditions nearby radio towers structures around the vehicle other vehicles parked next to the vehicle To replace the battery 1 halves of the transmitter near the key ring DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART 2 battery in the same orientation Refer to the diagram inside the transmitter unit 3 together Twist a thin coin between the two Place the positive side of new Snap the two halves back 65 Controls and features Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle s memory or you would like to purchase additional remote transmitters and have them programmed to your vehicle e Take all your vehicle s
59. UNE gt Scan function The scan function works in radio as tape or CD mode Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band Press the control again to stop the scan mode iN oO Controls and features Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape The tape scans in a forward direction At the end of the tape s first side direction automatically reverses to the opposite side of the tape To stop on a particular selection press the control again Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD The CD scans in a forward direction wrapping back to the first track at the end of the CD To stop on a particular selection press the control again Radio station memory preset The radio is equipped with six station memory preset controls These controls can be used to select up to six preset AM stations and twelve FM stations six in FM1 and six in FM2 Setting memory preset siations 1 Select the frequency band with the AM FM select control 2 Select a station Refer to Tune adjust or Seek function for more information on selecting a station p 3 Press and hold a memory preset control until the sound returns indicating the station is held in memory on the control you selected Autoset memory preset Autose
60. Upholstery Cleaner not available in Canada Ford Metal Surface Cleaner Ford Multi Purpose Cleaner Motorcraft Car Wash Concentrate Motorcraft Carlite Glass Cleaner Ford Spot and Stain Remover Ford Super Premium Tire and Trim Dressing Ford Triple Clean Ford Ultra Clear Spray Glass Cleaner not available in Canada May be sold with the Motorcraft name FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford accessories are available for your vehicle through your local authorized Ford Lincoln Mercury or Ford of Canada dealer These quality accessories have been specifically engineered to fulfill your automotive needs they are custom designed to complement the style and aerodynamic appearance of your vehicle In addition each accessory is made from high quality materials and meets or exceeds Ford s rigid engineering and safety specifications Ford accessories are warranted for up to 12 months or 20 000 km 12 000 miles on all cars and light trucks and 12 months with unlimited distance on medium heavy duty trucks unless the accessory is installed on a new vehicle then the warranty becomes the balance of the new vehicle s warranty or the accessories warranty whichever is greater See your dealer for complete warranty information and availability Not all accessories are available for all models 226 Customer assistance Vehicle Security Styled wheel protector locks Vehicle security systems Comfort and convenience Car
61. ack to the first track at the end of the CD To stop on a particular selection press the control again Bass adjust The bass adjust control allows you to increase or decrease the audio system s bass output Treble adjust The treble adjust control allows you to increase or decrease the audio system s treble output Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers 40 TREB Controls and features Speaker fade adjust Speaker sound can be adjusted between the front and rear A speakers FADE y CD select e To begin CD play if CD s are loaded press the CD control The first track of the disc will begin playing After that CD play will begin where it stopped last Rewind The rewind control works in CD mode To rewind in CD mode press the 44 CD CD control preset 1 1 Press the control again to deactivate rewind mode Fast forward The fast forward control works in CD mode To fast forward in CD changer mode press the CD control preset 2 Press the control again to deactivate fast forward mode Eject function Press the control to stop and eject a cb 41 Controls and features Compression feature Compression adjust brings soft and loud CD passages together for a comp more consistent listening level Press the COMP control to activate and deactivate compression adjust Shuffle feature if equipped
62. afety belts in the Maintenance and care section 83 Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM SRS Your vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity This information will assist Ford in the servicing of your vehicle and may help Ford better understand real world collisions and further improve the safety of future vehicles Important supplemental restraint system SRS precautions The supplemental restraint system is designed to work with the safety a belt to help protect the driver and right front passenger from certain upper body injuries Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module KSN All occupants of the vehicle including the driver should always properly wear their safety belts even when an air bag SRS is provided 84 Seating and safety restraints National Highway Traffic Safety Administration NHTSA recommends a minimum distance of at least 25 cm 10 inches between an occupant s chest and the driver air bag module Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries
63. ake a further check for leaks in the fuel system 139 Roadside emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working a fuse may have blown Blown fuses are identified by a broken wire within the fuse Check the appropriate fuses before replacing any electrical components Always replace a fuse with one that has the specified amperage rating Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire Standard fuse amperage rating and color COLOR Standard Fuse Link Fuses Cartridge 140 Roadside emergencies Passenger compartment fuse panel The fuse panel is located on the left hand side of the instrument panel facing the driver s side door Pull the panel cover outward to access the fuses To remove a fuse use the fuse puller tool provided on the fuse panel cover ge a Jee Ibs Ib4 1 Ls ILe JL7 Ile EHET EN EA Lis Lia Les Lre 7 Lie Lie 20 La Le Les Laa Les Lee L2 L2 2 Cso Ls Le e E 141 Roadside emergencies The fuses are coded as follows Location Rating Fuse Panel Description Blower Motor Relay PAD Module Air Bag Diagnostic Monitor Not Used S A A 7 5A Speed Control Servo Amplifier Assembly Generic Electronic Module GEM Shift Lock Actuator Blend Door Actuator A A A C Heater Assembly Turn Signals 0 5 0 Ins
64. apply the brakes as you normally would In order to allow the anti lock brake system ABS to operate properly keep steady pressure on the brake pedal Allow more stopping distance and drive slower than usual Consider using one of the lower gears TRACTION LOK AXLE IF EQUIPPED This axle provides added traction on slippery surfaces particularly when one wheel is on a poor traction surface Under normal conditions the Traction Lok axle functions like a standard rear axle Extended use of other than the manufacturer s specified size tires on a Traction Lok rear axle could result in a permanent reduction in effectiveness This loss of effectiveness does not affect normal driving and should not be noticeable to the driver To avoid injury never run the engine with one wheel off the ground such as when changing a tire DRIVING THROUGH WATER Do not drive quickly through standing water especially if the depth is unknown Traction or brake capability may be limited and if the ignition system gets wet your engine may stall Water may also enter your engine s air intake and severely damage your engine If driving through deep or standing water is unavoidable proceed very slowly Never drive through water that is higher than the bottom of the hubs for trucks or the bottom of the wheel rims for cars Once through the water always try the brakes Wet brakes do not stop the vehicle as effectively as dry brakes Drying can be impr
65. area of Cbs weight kg lbs trailer m ft 0 maximum Regular Cab 4x2 2 I7 0 717 Equal to frontal 4 800 0 1 580 area of base vehicle 4 2 177 0 717 Equal to frontal 4 800 0 1 580 area of base vehicle 2 V21 0 1 207 4 6 000 0 2 660 4 4 64 2 721 0 1 179 64 6 000 0 2 600 50 64 k i 10 4 0L 3 55 3175 0 1 633 4 7 000 0 3 600 50 3 73 10 3 73 55 50 SuperCab 4x2 2177 0 617 Equal to frontal 4 800 0 1 360 area of base vehicle 4 2177 0 617 Equal to frontal 4 800 0 1 360 area of base vehicle 2 271 0 1 116 4 64 6 000 0 2 460 50 3 3 175 0 1 542 4 64 7 000 0 3 400 50 For high altitude operation reduce GCW by 2 per 300 meters 1 000 ft elevation For definition of terms used in this table see Vehicle Loading earlier in this chapter To determine maximum trailer weight designed for your particular vehicle see Calculating the load earlier in this chapter 2 2 3 OL OL OL 4 0L 128 Driving Trailer towing table 4x2 manual transmission Maximum trailer weight is shown The combined weight of the completed towing vehicle including hitch passengers and cargo and the loaded trailer must not exceed the Gross Combined Weight Rating GCWR Trailer tow table 4x4 manual transmission Rear Maximum Maximum Maximum axle GCWR kg trailer frontal area of ratio lbs weight kg lbs trailer m ft Regular Cab 3 0L 3 73 12 721 0 1 089 4
66. at a standstill while waiting on a hill These actions may reduce clutch life Parking 1 Apply the brake and shift into N Neutral 2 Engage the parking brake 3 Shift into 1 First 4 Turn the ignition to Off Do not park your vehicle in Neutral it may move unexpectedly and injure someone Use 1 First gear and set the parking brake fully 117 Driving Recommended shift speeds Upshifts when accelerating for best fuel economy Transfer case position if equipped ceili 1 2 14 km h 10 mph 5 km h 4 mph 2 3 32 km h 22 mph 11 km h 9 mph 3 4 50 km h 33 mph 19 km h 13 mph 4 5 Overdrive 71 km h 41 mph 27 km h 17 mph Upshifts when cruising recommended for best fuel economy Shift from Transfer case position if equipped Pees 6kmhdOmp 16 km h 10 mph 6 4 mph 10 km h 8 mph 16 12 mph 26 km h 16 mph Reverse Ensure that the vehicle is at a complete stop before shifting into R Reverse Failure to do so may damage the transmission a Put the gearshift lever into N and wait at least several seconds before shifting into R You can shift into R Reverse only by moving the gearshift lever from left of 3 Third and 4 Fourth gears before you shift into R Reverse This is a special lockout feature that protects you from accidentally shifting into R Reverse when you downshift from 5 Overdrive 118 Driving FOUR WHEEL DRIVE 4WD OPERATION IF EQUIPPED
67. belt under the arm 2 Never swing the safety belt around your neck over the inside shoulder 3 Never use a single belt for more than one person On four door SuperCab vehicles do not open the rear door when the rear seat belt is still buckled Combination lap and shoulder belts 1 Insert the belt tongue into the proper buckle the buckle closest to the direction the tongue is coming ae from until you hear a snap and feel a C it latch Make sure the tongue is a securely fastened in the buckle i 2 To unfasten push the release button and remove the tongue from the buckle N 73 Seating and safety restraints The front outboard safety restraints in the vehicle are combination lap and shoulder belts The front passenger outboard safety belt has two types of locking modes described below Energy Management Feature e This vehicle has a seat belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head on collision This seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner This feature is designed to help reduce the belt force acting on the occupant s chest After any vehicle collision the seat belt system at all outboard seating positions except driver which has no automatic locking retractor feature must be checked by a qualified technician to verify that the automatic
68. commended to stop a moving vehicle However if the normal brakes fail the parking brake can be used to stop your vehicle in an emergency Since the parking brake applies only the rear brakes the vehicle s stopping distance will increase greatly and the handling of your vehicle will be adversely affected Pull the release lever to release the BRAKE brake Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy STEERING Your vehicle is equipped with power steering Power steering uses energy from the engine to help steer the vehicle To prevent damage to the power steering pump e Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running e Do not operate the vehicle with a low power steering pump fluid level If the power steering system breaks down or if the engine is turned off you can steer the vehicle manually but it takes more effort 109 Driving If the steering wanders or pulls the condition could be caused by any of the following e underinflated tire s on any wheel s e high crown in center of road e high crosswinds e wheels out of alignment e loose or worn components in steering linkage PREPARING TO DRIVE YOUR VEHICLE Utility vehicles have a significantly higher rollover rate than other types of vehicles In a rollover crash an unbelted person is significantly more likely t
69. crash greater than the potential harm from turning OFF the air bag and allowing the passenger even if belted to hit the dashboard or windshield in a crash This vehicle has special energy management safety belts for the driver and or right front passenger These particular belts are specifically designed to work with air bags to help reduce the risk of injury in a collision The energy management safety belt is designed to give or release additional belt webbing in some accidents to reduce concentration of force on an occupant s chest and reduce the risk of certain bone fractures and injuries to underlying organs In a crash if the air bag is turned OFF this energy management safety belt might permit the person wearing the belt to move forward enough to incur a serious or fatal injury The more severe the crash and the heavier the occupant the greater the risk is Be sure the air bag is turned ON for any person who does not qualify under the NHTSA deactivation criteria 91 Seating and safety restraints Transport Canada deactivation criteria Canada Only 1 Infant An infant less than 1 year old must ride in the front seat because e my vehicle has no rear seat e the rear seat in my vehicle cannot accommodate a rear facing infant seat or e the infant has a medical condition which according to the infant s physician makes it necessary for the infant to ride in the front seat so that the driver can monitor the infant s
70. crews Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper To change the license plate lamp bulbs 1 Reach behind the rear bumper to locate the bulb socket i 5 2 Twist the socket counterclockwise and remove 3 Pull out the old bulb from socket Z and push in the new bulb i es 4 Install the bulb socket in lamp assembly by turning it clockwise Using the right bulbs Replacement bulbs are specified in the chart below Headlamp bulbs must be marked with an authorized D O T for North America and an E for Europe to assure lamp performance light brightness and pattern and safe visibility The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time 201 Maintenance and care Function Park turn side marker lamps front 9006 HB4 Foglamps Cif equipped Hi mount brakelamp Cargo lamps Rear stop turn tail Rear license plate Backup lamp Dome lamp Map dome SuperCab 0 Cif equipped Map dome Regular 90 Cab Gf equipped 904 All replacement bulbs are clear in color except where noted To replace all instrument panel lights see your dealer REPLACING THE INTERIOR BULBS Check the operation of the following interior bulbs frequently 9 9 e interior overhead lamp e map lamp For bulb replacement see a dealer or qualified technician AIMING THE HEADLAMPS The headlamp
71. ct the positive booster cable to the positive terminal of the discharged battery Note In the illustrations lightning bolts are used to designate the assisting boosting battery 153 Roadside emergencies 2 Connect the other end of the positive cable to the positive terminal of the assisting battery 3 Connect the negative cable to the negative terminal of the assisting battery 4 Make the final connection of the negative cable to an exposed metal part of the stalled vehicle s engine away from the battery and the carburetor fuel injection system Do not use fuel lines engine rocker covers or the intake manifold as grounding points 154 Roadside emergencies Do not connect the end of the second cable to the negative terminal of the battery to be jumped A spark may cause an explosion of the gases that surround the battery 5 Ensure that the cables are clear of fan blades belts moving parts of both engines or any fuel delivery system parts Jump starting 1 Start the engine of the booster vehicle and run the engine at moderately increased speed 2 Start the engine of the disabled vehicle 3 Once the disabled vehicle has been started run both engines for an additional three minutes before disconnecting the jumper cables Removing the jumper cables Remove the jumper cables in the reverse order that they were connected 1 Remove the jumper cable fr
72. damage to the vehicle or battery Lift the battery with a battery carrier or with your hands on opposite corners Keep batteries out of reach of children Batteries contain sulfuric acid Avoid contact with skin eyes or clothing Shield your eyes when working near the battery to protect against possible splashing of acid solution In case of acid contact with skin or eyes flush immediately with water for a minimum of 15 minutes and get prompt medical attention If acid is swallowed call a physician immediately Because your vehicle s engine is electronically controlled by a computer some control conditions are maintained by power from the battery When the battery is disconnected or a new battery is installed the engine must relearn its idle and fuel trim strategy for optimum driveability and performance To begin this process 1 With the vehicle at a complete stop set the parking brake 2 Put the gearshift in P Park automatic transmission or the neutral position manual transmission turn off all accessories and start the engine 3 Run the engine until it reaches normal operating temperature 4 Allow the engine to idle for at least one minute 5 Turn the A C on and allow the engine to idle for at least one minute 6 Drive the vehicle to complete the relearning process e The vehicle may need to be driven 16 km 10 miles or more to relearn the idle and fuel trim strategy 179 Maintenance and care e If you do n
73. dards for fuel ethanol have been developed to provide FFVs the best possible performance safety and durability To assist alcohol fuel providers in meeting these standards guidelines have also been developed which prescribe Ethanol Fuel Compatible dispensing station equipment These standards and guidelines can be obtained from Ford Motor Company Fuel stations may apply to be certified as meeting these standards However not all stations meet these standards at this time To ensure proper operation of your FFV on fuel ethanol refuel at certified stations If you are experiencing a rough or rolling idle after start up with the outside temperature above 27 C 80 F the idle should improve within 10 to 30 seconds If the problems persist below this temperature see your dealer or a qualified service technician Cleaner air Ford approves the use of reformulated cleaner burning gasolines to improve air quality These gasolines may contain oxygenates up to 10 ethanol or 15 MTBE Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components If you have run out of fuel e You may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine e Your Check Engine indicator may come on For more information on the Check Engine indicator refer to the Instrumentation chapter
74. dealer Similarly in Canada you may purchase additional coverage beyond the basic coverage period by consulting the Ford Roadside Assistance Club brochure or by calling 1 877 294 CLUB 1 877 894 2582 HAZARD FLASHER A Use only in an emergency to warn traffic of vehicle breakdown approaching danger etc The hazard flashers can be operated when the ignition is off e The hazard lights control is located on top of the steering column Depress hazard lights control to activate all hazard flashers simultaneously A e Depress control again to turn the flashers off l RESETTING THE FUEL PUMP SHUT OFF SWITCH The fuel pump shut off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt After a collision if the engine cranks but does not start the fuel pump shut off switch may have been activated The Fuel Reset indicator light will iluminate in the instrument cluster 138 Roadside emergencies The fuel pump shut off switch is located in the passenger s foot well by the kick panel Use the following procedure to reset the fuel pump shut off switch 1 Turn the ignition to the OFF position 2 Check the fuel system for leaks 3 If no fuel leak is apparent reset the fuel pump shut off switch by pushing in on the reset button 4 Turn the ignition to the ON position Pause for a few seconds and return the key to the OFF position 5 M
75. dshield reflection Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the air bag system Cleaning the instrument cluster lens Clean with a damp cloth then dry with a dry cloth Do not use household or glass cleaners as these may damage the lens Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner Remove fresh spots immediately Do not use household or glass cleaners These agents can stain and discolor the fabric Use a mild soap and water solution if necessary Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets Do not bleach or dye the belts because these actions may weaken the belt webbing Check the safety belt system periodically to make sure there are no nicks wear or cuts If your vehicle has been involved in an accident refer to the Safety belt maintenance section in the Seating and safety restraints chapter Underbody Flush the complete underside of vehicle frequently Keep body drain holes unplugged Inspect for road damage 207 Maintenance and care Inside windows Use Ultra Clear Spray Glass Cleaner E4AZ 19C507 AA for the inside windows if they become fogged Cleaning mirrors Do not clean your mirrors with a dry cloth or abrasive materials Use a soft cloth and mild detergent and water Be care
