Home

Ford 1999 F-350 Automobile User Manual

1. Refer to Electronic Message Center for Trip A and Trip B features on the optional instrument cluster Engine coolant temperature gauge Indicates the temperature of the engine coolant At normal operating temperature the needle remains within the normal area the area between the H and C If it enters the red section the engine is overheating Stop the vehicle as soon as safely possible switch off the ignition and let it cool Refer to Engine coolant in the Maintenance and care chapter Never remove the coolant recovery cap while the engine is running or hot e Standard instrument cluster 18 Instrumentation e Optional instrument cluster This gauge indicates the temperature of the engine coolant not the coolant level If the coolant is not at its proper level the gauge indication will not be accurate If the gauge enters the red section the engine coolant and Check Engine Service Engine Soon indicators illuminate refer to What you should know about fail safe cooling in the Maintenance and care chapter Battery voltage gauge if equipped This shows the battery voltage when the ignition is in the ON position If the pointer moves and stays outside H the normal operating range as indicated have the vehicle s VOLTS electrical system checked as soon as possible L vy Engine oil pressure gauge if equipped This shows the engine
2. Turning the EATC off Press OFF The Outside Temperature function will continue to operate until the ignition is turned off AUTOMATIC Automatic operation Press AUTOMATIC and select the desired temperature The selected temperature and the word AUTO will appear in the display window The EATC system will either heat or cool to achieve the selected temperature The system will automatically determine fan speed airflow location and if outside air or recirculated air is required Fan speed remains automatic unless the fan speed thumbwheel is turned When in AUTOMATIC and weather conditions require heat air will be sent to the floor However if the engine is not warm enough to provide heat the fan will be at a low speed and the air will be directed to the windshield In 32 minutes or less the fan speed will start to increase and the airflow location will change to the floor area If unusual conditions exist i e window fogging etc the manual override controls allow you to select airflow locations and the fan control allows you to adjust fan speed as necessary Temperature selection The display window indicates the ar selected temperature function cic AUTO or one of the override AUTO controls and manual control of fan speed if automatic fan speed is not desired 29 Controls and features To control the temperature select any temperature between 18 C 65 F
3. lt SEEK p gt lt TUNE gt Volume power control Press the control to turn the audio system on or off S lt on See Turn the control to raise or lower volume x 35 Controls and features If the volume is set above a certain level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition switch is turned back on AM FM select The AM FM select control works in radio mode AM FM AM FM select in radio mode This control allows you to select AM or FM frequency bands Press the control to switch between AM FM1 or FM2 memory preset stations Tune adjust The tune control works in radio mode Tune adjust in radio mode e Press lt to move to the next frequency down the band whether or not a listenable station is located there Hold the control to move through the frequencies quickly e Press gt to move to the next frequency up the band whether or not a listenable station is located there Hold for quick movement Seek function The seek function control works in radio mode Seek function in radio mode e Press lt q to find the next listenable station down the frequency band e Press gt to find the next listenable station up the frequency band 36 Controls and features Radio station memory preset The radio is equipped with four station memory preset controls These controls can be used to sel
4. ccceeees 164 idle speed control 0008 170 lubrication specifications 201 208 refill capacities 0 0 0 200 SETVICE POINTS oo eee ees 155 starting after a collision 137 Engine block heater 119 Engime Oil 2 e345 dcscestuasicncses och 156 change oil soon warning message Center oe 156 checking and adding 156 GIDSTICKS sxeciseccsadetdessstsxRactncentetes 156 filter specifications 158 200 recommendations ccc 158 refill Capacities eee 200 specifications cee 201 203 Exhaust fumes cceceeeees 120 Fail safe cooling essersi 164 FIOOL Mats wo eeeeeeeeeceeeceeeesteeeeeeees 78 Fluid capacities ee 200 Pel ves s2eeciae eeaessaaste sS san ceasieientedos 178 calculating fuel economy 183 CAD E EE 180 CAPACIUY amp s secseesagncetdesaeencesest seas 200 choosing the right fuel 181 comparisons with EPA fuel economy estimates 00 186 detergent in fuel serseri 182 filling your vehicle with fuel oo 178 180 183 filter specifications 183 200 fuel pump shut off switch 137 GAUGE nomresi ra n n 15 improving fuel economy 183 low fuel warning light 8 octane rating 0 182 203 219 Index CALO EEU N i Mra NE E AE E 182 running out of fuel 182 safety information relating to automotive fuels 0 ee 178 FUSES siscsdessecesvendsacsssansoci
5. 50 Controls and features Turn the control to raise or lower K g gt volume VOL PUSH ON If the volume is set above a certain level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition switch is turned back on AM FM select The AM FM select control works in radio tape and CD modes if equipped AM FM select in radio mode This control allows you to select AM or FM frequency bands Press the control to switch between AM FM1 or FM2 memory preset stations AM FM select in tape mode Press this control to stop tape play and begin radio play AM FM select in CD mode Press this control to stop CD play and begin radio play Tune adjust The tune control works in radio or CD mode if equipped Tune adjust in radio mode E act ta whether or not a listenable station is located there Hold the control to move through the frequencies quickly e Press gt to move to the next frequency up the band whether or not a listenable station is located there Hold for quick movement Tune adjust for CD changer e Press lt A to select the previous disc in the CD changer Play will begin on the first track of the 51 Controls and features disc unless the CD changer is in shuffle mode Refer to Shuffle feature for more information Hold the control to continue reversing through the discs e Press B gt to select the next disc in the CD changer Hold th
6. 178 GIG grad s vevsssckcesccevenecacrnyes 175 WCAGDWEAR errereen R 175 TOMINE erson nenni esis 131 176 recreational towing 5 134 trailer tOWINY srecno 131 WYLOCKED crancut 152 Traction control eee 123 OM IGA cinese e aa 13 Traction lok rear axle 129 TYANSMISSION ssrsiisoniroiiessi 126 222 fluid checking and adding autoMatic 2 eee 167 fluid refill capacities 200 lubricant specifications 201 203 Trip Odometer cccccceseseeeeees 18 TUNK seran paienn n e R 89 remote release ssrsiceirr 75 82 Turn signal 4 seeyctss0y dyceeuasearsceese 11 63 Vehicle dimensions 0006 203 Vehicle Identification Number VIN ear aE 205 Vehicle loading c eee 129 Ventilating your vehicle 120 Warning chimes 0 ee 14 15 Warning lights see Lights 8 Washer fluid ccccceeeseeees 60 Water Driving through 135 Windows DOWD serea e e RAAS 19 Windshield washer fluid and wipers checking and adding fluid 160 checking and cleaning 173 OPETALLON rera nan ERER 63 replacing wiper blades 173 Wrecker towing oseese 152 223 Filling station information Engine oil capacity 4 7L 5 0 quarts Use Motorcraft SAE includes filter change 5W 30 Super Premium Motor Oil Ford specification WSS M2C153 G Tire pressure and size Refer to the Tire Pressure Label located on the r
7. 4 Using the disc holder release knob C pull the disc holder B out of the magazine 59 Controls and features If you pull too hard on the disc holder the disc holder may come completely out of the magazine If this happens reinsert the disc holder back into the magazine while pressing on the lever A 5 Line up the CD with the groove of the disc holder Ensure that the label on the CD faces downwards 6 Press in on the disc holder until it locks securely into the magazine If the disc holders are not fully locked into the magazine the unit will not operate Ensure that the disc holder is evenly inserted and at the same level as the magazine A The unit will not operate if the disc holder is not inserted at the same level B Radio power must be turned on to play the CDs in the changer The magazine may be stored in the glove box when not being used 60 Controls and features The CD magazine may be inserted or ejected with the radio power off ONLY use the magazine supplied with the CD changer other types will damage the unit Keep the CD changer door closed Coins and foreign objects will damage the CD player and void your audio system warranty Do not insert any promotional odd shaped or sized discs or discs with removable labels into the CD changer as that jamming may occur Troubleshooting the CD changer if equipped The laser beam used in the compact disc player is harmful to
8. 8 Install the plastic retainer and carefully push the carpet back in to place 191 Maintenance and care Replacing license plate lamp bulbs 1 Remove two screws grommets and the license plate lamp assembly from the trunk lid 2 Carefully pull the bulb from the socket and push in the new bulb 3 Install the lamp assembly on trunk lid with two grommets ensuring the grommets are pushed all the way in to the trunk lid and secure with two screws Replacing backup lamp bulbs 1 Open trunk and remove bulb socket from the trunk lid by turning counterclockwise 2 Pull the bulb straight out of the socket and push in the new bulb 3 Install the bulb socket in trunk lid by turning clockwise Replacing high mount brakelamp bulbs For bulb replacement see a dealer or qualified technician Replacing the interior bulbs Check the operation of the following interior bulbs frequently e interior overhead lamp e map lamp For bulb replacement see a dealer or qualified technician Using the right bulbs Replacement bulbs are specified in the chart below Headlamp bulbs must be marked with an authorized D O T for North America and an E for Europe to assure lamp performance light brightness and pattern and safe visibility The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time 192 Maintenance and care 222 AIMING THE HEADLAM
9. Main Light Switch Lighting Control Module Clock Police Power Relay Powertrain Control Module PCM Power Diode Ignition Coils A Lighting Control Module Power Mirrors PATS Module Keyless Entry Clock Memory Electronic Automatic Temperature Control HATC Power Windows Police Spot Light SecuriLock 7 pt aE PA 5 15A Backup Lamps Variable Assist Power Steering VAPS Turn Signals Air Suspension Daytime Running Lamps Electronic Day Night Mirror Shift Lock EATC Speed Chime Warning SS EEE 140 Roadside emergencies Fuse Relay Fuse Amp Passenger Compartment Location soon Fuse Panel Description Blower Motor A C Heater Mode Switch a Air Bag Module 5A Radio S 18A CB Lighting Control Module Flash to Pass Main Light Switch 20A CB Window Door Lock Control Driver s Door Module One Touch Down Anti Lock Brakes Instrument Cluster Transmission Control Switch a Cigar Lighter Auxiliary Power Point Air Bag Module Warning Lamps Analog Cluster Gauges and Indicators Electronic Automatic Transmission Lighting Control Module Power distribution box The power distribution box is located in the engine compartment The power distribution box contains high current fuses that protect your vehicle s main electrical systems from overloads Always disconnect the battery before servicing high current fuses Always replace the cover to the Power Distribution Box before reconnecting the b
10. Never remove the coolant reservoir cap while the engine is running or hot 5 Re start the engine and take your vehicle to a service facility Driving the vehicle without repairing the engine problem increases the chance of engine damage Take your vehicle to a service facility as soon as possible 166 Maintenance and care CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid Refer to the Scheduled Maintenance Guide for the service interval schedules If adding fluid is necessary use only MERCON ATF 1 Start the engine and let it run until it reaches normal operating temperature the engine coolant temperature gauge indicator will be near the center of the normal area between H and C 2 While the engine idles turn the steering wheel left and right several times 3 Turn the engine off 4 Check the fluid level in the reservoir It should be between the MIN and MAX lines Do not add fluid if the level is in this range 5 If the fluid is low add fluid in small amounts continuously checking the level until it reaches the range between the MIN and MAX lines Be sure to put the cap back on the reservoir TRANSMISSION FLUID Checking automatic transmission fluid Refer to your Scheduled Maintenance Guide for scheduled intervals for fluid checks and changes Your transmission does not consume fluid However the fluid level should be checked if the transmission is not working properl
11. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you the driver You must gather information as accurately and consistently as possible Fuel expense frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy We do not recommend taking fuel economy measurements during the first 1 600 km 1 000 miles of driving engine break in period You will get a more accurate measurement after 3 000 km 5 000 km 2 000 miles 3 000 miles Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill Capacities section of the Capacities and specifications chapter The advertised capacity is the amount of the indicated capacity and the empty reserve combined Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty Empty reserve is the small amount of usable fuel remaining in the fuel tank after the fuel gauge indicates empty The amount of empty reserve varies and should not be relied upon to increase driving range When refueling your vehicle after the fuel gauge indicates empty you might not be able to refuel the full amount of the advertised capacity of the fuel tank due
12. assist will decrease to improve steering feel At lower speeds maneuverability will be increased If the amount of effort required to steer your vehicle changes at a constant vehicle speed have the power steering system checked by your dealer or a qualified service technician AIR SUSPENSION SYSTEM IF EQUIPPED The air suspension system is designed to improve ride handling and general vehicle performance during e certain road conditions e steering maneuvers e braking accelerations 125 Driving This system keeps the rear of your vehicle at a constant level by automatically adding air or releasing air from the springs If you exceed the load limit the rear air suspension may not operate The air suspension shut off switch is located on the left side of the trunk If this switch is in the OFF position the rear air suspension will not operate On vehicles equipped with Air Suspension turn OFF the Air Suspension switch prior to jacking hoisting or towing your vehicle Normal vehicle operation does not require any action by the driver AUTOMATIC TRANSMISSION OPERATION i Brake shift interlock AIR SUSPENSION SWITCH INTERRUPTEUR DE LA SUSPENSION PNEUMATIQUE WARNING To prevent sudden vehicle movement turn off air suspen sion switch prior to jacking hoisting or towing vehicle AVERTISSEMENT Pour pr venir tout mouvement soudain du v hi cule placer a l arr t l inte
13. increments through the filler tube until the level is correct If an overfill occurs excess fluid should be removed by a qualified technician An overfill condition of transmission fluid may cause shift and or engagement concerns and or possible damage 169 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance free battery which normally does not require additional water during its life of service However for severe usage or in high temperature climates check the battery electrolyte level Refer to the Scheduled Maintenance Guide for the service interval schedules Keep the electrolyte level in each cell up to the level indicator Do not overfill the battery cells If the electrolyte level in the battery is low you can add plain tap water to the battery as long as you do not use hard water water with a high mineral or alkali content If possible however try to only fill the battery cells with distilled water If the battery needs water often have the charging system checked If your battery has a cover shield make sure it is reinstalled after the battery has been cleaned or replaced For longer trouble free operation keep the top of the battery clean and dry Also make certain the battery cables are always tightly fastened to the battery terminals If you see any corrosion on the battery or terminals remove the cables from the terminals and clean with a wire bru
14. pedal gradually as the engine speeds up 5 After idling for a few seconds apply the brake and release the parking brake Using the engine block heater if equipped An engine block heater warms the engine coolant which improves starting warms up the engine faster and allows the heater defroster system to respond quickly Use of an engine block heater is strongly recommended if you live in a region where temperatures reach 23 C 10 F or below For best results plug the heater in at least three hours before starting the vehicle Using the heater for longer than three hours will not harm the engine so the heater can be plugged in the night before starting the vehicle To prevent electrical shock do not use your heater with ungrounded electrical systems or two pronged cheater adapters 119 Starting Guarding against exhaust fumes Although odorless and colorless carbon monoxide is present in exhaust fumes Take precautions to avoid its dangerous effects If you ever smell exhaust fumes of any kind inside your vehicle have your dealer inspect and fix your vehicle immediately Do not drive if you smell exhaust fumes These fumes are harmful and could kill you Have the exhaust and body ventilation systems checked whenever e the vehicle is raised for service e the sound of the exhaust system changes e the vehicle has been damaged in a collision Engine exhaust some of its constituents and certain vehicle compone
15. 7L 5 0 quarts Oil Brake fluid ill to line on reservoir Power steering fluid Motorcraft MERCON Fill to line on reservoir ATF Transmission fluid Motorcraft 3 Engine coolant Premium Engine Coolant 15 0L 15 8 quarts 71 9L 19 0 gallons Rear axle lubricant Motorcraft SAE 80W 90 Premium Rear 1 8L 8 75 pints Axle Lubricant fluid Washer Concentrate 1 Use only brake fluids certified to meet Ford specifications Refer to Lubricant Specifications in this chapter DOT 3 fluid is recommended However if DOT 3 is not available DOT 4 fluid can be used 200 Capacities and specifications 2 Ensure the correct automatic transmission fluid is used MERCON and MERCON V are not interchangeable DO NOT MIX MERCON and MERCON V Refer to the Scheduled Maintenance Guide to determine the correct service interval 3 Indicates only approximate dry fill capacity Some applications may vary based on cooler size and if equipped with an in tank cooler The amount of transmission fluid and fluid level should be set by the indication on the dipstick s normal operating range Police Package refill capacity 12 1L 12 8 quarts 4 Use Ford Premium Engine Coolant green in color DO NOT USE Ford Extended Life Engine Coolant orange in color Refer to Adding engine coolant in the Maintenance and Care chapter 5 Rear axles are considered lubricated for life when the vehicle is used for normal service See yo
16. A DATE XXXXX FGAWR XXXXXX XXXXXXX GVWR XXXXX LB XXXXX KG RGAWR XXXXXXX XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE VIN XXXXXXXXXXXXXXXXX TYPE XXXXXXXXXXXXXXX MAXIMUM LOAD OCCUPANTS LUGGAGE XXXKG XXXXLB OCCUPANTS X TOTAL X FR X 2N TIRE XXXX XXXXX XXX PRESSURE FR XXX kPa 33 PSI PRESSURE RR XXX kPa 33 PS TRAILER TOWING SEE OWNER GUIDE D X RR OCCUPANTS LUGGAGE XX XXXKG XXXXLB X XXXKG XXXXLB COLD COLD EXT PNT XXXXXX XXXXXX_ RC XX DSO XXXX_ F000 R SPR T0000 BAR INTTR TP PS R JAXLE X XX XXX X XX X XXXX UTC VFOHT 15294A10 GA Vehicle identification number The vehicle identification number is attached to a metal tag and is Capacities and specifications located on the driver side instrument panel Please note that es in the graphic XXXX is representative of your vehicle Sr identification number N SS Engine number The engine number the last eight numbers of the vehicle identification number is stamped on the engine block transmission frame and transfer case if equipped 205 Customer assistance Ford Extended Service Plan You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan Ford ESP coverage Ford ESP is an optional service contract which is backed by Ford Motor Company
17. Belt Minder sscspirriirrinsieia 101 218 Brakes ser coasters dats eb sases AEE 121 anti lock eeren 121 122 anti lock brake system ABS warning light 11 122 brake warning light 11 fluid checking and adding 159 fluid refill capacities 200 fluid specifications 201 203 lubricant specifications 201 203 shift interlock cceeees 126 Break in period cccccceeceeeeeeees 3 Capacities for refilling fluids 200 Cassette tape player c 50 CD Changer 0 3 ico ssecestssieacencansdetec 59 Certification Label 05 204 Child safety restraints 110 child safety belts 110 Child safety seats wc 111 attaching with tether straps 115 iy TONE SEAL agape 112 IN TEAL Seat sevcsvessersocevssness 112 115 Cleaning your vehicle 193 engine compartment 196 EXUCTIOF mocnin a 195 exterior lamps ccceeeeeees 195 instrument panel isoen 197 instrument panel lens 198 INCETIOR esiesscieetistiiedderncdecss 198 199 POULT OLS sexi eciccesiasidertvesseleacativeces 195 plastic OATS sereparenerssiemss 195 Safety belts ccccceceeeeseeees 198 WASHING seese rD 194 WAKING ar AO 194 wheel aenn 195 WINDOWS sendaren E a 198 wiper blades cccceeeeeeeeees 196 woodtone trim 0 eee 198 Climate control see Air conditioning or Heating 26 CIO os cccsiteecazs
18. COOL engine coolant or an equivalent engine coolant that meets Ford specification WSS M97B44 D e DO NOT USE alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze e DO NOT USE supplemental coolant additives in your vehicle These additives may harm your engine s cooling system e DO NOT MIX recycled coolant and conventional coolant together in your vehicle Mixing of engine coolants may harm your engine s cooling system e The use of an improper coolant may harm engine and cooling system components and may void the warranty of your vehicle s engine cooling system If you are unsure which type of coolant your vehicle requires contact your local dealer Do not put engine coolant in the windshield washer fluid reservoir If engine coolant is sprayed onto the windshield it could make it difficult to see through the windshield When the engine is cool add a 50 50 mixture of engine coolant and distilled water to the engine coolant reservoir until the coolant is at the cold fill level or within the cold fill range as listed in the engine coolant reservoir depending upon application e NEVER increase the coolant concentration above 60 e NEVER decrease the coolant concentration below 40 e Engine coolant concentrations above 60 or below 40 will decrease the freeze protection characteristics of the engine coolant and may cause engine damage Plain water may be added in
19. If you do not use the proper fuel filler cap excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel system to work improperly in a collision which may result in possible personal injury Automotive fuels can cause serious injury or death if misused or mishandled Gasoline may contain benzene which is a cancer causing agent Observe the following guidelines when handling automotive fuel e Extinguish all smoking materials and any open flames before fueling your vehicle e Always turn off the vehicle before fueling e Automotive fuels can be harmful or fatal if swallowed Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury If fuel is swallowed call a physician immediately even if no symptoms are immediately apparent The toxic effects of fuel may not be visible for hours e Avoid inhaling fuel vapors Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation In severe cases excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury 179 Maintenance and care Avoid getting fuel liquid in your eyes If fuel is splashed in the eyes remove contact lenses if worn flush with water for 15 minutes and seek medical attention Failure to seek proper medical attention could lead to permanent injury Fuels can also be harmful if absorbed through the skin If fuel is splashed on
20. MIRROR IF EQUIPPED Your vehicle is equipped with an inside rear view mirror which has an auto dimming function The electronic day night mirror will change from the normal state to the non glare state when bright lights glare reach the mirror When the mirror detects bright light from front or behind it will automatically adjust darken to minimize glare Do not block the sensor on the backside of the mirror since this may impair proper mirror performance Press the control to turn the mirror on or off The mirror will automatically return to the normal state whenever the vehicle is placed in R Reverse when the mirror is on to ensure a bright clear view when backing up ELECTRONIC COMPASS IF EQUIPPED The compass reading will remain accurate during most driving conditions Unknown to the driver the compass is continuously recalibrating due to magnetic fields and subtle slow changes in vehicle magnetics which can occur over the life of the vehicle The compass reading will remain fixed when significant levels are experienced such as steel bridges The compass will return to normal operation upon leaving the magnetized area If highly magnetized items such as magnetic mount antennas are placed very near the compass the display will change to C for 15 seconds then display all segments until the magnetized item is removed If a C is displayed refer to Compass calibration adjustment Most ge
21. New Vehicle Limited Warranty period U S of three years or 60 000 km 86 000 miles whichever comes first on Ford and Mercury vehicles and four years or 80 000 km 50 000 miles on Lincoln vehicles Roadside assistance will cover e changing a flat tire jump starts lock out assistance fuel delivery towing to the nearest Ford of Canada or Ford Motor Company dealership or towing to your selling dealership if within 56 km 85 miles Even non warranty related tows like accidents or getting stuck in the mud or snow are covered some exclusions apply such as impound towing or repossession Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference In the United States this card is found in the Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or Lincoln In Canada it is found in the Roadside Assistance book in the glove compartment To receive roadside assistance in the United States for Ford or Mercury vehicles call 1 800 241 3673 or if you own a Lincoln vehicle call 1 800 521 4140 In Canada call 1 800 665 2006 Should you need to arrange roadside assistance for yourself Ford will reimburse a reasonable amount To obtain information about reimbursement call 1 800 241 3673 in the United States for Ford or Mercury vehicles or if you own a Lincoln vehicle call 1 800 521 4140 Call 1 800 665 2006 in
22. a collision should also be inspected and replaced if either damage or improper operation is noted Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision Refer to Cleaning and maintaining the safety belts in the Maintenance and care section 104 Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM SRS C Your vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity This information will assist Ford in the servicing of your vehicle and may help Ford better understand real world collisions and further improve the safety of future vehicles Important supplemental restraint system SRS precautions The supplemental restraint system N is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module All occupants of the vehicle including the driver should always properly wear the
23. airflow to the back seats e Remove any snow ice or leaves from the air intake area at the bottom of the windshield e If your vehicle has been parked with the windows closed during hot weather the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open This will force most of the hot stale air out of the vehicle Then operate your air conditioner as you would normally e Do not place objects over the defroster outlets These objects can block airflow and reduce your ability to see through your windshield Also avoid placing small objects on top of your instrument panel These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop Electronic Automatic Temperature Control EATC system if equipped The EATC system will maintain a selected temperature and automatically control airflow You 3 can override automatic operation re maa an a a oer E with any of the override controls or the fan speed control OFF F UZ auto OUTSIDE TEMP automate ES baa ea Ba 28 Controls and features Turning the EATC on Press AUTOMATIC any of the override controls or the fan speed control The EATC will only operate when the vehicle is running
24. an emergency but you must replace it with a 50 50 mixture of engine coolant and distilled water as soon as possible Check the coolant level in the reservoir before you drive your vehicle the next few times with the engine cool If necessary add a 50 50 mixture of engine coolant and distilled water to the engine coolant reservoir until the coolant level is at the cold fill level or within the cold fill range as listed on the reservoir depending upon application 162 Maintenance and care Have your dealer check the engine cooling system for leaks if you have to add more than 1 0 liter 1 0 quart of engine coolant per month To avoid scalding hot steam or coolant from being released from the engine cooling system never remove the radiator cap while the engine is running or hot Failure to follow this warning may result in damage to the engine s cooling system and possible severe personal injury If you must remove the radiator cap follow these steps to avoid personal injury 1 Before you remove the cap turn the engine off and let it cool 2 When the engine is cool wrap a thick cloth around the cap Slowly turn cap counterclockwise until pressure begins to release 3 Step back while the pressure releases 4 When you are sure that all the pressure has been released use the cloth to turn it counterclockwise and remove the cap Recycled engine coolant Ford Motor Company recommends the use of a recycled engine
