Envision Peripherals EN-7100e Computer Monitor User Manual
Contents
1. The power cord supplied with your monitor can only be connected to a grounded electrical wall socket or power strip If you wish to connect your monitor to a power supply using the power input socket on the back of your computer you must purchase a power cord with CEE 22 terminated connectors see illustration above EN 7100e Follow these steps 1 Connect the built in video cable into the 15 pin connector on the back of your computer and tighten the two screws 2 Connect the power cord into the power adaptor 3 Plug the other end of the power cord into the power output socket on your PC 4 Connect the power adaptor into the DC IN socket on the back of the monitor 31MY02 Envision Before You Operate the Monitor _ EN 7100e Preparing to Install An Optional Wall Mounting Arm Not supplied This monitor can be attached to a wall mounting arm you purchase separately Disconnect power before this procedure Follow these steps 1 Pull the screw covers off the back of the monitor 2 Support the base and remove the screws EN 7100e 3 Unhook the cable into the monitor Remove the base 4 Remove the back cover from the panel 5 Follow the manufacturer s instructions to assemble the wall mounting arm See next page for further installation instructions 31MY02 Envision Before You Operate the Monitor _ EN 7100e Install An Optional Wall Mounting Arm2. Unsupported mode try different video card setting e Your computer s resolution is out of VESA specifications Right click on the desktop and choose Properties Click the Settings tab then set your computer s display mode to one of the settings listed in the resolution chart below Resolution Chart Resolution Vertical Resolution Vertical in pixels Frequency in pixels Frequency 640 x 480 60 Hz 800 x 600 72 2 Hz 640 x 400 70 Hz 800 x 600 75 Hz 640 x 350 70 Hz 832 x 624 74 5 Hz 720 x 400 70 Hz 1024 x 768 60 Hz 640 x 480 72 8 Hz 1024 x 768 70 Hz 640 x 480 75 Hz 1024 x 768 75 Hz 640 x 480 66 67 Hz 1024 x 768 74 92 Hz 800 x 600 56 3 Hz 1280 x 1024 60 Hz 800 x 600 60 3 Hz 1280 x 1024 75 Hz EN 7100e 16 31MY02 Envision Appendix EN 7100e Specifications Plug amp Play VESA DDC1 LCD Driving TFT Color LCD ARIM Panel system Size 17 0 43 2 cm Input Connector D Sub 15 pin Diagonal Input Video Signal Analog 0 7 Vpp standard Pixel pitch 0 264 mm H x TI OAM PESIIN 0 264 mm V Maximum Screen Size Horizontal Viewable 120 H 100 V 13 3 337 92 mm angle Vertical 10 6 270 34 mm Input Response 50 milliseconds time P 100 264 VA Video Red Green Blue datzate Bee SG Analog Interface Separate SARRA Environmental Operating Temp Sync Considerations 32 to 104 F H Frequency 30 kHz 80 kHz 0 to
3. EN 7100e Limited 3 Year Warranty EN 7100e e Excessive or inadequate heating or air conditioning or electrical power failures surges or other irregularities This three year limited warranty does not cover any of the product s firmware or hardware that you or any third party have modified or altered you bear the sole responsibility and liability for any such modification or alteration All express and implied warranties for the product including the warranties of merchantability and fitness for a particular purpose are limited in duration to a period of three 3 years for parts and labor from the original date of consumer purchase No warranties either expressed or implied apply after this period In the United States some states do not allow limitations on how long an implied warranty lasts Therefore the above limitations may not apply to you EPI s obligations and your remedies hereunder are solely and exclusively as stated here EPI s liability whether based on contract tort warranty strict liability or other theory shall not exceed the price of the individual unit whose defect or damage is the basis of the claim In no event shall EPI be liable for any loss of profits loss of use or facilities or equipment or other indirect incidental or consequential damage In the United States some states do not allow the exclusion or limitation of incidental or consequential damages Therefore the above limitations may
4. 1024 64 00 kHz 60 Hz 1280 x 1024 80 00 kHz 75 Hz EN 7100e 19 31MY02 Envision Appendix EN 7100e Connector Pin Assignment Pin Number Description Pin Number Description 1 Red 9 5V 2 Green 10 Detect Cable 3 Blue 11 NG 4 Ground 12 DDC Serial Data 5 Ground 13 H Sync 6 R Ground 14 V Sync 7 G Ground 15 DDC Serial Clock 8 B Ground 15 Pin Color Display Signal Cable EN 7100e 20 31MY02 Envision This is a warranty statement for Envision color monitors including those sold within North America as specified Envision Peripherals Inc EPI warrants this product to be free from defects in material and workmanship for a period of three 3 years after the original date of consumer purchase During this period EPI will at its option either repair the defective product with new or rebuilt parts or replace it with a new or rebuilt product at no charge except as stated below The parts or product that are replaced become the property of EPI This limited warranty does not cover any losses or damages that occur as a result of Shipping or improper installation or maintenance e Misuse e Neglect Any cause other than ordinary commercial or industrial application e Adjustment by non authorized source e Repair modification or installation of options or parts by anyone other than an EPI Authorized Service Center e Improper environment
5. Not supplied Follow these steps to finish installing the wall mounting arm 1 Place the wall mounting arm onto the back of the monitor Line up the holes of the arm with the holes in the back of the monitor 2 Insert the 4 screws into the holes and tighten 3 Insert the power cable into the slot on the back of the monitor EN 7100e Envision s Model EN 7100e is compatible with the Ergotron line of mounting and arm solutions Contact Ergotron at 800 888 8458 or visit their web site at www ergotron com for more information on the many ways on which you can mount your Envision LCD monitor 31MY02 Envision Before You Operate the Monitor _ EN 7100e Adjusting the Viewing Angle For optimal viewing adjust the monitor s angle to your own preference e Hold the stand firmly when you change the monitor s angle e You can adjust the monitor s angle from 5 to 30 e Do not touch the LCD screen when you change the angle It may cause damage or breakage Be careful to avoid pinching your hand in the swivel base EN 7100e How to Install INF amp ICM File 1 Insert the Windows 95 98 2000 ME XP INF Driver Disk into your floppy drive 2 Follow the Add New Hardware Wizard instructions on the screen 3 If the wizard asks for the location of the driver file select drive A and press Next 10 31MY02 Envision Operating Instructions EN 7100e Front Panel Buttons AUTO MENU d Auto Q
6. Recommended Resolution EPA ENERGY STAR Ergonomic Design Space Saving Compact Case Design EN 7100e Before You Operate the Monitor _ EN 7100e Remove Package Contents The box that your monitor was shipped in should have included the following items 1 Power Adaptor Power Cord Windows 95 98 2000 ME XP INF Driver Disk Quick Start Guide Booklet Containing Warranty amp Safety oak WP EN 7100e LCD Monitor Information 31MY02 Envision Before You Operate the Monitor EN 7100e Connecting the Wires Using the Power Cord Supplied Connect the built in video cable into the 15 pin connector on the back of your computer and tighten the two screws Connect the power cord into the power adaptor Plug the other end of the power cord into a grounded AC outlet or UL approved power strip Connect the power adaptor into the DC IN socket on the back of the monitor EN 7100e Caution Make sure the power cord is the correct type that is required in your area This LCD monitor has a universal power supply that allows operation in either 100 120V AC or 220 240V AC voltage areas no user adjustment is required If the AC outlet is not grounded with three holes install the proper grounding adapter not supplied 31MY02 Envision Before You Operate the Monitor EN 7100e Connecting the Wires Using An Optional Power Cord Not Supplied
7. warranty statements 2002 Envision Peripherals Inc 22 31MY02
8. 40 C V Frequency 55 75 Hz Storage Temp 14 to 122 F Display Colors 16 7 million colors Dot Clock 135 MHz Maximum Resolution 1280 x 1024 pixels EN 7100e 10 to 50 C Operating Humidity 20 to 90 Weight 12 1 Ibs 5 5 Kg 17 31MY02 Envision Appendix Specifications continued Front Panel Buttons Auto Brightness Contrast Power Switch MENU Exit External Functions Controls Contrast Brightness Focus Clock H Position V Position Auto Center Language Dos mode Resolution Selected 6500 K 7800 K RGB Color temp Recall Exit EPA ENERGY STAR Yes Power Consumption Maximum 45 Watts Regulatory Compliance UL CSA FCC TUV GS CE EN 7100e EN 7100e Optimal Viewing Mode 1280 x 1024 75 Hz 16 6 in 422mm 17 7 in 449 mm dE 8 5 Ge 215mm N 12 1 Ibs 5 5 Kg 18 31MY02 Envision Appendix EN 7100e Factory Preset Timing Table landara d Sekeko Zek DOS Mode 600 x 400 31 47 kHz 70 Hz 720 x 400 31 47 kHz 70 Hz VGA 640 x 480 31 47 kHz 60 Hz 640 x 480 35 00 kHz 66 6 Hz 640 x 480 37 50 kHz 75 Hz SVGA 800 x 600 37 879 kHz 60 Hz 800 x 600 46 875 kHz 75 Hz 832 x 624 49 725 kHz 75 Hz XGA 1024 x 768 48 363 kHz 60 Hz 1024 x 768 56 476 kHz 70 Hz 1024 x 768 60 02 kHz 75 Hz 1024 x 768 60 241 kHz 74 9 Hz SXGA 1280 x
9. Envision EN 7100e EN 7100e 17 inch TFT LCD Monitor User s Manual by Envision Peripherals Inc www ENVISIONmonitor com Before operating your monitor please read this manual thoroughly Env s on EN 7100e TBC 6332 1 31MY02 Envision FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help EN 7100e For Your Safety EN 7100e Notice 1 The changes or modifications not expressly appr
10. Never attempt to replace it by yourself EN 7100e For Your Safety EN 7100e General Notes Do not install the monitor near heat sources such as radiators or air ducts Do not place monitor in direct sunlight or in areas with excessive dust mechanical vibration or shock e Save the original shipping carton and packing materials in case you need to ship your monitor Be sure to repackage your monitor as it was originally packed at the factory e Periodically clean your monitor with a soft cloth Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution Never use strong solvents such as thinners benzene or abrasive cleaners since these will damage the cabinet Always unplug the monitor before cleaning it Using the Right Power Cord The supplied power cord is a NEMA 5 15 style plug It is UL listed and CSA labeled for 125 volts AC If the monitor will be connected to your computers power outlet use a minimum No 18 AWG type SJT or SVT three conductors cord with one end terminating with a male grounded plug rated 10A 250V CEE 22 The other end must terminate with a molded on type connector body rated 10A 250V having standard CEE 22 female configuration 31MY02 Envision Installing amp Removing the Base E Install Jenny General Features 17 43 2cm TFT Color LCD Monitor Crisp Clear Display for Windows 1280 X 1024 pixels 75Hz Maximum amp
11. ZN O Power Button u Power Indicator H 60KHz 9 E Brightness RQ Menu Contrast GQ B Contrast OSD Window Power Indicator A green light indicates gt c J O Auto Press this button to automatically set the H Position V Position Clock and Focus that the monitor is on An orange light settings indicates that the monitor is in Off mode Brightness Press this button to adjust the d Power Press this button to turn the picture s brightness If the OSD window is monitor on or off The power indicator will open this button allows you to move within light up the window and select desired functions Contrast Press this button to adjust the picture s contrast If the OSD window is MENU button to open the OSD window the window and select desired functions See next page MENU Press this button to open the OSD window or exit from the OSD window On screen Display OSD Press the O O EN 7100e 11 31MY02 Envision Adjusting the OSD Settings Brightness Focus Adjusts the picture s Contrast brightness Adjusts the picture s contrast Red Operating Instructions EN 7100e Adjusts focus pixel clock signal Clock Adjusts clock pixel frequency H Position Adjusts the horizontal Adjusts the intensity of red o E m Green Contrast Adjusts the intensity o
12. em of its identity and depending on the level of DDC used communicate additional information about its display capabilities The communication channel is defined in two levels DDC1 and DDC2B The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information The DDC2B is a bidirectional data channel based on the I C protocol The host can request EDID information over the DDC2B 13 31MY02 Envision Technical Support FAQ EN 7100e Problem Possible Solution Power LED is not ON e Make sure the power button is ON e Make sure the power adaptor is properly connected to a grounded power outlet and to the monitor No Plug amp Play e Confirm that your computer is Plug amp Play compatible e Confirm that your video card is Plug 8 Play compatible e Inspect the video cable and make sure that none of the pins are bent e Make sure the Envision monitor drivers are installed ENVISION monitor drivers are available at www ENVISIONmonitor com Picture is fuzzy Adjust the Contrast and Brightness settings Picture bounces or a wave pattern is present in the picture e Move electrical devices away from the monitor They may be causing electrical interference Power LED is ON green or orange light is ON but there is no video or picture e Press a key on the keyboard or wiggle the mouse to re activate the monitor e Make sure the video cable
13. f green 70 Blue Adjusts the RJ 65 intensity of blue Exit Saves changes and OSD disappears Reset Clears the current configuration and reapplies auto configuration 1 Press the MENU button to open the OSD window 2 Press the lt or gt buttons until the desired function is highlighted 3 Press MENU to open the function s window 4 Press the lt or gt buttons to change the settings of the function EN 7100e 12 Color Temp Adjusts the color temperature to 7800 K x 0 296 y 0 311 Color Temp Adjusts the color temperature to 6500 K x 0 313 y 0 329 position of the picture V Position Adjusts the vertical position of the picture Auto Center Automatically Language centers picture Adjusts the language selection DOS mode selected DOS mode resolution selection for 720x400 Q70Hz and 640x400 70Hz see next page for details 5 To save and exit highlight the EXIT icon and press MENU or leave the monitor alone for 10 seconds If you want to adjust any other function repeat steps 2 4 Note When the OSD window is open the input signal timing settings appear at the top H stands for horizontal frequency and V stands for vertical frequency 31MY02 Envision DOS mode This feature allows you to choose between resolutions of 720 x 400 or 640 x 400 while working in DOS mode Follow the instructions for selecting functions in the OSD window as listed on the previ
14. inance of the light has been reduced to half of its original value Please send the monitor to an authorized service agent for service Horizontal or vertical disturbances on the screen Adjust the CLOCK and FOCUS settings or press the AUTO button to automatically re configure the monitor s settings Use Win 95 98 shut down mode CLOCK pixel frequency controls the number of pixels scanned by one horizontal sweep If the frequency is not correct the screen shows vertical stripes and the picture s width is incorrect FOCUS adjusts the phase of the pixel clock signal With a wrong phase adjustment the picture has horizontal disturbances with very light screen images Note For FOCUS and CLOCK adjustment use dot pattern or Win 95 98 shut down mode pattern Error Message Possible Solution Cable not connected e Make sure the video cable is properly connected to the computer If the connector is loose tighten the connector s two screws e Inspect the video cable and make sure that none of the pins are bent EN 7100e 15 31MY02 Envision Technical Support FAQ EN 7100e Error Message Possible Solution Input not supported e Your computer has been set to an incompatible display mode Right click on the desktop and choose Properties Click the Settings tab then set your computer s display mode to one of the settings listed in the resolution chart below
15. is properly connected to the computer e Inspect the video cable and make sure none of the pins are bent e Make sure your computer is operating correctly by pressing the CAPS LOCK key and observing whether the CAPS LOCK light turns ON or OFF Missing one of the primary colors RED GREEN or BLUE e Inspect the video cable and make sure that none of the pins are bent e Make sure the video cable is properly connected to the computer Dead Pixel Criteria In order to provide the highest performing products EPI has set the following limits as to the maximum allowable number of bad pixels 4 Bright Sub pixels or 4 Dark Sub pixels or combination of 6 Dark amp Bright The panel used on this product has a total of 3 932 160 sub pixels So even the maximum allowed of 6 bad sub pixels would only amount to a very small 0 00015 of the total sub pixels EN 7100e 14 31MY02 Envision Technical Support FAQ EN 7100e Problem Possible Solution Screen image is not centered or sized properly Adjust the CLOCK and FOCUS settings or press the AUTO button to automatically re configure the monitor s settings Picture has color defects white does not look white e Adjust the settings for Red Green and or Blue colors or select a different color temperature 65 6500 K or 78 7800 K Poor brightness or contrast e The life time of the back light is limited After 20 000 hours the lum
16. ng be sure these openings are not blocked or covered Do not place the monitor on a bed sofa rug or similar surface Do not place the monitor near or overa radiator or heat register Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided The monitor should be operated only with the type of power source indicated on the label If you are not sure of the type of power supplied to your home consult your dealer or local power company Do not overload power strips and extension cords Overloading can result in fire or electric shock For use only with power adaptor manufactured by CHI SAM ELECTRONIC model CH 1205 EN 7100e Precautions EN 7100e The monitor is equipped with a three pronged grounded plug a plug with a third grounding pin As a safety feature this plug will only fit into a grounded power outlet If your outlet does not accommodate the three wire plug have an electrician install the correct outlet or use an adapter to ground the appliance safely Do not defeat the safety purpose of the grounded plug Unplug the unit during a lightning storm or when it will not be used for long periods of time This will protect the monitor from damage due to power surges Never push any object into the slot on the monitor cabinet It could short circuit parts causing a fire or electric shock Never spill liquids on the monitor Do not attempt to service the monitor yourself opening
17. not apply to you 31MY02 Envision Although this limited warranty gives you specific legal rights you may have other rights which may vary from state to state In the United States of America this limited warranty is only valid for products purchased in the Continental United States Alaska and Hawaii Outside the United States this limited warranty is only valid for products purchased in Canada In the United States to obtain service under this limited warranty 1 Call EPI s Customer Service RMA Department at the toll free number 888 838 6388 for the nearest Authorized Service Center located in your area 2 Ask for a Return Merchandise Authorization RMA number 3 Deliver the product freight pre paid to the EPI Authorized Service Center If you cannot deliver the product in person e Pack it in its original shipping container or equivalent e Put the RMA number on the shipping carton e Insure it or assume the risk of loss damage during shipment e Pay one way shipping charge EN 7100e Warranty continued EN 7100e EPI is not responsible for damage to inbound products that were not properly packaged EPI will pay the return shipment charges within one of the countries specified within this warranty statement EPI is not responsible for any costs associated with the transportation of products across international borders This includes the international borders of the countries within this
18. or removing covers can expose you to dangerous voltage and other hazards Please refer all servicing to qualified service personnel To ensure satisfactory operation use the monitor only with UL listed computers which have appropriately configured receptacles marked between 100 240 V AC Min 5A The wall socket should be installed near the equipment and should be easily accessible Disconnect the power cord to stop the power supply to the monitor 31MY02 Envision Special Notes on LCD Monitors The following symptoms are normal with an LCD monitor and do not indicate a problem Due to the nature of the fluorescent light the screen may flicker during initial use Turn off the Power Switch and then turn it on again to make sure the flicker disappears e You may find slightly uneven brightness on the screen depending on the desktop pattern you use e The LCD screen has effective pixels of 99 99 or more It may include blemishes of 0 01 or less such as a missing pixel or a pixel lit all of the time Due to the nature of the LCD screen an after image of the previous screen may remain after switching from an image that has been displayed for hours This after image could require several hours to disappear The life of the fluorescent light used in the LCD monitor is approximately 20 000 hours Contact your dealer or EPI service center for replacement when the screen is dark flickering or not lighting up
19. ous page Press your monitor s Power button off and then on to activate your chosen DOS mode resolution Note the default DOS mode resolution is 720x400 70Hz How to Optimize the DOS mode 1 Insert the Windows 95 98 2000 ME INF Driver Disk into your floppy drive 2 Open Windows Explorer to search on the floppy drive Drive A to find the Dos1 exe file 3 Double click on the Dos1 exe file 4 Expand the picture to full screen by pressing the icon on the top of window If there is no icon the picture is already at full screen If you don t have the driver disk 1 Choose Start Programs MS DOS mode 2 Type C gt EDIT and press Enter You will be in the Dos Editor screen 3 Press the AUTO button on the front of your monitor for 2 seconds The screen will be automatically adjusted If the screen is distorted for example the picture can t go to full screen the background of white EN 7100e Operating Instructions EN 7100e pattern has vertical stripe noise or the characters are twisted 1 Change the resolution to 640 x 400 2 Press the Power button off and then on 3 Press the AUTO button for 2 seconds Note the above procedure must process in full screen pattern To exit press the ESC key or press ALT F and then press the X key Plug 8 Play DDC1 2B Feature This monitor is equipped with VESA DDC1 2B capabilities according to the VESA DDC STANDARD It allows the monitor to inform the host syst
20. oved by the party responsible for compliance could void the user s authority to operate the equipment 2 Shielded interface cables and AC power cord if any must be used in order to comply with the emission limits 3 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment It is the responsibility of the user to correct such interference As an ENERGY STAR Partner Envision Peripherals Inc has determined that this product meets the ENERGY STAR guidelines for energy efficiency Warning To prevent fire or shock hazard do not expose the monitor to rain or moisture Dangerously high voltage is present inside the monitor Do not open the cabinet Refer servicing to qualified personnel only 31MY02 Envision Do not use the monitor near water e g neara bathtub washbow l kitchen sink laundry tub swimming pool or in a wet basement Do not place the monitor on an unstable cart stand or table If the monitor falls it can injure a person and cause serious damage to the appliance Use only a cart or stand recommended by the manufacturer or sold with the monitor If you mount the monitor on a wall or shelf use a mounting kit approved by the manufacturer and follow the kit instructions Slots and openings in the back and bottom of the cabinet are provided for ventilation To ensure reliable operation of the monitor and to protect it from overheati
Download Pdf Manuals
Related Search