76. e teen deaths occur 4 times more with don t wear often in vehicles with TWO or MORE people belts Children and younger brothers sisters imitate behavior they see I have an air bag Air bags offer greater protection when used with safety belts Frontal airbags are not designed to inflate in rear and side crashes or rollovers Td rather be Not a good idea people who are ejected are 40 thrown clear times more likely to DIE Safety belts help prevent ejection WE CAN T PICK OUR CRASH Do not sit on top of a buckled safety belt to avoid the Belt Minder chime Sitting on the safety belt will increase risk of injury in an accident To disable one time or deactivate the Belt Minder feature please follow the directions stated below 81 Seating and safety restraints One time disable Anytime the safety belt is buckled and then unbuckled during an ignition ON cycle Belt Minder will be disabled for that ignition cycle only Deactivating activating the belt minder feature Read steps 1 9 thoroughly before proceeding with the deactivation activation programming procedure The Belt Minder feature can be deactivated activated by performing the following procedure Before following the procedure make sure that e the parking brake is set e the gearshift is in P Park automatic transmission or the neutral position manual transmission e the ignition switch is in the OFF position all vehicle doors are c
77. e the spare tire carrier lock from the rear access hole located just above the rear bumper and below the tailgate 2 A 3 Insert the straight end of the jack handle into the rear access hole located just above the rear bumper and below the tailgate Forward motion will stop and resistance to turning will be felt when properly engaged 4 Turn the handle counterclockwise until tire is lowered to the ground and the cable is slightly slack 5 Remove the retainer from the spare tire Stowing the spare tire 1 Lay the tire on the ground with the valve stem facing up 2 Install the retainer through the wheel center and slide the wheel under the vehicle 3 Turn the spare handle clockwise until the tire is raised to its original position underneath the vehicle The spare handle ratchets when the tire is raised to the stowed position It will not allow you to overtighten 149 Roadside emergencies 4 If your vehicle is equipped with P265 75 R15 AT tires do not stow a flat or inflated full size spare tire in the spare tire carrier The flat full size tire should be stowed and tied down in the pickup box bed until it can be repaired 5 If removed install the spare tire carrier lock on the access hole above the bumper Tire change procedure To prevent the vehicle from moving when you change a tire be sure the parking brake is set then block in both directions the wheel that is diagonally opposite othe
78. e 229 The Dispute Settlement Board 00 221 Utilizing the Mediation Arbitration Program 224 Daytime running lamps gee LAMPS crier sunsn 18 Dipstick automatic transmission fluid 173 ENGINE OIL zccsaesdeasnecascectacsdegenseass 163 Doors door ajar Warning e 12 lubricant specifications 212 Driveline universal joint and slip yoke ou 177 232 Driving under special conditions 122 123 ia S IEAA SE AATE 122 SONG svszeiexsiseatecesonesssaatecaoinewsvesds 122 STOW AN ICE cisssccisinisarins 123 through water ea s 122 124 Emergencies roadside Jump starting 0 eee 152 Emission control system 195 Engine nooiens 214 215 check engine service engine soon light 8 CLEANING sienen na 204 COOIAIG Aierra neia 168 idle speed control 00008 178 lubrication specifications ce 212 214 refill capacities 0snenns000000 209 service points 160 161 162 starting after a collision 138 Engine block heater 104 Engine oil sirisser 163 checking and adding 163 GID STICK rontana aA 163 filter specifications 165 209 recommendations ccc 165 refill capacities 0 c ees 209 specifications 0 0 212 214 Exhaust fumes ccccccceeeeees 105 Fluid capacities iissa 209 Foglamp S e lt lt sc2snde ecsapeessentiegaassatnese 18 Fo
79. e Maintenance and care chapter If the oil level is correct have your vehicle checked at your dealership or by a qualified technician Battery voltage gauge This shows the battery voltage when the ignition is in the ON position If the pointer moves and stays outside the normal operating range as indicated have the vehicle s electrical system checked as soon as possible H s rr Controls and features HEADLAMP CONTROL Rotate the headlamp control to the ee first position to turn on the parking lamps Rotate to the second position T X to also turn on the headlamps Foglamp control if equipped 0 Turn on the low beam headlamps o and press the foglamp control to eer activate the foglamps The foglamp je control will iluminate when the foglamps are on Press the foglamp control a second time to deactivate the foglamps Daytime running lamps DRL if equipped Turns the headlamps on with a reduced output To activate e the ignition must be in the ON position and e the headlamp control is in the OFF or Parking lamps position A Always remember to turn on your headlamps at dusk or during inclement weather The Daytime Running Light DRL System does not activate your tail lamps and generally may not provide adequate lighting during these conditions Failure to activate your headlamps under these conditions may result in a collision High beams Push forward to activate gt Pull toward you to d
80. e air through the instrument panel registers and the floor ducts Heating and air conditioning capabilities are provided in this mode For added customer comfort when the temperature control knob is anywhere in between the full hot and full cold positions the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers 22 Controls and features e Floor Allows for maximum heating by distributing outside air through the floor ducts However the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode GF Floor and defrost Distributes outside air through the windshield defroster ducts and the floor ducts Heating and air conditioning capabilities are provided in this mode For added customer comfort when the temperature control knob is anywhere in between the full hot and full cold positions the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defrost ducts If the temperature is about 10 C 50 F or higher the air conditioner will automatically dehumidify the air to reduce fogging W Defrost Distributes outside air through the windshield defroster ducts It can be used to clear ice or fog from the windshield If the temperature is about 10 C 50 F or higher the air conditioner will automatically dehumidify the air to reduce fogging Operating tips e In
81. e ambient temperature is above 10 C 50 F However if fluid is added at this time an overfill condition could result when the vehicle reaches normal operating temperature The transmission fluid should be in this range if at normal operating temperature 66 C 77 C 150 F 170 F 174 Maintenance and care The transmission fluid should be in this range if at ambient temperature 10 C 35 C 50 F 95 F High fluid level Fluid levels above the safe range F 7 may result in transmission failure An overfill condition of transmission fluid may cause shift and or engagement concerns and or possible damage High fluid levels can be caused by an overheating condition Adjusting automatic transmission fluid levels Before adding any fluid make sure the correct type is used The type of fluid used is normally indicated on the dipstick and also in the Lubricant specifications section in the Capacities and specifications chapter Use of a non approved automatic transmission fluid may cause internal transmission component damage If necessary add fluid in 250 mL 1 2 pint increments through the filler tube until the level is correct If an overfill occurs excess fluid should be removed by a qualified technician An overfill condition of transmission fluid may cause shift and or engagement concerns and or possible damage 175 Maintenance and care Checking and adding manual transmission fluid
82. e appropriate Motorcraft oil filter or another brand meeting Ford specifications for your engine application 165 Maintenance and care BRAKE FLUID C Checking and adding brake fluid Brake fluid should be checked and refilled as needed Refer to the Scheduled Maintenance Guide for the service interval schedules 1 Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir 2 Visually inspect the fluid level 3 If necessary add brake fluid from a clean un opened container until the level reaches MAX Do not fill above this line 4 Use only a DOT 3 brake fluid certified to meet Ford specifications Refer to Lubricant specifications in the Capacities and specifications chapter Brake fluid is toxic If brake fluid contacts the eyes flush eyes with running water for 15 minutes Seek medical attention if irritation persists If taken internally drink water and induce vomiting Seek medical attention immediately If you use a brake fluid that is not DOT 3 you will cause permanent damage to your brakes Do not let the reservoir for the master cylinder run dry This may cause the brakes to fail 166 Maintenance and care CLUTCH FLUID IF EQUIPPED Check the clutch fluid level Refer to the Scheduled Maintenance Guide for the service interval schedules During normal operation the fluid level in the clutch reservoir should remain constant If the fluid level drops ref
83. e child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion You may wish to discuss the special needs of your child with your pediatrician SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child Carefully follow all of the manufacturer s instructions with the safety seat you put in your vehicle If you do not install and use the safety seat properly the child may be injured in a sudden stop or collision 94 Seating and safety restraints When installing a child safety seat Ford recommends the use of a child safety seat having a top tether strap Install the child safety seat in a seating position which is capable of providing a tether anchorage For more information on top tether straps refer to Attaching safety seats with tether straps and use the safety seat properly the child may be injured in a sudden Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter Use the correct safety belt buckle for that seating position the buckle closest to the direction the tongue is coming from Insert the belt tongue into the proper buckle until you hear a snap and feel it latch Make sure the tongue is securely fastened in the buckle Keep the buckle release button pointing up and away from the safety seat with the t
84. e listed on the Certification Label Make sure that all tires are the same size speed rating and load carrying capacity Use only the tire combinations recommended on the label If you do not follow these precautions your vehicle may not drive properly and safely Make sure that all replacement tires are of the same size type load carrying capacity and tread design e g All Terrain etc as originally offered by Ford 184 Maintenance and care Do not replace your tires with high performance tires or larger size tires Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over Tires that are larger or smaller than your vehicle s original tires may also affect the accuracy of your speedometer SNOW TIRES AND CHAINS Driving too fast for conditions creates the possibility of loss of vehicle control Driving at very high speeds for extended periods of time may result in damage to vehicle components Snow tires must be the same size and grade as the tires you currently have on your vehicle The tires on your vehicle have all weather treads to provide traction in rain and snow However in some climates you may need to use snow tires and chains If you need to use snow tires and chains it is recommended that steel wheels are used of the same size and specifications as those originally installed Follow these guidelines whe
85. e replaced immediately with new ones If a bulb is removed for an extended period of time contaminants may enter the lamp housings and affect lamp performance Replacing headlamp bulbs To remove the headlamp bulb 1 Make sure headlamp switch is in OFF position 2 Open the hood 3 Locate the headlamp bulb through the hole in the upper radiator support assembly 4 Disconnect the electrical connector from the bulb by pulling rearward 197 Maintenance and care 5 Remove the bulb retaining ring by rotating it counterclockwise when viewed from the rear to free it from the bulb socket and slide the ring off the plastic base Keep the ring to retain the new bulb 6 Without turning remove the old bulb by gently pulling it straight back out of the lamp assembly To install the new bulb Handle a halogen headlamp bulb carefully and keep out of children s reach Grasp the bulb only by its plastic base and do not touch the glass The oil from your hand could cause the bulb to break the next time the headlamps are operated 1 With the flat side of the bulb s plastic base facing upward insert the glass end of the bulb into the lamp assembly You may need to turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly When the grooves are aligned push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly 2 Install the bulb r
86. e taking Antabuse or other forms of disulfiram for the treatment of alcoholism Breathing gasoline and or ethanol vapors or skin contact could cause an adverse reaction In sensitive individuals serious personal injury or sickness may result If fuel is splashed on the skin promptly wash skin thoroughly with soap and water Consult a physician immediately if you experience an adverse reaction e FFV fuel tanks may contain zero to 85 percent or more of ethanol Any fuel blends containing gasoline and ethanol should be treated the same as Fuel Ethanol E85 Pure ethanol is the alcohol which is the intoxicating agent in liquor beer and wine It is distilled from the fermentation of plants such as field corn and sugar cane When ethanol is used in the making of motor fuels a small amount of a bad tasting chemical is added to discourage beverage use The resulting fuel is called E 100 meaning 100 pure ethanol diluted by 2 to 5 gasoline as the denaturant Fuel ethanol E4 85 is then made by adding 15 more unleaded gasoline The resulting fuel also has a higher octane rating than unleaded regular gasoline and other properties which allow engine designs with greater efficiency and power Winter blends may contain up to 30 unleaded gasoline 25 plus the denaturant to enhance cold engine starts Severely cold weather may require additional measures for reliable starting Refer to Cold Weather Starting in the Starting chapt
87. eactivate N 18 Controls and features Flash to pass Pull toward you to activate and release to deactivate Use to adjust the brightness of the instrument panel during headlamp and parklamp operation e Rotate up to brighten e Rotate down to dim 5 e Rotate to full up position past 4 DIM detent to turn on interior lamps CLIMATE CONTROL SYSTEM Heater only system if equipped Fan speed control 8 Controls the volume of air circulated se in the vehicle CY O 19 Controls and features Temperature control knob Controls the temperature of the airflow inside the vehicle On Ca heater only systems the air cannot CF be cooled below the outside temperature Mode selector control Controls the direction of the airflow ed on ig to the inside of the vehicle y e 7s Panel Distributes outside air through the instrument panel registers UW e lt A Panel and floor Distributes outside air through the instrument panel registers and the floor ducts e OFF Outside air is shut out and the fan will not operate e A Floor Allows for maximum heating Distributes outside air through the floor ducts e H Floor and defrost Distributes outside air through the floor ducts and the windshield defroster ducts e CHY Defrost Distributes outside air through the windshield defroster ducts It can be used to clear ice or fog from the windshield Operating tips e In hu
88. ed Use only soft cups in the cupholder Hard objects can injure you in a collision CARGO AREA FEATURES Cargo area shade if equipped Your vehicle may be equipped with notches in the side trim panels that are used for a cargo area shade See your dealer for more information REMOTE ENTRY SYSTEM IF EQUIPPED The remote entry system allows you to lock or unlock all vehicle doors without a key The remote entry features only operate with the ignition in the OFF position If there is any potential remote keyless entry problem with your vehicle ensure ALL key fobs remote entry transmitters are brought to the dealership to aid in troubleshooting 63 Controls and features Unlocking the doors Press this control to unlock the driver s door The interior lamps will illuminate Press the control a second time within five seconds to unlock all doors Locking the doors amp Press this control to lock all doors To confirm all doors are closed and locked press the control a second time within five seconds The doors will lock again the horn will chirp and the lamps will flash If any of the doors are ajar the horn will make two quick chirps reminding you to properly close all doors Sounding a panic alarm a Press this control to activate the alarm To deactivate the alarm press the control again or turn the ignition to ACC or ON This device complies with part 15 of the FCC rules and with R
89. ed The vehicle will usually be drivable and will not require towing What you should do if the check engine light illuminates Light turns on solid This means that the OBD II system has detected a malfunction Temporary malfunctions may cause your Check Engine light to illuminate Examples are 1 The vehicle has run out of fuel The engine may misfire or run poorly 2 Poor fuel quality or water in the fuel 3 The fuel cap may not have been properly installed and securely tightened These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and or properly installing and securely tightening the gas cap After three driving cycles without these or any other temporary malfunctions present the Check Engine light should turn off A driving cycle consists of a cold engine startup followed by mixed city highway driving No additional vehicle service is required If the Check Engine light remains on have your vehicle serviced at the first available opportunity Light is blinking Engine misfire is occurring which could damage your catalytic converter You should drive in a moderate fashion avoid heavy acceleration and deceleration and have your vehicle serviced at the first available opportunity Under engine misfire conditions excessive exhaust temperatures could damage the catalytic converter the fuel system interior floor coverings or other vehicle components
90. ehicle has a defect that could cause a crash or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying Ford Motor Company If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer or Ford Motor Company To contact NHTSA you may either call the Auto Safety Hotline toll free at 1 800 424 9393 202 366 0123 in the Washington D C area or write to NHTSA U S Department of Transportation 400 Seventh Street Washington D C 20590 You can also obtain other information about motor vehicle safety from the Hotline 230 Air bag supplemental restraint system s es 84 and child safety seats 85 descriptio sschisssicesassivessssevessesse 84 disposal sssrsrornnononiiienasrai 88 driver air Dag s isscasecssecssecceease 86 indicator light 10 87 ODELALLOM seeren k 86 passenger air bag s es 86 passenger deactivation switch 25 88 Air cleaner filter 0 209 Air conditioning ceee 19 manual heating and air conditioning system s s 21 Ambulance packages 008 3 Antifreeze see Engine coolant 0 168 Anti lock brake system see Brakes cccseeeees 107 108 Anti theft
91. er 187 Maintenance and care Ethanol is more chemically active than gasoline It corrodes some metals and causes some plastic and rubber components to swell break down or become brittle and crack especially when mixed with gasoline Special materials and procedures have been developed for flexible fuel vehicles and the dispensers used by ethanol fuel providers Flexible fuel components and standard unleaded gasoline fuel components are not interchangeable If your vehicle is not serviced in accordance with flexible fuel vehicles procedures damage may occur and your warranty may be invalidated When refueling always shut the engine off and never allow sparks or open flames near the filler neck Never smoke while refueling Fuel vapor is extremely hazardous under certain conditions Care should be taken to avoid inhaling excess fumes The flow of fuel through a fuel pump nozzle can produce static electricity which can cause a fire if fuel is pumped into an ungrounded fuel container Use the following guidelines to avoid static build up when filling an ungrounded fuel container e Place approved fuel container on the ground e DO NOT fill a fuel container while it is in the vehicle e Keep the fuel pump nozzle in contact with the fuel container while filling e DO NOT use a device that would hold the fuel pump handle in the fill position Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1 8 turn on off
92. etaining ring over the plastic base until it contacts the rear of the socket by rotating clockwise until you feel a stop 3 Install the electrical connector into the plastic base until it snaps locking it into position 4 Turn the headlamps on and make sure they work properly If the headlamp was correctly aligned before you changed the bulb you should not need to align it again 198 Maintenance and care Replacing front side marker bulbs 1 Open the hood 2 Remove two screws from the lamp assembly 3 Disengage lamp assembly it has a snap fit 4 Disconnect the electrical connector from the bulb by pulling rearward 5 Rotate bulb socket counterclockwise about 1 4 turn and remove from lamp assembly 6 Carefully pull bulb straight out of socket and push in the new bulb 7 Insert the bulb into the parking lamp assembly When the grooves in the plastic base are aligned push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly and turn to lock 8 Connect the electrical connector into the rear of the plastic base until it snaps 9 Align the lamp studs with the plastic grommets on the vehicle and push to snap in place 10 Install two screws on lamp assembly 199 Maintenance and care Replacing tail lamp turn backup lamp bulbs The tail lamp turn backup lamp bulbs are located in the same portion of the tail lamp assembly one just be
93. etween third and fourth gear occurs Unnecessary shifting of this type could result in reduced fuel economy Warming up a vehicle on cold mornings is not required and may reduce fuel economy Resting your foot on the brake pedal while driving may reduce fuel economy Combine errands and minimize stop and go driving Maintenance Keep tires properly inflated and use only recommended size Operating a vehicle with the wheels out of alignment will reduce fuel economy Use recommended engine oil Refer to Lubricant Specifications Perform all regularly scheduled maintenance items Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle Scheduled Maintenance Guide Conditions Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed Carrying unnecessary weight may reduce fuel economy approximately 0 4 km L 1 mpg is lost for every 180 kg 400 Ib of weight carried Adding certain accessories to your vehicle for example bug deflectors rollbars light bars running boards ski luggage racks may reduce fuel economy 194 Maintenance and care Using fuel blended with alcohol may lower fuel economy e Fuel economy may decrease with lower temperatures during the first 12 16 km 8 10 miles of driving e Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain e Transmissions give their best fuel economy when operated in