25. and 29 C 85 F by pressing the blue cooler or red warmer buttons OUTSIDE TEMP For continuous maximum cooling push the blue button until 16 C 60 F is shown in the display window The EATC will continue maximum cooling disregarding the displayed temperature until a warmer temperature is selected by pressing the red button For continuous maximum heating push the red button until 32 C 90 F is shown in the display window The EATC will continue maximum heating disregarding the displayed temperature until a cooler temperature is selected by pressing the blue button Temperature conversion Press MAX A C and DEF Q at the same time for one second to Se i a AUTOMATIC switch between Fahrenheit and Celsius EA f C Cron E E If your vehicle has an English Metric E M control to change your electronic instrument cluster display if equipped and the message center display Gf equipped from English to Metric this control will also change the temperature display Refer to Electronic Message Center in the Instrumentation Chapter 30 Controls and features Fan speed 8 When AUTOMATIC is pressed fan speed is adjusted automatically for existing conditions You can override a fan speed at any time To control fan speed manually use the thumbwheel to cancel automatic fan speed operation Rotate the thumbwheel up for higher fan speed or down for
26. and Lincoln Mercury dealership management recognized for their business leadership qualities What the Board needs To have your case reviewed you must complete the application in the DSB brochure and mail it to the address provided on the application form Some states will require you to use certified mail with return receipt requested Your application is reviewed and if it is determined to be eligible you will receive an acknowledgment indicating e the file number assigned to your application e the toll free phone number of the DSB s independent administrator Your dealership and a Ford Motor Company representative will then be asked to submit statements To properly review your case the Board needs the following information e legible copies of all documents and maintenance or repair orders relevant to the case e the year make model and Vehicle Identification Number VIN listed on your vehicle ownership license e the date of repair s and mileage at the time of occurrence s e the current mileage e the name of the dealer s who sold or serviced the vehicle e a brief description of your unresolved concern e a brief summary of the action taken by the dealer s and Ford Motor Company 210 Customer assistance e the names if known of all the people you contacted at the dealership s e a description of the action you expect to resolve your concern You will receive a letter of explanation if your applicati
27. and sound a tone for one second then remain on if the trunk is open Safety belt warning chime A CHECK AIR SUSPENSION DOOR OVERDRIVE OFF AJAR tow 4 YU om ru S A IU ear TRUNK AJAR LTR 100 km CHECK AIR SUSPENSION DOOR OVERDRIVE OFF AJAR eine BER Yt TRUNK AJAR LTR 100 km CHECK AIR SUSPENSION DOOR OVERDRIVE OFF AJAR ai i mt Mi i WASHER MILES FLUID J E PA A GAL TRUNK AJAR LTR 100 km Sounds to remind you to fasten your safety belts For information on the safety belt warning chime refer to the Seating and safety restraints chapter Supplemental restraint system SRS warning chime at For information on the SRS warning chime refer to the Seating and safety restraints chapter Key in ignition warning chime Sounds when the key is left in the ignition in the OFF LOCK or ACC position and the driver s door is opened 14 Instrumentation Headlamps on warning chime Sounds when the headlamps or parking lamps are on the ignition is off and the key is not in the ignition and the driver s door is opened GAUGES Standard instrument cluster gauges TRAC LOW CHECK CNTL FUEL ENGINE A CHECK CHECK AIR SUSPENSION DOOR A ENGINE OVERDRIVE OFF AJAR F tow DL la AR uD L eat TRUNK AJAR LTR 100 km TO EMPTY ECONOMY TRIP I TRIP I AVG A B SPEED PRNO21 Fuel gauge Displays approximately how much fuel is in the fuel tank when the key is in t
28. applicable written new vehicle warranty are eligible for review except those involving e anon Ford product e anon Ford dealership e sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle s performance as designed e a request for reimbursement of consequential expenses unless a service or product concern is being reviewed e items not covered by the New Vehicle Limited Warranty including maintenance and wear items e alleged personal injury property damage claims e cases currently in litigation e vehicles not used primarily for family personal or household purposes except in states where the Dispute Settlement Board is required to review commercial vehicles e vehicles with non U S warranties Concerns are ineligible for review if the New Vehicle Limited Warranty has expired at receipt of your application and in certain states eligibility is dependent upon the customer s possession of the vehicle 209 Customer assistance Eligibility may differ according to state law For example see the unique brochures for California West Virginia Georgia and Wisconsin purchasers lessees Board membership The Board consists of e three consumer representatives e a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm The dealership Board member is chosen from Ford
29. brings soft and loud CD passages together for a more consistent listening level Press the COMP control to activate and deactivate compression adjust The effect of the feature varies with the music content Shuffle feature The shuffle feature operates in CD mode and plays all tracks on the SHUFF current disc in random order If equipped with the CD changer the of 56 Controls and features shuffle feature continues to the next disc after all tracks are played Press the SHUFFLE control to start this feature Random order play will continue until the SHUFFLE control is pressed again Mute mode Press the control to mute the playing media Press the control again to return to the playing media Radio data system RDS feature This feature allows your audio system to receive station identification or program type from RDS equipped FM radio stations C N ee RDS The Federal Communications Commission FCC and the Canadian Radio and Telecommunications Commission CRTC recommend FM radio broadcasters to use RDS technology to transmit information FM radio stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired Press and hold the control for five seconds to turn the feature on or off Press the control to scroll through the following selections Traffic e Press the RDS control until TRAFFIC is displayed RDS e Use
30. came with your vehicle Insert and twist the handle then pry against the wheel 144 Roadside emergencies 5 Loosen each wheel lug nut one half turn counterclockwise but do not remove them until the wheel is raised off the ground Refer to Anti theft lug nuts for information on removing anti theft lug nuts On vehicles equipped with z AIR SUSPENSION Air Suspension turn OFF SWITCH the Air Suspension switch prior to INTERRUPTEUR DE jacking hoisting or towing your LA SUSPENSION PNEUMATIQUE WARNING To prevent sudden vehicle movement turn off air suspen sion switch prior to jacking hoisting or towing vehicle AVERTISSEMENT Pour pr venir tout mouvement soudain du v hi cule placer l arr t l interrupteur de la suspension pneumatique avant de lever to v hicule cric ou pont l vateur ou de le remorquer vehicle Refer to Atr suspension system in the Driving chapter for more information OFF ARRET Jacking notches are located approximately six inches rearward of the front wheels and twelve inches foward of the rear wheels 6 Locate the jack notch closest to the tire you are changing then place the jack under the frame of the vehicle aligning it with the notch T Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground 145 Roadside emergencies To lessen the
31. clear ice or fog from the windshield If the outside air temperature is about 10 C 50 F or higher the air conditioner will automatically dehumidify the air to reduce fogging OFF Outside air is shut out and the fan will not operate For short periods of time use this mode to reduce undesirable odors from entering the vehicle 32 Controls and features Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature It will be displayed until OUTSIDE TEMP is pressed again ae ne Co If the selected temperature is changed while the outside temperature is displayed the new temperature will be displayed for four seconds after it is changed then the outside temperature will return to the window If a manual override function is selected while the outside temperature is displayed the new function will be displayed for four seconds after it is changed then the outside temperature will return to the window along with the override selection The outside temperature reading is most accurate when the vehicle is moving Higher readings may be obtained when the vehicle is not moving The readings that you get may not agree with temperatures given on the radio due to differences in vehicle and station locations Operating tips e In humid weather select DEF Q before driving This will reduce fogging on your windshield After a few minutes select any desired position To prevent humidity bu
32. corrosion e an accurate temperature readout from the engine coolant gauge The engine coolant must be maintained at the correct fluid level and concentration to work properly If the engine coolant fluid level and concentration is not maintained correctly damage to the engine and cooling system may result When the engine is cold check the level of the engine coolant in the reservoir e The engine coolant should be at the cold fill level or within the cold fill range as listed on the engine coolant reservoir depending upon application e Refer to the Scheduled Maintenance Guide for service interval schedules e Be sure to read and understand Precautions when servicing your vehicle in this chapter If the engine coolant has not been checked at the recommended interval the engine coolant reservoir may become low or empty If the reservoir is low or empty add engine coolant to the reservoir Refer to Adding engine coolant in this chapter Automotive fluids are not interchangeable do not use engine coolant antifreeze or windshield washer fluid outside of its specified function and vehicle location Adding engine coolant Use only Ford Premium Engine Coolant E2FZ 19549 AA in Canada Motorcraft CXC 10 or a premium engine coolant that meets Ford specification ESE M97B44 A 161 Maintenance and care e DO NOT USE Ford Extended Life Engine Coolant F6AZ 19544 AA orange in color e DO NOT USE a DEX
33. designed for emergency use only Replace this tire with a full size tire as soon as possible If you use the temporary spare tire continuously or do not follow these precautions the tire could fail causing you to lose control of the vehicle possibly injuring yourself or others 143 Roadside emergencies When driving with the temporary spare tire do not e exceed 80 km h 50 mph under any circumstances e load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label e tow a trailer e use tire chains drive through an automatic car wash because of the vehicle s reduced ground clearance try to repair the temporary spare tire or remove it from its wheel e use the wheel for any other type of vehicle Tire change procedure To prevent the vehicle from moving when you change a tire be sure the parking brake is set then block Gin both directions the wheel that is diagonally opposite other side and end of the vehicle to the tire being changed If the vehicle slips off the jack you or someone else could be seriously injured 1 Park on a level surface activate hazard flashers and set parking brake 2 Place gearshift lever in P Park and turn engine OFF 3 Remove the spare tire and the jack and lug wrench which are under the spare tire 4 Locate pry off notch if equipped and remove the center ornament from the aluminum wheel with the tapered end of the wheel nut wrench that
34. dipstick and the ambient temperature is above 10 C 50 F Correct fluid level The transmission fluid should be checked at normal operating temperature 66 C 77 C 150 F 170 F on a level surface The normal operating temperature can be reached after approximately 30 km 20 miles of driving You can check the fluid without driving if the ambient temperature is above 10 C 50 F However if fluid is added at this time an overfill condition could result when the vehicle reaches normal operating temperature 168 Maintenance and care The transmission fluid should be in this range if at normal operating temperature 66 C 77 C 150 F 170 F The transmission fluid should be in this range if at ambient temperature 10 C 35 C 50 F 95 F High fluid level Fluid levels above the safe range may result in transmission failure An overfill condition of transmission fluid may cause shift and or engagement concerns and or possible damage High fluid levels can be caused by an overheating condition Adjusting automatic transmission fluid levels Before adding any fluid make sure the correct type is used The type of fluid used is normally indicated on the dipstick and also in the Lubricant specifications section in the Capacities and specifications chapter Use of a non approved automatic transmission fluid may cause internal transmission component damage If necessary add fluid in 250 mL 1 2 pint
35. find the next listenable station up the frequency band Scan function The scan function works in radio mode Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band Press the SCAN control again to stop the scan mode Radio station memory preset The radio is equipped with six station memory preset controls These controls can be used to select up to six preset AM stations and twelve FM stations six in FM1 and six in FM2 40 Controls and features Setting memory preset siations 1 Select the frequency band with the AM or the FM select control 2 Select a station Refer to Tune adjust or Seek function for more information on selecting a station 3 Press and hold a memory preset control until the sound returns indicating the station is held in memory on the control you selected VOOM Bass adjust The bass adjust control allows you i to increase or decrease the audio A system s bass output BASS ae Treble adjust The treble adjust control allows you to increase or decrease the audio A system s treble output TREB 41 Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the right and left A speakers BAL as Speaker fade adjust Speaker sound can be adjusted between the front and rear A speakers FADE y Tape select e To enter tape m
36. flash after 20 seconds Release both buttons 2 Hold the end of your hand held transmitter 5 14 cm 2 5 inches V away from the HomeLink Universal Transceiver surface located on your visor while keeping the red light in view 3 Using both hands simultaneously press and hold the hand held transmitter button and the desired ay HomeLink button Do not release the buttons until step 4 has been completed Some entry gates and garage door openers may require you to replace step 3 with the procedure in the Canadian Programing section 4 The red light will flash slowly and then rapidly Release both buttons when the red light flashes rapidly 5 Follow steps 2 through 4 to program the remaining two buttons If you do not successfully program the HomeLink Universal Transceiver after repeated attempts refer to Rolling code programing which follows or call toll free customer assistance 1 800 355 3515 or on the Internet at HomeLink jci com Canadian Programming During programming your hand held transmitter may automatically stop transmitting after two seconds which may not be long enough to program the HomeLink Universal Transceiver 70 Controls and features To program your hand held transmitters e continue to hold the button on 1th the HomeLink Universal O O Transceiver press and re press the hand held transmitter button every two seconds until the red light changes from a
37. further check for leaks in the fuel system FUSES AND RELAYS Fuses If electrical components in the vehicle are not working a fuse may have blown Blown fuses are identified by a broken wire within the fuse Check the appropriate 15 fuses before replacing any electrical components 138 Roadside emergencies Always replace a fuse with one that has the specified amperage rating Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire Standard fuse amperage rating and color Fuse Mini i ase ara Fuse Link Rating Fuses Cartridge 24 ae aer ee J 3A Voet Videt Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal Remove the panel cover to access the fuses To remove a fuse use the fuse puller tool provided on the fuse panel cover 139 Roadside emergencies The fuses are coded as follows Fuse Relay Fuse Amp Passenger Compartment Location Rating Fuse Panel Description 1 Brake Pedal Position BPP Switch Multi Function Switch Speed Control Wiper Control Module Windshield Wiper Motor 3 Not Used 15 2 0 4 5 Lighting Control Module Main Light Switch 5 5 5 15 Speed Control
38. hold the key 0 square to the lug nut If you hold v the key at an angle you could damage the key and the lug nut 2 Place the lug nut wrench over the lug nut key and apply pressure on the key with the wrench 3 Turn the wrench in a counterclockwise direction to remove the lug nut To install the anti theft lug nut 1 Insert the key over the locking lug nut 2 Place the lug nut wrench over the lug nut key and apply pressure on the key with the wrench 3 Install the lug nut JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames sparks or lit cigarettes An explosion could result in injury or vehicle damage Do not push start your vehicle You could damage the catalytic converter Batteries contain sulfuric acid which can burn skin eyes and clothing if contacted Do not attempt to push start your vehicle Automatic transmissions do not have push start capability Preparing your vehicle 1 Use only a 12 volt supply to start your vehicle 2 Do not disconnect the battery of the disabled vehicle as this could damage the vehicle s electrical system 147 Roadside emergencies 3 Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts 4 Check all battery terminals and remove any excessive corrosion before you at
39. inside the luggage compartment Adults are advised to familiarize themselves with the operation and location of the release handle To open the luggage compartment door lid from the inside pull the illuminated T shaped handle and push up on the trunk lid The material that the handle is made of will glow for hours in the darkness of the luggage compartment following brief exposure to ambient light The T shaped handle will be located either on the luggage compartment door lid or inside the luggage compartment near the tail lamps 89 Controls and features Keep vehicle doors and luggage compartment locked and keep keys out of a child s reach Unsupervised children could lock themselves in an open trunk and risk injury Children should be taught not to play in vehicles On hot days the temperature in the trunk or vehicle interior can rise very quickly Exposure of people or animals to these high temperatures for even a short time can cause death or serious heat related injuries including brain damage Small children are particularly at risk 90 Seating and safety restraints SEATING Head restraints Your vehicle s seats may be equipped with head restraints which are vertically adjustable The purpose of these head restraints is to help limit head motion in the event of a rear collision To properly adjust your head restraints lift the head restraint so that it is located directly b
40. instrument cluster display and the message center display from metric to English units J Select Each press of the SELECT control will select a different function Press the right side of the control to advance the function to the right and press the left side of the control to advance the function to the left To reset any function 1 Push either the right or left side of the SELECT control to choose the desired function 2 Press the RESET control and the selected message center function will be reset to zero Message center functions DISTANCE TO EMPTY DTE This function estimates AVG FUEL approximately how far you can drive ECONOMY with the fuel remaining in your tank Speen under normal driving conditions 21 Instrumentation Remember to turn the ignition OFF when refueling your vehicle Otherwise the display will not show the addition of fuel for a few miles At least four gallons of fuel must be added for the fuel gauge to immediately show the new fuel level The DTE function will flash for 5 seconds and sound a tone for 1 second when you have approximately e 80 km 50 miles left before you run out of fuel e 40 km 25 miles e 16 km 10 miles The message center will remain in the DTE function until the SELECT control is pressed to change functions Displayed DTE will not be equal to AVG ECON multiplied by the FUEL REMAIN value DTE is calculated
41. light will illuminate If the engine reaches a preset over temperature condition the engine will automatically switch to alternating cylinder operation Each disabled cylinder acts as an air pump and cools the engine When this occurs the vehicle will still operate However e the engine power will be limited e the air conditioning system will be disabled 165 Maintenance and care Continued operation will increase the engine temperature e the E symbol will begin to flash e if your vehicle is equipped with digital gauges the gauge bars will flash and a tone will sound every five seconds for one minute e the engine will completely shut down causing steering and braking effort to increase Once the engine temperature cools the engine can be re started Take your vehicle to a service facility as soon as possible to minimize engine damage When fail safe mode is activated You have limited engine power when in the fail safe mode so drive the vehicle with caution The vehicle will not be able to maintain high speed operation and the engine will run rough Remember that the engine is capable of completely shutting down automatically to prevent engine damage therefore 1 Pull off the road as soon as safely possible and turn off the engine 2 Arrange for the vehicle to be taken to a service facility 3 If this is not possible wait a short period for the engine to cool 4 Check the coolant level and replenish if low
42. lower fan speed FLR DEF DEF V LO The display will show Fi to indicate a a manual fan operation T mi gt Cc e To return to automatic fan operation press AUTOMATIC Manual override controls The override controls are located at the bottom of the EATC and allow you to determine where airflow is amme directed To return to full automatic control press AUTOMATIC The air conditioning compressor can operate in all modes except FLOOR and VENT It will also operate only when required when AUTOMATIC has been selected However the air conditioning will only function if the outside temperature is about 10 C 50 F or higher Since the air conditioner removes considerable moisture from the air during operation it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle Under normal conditions your vehicle s climate control system should be left in any position other than MAX A C or OFF when the vehicle is parked This allows the vehicle to breathe through the outside air inlet duct e MAX A C Uses recirculated air to cool the vehicle The temperature display will remain the same and air will be cooled based on the selected temperature To exit press AUTOMATIC or any other override controls MAX A C is noisier than NORM A C but more 31 Controls and features econom
43. lumbar support if equipped The power lumbar control is located on the outboard side of the seat Press one side of the control to adjust firmness Press the other side of the control to adjust softness SAFETY RESTRAINTS Safety restraints precautions A Always drive and ride with your seatback upright and the lap belt snug and low across the hips A To reduce the risk of injury make sure children sit where they can be properly restrained A Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision 95 Seating and safety restraints All occupants of the vehicle including the driver should always properly wear their safety belts even when an air bag SRS is provided It is extremely dangerous to ride in a cargo area inside or outside of a vehicle In a collision people riding in these areas are more likely to be seriously injured or killed Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts Be sure everyone in your vehicle is in a seat and using a safety belt properly In a rollover crash an unbelted person is significantly more likely to die than a person wearing a seat belt Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair 1 Use the shoulder belt on the
44. oil pressure in the system Sufficient pressure exists as long as the needle remains H in the normal range the area between the H and L OIL If the gauge indicates low pressure stop the vehicle as soon as safely possible and switch off the engine L immediately Check the oil level nN 19 Instrumentation Add oil if needed refer to Engine oil in the Maintenance and care chapter If the oil level is correct have your vehicle checked at your dealership or by a qualified technician ELECTRONIC MESSAGE CENTER The electronic message center only CHECK AIRSUSPENSION DOOR works when the ignition is in the OVERDRIVE OFF AJAR ON position nr w w I kA WASHER MILES The message center allows you to FLUID _ _ A _ GAL ir suspension trunk ajar washer TUNKAJAR _ LTR 100 im USE ie AUTS ae DISTANCE AVG FUEL fluid low TO EMPTY ECONOMY e see how many kilometers miles Pe TRIP I RALA you can drive before running out of fuel e see when overdrive has been deactivated e monitor the average fuel economy e check the distance traveled during a trip on either Trip A or Trip B e monitor the average speed Selectable features Reset Press this control to reset the selected message center function to zero The only functions which can be reset are e AVG ECON e TRIP A or TRIP B e AVG SPEED 20 Instrumentation E M Press this control to switch the electronic
45. on the driver s door trim panel and can be operated at any time POWER WINDOWS Controls and features A y Press and hold the rocker switches to open and close windows e Press the top portion of the rocker switch to close l l 75 Controls and features e Press the bottom portion of the rocker switch to open Express down e Press AUTO and release quickly The window will open fully Depress again to stop window A operation NS Window lock The window lock feature allows only the driver to operate the power x windows To lock out all the window controls a WINDOW LOCK except for the driver s press the left side of the control Press the right side to restore the window controls 76 Controls and features POWER DOOR LOCKS Press U to unlock all doors and L to Fa lock all doors a Smart locks With the key in the ignition in any switch position and either the driver s or passenger s door open the doors cannot be locked using the front door lock switches While the key is in the ignition the vehicle can be locked by manually pressing the lock control operating the remote entry transmitter or operating the drivers door lock with the key POWER SIDE VIEW MIRRORS The power mirrors can be operated at any time To adjust your mirrors 1 Select L to adjust the left mirror or R to adjust the right mirror 77 Controls and features 2 Move the contr
46. or Ford Motor Service Company in the U S and Ford of Canada Gin Canada It provides the following e benefits during the warranty period depending on the plan you purchase such as reimbursement for rentals coverage for certain maintenance and wear items e protection against repair costs after your Bumper to Bumper Warranty expires You may purchase Ford ESP from any participating Ford and Lincoln Mercury and Ford of Canada dealer There are several plans available in various time distance and deductible combinations which can be tailored to fit your own driving needs Ford ESP also offers reimbursement benefits for towing and rental coverage In Hawaii rules vary See your dealer for details When you buy Ford ESP you receive Peace of Mind protection throughout the United States and Canada provided by a network of more than 5 000 participating Ford or Lincoln Mercury and Ford of Canada dealers If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle you may still be eligible Please contact your dealer for further information Since this information is subject to change please ask your dealer for complete details about Ford Extended Service Plan coverage options Geiting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle When you need warranty repairs your selling dealer would like you to return to it fo
47. or enable Belt Minder if it is currently disabled 7 Confirmation of disabling Belt Minder is provided by flashing the safety belt warning light four times per second for three seconds 8 Confirmation of enabling Belt Minder is provided by flashing the safety belt warning light four times per second for three seconds followed by three seconds with the safety belt warning light off then followed by flashing the safety belt warning light four times per second for three seconds again 9 After receiving confirmation the deactivation activation procedure is complete Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged Inspect the safety belts to make sure there are no nicks wears or cuts replacing if necessary All safety belt assemblies including retractors buckles front seat belt buckle assemblies buckle support assemblies slide bar if equipped shoulder belt height adjusters Gf equipped shoulder belt guide on seatback if equipped child safety seat tether bracket assemblies if equipped and attaching hardware should be inspected after a collision Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced However if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly they do not need to be replaced Safety belt assemblies not in use during
48. outside shoulder only Never wear the shoulder belt under the arm 2 Never swing the safety belt around your neck over the inside shoulder 3 Never use a single belt for more than one person Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints Combination lap and shoulder belts 1 Insert the belt tongue into the proper buckle the buckle closest to the direction the tongue is coming from until you hear a snap and feel 7 7 it latch Make sure the tongue is a securely fastened in the buckle e 2 y 96 Seating and safety restraints 2 To unfasten push the release button and remove the tongue from the buckle XN The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts The front passenger and rear seat outboard safety belts have two types of locking modes described below Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement For example if the driver brakes suddenly or turns a corner sharply or the vehicle receives an impact of approximately 8 km h 5 mph or more the combination safety belts will lock to help reduce forward movement of the driver and passengers Automatic locking mode In this mode the shoulder belt is automatically pre locked The belt will still retra
49. risk of personal injury do not put any part of your body under the vehicle while changing a tire Do not start the engine when your vehicle is on the jack The jack is only meant for changing the tire e Never use the rear differential as a jacking point 8 Remove the lug nuts with the lug wrench 9 Replace the flat tire with the spare tire making sure the valve stem is facing outward Reinstall lug nuts until the wheel is snug against the hub Do not fully tighten the lug nuts until the wheel has been lowered 10 Lower the wheel by turning the jack handle counterclockwise 11 Remove the jack and fully tighten the lug nuts in the order shown 12 Put flat tire jack and lug wrench away 13 Turn on the air suspension switch if equipped Anti theft lug nuts if equipped If your vehicle is equipped with this feature one of the lug nuts on each wheel must be removed and replaced with a special key The key and registration card are attached to the lug wrench and stored with the spare tire If you lose the key send the registration card to the manufacturer not the dealer to get a replacement key If the lug wrench lug nut key assembly is lost see your nearest Ford or Lincoln Mercury dealer who has access to the master set of keys Do not use an impact wrench with the anti theft key 146 Roadside emergencies To remove the anti theft lug nut 1 Insert the key over the locking q lug nut Make sure you
50. run both engines for an additional three minutes before disconnecting the jumper cables Removing the jumper cables Remove the jumper cables in the reverse order that they were connected 1 Remove the jumper cable from the ground metal surface 2 Remove the jumper cable on the negative connection of the booster vehicle s battery 150 Roadside emergencies 3 Remove the jumper cable from the positive terminal of the booster vehicle s battery 4 Remove the jumper cable from the positive terminal of the disabled vehicle s battery After the disabled vehicle has been started and the jumper cables removed allow it to idle for several minutes so the engine computer can relearn its idle conditions 151 Roadside emergencies WRECKER TOWING If you need to have your vehicle towed contact a professional towing service or if you are a member your roadside assistance center It is recommended that your vehicle be towed with a wheel lift or flatbed equipment Do not tow with a slingbelt Ford Motor Company has not approved a slingbelt towing procedure Before your vehicle can be towed the air suspension control in the luggage compartment must be turned to the OFF position if equipped If the vehicle is towed by other means or incorrectly vehicle damage may occur Ford Motor Company provides a towing manual for all authorized tow truck o
51. seat occupants by 45 in cars and by 60 in light trucks Traffic is light Nearly 1 of 2 deaths occur in single vehicle crashes many when no other vehicles are around Belts wrinkle my Possibly but a serious crash can do much more than clothes wrinkle your clothes particularly if you are unbelted The people I m Set the example teen deaths occur 4 times more with don t wear often in vehicles with TWO or MORE people belts Children and younger brothers sisters imitate behavior they see I have an air Air bags offer greater protection when used with bag safety belts Frontal airbags are not designed to inflate in rear and side crashes or rollovers Td rather be Not a good idea people who are ejected are 40 thrown clear times more likely to DIE Safety belts help prevent ejection WE CAN T PICK OUR CRASH Do not sit on top of a buckled safety belt to avoid the Belt Minder chime Sitting on the safety belt will increase risk of injury in an accident To disable one time or deactivate the Belt Minder feature please follow the directions stated below 102 Seating and safety restraints One time disable Anytime the safety belt is buckled and then unbuckled during an ignition ON cycle Belt Minder will be disabled for that ignition cycle only Deactivating activating the belt minder feature Read steps 1 9 thoroughly before proceeding with the deactivation activation programming proced
52. slow to a fast flash Operating the HomeLink Universal Transceiver Once programmed the HomeLink Universal Transceiver can be used in 19 place of hand held transmitters To operate simply press and release the appropriate HomeLink button O the red light will illuminate indicating the signal is being transmitted Rolling code programming Rolling code garage door openers or other rolling code devices which are code protected and manufactured after 1996 may be determined by the following e Reference the device owner s manual for verification e The hand held transmitter appears to program the HomeLink Universal Transceiver but does not activate the device Press and hold the trained HomeLink button The device has the rolling code feature if the indicator light flashes rapidly and then turns solid after two seconds After completing the Programming functions follow these steps to train a garage door opener with the rolling code feature 1 Locate the training button on the garage door motor head unit Refer to the garage door opener manual or call 1 800 355 3515 or on the Internet at HomeLink jci com if there is difficulty locating the training button 2 Press the training button on the garage door motor head unit which will activate the training light 71 Controls and features 3 Press and release the programmed HomeLink button 19 Press and release the Hom
53. system warning light or the temperature warning light fluid leaks strange odors smoke or loss of engine power could indicate that the emission control system is not working properly Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment Do not make any unauthorized changes to your vehicle or engine By law vehicle owners and anyone who manufactures repairs services sells leases trades vehicles or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working Information about your vehicle s emission system is on the Vehicle Emission Control Information Decal located on or near the engine This decal identifies engine displacement and gives some tune up specifications Please consult your Warranty Guide for complete emission warranty information Readiness for Inspection Maintenance I M testing In some localities it may be a legal requirement to pass an I M test of the on board diagnostics system If your Check Engine Service Engine Soon light is on refer to the description in the Warning Lights and Chimes section of the Instrumentation chapter Your vehicle may not pass the I M test with the Check Engine Service Engine Soon light on 187 Maintenance and care If the vehicle s powertrain system or its battery has just been serviced the on board diagnostics system is reset to a not
54. the eyes Do not attempt to disassemble the case If sound skips e You may be traveling on a rough road playing badly scratched discs or the disc may be dirty Skipping will not scratch the discs or damage the player If your changer does not work it may be that e A disc is already loaded where you want to insert a disc e The disc is inserted with the label surface downward e The disc is dusty or defective e The player s internal temperature is above 60 C 140 F Allow the player to cool down before operating A disc with format and dimensions not within industry standards is inserted Cleaning compact discs Inspect all discs for contamination before playing If necessary clean discs only with an approved CD cleaner and wipe from the center out to the edge Do not use circular motion CD and CD changer care e Handle discs by their edges only Never touch the playing surface e Do not expose discs to direct sunlight or heat sources for extended periods of time 61 Controls and features e Do not insert more than one disc into each slot of the CD changer magazine Cleaning cassetie player if equipped Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation Cassette and cassette player care e Use only cassettes that are 90 minutes long or less e Do not expose tapes to direct sunlight high humidity extreme heat or e
55. the brakes several times to dry them Waxing your vehicle Waxing your vehicle on a regular basis will reduce minor scratches and paint damage Wax when water stops beading on the surface This could be every three or four months depending on operating conditions Use only carnauba or synthetic based waxes Use a cleaning fluid with a clean cloth to remove any bugs before waxing your vehicle Use tar remover to remove any tar spots Avoid getting wax on the windshield or on any surfaces which appear coarse or bumpy If you have wax applied at a commercial car wash it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield 194 Maintenance and care Repairing paint chips Minor scratches or paint damage from road debris may be repaired with the Ultra Touch Prep and Finishing Kit F7AZ 19K507 BA Lacquer Touch up Paint HALBZ 19500 XXXXA or Exterior Acrylic Spray Lacquer HALAZ 19500 XXXXA from the Ford Car Care Chemicals line Please note that the part numbers shown as XXXX above will vary with your vehicle s specific coloring Observe the application instructions on the products Remove particles such as bird droppings tree sap insect remains tar spots road salt and industrial fallout immediately Cleaning the wheels Wash with the same detergent as the body of your vehicle Do not use acid based or alcohol based wheel cleaners steel wool fuel or str
56. then dry with a dry cloth Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel The dull finish in this area helps protect the driver from undesirable windshield reflection Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the air bag system 197 Maintenance and care Cleaning the instrument cluster lens Clean with a damp cloth then dry with a dry cloth Do not use household or glass cleaners as these may damage the lens Cleaning seats equipped with side air bags Remove dust and loose dirt with a whisk broom or a vacuum cleaner Remove fresh spots immediately Follow the directions that come with the cleaner Do not saturate the seat cover with upholstery cleaner Do not use chemical solvents or strong detergents when cleaning the seat mounted side air bag Such products could contaminate the side air bag system and affect performance of the side air bag in a collision Woodtone trim Wipe stains with a soft cloth and a multi purpose cleaning solution Inside windows Use Ultra Clear Spray Glass Cleaner E4AZ 19C507 AA for the inside windows if they become fogged Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets Do not bleach or dye the belts because these actions may weaken the belt webbing Check the safe
57. to the opposite side of the tape To stop on a particular selection press the control again Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD The CD scans in a forward direction wrapping back to the first track at the end of the CD To stop on a particular selection press the control again Radio station memory preset The radio is equipped with six station memory preset controls These controls can be used to select up to six preset AM stations and twelve FM stations six in FM1 and six in FM2 Setting memory preset siations 1 Select the frequency band with the AM FM select control 2 Select a station Refer to Tune adjust or Seek function for more information on selecting a station 3 Press and hold a memory preset control until the sound returns indicating the station is held in memory on the control you selected Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations This feature is helpful on trips when you travel between cities with different radio stations 53 Controls and features Starting autoset memory preset 1 Select a frequency using the AM FM select controls 2 Press the AUTO control 3 When the first six strong stations AUTO are filled the station stored in memory preset control 1 will start playing If there are less than six strong stations available on th
58. using a method that considers the fuel economy of the last 800 km 500 miles driven If CO or CS is displayed there is a problem with the fuel indication system and you should contact your dealer for service as soon as possible AVG FUEL ECONOMY average fuel economy Select this function to display your DISTANCE average fuel economy in liters 100 TOEMPTY km or miles gallon TRIP TRIP AG If you calculate your average fuel economy by dividing miles traveled by gallons used your figure may be different than displayed for the following reasons e your vehicle was not perfectly level during fill up e differences in the automatic shut off points on the fuel pumps at service stations variations in top off procedure from one fill up to another rounding of the displayed values to the nearest 0 1 liter gallons 22 Instrumentation Press the RESET control while AVG ECON is displayed to reset the function The average displayed is the average since the last reset TRIP A and TRIP B These two functions allow you to DISTANCE AVG FUEL see how far you have traveled since TO EMPTY ECONOMY you last reset Trip A and Trip B are TRE ene completely independent and must be reset individually DISTANCE AVG FUEL To reset either trip feature to zero 10 eee aaa press the RESET control while the ua appropriate trip distance feature TRIP A or TRIP B is displayed AVG SPEED ave
59. 2C197 A Lubricant 80W 90 Premium Rear Axle Lubricant Windshield Ultra clear C9AZ 19550 AC ESR M17P5 A washer fluid Windshield Washer Concentrate 1 Use only brake fluids certified to meet Ford specifications DOT 3 fluid is recommended However if DOT 3 is not available DOT 4 fluid can be used 2 Add 118 ml 4 oz of Additive Friction Modifier C8AZ 19B546 A or equivalent meeting Ford specification EST M2C118 A for complete refill of Traction Lok rear axles 3 Ensure the correct automatic transmission fluid is used Transmission fluid requirements are indicated on the dipstick or on the dipstick handle MERCON and MERCON V are not interchangeable DO NOT mix MERCON and MERCON V Refer to your Scheduled Maintenance Guide to determine the correct service interval 202 Capacities and specifications ENGINE DATA Engine AGL VSengine Spark plug gap 1 3 1 4 mm 0 052 0 056 inch Coil on plug 10 061 VEHICLE DIMENSIONS 203 Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located The Certification Label is located on the front door latch pillar on the driver s side 204 MFD BY FORD MOTOR CO IN U S
60. American Customer Assistance Center at 1 800 392 3673 Ford TDD for the hearing impaired 1 800 232 5952 or by writing to the Center at the following address Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P O Box 6248 Dearborn Michigan 48121 UTILIZING THE MEDIATION ARBITRATION PROGRAM CANADA ONLY In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory related vehicle service concern have been unsatisfactory Ford of Canada participates in an impartial third party mediation arbitration program administered by the Canadian Motor Vehicle Arbitration Plan CAMVAP The CAMVAP program is a straight forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings In the CAMVAP program impartial third party arbitrators conduct hearings at mutually convenient times and places in an informal environment These impartial arbitrators review the positions of the parties make decisions and when appropriate render awards to resolve disputes CAMVAP decisions are fast fair and final the arbitrator s award is binding both to you and Ford of Canada CAMVAP services are available in all territories and provinces except Quebec For more information without charge or obligation call you
61. Based Master Lighting Switch Fog Lamps Front Fuel Pump Reset Windshield Defrost Demist Power Windows Front Rear Be gt PENG yi ABA See Owner s Guide Air Bag Front Child Seat Child Seat Tether Anchorage Anti Lock Brake System Traction Control Hazard Warning Flasher Fuse Compartment Windshield Wash Wipe Rear Window Defrost Demist Power Window Lockout Introduction Vehicle Symbol Glossary Child Safety Door Lock Unlock Panic Alarm Engine Coolant Do Not Open When Hot Avoid Smoking Flames or Sparks Explosive Gas Power Steering Fluid Emission System Passenger Compartment bg Air Filter E Bx Interior Luggage Compartment Release Symbol Engine Oil Engine Coolant Temperature Battery Battery Acid Fan Warning Maintain Correct Fluid Level Engine Air Filter Jack ASX D gt LI fi y e h aja Instrumentation Instrument panel dimmer switch ee ps 24 Driver air bag pg 105 Headlamp control pg 24 PUSH INTERIOR Rear window defroster control pg 25 Turn signal and wiper washer control Speed seg pg 63 pg 65 if equipped Instrumentation Gearshift with O D control Electronic sound system pg 128 pg 35 Traction control switch Climate control systems pg 123 pg 26 Clock pg 34 Instrumentation WARNING LIGHTS AND CHIMES St
62. CONTROL RESUME controls are pressed It turns off when the speed control OFF control is pressed the brake is applied or the ignition is turned to the OFF position HOMELINK UNIVERSAL TRANSCEIVER IF EQUIPPED The HomeLink Universal Transceiver located on the driver s visor provides a convenient way to replace up to three hand held transmitters with a single built in device This feature will learn the radio frequency codes of most current transmitters to operate garage doors entry gates security systems entry door locks and home or office lighting When programming your HomeLink Universal Transceiver to a garage door or gate be sure that people and objects are out of the way to prevent potential harm or damage Do not use the HomeLink Universal Transceiver with any garage door opener that lacks safety stop and reverse features as required by U S federal safety standards this includes any garage door opener model manufactured before April 1 1982 A garage door which cannot detect an object signaling the door to stop and reverse does not meet current U S federal safety standards For more information on this matter call toll free 1 800 355 3515 or on the Internet at HomeLink jci com 69 Controls and features Programming 1 Prepare for programming the HomeLink Universal Transceiver by AT erasing the three factory default codes by holding down the two outside buttons until the red light O O begins to
63. Canada 136 Roadside emergencies Roadside coverage beyond basic warranty In the United States you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer HAZARD FLASHER A Use only in an emergency to warn traffic of vehicle breakdown approaching danger etc The hazard flashers can be operated when the ignition is off e The hazard lights control is located on top of the steering column Depress hazard lights control to activate all hazard flashers simultaneously A e Depress control again to turn the flashers off RESETTING THE FUEL PUMP SHUT OFF SWITCH The fuel pump shut off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt After a collision if the engine cranks but does not start the fuel pump shut off switch may have been activated 137 Roadside emergencies The fuel pump shut off switch is located on the left side of the trunk behind the trunk liner lt D Use the following procedure to reset the fuel pump shut off switch 1 Turn the ignition to the OFF position 2 Check the fuel system for leaks 3 If no fuel leak is apparent reset the fuel pump shut off switch by pushing in on the reset button 4 Turn the ignition to the ON position Pause for a few seconds and return the key to the OFF position 5 Make a
64. Contents Before driving Introduction 2 Instrumentation 6 Controls and features 24 Seating and safety restraints 91 Starting and driving Starting 117 Driving 121 Roadside emergencies 136 Servicing Maintenance and care 153 Capacities and specifications 200 Customer assistance 206 Reporting safety defects 217 Index 218 All rights reserved Reproduction by any means electronic or mechanical including photocopying recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company Ford may change the contents without notice and without incurring obligation Copyright 1999 Ford Motor Company Introduction The following warning may be required by California law CALIFORNIA Proposition 65 Warning Engine exhaust some if its constituents and certain vehicle components contain or emit chemicals known to the State of California to cause cancer or birth defects or other reproductive harm ICONS Indicates a safety alert Read the following section on Warnings Indicates vehicle information related to recycling and other environmental concerns will follow Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment Indicates a message regarding child safety restraints Refer to Seating CO and safety restraints for more infor
65. Ford Triple Clean Ford Ultra Clear Spray Glass Cleaner not available in Canada May be sold with the Motorcraft name FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford accessories are available for your vehicle through your local authorized Ford Lincoln Mercury or Ford of Canada dealer These quality accessories have been specifically engineered to fulfill your automotive needs they are custom designed to complement the style and aerodynamic appearance of your vehicle In addition each accessory is made from high quality materials and meets or exceeds Ford s rigid engineering and safety specifications Ford accessories are warranted for up to 12 months or 20 000 km 12 000 miles on all cars and light trucks and 12 months with unlimited distance on medium heavy duty trucks unless the accessory is installed on a new vehicle then the warranty becomes the balance of the new vehicle s warranty or the accessories warranty whichever is greater See your dealer for complete warranty information and availability Not all accessories are available for all models Vehicle Security Remote keyless entry Styled wheel protector locks Vehicle security systems 214 Customer assistance Comfort and convenience Cargo nets Engine block heaters Travel equipment Daytime running lights Heavy duty battery Protection and appearance equipment Air bag anti theft locks Carpet floor mats Cleaners waxes and polishes Flat splash guar
66. P O Box 6248 Dearborn Michigan 48121 1 800 392 3673 FORD TDD for the hearing impaired 1 800 232 5952 In Canada Customer Assistance Centre Ford Motor Company of Canada Limited P O Box 2000 Oakville Ontario L6J 5E4 1 800 565 3673 FORD 207 Customer assistance If you own a Lincoln vehicle and are away from home when your vehicle needs service or if you need more help than the dealership could provide after following the steps described above contact the Ford Customer Assistance Center to find an authorized dealership to help you In the United States Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P O Box 6248 Dearborn Michigan 48121 1 800 521 4140 TDD for the hearing impaired 1 800 232 5952 In Canada Customer Assistance Centre Ford Motor Company of Canada Limited P O Box 2000 Oakville Ontario L6J 5E4 1 800 565 3673 FORD In order to help you service your Ford or Lincoln Mercury vehicle please have the following information available when contacting a Customer Assistance Center e Your telephone number home and business e The name of the dealer and the city where the dealership is located e The year and make of your vehicle e The date of vehicle purchase e The current odometer reading e The vehicle identification number VIN If you still have a complaint involving a warranty dispute you may wish to contact the Dispute Settlement Board U S or th
67. PS The headlamps on your vehicle are properly aimed at the assembly plant If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford approved cleaners polishes and waxes 193 Maintenance and care Washing your vehicle Wash your vehicle regularly with cold or lukewarm water Never use strong detergents or soap If your vehicle is particularly dirty use a quality car wash detergent Always use a clean sponge washing glove or similar device and plenty of water for best results To avoid spots avoid washing when the hood is still warm immediately after or during exposure to strong sunlight During winter months it is especially important to wash the vehicle on a regular basis Large quantities of dirt and road salt are difficult to remove and also cause damage to the vehicle Any gasoline spilled on the vehicle or deposits such as bird droppings should be washed and sponged off as soon as possible Deposits not removed promptly can cause damage to the vehicle s paintwork Remove any exterior accessories such as antennas before entering a car wash If you have wax applied to the vehicle at a commercial car wash it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield After washing apply
68. Press 1 2 within 5 seconds of step a 3 Press and hold 1 2 for two seconds All of the vehicle doors will 1 2 3 4 5 6 7 8 9 0 lock and then unlock to confirm erasure Unlocking the doors and releasing the trunk with the keyless entry system To unlock the driver door enter either the factory set code or personal code each digit pressed within 5 seconds of prior digit The interior lamps will illuminate To unlock all doors enter the factory set code or personal code 1 2 3 4 driver door unlocks and press 3 4 within five seconds 5 6 7 8 9 0 To release the trunk enter the factory set code or personal code driver door unlocks and press 5 6 within five seconds After the factory set code or personal code has been entered you can unlock all doors press 3 4 and release the trunk press 5 6 as long as the controls are pressed within 5 seconds of each other 88 Controls and features Locking doors with the keyless entry system It is not necessary to enter the factory set code prior to locking all doors To lock the doors Press 7 8 and 9 0 at the same time 1 2 3 4 5 6 7 8 9 0 INTERIOR LUGGAGE COMPARTMENT RELEASE IF EQUIPPED Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked
69. Set the parking brake and ensure the gearshift is securely latched in P Park 2 Turn off the engine and remove the key 3 Block the wheels to prevent the vehicle from moving unexpectedly Working with the engine on 1 Set the parking brake and ensure the gearshift is securely latched in P Park 2 Block the wheels to prevent the vehicle from moving unexpectedly Do not start your engine with the air cleaner removed and do not remove it while the engine is running OPENING THE HOOD am gt 1 Inside the vehicle pull the hood release handle located under the instrument panel 2 Go to the front of the vehicle and release the auxiliary latch that is located under the front of the hood 3 Lift the hood until the lift cylinders hold it open 154 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4 6L SOHC V8 engine Q X Ai ESSN TANIN UT XR IAY f4 e Tr Brake fluid reservoir Engine oil dipstick Engine oil filler cap Windshield washer fluid reservoir Air filter assembly Power steering fluid reservoir Engine coolant reservoir Battery Oo o noan FP WH FR Automatic transmission fluid dipstick 155 Maintenance and care ENGINE OIL 92 Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil 1 Make sure the vehicle is on level gr
70. Use 1 Low to provide maximum engine braking on steep downgrades Upshifts can be made by shifting to 2 Second or to Overdrive Selecting 1 Low at PRNO2 C oo reas higher speeds causes the transmission to shift to a lower gear and will shift to 1 Low after vehicle decelerates to the proper speed TRACTION LOK AXLE IF EQUIPPED This axle provides added traction on slippery surfaces particularly when one wheel is on a poor traction surface Under normal conditions the Traction Lok axle functions like a standard rear axle Extended use of other than the manufacturer s specified size tires on a Traction Lok rear axle could result in a permanent reduction in effectiveness This loss of effectiveness does not affect normal driving and should not be noticeable to the driver To avoid injury never run the engine with one wheel off the ground such as when changing a tire VEHICLE LOADING Before loading a vehicle familiarize yourself with the following terms e Base Curb Weight Weight of the vehicle including any standard equipment fluids lubricants etc It does not include passengers or aftermarket equipment 129 Driving Payload Combined maximum allowable weight of cargo passengers and optional equipment The payload equals the gross vehicle weight rating minus base curb weight GVW Gross Vehicle Weight Base curb weight plus payload weight The GVW is not a limit or a specification GVWR Gross V
71. acceleration and deceleration and have your vehicle serviced at the first available opportunity Under engine misfire conditions excessive exhaust temperatures could damage the catalytic converter the fuel system interior floor coverings or other vehicle components possibly causing a fire Air bag readiness Momentarily illuminates when the AIR ignition is turned ON If the light fails to illuminate continues to flash BAG or remains on have the system serviced immediately Engine coolant temperature if equipped Illuminates when the engine coolant temperature is high Stop the E vehicle as soon as safely possible esp Saag switch off the engine and let it cool Never remove the coolant recovery cap while the engine is running or hot Refer to Engine coolant in the Maintenance and care chapter If light stays on or continues to turn on after the vehicle warms up have your vehicle serviced This light also illuminates briefly when the ignition key is turned to ON Safety belt Momentarily illuminates when the ignition is turned to the ON position hb to remind you to fasten your safety belts For more information refer to the Seating and safety restraints chapter 10 Instrumentation Brake system warning e Standard instrument cluster BRAKE e Optional instrument cluster BR AKE Momentarily illuminates when the ignition is turned to the ON C P position Also illuminates if the parking b
72. andard instrument cluster lt FUEL FILL DOOR CHECK OU lkm ENGINE SPEED CONTROL km h H m F 20 y y MPH _ D 8 0 a R an M aa E a MEM prn e1 Low fuel if equipped Iluminates as an early reminder of a low fuel condition indicated on the fuel gauge refer to Fuel gauge in this chapter for more information When refueling after the light CHECK AIR SUSPENSION OVERDRIVE OFF DOOR AJAR WASHER N yt yt MILES FLUID I ti GAL TRUNK AJAR LTR 100 km DISTANCE AVG FUEL TO EMPTY ECONOMY CF CFI LOW FUEL comes on the amount of fuel that is added will be less than the advertised capacity since there is fuel still in the tank The ignition must be in the ON position for this lamp to illuminate The lamp will also illuminate for several seconds after the ignition is turned to the ON position regardless of the fuel level to ensure your bulb is working Instrumentation Check engine Your vehicle is equipped with a computer that monitors the engine s CHECK emission control system This system is commonly known as the ENGINE On Board Diagnostics System OBD II This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards The OBD II system also assists the service technician in properly servicing your vehicle The Check Engine indicator light illumina
73. ard The fast forward control works in CD mode To fast forward in CD changer CD mode press the CD control preset 2 Press the control again to deactivate fast forward mode Eject function Press the control to stop and eject a cb Compression feature Compression adjust brings soft and loud CD passages together for a COMP more consistent listening level Press the COMP control to activate and deactivate compression adjust Shuffle feature The shuffle feature operates in CD SHUFFLE and CD changer mode if equipped and plays all tracks on the current disc in random order Press the SHUFFLE control to start this feature Random order play will continue until the SHUFFLE control is pressed again 49 Controls and features Premium AM FM Siereo Cassette CD Changer Compatible VOL PUSH ON O O Cha e O Ce O REW FF SIDE 1 2 oo COMP SHUFF O Your audio system is equipped with selective lighting a unique lighting strategy This lighting feature is operable when the headlamps are illuminated During the operation of any selected mode lighting for the individual function controls will either illuminate or turn off Those controls which have a function for the specific mode of operation selected will be lit while the controls which have no function for that mode will be turned off Volume power control Press the control to turn the audio system on or off VOL PUSH ON A
