Envision Peripherals EFT920 Computer Monitor User Manual
Contents
1. 920 SOMFTHING TO SFF EFT920 19 inch Flat CRT Color Monitor User s Manual by Envision Peripherals Inc www ENVISIONmonitor com Before operating your monitor please read this ENVISION Aerem SOMETHING TO SEE 1 v1 031004 ENVISION SOMETHING TO SEE FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help EFT920 For Your Safety EFT920 Notice 1 The changes or modi2. page v1 031004 ENVISION SOMETHING TO SEE Technical Support FAQ EFT920 Problem Possible Solution Power LED is not ON Make sure the power button is ON Make sure the power cord is properly connected to a grounded power outlet and to the monitor No Plug amp Play Confirm that your computer is Plug amp Play compatible Confirm that your video card is Plug amp Play compatible Inspect the video cable and make sure that none of the pins are bent Make sure the Envision monitor drivers are installed ENVISION monitor drivers are available at www ENVISIONmonitor com Picture is fuzzy Adjust the Contrast and Brightness settings Picture bounces or a wave pattern is present in the picture Move electrical devices away from the monitor They may be causing electrical interference Power LED is ON green or orange light is ON but there is no video or picture Press a key on the keyboard or wiggle the mouse to re activate the monitor Make sure the video cable is properly connected to the computer Inspect the video cable and make sure none of the pins are bent Make sure your computer is operating correctly by pressing the CAPS LOCK key and observing whether the CAPS LOCK light turns ON or OFF Missing one of the primary colors RED GREEN or BLUE Inspect the video cable and make sure that none of the pins are bent Make sure the video cable is
3. properly connected to the computer Screen image is not centered or sized properly Adjust the Horizontal Vertical or Zoom settings in the OSD window Picture has color defects white does not look white Adjust the User Color setting in the OSD window EFT920 10 v1 031004 SOMETHING TO SEE EP Appendix EFT920 Specifications CRT Size 19 0 48 3 cm Input Video Red Green Blue Analog Interface TEST DOOR Separate H V TTL 0 25mm D Sync 0 21mm H dot pitch HN Sync Positive Negative FH H Frequency 30 kHz 98 kHz 90 degree deflection V Frequency 50 Hz 160 Hz Viewable image size 18 0 45 3 cm Input Video Signal Analog diagonal 0 7 Vpp 75 OHM Positive Preset Display area 13 7 346 mm X 10 3 260 mm Power Source Universal AC lt 100 240 V Dot Clock 200 MHz 50 60 Hz Factory Preset Mode 8 Maximum Resolution 1600 x 1200 pixels User Programmable Mode 20 Plug amp Play VESA DDC1 2B TM EPA ENERGY STARG Yes Power Consumption 130 Watts Maximum Regulatory UL CSA FDA Compliance FCC TUV GS MPRII EFT920 11 v1_031004 ENVISION SOMETHING TO SEE Specifications continued Appendix Environmental Considerations Operating Temp 32 to 104 F 0 to 40 C ambient g Operating Humidity 1096 to 8596 18 2in 17 6 in 44 0 lbs 463 mm 446 mm 20 0 Kg
4. Signal Cable Attached Mini D sub 15 Male Optimal Viewing Mode 1280 x 1024 85 Hz EFT920 12 EFT920 Optimal Viewing Mode 1280 x 1024 85 Hz v1 031004 Appendix EFT920 Factory Preset Timing Table Standard Resolution Horizontal Vertical in pixels Frequency Frequency VGA 720 x 400 31 5 kHz 70 Hz 640 x 480 31 5 kHz 60 Hz VESA 85 640 x 480 43 3 kHz 85 Hz 800 x 600 53 7 kHz 85 Hz 1024 x 768 68 7 kHz 85 Hz 1280 x 960 85 9 kHz 85 Hz 1280 x 1024 91 1 kHz 85 Hz VESA 75 1600 x 1200 93 8 kHz 75Hz EFT920 13 v1 031004 ENVISION Mice Appendix EFT920 Connector Pin Assignment Pin Number Description Pin Number Description 1 Red 9 NC 2 Green 10 Ground 3 Blue 11 Monitor Ground 4 Ground 12 DDC Serial Data 5 Ground 13 H Sync 6 R Ground 14 V Sync 7 G Ground 15 DDC Serial Clock 8 B Ground EFT920 15 Pin Color Display Signal Cable 14 v1 031004
5. con or leave the monitor alone for 10 seconds If you want to adjust any other function repeat steps 2 4 Note When the OSD window is open the input signal timing settings appear at the top H stands for horizontal frequency and V stands for vertical frequency v1 031004 ENVISION SOMETHING TO SEE Plug amp Play DDC1 2B Feature This monitor is equipped with VESA DDC1 2B capabilities according to the VESA DDC STANDARD It allows the monitor to inform the host system of its identity and depending on the level of DDC used communicate additional information about its display capabilities The communication channel is defined in two levels DDC1 and DDC2B The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information The DDC2B is a bidirectional data channel based on the protocol The host can request EDID information over the DDC2B EFT920 Operating Instructions EFT920 Windows INF Driver File Most computers will automatically configure your monitor to work with your computer For optimal viewing of your monitor download the Envision monitor driver Follow these steps 1 Go to www ENVISIONmonitor com 2 Click on SERVICES amp SUPPORT to open the drivers web page 3 Follow the directions on the web page to download and install the driver on your computer Or go to www ENVISIONmonitor com support drivers asp to directly access the driver web
6. fications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 2 Shielded interface cables and AC power cord if any must be used in order to comply with the emission limits 3 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment It is the responsibility of the user to correct such interference As an ENERGY STAR Partner Envision Peripherals Inc has determined that this product meets the ENERGY STAR guidelines for energy efficiency Warning To prevent fire or shock hazard do not expose the monitor to rain or moisture Dangerously high voltage is present inside the monitor Do not open the cabinet Refer servicing to qualified personnel only v1_031004 ENVISION SOMETHING TO SEE Precautions Do not use the monitor near water e g near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement Do not place the monitor on an unstable cart stand or table If the monitor falls it can injure a person and cause serious damage to the appliance Use only a cart or stand recommended by the manufacturer or sold with the monitor If you mount the monitor on a wall or shelf use a mounting kit approved by the manufacturer and follow the kit instructions Slots and openings in the back and bottom of the cabinet are provided for ventilation To ensure rel
7. iable operation of the monitor and to protect it from overheating be sure these openings are not blocked or covered Do not place the monitor on a bed sofa rug or similar surface Do not place the monitor near or over a radiator or heat register Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided The monitor should be operated only with the type of power source indicated on the label If you are not sure of the type of power supplied to your home consult your dealer or local power company Disconnect the power cord to stop the power supply to the monitor EFT920 For Your Safety EFT920 The monitor is equipped with a three pronged grounded plug a plug with a third grounding pin As a safety feature this plug will only fit into a grounded power outlet If your outlet does not accommodate the three wire plug have an electrician install the correct outlet or use an adapter to ground the appliance safely Do not defeat the safety purpose of the grounded plug Unplug the unit during a lightning storm or when it will not be used for long periods of time This will protect the monitor from damage due to power surges Do not overload power strips and extension cords Overloading can result in fire or electric shock Never push any object into the slot on the monitor cabinet It could short circuit parts causing a fire or electric shock Never spill liquids on the monitor Do not a
8. ith a male grounded plug rated 10A 250V CEE 22 The other end must terminate with a molded on type connector body rated 10A 250V having standard CEE 22 female configuration EFT920 For Your Safety EFT920 General Features e 19 48 3 cm Color Monitor Crisp Clear Display for Windows Supports Resolutions up to 1600 X 1200 pixels 75Hz EPA ENERGY STAR Package Contents The box that your monitor was shipped in should have included the following items 1 EFT920 Color Monitor 2 Power Cord 3 Quick Start Guide 4 Booklet containing Warranty and Safety information v1 031004 Before You Operate the Monitor EFT920 SOMETHING TO SEE Installing amp Removing the Base EFT920 5 v1_031004 SOMETHING TO SEE ce Before You Operate the Monitor Errez0 Connecting the Wires Using the Power Cord Supplied 1 Connect the built in video cable into the 15 pin connector on the back of your computer and tighten the two screws 2 Connect the power cord into your monitor s power input socket 3 Plug the other end of the power cord into a grounded AC outlet or UL approved power strip EFT920 Caution Make sure the power cord is the correct type that is required in your area This monitor has a universal power supply that allows operation in either 100 120V AC or 220 240V AC voltage areas no user adjustment is required If the AC outlet is not grounded wi
9. lue Adjusts the Red Blue Gain controls to obtain optimum whiteness level Pincushion 9300 Color Temp Brightness Adjusts the picture until the edges Adjusts the color temperature Adjusts the picture s brightness neither bulge out nor pull in to 9300 K x 0 283 y 0 297 o H Center Trapezoid Degauss Adjusts the horizontal position Adjusts the top and bottom of the Adjusts color impurity caused of the picture picture until the sides are parallel by monitor movement or magnetic field build up inside the monitor B H Size q Pin Balance Adjusts the horizontal size of Adjusts to compensate for the N Moire Reduce the picture pincushion unbalance Reduces interference that appears as ripples or wave patterns V Center Ted Parallelogram Adjusts the vertical position of Shifts the top and bottom of the Recall the picture picture left or right until the sides Restores the monitor to are vertical factory settings 0 V Size Adjusts the vertical size of the Rotation Exit picture Rotates the entire picture Saves changes and closes the OSD window 6500 Color Temp Adjusts the color temperature to 6500 K 0 313 y 0 329 Press the MENU button to open the OSD window Press the or buttons until the desired function is highlighted 3 Press MENU to open the function s window Press the or buttons to change the settings of the function EFT920 5 To save and exit press the EXIT i
10. th three holes install the proper grounding adapter not supplied v1 031004 ENVISION Operating Instructions EFT920 SOMETHING TO SEE Front Panel Buttons Exit Brightness Contrast Power Button Power Indicator Q Exit Press this button to save changes and er Close the OSD window Brightness Press this button to adjust the picture s brightness If the OSD window is open this button allows you to move within the window and select desired functions E Contrast Press this button to adjust the picture s contrast If the OSD window is open this button allows you to move within the window and select desired functions EFT920 see 5 M MENU Press this button to open the OSD window or select a highlighted function Power Indicator A green light indicates that the monitor is on An orange light indicates that the monitor is in Off mode Power Press this button to turn the monitor on or off The power indicator will light up On screen Display OSD Press the MENU button to open the OSD window and adjust settings on your monitor See next page v1 031004 ENVISION SOMETHING TO SEE Adjusting the OSD Settings 9 80 Language Zoom Adjusts the language selection Contrast Adjusts the picture s contrast simultaneously Operating Instructions Adjusts the vertical and horizontal size of the picture EFT920 User Color Red B
11. ttempt to service the monitor yourself opening or removing covers can expose you to dangerous voltage and other hazards Please refer all servicing to qualified service personnel To ensure satisfactory operation use the monitor only with UL listed computers which have appropriately configured receptacles marked between 100 240 V AC Min 3 5A The wall socket should be installed near the equipment and should be easily accessible v1_031004 ENVISION SOMETHING TO SEE General Notes Do not install the monitor near heat sources such as radiators or air ducts Do not place monitor in direct sunlight or in areas with excessive dust mechanical vibration or shock Save the original shipping carton and packing materials in case you need to ship your monitor Be sure to repackage your monitor as it was originally packed at the factory Periodically clean your monitor with a soft cloth Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution Never use strong solvents such as thinners benzene or abrasive cleaners since these will damage the cabinet Always unplug the monitor before cleaning it Using the Right Power Cord The supplied power cord is a NEMA 5 15 style plug It is UL listed and CSA labeled for 125 volts AC If the monitor will be connected to your computer s power outlet use a minimum No 18 AWG type SJT or SVT three conductors cord with one end terminating w
Download Pdf Manuals
Related Search