94. eutral With the gearshift lever in N Neutral the vehicle can be started P RN D r a and is free to roll Hold the brake are A pedal down while in this position Overdrive The normal driving position for the best fuel economy Transmission P RN P 21 operates in gears one through five Overdrive can be deactivated by pressing the transmission control switch on the end of the gearshift lever 0 D ON OFF 4 The transmission control indicator light TCIL will illuminate on the 0 D instrument cluster O F F Drive Not shown on the display Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the Overdrive position The TCIL will illuminate on the instrument cluster Transmission operates in gears one_through four Drive O D OFF provides more engine braking than Overdrive and is useful whenever driving conditions i e city traffic hilly terrain etc cause the transmission to excessively shift between Overdrive and other gears Deactivate Overdrive when e driving with a heavy load e towing a trailer up or down steep hills e additional engine braking is desired If towing a trailer refer to Driving while you tow in the Trailer Towing chapter 115 Driving To return to Overdrive mode press the transmission control switch The TCIL will no longer be illuminated Each time the
95. flation If the air bag is deployed the air bag will not function again and must be replaced immediately If the air bag is not replaced the unrepaired area will increase the risk of injury in a collision The SRS consists of e driver and passenger air bag modules which include the inflators and air bags e one or more impact and safing sensors passenger air bag deactivation switch and diagnostic monitor RCM e a readiness light and tone e and the electrical wiring which connects the components The RCM restraints control module monitors its own internal circuits and the supplemental air bag electrical system warning including the passenger air bag deactivation switch the impact sensors the system wiring the air bag system readiness light the air bag back up power and the air bag ignitors Determining if the system is operational at The SRS uses readiness lights in the instrument cluster and the passenger air bag deactivate switch or a tone to indicate the condition of the system Refer to the Air bag readiness section in the Instrumentation chapter or Passenger air bag deactivate switch section in this chapter Routine maintenance of the air bag is not required A difficulty with the system is indicated by one or more of the following e The readiness lights will either O O flash or stay lit O e The readiness lights will not Uw illuminate immediately after ignition is turned on e A series of five beeps
96. for Inspection Maintenance I M testing In some localities it may be a legal requirement to pass an I M test of the on board diagnostics system If your Check Engine Service Engine Soon light is on refer to the description in the Warning Lights and Chimes section of the Instrumentation chapter Your vehicle may not pass the I M test with the Check Engine Service Engine Soon light on If the vehicle s powertrain system or its battery has just been serviced the on board diagnostics system is reset to a not ready for I M test condition To ready the on board diagnostics system for I M testing a minimum of 30 minutes of city and highway driving is necessary as described below e First at least 10 minutes of driving on an expressway or highway 196 Maintenance and care e Next at least 20 minutes driving in stop and go city type traffic with at least four idle periods Allow the vehicle to sit for at least eight hours without starting the engine Then start the engine and complete the above driving cycle The engine must warm up to its normal operating temperature Once started do not turn off the engine until the above driving cycle is complete BULBS Replacing exterior bulbs Check the operation of the following lamps frequently e Headlamps e Foglamps e High mount brakelamp e Brakelamps e Turn signals e License plate lamp e Tail lamps e Back up lamps Do not remove lamp bulbs unless they can b
97. ful when removing ice from outside mirrors because you may damage the reflective surface 208 Capacities and specifications MOTORCRAFT PART NUMBERS Component 2 5L 14 engine 3 0L FFV V6 4 0L V6 engine engine Oil filter FL 4005S FL 400S FL 1A PCV valve EV 227 EV 130 EV 225 Spark plugs AWSF 32F AGSF 22PP AGSF 22PP Refer to Vehicle Emissions Control Information VECI decal for spark plug gap information Air filter FA 1658 FA 1658 FA 1658 acne a a Two spark plugs per cylinder required eight total Tf any spark plug needs to be removed for inspection it must be re installed in the same cylinder Cylinders No 1 2 and 3 have a PG suffix Cylinders No 4 5 and 6 have a P suffix If any spark plug needs to be replaced use only spark plugs with the service part number suffix letters PP as shown on the engine decal REFILL CAPACITIES Fluid Ford Part Application Capacity Name Engine oil Motorcraft SAE 2 5L I4 and 3 0L V6 4 3L includes 5W 30 Super engine 4 5 quarts filter change Premium Motor 40L v6 engine 4 7L Oil 5 0 quarts All Fill to line on Brake fluid High Performance reservoir DOT 3 Motor Vehicle Brake Fluid Power Motorcraft All Fill to range on steering fluid MERCON ATF dipstick 209 Capacities and specifications Fluid Ford Part Application Capacity Name Transmission Motorcraft 5 speed manual 2 65L fluid t MERCON ATF 2 8 quarts
98. gh all available gears Deactivating overdrive Press the Transmission Control Switch TCS located on the end of the gearshift lever The Transmission Control Indicator Light TCIL will illuminate on the instrument cluster The transmission will operate in all gears except overdrive To return to normal overdrive mode press the Transmission Control Switch again The TCIL will no longer be illuminated 0 D ON OFF 0 D 4 Controls and features When you shut off and re start your vehicle the transmission will automatically return to normal Overdrive mode For additional information about the gearshift lever and the transmission control switch operation refer to the Automatic Transmission Operation section of the Driving chapter TILT STEERING WHEEL IF EQUIPPED Pull the tilt steering control toward you to move the steering wheel up or down Hold the control while adjusting the wheel to the desired position then release the control to lock the steering wheel in position A Never adjust the steering wheel when the vehicle is moving HAZARD FLASHER For information on the hazard flasher control refer to Hazard flasher in the Roadside emergencies chapter 60 Controls and features WINDSHIELD WIPER WASHER CONTROLS SJ Rotate the windshield wiper control to the desired interval low or high speed position The bars of varying length are for intermittent wipers When in this
99. go nets Cargo organizers Cargo shades Super Cab only Engine block heaters Manual sliding rear window Tire step Travel equipment Daytime running lights Fog lights Heavy duty battery Pickup box rails Removable luggage rack Running boards Speed control Trailer hitch Trailer hitch bars and balls Trailer hitch wiring adaptor Protection and appearance equipment Air bag anti theft locks Bed mat bedliner tailgate covers Bed mats Bedliners Carpet floor mats Cleaners waxes and polishes Front end covers full and sport 227 Customer assistance Hood deflectors Locking gas cap Lubricants and oils Molded vinyl floor mats Side window air deflectors Spare tire lock Step bumpers Step sill plates Tailgate protector Tonneau covers Touch up paint Universal floor mats For maximum vehicle performance keep the following information in mind when adding accessories or equipment to your vehicle When adding accessories equipment passengers and luggage to your vehicle do not exceed the total weight capacity of the vehicle or of the front or rear axle GVWR or GAWR as indicated on the Safety compliance certification label Consult your dealer for specific weight information The Federal Communications Commission FCC and Canadian Radio Telecommunications Commission CRTC regulate the use of mobile communications systems such as two way radios telephones and theft alarms that are equipped with
100. h is in the OFF position and the ignition switch is in ON have the passenger air bag switch serviced at your Ford or Lincoln Mercury dealer immediately In order to avoid inadvertent activation of the switch always remove the ignition key from the passenger air bag ON OFF switch Turning the passenger air bag back on The passenger air bag remains OFF until you turn it back ON 1 Insert the ignition key and turn the switch to ON 2 The OFF light will briefly illuminate when the ignition is turned to ON This indicates that the passenger air bag is operational PASSENGER AIRBAG If the light is illuminated when the passenger air bag ON OFF switch is in the ON position and the ignition switch is in ON have the passenger air bag ON OFF switch serviced at your Ford or Lincoln Mercury dealer immediately The passenger side air bag should always be ON the air bag OFF light should not be illuminated unless the passenger is a person who meets the requirements stated either in Category 1 2 or 3 of the NHTSA Transport Canada deactivation criteria which follows 89 Seating and safety restraints The safety belts for the driver and right front passenger seating positions have been specifically designed to function together with the air bags in certain types of crashes When you turn OFF your air bag you not only lose the protection of the air bag you also may reduce the effectiveness of your safety belt system which was
101. hangeable DO NOT mix MERCON and MERCON V Refer to your Scheduled Maintenance Guide to determine the correct service interval 213 Capacities and specifications ENGINE DATA Engine 2 5L I4 engine SOL BEY YS 4 0L V6 engine engine Ethanol E 85 Spark plug gap 1 07 1 17 mm 1 07 1 17 mm 1 3 1 4 mm 0 042 046 0 042 046 0 052 0 056 inch inch inch EDIS EDIS EDIS Compression 9 4 1 9 14 1 9 0 1 ratio 2 3L I4 2 5L I4 3 0L V6 4 0L V6 engine engine engine engine fuel 1 3 4 2 1 3 4 2 1 4 2 5 3 6 1 4 2 5 3 6 1 04 1 19mm 1 07 1 17mm 1 07 1 17mm 1 3 1 4 mm 0 041 0 047 0 042 0 046 0 042 0 046 0 052 0 056 i plug system Compression 9 7 1 A 9 14 1 O ratio 214 Capacities and specifications VEHICLE DIMENSIONS Vehicle Regular Cab Regular Cab Supercab mm dimensions Short Wheel Long Wheel Cin Base SWB mm Base LWB Cin mm in 1 Overall 4 763 187 5 5 093 200 5 5 153 202 9 ee ee ee eee 2 Overall 1 785 70 3 1 785 70 3 1 785 70 3 ee Pee Pee eee 3 Overall 1 575 62 0 1 586 62 4 1585 62 4 5 Track 1 486 58 5 1 486 58 5 1 485 58 5 Front 5 Track 1 455 57 3 1 455 57 3 1 455 57 3 Rear 215 nd specifications ities a Capac Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration
102. he vehicle is on level ground 2 Turn the engine off and wait a few minutes for the oil to drain into the oil pan 3 Set the parking brake and ensure the gearshift is securely latched in P Park automatic transmissions or 1 First manual transmissions 4 Open the hood Protect yourself from engine heat 5 Locate and carefully remove the engine oil level indicator dipstick ADD 10T gt RRR RRR RRR FULL WOOO SSN lt MIN REAR RRR RARER max __ 6 Wipe the indicator clean Insert the indicator fully then remove it again e If the oil level is between the ADD and FULL marks or between the MIN and MAX marks depending on application the oil level is acceptable DO NOT ADD OIL 163 Maintenance and care If the oil level is below the ADD mark or MIN mark add enough oil to raise the level within the ADD FULL range or MIN MAX range Oil levels above the letter F in FULL or the MAX mark may cause engine damage Some oil must be removed from the engine by a service technician 7 Put the indicator back in and ensure it is fully seated Adding engine oil 1 Check the engine oil For instructions refer to Checking the engine owl in this chapter 2 If the engine oil level is not within the normal range add only certified engine oil of the recommended viscosity Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening 3 Recheck the engine oil
103. humid weather select Y before driving This will reduce fogging on your windshield After a few minutes select any desired position To prevent humidity buildup inside the vehicle do not drive with the climate control system in the OFF or MAX A C position e Do not put objects under the front seat that will interfere with the airflow to the rear seats if equipped e Remove any snow ice or leaves from the air intake area at the bottom of the windshield under the hood If your vehicle has been parked with the windows closed during hot weather the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open This will force most of the hot stale air out of the vehicle Then operate your air conditioner as you would normally 23 Controls and features e Do not place objects over the defroster outlets These objects can block airflow and reduce your ability to see through your windshield Also avoid placing small objects on top of your instrument panel These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop 4WD CONTROL IF EQUIPPED This control operates the 4WD i Refer to the Driving chapter for ap HGH cow more information e 24 Controls and features AUXILIARY POWER
104. ic car wash because of the vehicle s reduced ground clearance e try to repair the temporary spare tire or remove it from its wheel e use the wheel for any other type of vehicle Conventional spare tire information If you have the conventional spare tire you can use it as a spare or a regular tire The spare is identical to the other tires on your vehicle although the wheel may not match 147 Roadside emergencies Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations Tool Spare tire Under the vehicle just forward of the rear bumper Jack jack handle Regular Cab behind seats and underneath the wheel nut wrench jack and tools cover SuperCab stowed in the passenger side rear cab compartment or behind the jump seat in a separate tool bag Four door models stowed behind the front seats between jump seats and underneath jack and tools cover Key spare tire lock if In the glove box equipped Removing the spare tire 1 Assemble the jack handle to the lug wrench as shown in the illustrations When connecting the jack handle assemble the following e one handle extension and one y typical extension To assemble slide parts together To gt disconnect depress button and pull apart e one wheel nut wrench Depress D button and slide together yD _ 148 Roadside emergencies 2 If equipped unlock and remov
105. ies quickly e Press gt to move to the next frequency up the band whether or not a listenable station is located there Hold for quick movement Seek function The seek function control works in radio mode Seek function in radio mode e Press A to find the next listenable station down the frequency band e Press to find the next listenable station up the frequency band Scan function The scan function works in radio mode Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band Press the SCAN control again to stop the scan mode Radio station memory preset The radio is equipped with six station memory preset controls These controls can be used to select up to six preset AM stations and twelve FM stations six in FM1 and six in FM2 32 Controls and features Setting memory preset siations 1 Select the frequency band with the AM or the FM select control 2 Select a station Refer to Tune adjust or Seek function for more information on selecting a station 3 Press and hold a memory preset control until the sound returns indicating the station is held in memory on the control you selected VOOM Bass adjust The bass adjust control allows you i to increase or decrease the audio A system s bass output BASS ae Treble adjust The treble adjust control allows you to increase or decrease the audio A
106. ildren or Safety Seats for Children later in this chapter How to use the automatic locking mode e Buckle the combination lap and shoulder belt e Grasp the shoulder portion and pull downward until the entire belt is extracted e Allow the belt to retract As the belt retracts you will hear a clicking sound This indicates the safety belt is now in the automatic locking mode 75 Seating and safety restraints How to disengage the automatic locking mode Disconnect the combination lap shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive emergency locking mode After any vehicle collision the seat belt system at all outboard seating positions except driver which has no automatic locking retractor feature must be checked by a qualified technician to verify that the automatic locking retractor feature for child seats is still functioning properly In addition all seat belts should be checked for proper function BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly automatic locking retractor feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions Front safety belt height adjustment Your vehicle has safety belt height adjustments for the d
107. ill the fluid level to the step in the reservoir Use only a DOT 3 brake fluid designed to meet Ford specifications Refer to Capacities and specifications Brake fluid is toxic If brake fluid contacts the eyes flush eyes with running water for 15 minutes Seek medical if irritation persists If taken internally drink water and induce vomiting Seek medical attention immediately 1 Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir 2 Remove cap and rubber diaphragm from reservoir 3 Add fluid until the level reaches the step in the reservoir 4 Reinstall rubber diaphragm and cap onto reservoir 167 Maintenance and care WINDSHIELD WASHER FLUID lt 1 Checking and adding washer fluid Check the washer fluid whenever you stop for fuel The reservoir is highlighted with a symbol If the level is low add enough fluid to fill the reservoir In very cold weather do not fill the reservoir all the way Only use a washer fluid that meets Ford specifications Refer to Lubricant specifications in the Capacities and specifications chapter State or local regulations on volatile organic compounds may restrict the use of methanol a common windshield washer antifreeze additive Washer fluids containing non methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle s paint finish wiper blades or washer system
108. inflate in a collision does not mean that something is wrong with the system Rather it means the forces were not of the type sufficient to cause activation Air bags are designed to inflate in frontal and near frontal collisions not rollover side impact or rear impacts The air bags inflate and deflate rapidly upon activation After air bag deployment it is normal to notice a smoke like powdery residue or smell the burnt propellant This may consist of cornstarch talcum powder to lubricate the bag or sodium compounds e g baking soda that result from the combustion process that inflates the air bag Small amounts of sodium hydroxide may be present which may irritate the skin and eyes but none of the residue is toxic While the system is designed to help reduce serious injuries it may also cause minor abrasions swelling or temporary hearing loss Because air bags must inflate rapidly and with considerable force there is the risk of death or serious injuries such as fractures facial and eye injuries or internal injuries particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment Thus it is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control 86 Seating and safety restraints Several air bag system components get hot after inflation Do not touch them after in
109. inserting a finger or pencil into the hole and turning the hub e Remove loose labels before inserting tapes 52 Controls and features e Do not leave tapes in the cassette player for a long time when not being played Radio frequency information The Federal Communications Commission FCC and the Canadian Radio and Telecommunications Commission CRTC establish the frequencies AM and FM stations may use for their broadcasts Allowable frequencies are AM 580 540 1600 1610 kHz FM 87 7 87 9 107 7 107 9 MHz Not all frequencies are used in a given area Radio reception factors Three factors can affect radio reception e Distance strength The further an FM signal travels the weaker it is The listenable range of the average FM station is approximately 40 km 24 miles This range can be affected by signal modulation Signal modulation is a process radio stations use to increase their strength volume relative to other stations e Terrain Hills mountains and tall buildings between your vehicle s antenna and the radio station signal can cause FM reception problems Static can be caused on AM stations by power lines electric fences traffic lights and thunderstorms Moving away from an interfering structure out of its shadow returns your reception to normal e Station overload Weak signals are sometimes captured by stronger signals when you pass a broadcast tower A stronger signal may temporarily overtake a
110. iod at high speeds in city traffic during hot weather or pulling a trailer the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking 1 Drive the vehicle 30 km 20 miles or until it reaches normal operating temperature 2 Park the vehicle on a level surface and engage the parking brake 3 With the parking brake engaged and your foot on the brake pedal start the engine and move the gearshift lever through all of the gear ranges Allow sufficient time for each gear to engage 4 Latch the gearshift lever in P Park and leave the engine running 5 Remove the dipstick wiping it clean with a clean dry lint free rag If necessary refer to Identifying components in the engine compartment in this chapter for the location of the dipstick 6 Install the dipstick making sure it is fully seated in the filler tube 7 Remove the dipstick and inspect the fluid level The fluid should be in the designated area for normal operating temperature or ambient temperature Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick t and the ambient temperature is above 10 C 50 F Correct fluid level The transmission fluid should be checked at normal operating temperature 66 C 77 C 150 F 170 F on a level surface The normal operating temperature can be reached after approximately 30 km 20 miles of driving You can check the fluid without driving if th
111. irst try turn the key to OFF wait 10 seconds and try again N 102 Starting 3 If the temperature is below 12 C 10 F and the engine does not start in 15 seconds on the first try turn the key OFF and wait 10 seconds and try again If the engine does not start in two attempts press the accelerator pedal all the way to floor and hold Turn the key to START position 4 When the engine starts release the key then release the accelerator pedal gradually as the engine speeds up 5 After idling for a few seconds apply the brake and release the parking brake Cold weather starting flexible fuel vehicles only As the outside temperature approaches freezing ethanol fuel distributors should supply winter grade EH 85 ethanol same as with unleaded gasoline If summer grade Ea 85 ethanol is used in cold weather conditions you may experience increased cranking times rough idle or hesitation until the engine has warmed up Consult your fuel distributor for the availability of winter grade EK 85 ethanol High quality blends of winter grade Eq 85 ethanol will produce satisfactory cold weather starting and driving results However fuel composition varies and sub optimal winter grade blends could produce increased cranking times rough idle or hesitation at temperatures below 18 degrees C 0 degrees F If you experience this condition you may find that a different brand of winter grade E4 85 Cf available in
112. ition switch illuminates1l 2 minutes and the is turned to the ON position warning chime sounds 4 8 seconds The driver s safety belt is buckled The safety belt warning light and while the indicator light is warning chime turn off illuminated and the warning chime is sounding The driver s safety belt is buckled The safety belt warning light and before the ignition switch is turned indicator chime remain off to the ON position 79 Seating and safety restraints Belt minder if equipped The Belt Minder feature is a supplemental warning to the safety belt warning function This feature provides additional reminders to the driver that the driver s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster The driver s safety belt is not The Belt Minder feature is buckled before the vehicle has activated the safety belt warning reached at least 5 km h 8 mph light illuminates and the warning and 1 2 minutes have elapsed chime sounds for 6 seconds every since the ignition switch has been 30 seconds repeating for turned to ON approximately 5 minutes or until safety belt is buckled The driver s safety belt is buckled The Belt Minder feature will not while the safety belt indicator light activate is illuminated and the safety belt warning chime is sounding The driver s safety belt is buckled The Belt Minder feature
113. itions of their use however and may depart significantly from the norm due to variations in driving habits service practices and differences in road characteristics and climate Traction AAA BC The traction grades from highest to lowest are AA A B and C Those grades represent the tire s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance The traction grade assigned to this tire is based on straight ahead braking traction tests and does not include acceleration cornering hydroplaning or peak traction characteristics Temperature A B C The temperature grades are A the highest B and C representing the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sustained high temperature can cause the material of the tire to degenerate and reduce tire life and excessive temperature can lead to sudden tire failure The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No 109 Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law The temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive
114. king on steep downgrades Upshifts can be made fe a ae awe by shifting to 2 Second or to Overdrive Selecting 1 Low at higher speeds causes the transmission to shift to a lower gear and will shift to 1 Low after vehicle decelerates to the proper speed Forced Downshifits To gain acceleration in Overdrive or Drive O D OFF when passing another vehicle push the accelerator to the floor The transmission will downshift to the appropriate gear third second or first gear Driving with a 5 speed automatic transmission if equipped Understanding gearshift positions Hold the brake pedal down while you move the gearshift lever from P Park to another position If you do not hold the brake pedal down your vehicle may move unexpectedly and injure someone P Park To put your vehicle in gear start the engine depress the brake pedal then move gearshift lever out of P Park Always come to a complete stop before shifting into P Park Make sure the gearshift lever is securely latched in P Park This position locks the transmission and prevents the rear wheels from turning Always set the parking brake fully and make sure the gearshift is latched in P Park Turn off the ignition whenever you leave your vehicle 114 Driving R Reverse With the gearshift lever in R Reverse the vehicle will move backward Always come to a complete stop before shifting into and out of R Reverse N N
115. kly Use of an engine block heater is strongly recommended if you live in a region where temperatures reach 23 C 10 F or below Your engine block heater also comes with a battery warmer The battery warmer wraps around the battery and keeps the battery warm when the engine block heater is plugged in For best results plug the heater in at least three hours before starting the vehicle Using the heater for longer than three hours will not harm the engine so the heater can be plugged in the night before starting the vehicle To prevent electrical shock do not use your heater with ungrounded electrical systems or two pronged cheater adapters 104 Starting Guarding against exhaust fumes Although odorless and colorless carbon monoxide is present in exhaust fumes Take precautions to avoid its dangerous effects If you ever smell exhaust fumes of any kind inside your vehicle have your dealer inspect and fix your vehicle immediately Do not drive if you smell exhaust fumes These fumes are harmful and could kill you Have the exhaust and body ventilation systems checked whenever e the vehicle is raised for service e the sound of the exhaust system changes e the vehicle has been damaged in a collision Engine exhaust some of its constituents and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Important ventilating infor
116. l only function if the outside temperature is about 10 C 50 F or higher Since the air conditioner removes considerable moisture from the air during operation it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle Under normal conditions your vehicle s climate control system should be left in any position other than MAX A C or OFF when the vehicle is parked This allows the vehicle to breathe through the outside air inlet duct In snowy or dirty conditions leave the mode selector in the OFF position e MAX A C Uses recirculated air to cool the vehicle MAX A C is noisier than A C but more economical and will cool the inside of the vehicle faster Airflow will be from the instrument panel registers This mode can also be used to prevent undesirable odors from entering the vehicle e A C Uses outside air to cool the vehicle It is quieter than MAX A C but not as economical Airflow will be from the instrument panel registers e re Panel Distributes outside air through the instrument panel registers However the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode e OFF Outside air is shut out and the fan will not operate For short periods of time only use this mode to prevent undesirable odors from entering the vehicle e lt A Panel and floor Distributes outsid
117. lane Drive Fairlane Business Park 3 Allen Park Michigan 48101 U S A Telephone 313 594 4857 FAX 313 390 0804 If you are in another foreign country contact the nearest Ford dealership If the dealership employees cannot help you they can direct you to the nearest Ford affiliate office If you buy your vehicle in North America and then relocate outside of the U S or Canada register your vehicle identification number VIN and new address with Ford Motor Company Worldwide Direct Market Operations FORD CAR CARE PRODUCTS FOR YOUR VEHICLE Ford has many quality products available from your dealer to clean your vehicle and protect its finishes These quality products have been specifically engineered to fulfill your automotive needs they are custom designed to complement the style and appearance of your vehicle Each product is made from high quality materials and that meet or exceed Ford s rigid specifications For best results use the following or products of equivalent quality Ford Custom Clearcoat Polish Ford Custom Silicone Gloss Polish Ford Custom Vinyl Protectant not available in Canada Motorcraft Vinyl Conditioner Canada only 225 Customer assistance Ford Deluxe Leather and Vinyl Cleaner not available in Canada Motorcraft Vinyl Cleaner Canada only Ford Extra Strength Tar and Road Oil Remover not available in Canada Ford Extra Strength Upholstery Cleaner Canada only Ford Extra Strength
118. leave your vehicle 111 Driving If the parking brake is fully released but the brake warning lamp remains illuminated the brakes may not be working properly See your dealer or a qualified service technician Driving with a 4 speed automatic transmission if equipped To put your vehicle in gear start the engine depress the brake pedal then move gearshift lever out of P Park Hold the brake pedal down while you move the gearshift lever from P Park to another position If you do not hold the brake pedal down your vehicle may move unexpectedly and injure someone Understanding gearshift positions P Park Always come to a complete stop before shifting into P Park Make P RN D 21 sure the gearshift lever is securely POSS latched in P Park This position locks the transmission and prevents the rear wheels from turning Always set the parking brake fully and make sure the gearshift lever is latched in P Park Turn off the ignition whenever you leave your vehicle R Reverse With the gearshift in R Reverse the vehicle will move backward P R N D 2 1 aas a O before shifting into and out of R Reverse N Neutral With the gearshift in N Neutral the vehicle can be started and is P RN D r A free to roll Hold the brake pedal D down while in this gear 112 Driving Overdrive The normal driving position for the best fuel economy Transmission P RN P 2 1
119. lication speak to your dealer or write call to the Board at the following address phone number Dispute Settlement Board P O Box 5120 Southfield MI 48086 5120 1 800 428 3718 223 Customer assistance You may also contact the North American Customer Assistance Center at 1 800 392 3673 Ford TDD for the hearing impaired 1 800 232 5952 or by writing to the Center at the following address Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P O Box 6248 Dearborn Michigan 48121 UTILIZING THE MEDIATION ARBITRATION PROGRAM CANADA ONLY In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory related vehicle service concern have been unsatisfactory Ford of Canada participates in an impartial third party mediation arbitration program administered by the Canadian Motor Vehicle Arbitration Plan CAMVAP The CAMVAP program is a straight forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings In the CAMVAP program impartial third party arbitrators conduct hearings at mutually convenient times and places in an informal environment These impartial arbitrators review the positions of the parties make decisions and when appropriate render awards to resolve disputes CAMVA
120. lity with manual transfer cases and automatic transmissions follow these guidelines for recreational towing e Release the parking brake e Turn the key in the ignition to the OFF UNLOCKED position e Place the transmission in N Neutral e Do not exceed a distance of 80 km 50 miles e Do not exceed 56 km h 85 mph vehicle speed If a distance of 80 km 50 miles or a speed of 56 km h 85 mph must be exceeded you must disconnect the driveshaft Ford recommends the driveshaft be removed installed only by a qualified technician See your local dealer for driveshaft removal installation Improper removal installation of the driveshaft can cause transmission fluid loss damage to the driveshaft and internal transmission components CAMPER BODIES Your Ranger Pickup is not recommended for slide in camper bodies 136 Roadside emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern Ford offers a complimentary roadside assistance program This program is separate from the New Vehicle Limited Warranty The service is available e 24 hours seven days a week e for the Basic warranty period Canada or New Vehicle Limited Warranty period U S of three years or 60 000 km 86 000 miles whichever comes first on Ford and Mercury vehicles and four years or 80 000 km 50 000 miles on Lincoln vehicles Roadside assistance will cover e changing a flat tire e jump starts e lock out assis
121. locking retractor feature for child seats is still functioning properly In addition all seat belts should be checked for proper function BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly automatic locking retractor feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement For example if the driver brakes suddenly or turns a corner sharply or the vehicle receives an impact of approximately 8 km h 5 mph or more the combination safety belts will lock to help reduce forward movement of the driver and passengers Automatic locking mode In this mode the shoulder belt is automatically pre locked The belt will still retract to remove any slack in the shoulder belt The automatic locking mode is not available on the driver safety belt 74 Seating and safety restraints When to use the automatic locking mode e Anytime a child safety seat is installed in a passenger front or outboard rear seating position Gif equipped Children 12 years old and under should be properly restrained in the rear seat whenever possible Refer to Safety Restraints for Ch
122. losed the driver s safety belt is unbuckled e the parklamps headlamps are in OFF position If vehicle is equipped with Autolamps this will not affect the procedure To reduce the risk of injury do not deactivate activate the Belt Minder feature while driving the vehicle 1 Turn the ignition switch to the RUN or ON position DO NOT START THE ENGINE 2 Wait until the safety belt warning light turns off Approximately 1 2 minutes e Steps 3 5 must be completed within 60 seconds or the procedure will have to be repeated 3 Buckle then unbuckle the safety belt three times ending with the safety belt unbuckled This can be done before or during Belt Minder warning activation 4 Turn on the parklamps headlamps turn off the parklamps headlamps 5 Buckle then unbuckle the safety belt three times ending with the safety belt unbuckled e After step 5 the safety belt warning light will be turned on for three seconds 82 Seating and safety restraints 6 Within seven seconds of the safety belt warning light turning off buckle then unbuckle the safety belt e This will disable Belt Minder if it is currently enabled or enable Belt Minder if it is currently disabled 7 Confirmation of disabling Belt Minder is provided by flashing the safety belt warning light four times per second for three seconds 8 Confirmation of enabling Belt Minder is provided by flashing the safety belt warning light four times per second f
123. low the other Follow the same steps to replace either bulb 1 Open the liftgate to expose the lamp assemblies 2 Remove the four screws and the lamp assembly from vehicle 3 Rotate bulb socket counterclockwise turn and remove from lamp assembly 4 Carefully pull the bulb straight out of the socket and push in the new bulb 5 Install the bulb socket in lamp assembly by turning clockwise 6 Install the lamp assembly and secure with four screws Replacing foglamp bulbs 1 Remove the bulb socket from the foglamp by turning counterclockwise 2 Disconnect the electrical connector from the foglamp bulb 3 Connect the electrical connector to the new foglamp bulb 4 Install the bulb socket in the foglamp turning clockwise 200 Maintenance and care Replacing high mount brakelamp and cargo lamp bulbs The replacement of the high mount brakelamp bulb and cargo lamp bulb is basically the same This procedure covers the high mount brakelamp bulb To remove the brakelamp assembly 1 Remove the two screws and lamp assembly from vehicle 2 Remove the bulb socket from lamp assembly by rotating it counterclockwise 3 Carefully pull bulb straight out of socket and push in the new bulb To install the brakelamp assembly 1 Install the bulb socket into the lamp assembly by rotating clockwise 2 Install the lamp assembly on the vehicle and secure with two s
124. lume knob to adjust the desired level Treble adjust The treble adjust control allows you to increase or decrease the audio system s treble output Press the TONE control twice then use the volume knob to adjust the desired level VOL PUSH ON 28 Controls and features Speaker balance adjust Speaker sound distribution can be VOL adjusted between the right and left let speakers TONE Press the TONE control three times then use the volume knob to adjust the desired level Speaker fade adjust if equipped Speaker sound can be adjusted VOL between the front and rear ee speakers Press the TONE control four times then use the volume knob to adjust the desired level Setting the clock Press CLK to toggle between listening frequencies and clock mode To set the hour press and hold the CLK control until CLOCK SET appears in the display and press the SEEK control lt to decrease hours and gt to increase hours l l P ZEA Controls and features To set the minute press and hold the CLK control until CLOCK SET appears in the display and press the TUNE control e A to decrease minutes and gt to increase minutes The CLK control will allow you to switch between media display mode radio station stereo information etc and clock display mode time When in clock mode the media information will display for ten seconds when the radio is tur
125. mation Indicates that this Owner Guide contains information on this subject Please refer to the Index to locate Lil the appropriate section which will provide you more information WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others your vehicle and its equipment BREAKING IN YOUR VEHICLE There are no particular breaking in rules for your vehicle During the first 1 600 km 1 000 miles of driving vary speeds frequently This is necessary to give the moving parts a chance to break in 2 Introduction INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing Ford may change the contents without notice and without incurring obligation SPECIAL NOTICES Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles Before you drive your vehicle please read this Owner s Guide carefully Your vehicle is not a passenger car As with other vehicles of this type failure to operate this vehicle correctly may result in loss of control or an accident Be sure to read Driving off road in the Driving chapter as well as the Four Wheeling supplement included with 4WD and utility type vehicles Using your vehicle as a snowplow AN Do not use this vehicle for snowplowing Using your vehicle as an ambulance A Do not u
126. mation If the engine is idling while the vehicle is stopped in an open area for long periods of time open the windows at least 2 5 cm one inch Adjust the heating or air conditioning Gif equipped to bring in fresh air Improve vehicle ventilation by keeping all air inlet vents clear of snow leaves and other debris 105 Driving BRAKES Your service brakes are self adjusting Refer to the scheduled maintenance guide for scheduled maintenance Occasional brake noise is normal and often does not indicate a performance concern with the vehicle s brake system In normal operation automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied Such noises are usually heard during the first few brake applications in the morning however they may be heard at any time while braking and can be aggravated by environmental conditions such as cold heat moisture road dust salt or mud If a metal to metal continuous grinding or continuous squeal sound is present while braking the brake linings may be worn out and should be inspected by a qualified service technician Rear anti lock brake system RABS Rear Anti lock Brake System RABS is standard equipment on this vehicle RABS is designed to help you maintain directional stability in emergency stopping situations With RABS the rear brakes are kept from locking during panic stops however the front wheels can
127. meters traveled Divide total miles traveled by total gallons used Keep a record for at least one month and record the type of driving city or highway This will provide an accurate estimate of the vehicle s fuel economy under current driving conditions Additionally keeping records during summer and winter will show how temperature impacts fuel economy In general lower temperatures give lower fuel economy Ethanol has less energy per gallon than gasoline Fuel economy will decrease as the percentage of ethanol used is increased Driving style good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy Habits e Smooth moderate operation can yield up to 10 savings in fuel e Steady speeds without stopping will usually give the best fuel economy 193 Maintenance and care Idling for long periods of time greater than one minute may waste fuel Anticipate stopping slowing down may eliminate the need to stop Sudden or hard accelerations may reduce fuel economy Slow down gradually Driving at reasonable speeds traveling at 88 km h 55 mph uses 15 less fuel than traveling at 105 km h 65 mph Revving the engine before turning it off may reduce fuel economy Using the air conditioner or defroster may reduce fuel economy You may want to turn off the speed control in hilly terrain if unnecessary shifting b
128. mid weather select Y before driving This will reduce fogging on your windshield After a few minutes select any desired position e To reduce humidity buildup inside the vehicle don t drive with the climate control system in the OFF position e Don t put objects under the front seat that will interfere with the airflow to the rear seats if equipped 20 Controls and features e Remove any snow ice or leaves from the air intake area at the bottom of the windshield under the hood e Do not place objects over the defroster outlets These objects can block airflow and reduce your ability to see through your windshield Also avoid placing small objects on top of your instrument panel These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop Manual heating and air conditioning system if equipped O Gs Fan speed control Controls the volume of air circulated in the vehicle Ns lt 7 Temperature control knob Controls the temperature of the airflow inside the vehicle O 21 Controls and features Mode selector control Controls the direction of the airflow IEA to the inside of the vehicle The air conditioning compressor will operate in all modes except and yl However the air conditioning wil
129. n using snow tires and chains e Do not use tire chains on aluminum wheels Chains may chip the wheels e Use only SAE Class S chains e Install chains securely verifying that the chains do not touch any wiring brake lines or fuel lines e Drive cautiously If you hear the chains rub or bang against your vehicle stop and re tighten the chains If this does not work remove the chains to prevent damage to your vehicle e If possible avoid fully loading your vehicle e Remove the tire chains when they are no longer needed Do not use tire chains on dry roads 185 Maintenance and care e The suspension insulation and bumpers will help prevent vehicle damage Do not remove these components from your vehicle when using snow tires and chains WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS f Important safety precautions Do not overfill the fuel tank The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire The fuel system may be under pressure If the fuel filler cap is venting vapor or if you hear a hissing sound wait until it stops before completely removing the fuel filler cap Otherwise fuel may spray out and injure you or others If you do not use the proper fuel filler cap excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel system to work improperly in a collision which may result in possible personal injury Automotive fuels can cause serious i
130. nder the trailer tongue and allow slack for turning corners If you use a rental trailer follow the instructions that the rental agency gives to you Do not attach safety chains to the bumper Trailer brakes Electric brakes and manual automatic or surge type trailer brakes are safe if installed properly and adjusted to the manufacturer s specifications The trailer brakes must meet local and Federal regulations 132 Driving Do not connect a trailer s hydraulic brake system directly to your vehicle s brake system Your vehicle may not have enough braking power and your chances of having a collision greatly increase The braking system of the tow vehicle is rated for operation at the GVWR not GCWR Trailer lamps Trailer lamps are required on most towed vehicles Make sure your trailer lamps conform to local and Federal regulations See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps Using a step bumper The optional step bumper is equipped with an integral hitch and requires only a ball with a 19 mm 8 4 inch shank diameter The bumper has a 907 kg 2 000 Ib trailer weight and 91 kg 200 lb tongue weight capability The rated capcities as shown in this guide for trailer towing with the factory bumper are only valid when the trailer hitch ball is installed directly into the ball hole in the bumper Addition of bracketry to either lower the ball hitch positi
131. ned on and then revert to clock information Anytime that the media is changed new radio station etc the media information will again display for ten seconds before reverting back to the clock In media mode the media information will always be displayed AM FM stereo cassette VOL PUSH ON OGE ee ee EAE TE eD lt TUNE gt ee ee OOO OOQ 30 Controls and features Volume power control Press the control to turn the audio VOL PUSH ON system on or off O Turn the control to raise or lower volume x K VOL PUSH ON If the volume is set above a certain level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition switch is turned back on AM FM select The AM FM select control works in radio and tape modes AM FM select in radio mode This control allows you to select AM or FM frequency bands Press the AM control to select from AM selections and press the FM control to select from FM1 or FM2 memory preset stations AM FM select in tape mode Press this control to stop tape play and begin radio play 31 Controls and features Tune adjust The tune control works in radio mode Tune adjust in radio mode e Press lt q to move to the next frequency down the band whether or not a listenable station is located there Hold the control to move through the frequenc
132. njury or death if misused or mishandled Fuel ethanol and gasoline may contain benzene which is a cancer causing agent Observe the following guidelines when handling automotive fuel e Extinguish all smoking materials and any open flames before fueling your vehicle e Always turn off the vehicle before fueling e Automotive fuels can be harmful or fatal if swallowed Fuels such as gasoline and ethanol are highly toxic and if swallowed can cause 186 Maintenance and care death or permanent injury If fuel is swallowed call a physician immediately even if no symptoms are immediately apparent The toxic effects of fuel may not be visible for hours e Avoid inhaling fuel vapors Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation In severe cases excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury e Avoid getting fuel liquid in your eyes If fuel is splashed in the eyes remove contact lenses if worn flush with water for 15 minutes and seek medical attention Failure to seek proper medical attention could lead to permanent injury e Fuels can also be harmful if absorbed through the skin If fuel is splashed on the skin and or clothing promptly remove contaminated clothing and wash skin thoroughly with soap and water Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation e Be particularly careful if you ar
133. ntains high current fuses that protect your vehicle s main electrical systems from overloads Always disconnect the battery before servicing high current fuses Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs If the battery has been disconnected and reconnected refer to the Battery section of the Maintenance and care chapter 144 Roadside emergencies O 125 O MEGAFUSE f N Fo Fna fn A O oO E 2 ag Tw Ci CX ofl vB 0 r ea siete Ly tJ Ce ca w fl Ol aal onl res 20 lt j m E 7 ce X Z 2 ape 2 ee OF Baye oO fm fe a 7 I m 9 Ce pg sll att ols nnn anu LJ L Ue ted PEO The high current fuses are coded as follows Fuse Relay Fuse Amp Power Distribution Box Description Location Rating I P Fuse Panel Blower Motor Relay Module A C Relay NoUs o O odule i 20A Electronic Shift Relay and Electronic Shift Control Module 20A Fog Lamp and Daytime Running Lamps Powertrain Control Module 4 Wheel Anti lock Brake System 4WABS M PCM Relay 145 Trlr Tow Park Lamp Roadside emergencies Location Rating 9 20A Fuel Pump Relay and RAP Module 13 15A Heated Oxygen
134. ntenance Guide to determine the correct servi 3 Approximate dry capacity includes ce interval cooler and tubes Fluid level should be checked by a qualified service technician 240
135. nts have buckled their safety belts For more information on safety belts and their proper usage refer to the Seating and safety restraints chapter 100 Starting 2 Make sure the headlamps and vehicle accessories are off If starting a vehicle with an automatic transmission e Make sure the parking brake is set e Make sure the gearshift is in P Park If starting a vehicle with a manual transmission e Make sure the parking brake is set e Push the clutch pedal to the floor 3 Turn the key to 4 ON without turning the key to 5 START If there is difficulty in turning the key firmly rotate the steering wheel left and right until the key turns freely This condition may occur when e front wheels are turned e front wheel is against the curb e steering wheel is turned when getting in or out of the vehicle 101 Starting ENGINE lt FUEL DOOR FUEL RESET Ef Make sure the corresponding lights illuminate briefly If a light fails to illuminate have the vehicle serviced e If the driver s safety belt is fastened the A light may not illuminate STARTING THE ENGINE 1 Turn the key to 5 START without pressing the accelerator pedal and release as soon as the 3 4 engine starts The key will return to 4 ON 2 If the temperature is above 12 C 10 F and the engine does not start within five seconds on the f
136. o display the CLK button will not function in the above manner Controls and features n l Controls and features The CLK button will allow you to switch between media display mode radio station stereo information etc and clock display mode time When in clock mode the media information will display for 10 seconds when the radio is turned on and then revert to clock information Anytime that the media is changed new radio station etc the media information will again display for 10 seconds before reverting back to the clock In media mode the media information will always be displayed Mute mode Press the control to mute the playing media Press the control again to return to the playing media Cleaning compact discs Inspect all discs for contamination before playing If necessary clean discs only with an approved CD cleaner and wipe the center out to the edge Do not use circular motion Cleaning cassetie player if equipped Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation Cassette and cassette player care e Use only cassettes that are 90 minutes long or less e Do not expose tapes to direct sunlight high humidity extreme heat or extreme cold Allow tapes that may have been exposed to extreme temperatures to reach a moderate temperature before playing e Tighten very loose tapes by
137. o die than a person wearing a seat belt Your vehicle has special design and equipment features to make it capable of performing in a wide variety of circumstances These special design features such as larger tires and increased ground clearance give the vehicle a higher center of gravity than a passenger car Vehicles with a higher center of gravity such as utility and four wheel drive vehicles handle differently than vehicles with a lower center of gravity Utility and four wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low slung sports cars are designed to perform satisfactorily under off road conditions Avoid sharp turns excessive speed and abrupt maneuvers in these vehicles Failure to drive cautiously could result in an increased risk of vehicle rollover personal injury and death Loaded vehicles with a higher center of gravity may handle differently than unloaded vehicles Extra precautions such as slower speeds and increased stopping distance should be taken when driving a heavily loaded vehicle Your vehicle has the capability to haul more cargo and people than most passenger cars Depending upon the type and placement of the load hauling people and cargo may raise the center of gravity of the vehicle 110 Driving Use extra caution while becoming familiar with your vehicle Know the capabilities and limitations of both you as a driver and your vehicle AUTOMATI
138. o haul more cargo and people than most passenger cars Depending upon the type and placement of the load hauling cargo and people may raise the center of gravity of the vehicle 126 Driving Calculating the load your vehicle can carry tow 1 Use the appropriate maximum gross combined weight rating GCWR chart to find the maximum GCWR for your type engine and rear axle ratio 2 Weigh your vehicle as you customarily operate the vehicle without cargo To obtain correct weights try taking your vehicle to a shipping company or an inspection station for trucks 3 Subtract your loaded vehicle weight from the maximum GCWR on the following charts This is the maximum trailer weight your vehicle can tow and must fall below the maximum shown under maximum trailer weight on the chart TRAILER TOWING Your vehicle may tow a class I II or II trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your engine and rear axle ratio on the following charts Your vehicle s load capacity is designated by weight not by volume so you cannot necessarily use all available space when loading a vehicle Towing a trailer places an additional load on your vehicle s engine transmission axle brakes tires and suspension Inspect these components carefully after any towing operation 127 Driving Trailer towing table 4x2 manual transmission Maximum Maximum Maximum GCWR kg trailer frontal
139. o turn speed control off e Press OFF or e Turn off the vehicle ignition ae Once speed control is switched off the previously programmed set speed will be erased 55 Controls and features To set a speed e Press SET SET ACC SET ACCEL For speed control to operate the speed control must be ON and the vehicle speed must be greater than 48 km h 80 mph If you drive up or down a steep hill your vehicle speed may vary momentarily slower or faster than the set speed This is normal Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill If your vehicle speed is faster than the set speed while driving on a downhill you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed If your vehicle slows down more than 16 km h 10 mph below your set speed on an uphill your speed control will disengage This is normal Pressing RES RSM RESUME will re engage it Do not use the speed control in heavy traffic or on roads that are winding slippery or unpaved To set a higher set speed e Press and hold SET SET ACC SET ACCEL Release the control when the desired vehicle speed is reached or Press and release SET SET ACC SET ACCEL Each press will increase the set speed by 1 6 km h 1 mph or Accelerate with your accelerator pedal When the desired vehicle COAST speed is reached press and release SET SET ACC SET ACCEL 56 Control
140. of e three consumer representatives e a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm The dealership Board member is chosen from Ford and Lincoln Mercury dealership management recognized for their business leadership qualities What the Board needs To have your case reviewed you must complete the application in the DSB brochure and mail it to the address provided on the application form Some states will require you to use certified mail with return receipt requested Your application is reviewed and if it is determined to be eligible you will receive an acknowledgment indicating e the file number assigned to your application e the toll free phone number of the DSB s independent administrator Your dealership and a Ford Motor Company representative will then be asked to submit statements To properly review your case the Board needs the following information e legible copies of all documents and maintenance or repair orders relevant to the case e the year make model and Vehicle Identification Number VIN listed on your vehicle ownership license e the date of repair s and mileage at the time of occurrence s e the current mileage e the name of the dealer s who sold or serviced the vehicle e a brief description of your unresolved concern 222 Customer assistance e a brief summary of the action taken by
141. of these systems may result in vehicle starting problems and a loss of security protection Large metallic objects electronic devices on the key chain that can be used to purchase gasoline or similar items or a second key on the same key ring as the PATS ignition key may cause vehicle starting concern and record DTC s under certain conditions If present you need to keep these objects from touching the PATS ignition key while starting the engine These objects and devices cannot damage the PATS ignition key but can cause a momentary concern if they are too close to the key during engine start If a problem occurs turn ignition OFF and restart the engine with all 67 Controls and features other objects on the key ring held away from the ignition key Check to make sure the encoded ignition key is an approved Ford encoded ignition key Spare SecuriLock keys can be purchased from your dealership and programmed to your SecuriLock passive anti theft system Refer to Programming spare SecuriLock keys for more information If one or both of your SecuriLock keys are lost or stolen and you want to ensure the lost or stolen key will not operate your vehicle bring your vehicle and all available SecuriLock keys to your dealership for reinitialization Theft indicator The theft indicator on the instrument cluster will operate as follows e When the ignition is OFF the theft indicator will flash briefly every two seconds to indica
142. off the engine and remove the key 3 Block the wheels to prevent the vehicle from moving unexpectedly e Manual transmission 1 Set the parking brake 2 Depress the clutch and place the gearshift in 1 First 158 Maintenance and care 3 Turn off the engine and remove the key 4 Block the wheels to prevent the vehicle from moving unexpectedly Working with the engine on e Automatic transmission 1 Set the parking brake and ensure the gearshift is securely latched in P Park 2 Block the wheels to prevent the vehicle from moving unexpectedly Do not start your engine with the air cleaner removed and do not remove it while the engine is running e Manual transmission 1 Set the parking brake depress the clutch and place the gearshift in N Neutral 2 Block the wheels to prevent the vehicle from moving unexpectedly Do not start your engine with the air cleaner removed and do not remove it while the engine is running OPENING THE HOOD qm 1 Inside the vehicle pull the hood release handle located under the bottom of the instrument panel 2 Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood 3 Lift the hood and support it with the prop rod 159 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2 5L 14 engine a iP HP LL 7 Engine coolant reservoir Windshield washer fluid
143. om the ground metal surface 155 Roadside emergencies 2 Remove the jumper cable on the negative connection of the booster vehicle s battery 3 Remove the jumper cable from the positive terminal of the booster vehicle s battery 4 Remove the jumper cable from the positive terminal of the disabled vehicle s battery After the disabled vehicle has been started and the jumper cables removed allow it to idle for several minutes so the engine computer can relearn its idle conditions 156 Roadside emergencies WRECKER TOWING If you need to have your vehicle towed contact a professional towing service or if you are a member your roadside assistance center It is recommended that your vehicle be towed with a wheel lift or flatbed equipment Do not tow with a slingbelt Ford Motor Company has not approved a slingbelt towing procedure On 4x2 vehicles it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground On 4x4 vehicles it is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment with all the wheels off the ground If the vehicle is towed by other means or incorrectly vehicle damage may occur Ford Motor Company provides a towing manual for all authorized tow truck operators Have your tow truck operator refer to this manual for proper hook up and towing procedure
144. omentarily release the pedal and repeat the squeeze technique e We recommend that you familiarize yourself with how the RABS performs However avoid unnecessary risks Four wheel anti lock brake system ABS if equipped On vehicles equipped with an anti lock braking system ABS a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events Pedal pulsation coupled with noise while braking under panic conditions or on loose gravel bumps wet or snowy roads is normal and indicates proper functioning of the vehicle s anti lock brake system If the vehicle has continuous vibration or shudder in the steering wheel while braking the vehicle should be inspected by a qualified service technician The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency The wheels are prevented from locking even when the brakes are firmly applied The accompanying illustration depicts the advantage of an ABS equipped vehicle on bottom to a non ABS equipped vehicle on top during hard braking with loss of front braking traction 107 Driving ABS warning lamp s The 3 warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position If the light does not illuminate momentarily at start up remains on or continues to flash the ABS needs to be serviced With the ABS light on the anti
145. on or extend the ball hitch rearward will significantly increase the loads on the bumper and its attachments This can result in the failure of the bumper or the bumper attachments Use of any type of hitch extensions should be considered abuse Trailer tow connector The trailer tow connector is located under the rear bumper on the driver s side of the vehicle Refer to the following chart for information regarding the factory equipped trailer tow connector 133 Driving Trailer tow connector 1 Dark Green Trailer right Circuit activated when brake hand turn signal pedal is depressed or when ignition is on and right hand turn signal is applied 2 Yellow Trailer left hand Circuit activated when brake turn signal pedal is depressed or when ignition is on and left hand turn signal is applied 3 Tan White Tail lamp Relay controlled circuit activated when the park lamps headlamps are on 4 White Ground Matching vehicle circuit returns to battery s negative ground Driving while you tow When towing a trailer e Ensure that you turn off your speed control The speed control may shut off automatically when you are towing on long steep grades e Consult your local motor vehicle speed regulations for towing a trailer e Use a lower gear when towing up or down steep hills This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling e Anticipate stops and b
146. on wearing the belt to move forward enough to incur a serious or fatal injury The more severe the crash and the heavier the occupant the greater the risk is Be sure the air bag is turned ON for any person who does not qualify under the Transport Canada deactivation criteria 92 Seating and safety restraints SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children Also see Air Bag Supplemental Restraint System CSRS in this chapter for special instructions about using air bags Important child restraint precautions You are required by law to use safety restraints for children in the U S and Canada If small children ride in your vehicle generally children who are four years old or younger and who weigh 18 kg 40 lbs or less you must put them in safety seats made especially for children Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision Always follow the instructions and warnings that come with any infant or child restraint you might use When possible always place children under age 12 in the rear seat of your vehicle Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the fron
147. ongue between the child seat and the release button to prevent accidental unbuckling Place seat back in upright position Put the safety belt in the automatic locking mode Refer to Automatic locking mode passenger side front and outboard rear seating positions if equipped Carefully follow all of the manufacturer s instructions included with the safety seat you put in your vehicle If you do not install stop or collision 95 Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions 1 Position the child safety seat in a seat with a combination lap and shoulder belt An air bag can kill or injure a child in a child seat If you must use a forward facing child seat in the front seat move seat all the way back An air bag can kill or injure a child in a child seat Child seats should never be placed in the front seats unless passenger air bag switch is turned off See Passenger air bag deactivation switch Rear facing child seats should NEVER be placed in the front seats unless the passenger airbag switch is turned off 2 Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together 96 Seating and safety restraints 3 While holding the shoulder and lap belt portions together route the tongue through the child seat according to the child seat manufacturer s instructions Be sure the belt webbing is not twisted
148. options Geiting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle When you need warranty repairs your selling dealer would like you to return to it for that service but you may also take your vehicle to another Ford Motor Company or Ford of Canada dealership authorized for warranty repairs Certain warranty repairs require special training though so not all dealers are authorized to perform all warranty repairs That means that depending on the warranty repair needed the vehicle may need to be taken to another dealer If a particular dealership can not assist you then contact the Customer Assistance Center 218 Customer assistance If you have questions or concerns or are unsatisfied with the service you are receiving follow these steps 1 Contact your Sales Representative or Service Advisor at your selling servicing dealership 2 If your inquiry or concern remains unresolved contact the Sales Manager or Service Manager at the dealership 3 If the inquiry or concern cannot be resolved at the dealership level please contact the Ford Customer Assistance Center Ford Motor Company and Ford of Canada dealerships also carry quality parts and accessories providing you with equipment reliability Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service or if you need more help than the dealership could
149. or three seconds followed by three seconds with the safety belt warning light off then followed by flashing the safety belt warning light four times per second for three seconds again 9 After receiving confirmation the deactivation activation procedure is complete Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged Inspect the safety belts to make sure there are no nicks wears or cuts replacing if necessary All safety belt assemblies including retractors buckles front seat belt buckle assemblies buckle support assemblies slide bar if equipped shoulder belt height adjusters Gf equipped shoulder belt guide on seatback if equipped child safety seat tether bracket assemblies if equipped and attaching hardware should be inspected after a collision Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced However if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly they do not need to be replaced Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision Refer to Cleaning and maintaining the s
150. ord Extended Service Plan You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan Ford ESP coverage Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company in the U S and Ford of Canada Gin Canada It provides the following e benefits during the warranty period depending on the plan you purchase such as reimbursement for rentals coverage for certain maintenance and wear items e protection against repair costs after your Bumper to Bumper Warranty expires You may purchase Ford ESP from any participating Ford and Lincoln Mercury and Ford of Canada dealer There are several plans available in various time distance and deductible combinations which can be tailored to fit your own driving needs Ford ESP also offers reimbursement benefits for towing and rental coverage In Hawaii rules vary See your dealer for details When you buy Ford ESP you receive Peace of Mind protection throughout the United States and Canada provided by a network of more than 5 000 participating Ford or Lincoln Mercury and Ford of Canada dealers If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle you may still be eligible Please contact your dealer for further information Since this information is subject to change please ask your dealer for complete details about Ford Extended Service Plan coverage
151. ormation will always be displayed AM FM Stereo Single CD Radio VOL PUSH ON OE O Vv osc V S a TUNE lt nscs gt e O00000 Volume power control Press the control to turn the audio VOL PUSH ON system on or off C 37 Controls and features Turn the control to raise or lower K DN volume VOL PUSH ON If the volume is set above a certain level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition switch is turned back on AM FM select The AM FM select control works in radio and CD modes AM FM select in radio mode This control allows you to select AM or FM frequency bands Press the control to switch between AM FM1 or FM2 memory preset stations AM FM select in CD mode Press this control to stop CD play and begin radio play Tune adjust The tune control works in radio and CD changer mode if equipped Tune adjust in radio mode e Press lt to move to the next frequency down the band 4 SEEK p whether or not a listenable station is located there Hold the y control to move through the frequencies quickly 38 Controls and features e Press p to move to the next frequency up the band whether or not a listenable station is located there Hold for quick movement Tune adjust for CD changer if equipped e Press lt to select the previous disc in the C
152. ot allow the engine to relearn its idle trim the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned If the battery has been disconnected or a new battery has been installed the clock and the preset radio stations must be reset once the battery is reconnected e Always dispose of automotive P batteries in a responsible manner s S Follow your local authorized he A standards for disposal Call your 4 local authorized recycling center to find out more about recycling automotive batteries RECYCLE WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades Checking the wiper blades If the wiper blades do not wipe properly clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent Rinse thoroughly with clean water To avoid damaging the blades do not use fuel kerosene paint thinner or other solvents 180 Maintenance and care Changing the wiper blades To replace the wiper blades 1 Pull the wiper arm away from the windshield and lock into the service position 2 Turn the blade at an angle from the wiper arm Push the lock pin gt manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm
153. ou will need to have two previously programmed SecuriLock keys and the new unprogrammed SecuriLock key readily accessible for the procedure Please read and understand the entire procedure before you begin 1 Insert the first previously programmed SecuriLock key into the ignition and turn the ignition from OFF to ON maintain ignition in ON for at least one second 2 Turn ignition to OFF and remove the first SecuriLock key from the ignition 3 Within five seconds of turning the ignition to OFF insert the second previously programmed SecuriLock key into the ignition and turn the ignition from OFF to ON maintain ignition in ON for at least one second but no more than five seconds 4 Turn the ignition to OFF and remove the second SecuriLock key from the ignition 5 Within 10 seconds of turning the ignition to OFF insert the unprogrammed SecuriLock key new key valet key into the ignition and turn the ignition from OFF to ON maintain ignition in ON for at least one second This step will program your new SecuriLock key 6 To program additional SecuriLock key s repeat this procedure from step 1 If the programming procedure was successful the new SecuriLock key s will start the vehicle s engine The theft indicator located on the instrument cluster will light for three seconds and then go out If the programming procedure was not successful the new SecuriLock key s will not operate the
154. oved by moving your vehicle slowly while applying light pressure on the brake pedal Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage 124 Driving VEHICLE LOADING Before loading a vehicle familiarize yourself with the following terms Base Curb Weight Weight of the vehicle including any standard equipment fluids lubricants etc It does not include passengers or aftermarket equipment Payload Combined maximum allowable weight of cargo passengers and optional equipment The payload equals the gross vehicle weight rating minus base curb weight GVW Gross Vehicle Weight Base curb weight plus payload weight The GVW is not a limit or a specification GVWR Gross Vehicle Weight Rating Maximum total weight of the base vehicle passengers optional equipment and cargo The GVWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver s door pillar GAWR Gross Axle Weight Rating Carrying capacity for each axle system The GAWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver s door pillar GCW Gross Combined Weight The combined weight of the towing vehicle including passengers and cargo and the trailer GCWR Gross Combined Weight Rating Maximum combined weight of towing vehicle including passengers and cargo and the trailer The GCWR indica
155. parking brake released 10 Instrumentation Turn signal Iluminates when the left or right turn signal or the hazard lights are a o gt turned on If one or both of the indicators stay on continuously or flash faster check for a burned out turn signal bulb Refer to Exterior bulbs in the Maintenance and care chapter High beams Illuminates when the high beam headlamps are turned on D Anti theft system if equipped Refer to SecuriLock passive anti theft system in the Controls and features chapter THEFT Charging system Illuminates when the ignition is turned to the ON position and the engine is off The light also illuminates when the battery is not charging properly requiring electrical system service O D off if equipped Illuminates when the Transmission o D Control Switch TCS refer to Overdrive control in the Controls OFF and Features chapter has been pushed turning the transmission overdrive function OFF When the light is on the transmission does not operate in the overdrive mode refer to the Driving chapter for transmission function and operation The light may also flash steadily if a transmission malfunction is detected If the light does not come on when the Transmission Control Switch is depressed or if the light flashes steadily have your vehicle serviced as soon as possible damage to the transmission could occur 11 Instrumentation Check gage if equipped Illuminates
156. peaker sound distribution can be adjusted between the right and left speakers Press the BAL control then press lt to shift sound to the left and e to shift sound to the right Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers Press the FADE control then press gt to shift the sound to the front and e lt 4 to shift the sound to the rear A A 48 Controls and features Tape select e To begin tape play with a tape loaded into the audio system z cD while in the radio or CD mode press the TAPE control Press the button during rewind or fast forward to stop the rewind or fast forward function Rewind The rewind control works in tape and CD modes e In tape mode radio play will continue until rewind is stopped with the TAPE control or the beginning of the tape is reached e In CD mode pressing the REW control rewinds the CD within the current track Fast forward The fast forward control works in tape and CD modes q e In the tape mode tape direction will automatically reverse when the end of the tape is reached e In CD mode pressing the control fast forwards the CD within the current track Tape direction select Press SIDE 1 2 to play the alternate side of a tape E qe Eject function Press the EJ control to stop and eject a tape gt 49 Controls and features Press
157. position rotate the control upward for fast intervals and downward for slow intervals Push tap the end of the stalk briefly for a single swipe no wash Push and hold for three swipes with wash Push and hold for a longer wash up to ten seconds POWER WINDOWS IF EQUIPPED Press and hold the rocker switches to open and close windows e Press the top portion of the I I rocker switch to close x e Press the bottom portion of the rocker switch to open 61 Controls and features One touch down e Press AUTO completely down and release quickly The driver s window will open fully Depress again to stop window operation One touch down can be deactivated during operation by pushing up on the power window control POWER DOOR LOCKS IF EQUIPPED Press the top of the control to unlock all doors and the bottom to lock all doors POWER SIDE VIEW MIRRORS IF EQUIPPED To adjust your mirrors 1 Select lt q to adjust the left mirror or gt to adjust the right mirror 2 Move the control in the direction you wish to tilt the mirror 3 Return to the center position to lock mirrors in place 62 Controls and features CENTER CONSOLE IF EQUIPPED Your vehicle may be equipped with a variety of console features These include e Utility compartment with cassette compact disc storage e Cupholders e Coin holder slots e Flip up armrest e Removable utility bag if equipp
158. possibly causing a fire Instrumentation Fuel reset if equipped Illuminates when the ignition key is turned to the ON position and the FUEL fuel pump shut off switch has been triggered For more information RESET refer to Fuel pump shut off switch in the Roadside emergencies chapter Air bag readiness Momentarily illuminates when the O O ignition is turned ON If the light G fails to illuminate continues to flash PV or remains on have the system serviced immediately Safety belt Momentarily illuminates when the ignition is turned to the ON position P to remind you to fasten your safety belts For more information refer to the Seating and safety restraints chapter Brake system warning Momentarily illuminates when the ignition is turned to the ON O position Also illuminates if the BRAKE parking brake is engaged If the brake warning lamp does not illuminate at these times seek service immediately Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately Anti lock brake system ABS Momentarily illuminates when the ignition is turned to the ON position If the light remains on continues to flash or fails to illuminate have the system serviced immediately With the ABS light on the anti lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with the
159. r lamps ccccceeee 202 replacing bulbs 197 199 200 201 Lane change indicator see Turn signal eeee 54 Lights warning and indicator 8 Index AIL DAG seee e eE 10 anti lock brakes ABS 10 108 anti theft osrin sinansa 11 Prak seszidsiessssicszeiaedtesaaesescsawnasesss 10 charging system sissirsissiisss 11 check coolant sisseripikimirirs 12 Check CNSINE ersari 8 cruise indicator niesienia 12 door ajal edie vessessinacaseanveeieesasveceee 12 fuel reset oo ececcccseeseceeseaeees 10 High BEAM 2 cts sesso tiain 11 overdrive Off oo cecccceeeseeeees 11 Safety belt ccccccsesneseeeeee 10 speed control eeeeeeeeeeees 59 turn signal indicator 11 Road Winnits ssesisgscsscagshvcsssisessavt 125 GAWR cdsessitsiaotcliacisecienanaens 125 GV WIR ae rener SaS 125 trailer tOWINE eisireraciocrenas 125 Loading instructions 126 Lubricant specifications 212 214 Lumbar support seats 0 0 0 0 71 Manual transmission 06 116 fluid capacities 0 0 0 209 lubricant specifications 214 Ag Sh1LSs ol emer er S 118 Mirrors CLEANING sascssesigesernieieiveasnenan 208 side view mirrors power 62 Motorcraft parts 0 192 209 Octane Tating xssccrcaxeescecrscenesvees 190 OdOMmELET eseeienenogee ge 16 Oil see Engine oil 08 163 Overdrive sisisi ccccessccseeseeseeseneees 59 Panic alarm feature remote entry SYSTEM
160. r side and end of the vehicle to the tire being changed If the vehicle slips off the jack you or someone else could be seriously injured 1 Park on a level surface activate hazard flashers and place gearshift lever in P Park automatic transmission or 1 First manual transmission 2 Set the parking brake and turn engine OFF 3 Block the diagonally opposite wheel 150 Roadside emergencies 4 Insert tapered end of the lug wrench behind hub caps and twist them off 5 Loosen each wheel lug nut one half turn counterclockwise but do not remove them until the wheel is raised off the ground 6 Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm 1 inch off the ground e Front e Rear 151 Roadside emergencies To lessen the risk of personal injury do not put any part of your body under the vehicle while changing a tire Do not start the engine when your vehicle is on the jack The jack is only meant for changing the tire e Never use the differential as a jacking point 7 Remove the wheel lug nuts with the lug wrench 8 Replace the flat tire with the spare tire making sure the valve stem is facing outward Reinstall the lug nuts until the wheel is snug against the hub Do not fully tighten the lug nuts until the wheel has been lowered 9 Lower the wheel by turning the jack handle counterclockwi
161. r the fuel gauge indicates empty The amount of empty reserve varies and should not be relied upon to increase driving range When refueling your vehicle after the fuel gauge indicates empty you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank For consistent results when filling the fuel tank e Use the same filling rate setting dow medium high each time the tank is filled e Allow three automatic click offs when filling e Always use fuel with the recommended octane rating 192 Maintenance and care e Use a known quality gasoline preferably a national brand e Use the same side of the same pump and have the vehicle facing the same direction each time you fill up e Have the vehicle loading and distribution the same every time Your results will be most accurate if your filling method is consistent Calculating fuel economy 1 Fill the fuel tank completely and record the initial odometer reading in kilometers or miles 2 Each time you fill the tank record the amount of fuel added in liters or gallons 3 After at least three to five tank fill ups fill the fuel tank and record the current odometer reading 4 Subtract your initial odometer reading from the current odometer reading 5 Follow one of the simple calculations in order to determine fuel economy Multiply liters used by 100 then divide by total kilo
162. radio transmitters Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician Mobile communications systems may harm the operation of your vehicle particularly if they are not properly designed for automotive use or are not properly installed When operated such systems may cause the engine to stumble or stall In addition such systems may be damaged or their performance may be affected by operating your vehicle Citizens band CB transceivers garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your vehicle s operation Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment 228 Customer assistance ORDERING ADDITIONAL OWNER S LITERATURE To order the publications in this portfolio Make checks payable to HELM INCORPORATED P O Box 07150 Detroit Michigan 48207 For a free publication catalog order toll free 1 800 782 4356 Monday Friday 8 00 a m 6 00 p m EST for credit card holders only Obtaining a French owner s guide French Owner s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada Limited Service Publications P O Box 1580 Station B Mississauga Ontario L4Y 4G3 229 Reporting safety defects REPORTING SAFETY DEFECTS U S ONLY If you believe that your v
163. rake gradually Exceeding the GCWR rating may cause internal transmission damage and void your warranty coverage Servicing after towing If you tow a trailer for long distances your vehicle will require more frequent service intervals Refer to your Scheduled Maintenance guide for more information Trailer towing tips e Practice turning stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination When turning make wider turns so the trailer wheels will clear curbs and other obstacles 134 Driving e Allow more distance for stopping with a trailer attached e The trailer tongue weight should be no more than 10 15 of the loaded trailer weight e After you have traveled 80 km 50 miles thoroughly check your hitch electrical connections and trailer wheel lug nuts e When stopped in traffic for long periods of time in hot weather place the gearshift in P Park automatic transmissions or N Neutral manual transmissions This aids engine cooling and air conditioner efficiency e Vehicles with trailers should not be parked on a grade If you must park on a grade place wheel chocks under the trailer s wheels Launching or retrieving a boat When backing down a ramp during boat launching or retrieval e Do not allow the static water level to rise above the bottom edge of the rear bumper and e Do not allow waves to break higher than 15 cm 6 inches above the bot
164. reservoir Transmission fluid dipstick automatic transmission Engine oil dipstick Brake fluid reservoir Power distribution box Clutch fluid reservoir manual transmission Battery OoOmnNIa or wonder Power steering fluid reservoir 10 Engine oil filler cap 11 Air filter assembly 160 Maintenance and care 3 0L V6 engine 1 2 3 4 5 6 7 J 11 10 9 Engine coolant reservoir Windshield washer fluid reservoir Engine oil filler cap Transmission fluid dipstick automatic transmission Engine oil dipstick Brake fluid reservoir Power distribution box Clutch fluid reservoir ooN eN Battery 10 Power steering fluid reservoir 11 Air filter assembly 161 Maintenance and care 4 0L OHV V6 engine SNR WIGGLE LIKES mt SA R COPA te 1 Windshield washer fluid reservoir 2 Engine oil filler cap 3 Transmission fluid dipstick automatic transmission 4 Engine oil dipstick 5 Power steering fluid reservoir 6 Brake fluid reservoir 7 Power distribution box 8 Clutch fluid reservoir manual transmission 9 Battery 10 Air filter assembly 11 Engine coolant reservoir 162 Maintenance and care ENGINE OIL S27 Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil 1 Make sure t
165. river and front passenger Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder 76 Seating and safety restraints e Regular Cab and 4 door Super Cab e 2 door SuperCab To lower the shoulder belt height push the button and slide the height adjuster down To raise the height of the shoulder belt slide the height adjuster up Pull down on the height adjuster to make sure it is locked in place Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision 77 Seating and safety restraints Lap belts Adjusting the front center seat lap belt if equipped The lap belt does not adjust automatically The lap belts should fit snugly and as low as possible around the hips not around the waist Insert the tongue into the correct buckle the buckle closest to the direction the tongue is coming from To lengthen the belt turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle To tighten the belt pull the loose end of the belt through the tongue until it fits snugly across the hips Shorten and fasten the belt when not in use Adjusting the rear center facing jump seat lap belt if equipped The lap belt will adjust automatically To fasten grasp the tongue
166. rn vehicles are designed to work as a safety system with the air bags Read all air bag Warning labels in the vehicle as well as the other important air bag instructions and Warnings in this Owner s Guide NHTSA deactivation criteria excluding Canada 1 Infant An infant less than 1 year old must ride in the front seat because e the vehicle has no rear seat e the vehicle has a rear seat too small to accommodate a rear facing infant seat or 90 Seating and safety restraints e the infant has a medical condition which according to the infant s physician makes it necessary for the infant to ride in the front so that the driver can constantly monitor the child s condition 2 Child age 1 to 12 A child age 1 to 12 must ride in the front seat because e the vehicle has no rear seat e although children ages 1 to 12 ride in the rear seat s whenever possible children ages 1 to 12 sometimes must ride in the front because no space is available in the rear seat s of the vehicle or e the child has a medical condition which according to the child s physician makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child s condition 3 Medical condition A passenger has a medical condition which according to his or her physician e causes the passenger air bag to pose a special risk for the passenger and e makes the potential harm from the passenger air bag in a
167. rolyte level Refer to the Scheduled Maintenance Guide for the service interval schedules Keep the electrolyte level in each cell up to the level indicator Do not overfill the battery cells If the electrolyte level in the battery is low you can add plain tap water to the battery as long as you do not use hard water water with a high mineral or alkali content If possible however try to only fill the battery cells with distilled water If the battery needs water often have the charging system checked If your battery has a cover shield make sure it is reinstalled after the battery has been cleaned or replaced For longer trouble free operation keep the top of the battery clean and dry Also make certain the battery cables are always tightly fastened to the battery terminals If you see any corrosion on the battery or terminals remove the cables from the terminals and clean with a wire brush You can neutralize the acid with a solution of baking soda and water 178 Maintenance and care Batteries normally produce explosive gases which can cause personal injury Therefore do not allow flames sparks or lighted substances to come near the battery When working near the battery always shield your face and protect your eyes Always provide proper ventilation When lifting a plastic cased battery excessive pressure on the end walls could cause acid to flow through the vent caps resulting in personal injury and or
168. rts manual transmission oe Coolant capacity 3 0L V6 with 14 0L 14 8 quarts automatic transmission ee Coolant capacity 4 0L V6 with 13 0L 13 7 quarts manual transmission epee Coolant capacity 4 0L V6 with 12 5L 13 2 quarts Fr nr ear an a Power steering fluid capacity Fill to range on dipstick Use porase tee ocr MERCON ATE 239 Hood release Pull handle under the left side of the instrument panel Filling station informatio Item Manual transmission fluid capacity Automatic transmission fluid capacity 4x2 vehicles with 14 engine Automatic transmission fluid capacity 4x2 vehicles with V6 engine capacity 4x4 vehicles Windshield washer fluid 1 Use Ford Premium Engine Coolant n 2 65L 2 8 quarts Use Motorcraft MERCON ATF 9 4L 9 9 quarts Use Motorcraft MERCONEV ATE 3 9 5L 10 0 quarts Use Motorcraft MERCON V ATF 9 8L 10 3 quarts Use Motorcraft MERCON V ATF 2 6L 2 75 quarts Use Ultra Clear Windshield Washer Concentrate green in color DO NOT USE Ford Extended Life Engine Coolant orange in color Refer to Adding engine coolant in the Maintenance and Care chapter 2 Ensure the correct automatic trans mission fluid is used Transmission fluid requirements are indicated on the dipstick or on the dipstick handle MERCON and MERCON V are not interchangeable DO NOT mix MERCON and MERCON V Refer to your Scheduled Mai
169. s Never use abrasives that will damage the finish of special wheel surfaces Use a tar remover to remove grease and tar The brushes used in some automatic car washes may damage the finish on your wheels Before going to a car wash find out if the brushes are abrasive Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal When washing e Take care when using a power washer to clean the engine The high pressure fluid could penetrate the sealed parts and cause damage e Do not spray with cold water to avoid cracking the engine block or other engine components Cover the highlighted areas to prevent water damage when cleaning the engine 204 Maintenance and care e 4 0L e 3 0L CY rR 2 a FAZY OS We JA a 205 Maintenance and care e 2 5L Com h HN S VE J FNY lt P pa e Never wash or rinse the engine while it is running water in the running engine may cause internal damage Cleaning non painted plastic exterior parts Use vinyl cleaner for routine cleaning Clean with a tar remover if necessary Do not clean plastic parts with thinners solvents or petroleum based cleaners Cleaning the exterior lamps Wash with the same detergen
170. s and features You can accelerate with the accelerator pedal at any time during speed control usage Releasing the accelerator pedal will return your vehicle to the previously programmed set speed To set a lower set speed e Press and hold CST COAST Release the control when the desired speed is reached or Press and release CST COAST Each press will decrease the set speed by 1 6 km h 1 mph or Depress the brake pedal When the desired vehicle speed is reached press SET SET ACC SET ACCEL 57 Controls and features To disengage speed control e Depress the brake pedal or e Depress the clutch pedal if equipped Disengaging the speed control will not erase the previously programmed set speed Pressing OFF will erase the previously programmed set speed 58 To return to a previously set speed e Press RES RSM RESUME For RES RSM RESUME to operate the vehicle speed must be faster than 48 km h 30 mph Indicator light if equipped This light comes on when either the SET ACC SET ACCEL or RES RSM RESUME controls are pressed It turns off when the speed control OFF control is pressed the brake is applied or the ignition is turned to the OFF position Controls and features SPEED CONT OVERDRIVE CONTROL IF EQUIPPED Activating overdrive Overdrive is the normal drive position for the best fuel economy The overdrive function allows automatic upshifts and downshifts throu
171. s for your vehicle 157 Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle e We highlight do it yourself items in the engine compartment for easy location e We provide a Scheduled Maintenance Guide which makes tracking routine service easy If your vehicle requires professional service your dealership can provide necessary parts and service Check your Warranty Guide to find out which parts and services are covered Use only recommended fuels lubricants fluids and service parts conforming to specifications Motorcraft parts are designed and built to provide the best performance in your vehicle PRECAUTIONS WHEN SERVICING YOUR VEHICLE Be especially careful when inspecting or servicing your vehicle e Do not work on a hot engine e When the engine is running make sure that loose clothing jewelry or long hair does not get caught up in moving parts e Do not work on a vehicle with the engine running in an enclosed space unless you are sure you have enough ventilation Keep all lit cigarettes open flames and other lit material away from the battery and all fuel related parts If you disconnect the battery the engine must relearn its idle conditions before your vehicle will drive properly as explained in Battery in this chapter Working with the engine off e Automatic transmission 1 Set the parking brake and ensure the gearshift is securely latched in P Park 2 Turn
172. s on your vehicle are properly aimed at the assembly plant If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician 202 Maintenance and care CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford approved cleaners polishes and waxes Washing your vehicle Wash your vehicle regularly with cold or lukewarm water Never use strong detergents or soap If your vehicle is particularly dirty use a quality car wash detergent Always use a clean sponge washing glove or similar device and plenty of water for best results To avoid spots avoid washing when the hood is still warm immediately after or during exposure to strong sunlight During winter months it is especially important to wash the vehicle on a regular basis Large quantities of dirt and road salt are difficult to remove and also cause damage to the vehicle Any gasoline spilled on the vehicle or deposits such as bird droppings should be washed and sponged off as soon as possible Deposits not removed promptly can cause damage to the vehicle s paintwork Remove any exterior accessories such as antennas before entering a car wash If you have wax applied to the vehicle at a commercial car wash it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield After washing apply the brakes several
173. se 10 Remove the jack and fully tighten the lug nuts in the order shown 11 Stow the flat tire Refer to Stowing the spare tire 12 Stow the jack and lug wrench Make sure the jack is fastened so it does not rattle when you drive 13 Unblock the wheels JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames sparks or lit cigarettes An explosion could result in injury or vehicle damage Do not push start your vehicle You could damage the catalytic converter Batteries contain sulfuric acid which can burn skin eyes and clothing if contacted 152 Roadside emergencies Do not attempt to push start your vehicle Automatic transmissions do not have push start capability Preparing your vehicle 1 Use only a 12 volt supply to start your vehicle 2 Do not disconnect the battery of the disabled vehicle as this could damage the vehicle s electrical system 3 Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts 4 Check all battery terminals and remove any excessive corrosion before you attach the battery cables Ensure that vent caps are tight and level 5 Turn the heater fan on in both vehicles to protect any electrical surges Turn all other accessories off Connecting the jumper cables 1 Conne
174. se this vehicle as an ambulance Your vehicle is not equipped with the Ford Ambulance Preparation Package Electric vehicles For information on operating your Electric Vehicle also refer to the Electric Vehicle Owner s Guide Supplement Introduction These are some of the symbols you may see on your vehicle Vehicle Symbol Glossary Safety Alert Fasten Safety Belt Air Bag Side Child Seat Installation Warning Brake System Brake Fluid Non Petroleum Based Master Lighting Switch Fog Lamps Front Fuel Pump Reset Windshield Defrost Demist Power Windows Front Rear Be gt PENG yi ABA See Owner s Guide Air Bag Front Child Seat Child Seat Tether Anchorage Anti Lock Brake System Traction Control Hazard Warning Flasher Fuse Compartment Windshield Wash Wipe Rear Window Defrost Demist Power Window Lockout Introduction Vehicle Symbol Glossary Child Safety Door Lock Unlock Panic Alarm Engine Coolant Do Not Open When Hot Avoid Smoking Flames or Sparks Explosive Gas Power Steering Fluid Emission System Passenger Compartment bg Air Filter E Bx Interior Luggage Compartment Release Symbol Engine Oil Engine Coolant Temperature Battery Battery Acid Fan Warning Maintain Correct Fluid Level Engine Air Filter Jack ASX D gt LI fi y e h aja Instrumentation Instrument panel Instrument cluster dimmer swi
175. ssengers and cargo and the loaded trailer must not exceed the Gross Combined Weight Rating GCWR 4 64 3 628 0 1 887 4 64 8 000 0 4 160 50 4 64 64 Do not exceed the GVWR or the GAWR specified on the certification label 131 Driving Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage transmission axle damage structural damage loss of control and personal injury Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle See your dealer or a reliable trailer dealer if you require assistance Hitches For towing trailers up to 907 kg 2 000 lb use a weight carrying hitch and ball which uniformly distributes the trailer tongue loads through the underbody structure Use a frame mounted weight distrubuting hitch for trailers over 907 kg 2 000 Ib Do not install a single or multi clamp type bumper hitch or a hitch which attaches to the axle Underbody mounted hitches are acceptable if they are installed properly Follow the towing instructions of a reputable rental agency Whenever a trailer hitch and hardware are removed make sure all mounting holes in the underbody are properly sealed to prevent noxious gases or water from entering Safety chains Always connect the trailer s safety chains to the frame or hook retainers of the vehicle To connect the trailer s safety chains cross the chains u
176. ssn tarena 64 Parking brake scrisssussssrsscusss 108 Parts see Motorcraft parts 209 Power distribution box see FUSES elivsssacceisseacsssigeactess 144 Power door locks cccccee 62 Power steering prousiiesicrois s 109 234 fluid checking and adding 173 fluid refill capacity 0 209 fluid specifications 212 214 Preparing to drive your vehicle 08 110 Radios acted esidasssdisnetiiaatiasscariead ease 26 TROL VS erea setae 140 Remote entry system 63 64 illuminated entry oo 67 locking unlocking doors 64 PANIC AAI sireci 64 replacement additional trans MI LETS csser resperit 66 replacing the batteries 65 Safety belts see Safety restraints 13 72 73 74 75 76 Safety defects reporting 230 Safety restraints 72 73 74 75 76 Delt MINGE ss csed coenkedevcesedecbdscepecs 80 cleaning the safety belts 83 207 extension assembly 00 79 fop ad lts speria 73 74 75 76 FOF children cses cases dvsssedscvzenv seks 93 lap belt aiena 78 warning light and chime seissy 10 13 79 Safety seats for children 94 Seat belts see Safety restraints 72 OCAS Sih e vecsaneseratat Ges 70 child safety seats 0 0 94 SecuriLock passive anti theft system 67 68 69 Servicing your vehicle 158 SNOWDPIOWING ssrsiisessirnorirenisiae 3 Spark plugs specifications
177. state law What kinds of cases does the Board review Unresolved warranty repair concerns or vehicle performance as designed concerns on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review except those involving e anon Ford product e anon Ford dealership e sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle s performance as designed e a request for reimbursement of consequential expenses unless a service or product concern is being reviewed e items not covered by the New Vehicle Limited Warranty including maintenance and wear items e alleged personal injury property damage claims e cases currently in litigation e vehicles not used primarily for family personal or household purposes except in states where the Dispute Settlement Board is required to review commercial vehicles e vehicles with non U S warranties 221 Customer assistance Concerns are ineligible for review if the New Vehicle Limited Warranty has expired at receipt of your application and in certain states eligibility is dependent upon the customer s possession of the vehicle Eligibility may differ according to state law For example see the unique brochures for California West Virginia Georgia and Wisconsin purchasers lessees Board membership The Board consists
178. t allows you to set strong radio stations without losing your original manually set preset stations This feature is helpful on trips when you travel between cities with different radio stations 46 Controls and features Starting autoset memory preset 1 Select a frequency using the AM FM select controls 2 Press the AUTO control 3 When the first six strong stations are filled the station stored in memory preset control 1 will start playing If there are less than six strong stations available on the frequency band the remaining memory preset controls will all store the last strong station available These stations are temporarily stored in the memory preset controls until deactivated and are accessed in the same manner of your original presets To deactivate autoset and return to your audio system s manually set memory stations press the AUTO control again Bass adjust The bass adjust control allows you to increase or decrease the audio P system s bass output x Press the BASS control then press lt to decrease the bass output and gt to increase the bass output Treble adjust The treble adjust control allows you to increase or decrease the audio system s treble output 47 Controls and features Press the TREB control then press lt to decrease the treble output and e gt to increase the treble output A A Speaker balance adjust S
179. t as the exterior of your vehicle If necessary use a tar remover such as Ford Extra Strength Tar and Road Oil Remover B7A 19520 AA To avoid scratching the lamps do not use a dry paper towel chemical solvents or abrasive cleaners Cleaning the wiper blades windshield and rear window If the wiper blades do not wipe properly clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent To avoid damaging the blades do not use fuel kerosene paint thinner or other solvents If the wiper still does not wipe properly this could be caused by substances on the windshield or rear window such as tree sap and some hot wax treatments used by commercial car washes Clean the outside of the windshield or rear window with a non abrasive cleaner such as Ford 206 Maintenance and care Ultra Clear Spray Glass Cleaner E4AZ 19C507 AA available from your Ford Dealer Do not use abrasive cleansers on glass as they may cause scratches The windshield or rear window is clean if beads do not form when you rinse it with water The windshield rear window and wiper blades should be cleaned on a regular basis and blades or rubber elements replaced when worn Cleaning the instrument panel Clean with a damp cloth then dry with a dry cloth Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel The dull finish in this area helps protect the driver from undesirable win
180. t of your vehicle potentially including weight added to the cab the weight added should not exceed the front axle reserve capacity FARC Additional frontal weight may be added to the front axle reserve capacity provided you limit your payload in other ways i e restrict the number of passengers or amount of cargo carried You may add equipment throughout your vehicle if the total weight added is equal to or less than the total axle reserve capacity TARC weight You should NEVER exceed the total axle reserve capacity Always ensure that the weight of passengers cargo and equipment being carried is within the weight limitations that have been established for your vehicle including both gross vehicle weight and Front and rear gross axle weight rating limits Under no circumstance should these limitations be exceeded Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and or personal injury Special loading instructions for owners of pickup trucks and utility type vehicles For important information regarding safe operation of this type of vehicle see the Preparing to drive your vehicle section in the Driving chapter of this owner guide Loaded vehicles with a higher center of gravity may handle differently than unloaded vehicles Extra precautions such as slower speeds and increased stopping distance should be taken when driving a heavily loaded vehicle Your vehicle has the capability t
181. t seating positions 1 Do not install a child seat in a center facing jump seat Children and safety belts If the child is the proper size restrain the child in a safety seat Children who are too large for child safety seats as specified by your child safety seat manufacturer should always wear safety belts Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child s face or neck the child should wear the lap and shoulder belt Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit 93 Seating and safety restraints Do not leave children unreliable adults or pets unattended in your vehicle To improve the fit of lap and shoulder belts on children who have outgrown child safety seats Ford recommends use of a belt positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards Belt positioning booster seats raise the child and provide a shorter firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child A belt positioning booster should be used if the shoulder belt rests in front of the child s face or neck or if the lap belt does not fit snugly on both thighs or if the thighs are too short to let th
182. tance fuel delivery e towing of your disabled vehicle to the nearest Ford dealership or your selling dealer if within 25 kms 15 5 miles of the nearest Ford Dealership one tow per disablement Even non warranty related tows like accidents or getting stuck in the mud or snow are covered some exclusions apply such as impound towing or repossession Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference In the United States this card is found in the Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or Lincoln In Canada it is found in the Roadside Assistance book in the glove compartment To receive roadside assistance in the United States for Ford or Mercury vehicles call 1 800 241 3673 or if you own a Lincoln vehicle call 1 800 521 4140 In Canada call 1 800 665 2006 Should you need to arrange roadside assistance for yourself Ford will reimburse a reasonable amount To obtain information about reimbursement call 1 800 241 3673 in the United States for Ford or Mercury vehicles or if you own a Lincoln vehicle call 1 800 521 4140 Call 1 800 665 2006 in Canada 137 Roadside emergencies Roadside coverage beyond basic warranty In the United States you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury
183. tch pg 8 pg 19 Headlamp control pg 18 Turn signal and wiper washer control pg 61 Speed control pg 55 Driver air bag Parking brake release pg 84 pg 108 Instrumentation Awd control Electronic sound system ee point pg 119 pg 26 i Fog lamp control pg 18 Passenger air bag deactivate switch oe pg 88 Climate control system 19 ps 19 if equipped 7 Instrumentation WARNING LIGHTS AND CHIMES Standard instrument cluster lt FUEL DOOR Q g A a ENGINE SG lt FUEL DOOR Check engine Your vehicle is equipped with a computer that monitors the engine s CHECK emission control system This system is commonly known as the ENGINE On Board Diagnostics System OBD II This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards The OBD II system also assists the service technician in properly servicing your vehicle Instrumentation The Check Engine indicator light illuminates when the ignition is first turned to the ON position to check the bulb If it comes on after the engine is started one of the engine s emission control systems may be malfunctioning The light may illuminate without a driveability concern being not
184. te the SecuriLock system is protecting your vehicle e When the ignition is turned to RUN or START the theft indicator will light for three seconds and then go out If the theft indicator stays on for an extended period of time or flashes rapidly have the system serviced by your dealership or a qualified technician The Theft indicator is controlled by the SecwriLock system During the 30 second prearm state it is normal to see the theft indicator pulse brighter behind the constant glow Programming spare SecuriLock keys Spare SecuriLock keys can be purchased from your dealership and programmed to your SecuriLock passive anti theft system up to a total of eight keys Your dealership can program your new SecuriLock key s to your vehicle or you can do it yourself using the following simple procedure To program a new SecuriLock key yourself you will need two previously programmed SecuriLock keys keys that already operate your vehicle s engine If two previously programmed SecuriLock keys are not available one or both of your original keys were lost or stolen you must bring your vehicle to your dealership to have the spare SecuriLock key s programmed 68 Controls and features Procedure to program spare SecuriLock keys to your vehicle New SecuriLock keys must have the correct mechanical key cut for your vehicle Conventional non SecuriLock keys cannot be programmed to your vehicle Y
185. tes the maximum loaded weight that the vehicle is designed to tow Maximum Trailer Weight Rating Maximum weight of a trailer the vehicle is permitted to tow The maximum trailer weight rating is determined by subtracting the vehicle curb weight for each engine transmission combination any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle Maximum Trailer Weight Maximum weight of a trailer the loaded vehicle including passengers and cargo is permitted to tow It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle Trailer Weight Range Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating Remember to figure in the tongue load of your loaded trailer when figuring the total weight 125 Driving Do not exceed the GVWR or the GAWR specified on the certification label Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle s GVWR and GAWR limitations Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations The Certification Label found on the inside pillar of the driver s door lists several important vehicle weight rating limitations Before adding any additional equipment refer to these limitations If you are adding weight to the fron
186. the control to switch between AM FM1 or FM2 memory preset stations Tune adjust The tune control works in radio mode Tune adjust in radio mode e Press lt to move to the next frequency down the band whether or not a listenable station is located there Hold the control to move through the frequencies quickly e Press gt to move to the next frequency up the band whether or not a listenable station is located there Hold for quick movement Seek function The seek function control works in radio mode Seek function in radio mode e Press lt q to find the next listenable station down the frequency band e Press gt to find the next listenable station up the frequency band 27 Controls and features Radio station memory preset The radio is equipped with four station memory preset controls These controls can be used to select up to four preset AM stations and eight FM stations four in FM1 and four in FM2 Setting memory preset siations 1 Select the frequency band with the AM FM select control 2 Select a station Refer to Tune adjust or Seek function for more information on selecting a station 3 Press and hold a memory preset control until the sound returns indicating the station is held in memory on the control you selected ERIERER ED Bass adjust The bass adjust control allows you to increase or decrease the audio system s bass output Press the TONE control once then use the vo
187. the vehicle as soon as safely possible switch off C the engine immediately and let the engine cool Refer to Engine coolant in the Maintenance and care chapter Never remove the coolant reservoir cap while the engine is running or hot This gauge indicates the temperature of the engine coolant not the coolant level If the coolant is not at its proper level the gauge indication will not be accurate Tachometer if equipped Indicates the engine speed in revolutions per minute Driving with your tachometer pointer continuously at the top of the scale may damage the engine 15 Instrumentation Speedometer Indicates the current vehicle speed Odometer Registers the total kilometers miles of the vehicle Trip odometer Registers the kilometers miles of individual journeys To reset depress the control 16 oo omg 100 fe 1 120 i oo00000 oo omg 100 80 1 120 4 i I 000000 oo ogi 100 80 120 Instrumentation Engine oil pressure gauge This shows the engine oil pressure in the system Sufficient pressure exists as long as the needle remains in the normal range the area between the L and H H If the gauge indicates low pressure 7 uw stop the vehicle as soon as safely possible and switch off the engine a immediately Check the oil level Add oil if needed refer to Engine oil in th
188. this chapter If the engine coolant has not been checked at the recommended interval the engine coolant reservoir may become low or empty If the reservoir is low or empty add engine coolant to the reservoir Refer to Adding engine coolant in this chapter 169 Maintenance and care Automotive fluids are not interchangeable do not use engine coolant antifreeze or windshield washer fluid outside of its specified function and vehicle location Adding engine coolant Use only Ford Premium Engine Coolant E2FZ 19549 AA in Canada Motorcraft CXC 10 or a premium engine coolant that meets Ford specification ESE M97B44 A e DO NOT USE Ford Extended Life Engine Coolant F6AZ 19544 AA orange in color e DO NOT USE a DEX COOL engine coolant or an equivalent engine coolant that meets Ford specification WSS M97B44 D e DO NOT USE alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze e DO NOT USE supplemental coolant additives in your vehicle These additives may harm your engine s cooling system e DO NOT MIX recycled coolant and conventional coolant together in your vehicle Mixing of engine coolants may harm your engine s cooling system e The use of an improper coolant may harm engine and cooling system components and may void the warranty of your vehicle s engine cooling system If you are unsure which type of coolant your vehicle requires contact your local dealer Do not put
189. tom edge of the rear bumper Exceeding these limits may allow water to enter critical vehicle components adversely affecting driveability emissions reliability and causing internal transmission damage Replace the rear axle lubricant anytime the axle has been submerged in water Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair required Disconnect the wiring to the trailer before backing the trailer into the water Reconnect the wiring to the trailer after the trailer is removed from the water 135 Driving Recreational towing Follow these guidelines if you have a need for recreational towing An example of recreational towing would be towing your vehicle behind a motorhome These guidelines are designed to ensure that your transmission is not damaged 4x2 and 4x4 vehicles equipped with manual transmissions Before you have your vehicle towed e Release the parking brake e Move the gearshift to N Neutral e Turn the key in the ignition to the OFF UNLOCKED position e The maximum recommended speed is 88 km h 55 mph e The maximum recommended distance is unlimited In addition it is recommended that you follow the instructions provided by the after market manufacturer of the towing apparatus if one has been installed 4x2 and 4x4 vehicles equipped with automatic transmissions For all cars 4x2 truck sports utility with automatic transmissions or 4x4 truck sport uti
190. transmitters to your dealer for programming or e Perform the programming procedure yourself Programming remote transmitters It is necessary to have all maximum of four original and or new of your remote transmitters available prior to beginning this procedure To program the transmitters yourself e Insert a key in the ignition and turn from 3 OFF to 4 ON eight times in rapid succession within 10 seconds with the eighth turn ending in the 4 ON position The doors will lock unlock to confirm that programming mode has been entered e Within 20 seconds program a remote transmitter by pressing any button on a transmitter The doors will lock unlock to confirm that the remote transmitter has been programmed If more than 20 seconds pass before pressing a remote transmitter button the programming mode will exit and the procedure will have to be repeated e Repeat the previous step to program additional remote transmitters The doors will lock unlock to confirm that each remote transmitter has been programmed e When you have completed programming the remote transmitters turn the ignition to 3 OFF or wait 20 seconds Again the doors will lock unlock to confirm programming has been completed 66 Controls and features Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door s or sound the personal alarm The system automatically turns off after
191. trument Cluster Daytime Running Lights DRL RABS Resistor 20A Brake Pedal Position Switch 0 5 5 5 T System RABS Module 10A If equipped with 4 Wheel Anti Lock Brake System 4WABS Module 4WABS Main Relay 20A or 10A 20A If equipped with Rear Anti Lock Brake 7 5 Air Bag Indicator Lamp Alternator Indicator Lamp 30A Windshield Wiper Motor Wiper Hi Lo Relay Wiper Run Park Relay Cigar Lighter Data Link Connector DLC A 1 Driver s Unlock Relay All Unlock Relay All Lock Relay PCM Power Diode Ignition PATS 2 7 5A RAP Module Generic Electronic Module GEM Radio 142 1 2 3 4 5 7 10 11 12 13 14 15 16 17 18 19 0 Roadside emergencies Fuse Relay Fuse Amp Passenger Compartment Location Rating Fuse Panel Description Flasher Hazard Auxiliary Power Socket o o 2s CO Not Used Cid 24 7 5A Clutch Pedal Position CPP switch Starter Interrupt Relay Anti Theft P Not Used o 26 10A Battery Saver Relay Electronic Shift Relay Interior Lamp Relay Power Window Relay Electronic Shift Control Module Dome Map Lamp GEM Instrument Cluster Pet Not Used o PB Not eed o oo Not Used a J 33 15A Headlamps Daytime Running Lamps DRL Module Instrument Cluster o 34 CC Not Used p85 Not Used 36 Not Used 143 Roadside emergencies Power distribution box The power distribution box is located in the engine compartment The power distribution box co
192. ts 93 child safety belts 93 Child safety seats occ 94 attaching with tether straps 99 in front seat ssassn 96 in rear Seal ernearen eeii 96 tether anchorage hardware 99 Cleaning your vehicle 203 engine compartment 204 OXGETIOL sac Aciassecdecscseacsae 204 207 exterior laMPS sirosti 206 instrument panel c008 207 instrument panel lens 207 MAL ETIOR seer aar TEA 207 POET OLS vaese 208 Plastic parts wo eee 206 safety belts ccccecceeesseeees 207 WA SNINE serred EEA 203 WASTES 22 ccdcdactasGededarseenssndtecastocts 203 WELLS desserrer a 204 WINGOWS nruenang iiyaa 208 wiper blades cccsccceeerees 206 Index Climate control see Air conditioning or Heating 19 CIO CK seeur iei 29 36 42 51 Clutch Auld a 167 operation while driving 116 recommended shift speeds 118 CONSOIE aropin enerne euan naa 63 Coolant checking and adding 168 refill capacities 172 209 specifications e 212 214 Cruise control see Speed control 0 55 Customer Assistance 000 137 Ford accessories for your vehicle c 225 Ford Extended Service Plan wu 218 Getting assistance outside the U S and Canada cceeee 224 Getting roadside assistance 137 Getting the service you need s s s 218 Ordering additional owner s literature e
193. ur Wheel Drive vehicles 12 119 CONUTOL AC areri a 24 GESEHIPEION sarsies 119 driving off road 121 electronic shift 0 00 00 24 119 indicator light 2 0 0 eee 119 preparing to drive your vehicle irissen tinrin 110 PUG siscsseesiieiastsinestassvecsdlaseuresveiks 186 calculating fuel economy 192 CAD sce sendass Yon E A 188 Capacity x ee exiccdeahesttitecsaccdestag 209 choosing the right fuel 189 comparisons with EPA fuel economy estimates 195 detergent in fuel 191 filling your vehicle with fuel 0 186 188 192 filter specifications 192 209 fuel pump shut off switch 138 aD TOA EE E 14 improving fuel economy 192 octane rating sessie 190 214 215 UIALIGY resser onetyigheaneiansdecevvnd 190 running out of fuel 191 safety information relating to automotive fuels oo 186 FUSES iniiao 140 141 Gas cap see Fuel cap 188 Gas mileage see Fuel economy eses 192 GAUR ES ssstsscassdivenacsasthvdenecncays Gaceens 14 battery voltage gauge 17 engine coolant temperature gauge cecce 15 engine oil pressure gauge 17 fuel CAUSE erreien nn 14 OdomeEtET essaiera 16 speedometer ccccccceeeseeeees 16 tachometer ccccccceessseeesseees 15 CID OGOMELED cimeira 16 GAWR Gross Axle Weight Rating 125 Caleulating ssar 127 GETINIGION Sess2ssesacescesdechievusysxeec s 125 driving with
194. ur vehicle e The date of vehicle purchase e The current odometer reading e The vehicle identification number VIN If you still have a complaint involving a warranty dispute you may wish to contact the Dispute Settlement Board U S or the Mediation Arbitration Program Canada In some states in the U S you must directly notify Ford in writing before pursuing remedies under your state s warranty laws Ford is also allowed a final repair attempt in some states In the United States a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson Moss Warranty Act or to the extent allowed by state law before pursuing replacement or repurchase remedies provided by certain state laws This 220 Customer assistance dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson Moss Warranty Act or state replacement or repurchase laws THE DISPUTE SETTLEMENT BOARD U S only The Dispute Settlement Board is e an independent third party arbitration program for warranty disputes e available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states Ford Motor Company reserves the right to change eligibility limitations modify procedures and or to discontinue this service without notice and without incurring obligations per applicable
195. vehicle s engine The theft indicator will flash on and off Wait at least one minute and then repeat the procedure from step 1 If failure repeats bring your vehicle to your dealership to have the spare SecuriLock key s programmed 69 Seating and safety restraints SEATING Adjusting the front manual seat A Never adjust the driver s seat or seatback when the vehicle is moving A Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop A Always drive and ride with your seatback upright and the lap belt snug and low across the hips AN Reclining the seatback can reduce the effectiveness of the seat s safety belt in the event of a collision Lift handle to move seat forward or backward 70 Seating and safety restraints Pull lever up to adjust seatback Using the manual lumbar support if equipped Turn the lumbar support control clockwise to increase firmness A Turn the lumbar support control counterclockwise to increase I softness N REAR SEATS Center facing jump seat 2 door SuperCab if equipped To open pull inboard and down on the seat handle To stow the seat pull seat bottom back to the fully upright position A Do not install a child seat in a center facing jump seat 71 Seating and safety restraints Cenier facing jump seat 4 door SuperCab if equipped To open pull seat assembly down then raise seatback
196. vehicle and to its emissions system 195 Maintenance and care If other than Ford Motorcraft or Ford authorized parts are used for maintenance replacements or for service of components affecting emission control such non Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire Illumination of the Check Engine light charging system warning light or the temperature warning light fluid leaks strange odors smoke or loss of engine power could indicate that the emission control system is not working properly Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment Do not make any unauthorized changes to your vehicle or engine By law vehicle owners and anyone who manufactures repairs services sells leases trades vehicles or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working Information about your vehicle s emission system is on the Vehicle Emission Control Information Decal located on or near the engine This decal identifies engine displacement and gives some tune up specifications Please consult your Warranty Guide for complete emission warranty information Readiness
197. vehicle is started the transmission will automatically return to normal Overdrive mode 2 Second Use 2 Second to start up on slippery roads or to provide P RN D 21 additional engine braking on downgrades 1 First Use 1 First to provide maximum downgrades Upshifts can be made by shifting to 2 Second or to Overdrive Selecting 1 Low at higher speeds causes the transmission to shift to a lower gear and will shift to 1 First after the vehicle decelerates to the proper vehicle speed Forced Downshifits To gain acceleration in Overdrive or Drive O D OFF when passing another vehicle push the accelerator to the floor The transmission will downshift to the appropriate gear fourth third second or first gear Manual transmission operation if equipped Using the clutch Vehicles equipped with a manual transmission have a starter interlock that prevents Starting the engine unless the clutch pedal is fully depressed When starting a vehicle with a manual transmission 1 Hold down the brake pedal 2 Depress the clutch pedal 116 Driving 3 Put the gearshift lever in N Neutral 4 Start the engine and let it idle for a few seconds e Put the gearshift lever in 1 First or R Reverse 5 Release the clutch slowly while pressing gradually down on the accelerator pedal e Do not drive with your foot resting on the clutch pedal Do not use the clutch to hold your vehicle
198. weaker signal and play while the weak station frequency is displayed The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo Audio system warranties and service Refer to the Warranty Guide for audio system warranty information If service is necessary see your dealer or a qualified technician 53 Controls and features TURN SIGNAL CONTROL e Push down to activate the left turn signal e Push up to activate the right turn signal POSITIONS OF THE IGNITION 1 ACCESSORY allows the electrical p accessories such as the radio to operate while the engine is not running 3 2 LOCK locks the steering wheel 8 automatic transmission gearshift 2 lever and allows key removal 3 OFF shuts off the engine and all accessories without locking the steering wheel 4 ON all electrical circuits operational Warning lights illuminated Key position when driving 5 START cranks the engine Release the key as soon as the engine starts 54 Controls and features SPEED CONTROL IF EQUIPPED To turn speed control on e Press ON Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km h 80 mph Do not use the speed control in heavy traffic or on roads that are winding slippery or unpaved Do not shift the gearshift lever into N Neutral with the speed control on T
199. will be heard The tone pattern will repeat periodically until the problem and light are repaired 87 Seating and safety restraints If any of these things happen even intermittently have the SRS serviced at your dealership or by a qualified technician immediately Unless serviced the system may not function properly in the event of a collision Disposal of air bags and air bag equipped vehicles including pretensioners For disposal of air bags or air bag equipped vehicles see your local dealership or qualified technician Air bags MUST BE disposed of by qualified personnel Passenger air bag ON OFF switch An air bag ON OFF switch has been installed in this ON vehicle Before driving always look at the face of the switch to be sure the switch is in the proper OFF position in accordance with these instructions and warnings Failure PASSENGER AIRBAG to put the switch in a proper position can increase the risk of serious injury or death in a collision Turning the passenger air bag off 1 Insert the ignition key turn the switch to OFF position and hold in OFF position while removing the key 2 When the ignition is turned to the ON position the OFF light illuminates briefly momentarily PASSENGER AIRBAG shuts off and then turns back on This indicates that the passenger air bag is deactivated 88 Seating and safety restraints If the light fails to illuminate when the passenger air bag switc
200. with CD changer The shuffle feature operates in CD SHUFFLE changer mode only and plays all tracks on the current disc in random order The shuffle feature continues to the next disc after all tracks are played Press the SHUFFLE control to start this feature Random order play will continue until the SHUFFLE control is pressed again Setting the clock Press CLK to toggle between listening frequencies and clock mode while in radio mode To set the hour press and hold the CLK control and press the SEEK control lt A to decrease hours and e gt to increase hours To set the minute press and hold the CLK control and press the TUNE control 42 Controls and features e p to increase minutes Premium AM FM Siereo Cassette Single CD VOL PUSH ON v DSC y Ce OOMOOO Volume power control Press the control to turn the audio system on or off VOL PUSH ON Audio power can also be turned on by pressing the AM FM select control or the tape CD select control Audio power is turned off by using the volume power control 43 Controls and features Turn control to raise or lower VOL PUSH ON volume a N f y v If the volume is set above a certain level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition switch is turned back on AM FM select The AM
201. your vehicle If your vehicle is a flexible fuel vehicle FFV use only UNLEADED FUEL and ETHANOL 85 The use of leaded fuel is prohibited by law and could damage your vehicle Do not use fuel containing methanol It can damage critical fuel system components Your vehicle was not designed to use fuel or fuel additives with metallic compounds including manganese based compounds containing MMT Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty 189 Maintenance and care Octane recommendations Do not be concerned if your engine sometimes knocks lightly However if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating see your dealer or a qualified service technician to prevent any engine damage Unleaded Gasoline engines Your vehicle is designed to use Regular unleaded gasoline with an R M 2 octane rating of 87 We do not recommend the use of gasolines labeled as Regular that are sold with octane ratings of 86 or lower in high altitude areas FFV engine Your vehicle is designed to use Fuel Ethanol E85 Regular unleaded gasoline or any percentage of the two fuels combined U S government regulations require fuel ethanol dispensing pumps to have a small square orange and black label with the common abbreviation E85 or the appropriate percentage for that region Use of

Ford 2000 Ranger Automobile User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents