Home

Ford 1998 Ranger Automobile User Manual

1. I aE H CHECK ENGINE c lt FUEL DOOR FUEL g RESET B F ao Check engine Your vehicle is equipped with a computer that monitors the engine s CHECK emission control system This system is commonly known as the ENGINE On Board Diagnostics System OBD II This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards The OBD II system also assists the service technician in properly servicing your vehicle Instrumentation The Check Engine indicator light illuminates when the ignition is first turned to the ON position to check the bulb If it comes on after the engine is started one of the engine s emission control systems may be malfunctioning The light may illuminate without a driveability concern being noted The vehicle will usually be drivable and will not require towing What you should do if the check engine light illuminates Light turns on solid This means that the OBD II system has detected a malfunction Temporary malfunctions may cause your Check Engine light to illuminate Examples are 1 The vehicle has run out of fuel The engine may misfire or run poorly 2 Poor fuel quality or water in the fuel 3 The fuel cap may not have been properly installed and securely tightened These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and or proper
2. Windshield washer fluid reservoir Engine oil filler cap Transmission fluid dipstick automatic transmission Engine oil dipstick Power steering fluid reservoir Brake fluid reservoir Clutch fluid reservoir manual transmission o I a n bP WH FR Battery 9 Air filter assembly 10 Engine coolant reservoir 114 Maintenance and care ENGINE OIL Checking the engine oil Check the engine oil each time you fuel your vehicle 1 Make sure the vehicle is on level ground 2 Turn the engine off and wait a few minutes for the oil to drain into the oil pan 3 Set the parking brake and ensure the gearshift is securely latched in P Park automatic transmissions or 1 First manual transmissions 4 Open the hood Protect yourself from engine heat 5 Locate and carefully remove the engine oil level indicator dipstick e 2 5L I4 engine 115 Maintenance and care e 3 0L V6 4 0L V6 engine ADD 1 aT gt REET lt FULL 6 Wipe the indicator clean Insert the indicator fully then remove it again e If the oil level is between the MIN and MAX marks 2 5L engine or between the ADD and FULL marks 3 0L and 4 0L engine the oil level is acceptable DO NOT ADD OIL If the oil level is below the MIN mark 2 5L engine or ADD mark 3 0L and 4 0L engine add enough oil to raise the level within the MIN MAX range 2 5L engine or the A
3. Once the doors are closed the system will arm in 30 seconds When you press the lock control twice within 5 seconds the horn will chirp once to let you know that the system is armed If the doors are not closed and you press the remote entry transmitter twice to confirm the doors are locked the horn will chirp twice to warn you that the system is not arming 35 Controls and features Disarming the system You can disarm the system by any of the following actions e Unlock the doors by using your remote entry transmitter e Unlock the doors with a key Turn the key full travel toward the front of the vehicle to make sure the alarm disarms e Turn ignition to ACC or ON e Press the panic control on the remote entry transmitter This will disarm the system only if the alarm is sounding 36 Seating and safety restraints SEATING Front seats A Never adjust the driver s seat or seatback when the vehicle is moving A Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop A Always drive and ride with your seatback upright and the lap belt snug and low across the hips Lift handle to move seat forward or backward 37 Seating and safety restraints Pull lever up to adjust seatback Using the manual lumbar support Turn the lumbar support control clockwise to increase firmness A Turn the lumbar support control counterclockwise to increa
4. The driver s safety belt is buckled The safety belt warning light and before the ignition switch is turned indicator chime remain off to the ON position Safety belt maintenance Check the safety belt systems periodically to make sure they work properly and are not damaged Check the safety belts to make sure there are no nicks wears or cuts All safety belt assemblies including retractors buckles front seat belt buckle assemblies slide bar if equipped shoulder belt height adjusters if equipped child safety seat tether bracket assemblies Gif equipped and attaching hardware should be inspected after a collision Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced However if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly they do not need to be replaced Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted Failure to replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision Refer to Cleaning and maintaining the safety belts in the Maintenance and care section 46 Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM SRS Important supplemental restraint system
5. s s go n io ee g g 3 D SE zi 2 o O E T 2 z z g i ES z S 2o a 8 4 2 S 68 a gt lt E gs O SE O Bo a ry SE o ke ES oO 55 So 35 2o ait on S 38g F EG a5 B ao 2 system or translation in whole or part is not permitted without written authorization from Ford Motor Company Copyright 1997 Ford Motor Company ji Introduction ICONS Indicates a warning Read the following section on Warnings for a full explanation Indicates vehicle information related to recycling and other environmental concerns will follow Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others your vehicle and its equipment BREAKING IN YOUR VEHICLE There are no particular breaking in rules for your vehicle During the first 1 600 km 1 000 miles of driving vary speeds frequently This is necessary to give the moving parts a chance to break in If possible you should avoid full use of the brakes for the first 1 600 km 1 000 miles INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing Ford may change the contents without notice and without incurring obligation SPECIAL NOTICES Notice
6. 64 Driving RABS warning lamp The warning lamp in the instrument cluster illuminates if a RABS fault is detected Have your vehicle serviced as soon as possible Normal braking is still effective unless the BRAKE warning lamp is O also illuminated BRAKE Using RABS e In an emergency applying full pressure may cause the front wheels to lock If the front brakes lock the vehicle cannot be steered You should apply the brakes with steadily increasing force as if squeezing the brakes If you feel the front wheels begin to lock momentarily release the pedal and repeat the squeeze technique e We recommend that you familiarize yourself with how the RABS performs However avoid unnecessary risks Four wheel anti lock brake system ABS if equipped On vehicles equipped with an anti lock braking system ABS a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events Pedal pulsation coupled with noise while braking under panic conditions or on loose gravel bumps wet or snowy roads is normal and indicates proper functioning of the vehicle s anti lock brake system If the vehicle has continuous vibration or shudder while braking felt mainly in the steering wheel the vehicle most likely needs service The ABS operates by detecting the onset of wheel lock up during brake applications and compensating for this tendency The wheels are prevented from locking eve
7. Driving with a 5 speed automatic transmission 4 0L engines only Understanding gearshift positions Hold the brake pedal down while you move the gearshift lever from position to position If you do not hold the brake pedal down your vehicle may move unexpectedly and injure someone Pull the gearshift lever towards you and downward to move the automatic gearshift P Park Always come to a complete stop before shifting into or out of P PRN D 21 Park Make sure the gearshift is Eo eaa a securely latched in P Park R Reverse With the gearshift in R Reverse the vehicle will move backward P R N D 2 1 Pe before shifting into and out of R Reverse 70 Driving N Neutral With the gearshift in N Neutral the vehicle can be started and is P RN D 21 free to roll Hold the brake pedal eee See down while in this gear Overdrive The normal driving position for the best fuel economy Transmission P RN P 21 operates in gears one through five 0 D The transmission control indicator g D Overdrive can be deactivated by pressing the transmission control switch on the end of the gearshift lever light TCIL will illuminate on the instrument cluster OF F Drive Not shown on the display Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the position The TCIL will illuminate on the instrument clu
8. Vehicle Regular Cab dimensions Short Wheel Long Wheel Base SWB Base LWB mm in mm in 3 Overall height 1 575 62 0 1 586 62 4 1 585 62 4 152 nd specifications cities a Capacities and specifications IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located The Safety Compliance Certification Label is located on the front door latch pillar on the driver s side Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel Engine number MFD BY FORD MOTOR CO IN U S A DATE XXXXX FGAWR XXXXXX XXXXXXX GVWR XXXXX LB XXXXX KG RGAWR XXXXXXX XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE VIN XXXXXXXXXXXXXXXXX TYPE XXXXXXXXXXXXXXX MAXIMUM LOAD OCCUPANTS LUGGAGE XXXKG XXXXLB OCCUPANTS X TOTAL X FR X 2N TIRE XXXX XXXXX XXX PRESSURE FR XXX kPa 33 PSI PRESSURE RR XXX kPa 33 PSI TRAILER TOWING SEE OWNER GUIDE EXT PNT XXXXXX XXXXXX_ RC XX D X RR OCCUPANTS LUGGAGE XX XXXKG XXXXLB X XXXKG XXXXLB COLD COLD DSO XXXX_ F
9. 138 INS IN G8 idk see E 151 service points 112 113 114 Engine block heater aese 62 Engine coolant checking and adding 121 disposal ciicticlnsteocssteg heaves 122 refill capacities ce 123 Engine oil oc eeeeceeeees 115 117 changing oil and oil filter 118 checking and adding 115 117 Exhaust fumes ccccceeeeeeees 63 Foglamps ccecceeesseeeseeeeseeeeees 16 Four Wheel Drive vehicles 74 control trac eee 22 75 indicator light ee 75 Fuel calculating fuel economy 137 improving fuel economy 92 OCTANE tating dees peace 136 quality srie eert 136 running out of fuel 137 safety information relating to automotive fuels 135 Fuel 2auge ecni 12 Fuel pump shut off switch 93 Fuse panels instrument panel ccee 95 power distribution box 98 FUSES e ere a ares ana 94 95 Gauges Mechanical engine coolant temperature BAUSEN r E R 13 Hazard flashers esceeseeeees 93 Headlamps ccccccecesssceeesseeeeees 16 daytime running lights 16 flashing neekin ane bees 17 Nish Pean osn 16 Heating seei cares tins tee aie 17 High beams indicator light 0 0 0 eee 9 HOO aae anaso a detected 111 Instrument panel lighting up panel and interior 17 Jump starting your vehicle 106 107 attaching cables 0 107 disconnecting cables 10
10. H have your vehicle checked at your dealership or by a qualified EA technician Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position If the pointer moves and stays outside the normal operating range as indicated have the vehicle s electrical system checked as soon as possible H ca 15 Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps only Rotate to the second position to also turn on the headlamps Ss Q Q 7 o Foglamp control if equipped Turn on the low beam headlamps and press the foglamp control to activate the foglamps The foglamp control will illuminate when the foglamps are on J amp Press the foglamp control a second time to deactivate the foglamps Daytime running lamps DRL if equipped Turns the highbeam headlamps on with a reduced output To activate e the engine must be running and e the headlamp control is in the OFF or Parking lamps position The Daytime Running Light DRL system will not illuminate the tail lamps and parking lamps Turn on your headlamps at dusk Failure to do so may result in a collision High beams Push forward to activate 16 Controls and features Flash to pass Pull toward you to activate and release to deactivate PANEL DIMMER CONTROL Use to adjust the brightness of the instrument
11. Keep the passenger air bag turned on unless there is a child seat installed in the front seat When the passenger air bag switch is turned off the passenger air bag will not inflate in a collision CHILDREN AND SAFETY BELTS Children who are too large for child safety seats as specified by your child safety seat manufacturer should always wear safety belts Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child s face or neck the child should wear the lap and shoulder belt Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit If the shoulder belt cannot be properly positioned e move the child to one of the seats with a lap belt only Gif equipped or e if the child is the proper size restrain the child in a safety seat 52 Seating and safety restraints Do not leave children unreliable adults or pets unattended in your vehicle To improve the fit of lap and shoulder belts on children who have outgrown child safety seats Ford recommends use of a belt positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards Belt positioning booster seats raise the child and provide a shorter firmer seating cushion that encourages safer seating posture and bett
12. NS ee J O TF i A O wy eS Wd ay The high current fuses are coded as follows Fuse Relay Fuse Amp ee 1 50A P Fuse Panel 2 par Blower Motor Relay 4 Wheel Anti Lock Brake System 4WABS Module 4 20A Power Windows _ __ _ _ 20A Electronic Shift Relay and Electronic Shift E a eee A 30 4 Wheel Anti lock Brake System 4WABS Module 99 Roadside emergencies Fuse Relay Fuse Am ae Main Light Switch and Multifunction Switch Heated Oxygen Sensor EGR Vacuum Regulator EVR Solenoid Camshaft Position Sensor CMP Canister Vent Solenoid Electronic Engine Controls Diode Mini Fuses Maxi Fuses bo A gt zi m 8s faoa BE A 13 15A BE ae Zooo e C Bo p C E C C T E J S f l C noo o e wooo a Ce Se Bo o o a o ae eee a al erie ete a 2 100 Roadside emergencies CHANGING THE TIRES If you get a flat tire while driving do not apply the brake heavily Instead gradually decrease your speed Hold the steering wheel firmly and slowly move to a safe place on the side of the road Temporary spare tire information Your vehicle may have a temporary or full size spare tire The temporary spare tire for your vehicle is labeled as such It is smaller than a regular tire and is designed for emergency use only Replace this tire with a full size tire as soon as possible It is not recommended that the vehicle be operated in 4WD
13. this range if at room temperature 10 C 35 C 50 F 95 F see figure C o to the right If your vehicle has been operated for an extended period at high speeds in city traffic during hot weather or pulling a trailer the vehicle should be turned off for about 30 minutes to allow the fluid to cool before checking KOON DOXXX XX IDON T ADD IF IN CROSSHATCH AREA YOO 1 Park the vehicle on a level surface and engage the parking brake 2 With the parking brake engaged and your foot on the brake pedal PRN 2 1 start the engine and move the gt gearshift lever through all of the gear ranges Allow sufficient time for each gear to engage 3 Latch the gearshift lever in P Park and leave the engine running 4 Remove the dipstick wiping it clean with a clean dry lint free rag 5 Install the dipstick making sure it is fully seated in the filler tube 6 Remove the dipstick and inspect the fluid level The fluid level should be within the top hole area on the dipstick 7 If necessary add fluid in 250ml 1 2 pint increments through the filler tube until the level is correct 8 If an overfill occurs excess fluid should be removed by a qualified technician An overfill condition of transmission fluid may cause shift and or engagement concerns and or possible damage If the fluid level is above the crosshatch hot operating range area after driving the vehicle for o approxim
14. a child in a child seat If you must use a forward facing child seat in the front seat move seat all the way back Air bag can kill or injure a child in a child seat Child seats should be never be placed in the front seats unless passenger air bag switch is turned off See Passenger air bag deactivation switch 2 Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together 55 Seating and safety restraints 3 While holding the shoulder and lap belt portions together route the tongue through the child seat according to the child seat manufacturer s instructions Be sure the belt webbing is not twisted 4 Insert the belt tongue into the proper buckle for that seating position until you hear and feel the latch engage Make sure the tongue is latched securely by pulling on it 5 To put the retractor in the automatic locking mode grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard a 6 Allow the belt to retract The belt will click as it retracts to indicate it is in the automatic locking mode 56 Seating and safety restraints 7 Pull the lap belt portion across the child seat toward the buckle and R pull up on the shoulder belt while pushing down with knee on the child seat 8 Allow the safety belt to retract to x remove any slack in the belt x gt 9 Before placing the child in the seat forc
15. and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course For example a tire grade 150 would wear one and one half 1 1 2 times as well on the government course as a tire grade 100 The relative performance of tires depends upon the actual conditions of their use however and may depart significantly from the norm due to variations in driving habits service practices and differences in road characteristics and climate Traction AB C The traction grades from highest to lowest are A B and C and they represent the tire s ability to stop on wet pavement as measured under test surfaces of asphalt and concrete A tire marked C may have poor traction performance The traction grade assigned to this tire is based on braking straight ahead traction tests and does not include cornering turning traction Temperature A B C The temperature grades are A the highest B and C representing the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sustained high temperature can cause the material of the tire to degenerate and reduce tire life and excessive temperature can lead to sudden tire failure The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Mo
16. and color Oamp Red S 50ampfuselink Red o E Passenger compartment fuse panel Ly The fuse panel is located on the left hand side of the instrument panel facing the driver s side door Pull the panel cover outward to access the fuses To remove a fuse use the fuse puller tool provided on the fuse panel cover 95 Roadside emergencies The fuses are coded as follows Fuse Relay Amp Description Location Rating 2 7 5A Blower Motor Relay PAD Module Air Bag Elen Diagnostic Monitor 6 Te CO NOTUSED Cd 7 is 97 7 Right Headlamp Fog Lamp Relay 7 Brake Pedal Position Switch 75A 10 7 Speed Control Servo Amplifier Assembly Generic Electronic Module GEM Shift Lock Actuator Blend Door Actuator A C Heater Assembly Turn Signals 96 5A 7 Right Stop Turn Trailer Tow Connector 5A 5A Roadside emergencies Fuse Fuse Relay Amp Description Location ise ern 11 7 5A Instrument Cluster Daytime Running Lights O O Somna e 2 NOTUSD S e an Brake Peat Postion Saitek 14 20A or 20A If equipped with Rear Anti Lock Brake 10A System RABS Module 10A If equipped with 4 Wheel Anti Lock Brake System 4WABS Module 4WABS Main Relay 16 30A Windshield Wiper Motor Wiper Hi Lo Relay Wiper Run Park Relay Driver s Unlock Relay All Unlock Relay All Lock Relay PCM Power Diode RAP Module Generic Electronic Module GEM Radio 283 ee Neb Used eS Clutch Pedal Pos
17. and eye injuries or internal injuries particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment Thus it is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control Several air bag system components get hot after inflation Do not touch them after inflation If the air bag is inflated the air bag will not function again and must be replaced immediately If the air bag is not replaced the unrepaired area will increase the risk of injury in a collision 49 Seating and safety restraints The SRS consists of e driver and passenger air bag modules which include the inflators and air bags e one or more impact and safing sensors passenger air bag deactivation switch and diagnostic monitor RCM e a readiness light and tone e and the electrical wiring which connects the components The RCM restraints control module monitors its own internal circuits and the supplemental air bag electrical system warning including the passenger air bag deactivation switch the impact sensors the system wiring the air bag system readiness light the air bag back up power and the air bag ignitors Determining if the system is operational The SRS uses readiness lights in the instrument cluster and the passenger air bag deactivate switch or a tone to indicate the condition of the system Refe
18. and features e lt A Floor Allows for maximum heating by distributing outside air through the floor ducts However the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode e TH Floor and defrost Distributes outside air through the windshield defroster ducts and the floor ducts Heating and air conditioning capabilities are provided in this mode For added customer comfort when the temperature control knob is anywhere in between the full hot and full cold positions the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers If the temperature is about 10 C 50 F or higher the air conditioner will automatically dehumidify the air to prevent fogging e Q Distributes outside air through the windshield defroster ducts It can be used to clear ice or fog from the windshield If the temperature is about 10 C 50 F or higher the air conditioner will automatically dehumidify the air to prevent fogging Operating tips e In humid weather select RY before driving This will prevent your windshield from fogging After a few minutes select any desired position e To prevent humidity buildup inside the vehicle don t drive with the climate control system in the OFF position e Don t put objects under the front seat that will interfere with the airflow to the back seats if equipped e Remove any snow ice o
19. and shoulder belts 40 41 42 MAINTENANCE ccc eeeececeeeeeeeteees 46 PIOPEr USE snenia nne 39 warning light and chime 11 5 46 Safety seats for children attaching with tether straps 57 tether anchorage hardware 58 DCALS EAE T TA A T 37 adjusting the seat manual 37 JUMP seats oec 38 39 lumbar support cece 38 rear seat ACCESS seei 38 Servicing your vehicle 110 precautions when servicing 110 Snowplowing seseecseeceereeerreree 2 Special notice diesel powered vehicles 3 utility type vehicles 000 2 Speed control 0 0 ceeeeeeeeeeee 24 Index canceling a set speed 27 indicator light eee 28 resuming a set speed o n 28 tap up tap GOWN cece 26 turing Off aen 25 Speedometer ccccccccessceeenes 14 Starting your vehicle 59 61 Tachometer mechanical cluster 006 13 Tilt steering wheel 29 ANE Site se ec sciacede AE 130 132 changing oo eee eeeeeeeeeeeeeeeeeees 103 checking the pressure 132 replacing pieccsetiives ian 133 rotating asinina yeaa 132 snow tires and chains 134 treadwear cccececesscccseesseseeeeaees 131 Traction lok rear axle 79 127 Trailer towing c eects 81 TDS seecead Sasectasshs bust setedatede EAT 89 Transaxle fluid checking and adding manual oe eeeeeeeeeceeeteeeeees 126 Transfer case fluid
20. area before driving Map out your route before driving in the area For more information on driving off road read the Four Wheeling supplement in your owner s portfolio If your vehicle gets stuck If the vehicle is stuck shift the transmission in a steady motion between forward and reverse gears Allow the transmission to engage then press lightly on the accelerator Do not rock the vehicle for more than a few minutes The transmission and tires may be damaged or the engine can overheat Do not spin the wheels at over 56 km h 85 mph The tires may fail and injure a passenger or bystander Sand When driving over sand try to keep all four wheels on the most solid area of the trail Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain Apply the accelerator slowly and avoid spinning the wheels 77 Driving Mud and water If you must drive through high water drive slowly Traction or brake capability may be limited When driving through water determine the depth avoid water higher than the bottom of the hubs if possible and proceed slowly If the ignition system gets wet the vehicle may stall Once through water always try the brakes Wet brakes do not stop the vehicle as effectively as dry brakes Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal After driving through mud clean off residue stuck to rotating
21. as the exterior of your vehicle Use glass cleaner or tar remover if necessary To avoid scratching the lamps do not use a dry paper towel chemical solvents or abrasive cleaners Cleaning the wiper blades If the wiper blades do not wipe properly clean the wiper blades with undiluted windshield wiper solution Clean the windshield with undiluted windshield wiper solution or a mild non abrasive detergent Rinse thoroughly with clean water To avoid damaging the blades do not use fuel kerosene paint thinner or other solvents 145 Maintenance and care Cleaning the instrument panel Clean with a damp cloth then dry with a dry cloth Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel The dull finish in this area helps protect the driver from undesirable windshield reflection Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner Remove fresh spots immediately Follow the directions that come with the cleaner Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets Do not bleach or dye the belts because these actions may weaken the belt webbing Check the safety belt system periodically to make sure there are no nicks wear or cuts If your vehicle has been involved in an accident refer to the Safety belt maintenance section in the Seating and safety r
22. down on the height adjustment assembly to make sure it is locked in place Position the shoulder belt height adjuster so that the belt rests across the middle of your shoulder Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a collision 43 Seating and safety restraints Lap belts Adjusting the front center seat lap belt if equipped The lap belt does not adjust automatically Adjust to fit snugly and as low as possible around your hips Do not wear the lap belt around your waist Insert the tongue into the correct N buckle To lengthen the belt turn 7 the tongue at a right angle to the 7 belt and pull across your lap until it reaches the buckle To tighten the belt pull the loose end of the belt through the tongue until it fits snugly across the hips Shorten and fasten the belt when not in use 44 Seating and safety restraints Adjusting the rear center facing jump seat lap belt if equipped The lap belts for rear center facing jump seat occupants have automatic retractors for the belt tongue and a fixed position buckle To fasten the belt pull the belt all the way across your hips and insert the tongue into the buckle on your rear door until you hear a snap and feel it latch Make sure the buckle is securely fastened by pulling on the tongue e Position the belt so that it fits snugly and as low as possible aro
23. harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Replacing the battery The transmitter is powered by one coin type three volt lithium battery CR2032 or equivalent Typical operating range will allow you to be up to 10 meters 33 feet away from your vehicle A decrease in operating range can be caused by e battery weakness due to time and use e weather conditions e nearby radio towers e structures around the vehicle e other vehicles parked next to the vehicle To replace the battery 1 Twist a thin coin between the two halves of the transmitter near the key ring DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART 2 Place the positive side of new battery in the same orientation Refer to the diagram inside the transmitter unit 3 Snap the two halves back together 33 Controls and features Replacing lost transmitters Take all your vehicle s transmitters to your dealer for reprogramming if e a transmitter is lost or e you want to purchase additional transmitters up to four may be programmed Reprogramming transmitters To reprogram all transmitters place the key in the ignition and switch from OFF to ON eight times in a row within 10 seconds After doors
24. in the OFF position e Don t put objects under the front seat that will interfere with the airflow to the jumper seats if equipped 18 Controls and features e Remove any snow ice or leaves from the air intake area at the bottom of the windshield under the hood e When placing objects on top of your instrument panel be careful to not place them over the defroster outlets These objects can block airflow and reduce your ability to see through your windshield Also avoid placing small objects on top of your instrument panel These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system Manual heating and air conditioning system if equipped Fan speed control Controls the volume of air circulated we in the vehicle C Temperature control knob Controls the temperature of the airflow inside the vehicle Y 19 Controls and features Mode selector control Controls the direction of the airflow eee to the inside of the vehicle The air conditioning compressor will operate in all modes except and mM However the air conditioning will only function if the outside temperature is about 10 C 50 F or above Since the air conditioner removes considerable moisture from the air during operation it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehic
25. m ft Regular Cab 3 0L 3 401 7 500 0 1 741 0 3 840 4 64 50 w v 3 0L 3 628 8 000 0 1 969 0 4 340 4 64 50 4 0L 3 401 7 500 0 1 724 0 3 800 4 64 50 4 0 3 73 4309 9 500 0 2 631 0 5 800 4 64 50 w YH Regular Cab Splash 3 0L 3 73 4 64 50 3 0L 4 64 50 4 0L 4 64 50 4 0L 0 2 613 0 5 760 4 64 50 SuperCab SuperCab Splash 3 0L 4 64 50 3 0L 4 64 50 4 0L 4 64 50 4 0L 4 64 50 For high altitude operation reduce GCW by 2 per 300 meters 1 000 ft of elevation For definition of terms used in this table see Vehicle loading earlier in this chapter To determine maximum trailer weight designed for your vehicle see Calculating the load earlier in this chapter Maximum trailer weight is shown The combined weight of the completed towing vehicle including hitch passengers and cargo and the loaded trailer must not exceed the Gross Combined Weight Rating GCWR WY YY HY WY 86 Driving Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage transmission axle damage structural damage loss of control and personal injury Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle See your dealer or a reliable trailer dealer if you require assistance Hitches For to
26. mishandled Observe the following guidelines when handling automotive fuel e Extinguish all smoking materials and any open flames before fueling your vehicle e Always turn off the vehicle before fueling e Automotive fuels can be harmful or fatal if swallowed If fuel is swallowed call a physician immediately even if no symptoms are immediately apparent The toxic effects of fuel may not be visible for hours e Fuels can also be harmful if absorbed through the skin If fuel is splashed on the skin promptly remove contaminated clothing and wash skin thoroughly with soap and water If fuel is splashed in the eyes remove contact lenses if worn flush with water for 15 minutes and seek medical attention 135 Maintenance and care e Be particularly careful if you are taking Antabuse or other forms of disulfiram for the treatment of alcoholism Breathing gasoline vapors or skin contact could cause an adverse reaction Consult a physician immediately Choosing the right fuel Use only UNLEADED FUEL The use of leaded fuel is prohibited by law and could damage your vehicle Your vehicle was not designed to use fuel or fuel additives with metallic compounds including manganese based compounds containing MMT Vehicles certified to California emission standards indicated on the underhood Vehicle Emissions Control Information label are designed to operate on California reformulated gasolines If California reformula
27. rear axles at low speeds 75 Driving Shifting from 2WD 2WD high to 4X4 HIGH 4WD High Move the 4WD control to the 4X4 _ gt HIGH x At temperatures below 0 C 32 F ewn KA LOW shifts from 2WD to 4X4 HIGH should not be performed above 72 km h 45 mph e Do not shift into 4X4 HIGH with the rear wheels slipping Shifting from 4X4 HIGH 4WD high to 2WD 2WD high Move the 4WD control to 2WD at a any forward speed You do not need KK AM aKa to put the gearshift in R Reverse De LW to disengage your front hubs Shifting between 4X4 HIGH 4WD high and 4X4 LOW 4WD low 1 Bring the vehicle to a stop 2 Depress the brake 3 Place the gearshift in N Neutral automatic transmission or depress the clutch manual transmission 4 Move the 4WD control to the 4X4 x HIGH or 4X4 LOW position 76 Driving Driving off road with 4WD Your vehicle is specially equipped for driving on sand snow mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles both on and off the road Maintain steering wheel control at all times especially in rough terrain Since sudden changes in terrain can result in abrupt steering wheel motion make sure you grip the steering wheel from the outside Do not grip the spokes Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps You should either know the terrain or examine maps of the
28. weight is 907 kg 2 000 Ibs For high altitude operation reduce GCW by 2 per 300 meters 1 000 ft elevation in this chapter vehicle see Calculating the load earlier in this chapter Maximum trailer weight is shown The combined weight of the completed towing vehicle including hitch passengers and cargo and the loaded trailer must not exceed the Gross Combined Weight Rating GCWR Trailer tow table 4x4 manual transmission Rear Maximum Maximum Maximum axle GCWR kg trailer frontal area of ratio Ibs weight kg Ibs trailer m ft Regular Cab 3 0L 3 73 2 721 6 000 0 1 080 0 2 380 Equal to frontal area of base vehicle 4 0L 3 27 2 721 6 000 0 907 0 2 000 Equal to frontal area of base vehicle 4 0L 3 73 3 175 7 000 0 1 515 0 3 340 Equal to frontal area of base vehicle 83 Driving 3 0L 4 64 50 4 0L 4 64 50 4 0L 3 73 3175 7 000 0 1 497 0 3 300 4 64 50 3 0 4 64 50 4 0L 4 64 50 4 0 0 1 442 0 3 180 4 64 50 3 0L 4 64 50 4 0L 4 64 50 4 0L 4 64 50 For high altitude operation reduce GCW by 2 per 300 meters 1 000 ft of elevation For definition of terms used in this table see Vehicle loading earlier in this chapter To determine maximum trailer weight designed for your vehicle see Calculating the load earlier in this chapter Maximum trailer weight is shown The combined weight of the completed towing vehicle including hitch pa
29. 0000 BARTINTTR TP PS TR AXLE XXX X XX X XX R SPR X XXXX T0000 UTC VFOHT 15294A10 GA AIR ren BA XXXXXXXXXXXXXXXXX The engine number the last eight numbers of the vehicle identification number is stamped on the engine block transmission frame and transfer case if equipped 154 Reporting safety defects REPORTING SAFETY DEFECTS U S ONLY If you believe that your vehicle has a defect that could cause a crash or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying Ford Motor Company If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer or Ford Motor Company To contact NHTSA you may either call the Auto Safety Hotline toll free at 1 800 424 9393 202 366 0123 in the Washington D C area or write to NHTSA U S Department of Transportation 400 Seventh Street Washington D C 20590 You can also obtain other information about motor vehicle safety from the Hotline 155 Index Aiming headlamps 06 142 Air bag supplemental restraint SYSTEM eire selavteainate R 47 and child safety seats 48 descripti m resad inae 47 d
30. 8 Keys key in ignition chime 11 Lamps interior lamps ccccceeeee 141 Lights warning and indicator All DAG erener koon ia atcha 8 anti lock brakes ABS 8 anti theft oo ce eeeeeeeeee 9 Brak 2 ios Hist Saltaire 8 charging system s 9 check engine sassen 6 7 cruise indicator 00 10 GOOF ajat ays tea hee aa 10 fuel reset resinen aa 8 overdrive Off oo eeeeeeeeee 9 Safety Delt oo cccescceeeseeeeees 8 turn signal indicator 0 9 Load limits trailer towing oeiee 81 Lubricant specifications 150 Manual transmission driving annsna 72 73 74 Mirrors Cleaning orire eons 146 side view mirrors power 31 Motorcraft parts cece 147 Odometer hreier 14 Index Off road driving 4 wheel drive 77 Overdrive hdres 28 Panic alarm feature remote entry System iesti e 33 Parking brake sasas 66 Power door locks cccceeeeees 31 Power steering fluid checking and adding 123 Rai nerina aE anaE 24 Recreational towing all wheels on the ground eee 89 Refill capacities for fluids 148 R l yS dictate aR REAN 94 Remote entry system 00 32 illuminated entry c cee 34 locking unlocking doors 32 replacement additional transmitters 0 0 ee eeeeete ees 34 replacing the batteries 33 Reporting safety defects 155 Safety restraints extension assembly 06 45 lap
31. Air bags can kill or injure a child in a child seat Child seats should never be placed in the front seats unless passenger air bag switch is turned off See Passenger air bag deactivate switch How does the air bag supplemental restraint system work The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system Rather it means the forces were not of the type sufficient to cause activation Air bags are designed to inflate in frontal and near frontal collisions not rollover side impact or rear impacts 48 Seating and safety restraints The air bags inflate and deflate rapidly upon activation After air bag deployment it is normal to notice a smoke like powdery residue or smell the burnt propellant This may consist of cornstarch talcum powder to lubricate the bag or sodium compounds e g baking soda that result from the combustion process that inflates the air bag Small amounts of sodium hydroxide may be present which may irritate the skin and eyes but none of the residue is toxic While the system is designed to help reduce serious injuries it may also cause minor burns abrasions swelling or temporary hearing loss Because air bags must inflate rapidly and with considerable force there is the risk of death or serious injuries such as fractures facial
32. DD FULL range 3 0L and 4 0L engine Oil levels above the MAX mark 2 5L engine or the letter F in FULL 3 0L and 4 0L engine may cause engine damage Some oil must be removed from the engine by a service technician 7 Put the indicator back in and ensure it is fully seated 116 Maintenance and care Adding engine oil 1 Check the engine oil For instructions refer to Checking the engine owl in this chapter 2 If the fluid level is not within the normal range add only certified engine oil of the preferred viscosity Add engine oil through the oil filler cap Remove the filler cap and use a funnel to pour oil in the opening 3 Recheck the oil level Make sure the oil level is not above the MAX mark or the letter F in FULL on the dipstick Engine oil and filter recommendations Look for this certification mark Motorcraft SAE 5W 30 MOTOR OIL QUART 0 946L Ford oil specification is WSS M2C153 G Use SAE 5W 30 motor oil certified for gasoline engines by the American Petroleum Institute Do not use supplemental engine oil additives oil treatments or engine treatments They are unnecessary and could under certain conditions lead to engine damage which is not covered by your warranty Change your engine oil and filter according to the appropriate schedule listed in the Service Guide Ford production and aftermarket Motorcraft oil filters are designed for added engine
33. EHICLE The gases around the battery can explode if exposed to flames sparks or lit cigarettes An explosion could result in injury or vehicle damage Do not push start your vehicle You could damage the catalytic converter Batteries contain sulfuric acid which burns skin eyes and clothing Preparing your vehicle Also see the label on the battery 1 Use only a 12 volt supply to start your vehicle If you connect your battery to a 24 volt power supply you can damage your starter ignition system and other electrical components 2 Do not disconnect the battery of the disabled vehicle as this could damage the vehicle s electrical system 3 Park the booster vehicle close to the hood of the disabled vehicle making sure they do not touch Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts 4 Check all battery terminals and remove any excessive corrosion before you attach the battery cables 5 Turn the heater fan on in both vehicles to protect any electrical surges Turn all other accessories off 106 Roadside emergencies Connecting the jumper cables 1 Position the vehicles so that they do not touch one another 2 Switch off the engine Switch off any unnecessary electrical equipment 3 Connect the positive terminal of the discharged battery 1 to the positive terminal of the booster battery 2 4 Connect one end of the second lead t
34. LDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child Carefully follow all of the manufacturer s instructions with the safety seat you put in your vehicle If you do not install and use the safety seat properly the child may be injured in a sudden stop or collision When installing a child safety seat e Use the correct safety belt buckle for that seating position e Make sure the tongue is securely fastened in the buckle e Keep the buckle release button pointing up and away from the safety seat with the tongue between the child seat and the release button to prevent accidental unbuckling Place seat back in upright position e Put the safety belt in the automatic locking mode Refer to Automatic locking mode Ford recommends the use of a child safety seat having a top tether strap Install the child safety seat in a seating position which is capable of providing a tether anchorage For more information on top tether straps refer to Attaching safety seats with tether straps Carefully follow all of the manufacturer s instructions included with the safety seat you put in your vehicle If you do not install and use the safety seat properly the child may be injured in a sudden stop or collision 54 Seating and safety restraints 1 Position the child safety seat in a seat with a combination lap and shoulder belt Air bag can kill or injure
35. ONSOLE IF EQUIPPED Your vehicle may be equipped with a variety of console features These include e utility compartment with cassette compact disc storage e auxiliary power point e cupholders e coin holder slots e ashtray e flip up armrest 31 Controls and features Use only soft cups in the cupholder Hard objects can injure you in a collision REMOTE ENTRY SYSTEM IF EQUIPPED The remote entry system allows you to lock or unlock all vehicle doors without a key The remote entry features only operate with the ignition in the OFF position Unlocking the doors Press this control to unlock the driver door The interior lamps will illuminate Press the control a second time within five seconds to unlock all doors Locking the doors Press this control to lock all doors To confirm all doors are closed and locked press the control a second time within five seconds The doors will lock again the horn will chirp and the lamps will flash If any of the doors are ajar the horn will make two quick chirps reminding you to properly close all doors 32 Controls and features Sounding a panic alarm Press this control to activate the alarm To deactivate the alarm press the control again or turn the ignition to ACC or ON This device complies with part 15 of the FCC rules and with RS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause
36. QUIPPED When Four wheel drive 4WD is engaged power is supplied to all four wheels through a transfer case 4WD power can be selected when additional driving power is desired All utility type vehicles and 4WD vehicles have special design and equipment features to make them capable of performing in a wide variety of off road applications Specific design characteristics give them higher centers of gravity than ordinary passenger cars 74 Driving Utility and four wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low slung sports cars are designed to perform satisfactorily under off road conditions Avoid sharp turns or abrupt maneuvers in these vehicles AWD operation is not recommended on dry pavement Doing so could result in difficult disengagement of the transfer case increased tire wear and decreased fuel economy 4WD system indicator lights The 4WD system indicator lights illuminate only under the following conditions If these lights illuminate during normal driving have your vehicle serviced e 4WD HIGH illuminates when iH GND High Backes 4W D HIGH e 4WD LOW illuminates when oa 4W D LOW Using the electronic shift 4WD system if equipped Positions of the electronic shift system 2WD 2WD High Power to rear axle only 4X4 HIGH 4WD High Power delivered to front and rear axles for increased traction 4X4 LOW 4WD Low Power to front and
37. SRS precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module K IN All occupants of the vehicle including the driver should always properly wear their safety belts even when air bag SRS is provided Always transport children 12 years old and under in the back seat and always use appropriate child restraints NHTSA recommends a minimum distance of at least ten 10 inches between an occupant s chest and the air bag module 47 Seating and safety restraints The right front passenger air bag is not designed to restrain occupants in the center front seating position Do not put anything on or over the air bag module Placing objects on or over the air inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury Do not attempt to service repair or modify the Air Bag Supplemental Restraint System or its fuses See your Ford or Lincoln Mercury dealer Children and air bags For additional important safety information read all information on safety restraints in this guide Children must always be properly restrained Failure to follow these instructions may increase the risk of injury in a collision
38. a downhill you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed If your vehicle slows down more than 16 km h 10 mph below your set speed on an uphill your speed control will disengage This is normal Pressing RES RSM RESUME will re engage it Do not use the speed control in heavy traffic or on roads that are winding slippery or unpaved 25 Controls and features To set a higher set speed You can accelerate with the accelerator pedal at any time during speed control usage Releasing the accelerator pedal will return your vehicle to Press and hold SET ACC SET ACCEL Release the control when the desired vehicle speed is reached or Press and release SET ACC SET ACCEL Each press will increase the set speed by 1 6 km h 1 mph or Accelerate with your accelerator pedal then press and release SET ACC SET ACCEL the previously programmed set speed To set a lower set speed 26 Press and hold CST COAST Release the control when the desired speed is reached or Press and release CST COAST Each press will decrease the set speed by 1 6 km h 1 mph or Depress the brake pedal When the desired vehicle speed is reached press SET ACC SET ACCEL To disengage speed control e Depress the brake pedal or e Depress the clutch pedal if equipped Disengaging the speed control will not erase the previously programmed set speed Pressing OFF will erase the p
39. acity 2 5L 6 2L 6 5 quarts without air conditioning Coolant capacity 2 5L 6 8L 7 2 quarts with air conditioning Coolant capacity 3 0L 9 0L 9 5 quarts without air conditioning Coolant capacity 3 0L 9 6L 10 2 quarts with air conditioning Coolant capacity 4 0L 7 4L 7 8 quarts without air conditioning Coolant capacity 4 0L 8 1L 8 6 quarts with air conditioning Power steering fluid capacity Fill to range on dipstick Manual transmission fluid capacity 2 65L 2 8 quarts Automatic transmission fluid 9 0L 9 5 quarts capacity 4x2 vehicles Automatic transmission fluid 9 3L 9 8 quarts capacity 4x4 vehicles 159 Filling station information Ensure correct automatic transmission fluid is used for a specific application Check the container to verify the fluid is MERCON and or MERCON V approved Some fluids have been approved as meeting both MERCON and MERCON V requirements and will be labeled as such Fluids labeled as meeting only MERCON or only MERCON V requirements must not be used interchangeably DO NOT mix MERCON and MERCON V Transmission fluid requirements are indicated on the dipstick or on the dipstick handle Refer to your Service Guide to determine the correct service interval 160
40. amps Trailer lamps are required on most towed vehicles Make sure your trailer lamps conform to local and Federal regulations See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps Using a step bumper The optional step bumper is equipped with an integral hitch and requires only a ball with a 19 mm 8 4 inch shank diameter The bumper has a 907 kg 2 000 Ib trailer weight and 91 kg 200 lb tongue weight capability The rated capcities as shown in this guide for trailer towing with the factory bumper are only valid when the trailer hitch ball is installed directly into the ball hole in the bumper Addition of bracketry to either lower the ball hitch position or extend the ball hitch rearward will significantly increase the loads on the bumper and its attachments This can result in the failure of the bumper or the bumper attachments Use of any type of hitch extensions should be considered abuse Driving while you tow Do not drive faster than 88 km h 55 mph when towing a trailer Speed control may shut off if you are towing on long steep grades When towing a trailer e Use a lower gear when towing up or down steep hills This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling e Anticipate stops and brake gradually Servicing after towing If you tow a trailer for long distances your vehicle will require more frequent s
41. ate STARTING THE ENGINE 1 Turn the key to 5 START lt without pressing the accelerator pedal and release as soon as the 3 4 engine starts The key will return to 4 ON D x 61 Starting 2 If the engine does not start within five seconds wait ten seconds and try again 3 If the engine does not start in two attempts or if the temperature is below 12 C 10 F depress the accelerator and start the engine while holding the accelerator down Release the accelerator when the engine starts 4 After idling for a few seconds apply the brake and release the parking brake Using the engine block heater if equipped An engine block heater warms the engine coolant which improves starting warms up the engine faster and allows the heater defroster system to respond quickly Use of an engine block heater is strongly recommended if you live in a region where temperatures reach 23 C 10 F or below Your engine block heater also comes with a battery warmer The battery warmer wraps around the battery and keeps the battery warm when the engine block heater is plugged in For best results plug the heater in at least three hours before starting the vehicle Using the heater for longer than three hours will not harm the engine so the heater can be plugged in the night before starting the vehicle To prevent electrical shock do not use your heater with ungrounded electrical systems or two pronged cheater adapt
42. ately 30 km 20 miles excess transmission fluid should be removed by a qualified technician KOONI r R DON T ADD IF IN CROSSHATCH AREA 125 Maintenance and care Checking and adding manual transmission fluid 1 Clean the filler plug 2 Remove the filler plug and inspect the fluid level 3 Fluid level should be at bottom of the opening 4 Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening am 5 Install and tighten the fill plug Use only fluid that meets Ford specifications Refer to the Capacities and specifications chapter 126 Maintenance and care Checking and adding transfer case fluid 1 Clean the filler plug 2 Remove the filler plug and inspect the fluid level 3 Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening Use only fluid that meets Ford specifications Refer to the Capacities and specifications chapter DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication If the original universal joints are replaced with universal joints equipped with grease fittings lubrication will also be necessary 127 Maintenance and care BATTERY Your vehicle may be equipped with a Superstart maintenance free battery If the original equ
43. atic Ford Extended 2 5L 14 engine DEX COOL with A C 3 0L V6 engine 9 0L 9 5 quarts Eee ie 3 0L V6 engine 9 6L 10 2 quarts fee tp 4 0L V6 engine 7 4L 7 8 quarts iene ene 4 0L V6 engine 8 1L 8 6 quarts fee eee 148 Capacities and specifications Name N A Fuel tank Regular cab Short wheel 62 8L 16 6 gallons base Regular cab 75 7L 20 0 gallons Long wheel base 74 2L 19 6 gallons Transfer Warner 13 54 4x4 Vehicles Front axle Motorcraft SAE 4x4 vehicles with fluid 80W90 Axle 2 5L I4 or 3 0L 1 4L 1 5 quarts Lubricant V6 engine 4x4 vehicles with 1 7L 1 8 quarts 4 V6 engine 2 4 2 6L 2 5 2 65 quarts Rear axle Motorcraft SAE fluid 80W90 Rear Axle Lubricant Windshield Ultra Clear washer fluid Windshield Fill to line on Washer reservoir Concentrate 1 Add 118 ml 4 oz of additive friction modifier C8AZ 19B546 A Ford specification EST M2C118 A for complete refill of Traction Lok axles Service refill capacities are determined by filling the rear axle 6 mm to 14 mm 1 4 inch to 9 16 inch below the bottom of the filler hole 149 Capacities and specifications LUBRICANT SPECIFICATIONS Ford part name or equivalent Motorcraft SAE 80W90 Rear Axle Lube High Performance DOT 3 Motor 75W90 Gear XY ae Rear axle Brake fluid and clutch fluid Ford part Ford number WSP M2C201 A WSL M2C192 A FITZ 19580 B C6AZ 19542 AB Vehi
44. ats between jump seats and underneath jack and tool covers Removing the spare tire 1 Assemble the jack handle to the lug wrench as shown in the illustrations When connecting the jack handle assemble the following e one handle extension and one a typical extension To assemble slide parts together To gt gt disconnect depress button and pull apart e one wheel nut wrench Depress C button and slide together 102 Roadside emergencies 2 Insert the straight end of the jack handle into the rear access hole located just above the rear bumper and below the tailgate Forward motion will stop and resistance to turning will be felt when properly engaged 3 Turn the handle counterclockwise until tire is lowered to the ground and the cable is slightly slack 4 Remove the retainer from the spare tire Stowing the spare 1 Lay the tire on the ground with the valve stem facing up 2 Install the retainer through the wheel center and slide the wheel under the vehicle 3 Turn the spare handle clockwise until the tire is raised to its original position underneath the vehicle The spare handle ratchets when the tire is raised to the stowed position It will not allow you to overtighten 4 If your vehicle is equipped with P265 75 R15 AT tires do not stow a flat or inflated full size spare tire in the spare tire carrier The flat full size tire should be stowed and tied down in the pickup b
45. be cleaned with rubbing alcohol before being used To remove the headlamp bulb 1 Make sure headlamp switch is in OFF position then open the hood If you are replacing the driver side headlamp unclip the electronic module on the right side of the battery and move it out of the way 2 Locate the headlamp bulb through the hole in the upper radiator support assembly 3 Disconnect the electrical connector from the bulb by pulling the connector rearward 4 Remove the bulb retaining ring by rotating it counterclockwise when viewed from the rear about an eighth of a turn to free it from the bulb socket and by sliding the ring off the plastic base Keep the ring because it will be used again to retain the new bulb 140 Maintenance and care 5 Remove the old bulb from its socket by gently pulling it straight back out of the socket Do not turn the bulb while removing it To install the new bulb 1 With the flat side of the bulb s plastic base facing upward insert the glass end of the bulb into the socket You may need to turn the Ae bulb left or right to line up the Ej we grooves in the plastic base with the gt tabs in the socket When the grooves are aligned push the bulb into the socket until the plastic base contacts the rear of the socket 2 Slip the bulb retaining ring over the plastic base until it contacts the rear of the socket by rotating it clockwise until you feel a stop 3 Push th
46. check the engine cooling system for leaks if you have to add more than 1 0 liter 1 0 quart of engine coolant per month Severe winter climate If you drive in extremely cold climates less than 36 C 34 F it may be necessary to increase the coolant concentration above 50 Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle is such that the coolant will not freeze at the temperature level in which you drive during winter months Never increase the engine coolant concentration above 60 Leave a 50 50 mixture of engine coolant and water in your vehicle year round in non extreme climates CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid at least twice a year If adding fluid is necessary use only MERCON ATF 1 Start the engine and let it run until it reaches normal operating temperature the engine coolant temperature gauge will be near the center of the NORMAL band 2 While the engine idles turn the steering wheel left and right several times 3 Turn the engine off 123 Maintenance and care 4 Check the fluid level on the dipstick It should be between the arrows in the FULL HOT range Do not add fluid if the level is within this range 5 If the fluid is low add fluid in small amounts continuously checking the level until it reaches the FULL HOT range Be sure to put the dipstick back in the reservoir TRANSMISSION FLUID Checking and ad
47. checking 127 158 Transmission ceeeeeeeeeeeeeeeee 124 automatic operation 67 68 69 70 71 72 fluid checking and adding AULOMALIC 2 enk aS 124 Trip Odometer cceecceseeeeeeees 14 Turn signal leye ihya ines N a 24 Vehicle dimensions 0 66 152 Vehicle Identification Number CVAD ist nis cota T te E 154 Vehicle loading cc eee 79 Ventilating your vehicle 63 Windows power windows operating 30 Windshield washer fluid and wipers checking and adding fluid 120 checking and replacing wiper e E el lt ane eee ene eee 129 operation sssssssssssssssseessssessee 29 Wrecker towing secsec 109 Filling station information Recommended fuel Unleaded fuel only 87 octane Fuel tank capacity 62 8L 16 6 gallons Regular cab Short wheel base Fuel tank capacity 75 7 20 0 gallons Regular cab Long wheel base Fuel tank capacity SuperCab 74 2L 19 6 gallons Engine oil capacity 4 3L 4 5 quarts Use Motorcraft with filter change 5W30 Super Premium Motor Oil 2 5L and 3 0L engines Ford Specification WSS M2C153 G Engine oil capacity 4 7L 5 0 quarts Use Motorcraft with filter change 5W30 Super Premium Motor Oil 4 0L engine Ford Specification WSS M2C153 G Tire size and pressure See Safety Compliance Certification Label on inside of driver door Hood release Pull handle under the left side of the instrument panel Coolant cap
48. cle Brake Fluid Ford Extended Life Engine Coolant DEX COOL Motorcraft 5W30 Super Premium Motor Oil Gf equipped F6AZ 19544 AA or Engine coolant B XO 5W30 BSP or QSP Engine oil Multi Purpose DOAZ 19584 AA or F5AZ 19g209 AA Hinges latches stricker plates fuel filler door hinge and seat tracks Transmission steering parking brake linkages and pivots brake and clutch pedal shaft clutch pilot bearing and input shaft spline manual transmission M1C75 B 150 Capacities and specifications Ford part Ford part Ford Item name or 2 fem O equivalent Power steering fluid Motorcraft XT 2 QDX MERCON transfer case fluid and MERCON transmission fluid ATF manual Automatic transmission AA AT5 QM MERCON V 4R44E and 5R55E ate Ultra clear C9AZ ESR Windshield washer fluid windshield 19550 AB M17P5 A washer concentrate 1 Add 118 ml 4 oz of additive friction modifier C8AZ 19B546 A Ford specification EST M2C118 A for complete refill of Traction Lok axles ENGINE DATA Engine 2 5L I4 engine 3 0L V6 engine 4 0L V6 engine Cubic inches Horsepower 119 5000 rpm 50 5000 rpm 60 4200 rpm 3000 rpm 3250 rpm 2750 rpm Required fuel 87 octane grade Firing order _ 1 3 4 2 1 4 2 5 3 6 Spark plug 1 07 1 17 mm 1 07 1 17 mm 1 3 1 4 mm Ignition EDIS EDIS EDIS Compression 9 4 1 9 14 1 9 0 1 ratio i 151 Capacities and specifications VEHICLE DIMENSIONS
49. ding automatic transmission fluid Follow the scheduled service intervals outlined in the Service Guide Before adding any fluid make sure the correct type is used The type of fluid used is normally indicated on the dipstick and or dipstick handle and also in the Lubricant specifications section in the Capacities and specifications chapter An overfill condition of transmission fluid may cause shift and or engagement concerns and or possible damage Do not drive the vehicle if the fluid 4 level is below the bottom hole on the dipstick and outside Boon ano IF IN CROSSHATCH AREA temperatures are above 10 C 50 F see figure to the right Your transmission does not use up fluid However it is recommended that you check the transmission fluid at least twice a year The fluid level should be checked if the transmission is not working properly i e if the transmission slips or shifts slowly or if you notice some sign of fluid leakage Transmission fluid should be checked at normal operating temperatures 66 C 77 C 150 F 170 F on a level surface The normal operating temperature can be reached after approximately 32 km 20 miles of driving The transmission fluid should be in this range if at normal operating temperature 66 C 77 C o 150 F 170 F see figure to the right YY OY REAL DON T ADD IF IN CROSSHATCH AREA 124 Maintenance and care The transmission fluid should be in
50. driveshafts and tires Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components If the transmission and transfer case are submerged in water their fluids should be checked and changed if necessary Water intrusion into the transmission may damage the transmission If the rear axle is submerged in water the rear axle lubricant should be checked and changed if necessary The rear axle is filled with a synthetic lubricant and does not normally require a lubricant change for the life of the vehicle Rear axle lubricant quantities should not need to be checked unless a leak is suspected Driving on hilly or sloping terrain When driving on a hill avoid driving crosswise or turning on steep slopes You could lose traction and slip sideways Drive straight up straight down or avoid the hill completely Know the conditions on the other side of a hill before driving over the crest When climbing a steep hill start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started This reduces strain on the engine and the possibility of stalling When descending a steep hill avoid sudden braking Rapid pumping of the brake pedal will help slow the vehicle and still maintain steering control When speed control is on and you are driving uphill your vehicle speed may drop considerably especially if you are carrying a heavy load If vehicle speed drop
51. e accomplished with the rear driveshaft removed by using the front drive to propel the vehicle To operate the vehicle in this condition you must follow these guidelines Place the transfer case in 4WD by rotating the 4WD control to 4WD HIGH Drive the vehicle only on good surface roads to avoid excessive loads on the front wheel drive system Maximum speed is 56 km h 85 mph Maximum distance is 80 km 50 miles Avoid quick acceleration and steep grades To return the vehicle to a towable condition you must place the transfer case in 2WD by rotating the 4WD control to 2WD Both the 4WD HIGH and 4WD LOW indicator lights in the instrument cluster will be off when the 4WD control is in 2WD In addition it is recommended that you follow the instruction provided by the manufacturer of the towing apparatus 91 Driving CAMPER BODIES Your Ranger Pickup is not recommended for slide in camper bodies FUEL CONSUMPTION Fuel economy can be improved by avoiding e lack of regular scheduled maintenance e excessive speed e rapid acceleration e extended idle 92 Roadside emergencies HAZARD LIGHTS CONTROL Use only in an emergency to warn traffic of vehicle breakdown approaching danger etc The hazard flashers can be operated when the ignition is off e The hazard lights control is located on top of the steering column e Depress hazard lights control to activate all hazard flashers simultaneously e Depr
52. e electrical connector into the rear of the plastic base until it snaps locking it into position 4 Turn the headlamps on and make sure they work properly If the headlamp was correctly aligned before you changed the bulb you should not need to align it again REPLACING THE INTERIOR BULBS Check the operation of the following interior bulbs frequently e interior overhead lamp e map lamp Using the right bulbs Function Number of Trade bulbs number Park turn side marker lamps front 3157 Headlamps CSC rLSCOCOC SC C SNSCLSC C amp O Foglamps if equipped PCT B Himount brakelamp _ _ 2 6 Rear stop taillamps 2 3157 Rear turn lamps 2 O 36 Rear license plate lamps 2 1 Maintenance and care bulbs number 3156 212 2 To replace all instrument panel lights see your dealer AIMING THE HEADLAMPS The alignment of your headlamps should be checked by a qualified service technician if Map dome Regular Cab if equipped Map dome SuperCab if equipped 1 Oncoming motorists frequently signal you to deactivate your high beams and your high beams are not activated 2 The headlamps do not seem to provide enough light for clear night vision 3 The headlamp beams are pointed substantially away from a slightly down and to the right position CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance Guide for a list of Ford approved cleaner
53. e information refer to the Seating and safety restraints chapter Brake system warning Momentarily illuminates when the ignition is turned to the ON position O and the engine is off Also BRAKE illuminates when the parking brake is engaged Illumination after releasing the parking brake indicates low brake fluid level Anti lock brake system ABS Momentarily illuminates when the ignition is turned to the ON position and the engine is off If the light remains on continues to flash or fails to illuminate have the system serviced immediately Instrumentation Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on If one or both of the a indicators stay on continuously check for a burned out turn signal bulb Refer to Exterior bulbs in the Maintenance and care chapter High beams Illuminates when the high beam headlamps are turned on D Alarm system if equipped Illuminates when the alarm system is pre arming and flashes when the alarm system is active Refer to THEFT Perimeter alarm system in the Controls and features chapter Charging system Illuminates when the ignition is turned to the ON position and the engine is off The light also illuminates when the battery is not charging properly requiring electrical system service O D off if equipped Illuminates when the transmission control switch has been pushed O D When the light is o
54. er fit of lap and shoulder belts on the child A belt positioning booster should be used if the shoulder belt rests in front of the child s face or neck or if the lap belt does not fit snugly on both thighs or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion You may wish to discuss the special needs of your child with your pediatrician Important child restraint precautions You are required by law to use safety restraints for children in the U S and Canada If small children ride in your vehicle generally children who are four years old or younger and who weigh 18 kg 40 lbs or less you must put them in safety seats made especially for children Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision Always follow the instructions and warnings that come with any infant or child restraint you might use When possible place children in the rear seat of your vehicle Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position A Do not install a child seat in a center facing jump seat 53 Seating and safety restraints SAFETY SEATS FOR CHI
55. ers 62 Starting Guarding against exhaust fumes Although odorless and colorless carbon monoxide is present in exhaust fumes Take precautions to avoid its dangerous effects If you ever smell exhaust fumes of any kind inside your vehicle have your dealer inspect and fix your vehicle immediately Do not drive if you smell exhaust fumes These fumes are harmful and could kill you Have the exhaust and body ventilation systems checked whenever e the vehicle is raised for service e the sound of the exhaust system changes e the vehicle has been damaged in a collision Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time open the windows at least 2 5 cm one inch Adjust the heating or air conditioning if equipped to bring in fresh air Improve vehicle ventilation by keeping all air inlet vents clear of snow leaves and other debris 63 Driving BRAKES Your brakes are self adjusting Refer to the Service Guide for scheduled maintenance Occasional brake noise is normal and often does not indicate a performance concern with the vehicle s brake system In normal operation automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied Such noises are usually heard during the first few brake applications in the morning however they may be heard at any time while braking and can be a
56. ervice intervals Refer to the Severe Duty Schedule in your Service Guide for more information 88 Driving Trailer towing tips e Practice turning stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination When turning make wider turns so the trailer wheels will clear curbs and other obstacles e Allow more distance for stopping with a trailer attached e The trailer tongue weight should be 10 15 of the loaded trailer weight e After you have traveled 80 km 50 miles thoroughly check your hitch electrical connections and trailer wheel lug nuts e When stopped in traffic for long periods of time in hot weather place the gearshift in P Park automatic transmissions or 1 First manual transmissions and increase idle speed This aids engine cooling and air conditioner efficiency e Vehicles with trailers should not be parked on a grade If you must park on a grade place wheel chocks under the trailer s wheels Launching or retrieving a boat When backing down a ramp during boat launching or retrieval e Do not allow the static water level to rise above the bottom edge of the rear bumper and e Do not allow waves to break higher than 15 cm six inches above the bottom edge of the rear bumper Exceeding these limits may allow water to enter critical vehicle components adversely affecting driveability emissions and reliability If the rear axle is subme
57. ess control again to turn the flashers off FUEL PUMP SHUT OFF SWITCH GASOLINE ENGINES ONLY If the engine cranks but does not start after a collision the fuel pump shut off switch may have been activated A Fuel Reset indicator light may illuminate in the instrument cluster The shut off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt 1 Turn the ignition to the OFF position 2 Check the fuel system for leaks 3 If no fuel leak is apparent reset the fuel pump shut off switch by pushing in the button on the switch 4 Turn the ignition to the ON position Pause for a few seconds and return the key to the OFF position 5 Make a further check for leaks in the fuel system 93 Roadside emergencies The fuel pump shut off switch is located in the passenger s foot well behind the kick panel FUSES AND RELAYS Fuses If electrical components in the vehicle are not working a fuse may have blown Blown fuses are identified by a broken wire within the fuse Check the appropriate fuses before replacing any electrical components Always replace a fuse with one that has the specified amperage rating Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire 94 Roadside emergencies Standard fuse amperage rating
58. estraints chapter Underbody Flush the complete underside of vehicle frequently Keep body drain holes unplugged Inspect for road damage Inside windows Use glass cleaner for the inside windows if they become fogged Cleaning mirrors Do not clean your mirrors with a dry cloth or abrasive materials Use a soft cloth and mild detergent and water Be careful when removing ice from outside mirrors because you may damage the reflective surface 146 Capacities and specifications MOTORCRAFT PART NUMBERS Component Air filter Fuel filter Battery Oil filter PCV valve Spark plugs AWSF 32F AWSF 32PP AGSF 22PP spark plug gap information Tf any spark plug needs to be removed for inspection it must be re installed in the same cylinder Cylinders No 1 2 and 3 have a PG suffix Cylinders No 4 5 and 6 have a P suffix If any spark plug needs to be replaced use only spark plugs with the service part number suffix letters PP as shown on the engine decal 147 Capacities and specifications REFILL CAPACITIES Ford Part Application Capacity Name Engine oil Motorcraft 2 5L I4 and 3 0L includes 5W30 Super V6 engine 4 3L 4 5 quarts garg 0 Brake fluid High All Performance DOT 3 Motor Vehicle Brake Fluid Motorcraft MERCON ATF Fill to line on reservoir Fill to range on dipstick Transmission Motorcraft 5 speed manual Motorcraft 4x2 vehicles with 9 0L 9 5 quarts autom
59. ety belt properly 39 Seating and safety restraints Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair 1 Use the shoulder belt on the outside shoulder only Never wear the shoulder belt under the arm 2 Never swing it around your neck over the inside shoulder 3 Never use a single belt for more than one person On four door SuperCab vehicles do not open the rear door when the rear seat belt is still buckled Combination lap and shoulder belts 1 To fasten insert the tongue into the slot in the buckle a a a a S O i 2 To unfasten push the red release button and remove the tongue from the buckle XN 7 a a The front outboard safety restraints in the vehicle are combination lap and shoulder belts The front passenger outboard safety belt has two types of locking modes described below 40 Seating and safety restraints Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement For example if the driver brakes suddenly or turns a corner sharply or the vehicle receives an impact of 8 km h 5 mph or more the combination safety belts will lock to help reduce forward movement of the driver and passengers In this mode the shoulder belt is automatically pre locked The belt wil
60. facturer s recommendation unlimited distance 4WD Electronic shift transfer case e Release the parking brake and place transmission in the neutral position e Shift the transfer case to 2H 2WD high Both the 4WD HIGH and 4WD LOW indicator lights in the instrument cluster will be off when the 4WD control is in 2WD For automatic transmissions maximum speed is 56 km h 85 mph and maximum distance is 80 km 50 miles e If you must exceed the distance or 80 km 50 miles and or speed of 56 km h 85 mph you must remove the rear driveshaft Mark the 90 Driving driveshaft and axle flanges to ensure proper position when reconnecting the driveshaft Refer to the Workshop Manual for proper fastener torque specifications When disconnecting installing the driveshaft the parking brake must be set and the wheels blocked to ensure the vehicle does not roll When the driveshaft is disconnected the maximum speed is 88 km h 55 mph and the distance is unlimited If you must exceed the distance or 80 km 50 miles and or speed of 56 km h 85 mph you must remove the rear driveshaft Mark the driveshaft and axle flanges to ensure proper position when reconnecting the driveshaft Refer to the Workshop Manual for proper fastener torque specifications For manual transmissions maximum speed is 88 km h 55 mph and distance is unlimited Limited vehicle operation such as driving the vehicle at a campsite can b
61. ge from any Ford dealer A Do not install a child seat in a center facing jump seat Tether anchorage hardware Tether anchorage hardware kits part number 613D74 including instructions may be obtained at no charge from any Ford or Lincoln Mercury dealer Tighten the anchor according to specifications Otherwise the safety seat may not be properly secured and the child may be injured in a sudden stop or collision 58 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system This system meets all Canadian Interference Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise When starting a fuel injected engine avoid pressing the accelerator before or during starting Only use the accelerator when you have difficulty starting the engine For more information on starting the vehicle refer to Starting the engine in this chapter Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system creating the risk of fire or other damage Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire Do not start your vehicle in a closed garage or in other enclosed areas Exhaust fumes can be toxic Always open the garage door before you start the engine See Guarding against exhaust fumes i
62. ggravated by environmental conditions such as cold heat moisture road dust salt or mud If a metal to metal continuous grinding or continuous squeal sound is present while braking the brake linings may be worn out and should be inspected by a qualified service technician Rear anti lock brake system RABS Rear Anti lock Brake System RABS is standard equipment on this vehicle RABS is designed to help you maintain directional stability in emergency stopping situations With RABS the rear brakes are kept from locking during panic stops however the front wheels can lock because they are not controlled by RABS You should apply the brakes with steadily increasing force as if squeezing the brakes If you feel the front wheels begin to lock momentarily release the pedal and repeat the squeeze technique Whenever the front wheels lock the vehicle cannot be steered A clicking noise and slight pedal pulsation during RABS braking events indicates the RABS is functioning Pedal pulsation coupled with clicking noise while braking under panic conditions on loose gravel wet or snowy roads is normal and indicates proper functioning of the vehicle s RABS If the vehicle has continuous vibration or shudder while braking felt mainly in the steering wheel the vehicle most likely needs service The RABS operates by detecting the onset of rear wheel lockup during brake applications and compensating for this tendency
63. he performance of your vehicle We recommend the use of gasolines that meet the AAMA specification if they are available It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high quality fuel Cleaner air Ford approves the use of gasolines to improve air quality including reformulated gasolines that contain oxygenates up to 10 ethanol or 15 MTBE Do not use gasolines containing methanol which can damage critical fuel system components Damage resulting from the use of methanol may not be covered by your warranty Running out of fuel Avoid running out fuel because this situation may have an adverse affect on powertrain components If you have run out of fuel You may need to crank the engine several times before the system starts to pump fuel from the tank to the engine If you run out of fuel your Check Engine light may come on For more information on the Check Engine light refer to the Instrumentation chapter Calculating fuel economy To accurately calculate your vehicle s fuel economy 1 Fill the tank completely and record the initial odometer reading 2 Each time you fill the tank record the amount of fuel added in liters or gallons 3 After at least three to five fuel tank fill ups fill the fuel tank and record the current mileage reading 4 Use one of the following equations to calculate fuel economy Liters used x 100 Total kilometers traveled Total miles
64. ibly tilt the seat forward and back to make sure the seat is securely held in place A 10 Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode you should not be able to pull more belt out If the retractor is not locked unbuckle the belt and repeat steps two through nine Check to make sure the child seat is properly secured before each use Attaching safety seats with tether straps Some manufacturers make safety seats that include a tether strap that goes over the back of the vehicle seat and attaches to an anchoring point Other manufacturers offer the tether strap as an accessory Contact the manufacturer of your child safety seat for information about ordering a tether strap In SuperCabs equipped with Center Facing Jump Seats the tether strap anchor bracket should be installed only at the center of the cab s back panel with the child seat in the front center seating position Installing an anchor bracket at the right rear of the cab may increase risk of injury to an occupant of the right rear center facing jump seat in the event of a collision or a sudden stop If a tether child seat is installed in the right 57 Seating and safety restraints front seating position secure the tether strap to the webbing of the buckled right rear lap belt You can attach a tether strap anchor bracket to the cab inner back panel by using a tether anchor kit 613D74 available at no char
65. in ignition warning chime Sounds when the key is left in the ignition in the OFF LOCK or ACC position and either front door is opened Headlamps on warning chime Sounds when the headlamps or parking lamps are on the ignition is off and the key is not in the ignition and the driver s door is opened STANDARD INSTRUMENT CLUSTER GAUGES SPEED oD CONT OFF THEFT 11 Instrumentation OPTIONAL INSTRUMENT CLUSTER GAUGES Fuel gauge Displays approximately how much fuel is in the fuel tank when the key is in the ON position The fuel gauge may vary slightly when the vehicle is in motion The ignition should be in the OFF position while the vehicle is being refueled When the gauge first indicates empty there is a small amount of reserve fuel in the tank When refueling the vehicle from empty indication the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel The FUEL DOOR icon and arrow indicates which side of the vehicle the fuel filler door is located 12 Instrumentation Engine coolant temperature gauge Indicates the temperature of the engine coolant At normal operating temperature the needle remains within the normal area the area between the H and C If it enters the red section the engine is overheating Stop the vehicle as soon as safely possible switch off the engine immediately and let the eng
66. ine cool Refer to Engine coolant in the Maintenance and care chapter Never remove the coolant recovery cap while the engine is running or hot This gauge indicates the temperature of the engine coolant not the coolant level If the coolant is not at its proper level the gauge indication will not be accurate Tachometer if equipped Indicates the engine speed in revolutions per minute 13 Instrumentation Speedometer Indicates the current vehicle speed Odometer Registers the total kilometers miles of the vehicle Trip odometer Registers the kilometers miles of individual journeys To reset depress the control 14 oo oi f s P ao 90 5 30 foooo00 100 60 20 180 110 MPH km h 120 ooog so 10 120 i s 000000 180 110 MPH km h 120 moo 80 100 oa I 120 a 000000 Instrumentation Engine oil pressure gauge This shows the engine oil pressure in the system Sufficient pressure exists as long as the needle remains in the normal range the area between the H and L H If the gauge indicates low pressure 7 ma stop the vehicle as soon as safely possible and switch off the engine immediately Check the oil level Add oil if needed refer to Checking and adding engine oil in the Maintenance and care XV chapter If the oil level is correct
67. ion Za R A Replacing the tires Replace the tires when the wear band is visible through the tire treads BAMIO 7 7 When replacing full size tires never mix radial bias belted or bias type tires Use only the tire sizes that are listed on the tire pressure decal Make sure that all tires are the same size speed rating and load carrying capacity Use only the tire combinations recommended on the decal If you do not follow these precautions your vehicle may not drive properly and safely l E S Make sure that all replacement tires are of the same size type load carrying capacity and tread design e g All Terrain etc as originally offered by Ford 133 Maintenance and care Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over Tires that are larger or smaller than your vehicle s original tires may also affect the accuracy of your speedometer SNOW TIRES AND CHAINS Driving too fast for conditions creates the possibility of loss of vehicle control Driving at very high speeds for extended periods of time may result in damage to vehicle components Snow tires must be the same size and grade as the tires you currently have on your vehicle The tires on your vehicle have all weather treads to provide traction in rain and snow However in some climates you may need to use snow tires and chains If you need to use s
68. ipment battery needs replacing it may be replaced with a low maintenance battery The low maintenance battery normally does not require additional water during its life of service If the electrolyte level in the battery is low you can add plain tap water to the battery as long as you do not use hard water water with a high alkali content If possible however try to only fill the battery cells with distilled water If the battery needs water often have the charging system checked For longer trouble free operation keep the top of the battery clean and dry Also make certain the battery cables are always tightly fastened to the battery terminals If you see any corrosion on the battery or terminals remove the cables from the terminal s and clean with a wire brush You can neutralize the acid with a solution of baking soda and water Reinstall the cables when you are done cleaning them and apply a small quantity of grease to the top of each battery terminal to help prevent corrosion If your battery has a cover shield make sure it is reinstalled after the battery is replaced Because your vehicle s engine is electronically controlled by a computer some control conditions are maintained by power from the battery When the battery is disconnected or a new battery is installed the engine must relearn its idle conditions before your vehicle will drive properly To begin this process 1 Put the gearshift in P Park au
69. isposal eena ees ONE aT 50 indicator light ee 50 passenger air bag 48 51 52 Air conditioning manual heating and air conditioning system 19 20 21 Ambulance packages 008 3 Anti lock brake system ABS description 0 0 eeeeeeeeeesseeeeees 66 Anti theft system oo 35 Batteiy evaei oersettin anae a 128 voltage gauge eee 15 Brake fluid checking and adding 118 Brakes a aurraren a ects 64 anti lock naseer 64 65 anti lock brake system ABS warning light oeiee 66 fluid checking and adding 118 Brake shift interlock 0 67 Break in period cccceeteeeeeenees 2 Bulbs replacing eee 139 headlamps ceccccseessceeeeeees 140 Specifications nenesinin 141 Changing a tire 0 101 Child safety seats 0 0 54 Chime headlamps ON c ccccesseseeeesseees 11 Cleaning your vehicle 142 engine compartment 143 fADLIC isa verses sea a anii 146 instrument panel 0008 146 plastio Darts seonrusr eee 145 safety belts cccecceeseeees 146 tal lampin ennueg 145 washing ensa nE 142 WAKING oie natania ei uai 143 156 wheels ainoina a 143 WINGOWS pran neasi aa 146 Clutch fluid srinaune n an 119 Controls insana aha 23 31 Driving under special 6X0 41011000 soniiese enanta 77 high water cccceeeseeeereeereees 78 slippery roads 00 0 78 79 Emission control system
70. ition CPP switch Starter Interrupt Relay Anti Theft Cluster 26 10A Battery Saver Relay Electronic Shift Relay Interior Lamp Relay Power Window Relay Electronic Shift Control Module Dome Map Lamp GEM 27 15A Electric Shift Backup Lamps Daytime Running Lamps DRL Transmission Control Switch Generic Electronic Module GEM Radio 97 Roadside emergencies Description Radio Jot Used Jot Used eadlamps Daytime Running Lamps DRL odule Instrument Cluster Jot Used ABS Test Connector Jot Used Power distribution box The power distribution box is located in the engine compartment near the battery The power distribution box contains high current fuses that protect your vehicle s main electrical systems from overloads Maia VONS cS Spe tent Always disconnect the battery before servicing high current fuses Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs 98 Roadside emergencies or AD Panl le 7 O iO i bY oD www ES alm om o m 2 Se vel 5 o am j a K e O jeme fool meg 210 lm y n pal 9 Oi fm woo g Ed SR Be lc ell o m z H Jort lo Hil
71. just been serviced the OBD II system is reset to a not ready for I M test condition To ready the OBD II system for I M testing a minimum of 30 minutes of city and highway driving is necessary as described below e First at least 10 minutes of driving on an expressway or highway e Next at least 20 minutes driving in stop and go city type traffic with at least four idle periods Allow the vehicle to sit for at least eight hours without starting the engine Then start the engine and complete the above driving cycle The engine must warm up to its normal operating temperature Once started do not turn off the engine until the above driving cycle is complete EXTERIOR BULBS Replacing exterior bulbs Check the operation of the following lamps frequently e headlamps e foglamps e high mount brakelamp e brakelamps 139 Maintenance and care e turn signals e license plate lamp e tail lamps e back up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones If a bulb is removed for an extended period of time contaminants may enter the lamp housings and affect lamp performance Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children s reach Grasp the bulb only by its plastic base and do not touch the glass The oil from your hand could cause the bulb to break the next time the headlamps are operated If the bulb is accidentally touched it should
72. k automatic transmission or in 1 First manual transmission The parking brake is not designed to stop a moving vehicle However if the normal brakes fail the parking brake can be used to stop your vehicle in an emergency Since the parking brake applies only the rear brakes the vehicle s stopping distance will be adversely affected Pull the release lever to release the brake Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy TRANSMISSION OPERATION Automatic transmission operation Brake shift interlock This vehicle is equipped with a brake shift interlock feature that prevents the gearshift from being moved from P Park unless the brake pedal is depressed If you cannot move the gearshift out of P Park with the brake pedal depressed 1 Apply the parking brake turn ignition key to LOCK then remove the key 2 Insert the key and turn it to OFF Apply the brake pedal and shift to N Neutral 3 Start the vehicle If it is necessary to use the above procedure to move the gearshift it is possible that a fuse has blown Refer to Fuses and relays in the Roadside emergencies chapter 67 Driving Do not drive your vehicle until you verify that the brakelamps are working If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears in a steady pattern Press lightly on the accelerator in each gear Do no
73. l still retract to remove any slack in the shoulder belt The automatic locking mode is not available on the driver safety belt When to use the automatic locking mode e When a tight lap shoulder fit is desired e Anytime a child safety seat is installed in the vehicle Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter How to use the automatic locking mode e Buckle the combination lap and shoulder belt 41 Seating and safety restraints e Grasp the shoulder portion and pull downward until the entire belt is extracted e Allow the belt to retract As the belt retracts you will hear a clicking sound This indicates the safety belt is now in the automatic locking mode How to disengage the automatic locking mode Disconnect the combination lap shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive emergency locking mode Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder e Regular Cab 42 Seating and safety restraints e 2 door SuperCab e 4 door SuperCab To lower the shoulder belt height push the button and slide the height control down To raise the height of the shoulder belt slide the height adjuster up Pull
74. ld seat is used in the right front or center front passenger seat position Refer to Passenger OFF air bag deactivate switch in the Seating and safety restraints chapter PASSENGER AIRBAG 23 Controls and features AUDIO SYSTEM Refer to the Audio Guide in your owner portfolio TURN SIGNAL CONTROL e Push down to activate the left turn signal e Push up to activate the right turn signal SPEED CONTROL IF EQUIPPED To turn speed control on e Press ON Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km h 80 mph Do not use the speed control in heavy traffic or on roads that are winding slippery or unpaved Do not shift the gearshift lever into N Neutral with the speed control on 24 Controls and features To turn speed control off e Press OFF or e Turn off the vehicle ignition gt Once speed control is switched off the previously programmed set speed will be erased To set a speed e Press SET ACC SET ACCEL For speed control to operate the speed control must be ON and the vehicle speed must be greater than 48 km h 80 mph If you drive up or down a steep hill your vehicle speed may vary momentarily slower or faster than the set speed This is normal Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill If your vehicle speed is faster than the set speed while driving on
75. le Under normal conditions your vehicle s climate control system should be left in any position other than MAX A C or OFF when the vehicle is parked This allows the vehicle to breathe through the outside air inlet duct e MAX A C Uses recirculated air to cool the vehicle MAX A C is noisier than A C but more economical and will cool the inside of the vehicle faster Airflow will be from the instrument panel registers This mode can also be used to prevent undesirable odors from entering the vehicle e A C Uses outside air to cool the vehicle It is quieter than MAX A C but not as economical Airflow will be from the instrument panel registers 7s Vent Distributes outside air through the instrument panel registers However the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode e OFF Outside air is shut out and the fan will not operate For short periods of time only use this mode to prevent undesirable odors from entering the vehicle e Panel and floor Distributes outside air through the instrument panel registers and the floor ducts Heating and air conditioning capabilities are provided in this mode For added customer comfort when the temperature control knob is anywhere in between the full hot and full cold positions the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers 20 Controls
76. le to tow the vehicle with the front wheels on the ground and the rear wheels off the ground On 4x4 vehicles it is recommended that your vehicle be towed with a wheel lift or flatbed equipment Do not tow with slingbelt equipment Ford Motor Company has not developed or approved a slingbelt towing procedure When calling for a tow truck tell the operator what kind of vehicle you have A towing manual is available from Ford Motor Company for all authorized tow truck operators Have your tow truck driver refer to this manual for proper hook up and towing procedures for your vehicle 109 Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle e We highlight do it yourself items in the engine compartment for easy location e We provide a Service Guide which makes tracking routine service easy If your vehicle requires professional service your dealership can provide necessary parts and service Check your Warranty Guide to find out which parts and services are covered Use only recommended fuels lubricants fluids and service parts conforming to specifications Motorcraft parts are designed and built to provide the best performance in your vehicle PRECAUTIONS WHEN SERVICING YOUR VEHICLE Be especially careful when inspecting or servicing your vehicle e Do not work on a hot engine e When the engine is running make sure that loose clothing jewelry or long hair does not get caught up in
77. lock unlock press any button on all transmitters Cup to four When completed switch the ignition to OFF All transmitters must be reprogrammed at the same time Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door s or sound the personal alarm The system automatically turns off after 25 seconds or when the ignition is turned to the START or ACC position The dome lamp switch Gf equipped must not be set to the OFF position for the illuminated entry system to operate The inside lights will not turn off if e they have been turned on with the dimmer control or e any door is open The battery saver will shut off the interior lamps 40 minutes after the ignition has been turned to the OFF position 34 Controls and features PERIMETER ALARM SYSTEM Arming the system When armed this system will help protect your vehicle from unauthorized entry When unauthorized entry occurs the system will flash the parking lamps and the theft indicator lamp and chirp the horn The system is ready to arm whenever the ignition is turned OFF Any of the following actions will prearm the alarm system e Press the remote entry lock control e Open a door and press the power door lock control to lock the doors If a door is open the system is prearmed and is waiting for the door to close The theft indicator in the instrument panel will be lit continuously when the system is prearmed
78. ly installing and securely tightening the gas cap After three driving cycles without these or any other temporary malfunctions present the Check Engine light should turn off A driving cycle consists of a cold engine startup followed by mixed city highway driving No additional vehicle service is required If the Check Engine light remains on have your vehicle serviced at the first available opportunity Light is blinking Engine misfire is occurring which could damage your catalytic converter You should drive in a moderate fashion avoid heavy acceleration and deceleration and have your vehicle serviced at the first available opportunity Under engine misfire conditions excessive exhaust temperatures could damage the catalytic converter the fuel system interior floor coverings or other vehicle components possibly causing a fire Instrumentation Fuel reset if equipped Illuminates when the ignition key is turned to the ON position and the FUEL fuel pump shut off switch has been triggered For more information RESET refer to Fuel pump shut off switch in the Roadside emergencies chapter Air bag readiness Momentarily illuminates when the O O ignition is turned ON If the light 7 fails to illuminate continues to flash PV or remains on have the system serviced immediately Safety belt Momentarily illuminates when the ignition is turned to the ON position P to remind you to fasten your safety belts For mor
79. mmediately Cleaning the wheels Wash with the same detergent as the body of your vehicle Do not use acid based or alcohol based wheel cleaners steel wool fuel or strong detergents Never use abrasives that will damage the finish of special wheel surfaces Use a tar remover to remove grease and tar Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal When washing e Take care when using a power washer to clean the engine The high pressure fluid could penetrate the sealed parts and cause damage e Do not spray with cold water to avoid cracking the engine block or other engine components e Cover the highlighted areas to prevent water damage when cleaning the engine 143 Maintenance and care AS PANI pei j A PAN RN ees aS A A Sia SA OE CUREA OAKS BOO Ss No 2 144 Maintenance and care 5 PAV A NEA YA VAT YA e 2 5L e Never wash or rinse the engine while it is running water in the running engine may cause internal damage Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning Clean with a tar remover if necessary Do not clean plastic parts with thinners solvents or petroleum based cleaners Cleaning the exterior lamps Wash with the same detergent
80. modes with a temporary spare If 4WD operation is necessary do not operate above speeds of 16 km h 10 mph or for distances above 80 km 50 miles If you use the temporary spare tire continuously or do not follow these precautions the tire could fail causing you to lose control of the vehicle possibly injuring yourself or others When driving with the temporary spare tire do not e exceed 80 km h 50 mph under any circumstances e load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label e tow a trailer e use tire chains e drive through an automatic car wash because of the vehicle s reduced ground clearance e try to repair the temporary spare tire or remove it from its wheel e use the wheel for any other type of vehicle Conventional spare tire information If you have the conventional spare tire you can use it as a spare or a regular tire The spare is identical to the other tires on your vehicle although the wheel may not match 101 Roadside emergencies Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations Under the vehicle just forward of the rear bumper Jack jack Regular Cab behind seats and underneath the jack handle wheel and tools cover nut wrench SuperCab stowed in the passenger side rear cab compartment or behind the jump seat in a separate tool bag Four door models stowed behind the front se
81. moving parts e Do not work on a vehicle with the engine running in an enclosed space unless you are sure you have enough ventilation Keep all lit cigarettes open flames and other lit material away from the battery and all fuel related parts If you disconnect the battery the engine must relearn its idle conditions before your vehicle will drive properly as explained in Battery in this chapter Working with the engine off e Automatic transmission 1 Set the parking brake and ensure the gearshift is securely latched in P Park 2 Turn off the engine and remove the key 3 Block the wheels to prevent the vehicle from moving unexpectedly e Manual transmission 1 Set the parking brake 2 Depress the clutch and place the gearshift in 1 First 110 Maintenance and care 3 Turn off the engine and remove the key 4 Block the wheels to prevent the vehicle from moving unexpectedly Working with the engine on e Automatic transmission 1 Set the parking brake and ensure the gearshift is securely latched in P Park 2 Block the wheels to prevent the vehicle from moving unexpectedly Do not start your engine with the air cleaner removed and do not remove it while the engine is running e Manual transmission 1 Set the parking brake depress the clutch and place the gearshift in N Neutral 2 Block the wheels to prevent the vehicle from moving unexpectedly Do not start your engine with the air clea
82. n the transmission does not shift into OFF overdrive If the light does not come on when the transmission control switch is depressed or if the light flashes when you are driving have your vehicle serviced Instrumentation Check gage if equipped Illuminates when the key is in the ON position and the engine coolant CHECK temperature is high the engine oil GAGE pressure is low or the fuel level is near empty Refer to Engine coolant temperature gauge Engine oil pressure gauge or Fuel gauge in this chapter for more information Four wheel drive low if equipped Illuminates when four wheel drive low is engaged 4 W D LOW Four wheel drive high if equipped Illuminates when four wheel drive high is engaged 4 W D HIGH Door ajar Illuminates when the ignition is in the ON or START position and any DOOR door is open AJ AR Speed control if equipped This light comes on when either the SET ACCEL or RESUME controls SPEED are pressed It turns off when the CONT speed control OFF control is pressed the brake is applied or the ignition is turned to the OFF position 10 Instrumentation Safety belt warning chime Chimes to remind you to fasten your safety belts For information on the safety belt warning chime refer to the Seating and safety restraints chapter Supplemental restraint system SRS warning chime For information on the SRS warning chime refer to the Seating and safety restraints chapter Key
83. n this chapter for more instructions If you smell exhaust fumes inside your vehicle have your dealer inspect your vehicle immediately Do not drive if you smell exhaust fumes Important safety precautions A computer system controls the engine s idle revolutions per minute RPM When the engine starts the idle RPM runs faster to warm the engine If the engine idle speed does not slow down automatically have the vehicle checked Do not allow the vehicle to idle for more than ten minutes Before starting the vehicle 1 Make sure all vehicle occupants have buckled their safety belts For more information on safety belts and their proper usage refer to the Seating and safety restraints chapter 59 Starting 2 Make sure the headlamps and vehicle accessories are off If starting a vehicle with an automatic transmission e Make sure the parking brake is set e Make sure the gearshift is in P Park If starting a vehicle with a manual transmission e Make sure the parking brake is set e Push the clutch pedal to the floor 3 Turn the key to 4 ON without turning the key to 5 START 60 Starting 4 SPEED O D CONT OFF EM GT Make sure the corresponding lights illuminate briefly If a light fails to iluminate have the vehicle serviced e If the driver s safety belt is fastened the light A will not illumin
84. n when the brakes are firmly applied The accompanying illustration depicts the advantage of an ABS equipped vehicle on bottom to a non ABS equipped vehicle on top during hard braking 65 Driving ABS warning lamp The s warning lamp in the instrument cluster illuminates for about five seconds when starting the vehicle If an ABS fault is detected the light will remain on and your vehicle should be serviced as soon as possible Normal braking is still effective unless the BRAKE warning lamp is O also illuminated BRAKE Using ABS e In an emergency or when maximum efficiency from the ABS is required apply continuous full force on the brake The ABS will be activated immediately thus allowing you to retain full steering control of your vehicle and providing there is sufficient space will enable you to avoid obstacles and bring the vehicle to a controlled stop e We recommend that you familiarize yourself with this braking technique However avoid taking any unnecessary risks Parking brake Apply the parking brake whenever the vehicle is parked To set the parking brake press the parking brake pedal down until the pedal stops The BRAKE warning lamp in the instrument cluster illuminates and O remains illuminated when the BRAKE ignition is turned ON until the parking brake is released 66 Driving Always set the parking brake fully and make sure that the gearshift is securely latched in P Par
85. ner removed and do not remove it while the engine is running OPENING THE HOOD 1 Inside the vehicle pull the hood release handle located under the bottom of the instrument panel 2 Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood 3 Lift the hood and support it with the prop rod Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2 5L 14 engine 1 2 3 4 oat N AN MT eo WF N y A S UB ACSA E KA X 10 9 8 1 Engine coolant reservoir 2 Windshield washer fluid reservoir 3 Transmission fluid dipstick automatic transmission 4 Engine oil dipstick 5 Brake fluid reservoir 6 Clutch fluid reservoir manual transmission 7 Battery 8 Power steering fluid reservoir 9 Engine oil filler cap 10 Air filter assembly 112 Maintenance and care 3 0L V6 Vulcan engine San aan Wee Pa URC AE NI I rOn oe SALN i a 1 Engine coolant reservoir 2 Windshield washer fluid reservoir 3 Engine oil filler cap 4 Transmission fluid dipstick automatic transmission 5 Engine oil dipstick 6 Brake fluid reservoir 7 Clutch fluid reservoir 8 Battery 9 Power steering fluid reservoir 10 Air filter assembly 113 Maintenance and care 4 0L V6 engine
86. nflate in a collision If the passenger air bag switch is turned off it increases the likelihood of injury to forward facing occupants in the passenger seat Turning the passenger air bag off 1 Insert the ignition key turn the switch to OFF and remove the key ON 2 When the ignition is turned to the SD ON position the OFF light illuminates briefly momentarily OFF shuts off and then turns back on This indicates that the passenger air PASSENGER AIRBAG bag is deactivated If the light fails to illuminate when the passenger air bag switch is in the OFF position and the ignition switch is in ON have the passenger air bag switch serviced at your Ford or Lincoln Mercury dealer immediately In order to avoid inadvertent deployment of the passenger air bag always remove the ignition key from the passenger air bag deactivate switch 51 Seating and safety restraints Turning the passenger air bag back on The passenger air bag remains OFF until you turn it back ON 1 Insert the ignition key and turn the switch to ON ON 2 The OFF light will briefly Ker illuminate when the ignition is turned to On This indicates that the OFF passenger air bag is operational PASSENGER AIRBAG If the light is illuminated when the passenger air bag switch is in the ON position and the ignition switch is in ON have the passenger air bag switch serviced at your Ford or Lincoln Mercury dealer immediately
87. ng the wipers easy turn the ignition to ACC then turn the wipers on When the wipers reach the vertical position turn the ignition to LOCK 129 Maintenance and care To replace the wiper blades 1 Pull the wiper arm away from the windshield and lock into the service position 2 Turn the blade at an angle from the wiper arm Push the lock pin with a screwdriver to release the blade and pull the wiper blade down toward the windshield to remove it from the arm 3 Attach the new wiper to the wiper arm and press it into place until a click is heard v v INFORMATION ABOUT TIRE QUALITY GRADES New vehicles are fitted with tires that have their Tire Quality Grade described below molded into the EELO tire s sidewall These Tire Quality Q P Grades are determined by standards Re r that the United States Department See of Transportation has set T lt Tire Quality Grades apply to new ree a pneumatic tires for use on passenger cars They do not apply to deep tread winter type snow tires space saver or temporary use spare tires tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575 104 c 2 U S Department of Transportation Tire quality grades The U S Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it 130 Maintenance
88. now tires and chains you must install steel wheels of the same size and specifications as those originally installed Follow these guidelines when using snow tires and chains Do not use tire chains on aluminum wheels Chains may chip the wheels Use only SAE Class S chains Install chains securely verifying that the chains do not touch any wiring brake lines or fuel lines Drive cautiously If you hear the chains rub or bang against your vehicle stop and re tighten the chains If this does not work remove the chains to prevent damage to your vehicle If possible avoid fully loading your vehicle Remove the tire chains when they are no longer needed Do not use tire chains on dry roads The suspension insulation and bumpers will help prevent vehicle damage Do not remove these components from your vehicle when using snow tires and chains 134 Maintenance and care WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire If you do not use the proper fuel cap the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision The fuel system may be under pressure If the fuel cap is venting vapor or if you hear a hissing sound wait until it stops before completely removing the cap Automotive fuels can cause serious injury or death if misused or
89. nto place to lock the steering wheel in position A Never adjust the steering wheel when the vehicle is moving HAZARD FLASHER For information on the hazard flasher control refer to Hazard lights control in the Roadside emergencies chapter WINDSHIELD WIPER WASHER CONTROLS Rotate the windshield wiper control to the desired interval low or high speed position The bars of varying length are for intermittent wipers When in this position rotate the control upward for fast intervals and downward for slow intervals Push the control on the end of the stalk to activate washer Push and hold for a longer wash cycle 29 Controls and features POWER WINDOWS IF EQUIPPED Press and hold the rocker switches to open and close windows e Press the top portion of the I rocker switch to close e Press the bottom portion of the rocker switch to open One touch down e Press AUTO completely down and release quickly The window will open fully Depress again to stop window operation 30 Controls and features POWER DOOR LOCKS IF EQUIPPED Press the top of the control to UNLOCK unlock all doors and the bottom to lock all doors POWER SIDE VIEW MIRRORS IF EQUIPPED To adjust your mirrors 1 Select Ei to adjust the left mirror or P to adjust the right mirror 2 Move the control in the direction you wish to tilt the mirror 3 Return to the center position to lock mirrors in place CENTER C
90. o the negative terminal of the booster battery 3 and the other end to a metal part of the engine to be started 4 not to the negative terminal of the discharged battery 5 Make sure that the jump leads are clear of moving parts of the engine Do not connect the end of the second cable to the negative terminal of the battery to be jumped A spark may cause an explosion of the gases that surround the battery Jump starting 1 Start the booster vehicle and run the engine at moderately increased speed 2 Start the engine of the vehicle with the discharged battery 3 Once the engine has been started run both vehicles for a further three minutes before disconnecting the leads 107 Roadside emergencies Removing the jumper cables 1 Remove the jumper cables in reverse order Take the cable off the metallic surface 1 first followed by the cable on the negative booster battery terminal 2 2 Remove the cable from the positive terminal of the booster battery 8 and then the discharged battery 4 3 After the disabled vehicle has been started allow it to idle for a while so the engine can relearn its idle conditions 108 Roadside emergencies WRECKER TOWING If you need to have your vehicle towed contact a professional towing service or if you are a member your roadside assistance center On 4x2 vehicles it is acceptab
91. oir For more information on engine coolant maintenance refer to Adding engine coolant in this chapter Automotive fluids are not interchangeable do not use engine coolant antifreeze or windshield washer fluid outside of its specified function and vehicle location Adding engine coolant Do not put engine coolant in the container for the windshield washer fluid If sprayed on the windshield engine coolant could make it difficult to see through the windshield When the engine is cool add a 50 50 mixture of engine coolant and water to the engine coolant recovery reservoir DO NOT ADD DIRECTLY TO THE RADIATOR Add straight water only in an emergency but you should replace it with a 50 50 mixture of coolant and distilled water as soon as possible Maintenance and care Check the coolant level in the coolant recovery reservoir the next few times you drive the vehicle If necessary add enough of a 50 50 mixture of coolant and water to bring the liquid level to the fill line on the reservoir Never remove the coolant recovery cap while the engine is running or hot If you must remove the coolant recovery cap follow these steps to avoid personal injury 1 Before you remove the cap turn the engine off and let it cool 2 When the engine is cool wrap a thick cloth around the cap Slowly turn cap counterclockwise until pressure begins to release 3 Step back while the pressure releases 4 When you are sure that all the pres
92. on station for trucks 4 Subtract your loaded vehicle weight from the maximum GCWR on the following charts This is the maximum trailer weight your vehicle can tow and must fall below the maximum shown under maximum trailer weight on the chart DRIVING THROUGH WATER Do not drive quickly through standing water especially if the depth is unknown Traction or brake capability may be limited and if the ignition system gets wet your engine may stall Water may also enter your engine s air intake and severely damage your engine If driving through deep or standing water is unavoidable proceed very slowly Never drive through water that is higher than the bottom of the hubs truck wheel rims car Once through the water always try the brakes Wet brakes do not stop the vehicle as effectively as dry brakes Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal TRAILER TOWING Your vehicle may tow a class I II or III trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your engine and rear axle ratio on the following charts Your vehicle s load capacity is designated by weight not by volume so you cannot necessarily use all available space when loading a vehicle Towing a trailer places an additional load on your vehicle s engine transmission axle brakes tires and suspension Inspect these components carefully after any to
93. or each engine transmission combination any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle Maximum Trailer Weight maximum weight of a trailer the loaded vehicle including passengers and cargo is permitted to tow It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle Trailer Weight Range Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating Remember to figure in the tongue load of your loaded trailer when figuring the total weight Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label Do not use replacement tires with lower weight capacities than the originals because they may lower the vehicle s GVWR and GAWR limitations Replacement tires with a higher weight limit than the originals do not increase the GVWR and GAWR limitations 80 Driving Calculating the load your vehicle can carry tow 1 Use the Safety Compliance Certification Label to find the axle code number and engine type for your vehicle 2 Use the appropriate maximum gross combined weight rating GCWR chart to find the maximum GCWR for your type engine and rear axle ratio 3 Weigh your vehicle as you customarily operate the vehicle without cargo To obtain correct weights try taking your vehicle to a shipping company or an inspecti
94. ox bed until it can be repaired Tire change procedure 1 Park on a level surface activate hazard flashers and place gearshift lever in P Park automatic transmission or 1 First manual transmission 2 Set the parking brake 103 Roadside emergencies 3 Block the diagonally opposite wheel 4 Insert tapered end of the lug wrench behind hub caps and twist them off 5 Loosen each wheel lug nut one half turn counterclockwise but do not remove them until the wheel is raised off the ground 6 Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm 1 inch off the ground e Front 104 Roadside emergencies e Rear e Never use the differential as a jacking point 7 Remove the wheel lug nuts with the lug wrench 8 Replace the flat tire with the spare tire making sure the valve stem is facing outward Reinstall the lug nuts until the wheel is snug against the hub Do not fully tighten the lug nuts until the wheel has been lowered 9 Lower the wheel by turning the jack handle counterclockwise 10 Remove the jack and fully tighten the lug nuts in the order shown 11 Stow the flat tire Refer to Stowing the spare 12 Stow the jack and lug wrench Make sure the jack is fastened so it does not rattle when you drive 13 Unblock the wheels 105 Roadside emergencies JUMP STARTING YOUR V
95. panel during headlamp 4 and parklamp operation e Rotate up to brighten e Rotate down to dim oS DIM CLIMATE CONTROL SYSTEM Heater only system if equipped amp RR OFF ap w Fan speed control Controls the volume of air circulated se in the vehicle C A lt 17 Controls and features Temperature control knob Controls the temperature of the airflow inside the vehicle On heater only systems the air cannot EF be cooled below the outside temperature Mode selector control Controls the direction of the airflow Si oF wed gp e to the inside of the vehicle a D e 74 Vent Distributes outside air through the instrument panel registers e 7 Panel and floor Distributes outside air through the instrument panel registers and the floor ducts e OFF Outside air is shut out and the fan will not operate e Floor Allows for maximum heating Distributes outside air through the floor ducts e Floor and defrost Distributes outside air through the floor ducts and the windshield defroster ducts e 7 Distributes outside air through the windshield defroster ducts It can be used to clear ice or fog from the windshield Operating tips e In humid weather select Y before driving This will help to prevent your windshield from fogging After a few minutes select any desired position e To prevent humidity buildup inside the vehicle don t drive with the climate control system
96. protection and long life If a replacement oil filter is used that does not meet Ford material and design specifications startup engine noises or knock may be experienced It is recommended you use the appropriate Motorcraft oil filter or another brand meeting Ford specifications for your engine application 117 Maintenance and care Changing the engine oil and filter Change your engine oil and filter according to the appropriate schedule listed in the Service Guide Ford production and aftermarket Motorcraft oil filters are designed for added engine protection and long life If a replacement oil filter is used that does not meet Ford material and design specifications startup engine noises or knock may be experienced It is recommended you use the appropriate Motorcraft oil filter or another brand meeting Ford specifications for your engine application BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed at least once each year 1 Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir 2 Visually inspect the fluid level 3 If necessary add brake fluid until the level reaches MAX Do not fill above this line 4 Use only a DOT 3 brake fluid certified to meet Ford specifications Refer to Lubricant specifications in the Capacities and specifications chapter 118 Maintenance and care A Brake fluid is toxic Q If
97. r leaves from the air intake area at the bottom of the windshield under the hood e If your vehicle has been parked with the windows closed during hot weather the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open This will force most of the hot stale air out of the vehicle Then operate your air conditioner as you would normally 21 Controls and features e When placing objects on top of your instrument panel be careful to not place them over the defroster outlets These objects can block airflow and reduce your ability to see through your windshield Also avoid placing small objects on top of your instrument panel These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system 4WD CONTROL IF EQUIPPED This control operates the 4WD it Refer to the Driving chapter for wp GH H more information e 22 Controls and features AUXILIARY POWER POINT Ows as rea The auxiliary power point is located on the instrument panel This outlet should be used in place of the cigarette lighter for optional electrical accessories PASSENGER AIR BAG DEACTIVATE SWITCH This switch must be used to deactivate the passenger air bag ON O whenever a chi
98. r to the Atir bag readiness section in the Instrumentation chapter or Passenger air bag deactivate switch section in this chapter Routine maintenance of the air bag is not required A difficulty with the system is indicated by one or more of the following e The readiness lights will either O O flash or stay lit oe e The readiness lights will not ZN illuminate immediately after ignition is turned on e A series of five beeps will be heard The tone pattern will repeat periodically until the problem and light are repaired If any of these things happen even intermittently have the SRS serviced at your dealership or by a qualified technician immediately Unless serviced the system may not function properly in the event of a collision Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles see your local dealership or qualified technician Air bags MUST BE disposed of by qualified personnel 50 Seating and safety restraints Passenger air bag deactivate switch Your vehicle has a passenger air bag deactivate switch This switch MUST be used to activate or deactivate the passenger air bag whenever a child seat is used in the right front or center front passenger seat position PASSENGER AIRBAG Keep the passenger air bag turned on unless there is a child seat installed in the front seat When the passenger air bag switch is turned off the passenger air bag will not i
99. reviously programmed set speed Controls and features 27 Controls and features To return to a previously set speed e Press RES RSM RESUME For RES RSM RESUME to operate the vehicle speed must be faster than 48 km h 80 mph Indicator light if equipped This light comes on when either the SET ACC SET ACCEL or SPEED RES RSM RESUME controls are CONT pressed It turns off when the speed control OFF control is pressed the brake is applied or the ignition is turned to the OFF position OVERDRIVE CONTROL Activating overdrive Overdrive is the normal drive position for the best fuel economy The overdrive function allows automatic upshifts to second third and fourth gear o D 0 D When you shut off and re start your vehicle the transmission will automatically return to normal Overdrive mode Deactivating overdrive Press the Transmission Control Switch TCS located on the end of the gearshift lever The Transmission Control Indicator Light TCIL will illuminate on the instrument cluster The transmission will operate in gears one through three To return to normal overdrive mode press the Transmission Control Switch again The TCIL will no longer be illuminated 28 Controls and features TILT STEERING IF EQUIPPED Push the steering control away from you to move the steering wheel up or down Tip the steering wheel to the desired position then pull the control back i
100. rged in water the rear axle lubricant should be changed Axle lubricant quantities are not to be checked unless a leak is suspected Recreational towing all wheels on the ground Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground such as behind a recreational vehicle These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication 89 Driving 2WD automatic transmissions e Release the parking brake and place the transmission in N Neutral e Maximum speed is 56 km h 85 mph e Maximum distance is 80 km 50 miles If a distance of 80 km 50 miles or a speed of 56 km h 85 mph must be exceeded you must disconnect the driveshaft Mark the driveshaft and axle flanges to ensure proper position when reconnecting the driveshaft Refer to the Workshop Manual for proper fastener torque specifications When disconnecting installing the driveshaft the parking brake must be set and the wheels blocked to ensure the vehicle does not roll With the driveshaft disconnected the maximum speed is 88 km h 55 mph and there are no mileage restrictions See your dealer for help with disconnecting the driveshaft 2WD manual transmissions e Release the parking brake and place the transmission in the neutral position e Maximum speed is 56 km h 85 mph e Maximum distance is limited by towing equipment manu
101. s polishes and waxes Washing your vehicle Wash your vehicle regularly with cold or lukewarm water Never use strong detergents or soap If your vehicle is particularly dirty use a quality car wash detergent Always use a clean sponge washing glove or similar device and plenty of water for best results To avoid spots avoid washing when the hood is still warm immediately after or during exposure to strong sunlight 142 Maintenance and care During winter months it is especially important to wash the vehicle on a regular basis Large quantities of dirt and road salt are difficult to remove and also cause damage to the vehicle Remove any exterior accessories such as antennas before entering a car wash After washing apply the brakes several times to dry them Waxing your vehicle Wax when water stops beading on the surface This could be every three or four months depending on operating conditions Use only carnauba or synthetic based waxes Use cleaning fluid or alcohol with a clean cloth to remove any bugs and tar before waxing vehicle Use tar remover to remove any tar spots Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch up paint repair foil or aerosol paint spray from the Ford accessory line Observe the application instructions on the products Remove particles such as bird droppings tree sap insect remains tar spots road salt and industrial fallout i
102. s more than 16 km h 10 mph the speed control will cancel automatically Resume speed with accelerator pedal 78 Driving If speed control cancels after climbing the hill reset speed by pressing and holding the SET ACCEL button to resume speeds over 50 km h 30 mph Automatic transmissions may shift frequently while driving up steep grades Eliminate frequent shifting by shifting out of Overdrive into D Drive Driving on snow and ice A 4WD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle Avoid sudden applications of power and quick changes of direction on snow and ice Apply the accelerator slowly and steadily when starting from a full stop When braking apply the brakes as you normally would In order to allow the anti lock brake system ABS to operate properly keep steady pressure on the brake pedal Allow more stopping distance and drive slower than usual Consider using one of the lower gears TRACTION LOK AXLE IF EQUIPPED This axle provides added traction on slippery surfaces particularly when one wheel is on a poor traction surface Under normal conditions the Traction Lok axle functions like a standard rear axle Extended use of other than the manufacturer s specified size tires on a Traction Lok rear axle could result in a permanent reduction in effectiveness This loss of effectiveness does not affect normal driving and should not be noticeable to the dri
103. se I softness REAR SEATS Center facing jump seat 2 door SuperCab if equipped To open pull inboard and down on the seat handle To stow the seat pull seat bottom back to the fully upright position A Do not install a child seat in a center facing jump seat 38 Seating and safety restraints Center facing jump seat 4 door SuperCab if equipped To open lift handle and pull seat assembly down then raise seatback To stow the seat fold seat back down and raise seat assembly to the fully upright position Do not install a child seat in a center facing jump seat SAFETY RESTRAINTS Safety restraints precautions A Always drive and ride with your seatback upright and the lap belt snug and low across the hips Q To prevent the risk of injury make sure children sit where they can be properly restrained A Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision All occupants of the vehicle including the driver should always wear their safety belts It is extremely dangerous to ride in a cargo area inside or outside of a vehicle In a collision people riding in these areas are more likely to be seriously injured or killed Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts Be sure everyone in your vehicle is in a seat and using a saf
104. ssengers and cargo and the loaded trailer must not exceed the Gross Combined Weight Rating GCWR Trailer towing table 4x2 automatic transmission Maximum Maximum trailer Maximum frontal GCWR kg weight kg lbs area of trailer m lbs 0 maximum ft Regular Cab 4x2 2 5L 4 10 2 494 5 500 0 1 007 2 220 Equal to frontal area of base vehicle 84 Driving Trailer towing table 4x2 automatic transmission Regular Cab 4x2 Splash or Special Suspension area of base vehicle area of base vehicle area of base vehicle 3 55 0 907 0 2 000 Equal to frontal area of base vehicle 3 0L 4 64 50 4 64 50 4 4 64 50 SuperCab 4x2 Splash or Special Suspension area of base vehicle area of base vehicle area of base vehicle Optional payload is not available on 4x2 Splash or Special Suspension therefore maximum trailer weight is 907 kg 2 000 Ibs For high altitude operation reduce GCW by 2 per 300 meters 1 000 ft elevation in this chapter vehicle see Calculating the load earlier in this chapter Maximum trailer weight is shown The combined weight of the completed towing vehicle including hitch passengers and cargo and the loaded trailer must not exceed the Gross Combined Weight Rating GCWR 4 H ee 0 4 0 3 0L 85 Driving Trailer tow table 4x4 automatic transmission Maximum Maximum trailer frontal area of weight kg lbs trailer
105. ssion control indicator light TCIL will illuminate on the O D instrument cluster OF F Drive Not shown on the display Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the position The TCIL will illuminate on the instrument cluster Transmission operates in gears one through three Drive provides more engine braking than Overdrive and is useful when e driving with a heavy load e towing a trailer up or down steep hills e additional engine braking is desired If towing a trailer refer to Driving while you tow in the Towing a trailer chapter To return to Overdrive mode press the transmission control switch The TCIL will no longer be illuminated Each time the vehicle is started the transmission will automatically return to normal overdrive mode Every time the vehicle is shut off and restarted you must press the transmission control switch to cancel overdrive operation if driving in overdrive is not desired 69 Driving 2 Second Use 2 Second to start up on slippery roads or to provide P RN D A downgrades 1 First Use 1 Low to provide maximum engine braking on steep downgrades Upshifts can be made by shifting to 2 Second or to Overdrive Selecting 1 Low P RNO21 Coo at higher speeds causes the transmission to shift to a lower gear and will shift to 1 Low after vehicle decelerates to the proper speed
106. ster Transmission operates in gears one through four Drive provides more engine braking than Overdrive and is useful whenever driving conditions i e city traffic_hilly terrain etc cause the transmission to excessively shift between Overdrive and Drive Also deactivate Overdrive when e driving with a heavy load e towing a trailer up or down steep hills e additional engine braking is desired To return to Overdrive mode press the transmission control switch The TCIL will no longer be illuminated Each time the vehicle is started the transmission will automatically return to normal overdrive mode 71 Driving 2 Second Use 2 Second to start up on slippery roads or to provide additional engine braking on downgrades Transmission operates in third gear 1 First Use 1 First to provide maximum engine braking on steep downgrades Upshifts can be made by shifting to 2 Second or to Overdrive Selecting 1 Low at higher speeds causes the transmission to shift to a lower gear and will shift to 1 First after the vehicle decelerates to the proper vehicle speed Driving a manual transmission if equipped Using the clutch Vehicles equipped with a manual transmission have a starter interlock N J that prevents cranking the engine unless the clutch pedal is fully depressed When starting a vehicle with a manual transmission 1 Hold down the brake pedal 2 Depress the cl
107. sure has been released use the cloth to turn it counterclockwise and remove the cap Use Ford Premium Cooling System Fluid E2FZ 19549 AA in Canada Motorcraft CXC 8 B or an equivalent premium engine coolant that meets Ford specification ESE M97B44 A Ford Premium Engine Coolant is an optimized formula that will protect all metals and rubber elastomers used in Ford cooling systems for four years or 80 000 km 50 000 miles Do not use alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze Do not use supplemental coolant additives in your vehicle These additives may harm your engine cooling system The use of an improper coolant may void your warranty of your vehicle s engine cooling system Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln Mercury dealers use recycled engine coolant produced by Ford approved processes Not all coolant recycling processes produce coolant which meets Ford specification ESE M97B44 A and use of such coolant may harm engine and cooling system components Always dispose of used automotive fluids in a responsible manner Follow your community s regulations and standards for recycling and disposing of automotive fluids 122 Maintenance and care Coolant refill capacity To find out how much fluid your vehicle s cooling system can hold refer to Refill capacities in the Capacities and specifications chapter Have your dealer
108. t rock the vehicle for more than a few minutes The transmission and tires may be damaged or the engine may overheat Always set the parking brake fully and make sure the gearshift is latched in P Park Turn off the ignition whenever you leave your vehicle Driving with a 4 speed automatic transmission 2 5L and 3 0L engines only Understanding gearshift positions Pull the gearshift lever towards you and downward to move the automatic gearshift Hold the brake pedal down while you move the gearshift lever from position to position If you do not hold the brake pedal down your vehicle may move unexpectedly and injure someone P Park Always come to a complete stop before shifting into P Park Make sure the gearshift is securely latched ha See in P Park R Reverse With the gearshift in R Reverse the vehicle will move backward P R N D 2 1 Re ay Ses R RNO21 I Always come to a complete stop before shifting into and out of R Reverse 68 Driving N Neutral With the gearshift in N Neutral the vehicle can be started and is free to roll Hold the brake pedal down while in this gear Overdrive The normal driving position for the best fuel economy Transmission P RN P 21 ee eee operates in gears one through four Overdrive can be deactivated by pressing the transmission control d switch on the end of the gearshift ON OFF _ lever The transmi
109. ted gasoline is not available when you refuel your vehicle can be operated on non California fuels However even though your engine will perform adequately on other gasolines the performance of the emission control devices and systems may be adversely affected Repair of damage caused by using a fuel for which your vehicle was not designed may not be covered by your warranty Octane recommendations Your vehicle is designed to use Regular unleaded with an R M 2 2 octane rating of 87 We do not 87 recommend gasolines labeled as Regular that are sold with octane ratings of 86 or lower in high altitude areas Do not be concerned if your engine sometimes knocks lightly However if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating see your dealer or a qualified service technician to prevent any engine damage Fuel quality If you are experiencing starting rough idle or hesitation driveability problems during a cold start try a different brand of Regular gasoline Premium gasoline is not recommended particularly in the United States because it may cause these problems to become more pronounced If the problems persist see your dealer or a qualified service technician 136 Maintenance and care The American Automobile Manufacturers Association AAMA issued a gasoline specification to provide information on high quality fuels that optimize t
110. the Check Engine light or the temperature warning light These events could indicate that the emission control system is not working properly If you smell exhaust fumes of any kind inside your vehicle have the dealer inspect and fix your vehicle immediately Do not drive if you smell exhaust fumes These fumes are harmful and could kill you 138 Maintenance and care Do not make any unauthorized changes to your vehicle or engine By law vehicle owners and anyone who manufactures repairs services sells leases trades vehicles or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working Information about your vehicle s emission system is on the Vehicle Emission Control Information Decal located on or near the engine This decal identifies engine displacement and gives some tune up specifications Please consult your Warranty Guide for complete emission warranty information Readiness for inspection maintenance I M testing In some localities it may be a legal requirement to pass an I M test of the on board diagnostic OBD ID system If your check engine service engine soon light is on reference the applicable light description in the Warning Lights and Chimes section of your owners guide Your vehicle may not pass the I M test with the check engine service engine soon light on If the vehicle s powertrain system or its battery has
111. to owners of utility type vehicles Before you drive your vehicle please read this Owner s Guide carefully Your vehicle is not a passenger car As with other vehicles of this type failure to operate this vehicle correctly may result in loss of control or an accident Introduction Be sure to read Driving off road in the Driving chapter as well as the Four Wheeling supplement included with 4WD and utility type vehicles Using your vehicle as a snowplow fp Do not use this vehicle for snowplowing Using your vehicle as an ambulance A Do not use this vehicle as an ambulance Your vehicle is not equipped with the Ford Ambulance Preparation package Electric vehicles For information on operating your Electric Vehicle also refer to the Electric Vehicle Owner s Guide Supplement Instrumentation Headlamp control Instrument cluster pg 16 ps 6 Instrument panel dimmer switch SPEED O D CONT OFF wa a a i i y air bag Turn signal and wiper washer control Speed control pg 47 Deane pg 24 Instrumentation Electronic sound system Auxiliary power point refer to Audio Guide pg 23 pg 24 SD ON PASSENGER AIRBAI limat l Passenger air bag deactivate umake a T switch pg 51 Instrumentation STANDARD INSTRUMENT CLUSTER Te S i 40g BRAKE wx a sPeeD ojo THEFT CONT OFE
112. tomatic transmission or the neutral position manual transmission turn off all accessories and start the engine 2 Let the engine idle for at least one minute 128 Maintenance and care 3 The relearning process will automatically complete as you drive the vehicle e If you do not allow the engine to relearn its idle the idle quality of your vehicle may be adversely affected until the idle is eventually relearned e If the battery has been disconnected or a new battery has been installed the clock and the preset radio stations must be reset once the battery is reconnected e Always dispose of automotive batteries in a responsible manner Follow your community s standards for disposal Call your local recycling center to find out more about recycling automotive batteries WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades Checking the wiper blades If the wiper blades do not wipe properly clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent Rinse thoroughly with clean water To avoid damaging the blades do not use fuel kerosene paint thinner or other solvents Changing the wiper blades When replacing wiper blade assemblies always use a Motorcraft part or equivalent To make replaci
113. tor Vehicle Safety Standard No 109 Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law The temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive speed underinflation or excessive loading either separately or in combination can cause heat buildup and possible tire failure 131 Maintenance and care SERVICING YOUR TIRES Checking the tire pressure e Use an accurate tire pressure gauge e Check the tire pressure when tires are cold after the vehicle has been parked for at least one hour or has been driven less than 5 km 3 miles e Adjust tire pressure to recommended specifications found on the Tire Pressure Label Improperly inflated tires can affect vehicle handling and can fail suddenly possibly resulting in loss of vehicle control Tire rotation Because your vehicle s tires perform different jobs they often wear differently To make sure your tires wear evenly and last longer rotate them as indicated in the Service Guide If you notice that the tires wear unevenly have them checked The following procedure applies to vehicles equipped with single rear wheels if your vehicle is equipped with dual rear wheels it is recommended that only the front wheels be rotated side to side e Four tire rotation S AN K A l I i 132 and care Maintenanc D e Five tire rotat
114. traveled Total gallons used Keep a record for at least one month This will provide an accurate estimate of the vehicle s fuel economy 137 Maintenance and care EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards To make sure that the catalytic converter and other emission control components continue to work properly e Use only unleaded fuel e Avoid running out of fuel e Do not turn off the ignition while your vehicle is moving especially at high speeds e Have the services listed in your Service Guide performed according to the specified schedule The Scheduled Maintenance Services listed in the Service Guide are required because they are considered essential to the life and performance of your vehicle and to its emissions system If other than Ford Motorcraft or Ford authorized parts are used for maintenance replacements or for service of components affecting emission control such non Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire Watch for fluid leaks strange odors smoke loss of oil pressure the charging system warning light
115. und the hips e If you need to lengthen the belt unfasten it and repeat the procedure above To unfasten the belt push in the release button prior to opening the rear door Safety belt extension assembly If the safety belt assembly is too short even when fully extended 20 cm 8 inches can be added to the safety belt assembly by adding a safety belt extension assembly part number 611C22 Safety belt extension assemblies can be obtained from your dealer at no cost Use only extensions manufactured by the same supplier as the safety belt Manufacturer identification is located at the end of the webbing on the label Also use the safety belt extension only if the safety belt is too short for you when fully extended Do not use extensions to change the fit of the shoulder belt across the torso Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts 45 Seating and safety restraints Conditions of operation The driver s safety belt is not The safety belt warning light buckled before the ignition switch illuminates for one to two minutes is turned to the ON position and the warning chime sounds for four to eight seconds The driver s safety belt is buckled The safety belt warning light and while the indicator light is warning chime turn off illuminated and the warning chime is sounding
116. utch pedal 3 Put the gearshift lever in N Neutral 4 Crank the engine and let it idle for a few seconds e Put the gearshift in 1 First or R Reverse 5 Release the clutch slowly while pressing gradually down on the accelerator pedal e Do not drive with your foot resting on the clutch pedal Do not use the clutch to hold your vehicle at a standstill while waiting on a hill These actions may reduce clutch life 72 Driving Recommended shift speeds Upshifts when accelerating for best fuel economy Shift from Transfer case position if equipped E 3 5 Overdrive 4 Parking 1 Apply the brake and shift into N Neutral NS J 73 Driving 2 Engage the parking brake 3 Shift into 1 First 4 Turn the ignition to Off Do not park your vehicle in Neutral it may move unexpectedly and injure someone Use 1 First gear and set the parking brake fully Reverse Ensure that the vehicle is at a complete stop before shifting into R Reverse Failure to do so may damage the transmission Put the gearshift into N and wait at least several seconds before shifting into R You can shift into R Reverse only by moving the gearshift from left of 3 Third and 4 Fourth gears before you shift into R Reverse This is a special lockout feature that protects you from accidentally shifting into R Reverse when you downshift from 5 Overdrive FOUR WHEEL DRIVE 4WD OPERATION IF E
117. ver To avoid injury never run the engine with one wheel off the ground such as when changing a tire VEHICLE LOADING Before loading a vehicle familiarize yourself with the following terms e Base Curb Weight Weight of the vehicle including any standard equipment fluids lubricants etc It does not include passengers or aftermarket equipment 79 Driving Payload Combined maximum allowable weight of cargo passengers and optional equipment The payload equals the gross vehicle weight rating minus base curb weight GVW Gross Vehicle Weight Base curb weight plus payload weight The GVW is not a limit or a specification GVWR Gross Vehicle Weight Rating Maximum total weight of the base vehicle passengers optional equipment and cargo The GVWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver s door pillar GAWR Gross Axle Weight Rating Carrying capacity for each axle system The GAWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver s door pillar GCWR Gross Combined Weight Rating Maximum combined weight of towing vehicle including passengers and cargo and the trailer The GCWR indicates the maximum loaded weight that the vehicle is allowed to tow Maximum Trailer Weight Rating Maximum weight of a trailer the vehicle is permitted to tow The maximum trailer weight rating is determined by subtracting the vehicle curb weight f
118. wing operation 81 Driving Trailer towing table 4x2 manual transmission Maximum Maximum frontal trailer area of trailer m weight kg Ibs ft 0 maximum Regular Cab 4x2 Not recommended for trailer towing 4 800 0 1 580 area of base vehicle 3 0 3 45 Equal to frontal 5 000 0 1 740 area of base vehicle 0 2 3 3 73 2 721 0 1 225 4 64 50 6 000 0 2 700 3 08 2 267 0 753 Equal to frontal 5 000 0 1 660 area of base vehicle 3 175 7 000 0 1 651 0 3 640 4 64 50 Regular Cab 4x2 Splash or Special Suspension 2 5L 3 73 2177 0 680 Equal to frontal P gt EE Gaon ormo an obase venice 3 0L 3 73 2 449 0 907 Equal to frontal gt gt PP eim zomr areaar use venicl 4 0L 3 08 2 267 0 717 Equal to frontal 4 gt S cm wiss area ar unse venici 5 500 0 2 000 area of base vehicle SuperCab 4x2 2 5L 3 73 2 177 0 626 Equal to frontal A l a a esere vee 5 000 0 1 540 area of base vehicle 4 0L 3 08 2 267 0 635 Equal to frontal SS 5 000 0 1 400 area of base vehicle 3 55 3 175 7 000 0 1 542 0 3 400 4 64 50 82 Driving Trailer towing table 4x2 manual transmission SuperCab 4x2 Splash or Special Suspension 3 0L 3 73 2 540 0 907 Equal to frontal gt M PP Loam ozor fare ot base vehicle 4 0L 3 08 2 267 0 635 Equal to frontal 4 0L 3 55 2 540 0 907 Equal to frontal Optional payload is not available on 4x2 Splash or Special Suspension therefore maximum trailer
119. wing trailers up to 907 kg 2 000 Ib use a weight carrying hitch and ball which uniformly distributes the trailer tongue loads through the underbody structure Use a frame mounted weight distrubuting hitch for trailers over 907 kg 2 000 Ib Do not install a single or multi clamp type bumper hitch or a hitch which attaches to the axle Underbody mounted hitches are acceptable if they are installed properly Follow the towing instructions of a reputable rental agency Whenever a trailer hitch and hardware are removed make sure all mounting holes in the underbody are properly sealed to prevent noxious gases or water from entering Safety chains Always connect the trailer s safety chains to the vehicle To connect the trailer s safety chains cross the chains under the trailer tongue and allow slack for turning corners If you use a rental trailer follow the instructions that the rental agency gives to you Trailer brakes Electric brakes and manual automatic or surge type brakes are safe if installed properly and adjusted to the manufacturer s specifications The trailer brakes must meet local and Federal regulations 87 Driving Do not connect a trailer s hydraulic brake system directly to your vehicle s brake system Your vehicle may not have enough braking power and your chances of having a collision greatly increase The braking system of the tow vehicle is rated for operation at the GVWR not GCWR Trailer l
120. you use a brake fluid that is not DOT 3 you will cause permanent damage to your brakes A Do not let the reservoir for the master cylinder run dry This may cause the brakes to fail CLUTCH FLUID IF EQUIPPED During normal operation the fluid level in the clutch reservoir will slowly rise If the fluid level drops maintain the fluid level at the step in the reservoir Use only a DOT 3 brake fluid designed to meet Ford specifications Refer to Capacities and specifications 1 Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir 2 Remove cap 3 Add fluid until the level reaches the FULL line 119 Maintenance and care WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel The reservoir is highlighted with a G7 symbol If the level is low add enough fluid to fill the reservoir In very cold weather do not fill the reservoir all the way Do not put engine coolant in the container for the windshield washer fluid 120 Maintenance and care ENGINE COOLANT Check the level of the engine coolant in the reservoir at least once a month Be sure to read and understand Precautions when servicing your vehicle in this chapter If the engine coolant has not been checked at the above recommended interval the engine coolant reservoir may become empty If this occurs add engine coolant to the reserv

Ford 1998 Ranger Automobile User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents