Fantom Vacuum FM718 Vacuum Cleaner User Manual
Contents
1. Fantom CYCLONIC BAGLESS UPRIGHT OWNER S MANUAL d Model FM718 120V 60Hz 12 Amps FANTOM 94 Main Mill Street Door 16 Plattsburgh NY 12901 Tel 1 800 275 9251 www fantom com Model FM718 ONE 1 YEAR LIMITED WARRANTY FANTOM warrants this product to be free from defects in material and workmanship for a period of one 1 year from the date of the original purchase This warranty applies only to normal domestic household use Should your appliance fail to operate properly while in use under normal household conditions within the one 1 year warranty period return the complete appliance and accessories freight prepaid to FANTOM 94 Main Mill Street Door 16 Plattsburgh NY 12901 Should the appliance is found to be defective in material or workmanship FANTOM will repair or replace it free of charge Proof of purchase date and 16 95 to cover the cost of return shipping and handling must be included Non durable parts including without limitation drive belts rotating brushes bulbs and electrical parts which normally require replacement are specifically excluded from warranty The liability of FANTOM is limited solely to the cost of the repair or replacement of the unit at our option This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes This limited warranty does not cover damage caused by misuse abuse negligent h2. Motor Filter Warning To reduce the risk of electric shock the power cord must be disconnected before removing the dust cup HEPA filter changing the filters or performing maintenance trouble shooting checks The pre motor filter is located in the vacuum underneath the dust cup Please note that this filter is a washable filter and can be cleaned by rinsing under lukewarm water Always allow the pre motor filter to air dry for 24 hours before replacing in the vacuum Do not use a hair dryer to dry it Air dry only To remove the pre motor filter 1 Remove the dust cup See instructions on page 5 for removing the dust cup 2 Hold the Pre Motor filter cover and turn counter clockwise to unlock and lift to remove Fig 16 3 Remove the pre motor filter and clean by rinsing under lukewarm water 4 After air drying for 24 hours replace in the vacuum 5 To replace the pre motor filter cover insert the locking lugs into Phe holes and turn clockwise to ock Filter Changing amp Cleaning the Exhaust Filter Warning To reduce the risk of electric shock the power cord must be disconnected before removing the dust cup HEPA filter changing the filters or performing maintenance trouble shooting checks The exhaust filter is located on the front of the unit below where the dust cup is To remove the exhaust filter you must first remove the filter cover 1 Check the exhaust filter frequently and replace
3. OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Cleaning the Dust Cup Warning To reduce the risk of electric shock the power cord must be disconnected before removing the dust cup HEPA filter changing the filters or performing maintenance trouble shooting checks The dust cup can be 4 washed in lukewarm water Do not use strong aa detergents Ensure that the dust cup is fully dry before putting back on the vacuum cleaner j Fig 18 Do not wash in r dishwasher Fig 18 Motor Thermostat Important This unit is equipped with a motor protective thermostat If for some reason the vacuum cleaner should overheat the thermostat will automatically turn the unit off Should this occur e Push the On Off button once e Disconnect the plug from the power source e Check the source of overheating problem i e clogged hose or filter If clogged hose or filter is found unclog the hose and replace the filters e Wait at least 45 minutes before attempting to reuse the vacuum After unit has cooled down for 45 minutes plug in the cleaner and push the On Off button The vacuum should start again e f the vacuum still does not start contact FANTOM customer service at 1 800 275 9251 Cleaning amp Changing the Belt A Warning To reduce the risk of electric shock the power cord must be disconnected before removing the dust cup HEPA filter changing the filters or performing maintenance tro
4. 11 Loop the new belt first over the motor drive shaft and then over the agitator pulley Fig 22 12 Insert the right side of the brush bar in first by placing the end cap down into the slot and then do the same with the left side Press firmly to make sure that each end is completely inserted 13 Check to make sure that the belt is centered on the agitator pulley and that the brush bar turns 14 Replace the belt cover 15 Replace the power head cover and turn the unit over carefully 16 Replace the lower plate screwing in the four 4 outer screws first 17 When screwing in the center screw hold the carpet height adjustment knob from the outside and screw in the last screw 18 Replace the lower plate 19 Once the lower plate is attached replace the base plate with the four 4 screws Changing the Headlight Bulb Warning To reduce the risk of electric shock the power cord must be disconnected before removing the dust cup HEPA filter changing the filters or performing maintenance trouble shooting checks 1 Turn unit Off and unplug from wall outlet 2 With a flat head screw driver snap off the lens cover by pressing down on the two notches on the lens cover Fig 23 3 Lift off the head light lens Fig 23 4 Remove the light bulb by pulling it out carefully 5 Replace the new bulb by pushing it in 6 Replace the head light lens by pushing it in so that it snaps back in place
5. Do NOT operate cleaner in bare feet or when wearing open toe shoes Do NOT pick up hot coals cigarette butts matches or any hot smoking or burning objects Do NOT pick up hard or sharp objects such as glass nails screws coins etc 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Do NOT use without filters in place Use ONLY filters and accessories provided by FANTOM Failure to do so will void the warranty Turn off all controls before plugging or unplugging vacuum cleaner into electrical outlet Use extra care when vacuuming on stairs Do NOT pick up flammable or combustible materials lighter fluid gasoline kerosene etc or use in the presence of explosive liquids or vapor Do NOT pick up toxic material chlorine bleach ammonia drain cleaner etc Do NOT use in an enclosed space filled with vapors given off by oil based paints paint thinner moth proofing substances flammable dust or other explosive or toxic vapors Use only on dry indoor surfaces Do NOT use for any purpose other than described in this user s guide The use of an extension cord is not recommended Do NOT put any objects into openings Do NOT use with any opening blocked Keep free of dust lint hair and anything else that may reduce air flow Store your appliance indoors in a cool dry area Keep your work area well lit Do NOT immerse the vacuum into water or other liquids Keep end
6. with new filters when dirty 2 Remove the exhaust filter cover Fig 17 Remove the exhaust filter Rinse in lukewarm water and let the filter air dry for 24 hours before re installing into the vacuum Do not use a washing machine to rinse the filter Do not use a hair dryer to dry the filter Air dry only Never operate the vacuum without ALL the filters in place 5 When the filter is dry replace into the vacuum and replace the filter cover Note A severely soiled or clogged filter should be thoroughly washed with fresh tepid water A mild detergent may be used if required pa
7. andling or damage due to faulty packaging or mishandling in transit This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs service or alterations to the product or any of its parts which have been performed by a repair person not authorized by FANTOM This warranty is extended to the original purchaser of the unit and excludes all other legal and or conventional warranties The responsibility of FANTOM if any is limited to the specific obligations expressly assumed by it under the terms of the limited warranty In no event is FANTOM liable for incidental or consequential damages of any nature whatsoever Some states do not permit the exclusion or limitation of incidental or consequential damages so the above may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Important Carefully pack item to avoid damage in shipping Be sure to include proof of purchase date and to attach tag to item before packing with your name complete address and phone number with a note giving purchase information model number and what you believe is the problem with item We recommend you insure the package as damage in shipping is not covered by your warranty Mark the outside of your package ATTENTION CUSTOMER SERVICE We are constantly striving to improve our products therefore the specifications contained herein are subje
8. ct to change without notice Printed in China 12 IMPORTANT SAFETY INSTRUCTIONS When using your Bagless Upright Vacuum basic safety precautions should always be observed including the following WARNING To reduce the risk of fire electrical shock or injury 1 10 11 12 Do NOT leave vacuum cleaner unattended when it is plugged in Unplug from outlet when not in use and before removing filters To reduce the risk of electric shock do NOT use outdoors or on wet surfaces Do NOT allow children to use as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only manufacturer s recommended attachments Do NOT use with damaged cord or plug Do NOT use vacuum cleaner if it has been dropped damaged left outdoors or dropped into water Return appliance to FANTOM for examination repair or adjustment Do NOT pull or carry by cord Do NOT use cord as a handle close a door on cord or pull cord around sharp edges or corners Do NOT run appliance over cord Keep cord away from heated surfaces Do NOT unplug by pulling on cord To unplug grasp the plug not the cord Do NOT handle plug or vacuum cleaner with wet hands Do NOT use the vacuum cleaner to pick up large objects or objects that are likely to damage the vacuum cleaner Keep hair loose clothing fingers feet and all parts of body away from openings rotating agitator and other moving parts
9. d thoroughly and was in good operating condition when it was shipped from the factory If a minor problem occurs it usually can be solved quite easily when the cause is found Therefore this checklist is provided for your convenience PROBLEM POSSIBLE CAUSE POSSIBLE Cleaner Won t Run Cleaner Won t Pick Up Cleaner Picks Up Moveable Rugs Or Pushes Too Hard Agitator Does Not Turn Air Flow Restricted With Attachment Use Sound Changes OONDOARWN gt Not properly plugged into wall outlet No electricity in wall outlet On Off switch not turned on Motor thermostat tripped Blown fuse tripped breaker Full or clogged dust cup Wrong pile height setting Clogged nozzle Clogged dust inlet port Clogged hose Broken belt Hose not inserted fully Dirty filters HEPA filter needs cleaning or replacing HEPA filter frame needs cleaning Wrong pile height setting Broken belt Belt installed incorrectly Attachment use restricts air flow New carpet debris clogging air path 10 Plug in firmly Check fuse or breaker Push on off switch to on Reset motor thermostat page 8 Reset circuit breaker or replace fuse Clean dust cup page 5 Adjust setting page 5 Remove obstruction Remove power head cover and remove obstruction Remove obstruction Replace belt page 8 Push hose in securely Clean change filters page 7 Clean or replace HEPA filter pag
10. e 6 Clean HEPA filter frame page 6 Adjust setting page 5 Replace belt page 8 Check belt changing and agitator cleaning page 8 Check attachment page 4 Remove obstruction GETTING TO KNOW YOUR CYCLONIC BAGLESS Upper Handle On Off Switch Dust Cup Release Button Dust Cup HEPA Filter Frame Carpet Height Selector Furniture Guard Head Light Motorized Power Head One OO a Ne Technical Specifications 120V 60HZ Voltage Power 12 Amps UPRIGHT un ASS Wipe Wp SS ae ES 5 Flexible Hose Power Cord Quick Release Power Cord Holder Round Brush Upholstery Brush Crevice Tool Extension Tubes x2 Hose Connector Carpet to Floor Selector Note Illustrations may differ from actual unit OPERATING INSTRUCTIONS Assembling Your Vacuum Cleaner Note Do not plug the power cord into an electrical outlet until the vacuum is fully assembled Handle Assembly 1 Carefully unpack all components set aside packaging 2 Lift vacuum body to upright position 3 Remove the screw 1 that comes attached to the z body 4 From the rear of the vacuum align amm 9 the handle with groove and slide onto vacuum If necessary use fi thumb and finger Fig 1 pressure to slide handle into position 5 Once handle is in place secure the handle with the screws 2 Fig 1 Caution Do not over tighten Over tightening could strip the screw
11. e dust cup out Fig 4 from the vacuum Fig 7 Suggested Pile Height Setting 3 To empty the dust cup hold it by You may need to raise the height of the the handle over a garbage can vacuum to make some jobs easier and press on the trap door such as scatter rugs and longer pile release button to empty Fig 8 carpets Suggested settings are a AW n CA o m oe ee Carpet Hard wa Carpet Floor Tools HIGH shag carpet long pile plush scatter rugs tools MED medium to long pile LOW short to medium pile E E7 bare floors Fig 6 Fig 7 FLOOR very low pile bare floors to the desired setting Fig 4 when the dirt level reaches the FULL Place unit in HIGH setting when using attachments to prevent possible floor damage Always set the Carpet to Floor Mee selector to Floor setting when using the accessories Fig 5 Attention Special care is required when vacuuming certain types of carpet or floor covering Always check the carpet or floor covering manufacturer s recommended cleaning instructions before vacuuming Trap Door Release OPERATING INSTRUCTIONS Cleaning the HEPA Dust Cup Filter Please Note The white material in the OPERATING INSTRUCTIONS Pre Motor rr Cleaning the Secondary Filter IMPORTANT PI N The Ri bl HEPA filter will discolor over time This is Filter T HEPA Dust n Filter eA NORMAL and will NOT affect the ue i sie tea one j Cover most of the tiniest d
12. holes Do not operate the vacuum without the handle screws in place Cord Assembly 1 Make sure that the quick release cord holder is in the upright position 2 Remove the wire tie from the power cord 3 Wrap the cord into place by wrapping it in a clockwise direction around the quick release cord holder and the lower cord holders Fig 2 4 Turn the quick Fig 2 release cord holder to the left or to the right to unwrap the power cord Fig 2 Warning Always make sure that the vacuum is turned off before unplugging Using the Attachments 1 Place vacuum in its upright position Make sure that the vacuum cleaner is NOT plugged into the electrical outlet when adding or removing accessories 2 Turn the carpet height selector to the highest position and set the Carpet to Floor selector to the Floor position 3 Remove the hose connector from the rear of the unit and push in the desired attachment firmly onto the end of the hose 4 If additional length is required attach the extension tubes to the end of the hose and then attach the crevice tool round brush or upholstery brush to the end of the extension tube Warning Avoid tipping the vacuum or setting it on furniture fringed area rugs or carpeted stairs while you are using the hose with the attachments When using the unit to vacuum floors or with attachments set the Carpet to Floor Selector to the Floor position This will stop
13. of hose wands and other openings away from your face and body To avoid damaging the carpet keep the vacuum cleaner head moving at all times SAVE THESE INSTRUCTIONS For Household Use Only WARNING To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other polarized outlet only one way This plug will fit in a If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do NOT modify the plug in any way Rev 01 04A PRECAUTIONARY MEASURES Important If the suction opening in the unit the hose or the extension tube become blocked switch off the vacuum cleaner and remove the blocking substance before you start the unit again Do not operate the vacuum cleaner to close too heaters or radiators Before inserting the power plug into the wall outlet make sure that your hands are dry Keep hair loose clothing fingers feet and all parts of body away from openings rotating agitator and other moving parts 5 When pulling out the power plug from the wall outlet pull the plug not the power cord Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not run appliance over power cord Do not use without dust cup filter or filters in place Before you start vacuuming make sure to remove large o
14. r sharp objects that might damage the vacuum Fantom CYCLONIC BAGLESS UPRIGHT TO ORDER REPLACEMENT FILTERS OR BELTS OR FOR TECHNICAL SUPPORT for Model FM718 Call 1 800 275 9251 Monday to Friday 8 30 A M 5 00 P M Eastern Standard Time or visit our website www fantom com Please Note Filter Ring Pre Motor Secondary and Exhaust Filters are washable They should however be replaced every three 3 months to ensure peak performance of your vacuum The HEPA Dust Cup Filter may be washed It should however be replaced every three 3 to six 6 months depending on amount of use to ensure peak performance of your vacuum We recommend washing it once a month or when suction appears to be reduced To wash your HEPA Dust Cup Filter hold filter cartridge by frame flange and rinse under a tap until all observable dirt has been removed Some discoloration of the HEPA filter material may occur this is normal and will not affect the filter s performance When finished shake off excess water Do NOT wash in dishwasher It is important that when you wash the HEPA dust cup filter filter ring secondary filter pre motor filter or the exhaust filter you allow them to dry COMPLETELY before using again We recommend 24 hours to air dry DO NOT DRY IN DRYER Important Make sure that ALL washable Filters are completely dry before inserting back in the vacuum 11 PROBLEM SOLVING This appliance was inspecte
15. the beater brush from rotating When vacuuming carpets avoid leaving the vacuum in one place for an extended period of time particularly on thick carpet Caution Do NOT pull the vacuum cleaner around the room by the hose as it could tip over and cause damage When using the attachments do NOT over extend the hose length when reaching Trying to reach beyond the hose reach could cause the vacuum to tip over How to Start The upright vacuum can be used on multiple types of carpeting bare floors or upholstery with attachments When using the attachment tools such as the crevice tool round brush or the upholstery brush place the handle of the vacuum in the upright position 1 Turn the quick release cord holder to either side 180 to release the power cord 2 Plug the power coro ne He electrical outlet roast 3 Push the On Off button to the On position to turn the vacuum on 4 Torelease the handle step on the power head and pull the handle back 5 When using the attachments the vacuum must be in the upright position Fig 3 OPERATING INSTRUCTIONS 6 Remove the belt cover Fig 22 1 7 Lift the right side of the brush bar first and then lift the left hand side Fig 22 2 3 8 Remove the brush bar from the power head Fig 22 4 9 Carefully remove any belt residue that may exist in the belt area before replacing with a new belt 10 Remove the worn or broken belt from the motor drive shaft
16. uble shooting checks Occasionally the power nozzle drive belt will require changing the frequency will depend upon the amount of use your vacuum sees 1 Turn the vacuum Off and unplug from power supply 2 Turn the vacuum upside down on a flat level surface 3 Using a Philips screw driver remove the four 4 screws that attach the base plate to the lower plate Fig 19 4 After you have removed the base plate remove the remaining five 5 screws from the lower plate using a Philips screw driver Fig 20 Base Plate 5 With the unit still lying down turn the unit over and lift the power head cover starting from the back of the power head Fig 21 Removing amp Emptying Dust Cup Warning To reduce the risk of electric shock the power cord must be disconnected before removing the dust cup dust cup filter changing the filters or performing maintenance trouble shooting Carpet Height Selector This upright vacuum can be used on multiple types of carpeting bare floors or upholstery with attachments To select a pile height setting 1 Turn vacuum cleaner Off hecks 2 Selecta pile height setting by sliding the carpet height selector The Dust Cup must always be emptied line on the dust cup To remove the dust cup from the vacuum 1 Press down on the dust cup release button that is located on the handle of the dust cup Fig 6 2 Holding the dust cup from the E handle pull th
17. up filter before each use and during prolonged usage Never over fill the dust cup remove dirt and clean the HEPA dust cup filter each time the dust cup is emptied during prolonged usage or risk motor damage Cleaning the HEPA Filter Frame 1 Before replacing the HEPA filter in the HEPA Filter frame you can should rinse the frame in lukewarm water by just running it under the tap to remove any dust that is adhering to the frame Fig 13 Do NOT place in dishwasher pees Fig 13 2 Make sure that the filter frame is completely dry before replacing into the dust cup Always air dry Cleaning the Filter Ring Around the HEPA filter there is a filter ring This is washable in lukewarm water Fig 14 To remove the filter ring slide it off the HEPA filter 2 We recommend washing the filter ring when you are washing your HEPA filter Always allow the filter ring to air dry for 24 hours before replacing onto the HEPA filter Never run the vacuum without all the filters in place Note This is a washable filter but we recommend replacing it every three 3 months Fig 14 lukewarm water Fig 15 We recommend washing it when you are L washing your HEPA filter 11 Always allow the secondary v filter to air dry for 24 hours before replacing into the 3 Ga O vacuum Never run My the vacuum without ae the secondary filter in place Fig 15 Changing amp Cleaning the Pre
18. ust particles and performance of the filter E pa Fig 16 TR airborne allergens from re entering the air Warning Always empty the dust cup This is washable in SL if Pre Motor you breathe In fact it stops 99 97 of all particles as small as 0 3 microns many times smaller than a human hair Because of this incredible filtration performance the HEPA Dust Cup Filter will quickly accumulate many fine dust particles inside the white filter folds that are difficult to see but which will eventually block or reduce your suction power Clean the HEPA Filter after each use as described in this section 1 To remove the HEPA filter remove the dust cup from the unit To remove the dust cup cover hold the cover by the handle turn counter clockwise and lift the cover off Fig 9 Remove the HEPA Rinseable Tap Clean filter from the dust cup Fig 10 Remove the filter ring that is around the HEPA filter Vigorously TapClean the HEPA dust cup filter on a hard surface until no more dust is observed Fig 9 falling out Fig 11 The HEPA filter may also be washed by running it under the tap gt allowing the water e _ 5 to run on the dirty side Er Fig 12 We recommend in o washing it once a month or when suction appears Dl ead reduced Always allow 24 hours for air drying before Sp replacing into the vacuum Fig 10 if not cleaned properly and clean the HEPA dust c
Download Pdf Manuals
Related Search