Flymo EM032 Lawn Mower User Manual
Contents
1. L Height of cut is adjusted by raising or lowering the Front and Rear Wheels There are five heights of cut on this product NOTE A medium height of cut is recommended for most lawns The quality of your lawn will suffer and collection will be poor if you cut too low HEIGHT OF CUT Low Low to Medium Medium Medium to High High WHEELS POSITION Front position 2cm Rear position 2cm Front position 2cm Rear position 4cm Front position 4cm Rear position 4cm Front position 4cm Rear position 6cm Front position 6cm Rear position 6cm Starting and Stopping To Start your Lawnmower 1 Form loop in mains cable and push the loop through the slot M 2 To secure position loop over the hook and pull the cable back through the slot N 3 Connect plug to mains and switch on 4 Tilt the handle downwards to slightly raise the front of the lawnmower and to reduce the risk of lawn damage whilst starting The switchbox is provided with a lock off button P1 to prevent accidental starting 5 Press and hold the lock off button P on the switch box then squeeze one of the Start Stop levers towards the upper handle Q 6 Continue to squeeze the start stop lever towards the upper handle and release the lock off button R 7 Lower the lawnmower to its proper operating posi tion and commence mowing e NOTE There are two start stop levers fitted Either one can be used for starting the lawn mow2. 2 Using a soft brush remove grass clippings from all air intakes W2 the discharge chute W3 and the grass box W4 3 Visimo Only Using a soft brush remove grass clip pings from the vision window W5 4 Wipe over the surface of your lawnmower with a dry cloth W6 e IMPORTANT Never use water for cleaning your lawn mower Do not clean with chemicals including petrol or solvents some can destroy critical plastic parts Storing your Cable Visimo amp Rollermo only e Your electric cable can be wrapped around the cable wrap wing knobs to enable tidy and safe storage X1 Storing your Lawnmower e Loosen the wing knobs to enable the handles to be folded over the product X2 e Store in a dry place where your lawnmower is pro tected from damage At the End of the Mowing Season 1 Replace blade bolts nuts or screws if necessary 2 Clean your lawnmower thoroughly 3 Make sure that the electric cable is stored correctly to prevent damage Visimo Only A K Om s M ml _ gogon yt gaon U omon Fault Finding Hints Fails to Operate 1 Is the correct Starting procedure being followed See To Start your Lawnmower 2 Is the Power Turned On 3 Check the fuse in the plug if blown replace 4 Fuse continues to blow Immediately disconnect from the mains electricity sup ply a
3. object Do not use your lawnmower until you are sure that the entire lawnmower is ina safe operating condition if the lawnmower starts to vibrate abnormally Check immediately Excessive vibration can cause injury Maintenance and storage 1 2 3 4 Keep all nuts bolts and screws tight to be sure the lawnmower is in safe working condition Check the grassbox frequently for wear or deterioration Replace worn or damaged parts for safety Only use the replacement blade and blade bolt specified for this product Be careful during adjustment of the lawnmower to prevent entrapment of the fingers between moving blades and fixed parts of the machine No earth required Flymo products are double insulated to EN60335 and under no circumstances should an earth be connected to any part of the product Ensure the mains voltage suits your product IMPORTANT The wires in the mains lead are coloured in accor dance with the following code BLUE NEUTRAL BROWN LIVE The wire which is coloured BLUE must be connected to the Terminal which is marked with the letter N or coloured BLACK The wire which is coloured BROWN must be con nected to the Terminal which is marked with the let ter L or coloured RED It is important that the outer sheath is clamped cor rectly into the 3 pin plug If in doubt consult your local Service Repairer or qualified electrician before the machine is used A 13 Amp fuse m
4. the blade 3 Before using the machine and after any impact check for signs of wear or damage and repair as necessary 4 Replace worn or damaged blades together with their fixings in sets to preserve balance Use 1 Use the lawnmower only in daylight or good artificial light CABLES IMPORTANT Use only 1 00mm size cable up to 40 metres length maximum Maximum rating 1 00mm size cable 10 amps 250 volts AC 3 YOUR PRODUCT IS SUPPLIED WITH CABLE WIRED DIRECTLY INTO THE PRODUCT Flymo Mains Cables and Extension Cables are avail able from your local Approved Service Centre Do not wire an extension cable directly to your prod uct yourself Please contact your local Approved Service Centre for further information on the connec tors and kits available Only use extension cables specifically designed for outdoor use CONNECTORS IMPORTANT Flymo connectors are suitable for use with 2 core cable only Under no circumstances should these connectors be used for earthed products All Flymo connectors and cables are of splashproof construction They are not waterproof and must not be left outside permanently nor should they be sub merged or immersed in water Do not let cable lay or trail through pools of water or splashed with water from hose pipes MAINS PLUG REPLACEMENT IMPORTANT If the plug supplied is cut off it should be destroyed There is an electric shock hazard if a cut off plug is in
5. your household waste disposal service or the shop where you indicates that this product may not be treated as household purchased the product waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Guarantee amp Guarantee Policy If any part is found to be defective due to faulty manufacture within the guarantee period Husqvarna Outdoor Products through its Authorised Service Repairers will effect the repair or replacement to the customer free of charge provid ing a The fault is reported directly to the Authorised Repairer b Proof of purchase is provided c The fault is not caused by misuse neglect or faulty adjustment by the user d The failure has not occurred through fair wear and tear e The machine has not been serviced or repaired taken apart or tampered with by any person not authorised by Husqvarna Outdoor Products f The machine has not been used for hire g The machine is owned by the original purchaser h The machine has not been used commercially 7 This guarantee is additional to and in no way diminish es the customers statutory rights Failures due to the following are not covered therefore it is important that you read the instructions contained in this Operator s Manual and understand how to operate and main tain your machine Failures not covered by guarantee 4 Replacing worn or damaged bl
6. VISIMO KA EASIMO a 2 For all customer enquiries or for replacement parts contact 0870 609 1901 A www flymo com D lt customer services husqvarna co uk Carton Contents start stop lever cable clip x ee washer x 4 bolt x 2 wingknob x 4 AA D G grassbox tongue safety flap fil motor cover Bay 4 SS lock off YJ button grassbox handle upper handle ION grassbox upper m grassbox switchbox lower electric cable with moulded on plug lower handle x 2 instruction IMPORTANT IF ANY PARTS ARE MISSING CONTACT Telephone 0870 609 1901 Fax 0870 609 1902 Please check the contents of the carton are correct BEFORE assembling your new Flymo product Parts Pack is packaged underneath the deck of the product The Loose Husqvarna Outdoor Products Customer Service Department direct Safety Explanation of Symbols on your product Read the user instructions carefully to make sure you understand all the controls and what they do Keep bystanders away Do not mow whilst people especially children or pets are in the mowing area Always keep the lawnmower on the ground when mowing Tilting or lifting the lawnmower may cause stones to be thrown out General 1 Never allow children or people unfamiliar with these instructions to use the mower Local regulations may restrict the age of the operator 2 Only use the lawnmowe
7. ades Failures as a result of not reporting an initial fault i Failures as a result of sudden impact 4 Failures as a result of not using the product in accor dance with the instructions and recommendations con tained in this Operator s Manual e Machines used for hire are not covered by this guaran tee i The following items listed are considered as wearing parts and their life is dependent on regular mainte nance and are therefore not normally subject to a valid warranty claim Blades Electric Mains cable Caution Husqvarna Outdoor Products does not accept liability under the warranty for defects caused in whole or part directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Husqvarna Outdoor Products or by the machine having been modified in any way EC Declaration of Conformity I the undersigned M Bowden of Husqvarna I the undersigned M Bowden of Husqvarna I the undersigned M Bowden of Husqvarna Outdoor Products Aycliffe Industrial Park Outdoor Products Aycliffe Industrial Park Outdoor Products Aycliffe Industrial Park NEWTON AYCLIFFE Co Durham DL5 6UP NEWTON AYCLIFFE Co Durham DL5 6UP NEWTON AYCLIFFE Co Durham DL5 Certify that the product Certify that a sample of the above product has 6UP Certify that a sample of the above Electric Wheeled Lawnmower been tested using directive 81 1051 EEC as a product has bee
8. age or ageing Do not use the lawnmower if the electric cables are damaged or worn Immediately disconnect from the mains electricity supply if the cable is cut or the insulation is dam aged Do not touch the electric cable until the elec trical supply has been disconnected Do not repair a cut or damaged cable Replace it with a new one Your extension cable must be uncoiled coiled cables can overheat and reduce the efficiency of your mower Keep cable away from lawnmower always work away from the power point mowing up and down never in circles Do not pull cable around sharp objects Always switch off at the mains before disconnecting any plug cable connector or extension cable Switch off remove plug from mains and examine electric supply cable for damage or ageing before winding cable for storage Do not repair a damaged cable replace it with a new one Use only Flymo replacement cable Always wind cable carefully avoiding kinking Never carry the product by the cable Never pull on the cable to disconnect any of the plugs Use only on AC mains supply voltage shown on the product rating label Flymo Products are double insulated to EN60335 Under no circumstance should an earth be connect ed to any part of the product Preparation 1 While using your product always wear substantial footwear and long trousers 2 Make sure the lawn is clear of sticks stones bones wire and debris they could be thrown by
9. arp edges could cause injury USE GLOVES Removing the Blade 1 To remove the blade bolt hold the blade firmly with a gloved hand and with a spanner loosen the blade bolt by turning it anti clockwise T Remove the blade bolt washer and blade T Inspect for damage and clean as necessary In the event of a blade becoming difficult to remove insert a screwdriver V1 into the hole V2 to lock the drive then use a spanner 13mm A F to loosen the blade bolt by turning the spanner anti clockwise oY Ensure the screwdriver is removed before atempting i to turn on the machine ASS AUN Renew your metal blade after 50 hours mowing or 2 years whichever is the sooner regardless of condi tion If the blade is cracked or damaged replace it with a new one Fitting the Blade 1 Fit the blade to the shaft with the sharp edges of the blade pointing away from the shaft and you are able to read the text on the blade This side to grass 2 Re assemble blade bolt through the washer and the blade 3 Hold the blade firmly with a gloved hand and tighten the blade bolt firmly with a spanner Do not over tighten Caring for your Lawnmower Cleaning e USE GLOVES e IMPORTANT It is very important that you keep your lawnmower clean Grass clippings left in any of the air intakes or under the deck could become a poten tial fire hazard 1 Remove grass from under the deck with brush W1
10. er IMPORTANT Do not use the start stop levers intermittently To Stop your Lawnmower 1 Release the pressure on the Start Stop lever How to Mow 1 Start mowing the edge of the lawn nearest to the power point so the cable is laid out on the lawn you have already cut S 2 Mow twice a week during the growing season your lawn will suffer if more than a third of its length is cut at one time and this may also result in poor collection Do Not Overload Your Mower Mowing long thick grass may cause the motor speed to drop you will hear a change in the motor sound If the motor speed drops you may overload your lawnmower which may cause damage When mow ing in long thick grass a first cut with the cutting height set higher will help reduce the load See Cutting Height Adjustment Thermal Cut Out The Motor is protected by a Thermal Cut Out which is activated when the blade becomes jammed or if the motor is overloaded When this occurs stop and remove the plug from the power supply The Thermal Cut Out will only reset when the start stop lever is released Clear any obstruction and wait for a few min utes for the Thermal Cut Out to reset before continuing to use the mower eg Switch off wait until the blade has stopped SS rotating and disconnect from the mains electrici blade bolt ty supply BEFORE attempting to remove or refit the blade Always handle the blade with care sh
11. n tested using ISO 5349 as Husqvarna Outdoor guide The maximum A weighted sound pres a guide The maximum weighted root mean Products sure level recorded at operator position under square value of vibration recorded at opera Conforms to the specifications of Directive free field semi anechoic chamber conditions tor s hand position was 2000 1 4 EC was Type of Cutting Device Rotary Blade Identification of Series See Product Rating Label Conformity Assessment Procedure ANNEX VI Speed of Rotation of Cutting Device Notified Body Intertek Cleeve Road Leatherhead Guaranteed sound power level Surrey KT22 7SB England Measured Sound Power Level Other Directives eee0e 98 37 EC 89 336 EEC 2006 95 EC 80 2 dB A amp applicable standards EN61000 3 2 EN61000 3 3 a a 2 5 m s EN55014 1 EN55014 2 EN836 EN60335 1 EN60335 2 77 Weigh hisses ais teeisns ce cssets cecescsescestesiacevesesseeses 8 92kg 842kg 8 85kg EN50366 Voltage Hertz 230V 50HZ 1200W 1000W 900W Newton Aycliffe 15 02 2007 M Bowden Research amp Development Director Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice Husqvarna Outdoor Products Aycliffe Industrial Park NEWTON AYCLIFFE Co Durham DL5 6UP ENGLAND LAY Telephone 0870 609 1901 Fax 0870 609 1902 5108035 01 4
12. nd consult your local approved Service Centre Poor Grass Collection 1 Disconnect from the mains electricity supply 2 Clean the outside of the air intakes the discharge chute and the underside of the deck 3 Raise to a higher height of cut See Cutting Height Adjustment 4 If poor collection persists Immediately disconnect from the mains electricity sup ply and consult your local approved Service Centre Excessive Vibration 1 Disconnect from the mains electricity supply 2 Check that the blade is fitted correctly 3 If the blade is damaged or worn replace it with a new one 4 If vibration persists Immediately disconnect from the mains electricity sup ply and consult your local approved Service Centre Lawnmower becomes heavy to push 1 Disconnect from the mains electricity supply 2 In long grass or uneven ground the height of cut should be raised to a higher position See Cutting Height Adjustment 3 Check that the wheels and rollers can rotate freely 4 If problem persists Immediately disconnect from the mains electricity sup ply and consult your local approved Service Centre Service Recommendations 1 We strongly recommend that your product is serviced at least every twelve months more often in a profes sional application 2 Always use genuine Spare Parts 3 Prepacked spares are available from most Husqvarna Outdoor Products stockists 4 Your product is uniquely identified b
13. r in the manner and for the If not used properly this lawnmower can be dangerous This lawnmower can cause serious injury to the operator and others the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this lawnmower The operator is responsible for following the warning and safety instructions in this manual and on the lawnmower provided by the manufacturer are in the correct position Never use the mower unless the grassbox or guards Switch off Remove plug from mains before adjusting cleaning or if cable is entangled or damaged Keep the cable away from the blade Beware of severing toes or hands Do not put hands or feet near a rotating blade Keep the cable supply away from the cutting means functions described in these instructions 3 Never operate the lawnmower when you are tired ill or under the influence of alcohol drugs or medicine 4 The operator or user is responsible for accidents or hazards occurring to other people or their property Electrical 1 10 11 13 14 The British Standards Institute recommend the use of a Residual Current Circuit Device R C D witha tripping current of not more than 30mA Even with a R C D installed 100 safety cannot be guaran teed and safe working practice must be followed at all times Check your R C D every time you use it Before use examine cable for damage replace it if there are signs of dam
14. serted into a 13 amp socket 2 Avoid operating your lawnmower in wet grass where feasible 3 Take care in wet grass you may lose your footing 4 On slopes be extra careful of your footing and wear non slip footwear 5 Mow across the face of slopes never up and down 6 Exercise extreme caution when changing direction on slopes Walk never run 7 Mowing on banks and slopes can be dangerous Do not mow on banks or steep slopes 8 Do not walk backwards when mowing you could trip 9 Never cut grass by pulling the mower towards you 10 Switch off before pushing the mower over surfaces other than grass 11 Never operate the lawnmower with damaged guards or without guards in place 12 Keep hands and feet away from the cutting means at all times and especially when switching on the motor 13 Do not tilt lawnmower when the motor is running except when starting and stopping In this case do not tilt more than absolutely necessary and lift only the part which is away from the operator Always ensure that both hands are in the operating position before returning the appliance to the ground 14 Do not put hands near the grass discharge chute 15 Never pick up or carry a mower when it is operating or still connected to the mains supply 16 Remove the plug from the mains before leaving the mower unattended for any period before clearing a blockage before checking cleaning or working on the appliance if you hit an
15. t clicks securely into posi tion E Starting at the rear of the grassbox locate the grassbox upper into the grassbox lower by aligning the clips F1 Ensure all clips are cor rectly located F2 before clicking into position Clip the two halves together ensuring all clips are securely connected Grassbox Visimo Only o grassbox empty grassbox full AD Fitting Fully Assembled Grassbox to Lawnmower 1 2 3 Lift safety flap G1 Make sure the discharge chute is clean and free from debris G2 Locate fully assembled grassbox onto 2 location points G3 at the rear of the deck as illustrated in pic H Locate safety flap onto the top of the grassbox Ensure the grassbox is securely located IMPORTANT AFTER FITTING ENSURE NO GAP REMAINS BETWEEN THE SAFETY FLAP AND THE GRASSBOX Removal is the reverse procedure For larger areas of grass where grass collection is not required you can use your lawnmower without the grassbox Ensure the Safety Flap is fully closed The design of the safety flap per mits the cut grass to be discharged downward behind the machine Grassbox Full Window Visimo Only As the grassbox fills up grass will be visible through the window J When the window grassbox is full it is time to empty the grassbox Cutting Height Adjustment Cutting Height Adjustment K amp
16. ust be fitted to the Mains Plug The normal plug fuse and household fuse only pro tect the electrical equipment and are not a safeguard against electrocution If your product is hard wired i e non detachable mains electric cable a conversion kit and exten sion cable is available from all Approved Service Centres which can be found in your local Yellow Pages Assembly Instructions The Loose Parts Pack is packaged under neath the deck Assembly of Lower Handles to Deck 1 Place the bolt A2 through the hole in the lower handle A1 until the lower handle fits into the recess A3 Place the washer B1 and the wing knob B2 on to the bolt and tighten the wing knob Repeat on the other side Assembly of Upper Handles to Lower Handles 1 Ensure the upper handle is located correctly with the lock off button on the switchbox upper most Ensure the upper handle C1 and the lower handle C2 are aligned correctly Fit the bolts C3 washers C4 and wing knobs C5 Tighten the wing knob Fit the cable to the handles with the clips provid ed Make sure the cable is not trapped between the upper and lower handles Grassbox Assembly 1 Slide the grassbox tongue into the slots in the grassbox lower until it clicks securely into posi tion D Push the grassbox handle into the slots in the grassbox upper until i
17. y a silver and black product rating label 5 If you have a problem with your machine contact your local Approved Service Centre ensuring you have full details of your product as described on the product rat ing label 6 Should it be necessary for work to be carried out by your Service Centre it is important to take your complete machine including cable and any extension cables used A network of specialist dealers can be found in your local Yellow Pages To obtain service on your product simply telephone or visit your local Service Centre Should you require service under the terms of our guarantee the Service Centre will require proof of purchase All of the centres listed stock genuine Spare Parts NOTE Our Service Repairers act on their own behalf and are not empowered to commit or legally bind Husqvarna Outdoor Products in any manner whatsoever Environmental Information Awareness of the environment must be considered when disposing of end of life product If necessary contact your local authority for disposal information r The symbol X on the product or on its packaging By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council office
Download Pdf Manuals
Related Search