74. attery or refilling fluid reservoirs If the battery has been disconnected and reconnected refer to the Battery section of the Maintenance and care chapter 141 Roadside emergencies The high current fuses are coded as follows Location Rating 1 7 20A CB Power door Locks Power Seats Trunk Lid Release Air Suspension System See Fuses 5 and 9 10 5OA See Fuses 1 2 6 7 10 11 13 and Circuit Breaker 14 11 40A See Fuses 4 8 16 and Circuit Breaker 12 142 Roadside emergencies Fuse Relay Fuse Amp Power Distribution Box Description Location Rating 30A PCM Power Relay PCM Natural Gas Vehicle Module High Speed Cooling Fan Relay Rear Window Defrost Relay Also see Fuse 17 Anti Lock Brake Module Police Option Fuse Holder an C Cooling Fan Relay Rear Defrost Relay Horn Relay ee Cooling Fan Relay Air Suspension Pump Relay Police Power Relay Mini Fuses Maxi Fuses Relays Relays are located in the power distribution box and should be replaced by qualified technicians CHANGING THE TIRES If you get a flat tire while driving do not apply the brake heavily Instead gradually decrease your speed Hold the steering wheel firmly and slowly move to a safe place on the side of the road Temporary spare tire information Your vehicle may have a temporary or full size spare tire The temporary spare tire for your vehicle is labeled as such It is smaller than a regular tire and is
75. bring it forward Release the handle when the desired position has been reached Adjusting the power front seats door mounted controls The controls for the power seats are located on the inside of each front door Press the control to recline the S A Never adjust the driver s seat or seatback when the vehicle is moving A Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop tp Always drive and ride with your seatback upright and the lap belt snug and low across the hips fp Reclining the seatback can reduce the effectiveness of the seat s safety belt in the event of a collision eatback forward or backward 93 Seating and safety restraints Press to move the seat forward or backward Press to move the front portion of the seat cushion up or down Press to move the rear portion of the seat cushion up or down Adjusting the power seats seat mounted controls Never adjust the driver s seat or seatback when the vehicle is moving Always drive and ride with your seatback upright and the lap belt snug and low across the hips 94 Seating and safety restraints Reclining the seatback can reduce the effectiveness of the seat s safety belt in the event of a collision The power seat controls are located on the side of the driver s seat Press to raise or lower the seat or to move the seat forward or backward Using the power
76. bulbs can be replaced with out removing the headlamp assembly 1 Make sure headlamp switch is in OFF position then open the hood 2 Remove the protective cover by turning the three knobs to the unlock position 3 Disconnect the electrical connector from the bulb by pulling rearward 4 Rotate the bulb socket counterclockwise and remove from lamp assembly 5 Carefully pull bulb straight out of the socket and push in the new bulb until it snaps locking it into position 6 To complete installation follow the removal procedure in reverse order Replacing tail lamp brake turn lamp bulbs The tail lamp the brake lamp and the turn signal lamp bulbs are located in the tail lamp assembly Follow the same steps to replace either bulb 190 Maintenance and care 1 Open the trunk and carefully pull the carpet away to expose the plastic retainer 2 Remove plastic retainer to expose the lamp assembly hardware 3 Remove three nut and washer assemblies and the lamp assembly from the vehicle 4 Remove the bulb socket by rotating it counterclockwise then pulling it out of the lamp assembly 5 Pull the bulb from the socket and KL push in the new bulb 6 Install the bulb socket into the lamp assembly by rotating it clockwise 7 Install the lamp assembly on the vehicle with three nut and washer assemblies ensuring the washers on the nuts are flush with the body to prevent water from entering the trunk
77. coolant produced by Ford approved processes Not all coolant recycling processes produce coolant which meets Ford specification ESE M97B44 A Use of a recycled engine coolant which does not meet the Ford specification may harm engine and cooling system components Always dispose of used automotive fluids in a responsible manner Follow your community s regulations and standards for recycling and disposing of automotive fluids Coolant refill capacity To find out how much fluid your vehicle s cooling system can hold refer to Refill capacities in the Capacities and specifications chapter Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter 163 Maintenance and care Severe climates If you drive in extremely cold climates less than 36 C 34 F e it may be necessary to increase the coolant concentration above 50 e NEVER increase the coolant concentration above 60 e increased engine coolant concentrations above 60 will decrease the overheat protection characteristics of the engine coolant and may cause engine damage e refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months If you drive in extremely hot climates e it is still necessary to maintain the coolant concentration above 40 e NEVER decrease the coolant concentration bel
78. ct to remove any slack in the shoulder belt The automatic locking mode is not available on the driver safety belt When to use the automatic locking mode e Anytime a child safety seat is installed in a passenger front or outboard rear seating position Gif equipped Children 12 years old and under should be properly restrained in the rear seat whenever possible Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter 97 Seating and safety restraints How to use the automatic locking mode Buckle the combination lap and shoulder belt Grasp the shoulder portion and pull downward until the entire belt is extracted Allow the belt to retract As the belt retracts you will hear a clicking sound This indicates the safety belt is now in the automatic locking mode How to disengage the automatic locking mode Disconnect the combination lap shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive emergency locking mode 98 Seating and safety restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder To lower the shoulder belt height push the button and slide the height adjuster down To raise the height of the shoulder belt slide the height adjuster u
79. ds Front end covers Lubricants and oils Molded splash guards Molded vinyl floor mats Touch up paint Universal floor mats For maximum vehicle performance keep the following information in mind when adding accessories or equipment to your vehicle e When adding accessories equipment passengers and luggage to your vehicle do not exceed the total weight capacity of the vehicle or of the front or rear axle GVWR or GAWR as indicated on the Safety compliance certification label Consult your dealer for specific weight information e The Federal Communications Commission FCC and Canadian Radio Telecommunications Commission CRTC regulate the use of mobile communications systems such as two way radios telephones and theft alarms that are equipped with radio transmitters Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician e Mobile communications systems may harm the operation of your vehicle particularly if they are not properly designed for automotive 215 Customer assistance use or are not properly installed When operated such systems may cause the engine to stumble or stall In addition such systems may be damaged or their performance may be affected by operating your vehicle Citizens band CB transceivers garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your v
80. e Mediation Arbitration Program Canada In some states in the U S you must directly notify Ford in writing before pursuing remedies under your state s warranty laws Ford is also allowed a final repair attempt in some states In the United States a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson Moss Warranty Act or to the extent allowed by state law before pursuing replacement or repurchase remedies provided by certain state laws This 208 Customer assistance dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson Moss Warranty Act or state replacement or repurchase laws THE DISPUTE SETTLEMENT BOARD U S ONLY The Dispute Settlement Board is e an independent third party arbitration program for warranty disputes e available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states Ford Motor Company reserves the right to change eligibility limitations modify procedures and or to discontinue this service without notice and without incurring obligations per applicable state law What kinds of cases does the Board review Unresolved warranty repair concerns or vehicle performance as designed concerns on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any
81. e control to fast forward through the remaining discs Seek function The seek function control works in radio tape or CD mode if equipped Seek function in radio mode e Press lt Q to find the next listenable station down the frequency band e Press to find the next listenable station up the frequency band Seek function in tape mode e Press A to listen to the previous selection on the tape or return to the beginning of the current selection e Press gt to listen to the next selection on the tape Seek function for CD changer e Press lt q to seek to the previous track of the current disc If a selection has been playing for three seconds or more and you press lt q the CD changer will replay that selection from the beginning e Press P gt to seek forward to the next track of the current disc After the last track has been completed the first track of the current disc will automatically replay Scan function The scan function works in radio tape or CD mode if equipped 52 Controls and features Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band Press the SCAN control again to stop the scan mode Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape The tape scans in a forward direction At the end of the tape s first side direction automatically reverses
82. e doors without using the key open trunk disable enable horn chirp disable enable autolock 86 Controls and features See also Remote entry system in this chapter for more information Your vehicle has a factory set 5 digit code that operates the keyless entry system You can also program your own 5 digit personal entry code The factory set code is located e on the owner s wallet card in the glove compartment e taped to the computer module When pressing the controls on the keyless entry keypad press the middle of the controls to ensure a good activation Programming your own entry code 1 Enter the factory set code keypad will illuminate when pressed seconds of step 1 2 Press the 1 2 control within five 3 4 5 6 7 8 9 0 3 Enter your personal 5 digit code Enter each digit within five seconds of the previous one All of the vehicle doors will lock and unlock to confirm programming of the new code Do not set a code that includes five of the same number or presents them in sequential order Thieves can easily figure out these types of codes You can program up to three personal codes to unlock your vehicle These codes do not replace the permanent code that the dealership gave you 87 Controls and features Erasing personal code To erase all of the personal entry codes programmed to a vehicle 1 Enter the factory set code 2
83. e frequency band the remaining memory preset controls will all store the last strong station available To deactivate autoset and return to your audio system s manually set memory stations press the control again Bass adjust The bass adjust control allows you to increase or decrease the audio A system s bass output mA Press the BASS control Use the SEL control to increase or decrease v the amount of bass Treble adjust The treble adjust control allows you to increase or decrease the audio A system s treble output api Press the TREB control Use the SEL control to increase or decrease v the amount of treble Speaker balance adjust Speaker sound distribution can be adjusted between the right and left A speakers ai Press the BAL control Use the SEL control to adjust the sound between v the speakers 54 Controls and features Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers Press the FADE control Use the SEL control to adjust the sound between the front and rear speakers Tape CD select e To begin tape play with a tape loaded into the audio system while in the radio or CD mode press the TAPE control Press the button during rewind or fast forward to stop the rewind or fast forward function To begin CD play Gf equipped with CD changer ensure that the CDs are loaded Press the CD control The first track of the disc will begin playing A
84. e fully and make sure the gearshift is latched in P Park Turn off the ignition whenever you leave your vehicle If the parking brake is fully released but the brake warning lamp remains illuminated the brakes may not be working properly See your dealer or a qualified service technician Driving with a 4 speed automatic transmission Understanding gearshift positions To put your vehicle in gear start the engine depress the brake pedal then move gearshift lever out of P Park Hold the brake pedal down while you move the gearshift lever from P Park to another position If you do not hold the brake pedal down your vehicle may move unexpectedly and injure someone P Park Always come to a complete stop before shifting into P Park Make P RN D 21 sure the gearshift lever is securely o O latched in P Park This position locks the transmission and prevents the rear wheels from turning Always set the parking brake fully and make sure the gearshift lever is latched in P Park Turn off the ignition whenever you leave your vehicle 127 Driving R Reverse With the gearshift lever in R Reverse the vehicle will move backward Always come to a complete stop before shifting into and out of R Reverse N Neutral With the gearshift lever in N Neutral the vehicle can be started P RN D r a and is free to roll Hold the brake are A pedal down while in this gear Overdrive The no
85. e ignition from OFF to ON maintain ignition in ON for at least one second 2 Turn ignition to OFF and remove the first coded key from the ignition 3 Within five seconds of turning the ignition to OFF insert the second previously programmed coded key into the ignition and turn the ignition from OFF to ON maintain ignition in ON for at least one second but no more than five seconds 4 Turn the ignition to OFF and remove the second coded key from the ignition 5 Within 10 seconds of turning the ignition to OFF insert the new unprogrammed key new key valet key into the ignition and turn the ignition from OFF to ON maintain ignition in ON for at least one second This step will program your new key to a coded key 6 To program additional new unprogrammed key s repeat this procedure from step 1 If the programming procedure was successful the new coded key s will start the vehicle s engine The theft indicator located on the instrument panel will light for three seconds and then go out If the programming procedure was not successful the new coded key s will not operate the vehicle s engine The theft indicator will flash on and off Wait at least one minute and then repeat the procedure from step 1 If failure repeats bring your vehicle to your dealership to have the new spare key s programmed KEYLESS ENTRY SYSTEM With the keyless entry keypad you a 1 2 3 4 5 6 7 8 9 0 e lock or unlock the vehicl
86. e on the child seat remove any slack in the belt 9 Before placing the child in the seat forcibly tilt the seat forward and back to make sure the seat is securely held in place x 8 Allow the safety belt to retract to We gt lt 10 Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode you should not be able to pull more belt out If the retractor is not locked unbuckle the belt and repeat steps two through nine Check to make sure the child seat is properly secured before each use 114 Seating and safety restraints Installing child safety seats in the lap belt seating positions 1 Lengthen the lap belt To lengthen the belt hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing 2 Place the child safety seat in the center seating position 3 Route the tongue and webbing through the child seat according to the child seat manufacturer s instructions 4 Insert the belt tongue into the proper buckle for the center seating position until you hear a snap and feel it latch Make sure the tongue is securely fastened to the buckle by pulling on tongue 5 Push down on the child seat while pulling on the loose end of the lap belt webbing to tighten the belt 6 Before placing the child into the child seat forcibly tilt the child seat from side to side and in forward direction to make sure t
87. e the 157 Maintenance and care engine oil filler cap and use a funnel to pour the engine oil into the opening 3 Recheck the engine oil level Make sure the oil level is not above the normal operating range on the engine oil level indicator dipstick 4 Install the indicator and ensure it is fully seated 5 Fully install the engine oil filler cap by turning the filler cap clockwise until three clicks can be heard To avoid possible oil loss DO NOT operate the vehicle with the engine oil level indicator and or the engine oil filler cap removed Engine oil and filter recommendations Look for this certification trademark Motorcraft SAE 5W 30 MOTOR OIL QUART 0 946L Use SAE 5W 30 motor oil certified for gasoline engines by the American Petroleum Institute APD Motor oil displaying the API certification trademark will meet all requirements for your vehicle s engine Ford oil specification is WSS M2C153 G Do not use supplemental engine oil additives oil treatments or engine treatments They are unnecessary and could under certain conditions lead to engine damage which is not covered by your warranty Change your engine oil and filter according to the appropriate schedule listed in the Scheduled Maintenance Guide Ford production and aftermarket Motorcraft oil filters are designed for added engine protection and long life If a replacement oil filter is used that does not meet Ford material and des
88. e to the next frequency up the band whether or not a listenable station is located there Hold for quick movement Tune adjust in CD changer mode if equipped e Press A to move to the previous disc Hold for quick movement e Press B gt to move to the next disc Hold for quick movement 45 Controls and features Seek function The seek function control works in radio CD or CD changer mode if equipped Seek function in radio mode e Press lt Q to find the next listenable station down the frequency band e Press gt to find the next listenable station up the frequency band Seek function in CD or CD changer mode if equipped e Press gt to listen to the next selection on the current disc e Press lt q to listen to the previous selection on the current disc Scan function The scan function works in radio or CD mode Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band Press the SCAN control again to stop the scan mode Scan function in CD or CD changer mode if equipped Press the SCAN control to hear a short sampling of all selections on the current CD The CD scans in a forward direction wrapping back to the first track at the end of the CD To stop on a particular selection press the control again Radio station memory preset The radio is equipped with four or six station memory preset controls These control
89. eLink button a second time to complete the training process Some garage door openers may require this procedure to be done a third time to complete the training The 2nd or 8rd press from step 3 will activate the door The HomeLink Universal Transceiver has now been trained to the receiver The remaining two buttons may now be programmed if this has not previously been done Erasing HomeLink buttons Individual buttons cannot be erased however to erase the three AT programmed buttons 1 Hold down the two outside buttons until the red light begins to flash after 20 seconds 2 Release both buttons N Reprogramming a single HomeLink button To program a device to HomeLink using a HomeLink button previously trained follow these steps 1 Press and hold the desired HomeLink button Do NOT release until step 4 has been completed 2 When the indicator light begins to flash slowly after 20 seconds position the hand held transmitter 5 14 cm 2 to 5 inches away from the HomeLink surface 3 Press and hold the hand held transmitter button 4 The HomeLink indicator light will flash first slowly and then rapidly When the indicator light begins to flash rapidly release both buttons The previous device has now been erased and the new device can be activated by pushing the HomeLink button that has just been programmed 72 Controls and features AUTOMATIC DIMMING INSIDE REAR VIEW
90. ead all information on safety restraints in this guide Children must always be properly restrained Accident statistics N suggest that children are safer when properly restrained in the rear seating positions than in the front seating position Failure to follow these instructions may increase the risk of injury in a collision n Air bags can kill or injure a child in a child seat NEVER place a rear facing child seat in front of an active air bag If you must use a forward facing child seat in the front seat move the seat all the way back SZ a How does the air bag supplemental restraint system work The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system Rather it means the forces were not of the type sufficient to cause activation Air bags are designed to inflate in frontal and near frontal collisions not rollover side impact or rear impacts unless the collision causes sufficient longitudinal deceleration 107 Seating and safety restraints The air bags inflate and deflate rapidly upon activation After air bag deployment it is normal to notice a smoke like powdery residue or smell the burnt propellant This may consist of cornstarch talcum p
91. ear passenger door jamb Hood release Pull handle under the left side of the eee deem Automatic transmission 13 1L 13 9 quarts Use Motorcraft Power steering fluid Fill to line on reservoir Use Motorcraft 1 Use Ford Premium Engine Coolant green in color DO NOT USE Ford Extended Life Engine Coolant orange in color Refer to Adding engine coolant in the Maintenance and Care chapter Ensure the correct automatic transmission fluid is used Transmission fluid requirements are indicated on the dipstick or on the dipstick handle MERCON and MERCON V are not interchangeable DO NOT mix MERCON and MERCON V Refer to your Scheduled Maintenance Guide to determine the correct service interval 3 Indicates only approximate dry fill capacity Some applications may vary based on cooler size and if equipped with in tank cooler The amount of transmission fluid and fluid level should be set by the indication on the dipstick s normal operating range Police Package refill capacity 12 1L 12 8 quarts 224
92. earshift in P Park turn off all accessories and start the engine 3 Run the engine until it reaches normal operating temperature 4 Allow the engine to idle for at least one minute 5 Turn the A C on and allow the engine to idle for at least one minute 6 With your foot on the brake pedal and with the A C on put the vehicle in D Drive and allow the engine to idle for at least one minute 7 Drive the vehicle to complete the relearning process e The vehicle may need to be driven 16 km 10 miles or more to relearn the idle and fuel trim strategy e If you do not allow the engine to relearn its idle trim the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned If the battery has been disconnected or a new battery has been installed the clock must be reset once the battery is reconnected 171 Maintenance and care e Always dispose of automotive siege P batteries in a responsible manner lt S Follow your local authorized YW Y standards for disposal Call your 4 local authorized recycling center to find out more about recycling automotive batteries RECYCLE AIR FILTER MAINTENANCE Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the air filter element When changing the air filter element use only the Motorcraft air filter element listed Refer to Motorcraft Part Numbers in the Capacities and specifications chapter Do not
93. ect up to four preset AM stations and eight FM stations four in FM1 and four in FM2 Setting memory preset siations 1 Select the frequency band with the AM FM select control 2 Select a station Refer to Tune adjust or Seek function for more information on selecting a station 3 Press and hold a memory preset control until the sound returns indicating the station is held in memory on the control you selected ERIERER ED Bass adjust The bass adjust control allows you to increase or decrease the audio system s bass output Press the TONE control once then use the volume knob to adjust the desired level Treble adjust The treble adjust control allows you to increase or decrease the audio system s treble output Press the TONE control twice then use the volume knob to adjust the desired level VOL PUSH ON 37 Controls and features Speaker balance adjust Speaker sound distribution can be V adjusted between the right and left PUSH speakers Press the TONE control three times then use the volume knob to adjust the desired level Speaker fade adjust if equipped Speaker sound can be adjusted between the front and rear speakers Press the TONE control four times then use the volume knob to adjust the desired level Setting the clock Your vehicle is equipped with a separate instrument panel mounted clock Please refer to Clock in this chapter for instructions on setting the cloc
94. ed octane rating Aftermarket products could cause damage to the fuel system Repairs to correct the effects of using an aftermarket product in your fuel may not be covered by your warranty Many of the world s automakers issued the World wide Fuel Charter that recommends gasoline specifications to provide improved performance and emission control system protection for your vehicle Gasolines that meet the World wide Fuel Charter should be used when available Ask your fuel supplier about gasolines that meet the World wide Fuel Charter Cleaner air Ford approves the use of reformulated cleaner burning gasolines to improve air quality These gasolines may contain oxygenates up to 10 ethanol or 15 MTBE Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components 182 Maintenance and care If you have run out of fuel e You may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine e Your Check Engine indicator may come on For more information on the Check Engine indicator refer to the Instrumentation chapter Fuel Filter For fuel filter replacement see your dealer or a qualified service technician Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the fuel filter Replace the fuel filter with an authorized Motorcraft part
95. efer to Engine oil in the Maintenance and care chapter This lamp also illuminates when the ignition is turned to ON and the engine is off Air suspension if equipped e Standard instrument cluster AIR AIR SUSPENSION DOOR OVERDRIVE OFF AJAR e Optional instrument cluster Momentarily illuminates when the ignition is turned to the ON LOW km position Also illuminates when the WASHER MILES air suspension requires repair the FLUID Pam Pot Foe GAL air suspension switch is OFF or the TRUNK AJAR LTR 100 km load limit is exceeded For information on the air suspension system refer to the Driving chapter 12 Instrumentation O D off e Standard instrument cluster 0 D OFF e Optional instrument cluster CHECK AIR EUSPEN AION DOOR i SE ERDRIVE OFF AJAR Illuminates when the Transmission Control Switch TCS refer to LOW i l i km Overdrive control in the Controls WASHER yl MILES and Features chapter has been FLUID GAL pushed turning the transmission TRUNK AJAR LTR 100 km overdrive function OFF When the light is on the transmission does not operate in the overdrive mode refer to the Driving chapter for transmission function and operation The light may also flash steadily if a transmission malfunction is detected If the light does not come on when the Transmission Control Switch is depressed or if the light flashes steadily have your vehicle serviced as soon as possible dama
96. ehicle s operation e Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment ORDERING ADDITIONAL OWNER S LITERATURE To order the publications in this portfolio Make checks payable to HELM INCORPORATED P O Box 07150 Detroit Michigan 48207 For a free publication catalog order toll free 1 800 782 4356 Monday Friday 8 00 a m 6 00 p m EST for credit card holders only Obtaining a French owner s guide French Owner s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada Limited Service Publications P O Box 1580 Station B Mississauga Ontario L4Y 4G3 216 Reporting safety defects REPORTING SAFETY DEFECTS U S ONLY If you believe that your vehicle has a defect that could cause a crash or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying Ford Motor Company If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer or Ford Motor Company To contact NHTSA you may either call the Auto Safety Hotline toll free at 1 800 424 9393 202 366 0123 in the Washington D C area or write to NHTSA U S Department of Transpo
97. ehicle Weight Rating Maximum total weight of the base vehicle passengers optional equipment and cargo The GVWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver s door pillar GAWR Gross Axle Weight Rating Carrying capacity for each axle system The GAWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver s door pillar GCW Gross Combined Weight The combined weight of the towing vehicle including passengers and cargo and the trailer GCWR Gross Combined Weight Rating Maximum combined weight of the towing vehicle including passengers and cargo and the trailer The GCWR indicates the maximum loaded weight that the vehicle is designed to tow Maximum Trailer Weight Rating Maximum weight of a trailer the vehicle is permitted to tow The maximum trailer weight rating is determined by subtracting the vehicle curb weight for each engine transmission combination any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle Maximum Trailer Weight Maximum weight of a trailer the loaded vehicle Gncluding passengers and cargo is permitted to tow It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle Trailer Weight Range Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating Reme
98. ehind your head or as close to that position as possible Refer to the following to raise and lower the head restraints Push or pull the head rests to the desired position A l y Adjusting the front manual seat A Never adjust the driver s seat or seatback when the vehicle is moving Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop Always drive and ride with your seatback upright and the lap belt snug and low across the hips Reclining the seatback can reduce the effectiveness of the seat s safety belt in the event of a collision a a a 91 Seating and safety restraints Lift handle to move seat forward or backward Pull lever up to adjust seatback ee S Using the manual recline function if equipped AN AN AN AN Never adjust the driver s seat or seatback when the vehicle is moving Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop Always drive and ride with your seatback upright and the lap belt snug and low across the hips Reclining the seatback can reduce the effectiveness of the seat s safety belt in the event of a collision To adjust the front seatback using the manual recliner Seating and safety restraints Lift and hold the handle located on the side of the seat Lean against the seatback to adjust it to your desired position You can recline the seat back or
99. elt warning chime is sounding The driver s safety belt is buckled before the ignition switch is turned to the ON position The Belt Minder feature is activated the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds repeating for approximately 5 minutes or until safety belt is buckled The Belt Minder feature will not activate The Belt Minder feature will not activate The purpose of the Belt Minder is to remind occasional wearers to wear safety belts all of the time 101 Seating and safety restraints The following are reasons most often given for not wearing safety belts All statistics based on U S data Reasons given Consider Crashes are rare 36 700 crashes occur every day The more we drive the more we are exposed to rare events even for good drivers in 4 of us will be seriously injured in a crash during our lifetime Tm not going far 3 of 4 fatal crashes occur within 25 miles of home Belts are Ford designs its safety belts to enhance comfort If uncomfortable you are uncomfortable try different positions for the safety belt upper anchorage and seatback which should be as upright as possible this can improve comfort I was in a hurry Prime time for an accident Belt Minder reminds us to take a few seconds to buckle up Seat belts don t Safety belts when used properly reduce risk of work death to front
100. esssseee 69 traction control active 13 turn signal indicator 11 Load limits cece eeeeeeeeeee 129 GAWR aeneae eienn 129 GVWR peara EES 129 trailer towing 0 eee 129 Locks AULOLOGK esterne ei 80 CMIdPrOOL a2 eek soeteageet eenentionaete 78 CO OTS xises5 c2 ses E teh eas T Lubricant specifications 201 203 Lug nuts anti theft 0 00 146 Lumbar support seats 95 Message center osese 20 reset button wo eeeeeeeeees 20 select button ssensossesossoesssssees 21 Mirrors automatic dimming tearview MITTOT sicsscnntien ia 73 Cleaning oy 25 cactcenissacs cesseeherseasiees 195 side view mirrors power 77 Motorcraft parts 183 200 OCtaMe rating seses 182 Odometer E 17 Oil see Engine oil 0 0 156 OVELATIVE decscestiss caastiseenesadcees 65 128 Panic alarm feature remote entry system 82 Parking brake icccccscscsissceeeses 122 Parts see Motorcraft parts 200 Power distribution box see FUSES cessccsccscessnrsesneosseateass 141 Power door locks 0 6 77 80 Power Steering scrcrsosicsirsas 125 fluid checking and adding 167 fluid refill capacity 0 200 fluid specifications 201 203 Radioen 35 Relays orerar 138 143 Remote entry system 79 82 illuminated entry cc cee 82 locking unlocking doors 79 opening the trunk 82 PANIC AAPM ooo eeeceeeeseeeeeeteees 82
101. est B and C representing the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sustained high temperature can cause the material of the tire to degenerate and reduce tire life and excessive temperature can lead to sudden tire failure The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No 109 Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law The temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive speed underinflation or excessive loading either separately or in combination can cause heat buildup and possible tire failure 175 Maintenance and care SERVICING YOUR TIRES Checking the tire pressure e Use an accurate tire pressure gauge e Check the tire pressure when tires are cold after the vehicle has been parked for at least one hour or has been driven less than 5 km 3 miles e Adjust tire pressure to recommended specifications found on the Tire Pressure label Improperly inflated tires can affect vehicle handling and can fail suddenly possibly resulting in loss of vehicle control Tire rotation Because your vehicle s tires perform different jobs they often wear differently To make sure
102. etainers of the vehicle To connect the trailer s safety chains cross the chains under the trailer tongue and allow slack for turning corners If you use a rental trailer follow the instructions that the rental agency gives to you Do not attach safety chains to the bumper Trailer brakes Electric brakes and manual automatic or surge type trailer brakes are safe if installed properly and adjusted to the manufacturer s specifications The trailer brakes must meet local and Federal regulations Do not connect a trailer s hydraulic brake system directly to your vehicle s brake system Your vehicle may not have enough braking power and your chances of having a collision greatly increase The braking system of the tow vehicle is rated for operation at the GVWR not GCWR Trailer lamps Trailer lamps are required on most towed vehicles Make sure your trailer lamps conform to local and Federal regulations See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps Driving while you tow When towing a trailer e Ensure that you turn off your speed control The speed control may shut off automatically when you are towing on long steep grades 132 Driving e Consult your local motor vehicle speed regulations for towing a trailer e Use a lower gear when towing up or down steep hills This will eliminate excessive downshifting and upshifting for optimum fuel economy and tra
103. ff feature 180 Maintenance and care When fueling your vehicle 1 Turn the engine off 2 Carefully turn the filler cap counterclockwise 1 8 of a turn until it stops 3 Pull to remove the cap from the fuel filler pipe 4 To install the cap align the tabs on the cap with the notches on the filler pipe 5 Turn the filler cap clockwise 1 8 of a turn until it stops If the Service Engine Soon Check Engine indicator comes on and stays on when you start the engine the fuel filler cap may not be properly installed Turn off the engine remove the fuel filler cap align the cap properly and reinstall it If you must replace the fuel filler cap replace it with a fuel filler cap that is designed for your vehicle The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used The fuel system may be under pressure If the fuel filler cap is venting vapor or if you hear a hissing sound wait until it stops before completely removing the fuel filler cap Otherwise fuel may spray out and injure you or others If you do not use the proper fuel filler cap excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel system to work improperly in a collision which may result in possible personal injury Choosing the right fuel Use only UNLEADED FUEL The use of leaded fuel is prohibited by law and could da
104. fter that CD play will begin where it stopped last Rewind The rewind control works in tape and CD modes REW e In tape mode radio play will 1 continue until rewind is stopped with the TAPE control or the beginning of the tape is reached e In CD mode pressing the REW control for less than three seconds results in slow rewind Pressing the control for more than three seconds results in fast rewind Fast forward The fast forward control works in tape and CD modes if equipped FF e In the tape mode tape direction 2 will automatically reverse when the end of the tape is reached 55 Controls and features e In CD mode pressing the control for less than three seconds results in slow forward action Pressing the control for more than three seconds results in fast forward action Tape direction select Press SIDE 1 2 to play the alternate side of a tape SIDE 1 2 Eject function Press the control to stop and eject a tape Dolby noise reduction Dolby noise reduction operates only in tape mode Dolby noise reduction reduces the amount of hiss and static during tape playback Press the D0 control to activate and deactivate Dolby noise reduction OL The Dolby noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation Dolby and the double D symbol are trademarks of Dolby Labratories Licensing Corporation Compression feature Compression adjust
105. g the rear brakes in conjunction with engine torque reductions Engine torque reduction is realized via the fully electronic spark and fuel injection systems This process is very sensitive to driving conditions and very fast acting The rear wheels search for optimum traction several times a second and adjustments are made accordingly The Traction Control system will allow your vehicle to make better use of available traction on slippery surfaces The system is a driver aid which makes your vehicle easier to handle primarily on snow and ice covered roads During Traction Control operation you may hear an electric motor type of sound coming from the engine compartment and the engine will not rev up when you push further on the accelerator This is normal system behavior If you should become stuck in snow or ice or on a very slippery road surface try switching the Traction Control system off This may allow excess wheel spin to dig the vehicle out and enable a successful rocking maneuver If the Traction Control system is cycled excessively the brake portion of the system will shut down to prevent the rear brakes from overheating A limited Traction Control function using only engine torque reduction will still control wheels from over spinning When the rear brakes have cooled down the system will again function normally Anti lock braking is not affected by this condition and will function normally during the co
106. ge to the transmission could occur Traction Conirol active if equipped Flashes when the Traction Control TRAC system begins applying and releasing the brakes and adjusting CNTL the engine characteristics to limit a wheelspin condition It will be lit for a minimum of four seconds or for the duration of the Traction Control event If the Traction Control indicator comes on or stays lit either e the Traction Control system needs service or e the customer has disabled the system using the traction control switch in the glove compartment For more information refer to the Driving chapter Message center indicator lights if equipped Speed control This light comes on when either the SET ACCEL or RESUME controls SPEED CO NTROL are pressed It turns off when the speed control OFF control is pressed the brake is applied or the ignition is turned to the OFF position 13 Instrumentation Door ajar Illuminates when one of the doors is not completely shut and the ignition is turned to ON With the ignition ON this light will flash five times and sound a tone for one second then remain on if a door is open Low washer fluid Momentarily illuminates when the ignition is turned to ON and will stay on when the windshield washer fluid is low Trunk ajar If the trunk is not completely closed this light comes on when you turn the ignition to ON With the ignition ON this light will flash five times
107. hat the seat is held securely in place If the child seat moves excessively repeat steps 5 through 6 or properly install the child seat in a different position Attaching child safety seats with tether straps lt Most new forward facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point Tether straps are available as an accessory for many older safety seats Contact the manufacturer of your child seat for information about ordering a tether strap The rear seats of your vehicle are equipped with built in tether strap anchors located behind the seats as described below The tether anchors in your vehicle are either located under a cover marked with the tether anchor symbol shown with title or are recessed bars on the back side of the seatback The tether strap anchors in your vehicle are in the following positions shown from top view Attach the tether strap only b to the appropriate tether anchor as shown The tether strap i T Lk may not work properly if attached somewhere other than the correct f tether anchor 115 Seating and safety restraints 1 Position the child safety seat on the passenger seat cushion 2 Route the child safety seat tether strap over the back of the seat For vehicles with adjustable head restraints route the tether strap under the head restraint and between the head restraint posts otherwise route the tether strap
108. he ON position The fuel gauge may vary slightly when the vehicle is in motion The ignition should be in the OFF position while the vehicle is being refueled When the gauge first indicates empty there is a small amount of reserve fuel in the tank When refueling the vehicle from empty indication the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel 15 Instrumentation e Standard instrument cluster e Optional instrument cluster A minimum of four gallons must be added or removed from the fuel tank in order for the gauge to instantaneously update If less than four gallons is added the gauge will take between five to ten minutes to update Speedometer Indicates the current vehicle speed e Standard instrument cluster 16 FUEL COILS BS 70 amp O50 5 80 0 0 0 0 0 0 m km h P RND21 Instrumentation e Optional instrument cluster 3 7mm i i __ km h Odometer Registers the total kilometers miles of the vehicle e Standard instrument cluster e Optional instrument cluster km h yj MPH I Refer to Electronic Message Center for information on how to switch the display from metric to English measurements 17 Instrumentation Trip odometer Registers the kilometers miles of individual journeys To reset depress the control
109. hen the ignition is turned to ON or START the theft indicator will light for three seconds and then go out If the theft indicator stays on for an extended period of time or flashes rapidly have the system serviced by your dealership or a qualified technician Programming spare SecuriLock keys Spare coded keys can be purchased from your dealership and programmed to your anti theft system up to a total of eight keys Your dealership can program your new coded key s to your vehicle or you can do it yourself using the following simple procedure To program a new coded key yourself you will need two previously programmed coded keys keys that already operate your vehicle s engine If two previously programmed coded keys are not available one or both of your original keys were lost or stolen you must bring your vehicle to your dealership to have the spare coded key s programmed Procedure to program spare SecuriLock keys to your vehicle New coded keys must have the correct mechanical key cut for your vehicle Conventional non coded keys cannot be programmed to your vehicle 85 Controls and features You will need to have two previously programmed coded keys and the new unprogrammed SecuriLock key readily accessible for timely implementation of each step in the procedure Please read and understand the entire procedure before you begin 1 Insert the first previously programmed coded key into the ignition and turn th
110. ical and will cool the inside of the vehicle faster Airflow is from the instrument panel registers This mode can also be used to prevent undesirable odors from entering the vehicle NORM A C Uses outside air to cool the vehicle The temperature display will remain the same and air will be cooled based on the selected temperature It is quieter than MAX A C but not as economical Fan speed will remain automatic Airflow is from the instrument panel registers VENT Distributes outside air through the instrument panel registers However the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode FLOOR Allows for maximum heating by distributing outside air through the floor ducts However the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode FLReDEF Distributes outside air through the windshield defroster ducts and the floor ducts Heating and air conditioning capabilities are provided in this mode The air will be heated or cooled based on the temperature selection For added customer comfort the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts If the temperature is about 10 C 50 F or higher the air conditioner will automatically dehumidify the air to reduce fogging DEF WY Distributes outside air through the windshield defroster ducts It can be used to
111. ign specifications start up engine noises or knock may be experienced It is recommended you use the appropriate Motorcraft oil filter or another brand meeting Ford specifications for your engine application 158 Maintenance and care BRAKE FLUID C Checking and adding brake fluid Brake fluid should be checked and refilled as needed Refer to the Scheduled Maintenance Guide for the service interval schedules 1 Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir 2 Visually inspect the fluid level 3 If necessary add brake fluid from a clean un opened container until the level reaches MAX Do not fill above this line 4 Use only brake fluids certified to meet Ford specifications Refer to Lubricant specifications in the Capacities and specifications chapter DOT 3 fluid is recommended However if DOT 3 is not available DOT 4 fluid can be used Brake fluid is toxic If brake fluid contacts the eyes flush eyes with running water for 15 minutes Seek medical attention if irritation persists If taken internally drink water and induce vomiting Seek medical attention immediately If you use DOT 5 or any other brake fluid that is not DOT 3 or DOT 4 you will cause permanent damage to your brakes Do not let the reservoir for the master cylinder run dry this may cause the brakes to fail 159 Maintenance and care WINDSHIELD WASHER FLUID lt 7 Checking a
112. ildup inside the vehicle don t drive with the climate control system in the OFF position Don t put objects under the front seat that will interfere with the airflow to the back seats 33 Controls and features Remove any snow ice or leaves from the air intake area at the bottom of the windshield If your vehicle has been parked with the windows closed during hot weather the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open This will force most of the hot stale air out of the vehicle Then operate the air conditioner as you would normally Do not place objects over the defroster outlets These objects can block airflow and reduce your ability to see through your windshield Also avoid placing small objects on top of your instrument panel These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop CLOCK Press H to set the hour Press M to set the minute The auxiliary power point is located under the instrument panel on the left hand side of the front passenger foot well This outlet should be used in place of the cigarette lighter for optional electrical accessories 34 Controls and features USING YOUR AUDIO SYSTEM AM FM Stereo
113. ion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child s face or neck the child should wear the lap and shoulder belt Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit Do not leave children unreliable adults or pets unattended in your vehicle To improve the fit of lap and shoulder belts on children who have outgrown child safety seats Ford recommends use of a belt positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards Belt positioning booster seats raise the child and provide a shorter firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child 110 Seating and safety restraints A belt positioning booster should be used if the shoulder belt rests in front of the child s face or neck or if the lap belt does not fit snugly on both thighs or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion You may wish to discuss the special needs of your child with your pediatrician SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child Carefully follow all of the manufacturer s instructions with the safety seat you put in your vehicle If you do no
114. ir safety belts even when an air bag SRS is provided 105 Seating and safety restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints National Highway Traffic Safety Administration NHTSA recommends a minimum distance of at least 25 cm 10 inches between an occupant s chest and the driver air bag module Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries Steps you can take to properly position yourself away from the air bag e Move your seat to the rear as far as you can while still reaching the pedals comfortably e Recline the seat slightly one or two degrees from the upright position Do not put anything on or over the air bag module Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury Do not attempt to service repair or modify the Air Bag Supplemental Restraint System or its fuses See your Ford or Lincoln Mercury dealer Modifications to the front end of the vehicle including frame bumper front end body structure and tow hooks may effect the performance of the air bag sensors increasing the risk of injury Do not modify the front end of the vehicle 106 Seating and safety restraints Children and air bags For additional important safety information r
115. ith the wheels out of alignment will reduce fuel economy Use recommended engine oil Refer to Lubricant Specifications Perform all regularly scheduled maintenance items Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle Scheduled Maintenance Guide Conditions Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed 185 Maintenance and care Carrying unnecessary weight may reduce fuel economy approximately 0 4 km L 1 mpg is lost for every 180 kg 400 lb of weight carried e Adding certain accessories to your vehicle for example bug deflectors rollbars light bars running boards ski luggage racks may reduce fuel economy Using fuel blended with alcohol may lower fuel economy e Fuel economy may decrease with lower temperatures during the first 12 16 km 8 10 miles of driving Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain e Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal e Close windows for high speed driving EPA window sticker Every new vehicle should have the EPA window sticker Contact your dealer if the window sticker is not supplied with your vehicle The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles It is important to note the box in the lower left corner of the
116. k AM FM stereo cassette VOL PUSH ON OG 38 Controls and features Volume power control Press the control to turn the audio VOL PUSH ON system on or off O Turn the control to raise or lower volume x K VOL PUSH ON If the volume is set above a certain level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition switch is turned back on AM FM select The AM FM select control works in radio and tape modes AM FM select in radio mode This control allows you to select AM or FM frequency bands Press the AM control to select from AM selections and press the FM control to select from FM1 or FM2 memory preset stations AM FM select in tape mode Press this control to stop tape play and begin radio play 39 Controls and features Tune adjust The tune control works in radio mode Tune adjust in radio mode e Press lt q to move to the next frequency down the band whether or not a listenable station is located there Hold the control to move through the frequencies quickly e Press gt to move to the next frequency up the band whether or not a listenable station is located there Hold for quick movement Seek function The seek function control works in radio mode Seek function in radio mode e Press A to find the next listenable station down the frequency band e Press to
117. ket and slide the ring off the plastic base Keep the ring to retain the new bulb 5 Without turning remove the old bulb from the lamp assembly by gently pulling it straight back out of the lamp assembly To install the new bulb Handle a halogen headlamp bulb carefully and keep out of children s reach Grasp the bulb only by its plastic base and do not touch the glass The oil from your hand could cause the bulb to break the next time the headlamps are operated 1 With the flat side of the new bulb s plastic base facing upward insert the glass end of the bulb into the lamp assembly Turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly When the grooves are aligned push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly 2 Install the bulb retaining ring over the plastic base until it contacts the rear of the socket by rotating it clockwise until you feel a stop 3 Connect the electrical connector into the rear of the plastic base until it snaps locking it into position 4 Install the protective cover over headlamps locking it in place with three knobs 189 Maintenance and care 5 Turn the headlamps on and make sure they work properly If the headlamp was correctly aligned before you changed the bulb you should not need to align it again Replacing front parking lamp turn signal bulbs The park turn lamp
118. ld safety seats in combination lap and shoulder belt seating positions 1 Position the child safety seat in a seat with a combination lap and shoulder belt An air bag can kill or injure a child in a child seat If you must use a forward facing child seat in the front seat move seat all the way back Children 12 and under should be properly restrained in the rear seat whenever possible 112 Seating and safety restraints 2 Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together 3 While holding the shoulder and lap belt portions together route the tongue through the child seat according to the child seat manufacturer s instructions Be sure the belt webbing is not twisted 4 Insert the belt tongue into the proper buckle the buckle closest to the direction the tongue is coming from for that seating position until you hear a snap and feel the latch engage Make sure the tongue is latched securely by pulling on it 113 Seating and safety restraints 5 To put the retractor in the automatic locking mode grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard e 6 Allow the belt to retract The belt will click as it retracts to indicate it is in the automatic locking mode 7 Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your kne
119. ldren Also see Air Bag Supplemental Restraint System SRS in this chapter for special instructions about using air bags 109 Seating and safety restraints Important child restraint precautions You are required by law to use safety restraints for children in the U S and Canada If small children ride in your vehicle generally children who are four years old or younger and who weigh 18 kg 40 Ibs or less you must put them in safety seats made especially for children Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision Always follow the instructions and warnings that come with any infant or child restraint you might use When possible always place children under age 12 in the rear seat of your vehicle Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position Children and safety belts If the child is the proper size restrain the child in a safety seat Children who are too large for child safety seats as specified by your child safety seat manufacturer should always wear safety belts Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle If the shoulder belt port
120. ly locks all doors when e all vehicle doors are closed e the ignition is in the ON position e you shift into R Reverse or D Drive Relock The autolock feature repeats when e any door is opened and closed e the brake pedal is released Deactivating activating the autolock feature Before following the procedure make sure that the ignition is OFF and all vehicle doors are closed 80 Controls and features Automatic door locks can be turned on off with the keyless entry keypad through the following procedure You must complete steps 1 5 within 30 seconds or the procedure will have to be repeated If the procedure needs to be repeated you must wait 30 seconds 1 Enter the keyless entry keypad factory code 2 Within 5 seconds press and hold control 7 8 3 Within 5 seconds while holding down control 7 8 press and release control 3 4 4 Release control 7 8 The door will lock unlock to confirm the feature has been disabled Once disabled the feature can be enabled by repeating the same sequence Automatic door locks can also be turned on off through the following procedure You must complete steps 1 7 within 30 seconds or the procedure will have to be repeated If the procedure needs to be repeated you must wait 30 seconds 1 Turn the ignition key to ON Press the power door unlock control on the door panel three times Turn the ignition key from ON to OFF Press the power door unlock control th
121. mage your vehicle Do not use fuel containing methanol It can damage critical fuel system components Your vehicle was not designed to use fuel or fuel additives with metallic compounds including manganese based compounds containing MMT Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty 181 Maintenance and care Octane recommendations Your vehicle is designed to use Regular unleaded gasoline with an R M 2 octane rating of 87 We do not recommend the use of gasolines labeled as Regular that are sold with octane ratings of 86 or lower in high altitude areas Do not be concerned if your engine sometimes knocks lightly However if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating see your dealer or a qualified service technician to prevent any engine damage Fuel quality If you are experiencing starting rough idle or hesitation driveability problems during a cold start try a different brand of Regular unleaded gasoline Premium unleaded gasoline is not recommended particularly in the United States because it may cause these problems to become more pronounced If the problems persist see your dealer or a qualified service technician It should not be necessary to add any aftermarket products to your fuel tank if you continue to use high quality fuel of the recommend
122. mains illuminated with parking brake released If your brake warning lamp illuminates have your vehicle serviced immediately Using ABS e In an emergency or when maximum efficiency from the ABS is required apply continuous force on the brake The ABS will be activated immediately thus allowing you to retain full steering control of your vehicle and providing there is sufficient space will enable you to avoid obstacles and bring the vehicle to a controlled stop e The Anti Lock system does not decrease the time necessary to apply the brakes or always reduce stopping distance Always leave enough room between your vehicle and the vehicle in front of you to stop e We recommend that you familiarize yourself with this braking technique However avoid taking any unnecessary risks Parking brake with auto release P Apply the parking brake whenever the vehicle is parked To set the parking brake 1 Move the gearshift to P Park 2 Push pedal downward 122 Driving The BRAKE warning lamp in the instrument cluster illuminates and BRAKE remains illuminated when the ignition is turned ON until the 1 P parking brake is fully released Always set the parking brake fully and make sure the gearshift is latched in P Park Turn off the ignition whenever you leave your vehicle The parking brake is not recommended to stop a moving vehicle However if the normal brakes fail the parking brake can be used to stop yo
123. mation Indicates that this Owner Guide contains information on this subject Please refer to the Index to locate Lil the appropriate section which will provide you more information Introduction WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others your vehicle and its equipment BREAKING IN YOUR VEHICLE There are no particular breaking in rules for your vehicle During the first 1 600 km 1 000 miles of driving vary speeds frequently This is necessary to give the moving parts a chance to break in INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing Ford may change the contents without notice and without incurring obligation SPECIAL NOTICES Notice to owners of Severe Duty vehicles Before you drive your vehicle be sure to read the Severe Duty Owner s Guide Supplement This book contains important operation and maintenance information Notice to owners of natural gas fueled vehicles Before you drive your vehicle be sure to read the Natural Gas Vehicle Owner s Guide Supplement This book contains important operation and maintenance information Introduction These are some of the symbols you may see on your vehicle Vehicle Symbol Glossary Safety Alert Fasten Safety Belt Air Bag Side Child Seat Installation Warning Brake System Brake Fluid Non Petroleum
124. mber to figure in the tongue load of your loaded trailer when figuring the total weight Do not exceed the GVWR or the GAWR specified on the certification label Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle s GVWR and GAWR 130 Driving limitations Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations The Certification Label found on the inside pillar of the driver s door lists several important vehicle weight rating limitations Before adding any additional equipment refer to these limitations If you are adding weight to the front of your vehicle potentially including weight added to the cab the weight added should not exceed the front axle reserve capacity FARC Additional frontal weight may be added to the front axle reserve capacity provided you limit your payload in other ways i e restrict the number of passengers or amount of cargo carried You may add equipment throughout your vehicle if the total weight added is equal to or less than the total axle reserve capacity TARC weight You should NEVER exceed the total axle reserve capacity Always ensure that the weight of passengers cargo and equipment being carried is within the weight limitations that have been established for your vehicle including both gross vehicle weight and front and rear gross axle weight rating limits Under no circums
125. minal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575 104 c 2 U S Department of Transportation Tire quality grades The U S Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it 174 Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course For example a tire graded 150 would wear one and one half 1 1 2 times as well on the government course as a tire graded 100 The relative performance of tires depends upon the actual conditions of their use however and may depart significantly from the norm due to variations in driving habits service practices and differences in road characteristics and climate Traction AAA BC The traction grades from highest to lowest are AA A B and C Those grades represent the tire s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance The traction grade assigned to this tire is based on straight ahead braking traction tests and does not include acceleration cornering hydroplaning or peak traction characteristics Temperature A B C The temperature grades are A the high
126. ms may result in vehicle starting problems and a loss of security protection Large metallic objects electronic devices on the key chain that can be used to purchase gasoline or similar items or a second key on the same key ring as the PATS ignition key may cause vehicle starting concern and record DTC s under certain conditions If present you need to keep these objects from touching the PATS ignition key while starting the engine These objects 84 Controls and features and devices cannot damage the PATS ignition key but can cause a momentary concern if they are too close to the key during engine start If a problem occurs turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key Check to make sure the encoded ignition key is an approved Ford encoded ignition key Spare coded keys can be purchased from your dealership and programmed to your anti theft system Refer to Programming spare SecuriLock keys for more information If one or both of your coded keys are lost or stolen and you want to ensure the lost or stolen key will not operate your vehicle bring your vehicle and all available coded keys to your dealership for reinitialization Theft indicator The theft indicator in the instrument cluster will operate as follows e When the ignition is OFF the theft indicator will flash briefly every two seconds to indicate the anti theft system is protecting your vehicle e W
127. n may occur 2 f when e front wheels are turned Gy e front wheel is against the curb e steering wheel is turned when getting in or out of the vehicle E check O OPIATE CHECK AIR SUSPENSION DOOR sE A ENGINE HHHH L OVERDRIVE OFF AJAR SPEED CONTROL km h SRD EA H m m F O y4 MPH LOW 0 a a AR FLUID ti GAL uo a a gt TRUNK AJAR LTR 100 km 0 au 1 A DISTANCE AVG FUEL R m TO EMPTY ECONOMY M i 3P J TBP CAS 7 eal Cc D SEM PRNO21 Make sure the corresponding lights illuminate briefly If a light fails to illuminate have the vehicle serviced e If the driver s safety belt is fastened the A light may not illuminate 118 Starting STARTING THE ENGINE 1 Turn the key to 5 START lt without pressing the accelerator pedal and release as soon as the G 4 engine starts The key will return to 4 ON 2 If the temperature is above 12 C 10 F and the engine does not start within five seconds on the first try turn the key to OFF wait 10 seconds and try again Ne 3 If the temperature is below 12 C 10 F and the engine does not start in 15 seconds on the first try turn the key OFF and wait 10 seconds and try again If the engine does not start in two attempts Press the accelerator pedal all the way to floor and hold Turn the key to START position 4 When the engine starts release the key then release the accelerator
128. n your vehicle The tires on your vehicle have all weather treads to provide traction in rain and snow However in some climates you may need to use snow tires and chains If you need to use chains it is recommended that steel wheels of the same size and specifications be used as chains may chip aluminum wheels Follow these guidelines when using snow tires and chains e Use only SAE Class S chains e Install chains securely verifying that the chains do not touch any wiring brake lines or fuel lines Drive cautiously If you hear the chains rub or bang against your vehicle stop and re tighten the chains If this does not work remove the chains to prevent damage to your vehicle If possible avoid fully loading your vehicle Remove the tire chains when they are no longer needed Do not use tire chains on dry roads e The suspension insulation and bumpers will help prevent vehicle damage Do not remove these components from your vehicle when using snow tires and chains WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS wp Important safety precautions Do not overfill the fuel tank The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire 178 Maintenance and care The fuel system may be under pressure If the fuel filler cap is venting vapor or if you hear a hissing sound wait until it stops before completely removing the fuel filler cap Otherwise fuel may spray out and injure you or others
129. nd adding washer fluid Check the washer fluid whenever you stop for fuel The reservoir is highlighted with a symbol If the level is low add enough fluid to fill the reservoir In very cold weather do not fill the reservoir all the way Only use a washer fluid that meets Ford specifications Refer to Lubricant specifications in the Capacities and specifications chapter State or local regulations on volatile organic compounds may restrict the use of methanol a common windshield washer antifreeze additive Washer fluids containing non methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle s paint finish wiper blades or washer system Do not put washer fluid in the engine coolant reservoir Washer fluid placed in the cooling system may harm engine and cooling system components ENGINE COOLANT E Checking engine coolant Your engine s cooling system has been factory filled with a 50 50 mixture of distilled water and Ford Premium Engine Coolant E2FZ 19549 AA in Canada Motorcraft CXC 10 or an equivalent premium engine coolant that meets Ford specification ESE M97B44 A A 50 50 mixture of distilled water and Ford Premium Engine Coolant provides e maximum cooling system efficiency e freeze protection down to 36 C 34 F e boiling protection up to 129 C 265 F 160 Maintenance and care e protection against rust and other forms of
130. nd pulsation in the pedal may be observed during ABS braking events Pedal pulsation coupled with noise while braking under panic conditions or on loose gravel bumps wet or snowy roads is normal and indicates proper functioning of the vehicle s anti lock brake system The ABS performs a self check after you start the engine and begin to drive away A brief mechanical noise may be heard during this test This is normal If a malfunction is found the ABS warning light will come on If the vehicle has continuous vibration or shudder in the steering wheel while braking the vehicle should be inspected by a qualified service technician The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency The wheels are prevented from locking even when the brakes are firmly applied The accompanying illustration depicts the advantage of an ABS equipped vehicle on bottom to a non ABS equipped vehicle on top during hard braking with loss of front braking traction 121 Driving ABS warning lamp s The 3 warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position If the light does not illuminate momentarily at start up remains on or continues to flash the ABS needs to be serviced With the ABS light on the anti lock brake system is disabled and normal O braking is still effective unless the BRAKE brake warning light also re
131. ng summer and winter will show how temperature impacts fuel economy In general lower temperatures give lower fuel economy Driving style good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy 184 Maintenance and care Habits Smooth moderate operation can yield up to 10 savings in fuel Steady speeds without stopping will usually give the best fuel economy Idling for long periods of time greater than one minute may waste fuel Anticipate stopping slowing down may eliminate the need to stop Sudden or hard accelerations may reduce fuel economy Slow down gradually Driving at reasonable speeds traveling at 88 km h 55 mph uses 15 less fuel than traveling at 105 km h 65 mph Revving the engine before turning it off may reduce fuel economy Using the air conditioner or defroster may reduce fuel economy You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs Unnecessary shifting of this type could result in reduced fuel economy Warming up a vehicle on cold mornings is not required and may reduce fuel economy Resting your foot on the brake pedal while driving may reduce fuel economy Combine errands and minimize stop and go driving Maintenance Keep tires properly inflated and use only recommended size Operating a vehicle w
132. nsmission cooling e Anticipate stops and brake gradually Exceeding the GCWR rating may cause internal transmission damage and void your warranty coverage Servicing after towing If you tow a trailer for long distances your vehicle will require more frequent service intervals Refer to your Scheduled Maintenance guide for more information Trailer towing tips e Practice turning stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination When turning make wider turns so the trailer wheels will clear curbs and other obstacles e Allow more distance for stopping with a trailer attached e The trailer tongue weight should be 10 of the loaded trailer weight e After you have traveled 80 km 50 miles thoroughly check your hitch electrical connections and trailer wheel lug nuts e When stopped in traffic for long periods of time in hot weather place the gearshift in P Park and increase idle speed This aids engine cooling and air conditioner efficiency e Vehicles with trailers should not be parked on a grade If you must park on a grade place wheel chocks under the trailer s wheels Launching or retrieving a boat When backing down a ramp during boat launching or retrieval e Do not allow the static water level to rise above the bottom edge of the rear bumper and e Do not allow waves to break higher than 15 cm 6 inches above the bottom edge of the rear bumper E
133. ntrol Controls the volume of air circulated Lo s in the vehicle TY HI Temperature control knob Controls the temperature of the airflow inside the vehicle P Mode selector control Controls the direction of the airflow ae o to the inside of the vehicle wont TY u Ww The air conditioning compressor will operate in all modes except VENT and FLR However the air conditioning will only function if the outside temperature is about 10 C 50 F or higher 26 Controls and features Since the air conditioner removes considerable moisture from the air during operation it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle MAX A C Uses recirculated air to cool the vehicle MAX A C is noisier than NORM A C but more economical and will cool the inside of the vehicle faster Airflow will be from the instrument panel registers This mode can also be used to prevent undesirable odors from entering the vehicle NORM A C Uses outside air to cool the vehicle It is quieter than MAX A C but not as economical Airflow will be from the instrument panel registers VENT Distributes outside air through the instrument panel registers However the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode OFF Outside air is shut out and the fan will not operate For short periods of
134. nts The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning including the impact sensors the system wiring the air bag system readiness light the air bag back up power and the air bag ignitors Determining if the system is operational at The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system Refer to the Air bag readiness section in the Instrumentation chapter Routine maintenance of the air bag is not required A difficulty with the system is indicated by one or more of the following e The readiness light will either AIR flash or stay lit BAG e The readiness light will not illuminate immediately after ignition is turned on A series of five beeps will be heard The tone pattern will repeat periodically until the problem and light are repaired If any of these things happen even intermittently have the SRS serviced at your dealership or by a qualified technician immediately Unless serviced the system may not function properly in the event of a collision Disposal of air bags and air bag equipped vehicles including pretensioners For disposal of air bags or air bag equipped vehicles see your local dealership or qualified technician Air bags MUST BE disposed of by qualified personnel SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for chi
135. nts contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time open the windows at least 2 5 cm one inch Adjust the heating or air conditioning Gif equipped to bring in fresh air Improve vehicle ventilation by keeping all air inlet vents clear of snow leaves and other debris 120 Driving BRAKES Your service brakes are self adjusting Refer to the scheduled maintenance guide for scheduled maintenance Occasional brake noise is normal and often does not indicate a performance concern with the vehicle s brake system In normal operation automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied Such noises are usually heard during the first few brake applications in the morning however they may be heard at any time while braking and can be aggravated by environmental conditions such as cold heat moisture road dust salt or mud If a metal to metal continuous grinding or continuous squeal sound is present while braking the brake linings may be worn out and should be inspected by a qualified service technician Anti lock brake system ABS if equipped On vehicles equipped with an anti lock braking system ABS a noise from the hydraulic pump motor a
136. ode while in radio mode press the TAPE AMS control Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection To activate the feature momentarily depress the TAPE AMS button Then press either REW for the beginning of the current selection or FF to advance to the next 42 Controls and features selection The tape deck stops and returns to play mode when the AMS circuit senses a blank section on the tape In order to ensure proper operation of the AMS feature the tape MUST have a blank section of at least four seconds duration between programs Rewind The rewind control works in tape mode To rewind in tape mode press the REW control Fast forward The fast forward control works in tape mode e In the tape mode tape direction will automatically reverse when the end of the tape is reached Tape direction select Press SIDE and 1 2 at the same time to play the alternate side of a tape Eject function Press the control to stop and eject a tape Dolby noise reduction Dolby noise reduction operates only in tape mode Dolby noise reduction reduces the amount of hiss and static during tape playback Press the BO control to activate and deactivate Dolby noise reduction Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Cor
137. ographic areas zones have a magnetic north compass point that varies slightly from the northerly direction on maps This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones A correct zone setting will eliminate this error Refer to Compass zone adjustment 73 Controls and features Compass zone adjustment 1 Determine which compass zone you are in by referring to the zone map 2 With the compass display turned on press and hold the COMP side of the control for no more than six seconds until the zone selection number appears in the mirror display window If a C appears repeat this step 3 Release the COMP side of the control then press it down again 4 Continue to press until your zone number is shown in the mirror display then release 5 The display will show all segments then return to normal compass mode within ten seconds Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines 1 Start the vehicle 74 2 Press and hold the COMP side of the control for approximately six seconds until C appears in the mirror display 3 Drive the vehicle slowly less than 5 km h 8 mph in circles or on your everyday routine until the display reads a direction 4 The compass is now calibrated TRUNK REMOTE CONTROL The remote trunk release control is located
138. ol down period The traction control indicator TRAC flashes during a Traction Control system event CNTL If the traction control indicator comes on and stays lit either e the Traction Control system requires service or e the customer has disabled the system using the traction control switch located on the left side of the glove compartment 124 Driving The Traction Control system will be on every time you turn the ignition key from OFF to ON until you deactivate the system using the traction control switch in the glove compartment STEERING Your vehicle is equipped with power steering Power steering uses energy from the engine to help steer the vehicle To prevent damage to the power steering pump e Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running e Do not operate the vehicle with a low power steering pump fluid level If the power steering system breaks down or if the engine is turned off you can steer the vehicle manually but it takes more effort If the steering wanders or pulls the condition could be caused by any of the following e underinflated tire s on any wheel s e high crown in center of road e high crosswinds e wheels out of alignment e loose or worn components in steering linkage Speed sensitive steering except police vehicles The steering in your vehicle is speed sensitive At high speeds steering
139. ol in heavy traffic or on roads that are winding slippery or unpaved To set a higher set speed Press and hold SET SET ACC SET ACCEL Release the control when the desired vehicle speed is reached or Press and release SET SET ACC SET ACCEL Each press will increase the set speed by 1 6 km h 1 mph or Accelerate with your accelerator pedal When the desired vehicle speed is reached press and release SET SET ACC SET ACCEL DS You can accelerate with the accelerator pedal at any time during speed control usage Releasing the accelerator pedal will return your vehicle to the previously programmed set speed To set a lower set speed Press and hold CST COAST Release the control when the desired speed is reached or Press and release CST COAST Each press will decrease the set speed by 1 6 km h 1 mph or TAN 67 Controls and features e Depress the brake pedal When the desired vehicle speed is reached press SET SET ACC SET ACCEL To disengage speed control e Depress the brake pedal Disengaging the speed control will not erase the previously programmed set speed Pressing OFF will erase the previously programmed set speed 68 Controls and features To return to a previously set speed e Press RES RSM RESUME For RES RSM RESUME to operate the vehicle speed must be faster than 48 km h 30 mph Indicator light if equipped This light h ither th SET ACC SET ACCEL or REVRSW SPEED
140. ol in the direction A you wish to tilt the mirror 3 Return to the center position to lock mirrors in place CHILDPROOF DOOR LOCKS When these locks are set the rear doors cannot be opened from the ax inside The rear doors can be i opened from the outside when the N doors are unlocked The childproof locks are located on rear edge of each rear door and must be set separately for each door Setting the lock for one door will not automatically set the lock for both doors Move lock control up to engage the childproof lock Move control down to disengage childproof locks POSITIVE RETENTION FLOOR MAT Position the floor mat so that the A eyelet is over the pointed end of the retention post and rotate forward to T lock in Make sure that the mat does not interfere with the operation of l the accelerator or the brake pedal To remove the floor mat reverse the installation procedure PT 78 Controls and features REMOTE ENTRY SYSTEM IF EQUIPPED The remote entry system allows you to lock or unlock all vehicle doors without a key The remote entry features only operate with the ignition in the OFF position If there is any potential remote keyless entry problem with your vehicle ensure ALL key fobs remote entry transmitters are brought to the dealership to aid in troubleshooting Unlocking the doors Press this control to unlock the driver s door The interior lamps will illuminate Pre
141. on does not qualify for Board review Oral presentations If you would like to make an oral presentation indicate YES to question 6 on the application While it is your right to make an oral presentation before the Board this is not a requirement and the Board will decide the case whether or not an oral presentation is made Oral presentation may be requested by the Board as well Making a decision Board members review all available information related to each complaint including oral presentations and arrive at a fair and impartial decision Board review may be terminated at any time by either party Every effort is made to decide the case within 40 days of the date that all requested information is received by the Board Since the Board generally meets once a month it may take longer for the Board to consider some cases After a case is reviewed the Board mails you a decision letter and a form on which to accept or reject the Board s decision The decisions of the Board are binding on Ford and in some cases on the dealer but not on consumers who are free to pursue other remedies available to them under state or federal law To Request a DSB Brochure Application For a brochure application speak to your dealer or write call to the Board at the following address phone number Dispute Settlement Board P O Box 5120 Southfield MI 48086 5120 1 800 428 3718 211 Customer assistance You may also contact the North
142. ong detergents Never use abrasives that will damage the finish of special wheel surfaces Use a tar remover to remove grease and tar The brushes used in some automatic car washes may damage the finish on your wheels Before going to a car wash find out if the brushes are abrasive Cleaning non painted plastic exterior parts Use vinyl cleaner for routine cleaning Clean with a tar remover if necessary Do not clean plastic parts with thinners solvents or petroleum based cleaners Underbody Flush the complete underside of vehicle frequently Keep body drain holes unplugged Inspect for road damage Cleaning mirrors Do not clean your mirrors with a dry cloth or abrasive materials Use a soft cloth and mild detergent and water Be careful when removing ice from outside mirrors because you may damage the reflective surface Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle If necessary use a tar remover such as Ford Extra Strength Tar and Road Oil Remover B7A 19520 AA 195 Maintenance and care To avoid scratching the lamps do not use a dry paper towel chemical solvents or abrasive cleaners Cleaning the wiper blades windshield and rear window If the wiper blades do not wipe properly clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent To avoid damaging the blades do not use fuel kerosene paint thinner or other solvents If the
143. ound 2 Turn the engine off and wait a few minutes for the oil to drain into the oil pan 3 Set the parking brake and ensure the gearshift is securely latched in P Park 4 Open the hood Protect yourself from engine heat 5 Locate and carefully remove the engine oil level indicator dipstick 6 Wipe the indicator clean Insert the indicator fully then remove it again 156 Maintenance and care e If the oil level is within this range the oil level is acceptable DO NOT ADD OIL Sa Serererererecerd PSSSPSLSCSES SSS RSssssssomax 3 ni _ eee tet 0 OK 650505 KES 0 DO NOT OVERFILL e If the oil level is below this mark engine oil must be added to raise the level within the normal operating range A XXXL ORO L O RRRS o DO NOT OVERFILL e If required add engine oil to the engine Refer to Adding engine owl in this chapter e Do not overfill the engine with oil Oil levels above this mark may cause engine damage If the engine is overfilled some oil must be removed from the engine by a __ FEE o DONOTOVERLL qualified service technician PMN 7 Put the indicator back in and ensure it is fully seated Adding engine oil 1 Check the engine oil For instructions refer to Checking the engine oil in this chapter 2 If the engine oil level is not within the normal operating range add only certified engine oil of the recommended viscosity Remov
144. over the top of the seatback 3 Locate the correct anchor for the selected seating position f AN 4 Open the tether anchor cover 5 Clip the tether strap to the anchor as shown If the tether strap is clipped incorrectly the child safety seat may not be retained properly in the event of a collision 6 Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat 7 Tighten the child safety seat tether strap according to the manufacturer s instructions If the safety seat is not anchored properly the risk of a child being injured in a collision greatly increases 116 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system This system meets all Canadian Interference Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise When starting a fuel injected engine avoid pressing the accelerator before or during starting Only use the accelerator when you have difficulty starting the engine For more information on starting the vehicle refer to Starting the engine in this chapter Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system creating the risk of fire or other damage Do not park idle or drive your vehicle in dry grass or other dry gro
145. ow 40 e decreased engine coolant concentrations below 40 will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage e decreased engine coolant concentrations below 40 will decrease the freeze protection characteristics of the engine coolant and may cause engine damage e refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive Vehicles driven year round in non extreme climates should use a 50 50 mixture of engine coolant and distilled water for optimum cooling system and engine protection What you should know about fail safe cooling If the engine coolant supply is depleted this feature allows the vehicle to be driven temporarily before incremental component damage is incurred The fail safe distance depends on ambient temperatures vehicle load and terrain 164 Maintenance and care How fail safe cooling works e Standard cluster e Optional cluster zvoz ap If the engine begins to overheat e the engine coolant temperature gauge will move to the H hot area Gf your vehicle is equipped with analog gauges e the engine coolant temperature gauge will illuminate all eight bars and a tone will sound every five seconds for one minute if your vehicle is equipped with digital gauges e the E symbol will illuminate e the Check Engine indicator
146. owder to lubricate the bag or sodium compounds e g baking soda that result from the combustion process that inflates the air bag Small amounts of sodium hydroxide may be present which may irritate the skin and eyes but none of the residue is toxic While the system is designed to help reduce serious injuries contact with a deploying air bag may also cause abrasions swelling or temporary hearing loss Because air bags must inflate rapidly and with considerable force there is the risk of death or serious injuries such as fractures facial and eye injuries or internal injuries particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment Thus it is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control Several air bag system components get hot after inflation Do not touch them after inflation If the air bag is deployed the air bag will not function again and must be replaced immediately If the air bag is not replaced the unrepaired area will increase the risk of injury in a collision The SRS consists of e driver and passenger air bag modules which include the inflators and air bags e one or more impact and safing sensors e a readiness light and tone e diagnostic module 108 Seating and safety restraints e and the electrical wiring which connects the compone
147. p Pull down on the height adjuster to make sure it is locked in place Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision Lap belts Adjusting the lap belt The lap belt does not adjust automatically The lap belts should fit snugly and as low as possible around the hips not around the waist 99 Seating and safety restraints Insert the tongue into the correct buckle the buckle closest to the direction the tongue is coming from To lengthen the belt turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle To tighten the belt pull the loose end of the belt through the tongue until it fits snugly across the hips Shorten and fasten the belt when not in use Safety belt extension assembly If the safety belt assembly is too short even when fully extended 20 cm 8 inches can be added to the safety belt assembly by adding a safety belt extension assembly part number 611C22 Safety belt extension assemblies can be obtained from your dealer at no cost Use only extensions manufactured by the same supplier as the safety belt Manufacturer identification is located at the end of the webbing on the label Also use the safety belt extension only if the safety belt is too short for
148. perators Have your tow truck operator refer to this manual for proper hook up and towing procedures for your vehicle 152 Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle e We highlight do it yourself items in the engine compartment for easy location e We provide a Scheduled Maintenance Guide which makes tracking routine service easy If your vehicle requires professional service your dealership can provide necessary parts and service Check your Warranty Guide to find out which parts and services are covered Use only recommended fuels lubricants fluids and service parts conforming to specifications Motorcraft parts are designed and built to provide the best performance in your vehicle PRECAUTIONS WHEN SERVICING YOUR VEHICLE Be especially careful when inspecting or servicing your vehicle e Do not work on a hot engine e When the engine is running keep loose clothing jewelry or long hair away from moving parts e Do not work on a vehicle with the engine running in an enclosed space unless you are sure you have enough ventilation e Keep all lit cigarettes open flames and other lit material away from the battery and all fuel related parts If you disconnect the battery the engine must relearn its idle conditions before your vehicle will drive properly as explained in the Battery section in this chapter 153 Maintenance and care Working with the engine off 1
149. poration Dolby and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation 43 Controls and features Setting the clock Your vehicle is equipped with a separate instrument panel mounted clock Please refer to Clock in this chapter for instructions on setting the clock AM FM Siereo Single CD Radio VOL PUSH ON OGE 3s EES V osc V DEG O00000 Volume power control Press the control to turn the audio VOL PUSH ON system on or off C O N Turn the control to raise or lower K N volume VOL PUSH ON 44 Controls and features If the volume is set above a certain level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition switch is turned back on AM FM select The AM FM select control works in radio and CD modes AM FM select in radio mode This control allows you to select AM or FM frequency bands Press the control to switch between AM FM1 or FM2 memory preset stations AM FM select in CD or CD changer mode if equipped Press this control to stop CD play and begin radio play Tune adjust The tune control works in radio mode Tune adjust in radio mode e Press lt q to move to the next frequency down the band whether or not a listenable station is located there Hold the control to move through the frequencies quickly e Press gt to mov
150. r CAMVAP Provincial Administrator directly at 1 800 207 0685 GETTING ASSISTANCE OUTSIDE THE U S AND CANADA Before exporting your vehicle to a foreign country contact the appropriate foreign embassy or consulate These officials can inform you of local vehicle registration regulations and where to find unleaded fuel If you cannot find unleaded fuel or can only get fuel with an anti knock index lower than is recommended for your vehicle contact a district or owner relations customer assistance office 212 Customer assistance The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage Ford Motor Company Ford of Canada is not responsible for any damage caused by use of improper fuel In the United States using leaded fuel may also result in difficulty importing your vehicle back into the U S If your vehicle must be serviced while you are traveling or living in Central or South America the Caribbean or the Middle East contact the nearest Ford dealership If the dealership cannot help you write or call FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park 3 Allen Park Michigan 48101 U S A Telephone 313 594 4857 FAX 313 390 0804 If you are in another foreign country contact the nearest Ford dealership If the dealership employees cannot help yo
151. r blades using undiluted windshield wiper solution or a mild detergent Rinse thoroughly with clean water To avoid damaging the blades do not use fuel kerosene paint thinner or other solvents Changing the wiper blades To make changing the wiper blades easy turn the ignition to ACC then turn the wipers on When the wipers reach the vertical position turn the ignition to LOCK 173 Maintenance and care To replace the wiper blades 1 Pull the wiper arm away from the windshield and lock into the service position 2 Turn the blade at an angle from the wiper arm Push the lock pin gt manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm 3 Attach the new wiper to the wiper arm and press it into place until a click is heard INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width For example e Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set Tire Quality Grades apply to new pneumatic tires for use on passenger cars They do not apply to deep tread winter type snow tires space saver or temporary use spare tires tires with no
152. r that service but you may also take your vehicle to another Ford Motor Company dealership authorized for warranty repairs Certain warranty repairs require special training though so not all dealers are authorized to perform all warranty repairs That means that depending on the warranty repair needed the vehicle may need to be taken to another dealer If a particular dealership can not assist you then contact the Customer Assistance Center 206 Customer assistance If you have questions or concerns or are unsatisfied with the service you are receiving follow these steps 1 Contact your Sales Representative or Service Advisor at your selling servicing dealership 2 If your inquiry or concern remains unresolved contact the Sales Manager or Service Manager at the dealership 3 If the inquiry or concern cannot be resolved at the dealership level please contact the Ford Customer Assistance Center Ford Motor Company and Ford of Canada dealerships also carry quality parts and accessories providing you with equipment reliability Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service or if you need more help than the dealership could provide after following the steps described above contact the Ford Customer Assistance Center to find an authorized dealership to help you In the United States Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive
153. rage speed Select this function to display your DISTANCE AVG FUEL average speed in miles per hour or TO EMPTY ECONOMY kilometers per hour TRIR TRIP Your vehicle must be moving to calculate your average speed When your vehicle is not moving the average speed is displayed at 0 kilometers 0 miles per hour 23 Controls and features PANEL DIMMER CONTROL Use to adjust the brightness of the A a instrument panel during headlight Saner and parklamp operation DIM e Push up to brighten 4 e Push down to dim HEADLAMP CONTROL O Rotate the headlamp control to the first position to turn on the parking lamps Rotate to the second position to also turn on the headlamps To turn on the interior lamps push the headlamp control in and release To turn the interior lamps off push the headlamp control again Daytime running lamps DRL if equipped Turns the highbeam headlamps on with a reduced output To activate e the key must be in the ON position e the parking brake released and e the headlamp control is in the OFF or Parking lamps position Always remember to turn on your headlamps at dusk or during inclement weather The Daytime Running Light DRL System does not activate your tail lamps and generally may not provide adequate lighting during these conditions Failure to activate your headlamps under these conditions may result in a collision 24 Controls and features High beams ZO Push forwa
154. rake is engaged If brake warning lamp does not illuminate at these times seek service immediately Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately Anti lock brake system ABS Momentarily illuminates when the ignition is turned to the ON position If the light remains on continues to flash or fails to illuminate have the system serviced immediately With the ABS light on the anti lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with the parking brake released Turn signal Iluminates when the left or right turn signal or the hazard lights are turned on If one or both of the a gt indicators stay on continuously or flash faster check for a burned out turn signal bulb Refer to Exterior bulbs in the Maintenance and care chapter High beams Iluminates when the high beam headlamps are turned on D 11 Instrumentation Charging system Illuminates when the ignition is turned to the ON position and the engine is off The light also illuminates when the battery is not charging properly requiring electrical system service Engine oil pressure if equipped Iuminates when the oil pressure falls below the normal range Stop i the vehicle as soon as safely possible and switch off the engine immediately Check the oil level and add oil if needed R
155. rd to activate gt Pull toward you to deactivate Flash to pass Pull toward you to activate and N N release to deactivate N 4 AUTOLAMP CONTROL IF EQUIPPED W The autolamp system provides light OFF sensitive automatic on off control of oes P the exterior lights normally 2 zD controlled by the headlamp control O a The autolamp system also keeps the lights on for a preselected period of AUTO time after the ignition switch is LAMP turned to OFF e To turn autolamps on rotate the control counterclockwise The preselected time lapse is adjustable up to approximately three minutes by continuing to rotate the control counterclockwise e To turn autolamps off rotate the control clockwise to OFF REAR WINDOW DEFROSTER Gy The rear defroster control is located N on the instrument panel CED Controls and features Press the rear defroster control to clear the rear window of thin ice and fog e A small LED will illuminate when the rear defroster is activated The ignition must be in the ON position to operate the rear window defroster The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position To manually turn off the defroster before 10 minutes have passed push the control again CLIMATE CONTROL SYSTEM Manual heating and air conditioning system if equipped a LO OFF VENT FLOOR NORM ria Mix MAX Ww AIC HI Fan speed co
156. ready for I M test condition To ready the on board diagnostics system for I M testing a minimum of 30 minutes of city and highway driving is necessary as described below e First at least 10 minutes of driving on an expressway or highway e Next at least 20 minutes driving in stop and go city type traffic with at least four idle periods Allow the vehicle to sit for at least eight hours without starting the engine Then start the engine and complete the above driving cycle The engine must warm up to its normal operating temperature Once started do not turn off the engine until the above driving cycle is complete BULBS Replacing exterior bulbs Check the operation of the following lamps frequently e Headlamps e Tail lamps e Brakelamps e High mount brakelamp e Turn signals e Backup lamps e License plate lamp Do not remove lamp bulbs unless they will be replaced immediately If a bulb is removed for an extended period of time contaminants may enter the lamp housings and affect performance Replacing headlamp bulbs To remove the headlamp bulb 1 Make sure headlamp switch is in OFF position then open the hood 2 Remove the protective cover by turning the three knobs to the unlock position 188 Maintenance and care 3 Disconnect the electrical connector from the bulb by pulling 4 Remove the bulb retaining ring by rotating it counterclockwise when viewed from the rear to free it from the bulb soc
157. ree times Turn the ignition back to ON 6 Press the unlock control once After a five to ten second delay the door will lock unlock to confirm successful programming 7 Turn the ignition to OFF o BP Cw DY 81 Controls and features Opening the trunk qm Press the control once to open the trunk Ensure that the trunk is closed and latched before driving your vehicle Failure to latch the trunk may cause objects to fall out of the trunk or block the rear view Sounding a panic alarm a Press this control to activate the alarm To deactivate the alarm press the control again or turn the ignition to ACC or ON This device complies with part 15 of the FCC rules and with RS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door s or sound the personal alarm The system automatically turns off after 25 seconds after the UNLOCK button on the remote transmitter is pressed or when the ignition is turned to the START or ACC position The dome lamp control if equipped mu
158. replacement additional TVANSMIULCELS 2 eee ceeeeeee ees 84 replacing the batteries 83 Safety belts see Safety restraints 14 95 96 97 98 99 Safety defects reporting 217 Safety restraints 95 96 97 98 99 belt minder woo eeeeeeeees 101 cleaning the safety belts oo ee 104 198 extension assembly 0 100 for adults ccccadcsessessccnsee 96 97 98 for children c006 109 110 lap Delt sce3sascscedtnsuatesssancesteaecsias 99 warning light and ChiMe venesse 10 14 100 101 Safety seats for children 111 Seat belts see Safety restraints 95 CALS EEA E EAE EAE 91 child safety seats 2 000000000 111 cleanin ern 198 199 SecuriLock passive anti theft system 0 0 84 85 Servicing your vehicle 153 Spark plugs specifications 0 0 0 200 203 Special NOUICE seeswencesveioevtssereacsadcsiee 3 Index Specification chart lubricants enneint 201 203 Speed control cceeceeeeeeeeees 65 Speedometer cccsccsessscesenes 16 Starting your vehicle 117 119 JUMP SUALUING s cccbenbevscctenses 147 Steering speed sensitive ceeee 125 Steering wheel TINE serres nen 64 Tilt steering wheel hersins 64 TPES inas 143 174 175 176 Changing 00 eeeeeeereeeees 143 144 checking the pressure 176 TEPlACINE recne tE 177 TOLAUING sccveriesnr tence 176 snow tires and chains
159. rmal driving position for the best fuel economy Transmission P RN P 21 operates in gears one through four Overdrive can be deactivated by pressing the transmission control switch on the gearshift lever 0 D ON OFF 4 The transmission control indicator light TCIL will illuminate on the 0 D instrument cluster O F F Drive Not shown on the display Activate by pressing the transmission control switch on the gearshift lever with the gearshift in the Drive position The O D OFF indicator will illuminate in the instrument cluster Transmission operates in gears one through three Drive provides more engine braking than Overdrive and is useful when e driving with a heavy load e towing a trailer up or down steep hills e additional engine braking is desired If towing a trailer refer to Driving while you tow in the Trailer Towing chapter To return to Overdrive mode press the transmission control switch The O D OFF indicator light will no longer be illuminated 128 Driving Each time the vehicle is started the transmission will automatically return to normal Overdrive mode Every time the vehicle is shut off and restarted you must press the transmission control switch to cancel overdrive operation if the Overdrive mode is not desired 2 Second Use 2 Second to start up on slippery roads or to provide P RN D 21 additional engine braking on ee ge aa downgrades 1 First
160. rrara EENAA 154 IS TULORY a E S 203 positions of the ignition 64 Infant seats see Safety seats oo cece 111 Inspection maintenance CI M testing seniri 187 Instrument panel CLEANING koien 197 CUSTE eaea 8 198 lighting up panel and interior 0 0 24 location of components 8 Jump starting your vehicle 147 Keyless entry system 0008 86 LOOCK sritan norane n E 80 k yp d serennog 86 programming entry code 87 Keys key in ignition chime 14 positions of the ignition 64 Lamps autolamp system 1 25 bulb replacement specifications chart 192 Cargo AMPS saiscsscessvrecancdesacetoecs 24 daytime running light 24 headlamps cccccccsesssceeseseees 24 headlamps flash to pass 25 instrument panel dimming 24 interior lamps 00 24 192 replacing bulbs 188 190 192 Lane change indicator see Turn signal eeeee 63 Lights warning and indicator 8 aif DaB onssa aias 10 air SUSPENSION scsecesvecseisndesscdevess 12 anti lock brakes ABS 11 122 Drake fs chores a 11 charging system n 12 check engine seirccressscisectssacenceeseses 9 high Deant seesvessesasewenacaesververees 11 JOW Coolant crassiore 10 low Mel essnee i 8 OU PreSSUrE 2ckseiceiectetiesedl cies 12 Overdrive Off verrine 13 safety Delt possesnssecriasirgetiis 10 speed Control ss sssseesse
161. rrupteur de la suspension pneumatique avant de lever to v hicule cric ou pont l vateur ou de le remorquer OFF ARRET This vehicle is equipped with a brake shift interlock feature that prevents the gearshift lever from being moved from P Park when the ignition is in the ON position unless brake pedal is depressed If you cannot move the gearshift lever out of P Park with ignition in the ON position and the brake pedal depressed 1 Apply the parking brake turn ignition key to LOCK then remove the key 2 Insert the key and turn it to OFF Apply the brake pedal and shift to N Neutral 3 Start the vehicle If it is necessary to use the above procedure to move the gearshift lever it is possible that a fuse has blown or the vehicle s brakelamps are not operating properly Refer to Fuses and relays in the Roadside emergencies chapter Do not drive your vehicle until you verify that the brakelamps are working 126 Driving If your vehicle gets stuck in mud or snow it may be rocked out by shifting from forward and reverse gears stopping between shifts in a steady pattern Press lightly on the accelerator in each gear Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat Always set the parking brak
162. rtation 400 Seventh Street Washington D C 20590 You can also obtain other information about motor vehicle safety from the Hotline 217 Index Air bag supplemental restraint system s es 105 and child safety seats 107 CESCHIPUION sschiiiscivessssiceseascveeses 105 CISPOSAl ces esssvcssssaescevseracissiseeteees 109 driver air bag eee 107 indicator light 0 10 109 ODELAGLON virece 107 passenger air bag o on 107 Air cleaner filter 0 0 172 200 Air conditioning eee 26 automatic temperature Control system eceeeeeeeeeees 28 Air SUSPENSION 0 cceeeeeeeeeeeeee 125 description oo eeeeeeeeeeeeeees 125 warning light oeiee 12 Antifreeze see Engine coolant 160 Anti lock brake system see Brakes cc cceseeeees 121 122 Audio system see Radio 35 Automatic transmission driving an automatic overdrive ooo eeeecccceeestceeeseteeees 127 fluid adding uu 167 fluid checking ee 167 fluid refill capacities 200 fluid specification 0 208 Axle lubricant specifications 201 203 refill capacities 0 0 0 200 GractiON lok cernens 129 Battery raer E AO 170 acid treating emergencies 170 charging system warning light isscsceiserscrsnrsis 12 jumping a disabled battery 147 maintenance free s 170 replacement specifications 200 SOPVICING aaen pansa T E TE 170 voltage gauge ecce 19
163. s can be used to select up to four or six preset AM stations and eight or twelve FM stations four to six in FM1 and four to six in FM2 46 Controls and features Setting memory preset siations 1 Select the frequency band with the AM FM select control 2 Select a station Refer to Tune adjust or Seek function for more information on selecting a station 3 Press and hold a memory preset control until the sound returns indicating the station is held in memory on the control you selected VOOWOWR Bass adjust The bass adjust control allows you E j to increase or decrease the audio A system s bass output Treble adjust The treble adjust control allows you to increase or decrease the audio A system s treble output TREB 47 Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers CD select e To begin CD play if CDs are loaded press the CD control The first track of the disc will begin playing After that CD play will begin where it stopped last Press the control again to begin CD changer play if equipped Rewind The rewind control works in CD mode To rewind in CD mode press the CD control preset 1 Press the control again to deactivate rewind mode 48 FADE Controls and features Fast forw
164. sh You can neutralize the acid with a solution of baking soda and water Batteries normally produce explosive gases which can cause personal injury Therefore do not allow flames sparks or lighted substances to come near the battery When working near the battery always shield your face and protect your eyes Always provide proper ventilation 170 Maintenance and care When lifting a plastic cased battery excessive pressure on the end walls could cause acid to flow through the vent caps resulting in personal injury and or damage to the vehicle or battery Lift the battery with a battery carrier or with your hands on opposite corners Keep batteries out of reach of children Batteries contain sulfuric acid Avoid contact with skin eyes or clothing Shield your eyes when working near the battery to protect against possible splashing of acid solution In case of acid contact with skin or eyes flush immediately with water for a minimum of 15 minutes and get prompt medical attention If acid is swallowed call a physician immediately Because your vehicle s engine is electronically controlled by a computer some control conditions are maintained by power from the battery When the battery is disconnected or a new battery is installed the engine must relearn its idle and fuel trim strategy for optimum driveability and performance To begin this process 1 With the vehicle at a complete stop set the parking brake 2 Put the g
165. ss the control a second time within five seconds to unlock all doors Locking the doors amp Press this control to lock all doors The horn will chirp and the parklamps taillamps will flash to confirm the control was pressed Deactivating activating the horn chirp feature The horn chirp feature can be turned on off through the following procedure 79 Controls and features You must complete steps 1 7 within 30 seconds or the procedure will have to be repeated If the procedure needs to be repeated you must wait 30 seconds 1 Turn the ignition key to ON Press the power door unlock control on the door panel three times Turn the ignition key from ON to OFF Press the power door unlock control three times Turn the ignition back to ON The door locks will cycle lock unlock Press the unlock control twice an pr Cw LD 7 After a five to ten second delay the door locks will cycle lock unlock to confirm successful programming 8 Turn the ignition to OFF This feature can be turned on off through the following procedure 1 2 3 4 5 6 7 8 9 0 using the keyless entry keypad 1 Enter the keyless entry keypad factory set code 2 Within 5 seconds press and hold 7 8 control 3 Within 5 seconds with 7 8 held down press and release 1 2 control 4 Release 7 8 control The doors will lock unlock to confirm successful programming Autolock if equipped This feature automatical
166. ssiescadvsiestetncdeeeiieceets 34 Compass electronic 00 73 CalIDTATION 2 cccssnesse ssndeaesscdiees 74 set zone adjustment 0 74 Controls POWEY Seat oe systa 93 94 Coolant checking and adding 160 coolant temperature light 10 refill capacities 0 163 200 specifications 0 201 208 Cruise control see Speed control 0 65 Customer Assistance 0006 136 Ford accessories for your vehicle c ee 213 Ford Extended Service Plan ccccccceeeeseeees 206 Getting assistance outside the U S and Canada 212 Getting roadside assistance 136 Getting the service you need n 206 Ordering additional owner s literature ee 216 The Dispute Settlement Board 209 Utilizing the Mediation Arbitration Program 212 Daytime running lamps see LAMPS cccccccessceeesseeeees 24 Defrost TOAY WINDOW 0c tcs c0scceavencciecscteve 25 Dipstick automatic transmission fluid sesir 167 engine OM oresar 156 Doors lubricant specifications 201 Driving under special conditions through water o e 135 Emergencies roadside Jump starting oo ee 147 Emission control system 186 Engine eeren eaa E E 203 check engine service engine soon light 9 CLEANING ssieivsevesedsrsensarestecnsevnests 196 COANN sesseiocacsraecacessdsnatessredndins 160 fail safe coolant
167. st not be set to the OFF position for the illuminated entry system to operate 82 Controls and features The inside lights will not turn off if e they have been turned on with the dimmer control or e any door is open The battery saver will shut off the interior lamps 30 minutes after the last door is closed or after 10 minutes if the door is left open Replacing the battery The remote transmitter is powered by one coin type three volt lithium battery CR2032 or equivalent Typical operating range will allow you to be up to 10 meters 33 feet away from your vehicle A decrease in operating range can be caused by e weather conditions e nearby radio towers e structures around the vehicle e other vehicles parked next to the vehicle To replace the battery 1 Twist a thin coin between the two halves of the transmitter near the key ring DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART 2 Place the positive side of new battery in the same orientation Refer to the diagram inside the transmitter unit 3 Snap the two halves back together Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle The remote transmitter should operate normally after battery replacement 83 Controls and features Replacing lost transmitters Take all your vehicle s transmitters to your dealer if service is required If you purchase additional transmitters up to four ma
168. start your engine with the air cleaner removed and do not remove it while the engine is running Changing the air filter element 1 Loosen the clamp that secures the air inlet tube to the engine air filter cover and disconnect the tube from the cover 2 Release the clamps that secure the air filter housing cover 3 Carefully separate the two halves of the air filter housing 4 Remove the air filter element from the air filter housing 5 Wipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing 172 Maintenance and care 6 Install a new air filter element Be careful not to crimp the filter element edges between the air filter housing and cover This could cause filter damage and allow unfiltered air to enter the engine if not properly seated 7 Replace the air filter housing cover and secure the clamps 8 Replace the air inlet tube and secure the clamp Failure to use the correct air filter element may result in severe engine damage The customer warranty may be voided for any damage to the engine if the correct air filter element is not used WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades Checking the wiper blades If the wiper blades do not wipe properly clean both the windshield and wipe
169. switch operation refer to the Automatic Transmission Operation section of the Driving chapter SPEED CONTROL IF EQUIPPED To turn speed control on e Press ON Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km h 30 mph 65 Controls and features Do not use the speed control in heavy traffic or on roads that are winding slippery or unpaved Do not shift the gearshift lever into N Neutral with the speed control on To turn speed control off e Press OFF or e Turn off the vehicle ignition Once speed control is switched off the previously programmed set speed will be erased To set a speed e Press SET SET ACC SET ACCEL For speed control to operate the speed control must be ON and the vehicle speed must be greater than 48 km h 80 mph If you drive up or down a steep hill your vehicle speed may vary momentarily slower or faster than the set speed This is normal Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill If your vehicle speed is faster than the set speed while driving on a downhill you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed 66 Controls and features If your vehicle slows down more than 16 km h 10 mph below your set speed on an uphill your speed control will disengage This is normal Pressing RES RSM RESUME will re engage it Do not use the speed contr
170. t install and use the safety seat properly the child may be injured in a sudden stop or collision When installing a child safety seat e Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter e Use the correct safety belt buckle for that seating position the buckle closest to the direction the tongue is coming from Insert the belt tongue into the proper buckle until you hear a snap and feel it latch Make sure the tongue is securely fastened in the buckle 111 Seating and safety restraints e Keep the buckle release button pointing up and away from the safety seat with the tongue between the child seat and the release button to prevent accidental unbuckling Place seat back in upright position e Put the safety belt in the automatic locking mode Refer to Automatic locking mode passenger side front and outboard rear seating positions if equipped Ford recommends the use of a child safety seat having a top tether strap Install the child safety seat in a seating position which is capable of providing a tether anchorage For more information on top tether straps refer to Attaching safety seats with tether straps Carefully follow all of the manufacturer s instructions included with the safety seat you put in your vehicle If you do not install and use the safety seat properly the child may be injured in a sudden stop or collision Installing chi
171. tach the battery cables Ensure that vent caps are tight and level 5 Turn the heater fan on in both vehicles to protect any electrical surges Turn all other accessories off Connecting the jumper cables 1 Connect the positive booster cable to the positive terminal of the discharged battery Note In the illustrations lightning bolts are used to designate the assisting boosting battery 2 Connect the other end of the positive cable to the positive terminal of the assisting battery 148 Roadside emergencies 3 Connect the negative cable to the negative terminal of the assisting battery 4 Make the final connection of the negative cable to an exposed metal part of the stalled vehicle s engine away from the battery and the carburetor fuel injection system Do not use fuel lines engine rocker covers or the intake manifold as grounding points Do not connect the end of the second cable to the negative terminal of the battery to be jumped A spark may cause an explosion of the gases that surround the battery 5 Ensure that the cables are clear of fan blades belts moving parts of both engines or any fuel delivery system parts 149 Roadside emergencies Jump starting 1 Start the engine of the booster vehicle and run the engine at moderately increased speed 2 Start the engine of the disabled vehicle 3 Once the disabled vehicle has been started
172. talled only by a qualified technician See your local dealer for driveshaft removal installation Improper removal installation of the driveshaft can cause transmission fluid loss damage to the driveshaft and internal transmission components 134 Driving DRIVING THROUGH WATER Do not drive quickly through standing water especially if the depth is unknown Traction or brake capability may be limited and if the ignition system gets wet your engine may stall Water may also enter your engine s air intake and severely damage your engine If driving through deep or standing water is unavoidable proceed very slowly Never drive through water that is higher than the bottom of the hubs for trucks or the bottom of the wheel rims for cars Once through the water always try the brakes Wet brakes do not stop the vehicle as effectively as dry brakes Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage 135 Roadside emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern Ford offers a complimentary roadside assistance program This program is separate from the New Vehicle Limited Warranty The service is available e 24 hours seven days a week e for the Basic warranty period Canada or
173. tance should these limitations be exceeded Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and or personal injury The weight of your loaded trailer should not exceed 907 kg 2 000 Ibs The GCW of your vehicle and trailer should not exceed 2 993 kg 6 600 Ibs TRAILER TOWING Your vehicle is classified as a light duty towing vehicle Do not tow a trailer until your vehicle has been driven at least 3 200 km 2 000 miles Towing a trailer places an additional load on your vehicle s engine transmission brakes tires and suspension Inspect these components carefully after towing Your loaded trailer should weigh no more than 907 kg 2 000 Ibs Do not exceed the GVWR or the GAWR specified on the certification label Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage transmission axle damage structural damage loss of control and personal injury 131 Driving Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle See your dealer or a reliable trailer dealer if you require assistance Hitches Do not use hitches that clamp onto the vehicle bumper Use a load carrying hitch You must distribute the load in your trailer so that 10 of the total weight of the trailer is on the tongue Safety chains Always connect the trailer s safety chains to the frame or hook r
174. tes when the ignition is first turned to the ON position to check the bulb If it comes on after the engine is started one of the engine s emission control systems may be malfunctioning The light may illuminate without a driveability concern being noted The vehicle will usually be drivable and will not require towing What you should do if the check engine light illuminates Light turns on solid This means that the OBD II system has detected a malfunction Temporary malfunctions may cause your Check Engine light to illuminate Examples are 1 The vehicle has run out of fuel The engine may misfire or run poorly 2 Poor fuel quality or water in the fuel 3 The fuel cap may not have been properly installed and securely tightened These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and or properly installing and securely tightening the gas cap After three driving cycles without these or any other temporary malfunctions present the Check Engine light should turn off A driving cycle consists of a cold engine startup followed by mixed city highway driving No additional vehicle service is required If the Check Engine light remains on have your vehicle serviced at the first available opportunity Instrumentation Light is blinking Engine misfire is occurring which could damage your catalytic converter You should drive in a moderate fashion avoid heavy
175. the SEL control to select ON or OFF With the feature on use A the SEEK or SCAN control to SEL find a radio station broadcasting a traffic report if it is broadcasting y RDS data Traffic information is not available in most U S markets Program type e Press the RDS control until the FIND program type is displayed RDS mN C 57 Controls and features Use the SEL control to select the program type With the feature A on use the SEEK or SCAN SEL control to find the desired program type from the following y selections e Classic e Country e Info e Jazz e Oldies e R amp B e Religious e Rock e Soft e Top 40 Show e With RDS activated press the RDS control until SHOW is RDS displayed e Use the SEL control to select TYPE the display shows the A program type NAME the SEL display shows the call letters of the station or NONE y RDS clock feature Refer to Setting the clock for information Setting the clock Your vehicle is equipped with a separate instrument panel mounted clock Please refer to Clock in this chapter for instructions on setting the clock 58 Controls and features CD changer if equipped The CD changer is located in one of the following locations e in the trunk e in the center console e under the driver s seat 1 Slide the door to access the CD changer magazine 2 Press amp to eject the magazine 3 Turn the magazine A over
176. the skin and or clothing promptly remove contaminated clothing and wash skin thoroughly with soap and water Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation Be particularly careful if you are taking Antabuse or other forms of disulfiram for the treatment of alcoholism Breathing gasoline vapors or skin contact could cause an adverse reaction In sensitive individuals serious personal injury or sickness may result If fuel is splashed on the skin promptly wash skin thoroughly with soap and water Consult a physician immediately if you experience an adverse reaction When refueling always shut the engine off and never allow sparks or open flames near the filler neck Never smoke while refueling Fuel vapor is extremely hazardous under certain conditions Care should be taken to avoid inhaling excess fumes The flow of fuel through a fuel pump nozzle can produce static electricity which can cause a fire if fuel is pumped into an ungrounded fuel container Use the following guidelines to avoid static build up when filling an ungrounded fuel container Place approved fuel container on the ground DO NOT fill a fuel container while it is in the vehicle Keep the fuel pump nozzle in contact with the fuel container while filling DO NOT use a device that would hold the fuel pump handle in the fill position Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1 8 turn on o
177. tic transmission gearshift lever and allows key removal Cy 3 OFF shuts off the engine and all accessories without locking the steering wheel 4 ON all electrical circuits operational Warning lights illuminated Key position when driving 5 START cranks the engine Release the key as soon as the engine starts TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down Hold the control while adjusting the wheel to the desired position then release the control A Never adjust the steering wheel when the vehicle is moving 64 Controls and features OVERDRIVE CONTROL Activating overdrive Overdrive is the normal drive position for the best fuel economy The overdrive function allows automatic upshifts and downshifts through all available gears Deactivating overdrive Press the Transmission Control Switch TCS located on the end of the gearshift lever The Transmission Control Indicator Light TCIL will illuminate on the instrument cluster 0 D ON OFF 0 D When you shut off and re start your vehicle the transmission will automatically return to normal Overdrive mode 4 The transmission will operate in all gears except overdrive To return to normal overdrive mode press the Transmission Control Switch again The TCIL will no longer be illuminated For additional information about the gearshift lever and the transmission control
178. time only use this mode to prevent undesirable odors from entering the vehicle FLR Allows for maximum heating by distributing outside air through the floor ducts However the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode MIX Distributes outside air through the windshield defroster ducts and the floor ducts Heating and air conditioning capabilities are provided in this mode For added customer comfort when the temperature control knob is anywhere in between the full hot and full cold positions the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts If the temperature is about 10 C 50 F or higher the air conditioner will automatically dehumidify the air to reduce fogging DEF Distributes outside air through the windshield defroster ducts It can be used to clear ice or fog from the windshield If the temperature is about 10 C 50 F or higher the air conditioner will automatically dehumidify the air to reduce fogging Operating tips In humid weather select 7 before driving This will reduce fogging on your windshield After a few minutes select any desired position 27 Controls and features e To prevent humidity buildup inside the vehicle do not drive with the climate control system in the OFF or MAX A C position e Do not put objects under the front seat that will interfere with the
179. tion overload Weak signals are sometimes captured by stronger signals when you pass a broadcast tower A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo Audio system warranties and service Refer to the Warranty Guide for audio system warranty information If service is necessary see your dealer or a qualified technician TURN SIGNAL CONTROL 5 e Push down to activate the left turn signal e Push up to activate the right turn signal The flash rate of the turn signal will speed up considerably if the Lighting Control Module detects a left or right turn lamp bulb front or rear is burned out WINDSHIELD WIPER WASHER CONTROLS SJ Rotate the windshield wiper control Ix to the desired interval low or high speed position The bars of varying length are for intermittent wipers When in this position rotate the control upward for fast intervals and downward for slow intervals Push the control on the end of the stalk to activate washer Push and hold for a longer wash cycle 63 Controls and features POSITIONS OF THE IGNITION 1 ACCESSORY allows the electrical accessories such as the radio to 3 4 operate while the engine is not 4 running AB 2 LOCK locks the steering wheel 2 automa
180. to the empty reserve still present in the tank 183 Maintenance and care For consistent results when filling the fuel tank e Use the same filling rate setting dow medium high each time the tank is filled e Allow three automatic click offs when filling e Always use fuel with the recommended octane rating e Use a known quality gasoline preferably a national brand e Use the same side of the same pump and have the vehicle facing the same direction each time you fill up e Have the vehicle loading and distribution the same every time Your results will be most accurate if your filling method is consistent Calculating fuel economy 1 Fill the fuel tank completely and record the initial odometer reading in kilometers or miles 2 Each time you fill the tank record the amount of fuel added in liters or gallons 3 After at least three to five tank fill ups fill the fuel tank and record the current odometer reading 4 Subtract your initial odometer reading from the current odometer reading 5 Follow one of the simple calculations in order to determine fuel economy Multiply liters used by 100 then divide by total kilometers traveled Divide total miles traveled by total gallons used Keep a record for at least one month and record the type of driving city or highway This will provide an accurate estimate of the vehicle s fuel economy under current driving conditions Additionally keeping records duri
181. ty belt system periodically to make sure there are no nicks wear or cuts If your vehicle has been involved in an accident refer to the Safety belt maintenance section in the Seating and safety restraints chapter 198 Maintenance and care Cleaning leather seats if equipped To clean simply use a soft cloth dampened with water and a mild soap Wipe the leather again with a damp cloth to remove soap residue Dry with a soft cloth For tougher soiling concerns Ford recommends using the Deluxe Leather Care Kit F8AZ 19G253 AA which is available from your Ford Dealer This mild cleaner and special pad cleans the leather and maintains its natural beauty Follow the instructions on the cleaner label Regular cleaning of your leather upholstery helps maintain its resiliency and color Do not use household cleaning products alcohol solutions solvents or cleaners intended for rubber vinyl or plastics Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner Remove fresh spots immediately Do not use household or glass cleaners These agents can stain and discolor the fabric Use a mild soap and water solution if necessary 199 Capacities and specifications MOTORCRAFT PART NUMBERS Refer to Vehicle Emissions Control Information VECI decal for spark plug gap information REFILL CAPACITIES Ford Part Name Engine oil includes Motorcraft SAE 5W 30 filter change Super Premium Motor 4
182. u they can direct you to the nearest Ford affiliate office If you buy your vehicle in North America and then relocate outside of the U S or Canada register your vehicle identification number VIN and new address with Ford Motor Company Worldwide Direct Market Operations FORD CAR CARE PRODUCTS FOR YOUR VEHICLE Ford has many quality products available from your dealer to clean your vehicle and protect its finishes These quality products have been specifically engineered to fulfill your automotive needs they are custom designed to complement the style and appearance of your vehicle Each product is made from high quality materials and that meet or exceed Ford s rigid specifications For best results use the following or products of equivalent quality Ford Custom Clearcoat Polish Ford Custom Silicone Gloss Polish Ford Custom Vinyl Protectant not available in Canada Motorcraft Vinyl Conditioner Canada only 213 Customer assistance Ford Deluxe Leather and Vinyl Cleaner not available in Canada Motorcraft Vinyl Cleaner Canada only Ford Extra Strength Tar and Road Oil Remover not available in Canada Ford Extra Strength Upholstery Cleaner Canada only Ford Extra Strength Upholstery Cleaner not available in Canada Ford Metal Surface Cleaner Ford Multi Purpose Cleaner Motorcraft Car Wash Concentrate Motorcraft Carlite Glass Cleaner Ford Spot and Stain Remover Ford Super Premium Tire and Trim Dressing
183. und cover The emission system heats up the engine compartment and exhaust system which can start a fire Do not start your vehicle in a closed garage or in other enclosed areas Exhaust fumes can be toxic Always open the garage door before you start the engine See Guarding against exhaust fumes in this chapter for more instructions If you smell exhaust fumes inside your vehicle have your dealer inspect your vehicle immediately Do not drive if you smell exhaust fumes Important safety precautions A computer system controls the engine s idle revolutions per minute RPM When the engine starts the idle RPM runs faster to warm the engine If the engine idle speed does not slow down automatically have the vehicle checked Do not allow the vehicle to idle for more than 10 minutes at the higher engine RPM Before starting the vehicle 1 Make sure all vehicle occupants have buckled their safety belts For more information on safety belts and their proper usage refer to the Seating and safety restraints chapter 2 Make sure the headlamps and vehicle accessories are off 117 Starting 3 Make sure the parking brake is set HOOD 4 Make sure the gearshift is in P Park j P RNO 21 E 5 Turn the key to 4 ON without p s turning the key to 5 START 7 4 If there is difficulty in turning the 3 key firmly rotate the steering wheel N 5 left and right until the key turns freely This conditio
184. ur Scheduled Maintenance Guide for Severe Duty requirements Traction Lok axles use 1 6 1 8L 3 50 3 75 pints of rear axle lubricant Add 118 ml 4 oz of Additive Friction Modifier C8AZ 19B546 A or equivalent meeting Ford specification EST M2C118 A for complete refill of Traction Lok rear axle Service refill capacities are determined by filling the rear axle 6 mm to 14 mm 1 4 inch to 9 16 inch below the bottom of the filler hole LUBRICANT SPECIFICATIONS Item Ford part Ford part Ford name number specification Brake fluid High C6AZ 19542 AB ESA M6C25 A Performance DOT 3 Motor Vehicle Brake Fluid Door Silicone F7AZ 19G208 BA ESR M13P4 A weatherstrips Lubricant and F5AZ 19553 AA Engine coolant Ford Premium E2FZ 19549 AA ESE M97B44 A Engine Coolant in Canada Motorcraft CXC 8 B 201 Capacities and specifications Item Ford part Ford part Ford name number specification Engine oil Motorcraft SAE XO 5W30 QSP WSS M2C153 G 5W 30 Super with API Premium Motor Certification Oil Mark Hinges latches Multi Purpose DOAZ 19584 AA ESB M1C93 B or striker plates Grease or ESR M1C159 A fuel filler door F5AZ 19G209 AA hinge and seat tracks Lock cylinders Penetrating and K8AZ 19A501 B none Lock Lubricant Power steering Motorcraft XT 2 QDX MERCON fluid MERCON ATF Automatic Motorcraft XT 5 QM transmission MERCON V MERCON V 4R70W ATF Rear Axle Motorcraft SAE XY 80W90 QL WSP M
185. ur vehicle in an emergency Since the parking brake applies only the rear brakes the vehicle s stopping distance will increase greatly and the handling of your vehicle will be adversely affected Your vehicle has an automatic parking brake release except for police fleet vehicles which have the manual release To release the parking brake 1 Turn the ignition to the ON position 2 Press the brake pedal 3 Move the gearshift from the P Park position to one of the forward gears the parking brake will not release automatically when you shift into reverse The brake pedal must remain pressed while the gearshift is moved If the parking brake fails to release after completing this procedure use the manual parking brake release lever Pull the lever to manually release the parking brake TRACTION CONTROL IF EQUIPPED Your vehicle may be equipped with the optional Traction Control system This system helps you maintain the stability and steerability of your vehicle It is especially useful on slippery and or hilly road surfaces 123 Driving The system operates by detecting and controlling wheel spin The system borrows many of the electronic and mechanical elements already present in the anti lock braking system ABS Wheel speed sensors allow excess rear wheel spin to be detected by the Traction Control portion of the ABS computer Any excessive wheel spin is controlled by automatically applying and releasin
186. ure The Belt Minder feature can be deactivated activated by performing the following procedure Before following the procedure make sure that e the parking brake is set e the gearshift is in P Park automatic transmission e the ignition switch is in the OFF position e all vehicle doors are closed the driver s safety belt is unbuckled e the parklamps headlamps are in OFF position If vehicle is equipped with Autolamps this will not affect the procedure To reduce the risk of injury do not deactivate activate the Belt Minder feature while driving the vehicle 1 Turn the ignition switch to the RUN or ON position DO NOT START THE ENGINE 2 Wait until the safety belt warning light turns off Approximately 1 2 minutes e Steps 3 5 must be completed within 60 seconds or the procedure will have to be repeated 3 Buckle then unbuckle the safety belt three times ending with the safety belt unbuckled This can be done before or during Belt Minder warning activation 4 Turn on the parklamps headlamps turn off the parklamps headlamps 5 Buckle then unbuckle the safety belt three times ending with the safety belt unbuckled e After step 5 the safety belt warning light will be turned on for three seconds 103 Seating and safety restraints 6 Within seven seconds of the safety belt warning light turning off buckle then unbuckle the safety belt e This will disable Belt Minder if it is currently enabled
187. vadees 138 139 Garage door Opener cccee 69 Gas cap see Fuel cap 180 Gas mileage see Fuel economy sessies 183 GAUB ES sisinya eais 15 battery voltage gauge 19 engine coolant temperature Sauge eee 18 engine oil pressure gauge 19 fuel BAUS ciscss cccacsseansesvecesesceeven 15 OGOMEULET sssrinin 17 speedometer cccccccccesseeeees 16 trip OGOMETEL cceescceeeneees 18 GAWR Gross Axle Weight Rating 129 GOTMILION sirier 129 driving with a heavy load 129 LOCATION as ccsecisecssassccsssssaiensssseees 129 GVWR Gross Vehicle Weight Rating 129 calculating senceres 129 CGETMIGION ssssecssssdscsdsseaccexteccasess 129 driving with a heavy load 129 locatio sss ceiseiessiiscetiovnectenaeeees 129 Hazard flashers 0 s cs cccsceseevccsoes 137 Head restraints ccccceeeee 91 Headlamps sirenen 24 AMTMNG een ninae Ae 193 autolamp system cccccceeees 25 bulb specifications 00 192 daytime running lights 24 flash tO pass wo eeeccecceesseeeeeeeees 25 high beam persere 11 25 replacing bulbs 0 0 188 turning on and off 0 24 warning chime ceeeeeeee 15 Heatihg secvsias wesitecaaesaxeeaveondey ts eaves 26 220 heating and air conditioning SV SUCIUL 2uccpceacdeedeecasenngtaetetsecarasss 26 HomeLink universal transceiver see Garage door opener nsss 69 70 71 72 Hood se
188. window sticker These numbers represent the Range of L 100 km MPG expected on the vehicle under optimum conditions Your fuel economy may vary depending upon the method of operation and conditions EMISSION CONTROL SYSTEM tC Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards To make sure that the catalytic converter and other emission control components continue to work properly e Use only the specified fuel listed e Avoid running out of fuel e Do not turn off the ignition while your vehicle is moving especially at high speeds Have the items listed in your Scheduled Maintenance Guide performed according to the specified schedule 186 Maintenance and care The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to the life and performance of your vehicle and to its emissions system If other than Ford Motorcraft or Ford authorized parts are used for maintenance replacements or for service of components affecting emission control such non Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire Illumination of the Check Engine light charging
189. wiper still does not wipe properly this could be caused by substances on the windshield or rear window such as tree sap and some hot wax treatments used by commercial car washes Clean the outside of the windshield or rear window with a non abrasive cleaner such as Ford Ultra Clear Spray Glass Cleaner E4AZ 19C507 AA available from your Ford Dealer Do not use abrasive cleansers on glass as they may cause scratches The windshield or rear window is clean if beads do not form when you rinse it with water The windshield rear window and wiper blades should be cleaned on a regular basis and blades or rubber elements replaced when worn Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal When washing e Take care when using a power washer to clean the engine The high pressure fluid could penetrate the sealed parts and cause damage e Do not spray with cold water to avoid cracking the engine block or other engine components e Never apply anything to the drive belt including belt dressing 196 Maintenance and care N NJA TD T N is rezi e Cover the highlighted areas to prevent water damage when cleaning the engine e Never wash or rinse the engine while it is running water in the running engine may cause internal damage Cleaning the instrument panel Clean with a damp cloth
190. xceeding these limits may allow water to enter critical vehicle components adversely affecting driveability emissions reliability and causing internal transmission damage 133 Driving Replace the rear axle lubricant anytime the axle has been submerged in water Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair required Disconnect the wiring to the trailer before backing the trailer into the water Reconnect the wiring to the trailer after the trailer is removed from the water Recreational towing all wheels on the ground Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground such as behind a recreational vehicle These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication All Rear Wheel Drive RWD vehicles This applies to all cars and 4x2 trucks sport utilities with rear wheel drive capability An example of recreational towing is towing your vehicle behind a Motorhome The following recreational towing guidelines are designed to ensure that your transmission is not damaged e Place the transmission in N Neutral e Maximum speed is 56 km h 35 mph e Maximum distance is 80 km 50 miles If a distance of 80 km 50 miles or a speed of 56 km h 85 mph must be exceeded you must disconnect the driveshaft Ford recommends the driveshaft be removed ins
191. xtreme cold Allow tapes that may have been exposed to extreme temperatures to reach a moderate temperature before playing e Tighten very loose tapes by inserting a finger or pencil into the hole and turning the hub e Remove loose labels before inserting tapes e Do not leave tapes in the cassette player for a long time when not being played Radio frequency information The Federal Communications Commission FCC and the Canadian Radio and Telecommunications Commission CRTC establish the frequencies AM and FM stations may use for their broadcasts Allowable frequencies are AM 530 540 1600 1610 kHz FM 87 7 87 9 107 7 107 9 MHz Not all frequencies are used in a given area Radio reception factors Three factors can affect radio reception e Distance strength The further an FM signal travels the weaker it is The listenable range of the average FM station is approximately 40 km 24 miles This range can be affected by signal modulation Signal modulation is a process radio stations use to increase their strength volume relative to other stations e Terrain Hills mountains and tall buildings between your vehicle s antenna and the radio station signal can cause FM reception problems Static can be caused on AM stations by power lines electric fences traffic lights and thunderstorms Moving away from an interfering structure out of its shadow returns your reception to normal 62 Controls and features e Sta
192. y i e if the transmission slips or shifts slowly or if you notice some sign of fluid leakage 167 Maintenance and care Automatic transmission fluid expands when warmed To obtain an accurate fluid check drive the vehicle until it is at normal operating temperature approximately 30 km 20 miles If your vehicle has been operated for an extended period at high speeds in city traffic during hot weather or pulling a trailer the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking 1 Drive the vehicle 30 km 20 miles or until it reaches normal operating temperature 2 Park the vehicle on a level surface and engage the parking brake 3 With the parking brake engaged and your foot on the brake pedal start the engine and move the gearshift lever through all of the gear ranges Allow sufficient time for each gear to engage 4 Latch the gearshift lever in P Park and leave the engine running 5 Remove the dipstick wiping it clean with a clean dry lint free rag If necessary refer to Identifying components in the engine compartment in this chapter for the location of the dipstick 6 Install the dipstick making sure it is fully seated in the filler tube 7 Remove the dipstick and inspect the fluid level The fluid should be in the designated area for normal operating temperature or ambient temperature Low fluid level Do not drive the vehicle if the fluid 4 level is at the bottom of the
193. y be programmed into memory perform the following procedure To reprogram the transmitters yourself place the key in the ignition and turn from OFF to ON four times in rapid succession within 3 seconds After doors lock unlock press any control on all transmitters up to four When completed turn the ignition to OFF All transmitters must be programmed at the same time SECURILOCK PASSIVE ANTI THEFT SYSTEM Your vehicle is equipped with a coded key anti theft system Only the correct key will be able to start your vehicle If your keys are lost or stolen you must take your vehicle to your dealership for key reprogramming This system provides an advanced level of vehicle theft protection Your vehicle s engine can only be started with the two coded keys provided with your vehicle Each time you start your vehicle the coded key is read by the anti theft system If the key identification code matches the code stored in the anti theft system the vehicle s engine is allowed to start If the key identification code does not match the code stored in the system or if a coded key is not detected vehicle theft situation the vehicle s engine will not operate If there is any anti theft problem with your vehicle ensure ALL coded keys for that vehicle are brought to the dealership to aid in troubleshooting The SecuriLock passive anti theft system is not compatible with aftermarket remote start systems Use of these syste
194. you when fully extended Do not use extensions to change the fit of the shoulder belt across the torso Safety belt warning light and indicator chime A The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts 100 Seating and safety restraints Conditions of operation The driver s safety belt is not buckled before the ignition switch is turned to the ON position The driver s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding The driver s safety belt is buckled before the ignition switch is turned to the ON position Belt minder if equipped The safety belt warning light illuminates1 2 minutes and the warning chime sounds 4 8 seconds The safety belt warning light and warning chime turn off The safety belt warning light and indicator chime remain off The Belt Minder feature is a supplemental warning to the safety belt warning function This feature provides additional reminders to the driver that the driver s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster The driver s safety belt is not buckled approximately 5 seconds after the safety belt warning light has turned off The driver s safety belt is buckled while the safety belt indicator light is illuminated and the safety b
195. your tires wear evenly and last longer rotate them as indicated in the Scheduled Maintenance Guide If you notice that the tires wear unevenly have them checked e Four tire rotation for vehicles with aluminum wheels NZ AN K A tA I l 176 Maintenance and care 4 e Five tire rotation for vehicles with steel wheels and full size spare tires bee vA Replacing the tires Replace the tires when the wear band is visible through the tire treads JOS When replacing full size tires never mix radial bias belted or bias type tires Use only the tire sizes that are listed on the Certification Label Make sure that all tires are the same size speed rating and load carrying capacity Use only the tire combinations recommended on the label If you do not follow these precautions your vehicle may not drive properly and safely Make sure that all replacement tires are of the same size type load carrying capacity and tread design e g All Terrain etc as originally offered by Ford 177 Maintenance and care Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over Tires that are larger or smaller than your vehicle s original tires may also affect the accuracy of your speedometer SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have o

Ford 1999 F-350 Automobile User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents