Home

Enviro EA800 Home Security System User Manual

1. HOME key This key displays the home screen MONITORING when pressed MENU key Displays the MAIN MENU screen when pressed from any menu level or from the home screen E SILENCE key Alarms cannot be cleared and will continue to recur until the moni tored conditions detected by the sensors are within the programmed parameters Pressing the SILENCE key temporarily silences the local audible alarm and deacti vates the auxiliary relay for 10 minutes If a new alarm originating from a different sensor occurs within this 10 minute period the audible alarm and aux relay are reactivated and require another key press to silence the audible alarm D 011 0152 General Information Base Unit Connections Figure 5 shows the EA800 base unit s connections and Table 3 describes the functions of each connection Note The base unit has four wired sensor inputs and four wireless RF sensor inputs Power Aux In Power Out L 004 0520 J2 Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 Figure 5 EA800 Base Unit Connections Table 3 EA800 Base Unit Connector Functions Connector Designation Function USB USB Type A connection used to program firmware export logs and export and import configuration files www winland com lists compatible USB sticks Power In 11 26 VDC input power connection for EA800 base unit from accessory power supply or alarm panel Observe and polarity mar
2. Alarm Log Sensors Data Laa About EASHE b et BZ D l Wiew Alarm Log Wiew Sensor Log 2 UMDKY ROOM OLER 2 OLEE 4 Fao a S Sege 66 13 23 PM m power on i arm A4 BS 2HRS 11 2r 52 FPH Gg el DOLER 3 Alarm Malye TEF High Alarm Cleared MAC Gool CSFeR eee 1 GP Firmware Wersion S BA1 B318 4 2 Last Communication Aq ASAS 16 52 46 PH JE Figure 17 Locked Screen Map 75 The displayed screen is dependent on whether an alarm is active or not D Walk in Cooler H Warehouse Sensors Relays Data Log System About EASGE See Figure 19 R fae Boner i Wiew Sensors Replace RF Sensor Edit Sensor Delete Sensor Fer formance T une Sacer Replace RF Sensor 4783 2008 1 i STi ae PN Edit Sensor Delete Sensor ROUTERI 3 Ferformance Alarm Value Gr B Pause High Alarm Cleared Calusa See Figure 24 et Date Set Time Configuration Change Password Update Firmware EE Confis Figure 18 Unlocked Screen Map Top Level 76 S HET ES Rn Felay Z Relay 3 Relay 4 Relay 3 Gg 7 HET e Felay 5 Felay amp Relay r Relay amp VEER i a HH h319 4 1 land Elec Cc chee ee Electronics Inc 1ghts Reserved Pec al Wersion 1 2 Firmware Wersion S BA1 HS14 1 2 See Figure 23 pt BZ e fi Liew Alarm Log Wiew Sensor Log Export All Logs Clear Alarm Log Clear Sensor Lo Li a D 011 0152 Appendix A Screen Maps
3. Maintenance This chapter contains instructions on performing the following maintenance tasks m Lock unlock the base unit See Locking and Unlocking the EA800 on page 55 Pausing resuming sensor monitoring See Pausing Monitoring and Cancelling Pause on page 56 Adding sensors See Adding a Sensor on page 57 Replacing a sensor See Replacing a Sensor on page 57 Deleting a sensor See Deleting a Sensor on page 59 Reprogramming a Relay See Reprogramming a Relay on page 59 Exporting all logs See Exporting the Stored Logs on page 68 Clear the alarm log See Clearing the Alarm Log on page 64 Clear the sensor log See Clearing the Sensor Log on page 64 Change the current date or time See Changing the Date or Time Setting on page 61 Change date format See Changing the Date Format on page 60 Change time format See Changing the Time Format on page 60 Change data collection frequency See Changing Sensor Data Collection Frequency on page 61 Enabling or disabling the audible alarm buzzer See Changing the Buzzer Setting on page 62 Changing the password See Changing the Password on page 63 Clearing the alarm log file See Clearing the Alarm Log on page 64 Clearing the sensor log file See Clearing the Sensor Log on page 64 Updating the firmware See Updating the Firmware on page 65 Saving the configuration to a USB drive See Saving
4. SN Enter Waluet HHH H Pee tandry Poon H PCAMCER TT CANCEL OPREW OE Sune Pump Kitchen pe Caled HELL Aish Alarm Limit Easement Earn Storage Room M Enter Walue OK ed Ee ane SR R EE a z Computer Room ee ee Wm et SS 5 eee Enter Walue 0030 Or ar led Sh Doce Ha Hlarm Uelay Door 5 Window 1 Lindos Ai Enter Walue Hp Window 3 rr C LHNCEL PREM EAT Figure 20 Add New Sensor Screen Map 78 D 011 0152 Appendix A Screen Maps i i at fi Cooler 1 Cooler 2 Laundry Room Cooler 3 Cooler 4 Screen displayed is dependent on the sensor type Geng Hone H R Geen Le j Hiah Alarm Limit Alarm Delay Time Low Alarm Limit Hysteresis Alarm Delay Time Sensor Hame Enter alue 57 Cooler Si Enter alue H Figure 21 Edit Sensor Screen Map Hae mm e GT a Active Condition 40 ALAR eELHY STH Je Energized arm Uplu Energized Alarm or Warning Set to et to Set tor et toi Energized De Energized Alarm Only Alarm or Warning Figure 22 Relay Screen Map D 011 0152 79 80 R et BZ G fi Liew Alarm Log Wiew Sensor Log Export All Logs Clear Alarm Log Clear Sensor Lo PEACE iy Data Export Complete Are You sure Figure 23 Data Log Screen Map D 011 0152 Appendix A Screen Maps et Uate Set Time Configuration Change Password Update Firmware Load Sane ii Dependent on format eT ime O O O O O VE EYE Enter Hour 1 1 C1
5. ENVIROGALERT A amp S OUO Ulm ENVIROALERT Electronic Multi Zone Environmental Alarm System Installation Owner s Manual CE D 011 0152 Limitations of the Alarm System or Device While your alarm system or device is reliable and sophisticated it does not offer guaranteed protection against burglary fire or other emergency Any security product whether commercial or residential is subject to compromise or failure to warn for a variety of reasons These include Individuals may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device Monitoring devices will not operate without power Devices powered by AC will not work if their AC power supply is off for any reason If system has battery backup batteries that are not maintained can fail to provide the necessary power for devices to function properly Alarm warning devices such as sirens bells and horns may not alert people or awaken sleepers if they are located on the other side of closed or partly closed doors If warning devices are on a different level of the residence from the bedrooms they are less likely to awaken or alert people inside the bedrooms Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service and are subject to compromise by sophisticated means of attack Signals sent by wireless transmitters ma
6. Viewing Active Alarms on page 50 Viewing the Alarm Log on page 51 Viewing Pending Alarm Information on page 51 Viewing Limit Settings on page 52 Viewing the Event Log on page 52 Viewing the Sensor Log on page 53 Viewing Firmware Information on page 53 Viewing RF Information on page 54 Monitoring Environmental Conditions The current environmental conditions measured by each sensor connected to the EA800 base unit are shown on the home screen Depending on the current sensor status the home screen may be one of the following screens m MONITORING screen This screen is shown when there are no active alarms or pending alarms This screen displays the current readings from all programmed sensors as shown in the example below Note Dashes indicate that a sensor has not been programmed yet Current Date Current Time This column shows environmental readings for wired sensors 1 4 This column shows environmental readings for wireless sensors 5 8 Sensor 1 Sensor 5 Sensor 2 Sensor 6 Sensor 3 Sensor 7 not installed Sensor 4 Sensor 8 not installed m MONITORING screen with pending alarm A pending alarm indicates that a sensor has exceeded the low or high limits but that the condition has i not exceeded the programmed delay 0 to 120 minutes When an T alarm is pending the sensor s reading is displayed in reverse text as E Sg shown in the example for wired sensor 2 Oper
7. a Figure 4 EA800 Base Unit Keys Key Functions Function This key s function changes as determined by the software Its current function is displayed immediately above the key on the display This key s function changes as determined by the software Its current function is displayed immediately above the key on the display This key s function changes as determined by the software Its current function is displayed immediately above the key on the display Up Arrow This key provides the scroll up function It moves the selection cursor up a list or increments the value of alphanumeric entry fields as identified by the flash ing cursor The values provided are dependent on the currently active field For example the available selections may be a or sign numbers or alphanumeric characters and special characters Down Arrow This key provides the scroll down function It moves the selection cursor down a list or decrements the value of alohanumeric entry fields as identified by the flashing cursor The values provided are dependent on the currently active field For example the available selections may be a or sign numbers or alpha numeric characters and special characters ENTER key This key accepts the currently entered selection when pressed If the selection is a menu item the selected item is accessed If the current selection is an entered value pressing the ENTER key accepts the entered value
8. 14 e HA III e 4 20mA sensor e Wireless humidity sensor e Wireless temperature sensor D 011 0152 General Information Table 11 Sensor Parameter Descriptions continued Parameter Applicable to Sensors Description High Alarm e Blue Red and White The High Alarm Limit sets the value that trips the high alarm when Limit temperature sensors exceeded e HA III e 4 20mA sensor e Wireless humidity sensor e Wireless temperature sensor Alarm Delay All This sets the time period that an alarm condition can exist before the Time alarm is triggered This is useful for helping to prevent false alarms from occurring in situations where normal activities cause conditions to tem porarily exceed alarm thresholds For example the temperature in a freezer may temporarily rise above the High alarm limit while frozen food is being restocked and the freezer door is open but the delay prevents the alarm from going off unless the temperature fails to cool below the alarm threshold within the alarm delay period Relay Operation This section describes the operation of the base unit s relays The relays must be programmed correctly so that their outputs provide the desired signaling to the alarm panel Table 12 Relay Configuration Settings Relay Setting Description No Alarm No Alarm Power is removed from the relay coil as shown below Relay State ge De Energized default NG alan C S NO panel Idc 0
9. Press the Reset Button on the sensor to restart the search process if necessary After the base unit has identified each wireless sensor and you have programmed it temporarily mount it in its desired location using tape This allows the sensor to be relocated if necessary in order to obtain good signal strength Connecting Wired Temperature Contact Closure and Water Bug Sensors 1 Make certain the sensor s wiring is passed through the opening in the mounting plate 2 Remove the adapter from the correct input connector header by pulling the adapter up and off of the circuit board header connector 3 Strip the ends of each of the sensor s wires as indicated by the gauge on adapter you just removed 4 Insert the stripped wire ends into screw terminals of the adapter as indicated by the EA800 Wiring Diagram you completed in the preparation phase There is no need to observe polarity when connecting sensor wires See Figure 14 J6 Input 1 Input2 Input 3 Input 4 Figure 14 EA800 Base Unit Wired Temperature Contact Closure and Water Bug Sensor Connections 5 Secure the connections using the setscrews on the adapter Check the connection by lightly pulling on each connection 6 After connecting the wire ends to the adapter align the adapter to the correct header pins as indicated by your EA800 Wiring Diagram and press the adapter fully onto the header connector pins 24 D 011 0152 Connecting Wired HA lIl Humidity Senso
10. SE Ata See About ESAS lt gt SSS lias When done reviewing the current Line 1 a sensor readings and return to the Line 2 e LEET 09 57 58 PM SE Blees E 1 Se To return to Active Alarm Line 5 Pr Alarm Walue 71 F or Monitoring screen Line 6 amp _ High Alarm EE Esch To view previous or next alarms The View Alarm Log lines provide the following information m Line 1 Sequence number Identifies the alarm in the log list Line 2 Date and time the alarm was logged Line 3 The relay connected to the sensor that logged the alarm condition Line 4 The name of the sensor that logged the alarm condition Line 5 The sensor s reported value that generated the alarm Line 6 The alarm type or the clearing of alarm type Viewing Pending Alarm Information To view the current readings of a sensor that is in the pending alarm state perform the following procedure Emap teen op d r og KA E Er Els A Sensors Open ME F Pr Open B About EASHE bei ay D 2 Cooler 1 H pts Blue To return to Active Alarm Gs eg E GE STT or Monitoring screen I Cooler 3 l oF B Cooler 4 Ss Delay 3 min 2 a a sn biel D 011 0152 51 Viewing Limit Settings Viewing Limit Settings To view the current readings and the limits of a sensor that is not in an alarm state perform the following procedure VEER G ot o Harn Su KA b ver Ehe 8 mere co ch F e abont EREDE Eag Dr mo SNS R Ka SI
11. Sensors Sensor Parameter Descriptions This section provides a description of each sensor parameter Table 11 Parameter Sensor Name Applicable to Sensors All Sensor Parameter Descriptions Description A name used to identify the sensor in the alarm system Select a name readily identified by the viewer The sensor name is displayed on the Main screen during a no alarm condition and on the Alarm screen during an alarm condition Two name choice types are available e Common Name These are preprogrammed names e Custom Name This selection allows you to enter any name if the preprogrammed common names do not adequately identify the sensor in the system limited to 16 characters Note Duplicate sensor names are not permitted Unit of e Blue Red and White This parameter allows you to choose the unit of measure used for sen Measure temperature sensors sor reading and display e 4 20mA sensor e Blue Red and White temperature sensors C or F e Wireless e 4 20mA sensors the following Common Units of measure are temperature sensors available F Fahrenheit C Centigrade K Kelvin rh percent relative humidity psi pounds per square inch Pa Pascals kPa kiloPascals Ib pound kg kilogram e 4 20mA sensors can also use custom units Enter the appropriate units for the connected 4 20mA sensor via the keypad Resolution 4 20mA sensor This determines the range that may be used for
12. When all sensors have been added you must configure the relays so that the outputs indicate the monitored conditions correctly Perform the following procedure to configure all relays used Note The default relay settings are e Relays 1 8 Active Condition Alarm Only e Aux Relay Active Condition Alarm or Warning e All Relays No Alarm Relay State De Energized If these defaults are acceptable it is not necessary to configure the relays ee olay o Alarm Relay state pee Relay E Active Condition H eee J gt Felay 4 gt G ert Relau 5 About EASE Een A EC a a OZ Energized Sett nergize et ta De Eneraized gt PARCEL oT WE ee ee R O HD HLHEM RELAY STATE e Energize D Energized d Set to a Energized PARCEL oT WE ee ee HIE CONDITION arm Unly Alarm or Warning Set to elb Alarm Only o Hlarm Rela ate GD Active Condifion g ee EI rr ee ee ee jor e E HIE CONDITION arm Unly St Ss D Alarm or Warning H Set toi Alarm or Warning Eain E o F3 Repeat this procedure to configure the next relay OR Return to the Home screen when you have configured all CH relays To create a backup copy of the complete configuration see Saving Configuration Settings on page 66 48 D 011 0152 Operation This chapter provides instructions for doing the following Monitoring Environmental Conditions on page 49 Viewing Sensor Settings on page 50
13. must be retained if using the template available at www winland com Because the files are in CSV format they can be converted to tables in a word processing program or imported into a spreadsheet program Exported Alarm Data The following is an example of exported alarm data 12 27 2007 12 27 2007 12 27 2007 12 27 2007 12 27 2007 12 27 2007 01 28 39 01 29 10 02 38 45 02 39 48 07 10 45 07 10 50 WP A UUW Laundry Room Laundry Room Cooler 3 67 Cooler 3 67 Laundry Room roy Wired WaterBug 1 Wired WaterBug 0 Contact Blue 4 Contact Blue 0 Wired WaterBug 1 Wired WaterBug 0 Wet Dry 58 58 Wet Dry Dry Dry Dry 158 158 Dry Dry F RF F RF Dry Laundry Room Dry Dry The data presented provides the following alarm information Sensor Reading Low High Date and time Sensor Sensor at time of Limit Limit Unit of Sensor Sensor of reading Number Name alarm Value Value Measure Connection Type Code 12 27 2007 Laundry 01 28 39 3 Sain Wet Dry Dry N A Wired WaterBug 1 68 D 011 0152 Maintenance Exported Event Data The following is an example of exported event data 12 24 2007 07 06 03 PM Sensor deleted 1 12 24 2007 07 10 50 PM Sensor added 1 12 25 2007 02 27 14 PM System power on 1 12 25 2007 02 27 50 PM Sensor deleted 1 12 25 2007 02 36 02 PM Sensor added 1 12 25 2007 03 08 55 PM Sensor deleted 1 12 25 2007 03 11 19 PM Sensor added 1 The dat
14. you must program at least 1 connected sensor into the EA800 base unit prior to the end of the 30 minute alarm time out If the alarm buzzer sounds press the Alarm Silence key to temporarily silence the alarm buzzer D 011 0152 27 Programming Accessing the MAIN MENU for Programming 1 iY If not already powered up apply power to the EA800 base unit During the boot process The Winland Electronics splash screen is displayed The system verifies flash memory as indicated by FLASH BOOT at the bottom of the screen The About screen is displayed The MONITORING screen is displayed UNLOCK appears above the F1 soft key Follow the steps below to unlock the keypad and access the MAIN MENU screen pe SEM EE EAR ST Example shown set values as appropriate for your system 69 36 HL UE A LS EMSRS INSTALLED Ey GEEN E og Enter Password PAGG oz Fels Data Log System About EASHE PCHAGEL PREM Mel LUE fT 0800 Note f the password entered was incorrect the INVALID PASSWORD screen is displayed If this happens press the OK soft key F3 to try again The 0800 password is a permanent password that can always be used to unlock the base unit even if a different password has been set Note Because there are no sensors programmed into the EA800 base unit the buzzer will sound when the timer reaches 00 00 seconds Press N to temporarily silence the buzzer You can now access the MAIN MENU programming functions Configuring
15. 0 0 65 F 65 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 12 26 2007 10 20 01 PM 17 C 0 0 0 0 0 0 0 0 69 F 0 0 0 0 0 0 0 0 69 F 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 66 F 255 0 0 0 0 0 0 0 0 65 F 75 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 Each entry is interpreted as 12 26 2007 09 55 00 PM 11 CSVs for Sensor 1 11 CSVs for Sensor 2 11 CSVs for Sensor 3 11 CSVs for Sensor 4 11 CSVs for Sensor 5 11 CSVs for Sensor 6 11 CSVs for Sensor 7 11 CSVs for Sensor 8 There is a line feed and a carriage return character at the end of each The data collected at 09 55 00 in the data log example above provides the sensor information shown below for Sensor 1 The data represented by each of the 11 data fields is defined below and is applicable to each of the 8 sensors that may be connected Sensor 1 CSV2 CSV5 CSV11 Date and time of CSV1 Unit of CSV3 CSV4 Pending CSV6 CSV7 CSV8 CSV9 CSV10 Low reading Reading Measure LO Pause Alarms Low High Comm Fail No Data Battery 12 26 2007 GZzxb EF fee fe eee E Blank The data is null and is not valid for that sensor For example the LQI signal strength position is null for wired sensors but shows the LQI value as shown for the two wireless sensors 255 and 105 respectively Where wireless sensors are not installed the LQI is also blank indicating that no reading is made m O 0 The data is valid and is valid data for that sensor s data point D 011 0152 4
16. 60 minutes 1 year Buzzer e Enable Enabled Enables and disables the buzzer when an alarm limit has e Disable been exceeded or a warning condition exists Selecting Disable for this parameter turns the audible alarm buzzer off completely No audible alarm tone will sound when an alarm occurs if DISABLE is selected RF Channel 2405 MHz channel 16 Selects the ISM band radio frequency RF channel for D 011 0152 2410 MHz 2415 MHz 2420 MHz 2425 MHz 2430 MHz 2435 MHz 2440 MHz 2450 MHz 2455 MHz 2460 MHz 2465 MHz 2470 MHz 2475 MHz 2480 MHz 11 12 13 14 15 16 17 18 19 2445 MHz 20 21 22 23 24 25 26 transmission between the wireless sensors and EA800 base unit Sensors Sensors 10 A variety of sensors may be used with the EA800 base unit to provide environmental status and information These include the following m Wired Sensors Relays 1 through 4 are for use with sensors wired to the base unit Wired sensors can be any of the following types e Low temperature sensors Blue Thermistor Probes e High temperature sensors Red Thermistor Probes e Ultra Low temperature sensors White Thermistor Probes e HA III humidity sensor e Water Bug sensor Supervised e NO Contact e N C Contact e 4 20 mA m Wireless Sensors Relays 5 through 8 are for use with wireless sensors These sensors transmit to the EA800 base unit through RF li
17. D 011 0152 31 Programming Setting the Time Unlock the EA800 to continue programming if necessary See Accessing the MAIN MENU for Programming on page 28 From the MAIN MENU use the arrow keys to select SYSTEM then select Set Time and set the current time as shown below If your region uses Daylight Savings Time and you want the EA800 to display the correct time you must change the time setting manually when Daylight Savings Time starts and ends Note To advance the cursor to the next digit when entering numeric values press the NEXT F3 key To can cel press F1 Use the arrow keys to increase or decrease the numeric value Note The following menus are for setting time in 12 hour format Follow the similar on screen prompts to set time in 24 hour military time format at 8 wmd HT EN Example shown set values as arm Log arm Log appropriate for your system HS et elaus elays Data Log Data Log System H lt k About EASAH SS eS Sa E D et Time 4 Configuration Change Password pa System About EASBHE ae Update Firmware C1 to 12 Hours Load Saue Conti ne PCHALEL PREM HEAT fe ___ PM d Enter Minute 33 B to 59 Minutes ee Time O O O O O OoOO Enter Second 23 CH to 59 Seconds Set tot 11 33 23 Fh You have set the time for the EA800 Proceed to the next section to add wireless sensors If you are not adding wireless sensors skip to Adding Wired Sensors on page 43 32 D
18. From EA800 logic coal Alarm Power is applied to the relay coil as shown below NC To C O alarm NO anel p Ide i From e EA800 SSES logic No Alarm No Alarm Power is applied to the relay coil as shown below Relay State Energized To C oNC p alarm NO panel F IO d EA800 tE logic aE Alarm Power is removed from the relay coil as shown below This provides for a default alarm if the EA800 loses power in addition to the sensors alarms ide 0 From d EA800 SS logic EE Active Condition Sets the alarm to be active when an alarm condition exists Alarm Only Active Condition Sets the alarm to be active when an alarm condition exists or a warning is active Alarm or Warning default D 011 0152 15 Relay Operation 16 D 011 0152 Preparation Before you begin installation ensure that you properly plan the alarm system During the planning phase you will generate all the documentation you need to successfully install the EA800 base unit and sensors in the alarm system This is important because complete and accurate installation documentation aids in system maintenance later If the EA800 base unit will be connected to a remote alarm panel do not connect N CAUTION hapa the base unit to the alarm panel until after sensor connection and configuration is complete Connecting the remote alarm panel before configuring the EA800 senso
19. H UPYer U g Eet 1 Type 4 2 mA T i 2 Cooler 2 Pesdina ioc O return to Active Alarm 4 Laundry koom Jei K gt CH or Monitoring screen J Cooler 3 Hi b Cooler 4 Stati Delay H min Viewing the Event Log 52 The EA800 Alarm System logs up to 100 events in its Event Log At the minimum the following events are logged m System power on the date and time when the EA800 was powered on Sensor added indicates that a sensor was added Sensor deleted indicates that a sensor was deleted WRM Msg error indicates that an error message was generated Firmware updated indicates that the firmware was upgraded Alarm log cleared indicates when the alarm log was cleared Data log cleared indicates when the data log was cleared Note Pressing either arrow key will eventually wrap to sequence number 1 To review the event log perform the following procedure e Mi TE a d ng K KA E uei BZ e g Sensors Wiew Alarm Log 19 TRH F D Data Lo H Wiew Sensor Log ES a E E3 F About ERSEG lt j Or E I i ee PHLE II ee Press arrow keys to scroll up or down 12 19 28e7 6 19 29 PM through the logged events Sei Poller on DHTH 1 OR To return to Active Alarm D 011 0152 Operation Viewing the Sensor Log The sensor log provides a history of the environmental conditions for all installed sensors at a glance Up to 100 data sets are stored in the sensor log To view the sensor log perform the fo
20. R A en Cen i VR e ww Wiew Sensors Replace RF Sensor Replace RF Sensor Edit Sensor Edit Sensor Delete Sensor Delete Sensor Ferformance Fer formance Fanse C E See Figure 20 n V a s m T d m R as g aie H d 1 Uryers 4 Wireless c Cooler 1 L s Cooler 2 4 Laundry Room I Cooler E Cooler 4 Ur yer Type 4 2eimaA Reading ER Lat cc Hit opt ot ati Seck I min ULE See Figure 21 SENSUR EE IMF WSA STE ryer MAC Be CSF RBBB i EA Cooler 1 Firmware Wersioni Cooler 2 5 86 6316 4 2 Laundry Room Last Communication Cooler 3 Aq H Ze 16 52 46 PH Cooler 4 JE CAHE Cooler 2 Laundry Room Cooler 3 Cooler 4 Oryer 1 Sianal Strength Low CTT Are You sure M4 oraes diaa Se PH THE HE Can only replace the same sensor types Fress OK to continue Figure 19 Sensors Screen Map D 011 0152 77 Wire D Wireless H Hire Hireless Sensor 4 RE SG dm o melay Red Jolie Felaj 6 hia te Water Bug kelay T HA III H O Contact Felay 5 Water Bug HU Contact PSS emm t d t i SubZero Hater Bug HO Contact H C Contact E Common Name screen is dependent on the sensor being added If multi function only Parameter screens depend on the sensor being installed ooler Cooler 2 Cooler 3 Cooler 4 Freezer 1 Freezer 2 T R Sg j 4 Sensor 2 Sensor 5 Sensor 4 Sensor 5 Sensor 6 T
21. System Parameter Settings Configuring the system settings consists of selecting date and time display format setting sensor data collection frequency and enabling or disabling the audible alarm The default system configuration parameter settings are shown on page 14 To configure the system settings do the following 1 2 28 Unlock the base unit and access the MAIN MENU When programming use the arrow keys the Enter key and the three soft keys to advance through the menus and enter the appropriate information D 011 0152 Installation 3 Enter the SYSTEM menu and then select the CONFIGURATION menu as shown below d m Pe ki Ea K Sensors Sensors puas d ata Log System H Ie ae EE ee ER ES GER e BEIEUIE e St EI Set Time Oft LOUF atlon Change Password H RE KI a a GE 0 3 aLe LoOonrl EA TT DEE IE z rare fi Time Format Collection Frequency Buzzer EF Channel 4 The default date format is MM DD YYYY If you prefer DD MM YYYY format from the CONFIGURATION menu set the DATE FORMAT as appropriate for your region R IE p rare Pic Time Format Collection Frequency Buzzer EF Channel Set to D Wl rr et DAHA i Se Seas Choose setting for your region 5 Press F3 to confirm your selection When the CONFIGURATION menu is displayed skip TIME FORMAT if you want to use the default time format of 24 hour clock If you prefer a 12 hour AM PM clock set the time format a
22. Water Sensors Table 8 lists the water sensors available for use with the EA800 Alarm System Use of water sensors requires that at least one supervised water sensor be used Up to five additional unsupervised water sensors may be added in parallel on the same input where the supervised water sensor is configured Table 8 EA800 Compatible Water Sensors Operating Sensor Part Number Description Range Parameters Water Bug PN M 001 0094 Supervised water sensor NA 1 Water sensors are not effective nor intended for use in distilled or deionized water Multi Function Sensors Multi function wireless sensors may be connected to a wired sensor to act as a transmitter Table 9 lists the multi function sensor available for use with the EA800 Alarm System Table 9 EA800 Compatible Multi Function Sensors Operating Sensor Part Number Description Range Parameters Wireless PN M 001 0127 Wireless link for sensors See Dependent on sensor Multi Function page 16 for allowed sensors connected Contact Closure Sensors Table 10 lists the contact closure sensors compatible for use with the EA800 Alarm System Table 10 EA800 Compatible Closure Sensors Sensor Description NO closure Normally open contact closure such as door contacts motion detectors and glass break sensors NC closure Normally closed contact closure such as door contacts motion detectors and glass break sensors D 011 0152 13
23. change the value Use the PREV and NEXT soft keys to move the cursor to the next or previous digit Press the ENTER key to enter the value Harn ie R op fon Ven fi i ae fi les i SC mo Hireless elaus H eplace ensor ee iei r stem elete Sensor About EASHE Fer formance T C Be BRER rr eS H GE 4 Ba H E a H E Ce Be 4 SE E Custom Hame Sensor 4 i HU Contact S Se eS ee LML ee matches the input number used by the sensor or an alarm may result ooler Cooler 2 Cooler 3 Enter Walue 158 Cooler 4 e Sc Freezer 1 Freezer 2 Example values are shown Set all limit values as appropriate for your system vlaj g Enter Walue 058 Lei E H Enter Ualue LIDD d a Yi O eS WE SEU HODEN Sensor Added eee eae This is the start screen for the next Replace RF Sensor sensor to be added if any Edit Sensor Delete Sensor Fer formance T D 011 0152 43 Adding Wired Sensors Adding a Wired HA lll Humidity Sensor To add an HA III humidity sensor perform the following procedure Example shown set values as appropriate for your system d SS i Aen Ven 4 D Sensors H Wiew Sensors Relays Replace RF Sensor ie D SE EE stem elete Sensor About EASHE Fer formance K EN e Sa LHNLEI A ensor Flue b Ema S i Sensor E Red Custom Mame Sensor 3 White gt Sensor 4 HA III Mater Bug e HU Contact ee ee 2 22000 OOOO O PLHMLEL oT O LML KR NOTE The sensor number
24. eplace ensor Data Log Data Log Edit Sensor System System Delete Sensor About EASHE About EASHE Fer formance T C EE DESEN aS SSS PRETT NEH WIRELESS SENSUR lre Ire Wireless D Wireless H SEARCHING eS rr OSOS O eS rr OOS ee rr D 011 0152 23 Connecting Wired Temperature Contact Closure and Water Bug Sensors Note It may take a few minutes for the base unit to detect the wireless sensors At this point the NEW WIRELESS SENSOR screen is displayed and an arrow moves from left to right indicating that the EA800 is waiting to receive sensor ID data When the EA800 has communicated with the reachable sensors the SELECT SENSOR screen displays a list of wireless sensors detected m When a sensor is detected confirm that the ID number shown matches the ID number on the sensor s label a ken Weg SELECT SEHSOR m lf the sensors can communicate with the EA800 their IDs appear in the list as shown in the example at right Do not permanently install the sensors that appear in the list until you verify CAHE their signal strength when you program the RESET BUTTON A wireless sensors in the system later in the e e EE installation process MAC Address Label m If the list of number s on the screen does not contain the number found on the sensor s PC SENSOR MODEL NO board press F1 CANCEL to continue the Example EA WTS Wireless Temperature Sensor search process Figure 13 Wireless Sensor IDs and MAC Address Location Note
25. if any Edit Sensor Delete Sensor Fer formance MM D 011 0152 45 Adding Wired Sensors Adding a Wired Contact Closure Sensor The following procedure shown adds a N O contact closure sensor but is the same for N C contact closure Sensor Example shown set values as appropriate for your system ETT ie Gu Sensor lhe D Sensors H Wiew Sensors Wireless SE H PER 3 Sensor ata Log it Sensor System Delete Sensor About EASHE Fer formance K Dez EECHER ee ee LHNLEL TI E ae i 7 am S Geh S a Sensor Z Custom Hame SE e a ged ensor er Bug H i Ree er JO o OOOO O Enge LHNLEI Ses NOTE The sensor number must Select N O Contact or N C Contact match the input number J6 used by as appropriate the sensor or an alarm may result oor Door 2 Sensor Added Be ra __ niter Value LD indow Window 2 Window 3 cea This is the start screen for the next Replace RF Sensor sensor to be added if any Edit Sensor Delete Sensor Performance T 46 D 011 0152 Installation Adding a 4 20mA Sensor To add a 4 20mA sensor perform the following procedure There are some additional parameters to configure with this type of sensor including Unit of Measure and Resolution 4 20mA sensors can be used for monitoring a variety of conditions because the measured value corresponds to a current level which is configured to represent the conditions being monitored Follow the steps outlined below
26. it is powered on 2 Perform the procedure shown below to allow the base unit to search for the new sensor Unlock the EA800 as shown in Locking and Unlocking the EA800 on page 55 Jer K fae Cen D Sensors H Lieu Sensors a LE Relays DH Feplace FF Sensor Data Log Edit Sensor System Delete Sensor About EASHE Fer formance O SEARCHING OM JE gt oler Cooler 4 3 Select the detected sensor from the SELECT SENSOR screen If the detected new sensor is the same type as the replaced sensor the SENSOR REPLACED screen is displayed 4 Press OK F3 to return to the SENSORS screen If the replacement sensor appears in the list highlight it and press Accept If it does not appear in the list press Cancel F1 to continue the search process Press OK to continue D 011 0152 57 Editing Sensor Parameters 5 If the detected new sensor is not the same type as the replaced sensor the INVALID SENSOR TYPE screen is displayed Press OK F3 to return to the Can only replace the SENSORS screen same sensor types Fress OK to continue 6 Do one of the following e Replace the physical sensor with one that matches the type of the replaced sensor and repeat this procedure e Delete the sensor from the base unit and replace with the new sensor of a different type See Deleting a Sensor on page 59 and Adding a Sensor on page 57 7 If you wish to replace another wirele
27. screen If the remote sensor transmitter you are verifying is battery powered it may take up to 30 seconds for the base unit to receive a transmission from the remote sensor The base unit displays an approximation of signal strength as indicated by the number of filled boxes on the screen as shown at right Bech Auen Note The date and time shown at the bottom of the PERFORMANCE screen is the time stamp of the last received transmission 2 28 2087 12144 Sr Dh Ensure that at least 2 Signal Strength bars are displayed as shown at right If not it is recommended that the sensor be relocated until at least 2 bars are achieved More bars reduces sensor alarm latency reduces the probability of communication nal Strength alarms and increases battery life ign CIO Gdish For additional information on how to improve signal strength refer to Winland erat ra ae tre RH application note ANOO101 72 D 011 0152 Specifications Base Unit and Sensor Specifications The following table lists the specifications for the EA800 base unit sensors and accessories Table 14 Specifications Item Specification Dimensions Approximately 230 mm x 199 mm x 55 mm 9 375 H x 8 125 W x 2 25 D Weight Base Unit 0 27 kg 0 6 Ib Wireless Sensors 0 11 kg 0 26 Ib with batteries The EA800 base unit is mountable directly to 3 gang standard electrical enclo Mounting sure using pre drilled holes on the EA800 rear case The EA800 base
28. the 4 20mA sensor The full scale range is determined by the values entered in the Low Scaled Value and the High Scaled Value You must select the correct resolution in order to set the true range limits for the 4 20mA sensor you are install ing The available values are as follows Maximum Allowed Maximum Allowed Resolution Low Scaled Value High Scaled Value 1 9999 9999 0 1 999 9 999 9 0 01 99 99 99 99 0 001 9 999 9 999 Low Scaled 4 20mA sensor This parameter equals the environmental reading that results in a sensor Value output of 4mA or its minimum valid reading This is dependent on the setting of the resolution as discussed above High Scaled 4 20mA sensor This parameter equals the environmental reading that results in a sensor Value output of 20mA or its maximum valid reading This is dependent on the setting of the resolution as discussed above Hysteresis e Blue Red and White The Hysteresis setting helps prevent alarms from being set and reset temperature sensors continually if the environment is at or near the alarm set point by provid e HA III ing an acceptable variance For example if Hysteresis is set at 2 and the e 4 20mA sensor sensor High limit is set at 50 the sensor reading must decrease to 48 50 minus 2 in order for the alarm condition to reset to a no alarm condi tion Low Alarm e Blue Red and White The Low Alarm Limit sets the value that trips the low alarm when Limit temperature sensors exceeded
29. the adapter from the correct input connector headers by pulling the adapter up and off of the circuit board header connectors 3 Strip the ends of each of the sensor s wires as indicated by the gauge on adapter you just removed 4 Insert the stripped wire ends into screw terminals of the adapter as indicated by your EA800 Wiring Diagram you completed in the preparation phase Observe proper polarity See Figure 15 4 20mA Sensors EA800 Base Unit J5 J6 Aux Power Out Input N User 7 supplied lt ta cable 4 20mA Transmitter Connector EA800 Base Unit Powered 4 20mA Sensors EA800 Base Unit J5 J6 Input N Aux Power Out 4 20mA Transmitter Connector 4 20mA Sensors EA800 Base Unit J5 J6 Aux Power Out Input N User supplied lt ta cable O 4 20mA Transmitter Connector External EA800 Base Unit Adapter external J5 J6 Powered Power Aux Power Out Input N Adapter lt 4 4 20mA Transmitter Connector O EA800 Base Unit J5 J6 Aux Power Out Input N External Power Adapter CH J Q O 4 20mA Transmitter Connector EA800 Base Unit J5 J6 Aux Power Out Input N External Power Adapter Transmitter Connector Figure 16 EA800 Base Unit Wired 4 20mA Sensor Connections 5 Secure the connections using the setscrews on the adapter Check the connection by lightly pulli
30. the next sensor to be added if any D 011 0152 37 Adding Wireless Sensors Adding a Wireless Multi Function Sensor Using a Wired WaterBug Sensor Wireless multi function sensors are physically connected to wired sensors located elsewhere and provide a transmitter to send the signals monitored by the wired sensor to the base unit To add a wireless multi function sensor do the following 1 Unlock the base unit if necessary to continue programming See Accessing the MAIN MENU for Programming on page 28 2 Select SENSORS from the MAIN MENU and follow the steps in the following diagram 3 After you press the ENTER key the NEW WIRELESS SENSOR screen is displayed The EA800 searches for new wireless sensors indicated by an arrow that moves from left to right across the screen When an available wireless sensor has been detected it is listed in the SELECT SENSOR screen as shown below ee Wiew Sensors ERP Relays Replace RF Sensor arm divi E i censor fia Lo n os A e Data Log Edit Sensor System Delete Sensor About EASHH Ferformance of a E MEN WIRELESS SENSUR SEARCHING Ke AMER 4 Use the arrow keys to select the wireless multifunction sensor to be configured then follow the prompts to configure all screens for that sensor To add a wireless WaterBug sensor to the system perform the following procedure 1 Unlock the base unit if necessary to continue programming See Accessing the MAIN MENU for Progr
31. to program a 4 20mA sensor Example shown set values as appropriate for your system Harn ne Ne Ven fi R ad fi Sensors Lieu Sensors Wireless Relays LZ Replace RF Sensor le i Data Log Edit Sensor KS System Delete Sensor About EASHE Fer formance rs PHLE Ir R Ge D i 8 Se A S lte A HA III Custom Hame ES Sensor 2 y a i alah Hr JO Contac ei ensor ia CM Sol te p 2m H ensor e OR cena Sensor Mz ommon Mane Custom Hame ene Se K Dryer Picton Waite S EN e Zrh Jeh AB d o Ba J EP a T Ee eee ee IT High and Low Scaled Value are identified on the sensor as the sensing range It is important to know this range before selecting the resolution Low Scaled Value is the lowermost value or the value equivalent to 4mA High Scaled Value is the uppermost value or the value equivalent to 20mA indicated on the sensor See Table 11 on page 14 for available resolution values ee ee ee ee eee Hoh Alarm Limit GE Enter Value 81056 BAY Enter Walue 0036 lt b gt Enter Value 80408 PLHRLEL PREM EAT HME PREM NEST PLHRLEL PREM MEAT ee ee Hlarm Delay ajy H Enter alue H SE Lei Enter alue H DE PREM MEAT PCANEEL E CAALEL PR es e SENSE HODEN el Sensor Sensor Added Lieu Sensors e Replace RF Sensor Edit Sensor Delete Sensor Performance b SSS ne LIT SS Sa Ee ee D 011 0152 47 Configuring the Relays Configuring the Relays
32. unit and wireless sensors can be mounted to drywall or simi lar surfaces using the appropriate anchors not included Case Material ABS UL94V 0 rated EA800 Input Operating Volt age 1 2 3 11 to 26VDC 00mA current draw Standard commercial filtered and regulated power supply suitable Supplied by AC adapter not included see Accessories or alarm panel Note Power supply requirement does not include additional require ments for loads switched through alarm output relays where power is derived from EA800 EA400 terminal strip connections EA800 Aux Power Out Equivalent to DC input voltage used 11 to 26VDC Maximum output current 0 5A EA800 Real Time Clock Battery CR2032 3V Cell Wireless Sensor Input Voltage Either e 12VDC lt 100mA current draw using a 2 1 mm barrel plug center positive OR e 2xAA Alkaline Batteries 1 5V Cell Wireless Sensor Radiating Power minimum at PCB antenna connector e EA800 base unit 3 5 dBm e Sensors 2 5 dBm Wireless Sensitivity minimum at printed circuit board antenna connection e EA800 94 5 dBm e Sensors 95 5 dBm Low and High Limit Adjust Range Winland thermistor sensors only Temperature 80 C to 150 C 112 F to 302 F Note The Low and High Limit Adjust Range is dependent upon the sensor being used See Accessories on page 44 Humidity 5 to 95 RH Note The Low and High Limi
33. wireless sensor to base unit communications You should understand the environment in which the EA800 is to operate to minimize their affects on system performance 11 Decide the loop design you will use Figure 9 shows an alarm loop where alarm power is derived from the alarm loop Figure 10 shows an alarm loop where alarm power is derived from the power supply feeding the EA800 Note if using a self powered loop ensure the power supply can provide power for all loading conditions D 011 0152 From 11 26 VDC power supply 6 Input 1 Input 2 Input 3 Input 4 L 004 0520 J2 J8 Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 To alarm on closed loop circuit power gt supplied via loop Figure 9 Typical Alarm Loop Wiring Configuration External Power From 11 26VDC power s upply J6 Input 1 Input2 Input 3 Input 4 L 004 0520 J2 J8 Output 1 Output2 Output3 Output4 Output5 Output6 Output7 Outputs To alarm on closed loop circuit power gt Toalarm supplied via EA800 TO alarm Figure 10 Typical Alarm Loop Wiring Configuration Self Powered D 011 0152 Preparation 19 20 12 Create an interconnect wiring diagram for the system Identify the location of each sensor An example of a system map is shown in Figure 11 This example illustrates a system that includes multiple EA800 Multi Zone Environmental Alarm systems a Winland EA400 Multi Zone Environ
34. 011 0152 Installation Adding Wireless Sensors Go to the appropriate section for the wireless sensor to be added Wireless Temperature Sensor See Adding a Wireless Temperature Sensor on page 33 Wireless Humidity Sensor See Adding a Wireless Humidity Sensor on page 37 Wireless Multi Function Sensor See Adding a Wireless Multi Function Sensor Using a Wired Temperature Sensor on page 35 Multi function sensor may be programmed to operate with the following types of wired sensors e Low Temperature Sensor Blue Thermistor Probes See Adding a Wireless Multi Function Sensor Using a Wired Temperature Sensor on page 35 e High Temperature Sensor Red Thermistor Probes See Adding a Wireless Multi Function Sensor Using a Wired Temperature Sensor on page 35 e Ultra Low Temperature Sensor White Thermistor Probes See Adding a Wireless Multi Function Sensor Using a Wired Temperature Sensor on page 35 e WaterBug Sensor See Adding a Wireless Multi Function Sensor Using a Wired WaterBug Sensor on page 38 e NO Contact See Adding a Wireless Multi Function Sensor Using a Wired Contact Closure Sensor on page 40 e N C Contact See Adding a Wireless Multi Function Sensor Using a Wired Contact Closure Sensor on page 40 If the EA800 base unit will be connected to a remote alarm panel do not connect N SAULO the base unit to the alarm panel until after sensor connection and config
35. 4 0V 2 conductor wire connecting the EA800 to the 4 20mA sensor Vsensor Figure 6 14 20mA Sensor Wiring Diagram EA800 Aux Power Supply Figure 7 shows an example of the loop circuit for a 4 20mA sensor whose minimum operating voltage is greater than 8V when connected to an EA800 base unit that is powered with 12VDC If Vsensor gt 8V and Aux Power 12V EA800 External Supply 4 20mA Transmitter AUXE OWEN Max Load of 2000 includes 1000 of 22 AWG 4 0V 2 conductor wire connecting the EA800 to the 4 20mA sensor Vsensor Figure 7 4 20mA Sensor Wiring Diagram External Power Supply D 011 0152 11 Sensors Power Supply Sensor Voltage Selection In order to determine the power supply voltage necessary to ensure correct full scale operation it is necessary to identify all voltage drops within the current loop Figures 6 and 7 show an EA800 drop of 4 0 VDC This value accounts for the voltage drop generated by connecting the 4 20mA sensor to the EA800 using 1000 feet of 22 AWG wire Now it is only necessary to identify the operating voltage range of the 4 20mA sensor more importantly the minimum operating voltage Once identified the minimum operating voltage of the sensor can be added to the 4 0V voltage drop of the EA800 wire to determine the power supply voltage necessary to ensure correct full scale operation Example m Assume that a 4 20mA s
36. 9 Exporting the Stored Logs 70 D 011 0152 Troubleshooting Operating or setup errors are indicated by flashing data on the display Often a programming error also results in an alarm for the misprogrammed relay The table below shows and describes common error displays along with corrective action For updated information go to the EA800 page at www winland com and look for the troubleshooting section Table 13 Symptom Temperature reading indi cates maximum when temperature is actually less Troubleshooting Wired sensor is shorted Wired sensor cable has a short Sensor has failed Corrective Action Ensure that the sensor connection is not shorted A short equals zero resistance and thus the max imum value Replace damaged cable Contact Winland Technical Services at 1 800 635 4269 Temperature reading indi cates minimum when tem perature is actually greater Wired sensor is not connected Wired sensor cable has an open Sensor has failed Ensure that the sensor is connected to the cor rect header pins An open connection equals an infinite resistance and thus the minimum value Replace damaged cable Contact Winland Technical Services at 1 800 635 4269 Temperature display does not equal actual tempera ture Incorrect sensor programmed Verify the actual sensor connected to the sensor input is programmed appropriately Each temper ature sensor is limited to a specific oper
37. Configuration Settings on page 66 Loading a configuration from a USB drive See Loading Configuration Settings on page 67 Exporting stored logfiles for review or archiving See Exporting the Stored Logs on page 68 Note The base unit must be unlocked before you can perform any of the maintenance tasks in this chapter Locking and Unlocking the EA800 The base unit is normally locked When locked it cannot be programmed and certain maintenance features such as PERFORMANCE cannot be accessed Locking restricts access to these features to authorized personnel only If left unlocked the base unit locks automatically after a period of inactivity The current state of the EA800 is indicated by the text above the F1 soft key when the home screen is displayed m When UNLOCK is displayed the base unit is locked Press F1 use the PREV and NEXT soft keys to advance the cursor to the next digit and use the arrow keys to enter the value for the password The default password is 0800 19 CL TH F Enter Password Hp 19 CE TH F 7a F Got FIP mner s Bd F TH F TH F Ge Dr 0800 T GC PEANCEL PREL T HERT a a m When LOCK is displayed The base unit is currently unlocked Press F1 to lock it The base unit locks automatically after 30 minutes of inactivity RAR LEE g TA F 3 TH F A F GO F DH F Bo F A F o F r Ss if SE seim ee E RR ll ll D 011 0152 545 Pausing Monitoring and Cancelling Pause Pausing Monitoring
38. EES If conditions in the sensor s area return to the non alarm state within E S the alarm delay time the text returns to normal If conditions remain outside the programmed sensor alarm limits for longer than the delay Pending alarm time the screen changes to the ACTIVE ALARMS screen below m ACTIVE ALARMS Screen This screen is displayed when conditions monitored by any programmed sensor exceed one of its programmed ar limits for longer than the programmed delay period Only the active D Humidor d alarm s is displayed as shown in the example below See Viewing Active Alarms on page 50 for the procedure to access alarm information D 011 0152 49 Viewing Sensor Settings Viewing Sensor Settings You can view the readings of each installed sensor on the MONITORING screen To view details of a sensor s programmed settings and current readings on one screen perform the procedure shown below Note The MAIN MENU screen shown in the example procedure is displayed when the system is locked Sensor settings may also be viewed when the system is unlocked Use the arrow keys to highlight the desired menu item JPM LO L sensors Geo SC ghe Y Tas D Sensors Data Lo About ER Sm pe c Cooler 1 Type 4 2eimA 3 Cooler 2 Reading 180 4 Laundry Room oi a J Cooler 3 Hi ea l B Cooler 4 Stati Delay 5 min Viewing Active Alarms To view the current readings of a sensor with an active alarm Cool
39. Ea 85 Appendix D System Configuration Record ccscccceseseseeceeeeensecenseeseeeeesenenseeneeneneeoessneneeeenesonees 87 Warranty and Service Information ssunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nennen nennen nnmnnn mnnn 93 ii D 011 0152 General Information Overview The EnviroAlert EA800 Multi Zone Environmental Alarm System monitors the environmental conditions detected by the sensors connected to the base unit and provides alarm signals when monitored conditions at any of the sensors exceed the user programmable HIGH LIMIT or LOW LIMIT set points The alarm signals are provided via relay outputs that can operate with process controls security systems or other similar automated equipment The EA800 Alarm System can be configured with wired or optional wireless sensors sold separately The EA800 allows connection of up to 4 wired and 4 wireless sensors Setup and programming is done using the front panel keys and the liquid crystal display LCD on the base unit The display assists the user during setup and shows measured conditions for the monitored environment during operation The EA800 can monitor multiple critical environments using multiple sensor inputs Each sensor input alarm channel is designated a Relay Using the appropriate accessory sensors sold separately the EA800 Alarm System monitors and provides alarms for the following conditions m Normally open normally clo
40. See 0800 i een e d se EAEL PREL T HERT The arrows on the drawing indicate the direction of procedure flow In all procedures use the v keys to select menu options and to increase decrease alphanumeric values for programming options Use T PREV and NEXT soft keys F2 and F3 to move the cursor to the next digit when entering numeric data The functions of the soft keys F1 F2 F3 change and are defined on the screen in the area above each key If no text is shown above a soft key it means the key performs no function on the current screen Keys on page 6 describes the functions of each key on the base unit Note For convenient reference Appendix A Screen Maps on page 75 contains maps of all menus and screens Throughout the manual text that appears on the EA800 base unit screens is shown like this MONITORING Key names are shown in text like this F1 The current menu selection is highlighted on the screen by arrows on either side of the AAT ERT selection as shown in the example at right On this MAIN MENU screen the current selection Alarm Log is Sensors o Data Log Use the A or y keys to move the highlight to the desired menu item then press ei System TO About EASHE to make the selection 2 D 011 0152 General Information Block Diagrams Figure 2 shows a block diagram of the base unit interfaces and functions The EA800 provides eight relays for indicati
41. Sensor Sensor Physical Model Name Location Operational Parameters Installed LQI in bars MAC Address Notes D 011 0152 Appendix D System Configuration Record Parameter Settings Unit of Measure Resolution Low Scaled Value High Scaled Value Hysteresis Low Alarm Limit High Alarm Limit Alarm Delay Time No Alarm Relay State Active Condition 91 92 D 011 0152 Warranty and Service Information Winland Electronics Inc Winland warrants to the end user purchaser that each product of its manufacture shall be free from defects in material and factory workmanship for a period of two 2 years from the date of purchase when properly installed and operated under normal conditions according to Winland s instruction Winland s obligation under this warranty is limited to correcting without charge at its factory any part or parts thereof which shall be returned to the factory by the original purchaser transportation charges prepaid within one year of the date of purchase and which upon examination shall disclose to Winland s satisfaction to have been originally defective Correction of such defects by repair to or supplying replacements for defective parts shall constitute fulfillment of all Winland s obligations to purchaser under this limited warranty Repair service performed by Winland after one year from date of purchase will be for a reasonable service charge This limited warranty shall not ap
42. a presented provides the following event information Date and time of event Event description Code For Factory Use 12 24 2007 07 06 03 PM Sensor deleted 1 Exported Sensor Data The following is an example of exported sensor data The data is collected from all sensors at the intervals as specified in the Data Collection system setting every 5 minutes in this example Each sensor is allocated 11 data fields and 11 data fields are provided for all 8 sensors regardless of how many sensors are actually connected 12 26 2007 09 55 00 Piped oy 07 0 00 0 07070 69 57 070 700 000 770 698 7 0207 07070 705 07 EE GE d 0 707 0 707 07070 6672 255 0 0 0 070 070 0 65 F 105 0 070 Oyo oy Oe Oe ee Oe ee Oe Oi EE CN he NEE NEE E Oy OD 12 26 2007 10 00 01 PM 17 C 0 0 0 0 0 0 0 0 69 F 0 0 0 0 0 0 0 0 69 F 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 66 F 255 0 0 0 0 0 0 0 0 65 F 90 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 12 26 2007 10 05 00 PM 17 C 0 0 0 0 0 0 0 0 69 F 0 0 0 0 0 0 0 0 69 F 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 66 F 255 0 0 0 0 0 0 0 0 65 F 75 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 12 26 2007 10 10 00 PM 17 C 0 0 0 0 0 0 0 0 69 F 0 0 0 0 0 0 0 0 69 F 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 66 F 240 0 0 0 0 0 0 0 0 65 F 75 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 12 26 2007 10 15 00 PM 17 C 0 0 0 0 0 0 0 0 69 F 0 0 0 0 0 0 0 0 69 F 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 66 F 255 0 0 0 0 0 0
43. amming on page 28 2 Select SENSORS from the MAIN MENU and follow the steps in the following diagram 3 After you press the ENTER key the NEW WIRELESS SENSOR screen is displayed The EA800 searches for new wireless sensors indicated by an arrow that moves from left to right across the screen When an available wireless sensor has been detected it is listed in the SELECT SENSOR screen as shown below 4 Use the arrow keys to select the sensor to be configured then follow the prompts to configure all screens for that sensor as shown in the following diagram 38 D 011 0152 Installation Example shown set values as appropriate for your system NETT Er E fen Ven g s Ae Sensors Wiew Sensors peices Relays Replace RF Sensor Data L Edit 5 ech Seen eil hele enar About EASHH Performance a WE EH WIRELESS SENSUR ed WEE TE ress LY SEARCHING ARERR Relay 6 z oY elay Relay amp eS Se a ihe o D ane E Eeer Ka a p ee TE d Fed y Custom Hame Sump Fump White Kitchen D wi E H gel U Contac arn H C Contact Storage Room T SE ee LHNLEI Hlarm Uelay el Sensor Enter Ual 906 wl Sensor Added e View sengors nter Walue ee eplace ensor e Edit Sensor Delete Sensor Fer formance T LHNLEL FRES MEST II DK a This is the start screen for the next sensor to be added if any D 011 0152 39 Adding Wireless Sensors Adding a Wireless Multi Function Sensor Using a Wired Contact Clo
44. and Cancelling Pause To prevent false alarms when performing maintenance pause sensor monitoring Pausing stops monitoring and ignores active alarms for a 30 minute period When the pause function times out monitoring automatically starts To pause the EA800 perform the following procedure Unlock as shown in Locking and Unlocking the EA800 E fone og q GIS OS on page 55 S Relays ei Data Log i System About EASHE Er TEE RN Replace RF Sensor Edit Sensor Delete Sensor Performance ei RUE Dause Le sensors m oa a Replace EF Sensor Edit Sensor Delete Sensor Ferformance STEN PAUSED rine OR EK et Su PHUSED efor CH erior HK OT EHMHEEL To cancel pause and resume monitoring When the system is paused the SYSTEM PAUSED screen is displayed until pause times out 30 minutes or you cancel it You can access all functions in the main menu while the system is paused To resume monitoring instead of allowing the pause function to time out perform the following procedure Unlock as shown in Locking SYSTEM PAUSED and Unlocking the EA800 on page 55 CAS i4 a4 19 7a F ra F Bd F T 3 i 56 D 011 0152 Maintenance Adding a Sensor The procedure for adding a sensor to an existing system is the same as for a new system See Install the Wired Sensors on page 22 or Install the Wireless Sensors on page 22 for instructions on physically installing the sensor and then progra
45. ar Limited Warranty See Warranty and Service Information Notes 1 Where required this equipment is to be isolated from the mains supply by a limited power source as specified in EN60950 2 All terminals must be connected to a Class 2 Power Limited Circuit complying with the National Electric Code NFPA 70 Article 725 3 See Specifications on page 46 for power supply requirements Accessories 74 Accessories available for use with the EA800 Environmental Alarm System are listed below Table 15 Accessories Item Winland Part Number Description BZ 3 Audible alarm module PN 1183 Buzzer for connection to auxiliary relay output that provides audible alarm indication Power supply transformer PN L 020 0085 Regulated 110 VAC to 12 VDC gt 500 mA minimum transformer suitable for use with EA800 Note Power supply must be a limited power source per notes 1 and 2 in Table 14 D 011 0152 Appendix A Screen Maps Appendix A Screen Maps The figures in this Appendix illustrate the flow of all EA800 screens The displayed screen is dependent on whether an alarm Is active or not Uryger Cooler 1 Cooler 2 Laundry Room Cooler Cooler 4 Min LIT SE DOT 892190nHI Iana Elec Cc CR ee Electronics Inc 1ghts Reserved Short Addr DO Channel l Frotocol Version 1 2 Firmware Version 5 40 6316 1 2 D 011 0152 Walk in Cooler D Warehouse
46. arm output for Relay 4 OUTPUT 5 Form C relay alarm output for Relay 5 OUTPUT 6 Form C relay alarm output for Relay 6 OUTPUT 7 Form C relay alarm output for Relay 7 OUTPUT 8 Form C relay alarm output for Relay 8 AUX OUT Form C relay output that activates upon an alarm from any of the relays Relay 1 through Relay 8 Antenna RF receive and transmit Antenna RF receive and transmit Access Control and Passwords The EA800 base unit is normally locked to prevent unauthorized use The currently active function of the F1 soft key UNLOCK or LOCK is displayed above the key The locked and unlocked states are described below Note The base unit locks automatically after 30 minutes of inactivity if the user does not press the LOCK soft key F1 m Locked This is the default state and limits access to the EA800 to viewing only Rm TOUR OI SIS UNLOCK is displayed above the F1 soft key indicates that the base unit is E i pomo currently locked Pressing the F1 soft key prompts the user to enter a password to unlock the base unit permitting full access to all screens and functions The HOME key MENU key and the MAIN MENU options shown on the screen at right are available to the user when the base unit is locked m Unlocked When the base unit is unlocked LOCK displayed above the F1 soft key and all information programming and maintenance screens may be viewed and programming changes may be made Pr
47. ating range Display flashes repeat edly between the Winland Electronics Inc screen and a blank screen The EA800 reboots repeatedly and fails to successfully com plete the boot process Cycle power to the EA800 and wait for a period of time before reapplying power If a USB drive is attached to the USB port remove it and cycle power as noted above If the problem recurs contact Winland Technical Service at 1 800 635 4269 The display flashes while displaying the ACTIVE ALARMS screen D 011 0152 A sensor s reading has exceeded a set limit A wireless sensor is not commu nicating with the base unit Verify the environmental conditions of the sen sor Verify the received signal strength as outlined in Verifying RF Signal Strength on page 72 71 Verifying RF Signal Strength Verifying RF Signal Strength Viewing Signal Strength for a Wireless Sensor To verify the RF signal strength received by the EA800 perform the following procedure d m ES op fe Ven Unlock the EA800 as shown Censors Lieu Sensors in Locking and Unlockin Relays e Replace RF Sensor ine Ge on page 55 j Data Log Edit Sensor g e System op Pontos Sensor ou erformance oer ny ar lt aa Ele a Cooler Sianal Strength Sianal Strength Acquiring Ho Data S PLHMLEL oT O IC NE UIE To return to SELECT SENSOR screen ianal Strength WE Be TTT Wi L EC teddies PA E ee ee Au To return to home
48. d freezers 50 C to 70 C 58 F to 158 F High Temp Red waterproof PN M 001 0087 Thermistor waterproof high tempera ture sensor 0 C to 150 C 32 F to 302 F Ultra Low Temp White Stainless Steel PN M 001 0111 Thermistor Stainless Steel Probe Ultra Low Temperature Sensor 80 C to 0 C 112 F to 32 F Wireless Temp PN M 001 0125 Stand alone wireless temperature sensor 0 C to 50 C 32 F to 122 F D 011 0152 General Information Humidity Sensors Table 6 lists the humidity sensors available for use with the EA800 Alarm System Table 6 EA800 Compatible Humidity Sensors Sensor Part Number Description Operating Range Parameters HA III PN M 001 0091 Humidity monitoring module 5 to 95 rh non condensing Wireless PN M 001 0126 Wireless humidity monitoring 5 to 95 rh Humidity module non condensing 4 20mA Sensors Theory of Operation Industry standard 4 20mA sensors can be used with the EA800 However it is important to verify that this type of sensor will operate properly over the entire output range Figure 6 shows an example of the loop circuit for a 4 20mA sensor whose minimum operating voltage is 8V or less when connected to an EA800 base unit that is powered with 12VDC If Vsensor 8V and Aux Power 12V EA800 4 20mA Transmitter AD SIS Max Load of 2000 includes 1000 of 22 AWG
49. eesseeeseeeseueeseeesseessueesaeeeseeesueeseeeeseeeesaes 11 Ree ele e EE 11 Power Supply Sensor Voltage Gelechon 12 EE 13 Multi FUNCION SOM E 13 COMC EE 13 Sensor Parameter Reder 14 FASTA COMM isep secede oteerneate esc cards ne eres aaa ces secre Sue menses sedi ocesntaes eae bea amen eee ousereesees 15 We AU AMON oe ncurses ceases cc ncee EE EE a EEEE E E EEEE 17 BONS BAN d Le EE 21 TOS ANG SUD OSS FSC e WEE 21 Power Requirements ccccccecceeceecsececeeseeseeceeeseccensaeeceeseeaeesaeeceesseesueseeseaeseeenenteeeaeeseeseeessaeesenses 21 Mounting the EA800 Rear EE 21 MEANE ee TE 22 EASO00 Base Unit Power EE iiaia ka EEEE Ea EE EREE ENEE 22 install the Wireless 6 E S scssinrasresnk renin neea NEEESE BEEN ORERE AA eane E ETAren 22 Connecting Wired Temperature Contact Closure and Water Bug Gensors 24 Connecting Wired HA IIl Humidity Sensors nannnannnnennnennnennnnnnnrnnnsrrnsrensrrrnrrrsrrrsrersrrrsrersrrrnerenn 25 Connecting Wired 4 20MA Ee 26 EENHEETEN 27 FF FOG FUNG RE 27 Accessing the MAIN MENU for Programming ME 28 Configuring System Parameter Settings cccccccsseccceeeeeeeseeeeeceeeseeseseeesaeeessaceeeseegeessaeeeesaass 28 SENI ME CUNEN DIE eege 31 Setting the WNC tescuctacracecesitmecesncagus gencenesenctsasenndemataedentesen eadaqiecueteesstauiecenedoubecesadaceaeedernedsessedeexdeneass 32 e Ze later 33 Adding a Wireless Temperature Sensor nennnsnnesnnnsrrnrnrrrnrnrnrrsrensrrrsrrrrr
50. efore important to verify the signal strength by approximating the worst case scenario the RF signal may encounter 42 D 011 0152 Installation Adding Wired Sensors m Low temperature sensors Blue Thermistor Probes See Adding a Wired Temperature Sensor on page 43 m High temperature sensors Red Thermistor Probes See Adding a Wired Temperature Sensor on page 43 m Ultra Low temperature sensors White Thermistor Probes See Adding a Wired Temperature Sensor on page 43 HA III humidity sensor See Adding a Wired HA III Humidity Sensor on page 44 WaterBug sensor See Adding a Wired WaterBug Sensor on page 45 N O Contact See Adding a Wired Contact Closure Sensor on page 46 N C Contact See Adding a Wired Contact Closure Sensor on page 46 4 20 mA See Adding a 4 20mA Sensor on page 47 Adding a Wired Temperature Sensor The procedure shown below adds a wired Blue temperature sensor but is applicable to the wired Red and White temperature sensors as well The Hysteresis setting helps prevent alarms from being set and reset continually if the environment is at or near the alarm set point by providing an acceptable variance For example if HYSTERESIS is set at 1 and the sensor High Alarm Limit is set at 158 the sensor reading must decrease to 157 157 minus 1 in order for the temperature alarm to reset to a no alarm condition When setting numeric values use the arrow keys to
51. ensor whose operating input voltage range is 10 30V has been selected for use Therefore the minimum operating voltage of the sensor is 10V Vsensor When the 4 0V drop of the EA800 and wire is added it can be determined that at least 14VDC is needed to power the loop m If the EA800 is connected to a 12VDC power supply use of the sensor in this example requires an external power supply of at least 14V as shown in Figure 7 It is important to not exceed the maximum operating voltage of the 4 20mA sensor as specified within the sensor s product specification The following formula provides the basis for the selection matrix shown in Table 7 Please use Table 7 to select either the proper sensor rating to be used with a known power supply or select a power supply for a known sensor rating A Vec X 023 where m R Loop resistance of 200 E Vo Power supplied to EA800 or Aux Power Out E X Sensor voltage max Table 7 4 20mA Voltage Select Matrix Power Supplied to EA800 Vsensor max Maximum Power Supplied to EA800 or Vsensor max Maximum or AUX Power Out sensor voltage rating AUX Power Out sensor voltage rating 11 VDC 7 VDC 19 VDC 15 VDC 12 VDC 8 VDC 20 VDC 16 VDC 13 VDC 9 VDC 21 VDC 17 VDC 14 VDC 10 VDC 22 VDC 18 VDC 15 VDC 11 VDC 23 VDC 19 VDC 16 VDC 12 VDC 24 VDC 20 VDC 17 VDC 13 VDC 25 VDC 21 VDC 18 VDC 14 VDC 26 VDC 22 VDC 12 D 011 0152 General Information
52. er 1 H LY Cooler 1 Cooler 1 22 H Reading It Io lt gt Hysteresis 1 fara SC High Limit se F Low Limit 58 F to exit UAL OLE Po BALK a MISE There are six conditions that may be shown in the alarm screen E Comm Indicates that the wireless sensor is not communicating with the EA800 High The sensor s current reading is greater than the programmed high threshold Low The sensor s current reading is less than the programmed low threshold Batt The sensor s battery is low Cut Supervised water sensors only cable is cut or disconnected m Fail Indicates that the sensor reading is exceeding the known range of the sensor More than one alarm condition may be displayed For example if a wireless sensor detects a high reading and then stops communicating with the base unit the alarm log will indicate a Comm High alarm This type of alarm can be logged only if the high reading occurred prior to the communication failure 50 D 011 0152 Operation Viewing the Alarm Log This alarm log is a quick view of the 20 most recent alarms Up to 100 alarms can be reviewed by selecting Data Log from the MAIN MENU then selecting View Alarm Log To review the alarm history and review a specific alarm stored in the log perform the following procedure Note The MAIN MENU screen shown in the example procedure is displayed when the system is locked This alarm log may also be viewed when the system is unlocked E ETT ine fi
53. essing the F1 soft key locks the EA800 base unit and protects it from unauthorized or unintended programming changes log downloads and firmware uploads Data Lo About RG The base unit allows the use of two passwords for unlocking m The factory default password is 0800 This password cannot be changed or deleted m A second optional password may be set by the user To create a second user password see Changing the Password on page 63 8 D 011 0152 System Configuration Parameters General Information The EA800 base unit requires certain system level information as outlined in Table 4 Table 4 System Configuration Parameters Parameter Selections Factory Default Description Date Format ie MM DD YYYY MM DD YYYY Sets the desired date format for all event time stamps e DD MM YYYY Time Format 12 hour 24 hour Sets the desired time format for all event time stamps e 24 hour Data Collec e 30 seconds 5 minutes Sets the interval for collecting and recording data from the tion Fre e 1 minute sensors The data collection frequency applies to all sen quency e 5 minutes sors The EA800 provides approximately 10 000 data e 15 minutes points to be collected regardless of the frequency 30 minutes selected The estimated time duration covered for each GO minutes data collection frequency is listed below 30 seconds 3 5 days 1 minute 1 week 5 minutes 1 month 15 minutes 3 months 30 minutes 6 months
54. file to download CGDp DI CFG AT 1228 175439 CFG Ki NaI AS F WHEW A4 CFG KREE ER To return to LOAD SAVE CONFIG Remove USB drive when cy import is complete OR To return to the home CH screen D 011 0152 67 Exporting the Stored Logs Exporting the Stored Logs You can export the logs stored in the EA800 for archiving or later review The export procedure exports the alarm log data log and event log files To export the logfiles perform the following procedure Unlock as shown in Locking and Unlocking the EA800 on page 55 Gi Appears only if a USB drive is not installed The screen displays the progress of the data export Remove USB drive when export is complete tanto W wee tent tos W ca ieee VE iew Sensor Log Data Log H ke D Export All Logs H 5 System Ka Clear Alarm Log About ERSHE ae Clear Sensor Lo ERC S as Insert USB Drive To return to SELECT SENSOR screen Data Export Complete OR ry To return to home screen The EA800 stores the log files on the USB drive in comma separated value CSV format The files are named in the format XYYMMDD HHMMSS txt where WA A E or D e A Alarm log file e E Event log file s D Sensor data log file E YYMMDD is the current date E HHMMSS is the current time in 24 hour format You can rename the files to more easily identify the EA800 system they came from however the first character designating the log type A E or D
55. ime starts and ends See Setting the Time on page 32 Changing Sensor Data Collection Frequency Note Update the system s Configuration Worksheets to document any changes Note The default collection frequency is 5 Minutes See Table 4 on page 9 for information on correlating data collection frequency to the number of data points collected To set the data collection frequency perform the following procedure Er E Ei iz Unlock the EA800 as shown Sone Set Time in Locking and Unlocking ee er Se Ee H he EA800 ata Log ange Passwor Maer ee System H Update Firmware About EASHE Load Save os GE P a HE Format o seconds 1 Minute Time Format D 23 Minutes H DH Collection Ee H pa 15 Minutes pF thannel 38 Minutes BA Minutes PRETT O ne aes Set tot Time Format D Minutes G Collection Frequency H Buzzer EF Channel II DK ee a D 011 0152 61 Changing the Buzzer Setting Changing the Buzzer Setting d WARNING Changing the buzzer setting to DISABLED turns off the audible alarm tone from the base unit Do not disable the buzzer unless you are sure you do not want the base unit to emit an audible tone when an alarm occurs The active condition of the buzzer mirrors what is assigned to the auxiliary relay Note Update the system s Configuration Worksheets to document any changes Note The default buzzer configuration is ENABLED and the active condition of the on board buzzer mirror
56. ing See Accessing the MAIN MENU for Programming on page 28 2 Select SENSORS from the MAIN MENU and follow the steps in the following diagram 3 After you press the ENTER key the NEW WIRELESS SENSOR screen is displayed The EA800 searches for new wireless sensors indicated by an arrow that moves from left to right across the screen When an available wireless sensor has been detected it is listed in the SELECT SENSOR screen as shown below 4 Use the arrow keys to select the sensor to be configured then follow the prompts to configure all screens for that sensor as shown in the following diagram 40 D 011 0152 Installation Example shown set values as appropriate for your system Aer ES T TE Ke i re 5 V Wiew Sensors L Wireless d 6 Relays a Replace RF Sensor E it Sensor ain Delete Sensor About EASAG Ferformance MM Kl n WE ee Jo OOO O I SERRCHIMG ARBRE R mk d KA d a Felay Relay E CANCEL CANCEL E Ma E R Ge sn 4 fe P 5 Custom Hame Door Sc i e H WE VE ater Duo Lpdou D Ho Contact O Window 2 H C Contact Window 5 Weg eS ee n ee J O 0000 Select N O Contact or N C Contact as appropriate a SENSUR HODED W Ser Sor A Sensor Added View Sensors Enter alue FD e Replace RF Sensor it Sensor j lt Edit Delete Sensor Fer formance T LAMLEL FREU NEST Oo OE a This is the start screen for the next sensor to be added if any D 011 0152 41 Adding W
57. ireless Sensors Verify Wireless Signal Strength After temporarily mounting the wireless sensors in the desired location verify the signal strength at the base unit by performing the following procedure to verify the signal strength of each programmed wireless sensor It may take as long as 30 seconds to acquire the current signal strength Perform the following procedure to verify the signal strength of each programmed wireless sensor TZ ES Ne Ven ak A e fi Sensors Wie Sensors Cooler 4 Relays Replace RF Sensor Ka Data Log Edit Sensor Delete Sensor System About EASHE Fer formance Signal Strength w Signal Strength a Signal Strenath Acquiring Ho Data Low E E A E Hih H4 HS CHRS 11da aa FM i a E a E No Data is displayed until a signal is received and then the signal strength is displayed as shown in the last screen If No Data is displayed in place of bars it indicates that recent signal strength information has not been received If this persists for 1 2 minutes without displaying any performance bars it is a strong indication that your sensor is placed out of range with the base unit If fewer than two bars are shown it is recommended that the sensor be relocated to obtain a better signal Refer to the instruction sheet included with the wireless sensor for details on ensuring optimum signal strength The wireless environment can change throughout the day because of other activity in the vicinity It is ther
58. kings screened on circuit board EA800 can be damaged if power polarity is reversed Aux Power Out 11 26 VDC power out connection for EA800 accessories requiring power such as HA IIIl Humid Alert This output voltage equals that of Power In and is current limited to a maximum of 500 mA Connect only accessories specified in this manual to the Aux Power Out connection Connection of unsuitable loads to this connection may damage the power supply and EA800 or result in improper or unreliable operation Note Accuracy for the HA III sensor is stated at 12VDC input lf Aux Power Out is used to power the HA III and is not 12VDC then the accuracy of the HA III is compromised D 011 0152 7 Access Control and Passwords Table 3 EA800 Base Unit Connector Functions continued Connector Designation Function INPUT 1 Wired input for Relay 1 external temperature water 4 20mA contact closure or humidity sensor INPUT 2 Wired input for Relay 2 external temperature water 4 20mA contact closure or humidity sensor INPUT 3 Wired input for Relay 3 external temperature water 4 20mA contact closure or humidity sensor INPUT 4 Wired input for Relay 4 external temperature water 4 20mA contact closure or humidity sensor OUTPUT 1 Form C relay alarm output for Relay 1 OUTPUT 2 Form C relay alarm output for Relay 2 OUTPUT 3 Form C relay alarm output for Relay 3 OUTPUT 4 Form C relay al
59. le ae KE EE 57 PRS OAC IG et e EE 57 EGMMNG SENSO EE 58 Reprogramming a Relay ccccseccsecceeeeeeeeeeeeeeeeeeeeeeeeseeeeeeeeeeeeeeeeeeesaeegeeeeesaeeseeseeseeeseeesaeeseeeeeeeeses 59 Be SUING E 59 Rea OIG Ne Date el EE 60 CAGNANO INE TIME d VE 60 Changing the Date or Time Setting ccccccccsccsseecessseeseeeeeseeeessoeeesoeessoeseseuacesoeaesouaeensatseeeesenses 61 Changing Sensor Data Collection Frequency EE 61 Changing the Buzzer SCIHING E 62 nanging ne Paso WO EE 63 Le ari Ce PVA EO e DE 64 SICA TG SONS OF OG EE 64 JOG TIING Me au EEN 65 Saving Configuration SettinS c c6 ccccesecessesccesceesescsescccssesenceesesnaeeecscesesesceseescceccencuseeenccenstensoes 66 Loading Configuration Settings ihecpentacanserenueluinneneseuserariapuad narada Er EESO aE 67 EXPONUNT Tine O ALOS e E R ERN 68 EO OTIS Fil AN D WE 68 OOS GV Sa sesen tne peat ncr aca ve Sateen etapa swine nixdenmieaancuioneaenoh EE T 69 SN giele ae D lt EE 69 UFOS SOO NC ME 71 STI Ce Siga UCN EE 72 Viewing Signal Strength for a Wireless Gensor 72 SCCM d S ceninin e E peewee meelanecuntedatny sebeenes ermcuteveeveastc setwetamdeneuaet 73 Base Unit and Sensor Specifications E 73 EE eege Eege 74 Appendix A Screen IAS icc igesrete sais cuenta aacrusinte steed oneunnedansewedesenusnenstnedesuesegucstevenunesiandenbustdeclerusveasusteeesias 75 Appendix B Planning Worksheet E 83 Appendix Wiring Diagram ceed sete cases het anaa aa aaa aa aaa aaa
60. llowing procedure e Gi ZC a NETT ie une BZ Er TE aa o oo q o eege re q Ata Lo lel sensor Log L 63 F About EASKHH Dr a a SS Sess es a a i Press arrow keys to scroll up or down AD through the logged data 12725 che 11 46 66 FMH IS Br F ri F BE F OR Ti F Dr EE To return to Active Alarm ee 3 2 e tec Viewing Firmware Information The About EA800 menu item displays the currently running firmware version To view the firmware version do the following Note The firmware revision number shown indicates the firmware version currently installed i ZS re F re F cI 3 i tants A See D Abouteisag g 5 H 1 H319 47 1 Copyriaht oc ZAAT el To return to Active Alarm Winland prec onic Inc or Monitoring screen All Fiahts Kezerued pea er a D 011 0152 53 Viewing RF Information Viewing RF Information The ABOUT RF screen displays the EA800 base unit s MAC address the RF channel currently in use the RF communications protocol version and the RF subsystem s firmware version To view the RF settings perform the following procedure Note The firmware revision number shown indicates the firmware version currently installed cl a G fSObS np oe g ll GOUD THT iE 2881 8319 A cna E EE LC3 CR Protocol Version 1 2 Sach or Monitoring screen Minland Electronics Inc Firmware Wersion All Rights Reserved Gil RHZIR 1 2 see fo Jil 54 D 011 0152
61. m Delay Time ooler fp O LAHALEL FREM HEAT Select the sensor to edit CEET sa 2S Coire Yv Set to FRO E G Hi h Alar Limit HU iah Alarm Limi Low Alarm Limit Hysteresis Alarm Delay Time mn 13 CH F mre F 63 F re F To edit another parameter when done editing a rr Select the parameter to be edited Hoh Hlarm Limit Enter Value 6295 Use PREV NEXT and arrow keys to change value ee Ee to lock 58 D 011 0152 Maintenance Reprogramming a Relay Note Ensure that the system s Configuration Worksheets are updated to document any changes A Relay can be reprogrammed as desired at any time Perform the procedure outlined in Configuring the Relays on page 48 to reprogram any relay in the system Deleting a Sensor Note Update the system s Configuration Worksheets to document any changes To delete a sensor perform the following procedure Unlock the EA800 as shown BEE dg mg in Locking and Unlocking Sensors a Y the EA800 on page 55 Relays Age Cie Wiew Sensors Replace RF Sensor Data Log Edit Sensor System D Delete Sensor d About EASHH Fer formance hal Poe es BETEN DELETE SEHSUR TT SENSOR DELETED Fuer y Cooler 1 Oryer 1 Oryer 1 GC i Taler ai Are you sure Cooler 4 Fe PCHMGEL YES es a OK 2 Voie Liew Sensors Replace RF Sensor Fa CH Edit Sensor Delete Sensor H Performance T E D 011 0152 59 Changing the Date Format Cha
62. mental Alarm system and a Winland EA200 Multi Zone Environmental Alarm system Alarm Panel Output 1 Relay 7 Output 2 Relay 2 lt Output 3 Relay 3 lt Output 4 Relay 4 lt Output Relay lt Relay Output 1 Outputg Relay 6 lt 4 Ycn2 Relay 2 Output 2 Output 7 Relay 7 lt 4 Relay 3 Output 3 Output 8 Relay 8 lt Relay Ouput5 EA800 No 2 CHE Pelayo LOuntg Output Zone 1 lt Relay Output Output2 Zone 2 Relay8 oer Output 4 Zone 4 EA800 No 1 EA400 Storage Room 3 Sensor 1 Cooler1 Sensor Cooler 2 Sensors sy Sensor 5Y Sensor 7Y Sensor 6 Chi Chi Chi Alarm panel installation area Rear Sensor A Entry Sensor A Front Sensor Y Entry Ch2 Ch2 Ch2 Front Desk Sensor 5 Sensor Y Ch2 Sensor 2Y Gensora Sensor 1 Sensor 2 Sensor 3 Sensor 4 Sensor 1 Sensor 3 l Conference Room Men s Room Sensor 2 Freezer 1 Freezer 2 Room 1 Room 2 Women s Room Figure 11 System Interconnect Wiring Diagram Example 13 Determine the cabling required to complete the installation as indicated by the loop design the sensors you have selected and the system interconnect wiring diagram 14 Complete the System Configuration section on the copy of the System Configuration Record
63. mity with all applicable requirements for its placing on the European Union market 4 D 011 0152 General Information Monitoring Screens The EA800 user interface is menu based During normal system monitoring one of the following three screens is displayed depending on the current state of the programmed sensors The MONITORING home screen is displayed when there are no active alarms The screen lists all programmed sensors connected to the base unit and their current reading or state The MONITORING home screen displays pending alarms in reverse video as shown in the example at right 71 exceeds the temperature limit for Sensor 2 so it is shown as light text on black Pending alarms indicate that the programmed lim its for the sensor have been exceeded but the sensor s programmed delay time has not elapsed yet If the monitored conditions continue to exceed the programmed limits for longer than the programmed delay period the pending alarm will become an active alarm The ACTIVE ALARMS screen is shown when one or more sensors are in an active alarm or warning OKT state If more than one alarm is active each will D Walk in Cooler be listed on the screen In the example shown Warehouse Walk in Cooler and Warehouse alarms are occurring simultaneously D 011 0152 5 Keys Keys Figure 4 shows the base unit display and entry keys The keys are described in Table 2 Table 2 EN VIROALERT
64. mming the sensor in the EA800 base unit Note See Pausing Monitoring and Cancelling Pause on page 56 and pause the base unit before you begin so you can set up the sensor without tripping the alarm Note If adding more than one sensor add them to the system one at a time Power on one sensor and add it to the system then power on the next sensor and add it Do not power on all sensors at the same time Note Update the system s Configuration Worksheets to document any changes Replacing a Sensor The EA800 allows you to replace an existing programmed wireless sensor with another of the same type When replaced the original sensor s programmed settings and parameters are retained and applied to the new sensor If you need to change settings other than those provided in the Edit Sensor screen you must delete the existing sensor and then add the replacement sensor Note See Pausing Monitoring and Cancelling Pause on page 56 to pause the base unit before you begin so you can replace the sensor without tripping the alarm Note f adding more than one sensor add them to the system one at a time Power on one sensor and add it to the system then power on the next sensor and add it Do not power on all sensors at the same time Note Update the system s Configuration Worksheets to document any changes To replace an existing wireless sensor 1 Physically replace the sensor with another of the same type and ensure
65. must match the input number J6 used by the sensor or an alarm may result Hab Alarm Limit Es UmM1dor Computer Room Barn e Enter Values 99 Enter Walue 41 Storage Room a Warehouse LAMLEL NEST 5 Added V e Enter Value 606 ee eee ai e S 7 ee O O OOOO O LHALEL FFEN Heal ee ee ee ee Heu Sensor Wiew Sensors Replace RF Sensor Edit Sensor Delete Sensor Fer formance b This is the start screen for the next sensor to be added if any 44 D 011 0152 Installation Adding a Wired WaterBug Sensor To add a WaterBug sensor perform the following procedure Note A supervised WaterBug sensor must be used Example shown set values as appropriate for your system NETT ES b op fae Ven r are S Wiew Sensors Mireless lee Replace RF Sensor Data Log r RT SE pm cust elete Sensor it EAE Fer formance About EASE SSS Sa WR RN a a D Ge 1 Fi E Boegen Dr fi Sensor Z Custom Hame Sensor 3 nate Sensor d e HA III i D d is HRZ 0 Contac M LHNLEL II LHNLEL TI LHNLE rr NOTE The sensor number must match the input number J6 used by the sensor or an alarm may result Hlarm Delay SENSORE HODED Z Sum Pump Vv A v Sensor Added LS chen Enter Value 008 eg KS Storage Room REENEN CUCEITTBEEITTTHEZTT Eege eet m R a Ven fi Lieu Sensors This is the start screen for the next Replace RF Sensor sensor to be added
66. nd or fire hazard N CAUTION Connect only sensors specified in this manual to the wired and wireless input connections Using sensors not specified in this manual may damage the EA800 or cause improper or unreliable operation 8 CAUTION Do not connect a load to the AUX OUT or OUTPUT 1 through OUTPUT 8 relay outputs that exceeds limitations stated in the Specifications section of this manual Loads exceeding the specified limitations may damage the EA800 or result in improper or unreliable operation AN CAUTION The EA800 printed circuit board PCB contains electrostatic discharge ESD sensitive devices To help prevent damage caused by ESD observe appropriate ESD handling rules whenever the PCB in the EA800 is exposed Batteries shall not cause explosion or produce a fire HAZARD as a result of CAUTION Se Ge excessive charge or discharge or if a battery is installed with incorrect polarity If the equipment is used in a manner not specified by the manufacturer the CAUTION protection provided by the equipment may be impaired Mounting the EA800 Rear Plate The base unit has a removable rear plate that may be attached to a 3 gang electrical enclosure or directly to a wall 1 E Remove the rear mounting plate from the base unit as follows Pull the rear mounting plate down and away from the EA800 main chassis The retainer tabs on the main chassis disengage from the holes in the rear mounting plate Completely remove
67. ng on each connection 6 After connecting the wire ends to the adapter align the adapter to the correct header pins as indicated by your EA800 Wiring Diagram and press the adapter fully onto the header connector pins 26 D 011 0152 Installation Connecting the EA800 Alarm Outputs If the EA800 base unit will be connected to a remote alarm panel do not connect N EE the base unit to the alarm panel until after sensor connection and configuration is complete Connecting the remote alarm panel before configuring the EA800 sensors will result in false alarms at the remote panel If alarm loops will be controlled by the EA800 install all required wiring from alarm loops to the EA800 mounting location 2 Connect the alarm loop leads to the terminal block adapter Attach the adapter to terminals C and either NC or NO on the appropriate circuit board header connector 3 Repeat the previous step for each alarm loop 4 Engage the mating tabs on the EA800 main chassis into the mounting plate upper hinges 5 Pivot the bottom of the EA800 main chassis into closed position while aligning the retainer tabs on the main chassis with the holes in the rear mounting plate and ensure that the wiring is not pinched stressed or protruding between the chassis halves 6 Snap the main chassis closed onto the mounting plate When properly closed the main chassis and mounting plate mating surfaces are flush Programming When powered up
68. ng when a programmed alarm limit has been exceeded or a warning condition exists An additional AUX Auxiliary Output relay provides an output signal to an optional audible alarm or strobe that is activated whenever an alarm condition exists EA800 Base Unit elay 1 coil contol ogy arsan Relay assignment Output 6 and coil control logic LAUU M Z4 Se System Control je Se S Sensor 7 Y Wireless Sensors LD D gt OD O m O Figure 2 EA800 Environmental Alarm System Block Diagram The EA800 can be made part of a larger security system as shown in Figure 3 In a security system there may be more than one EA800 installed along with other components such as the Winland EA200 or EA400 multi zone environmental alarm systems EA800 Base Unit Relay 1 coil control logic Relay 2 coil control logic Relay 3 coil control logic Relay 4 coil control logic Sensor 1 Sensor 2 Sensor 3 Sensor 4 cel Relay assignment and coil control logic L SSS Alarm Panel NYI ensor 6 T Sensor 7 F WV From other e EA800 EA400 and EA200 d Wireless Sensors Environmental Alarm Systems EA800 Base Unit Relay 1 coil control logic Relay 2 coil control logic Relay 3 coil control logic Relay 4 coil control logic Sensor 1 i Relay assignment iii and coil control logic rp Relay 8 oe Sensor 2 S Sensor 4 cel Wireless Sensors Figure 3 Facility Security Sys
69. nging the Date Format Note Update the system s Configuration Worksheets to document any changes Note The default date format is MM DD YYYY To change the date format perform the following procedure aE EF E ae Unlock the EA800 as shown Sensors Set Time in Locking and Unlocking Relays gt gt MM Configuration 4 S Data Log Change Password lt About EAGAR Load Save Conti Ss eas Ek ee pae Ferny am ae EN poco eee HHI YYYY EF Channel ate Format Sein Time oe ollection Frequency Buzzer pre CH EF Channel Changing the Time Format Note Update the system s Configuration Worksheets to document any changes Note The default time format is 24 HR To change the time format perform the following procedure Unlock the EA800 as shown eae og et Date in Locking and Unlockin Sensors p Set Time fae Ge an page 55 Relays D Configuration QJ Data Log Change Password D System H Update Firmware About EASHE Load Saue i ak RK 8 IE FURMIAT ate Forma Time Format Cd HE LV JIA A Set to Collection Eegen 12 Hl bh K EE Time Format Collection Frequency Buzzer el D EF Channel H 60 D 011 0152 Maintenance Changing the Date or Time Setting To change the date see Setting the Current Date on page 31 If your region uses Daylight Savings Time and you want the EA800 to display the correct time you must change the time setting manually when Daylight Savings T
70. nks Each wireless sensor is hard coded with an address the base unit uses to identify the sensors installed in the system When you program the system you assign each installed wireless sensor to a relay using its hard coded address Wireless sensors can be any of the following types e Wireless Humidity Sensor EA WHS e Wireless Temperature Sensor EA WTS e Wireless Multi Function Sensor EA WMFS Any of the following wired sensors can be connected to the wireless multi function sensor effectively converting the wired sensor to wireless e Low temperature sensors Blue Thermistor Probes e High temperature sensors Red Thermistor Probes e Ultra Low temperature sensors White Thermistor Probes e Water Bug sensor Supervised e Normally Open NO Contact e Normally Closed NC Contact Table 5 Sensor Temperature Sensors Part Number EA800 Compatible Temperature Sensors Description Table 5 lists the temperature sensors available for use with the EA800 Alarm System Operating Range Parameters High Temp Red Stainless Steel PN M 001 0081 Thermistor Stainless Steel Probe High Temperature Sensor 0 C to 150 C 32 F to 302 F Low Temp Blue Stainless Steel PN M 001 0082 Thermistor Stainless Steel Probe Low Temperature Sensor 50 C to 70 C 58 F to 158 F Low Temp Blue waterproof PN M 001 0086 Thermistor waterproof low tempera ture sensor For use in coolers an
71. nsor also allows you to configure an alarm delay time if desired 1 Unlock the base unit if necessary to continue programming See Accessing the MAIN MENU for Programming on page 28 2 Select SENSORS from the MAIN MENU and follow the steps in the following diagram 3 After you press the ENTER key the NEW WIRELESS SENSOR screen is displayed The EA800 searches for new wireless sensors indicated by an arrow that moves from left to right across the screen When an available wireless sensor has been detected it is listed in the SELECT SENSOR screen as shown below 4 Use the arrow keys to select the sensor to be configured then follow the prompts to configure all screens for that sensor as shown in the following diagram Example shown set values as appropriate for your system d E b fae Uer fl ed 5 Wiew Sensors Wireless Relays Replace RF Sensor Data Log gt Edit Sensor IOo d Se E E Sensor erforniance ES CANCEL RR EN BREE B er e a SEARCHING Relay S elay Relay Me E aaa a RN EN RRE ENER Hab Alarm mt ommon Hame Custom Hame aundry koom gt SCH Pump EA H Walue 99 Basement 8 Ge REPIS a geleet Deen EE T PREU T HERT Low Hlarm it TE l Enter Waluet FD Enter Walue H Bag EH F HCH PREW J HEAT CANCEL O O DOO O O ai a a E se el Sensor Sensor Added i SE E eplace ensor z Edit Senzor Delete Sensor Performance T C ee ee This is the start screen for
72. ogramming See Accessing the MAIN MENU for Programming on page 28 2 Select SENSORS from the MAIN MENU and follow the steps in the following diagram 3 After you press the ENTER key the NEW WIRELESS SENSOR screen is displayed The EA800 searches for new wireless sensors indicated by an arrow that moves from left to right across the screen When an available wireless sensor has been detected it is listed in the SELECT SENSOR screen as shown below Sensors iew Sensors Wireless Relays es KE Sensor d r p Neu Cie mea Los o ire a vhe ie e Data Log Edit Sensor System Delete Sensor About EASGE Fer formance MM C er ee a MEN WIRELESS SENSUR SERERER HHHHHHE 1 4 Use the arrow keys to select the wireless multifunction sensor to be configured then follow the prompts to configure all screens for that sensor Follow the procedure shown on the next page to add a temperature sensor The procedure shows a wired Blue temperature sensor but is applicable to the wired Red and White temperature sensors as well The Hysteresis setting helps prevent alarms from being set and reset continually if the environment is at or near the alarm set point by providing an acceptable variance For example if HYSTERESIS is set at 1 and the sensor High Alarm Limit is set at 158 the sensor reading must decrease to 157 157 minus 1 in order for the temperature alarm to reset to a no alarm condition D 011 0152 35 Adding Wireless Senso
73. omer Service at 1 800 635 4269 The information in this document has been carefully examined and is believed to be entirely reliable However no responsibility is assumed for inaccuracies EnviroAlert and the Winland logo are trademarks of Winland Electronics Inc in the U S Other product names and trademarks appearing in this manual are the property of their respective owners WINLAND ELECTRONICS INC Manufactured in the U S A by Winland Electronics 1950 Excel Drive Mankato MN 56001 Outside MN Phone 1 800 635 4269 Phone 507 625 7231 Fax 507 387 2488 Winland Electronics Inc 2008 www winland com D 011 0152 Rev A
74. ply to any of Winland s products which have been subject to misuse negligence or accident or which have been repaired or altered outside of Winland s factory Winland shall not be liable for loss damage or expense resulting directly or indirectly from the use of its products or any other cause THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY FITNESS FOR PARTICULAR PURPOSES NON INFRINGEMENT AND TITLE AND ANY WARRANTIES ARISING FROM COURSE OF DEALING USAGE OF TRADE OR OTHERWISE ALL OTHER REPRESENTATIONS MADE TO THE END USER PURCHASER BY ANY OTHER PARTY ARE ALSO EXCLUDED WINLAND SHALL NOT BE LIABLE TO ANY PERSON FOR INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY DESCRIPTION WHETHER ARISING OUT OF WARRANTY OR OTHER CONTRACT NEGLIGENCE OR OTHER TORT OR OTHERWISE Under no circumstances shall Winland s liability under this limited warranty exceed the purchase price paid by the end user purchaser for the product No person agent or dealer is authorized to give warranties on behalf of Winland nor to assume for Winland any other liability in connection with any of its products Duplication or distribution of this manual and any information contained within is strictly prohibited without the express written permission of Winland Electronics Inc To order additional copies of this manual or other related manuals contact Winland Electronics Cust
75. r or unreliable operation N CAUTION Connection of unsuitable loads to this connection may damage the power supply and EA800 base unit or result in improper or unreliable operation Note Do not apply power to the base unit until you are ready to begin sensor programming The base unit has a 30 minute timer that starts when the unit is first powered up If at least one sensor is not added and pro grammed within the 30 minute time period an alarm will occur 1 Using a terminal block adapter connect power supply and leads to POWER IN and on J5 Observe proper polarity If using a transformer ensure that the transformer is an isolated power supply 2 If Aux Power Out is to be used connect and leads to AUX POWER OUT and on J5 using a terminal block adapter Install the Wireless Sensors If the EA800 base unit will be connected to a remote alarm panel do not connect N CAUTION l eae the base unit to the alarm panel until after sensor connection and configuration is complete Connecting the remote alarm panel before configuring the EA800 sensors will result in false alarms at the remote panel 22 D 011 0152 Installation Note Verify that the wireless sensors can communicate with the base unit as outlined in the following proce dure before permanently mounting them 1 Remove the cover from the wireless sensors and record the MAC addresses see Figure 12 of each wireless sensor on the Configuration Wo
76. reless sensors have been added to the system all wireless sensors must be reset GT EE o __ SE EAH MEL ate Forma 5 Time Format c Set to Collection Frequency cH gt 1 Buzzer 19 vio RF Channel d 18 ei WISEN e n ee ee ee Choose appropriate setting tn ate Forma Time Format Set Time Collection Frequency gt H Confilauration D Buzzer Change Password G EF Channel ad Update Firmware Load Save Conti PRETT a E 9 Press F3 to confirm your selection When the CONFIGURATION menu is displayed press F1 to return to the MAIN MENU You have configured the EA800 system settings Proceed to the next section to set the time and date 30 D 011 0152 Installation Setting the Current Date Unlock the EA800 to continue programming if necessary See Accessing the MAIN MENU for Programming on page 28 From the MAIN MENU use the arrow keys to select SYSTEM then select Set Date and set the current date as shown below Note Togo back or to skip a step press the PREV F2 or NEXT F3 keys To cancel press F1 ee Example shown set values as 5 d r pa ei EE 19 appropriate for your system Sensors ensors deta tats bo ata Lo The chy H System E About EASHE About EASGE PaaS Bee ES eee et Date H WE A v onfiauration a Enter Year 2887 Aaly Update Firmware CAAT to 210A Load Sawe nee ee eee Enter Month 12 to 123 DEER Enter Day 19 1 to 31 gt Ee WE A OHTE Set to 12 19 2H87
77. rksheet you completed during the preparation phase The MAC address is printed on a label affixed to each wireless sensor s printed circuit board PCB and is used to identify each sensor during programming 2 Temporarily mount the front panel of the base BESSER unit to the mounted rear panel MAC Address Label 3 Connect power to the EA800 The EA800 SENSOR MODEL NO completes its boot process and the MONITORING Example EA WTS Wireless Temperature Sensor or NO SENSORS INSTALLED if there are currently no wireless sensors installed screen is displayed Figure 12 Wireless Sensor MAC Address Location 4 With the wireless sensors located near the base unit connect power to each wireless sensor 5 Unlock the keypad and allow the base unit to detect the wireless sensors using the following procedure Note The keypad locks automatically after 30 minutes of inactivity no key presses If you have not finished the detection and programming process for a sensor and this occurs entered values are lost and you must start the programming procedure for the sensor from the beginning It is recommended that you allow the base unit to identify the wireless sensors one at a time with the sensors unmounted and in the same location as the base unit Example shown set values as Enter appropriate for your system 0800 WII EU EA EA BRUN WUER Aly DOr 36 nter Password BEBE eine arm Log ET Sa E op Aer Cie 4 E D KE H p Gi E elaus elaus
78. rol of AC mains powered loads Additionally local codes may further dictate or limit the types of loads and associated wiring to be used with the low current Form C relay outputs used with the EA800 Connecting AC mains type circuits to the EA800 may result in an electric shock and or fire hazard N CAUTION Do not connect a load to the AUX OUT or OUTPUT 1 through OUTPUT 8 relay outputs that exceeds limitations stated in the Specifications section of this manual Loads exceeding the specified limitations may damage the EA800 or result in improper or unreliable operation 8 Using the floor plan you created identify the specific locations for each sensor and verify that their locations meet the specifications See Specifications for operational parameters such as cable length Note For 4 20mA sensors See 4 20mA Sensors for a discussion of determining the constraints for your 4 20mA sensor to ensure accuracy over its rated range 9 Determine the channel to use for the wireless sensors If more than one EA800 is being installed on site it is recommended that they be configured to use different channels 10 The wireless sensor must be located so that the wireless signal strength is adequate as outlined in Winland Application Note AN00101 You must verify that the wireless sensors can communicate with the base unit before you permanently mount them Note Certain environments may present conditions that intermittently cause interference with
79. rs 1 Make certain the sensor s wiring is passed through the opening in the mounting plate Installation 2 Remove the adapter from the correct input connector headers by pulling the adapter up and off of the circuit board header connectors 3 Strip the ends of each of the sensor s wires as indicated by the gauge on adapter you just removed 4 Insert the stripped wire ends into screw terminals of the adapter as indicated by your EA800 Wiring Diagram you completed in the preparation phase Observe proper polarity See Figure 15 Base Unit Powered EA800 Base Unit J5 J6 Aux Power Out Input N User supplied lt a cable SOURCE Q UN W i O oO HA III Connector External Power Adapter External Adapter Powered EA800 Base Unit J5 J6 Aux Power Out Input N SOURCE Q 2 eb O A HA III Connector Figure 15 EA800 Base Unit Wired HA IIl Sensor Connections 5 Secure the connections using the setscrews on the adapter Check the connection by lightly pulling on each connection 6 After connecting the wire ends to the adapter align the adapter to the correct header pins as indicated by your EA800 Wiring Diagram and press the adapter fully onto the header connector pins D 011 0152 25 Connecting Wired 4 20mA Sensors Connecting Wired 4 20mA Sensors 1 Make certain the sensor s wiring is passed through the opening in the mounting plate 2 Remove
80. rs When setting numeric values use the arrow keys to change the value Use the PREV and NEXT soft keys to move the cursor to the next or previous digit Press the ENTER key to enter the value Example shown set values as appropriate for your system Harn i b op RE Zeng a b Mirad a o i pee palates Wireless elaus eplace ensor Data Log Wees Edit Sensor System Delete Sensor About EASHH Fer formance T Die nodi eenegen 6 ne AE E t man D fi Saba Ser Custom Hame enor ite Sensor 4 ek HH III eet CO Eet Re ee Jo o OOO O ee re Jo OO O E re E A Miah Hlarm Limit EE i C oler Cooler 3 Enter Walue 7158 Peezer Freezer 2 T Low Alarm Limit Fam mg AU BUS EK SEL elAle D I l Enter Walue 886 Enter Waluet 955 ES e LDHLEL PREY HEAT LDHLEL FREU NEST ee ET a Sensor Added EP eel This is the start screen for the next Replace RF Sensor sensor to be added if any Edit Sensor Delete Sensor Performance T a 36 D 011 0152 Installation Adding a Wireless Humidity Sensor The Hysteresis setting helps prevent alarms from being set and reset continually if the environment is at or near the alarm set point by providing an acceptable variance For example if HYSTERESIS is set at 1 and the sensor High Alarm Limit is set at 95 the sensor reading must decrease to 94 95 minus 1 in order for the humidity alarm condition to reset to a no alarm condition The humidity se
81. rs will result in false alarms at the remote panel The suggested preparation procedure is as follows 1 Read and understand the entire manual General Information provides important information required to properly plan install and use the EA800 The preparation phase helps ensure that the EA800 system will function as required 2 Photocopy the pages of Appendix B Planning Worksheet Appendix C EA800 Wiring Diagram one for each EA800 base unit in the system and Appendix D System Configuration Record to create a record of the specific EA800 alarm system installation you are currently working on 3 Draw a floor plan for the facility where you will install the EA800 alarm system Identify important details such as the coolers doors computer rooms etc An example is shown below Cooler1 Storage Room 3 Rear ger panel Entry installation area Front Entry Front Desk Conference Room Men s Room Freezer 1 Freezer 2 Room 1 Room 2 Women s Room Figure 8 Example Floor Plan 4 Locate the base unit where authorized personnel can readily access it If required consideration should be made regarding a location that discourages unauthorized access If using wireless sensors locate the base unit to minimize the wireless distance Ensure that the desired mounting locations for the EA800 base unit and each sensor comply with the environmental specifications listed in Table 13 Specifications AN CAUTION Do not in
82. rsrnrrrnrrnnrrsrersrrnnnne 33 Adding a Wireless Multi Function Sensor Using a Wired Temperature Sensor a n000n00n000na 35 Adding a Wireless Humidity Gensor 37 Adding a Wireless Multi Function Sensor Using a Wired WaterBug Gensor 38 Adding a Wireless Multi Function Sensor Using a Wired Contact Closure Gensor 40 Verify Wireless Signal Strength EN 42 AGNO We E 43 Adding a Wired Temperature Sensor s nnenneennesreosrrnsrrrsrrrstrrsrnrnrnrrrrrrsrrrsrrrstrrtrrtrerrersrrrn nni 43 Adding a Wired HA IIl e tele e EE E 44 Adding a Wired WaterBug Sensor n nsennnennnenensrrnsrrsrrrrrrrrrrrrrrrrsrrrsrrrrrrrrrtrrntnrrtnresrernrenn nne 45 Adding a Wired Contact Closure ne 46 Adding a 4 20MA SENSOT E 47 CORNUTO TNE E 48 D N11 N152 i SE AUN ODN aaa cesses eats parte tn eerstcs E E 49 Monitoring Environmental Conditions EE 49 Vetrieder 50 VS WING ACIYS AII aeee a E e e a 50 Viewing the Alarm Log 51 Viewing Pending Alarm Information ET 51 Viewing Limit Settings E 52 VIOWINO 1NG EVON CO E 52 Viewing THE SO LO E 53 Viewing Fiimware Information EE 53 VIEWING lee Ee sag cioteanitase Serres eedon ago tnecsan tat ne ciraseauetameatnaanhancte Lich eopewtameataanaiiale chanetoinnSstaaatueniatenie ths 54 MAIME TA INC Sec pececnencssmeereetecwecteensenensneeuueuserinesswsanaceeswonanaesseeacesencnsceewn oseeeetacsiieeneisenateeeudescuneveatceniensuea son 55 Locking and Unlocking the EA80O0 ME 55 Pausing Monitoring and Cancelling TE 56 e
83. rt LAMLEL Sai To return to Remove USB drive when LOAD SAVE CONFIG screen export is complete DEAR i ees 1 C 20 cfg To return to the home TI TI DE E SE Now that the configuration is stored on the USB drive you should copy it onto a PC to provide a backup in the event that the USB drive is lost or fails By default the configuration file is named EAYYMMDD HHMMSS cfg where m EA indicates that the configuration file is from the EA800 E YYMMDD is the current date E HHMMSS is the current time in 24 hour format It is suggested that you rename saved configuration files to identify the specific EA800 system they came from using up to 15 characters not including the file extension CFG File names longer than 15 characters are not Supported 66 D 011 0152 Maintenance Loading Configuration Settings You can load configuration settings from a previously installed EA800 to serve as the template for the system being installed or updated To load a configuration from a USB drive insert the USB drive into the USB port and perform the following procedure Unlock the EA800 as shown in Locking and Unlocking as ee the EA800 on page 55 censors Set Time Relays Configuration Data Log Change Password G System d Update Firmware About EASE Loads Sane on i SS SSS ees Save Config Bone wees This message appears only if no USB drive is present f i Insert USE Drive Select the configuration
84. s Sensor Sensor Physical Model Name Location Parameter Settings Resolution Operational Parameters Low Scaled Value High Scaled Value Hysteresis Low Alarm Limit High Alarm Limit Alarm Delay Time No Alarm Relay State Active Condition Sensor 5 Settings wireless Sensor Sensor Physical Model Name Location Parameter Settings Resolution Operational Parameters Low Scaled Value High Scaled Value Hysteresis Low Alarm Limit Installed LQI in bars High Alarm Limit MAC Address Alarm Delay Time Notes No Alarm Relay State Active Condition D 011 0152 89 EA800 Environmental Alarm System Configuration Form Sensor 6 Settings wireless Sensor Sensor Physical Model Name Location Parameter Settings Resolution Operational Parameters Low Scaled Value High Scaled Value Hysteresis Low Alarm Limit Installed LQI in bars High Alarm Limit MAC Address Alarm Delay Time Notes No Alarm Relay State Active Condition Sensor 7 Settings wireless Sensor Sensor Physical Model Name Location Parameter Settings Resolution Operational Parameters Low Scaled Value High Scaled Value Hysteresis Low Alarm Limit Installed LQI in bars High Alarm Limit MAC Address Alarm Delay Time Notes No Alarm Relay State Active Condition Sensor 8 Settings wireless 90 D 011 0152 EA800 Environmental Alarm System Configuration Form
85. s follows IE g i OPTS Time Format Collection Frequency Buzzer EF Channel J E EH LE FURMAT c4 HR Set to 12 AMF Se a Saas Choose setting for your region 6 Press F3 to confirm your selection When the CONFIGURATION menu is displayed select and set COLLECTION FREQUENCY as shown below Collection Frequency determines how often the base unit collects data from the sensors D 011 0152 29 Programming Gn Sales _ ee ey PS LULLEC TION FREWUEML Y KA ate Forma econds y Time Format 1 Minute Set to D BEER Frequency H a D E H Minutes Uz zer nutes ES EF Channel te ee nutes PRETT Lo II DK Choose appropriate setting 7 Press F3 to confirm your selection When the CONFIGURATION menu is displayed select and set BUZZER as shown below The BUZZER setting enables disables the audible alarm buzzer Selecting DISABLED for this parameter turns the audible alarm buzzer off completely No audible alarm tone will sound when an alarm occurs if DISABLED is selected i SAE as KA IE p rare Time Format ae o ea Frequency q H Geet e SC Gan Uzzer ei EF Channel WIR RN BM eS a KT Choose appropriate setting 8 Press F3 to confirm your selection When the CONFIGURATION menu is displayed select and set RF CHANNEL as shown below The RF CHANNEL setting determines the RF frequency at which the wireless sensor s and base station communicate Note f the RF channel is changed after one or more wi
86. s B Product Compliance Statement per CFR 15 105 b VSSEA WS 031108 NOTE This equipment has been tested and found to comply with the limits for a e IC 7635A EAWS Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications However there is no guarantee that interfer ence will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help The TUV certification combines electrical safety certification for Canada SCC United States NRTL and Europe EU Directives This product was voluntarily tested according to the relevant safety requirements and mentioned properties pertaining to this certification mark The product is in confor
87. s what is assigned to the Auxiliary Relay To change the buzzer setting perform the following procedure SE SC pit e SC Sensors Fel K ge in Locking and Unlocking EI elaus D Configuration H the EA800 on page 55 Data Log LS Change Password System d Ka Update Firmware lt About EASHH Load Sawe Conti SS fa ee O 00O ee hor ale See n Collection Frequency 2 ete RF Channel IE z OPTS EAE ED Coll E Ze GC pr Deen Te EF Channel IT KT a ee 62 D 011 0152 Maintenance Changing the Password Note Update the system s Configuration Worksheets to document any changes Note f you do not enter a valid password you will not be allowed to change the selected password The default password 0800 cannot be changed or deleted One user configurable password may be set in addition to the default 0800 password To set or change the user configurable password perform the following procedure Jee K E ei R Unlock the EA800 as shown Sensors Set Time in Locking and Unlocking Relays Configuration the EA800 on page 55 Data Log cr H Change Password H DG System al Update Firmware About EXSHE Loads Sawe on Enter Present Password HSHH Use NEXT key to advance the CAHHMLEL PREW HEST cursor to the next digit then use the arrow keys to set the value Lnange Hamin Hew Password Password Changed a r dE WE onfiguration DH Change Password H t Update Firmware Load Sawe Confi Gi
88. sed contacts m Temperature from 80 C to 150 C 112 F to 302 F E Humidity from 5 to 95 RH non condensing m Presence of water m Any sensor with a 4 20mA interface The EA800 base unit may be mounted directly to a 3 gang electrical enclosure or to walls The wireless sensors are easily mounted to the wall Figure 1 shows the base unit and a wireless sensor ENVIROALERT lt I Figure 1 EnviroAlert EA800 Base Unit and Optional Wireless Sensor D 011 0152 1 How to Use This Manual How to Use This Manual This manual is organized into sections that guide you through the installation process then describe how to use the EA800 and change its programmed settings if necessary Some troubleshooting guidelines are provided and the appendices contain forms for you to photocopy and use to record the programmed settings of the EA800 and the monitoring system setup The manual presents EA800 programming procedures by showing you the sequence of menus and screens you will see as you perform the procedure and the keys to press to advance to the next screen The example below is the procedure for unlocking the EA800 base unit to allow programming Step 1 Press the Step 2 The UNLOCK screen Step 3 Press the F1 can be pressed at this time F1 soft key is displayed Enter your ENTER key to lock the unit password using the arrow keys HECKER Ale TICE 9 L TH F FIR Enter Password HERR ES TH F a 3 69 F a lt 5 A ES F
89. ss sensor repeat this procedure 8 If you are finished performing sensor maintenance press to exit maintenance and resume monitoring 9 Press F1 to lock the keypad Editing Sensor Parameters The general procedure for editing sensor parameters is provided below Not all sensor parameters can be edited for an installed sensor The editable parameters are dependent on the installed sensor so the EDIT SENSOR screen varies according to the sensor selected You cannot edit the following m The low and high scaled values for a 4 20mA sensor If these require changes you must delete the 4 20mA sensor and re add it to the system See Connecting Wired HA IIIl Humidity Sensors on page 25 m Asensor s type For example if a 4 20mA sensor was incorrectly added as a Blue temperature sensor you must delete the incorrect sensor and then re add the correct sensor m The unit of measure If unit of measure must be changed the sensor must be deleted and re added to the system Note Unlock the EA800 as shown in Locking and Update the system s Configuration Worksheets to document changes D PEN ee Sensors iew Sensors Unlocking the EA800 on Ae ae Sensor q ata Log it Sensor Bade System Delete Sensor About EASE Performance MM gh Alarm Limit Ts AE 8 TAR 1 Cooler 2 R PHE Ae i High Alarm Limit Seep ile nter Waluei KA Low Alarm Limit VW Laundry Room lt Hysteresis lt lt oie EI Alar
90. ssage appears HO DENICE INSERTED insert the USB drive with new firmware into the USB Insert USE Drive port LHMLEEL a Note PLHMLEL oT LURE PORTE Overwrite ul GC with k1ZFLU 1 UFD ut dt ee ee J OEO Remove USB drive when Pl Cplus upd update is complete FEMONE USE DRIE FFES5 OK TO REBOOT ee O O K D 011 0152 NETT fas cat Ti g et Time Confilauration Change Password Update Firmware H aH oad sane Conti KLS GEES During the process the UPDATING FLASH screen is displayed The file name is limited to 15 characters or less not includ ing the file extension UPD File names greater than 15 characters are not supported and will not be displayed on the E AGO The EA800 reboots with the new firmware 65 Saving Configuration Settings Saving Configuration Settings You can export the configuration settings from the EA800 to serve as an archive for the system or as a template for quickly programming other systems The configuration data is stored in a machine readable format To export configuration to a USB drive perform the following procedure d r BF T E a Unlock as shown in Locking Sensors Set Time and Unlocking the EA800 Relays Configuration Data Lo Change Password SE H System H Update Firmware About EASHE i Load Saue a ak H A a ad tonta SC fortis KA deene If this message appears insert the USB drive with the configuration into the Insert USE Drive USB po
91. stall the EA800 base unit in coolers or freezers Use only wired sensors specified in this manual for the INPUT 1 through INPUT 4 N CAUTION hon connections Unverified sensors may damage the EA800 or result in improper or unreliable operation D 011 0152 17 5 Complete the copy of Appendix B Planning Worksheet for the facility in which the EA800 system is to be installed This must include all monitored areas for the total security system so that you Know how many EA800 base units are needed 6 Determine the sensors required from the Planning Worksheet you completed and the information provided for each sensor type in System Configuration Enter these in the copy of the System Configuration Record you made Note When water sensors are required you must use at least one supervised water sensor and may add up to five additional unsupervised water sensors all in parallel Thus an alarm on any sensor will result in an alarm with no way to determine which sensor is the source 7 Enter the sensor information in the copy of the EA800 Wiring Diagram you made It is a good idea to name each sensor on this diagram and use that name in both the EA800 Wiring Diagram and the System Configuration Record This helps ensure proper programming of the system after you have physically installed the system DANG cee EA800 relay outputs are intended only for use as low voltage low current alarm connections and not for direct switching or cont
92. sure Sensor Wireless multi function sensors are physically connected to wired sensors located elsewhere and provide a transmitter to send the signals monitored by the wired sensor to the base unit To add a wireless multi function sensor do the following 1 Unlock the base unit if necessary to continue programming See Accessing the MAIN MENU for Programming on page 28 2 Select SENSORS from the MAIN MENU and follow the steps in the following diagram 3 After you press the ENTER key the NEW WIRELESS SENSOR screen is displayed The EA800 searches for new wireless sensors indicated by an arrow that moves from left to right across the screen When an available wireless sensor has been detected it is listed in the SELECT SENSOR screen as shown below Sensors Wiew Sensors Wireless Relays Replace RF Sensor d r pa a dvi E E Ae rien mea Lol z e e Data Log Edit Sensor System Delete Sensor About EASHH Ferformance MM EIN a S Lee MEN WIRELESS SENSUR SEARCHING Ke AMER 4 Use the arrow keys to select the wireless multifunction sensor to be configured then follow the prompts to configure all screens for that sensor To add a wireless multi function contact closure sensor to the system perform the following procedure The procedure shown is for a normally open N O contact closure sensor but is essentially the same for the N C wireless contact closure sensor 1 Unlock the base unit if necessary to continue programm
93. t Adjust Range is dependent upon the sensor being used See Accessories on page 44 Water Presence No Alarm Alarm Sensors Up to four wired sensors Up to four wireless sensors Cable Length to Wireless Multi Function Sensor EA WMFS 100 ft maximum Wired Temperature Sensor 2 wire maximum 304 m 1000 ft cabling length Wired Humidity Sensor D 011 0152 3 wire maximum 304 m 1000 ft cabling length 73 Accessories Table 14 Specifications continued Wired Water Presence Sensor Specification 2 wire maximum 304 m 1000 ft cabling length Wired 4 20mA Sensor EA800 load 160 Ohms maximum Relay Outputs 9 Form C with 3 terminal NC COM NO connections Note There are 8 primary relays 1 dedicated for each sensor and 1 auxiliary relay Relay Contact Ratings Max 30VDC 1 amp resistive Not for use with AC power Relay Logic Each relay is user configurable Display 128x64 graphic LCD with blue backlight Device Environmental Operating Range Humidity 5 to 95 RH non condensing Temperature Operating 0 C to 50 C 82 F to 122 F Not for installation inside coolers or freezers Ambient Environmental Quality Indoor use intended non corrosive environment Conformity Certifications FCC Part 15 Subpart C Class B ICES 003 Issue 3 1997 NRTL CUE certification mark Warranty Two 2 Ye
94. t or near the alarm set point by providing an acceptable variance For example if HYSTERESIS is set at 1 and the sensor High Alarm Limit is set at 158 the sensor reading must decrease to 157 158 minus 1 in order for the alarm condition to reset to a no alarm condition Example shown set Ca VR values as appropriate for f Ge WEI Lat A ela your system HABE kelay 6 34 SE b Ewen Dr fi SCH H R fi Custom Hame KA Al SE WE Ki A Ke ooler ee Cooler 4 lt Freesen k Freezer 2 T LHNLEL a L 1 d Enter Walue 158 Enter Walue RIDE Z SSS Li E 5 LHNLEL FRES MEST LHNLEL FRES HEAT LHNLEI E PO SENSOR HUDED Pb bensr Sensor Added y Wiew Sensors Enter Walue H Replace RF Sensor Edit Sensor Delete Sensor Fer formance L LHNLEL HELI HEAT CO F3 Note Repeat this sensor for each wireless temperature sensor you need to program When you have finished programming wireless temperature sensors proceed to the section appropriate for the other types of wireless sensors to be added D 011 0152 Installation Adding a Wireless Multi Function Sensor Using a Wired Temperature Sensor Wireless multi function sensors are physically connected to wired sensors located elsewhere and provide a transmitter to send the signals monitored by the wired sensor to the base unit To add a wireless multi function sensor do the following 1 Unlock the base unit if necessary to continue pr
95. te OA D 011 0152 63 Clearing the Alarm Log Clearing the Alarm Log To clear all stored alarm records perform the following procedure Note You cannot clear the Event Log ee EF et H Sensors Wiew Alarm Log Unlock the EA800 as shown in Locking and Unlocking the EA800 Relays gt Wiew Sensor Log on page 55 L Data Log H Export All Logs System G Clear Alarm Log H About ERHGRR Clear Sensor See E EEE Ee BALE ER ALARM LU HH LUG LLEHRED lew Event Log ic boa A e iew Sensor Log PE geen GE Export All Logs CH G Clear Alarm Log H lear Sensor See PLAMLEL TEST E EE O BALE JO Clearing the Sensor Log 64 To clear all stored sensor records perform the following procedure Note You cannot clear the Event Log ETT ne ue or Sensors Hiem Alarm Loo Unlock the EA800 as shown in Locking and Unlocking the EA800 Relays Ge liem Sensor Log ine a isie n ee Abat EASHE WEE Sensor A D Sa Eas TEEN SENSUR LU Se ee uk L Event Log A Kegel me Pe YOU Sure gt iew Sensor Log Export All Logs CH Clear Alarm Log Clear Sensor Lo D 011 0152 Updating the Firmware Maintenance Download the latest firmware from www winland com to your computer then save it to a USB jump drive before performing the procedure for updating the firmware as shown below Unlock as shown in Locking and Unlocking the EA800 i on page 55 e 8 US Leit i About EASHH A If this me
96. tem Block Diagram Example D 011 0152 3 Symbols on the Product or Manual Labeling Symbols on the Product or Manual Labeling Symbols appearing on the product labeling packaging and or in this manual are shown and described in Table 1 Table 1 Symbols on Product or Manual Symbol Definition Attention consult accompanying documents or statements For product disposal ensure the following e Do not dispose of this product as unsorted municipal waste e Collect this product separately Lo RoHS WEEE e Use collection and return systems available to you Indicates product complies with ROHS WEEE directive COMPLIANT NO Normally Open NO relay contact terminal NC Normally Closed NC relay contact terminal C Common relay contact terminal AUX Combined single pole double throw SPDT NO relay output that activates upon an alarm from any of the sensors Model EA800 This device complies with part 15 of the FCC Rules Operation is subject to the follow e FCC ID ing two conditions 1 This device may not cause harmful interference and 2 this V5SEA800 031108 device must accept any interference received including interference that may cause e IC 7635A EA800 undesired operation Caution Statement per CFR 15 21 Models EA WMFS Changes or modifications not expressly approved by the party responsible for compli EA WTS EA WHS ance could void the user s authority to operate the equipment e FCC ID Clas
97. the EA800 is ready for programming The following is an overview of the general process for programming the EA800 View the MAIN MENU and unlock the EA800 as described in Accessing the MAIN MENU for Programming on page 28 Set the system configuration as described in Configuring System Parameter Settings on page 28 Set the current date as described in Setting the Current Date on page 31 Set the current time as described in Setting the Time on page 32 Add the wireless sensors See the appropriate subsection under Adding Wireless Sensors on page 33 Add the wired sensors See the appropriate subsection under Adding Wired Sensors on page 43 Verify performance of the wireless sensors See Verify Wireless Signal Strength on page 42 Configure the relays See Configuring the Relays on page 48 N CAUTION If the EA800 base unit will be connected to a remote alarm panel do not connect the base unit to the alarm panel until after sensor connection and configuration is complete Connecting the remote alarm panel before configuring the EA800 sensors will result in false alarms at the remote panel Note When no sensors are programmed in the EA800 system the EA800 base unit boots up with a 30 minute delay before the alarm buzzer sounds At this time the Alarm screen is displayed with a System Alarm caused by the fact that no sensors have been programmed yet To prevent the System Alarm from going off
98. the mounting plate from the base unit by disengaging the mounting plate hinges from the mating tabs on the base unit D 011 0152 21 Install the Wired Sensors 2 Mount the mounting plate as follows m Mounting to 3 gang enclosure Use four 4 machine screws to secure the mounting plate to the mating holes in the 3 gang enclosure WR Mounting to drywall surface Place the mounting plate in mounting position Mark the four mounting hole locations Install drywall anchors and secure the mounting plate to the anchors Note f wall mounted prepare a wiring access hole at this time All wiring must pass through the opening in the center of mounting plate Install the Wired Sensors Install the wired sensors in accordance with the instructions provided with the wired sensors 1 Mount each wired sensor in its designated location 2 Label each sensor s wires for easy identification 3 Route the wires from the sensor to the base unit and dress the wires as required by local code It is important to ensure that the wires are protected along their entire length are not stressed at any point and are adequately supported along their entire length 4 Pass the wires through the mounted EA800 rear panel EA800 Base Unit Power Connections N CAUTION Do not connect or disconnect power sensor or alarm wiring while power is applied Connecting and disconnecting the EA800 base unit with power connected may damage the base unit or result in imprope
99. to 12 Hours eS NM Enter Hour 2H CA to 23 Hours LAMLEL FREU esl See Figure 25 i IE z rare fi Time Format Enter Minute 33 Collection Frequency l Buzzer CA to 59 Minutes EF Channel LAML Enter Second 23 CA to 59 Seconds CAHE J Set tot 15 33 23 yerwrite ul Ge Wi F12FLU 1 UFD ut 2d CONFIGURATION SAUED ri zplus upd b ERGT1225 1r5439 c 9 RFEMOWE USE ORILE PRESS OF TO REBOOT Figure 24 System Screen Map D 011 0152 81 p IE E T 4 Time Format Collection Frequency Buzzer EF Channel DL rr Set to Set to D te a T 12 AMPA Minutes IT ET TI IK II IK TT DHTEEOKIRT MIE FURMIHT Set tot Set tot Moe yy c4H a ee ee ee ee OO OE me Tt SHELLED EMAELEO Set tot DISABLED Set to EHAELED Figure 25 Configuration Screen Map 82 D 011 0152 Appendix B Planning Worksheet Appendix B Planning Worksheet Note Photocopy and complete a copy of this worksheet for each system Installation Environmental Condition to Room Monitor Acceptable Condition Range Alarm Condition D 011 0152 83 84 D 011 0152 Appendix C Wiring Diagram Wiring Diagram Appendix C Note Photocopy and complete copy of this diagram for each EA800 to be installed in the system UOI O9UUOD jaueg wey uoneubiseq AOJOD AIM L Indjno Z ndino e indjno v Ndo S mdumc 9 mdumc A dm g mdumc 008V gt L yndu Z yndu ndul t md
100. u uoleubiseg AOJOD M UOI D UUO josues 85 D 011 0152 86 D 011 0152 Appendix D System Configuration Record Appendix D System Configuration Record Note Photocopy this appendix and complete a copy for each EA800 base unit in the system EA800 Environmental Alarm System Configuration Form Collection Frequency Date Format MM DD YYYY or DD MM YYYY 30s 1min 5 min 15 min 30 min 60 min Channel 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Time Format 12 hour or 24 hour 25 26 Buzzer Enabled or Disabled Sensor 1 Settings Sensor Sensor Physical Model Name Location Parameter Settings Operational Parameters Low Scaled Value D 011 0152 87 EA800 Environmental Alarm System Configuration Form Sensor 2 Settings Sensor Sensor Physical Model Name Location Parameter Settings Resolution Operational Parameters Low Scaled Value High Scaled Value Hysteresis Low Alarm Limit High Alarm Limit Alarm Delay Time No Alarm Relay State Active Condition Sensor 3 Settings Sensor Sensor Physical Model Name Location Parameter Setting Operational Parameters Resolution Low Scaled Value High Scaled Value Hysteresis Low Alarm Limit High Alarm Limit Alarm Delay Time No Alarm Relay State Active Condition 88 D 011 0152 Appendix D System Configuration Record EA800 Environmental Alarm System Configuration Form Sensor 4 Setting
101. uration is complete Connecting the remote alarm panel before configuring the EA800 sensors will result in false alarms at the remote panel Adding a Wireless Temperature Sensor 1 4 Unlock the base unit if necessary to continue programming See Accessing the MAIN MENU for Programming on page 28 Select SENSORS from the MAIN MENU and follow the steps in the following diagram After you press the ENTER key the NEW WIRELESS SENSOR screen is displayed The EA800 searches for new wireless sensors indicated by an arrow that moves from left to right across the screen When an available wireless sensor has been detected it is listed in the SELECT SENSOR screen as shown below TAC kd EC Wiew Sensors Tat Replace RF Sensor en v Eea Edit Sensor System Delete Sensor About EASHH Ferformance E TECH Ee HEN WIRELESS SENSUR SEARCHING p HHHHHHE Confirm that all new unprogrammed wireless sensors are displayed on the SELECT SENSOR screen use the arrow keys to select the sensor to be configured then follow the prompts to configure all screens for that sensor D 011 0152 33 Adding Wireless Sensors Note To enter numeric values use the arrow keys To advance the cursor to the next digit when entering numeric values press the NEXT soft key F3 To return to a previous digit press the PREV soft key F2 The Hysteresis setting helps prevent alarms from being set and reset continually if the environment is a
102. y be blocked or reflected by metal before they reach the alarm receiver Even if the signal path has been recently checked during a weekly test blockage can occur if a metal object is moved into the path Even if the system responds to the emergency as intended and is a monitored alarm system the authorities may not respond appropriately This equipment like other electrical devices is subject to component failure The most common cause of an alarm system not functioning properly is due to inadequate maintenance Your alarm system should be tested weekly to make sure all detection devices are operating properly Your control panel and keypads should be tested as well Installing an alarm system may make you eligible for lower insurance rates but an alarm system is not a substitute for insurance Homeowners property owners and renters should continue to insure their lives and property Table of Contents OME Fall MTOR AUS EE 1 EE 1 PLOW tO USE TMS Manders ace aah aut nie cate ointa ciate teen ge aay EPRIN en AEn REEE EEREN EIEEE NEEN EEEE 2 BOCK DIAT NS i E E E E E E E E 3 Symbols on the Product or Manual Labeling WT 4 VIONKONDO CPCI G eas A O 5 Eltere 6 EE EE 7 ACCESS Control and SSW ONG sates ac sttaore sasetcnsercnancuadenresss erasers EEr inetd E EEE 8 System Configuration en 9 eO eegene 10 Temperature Sensors geet 10 FMI CU SUNG ONS scars peace erste ee erent aan EE E A ede pavansiemeseeccenteeeoads 11 4 Q2OMA Sensors cess eese
103. you made See System Configuration for a description of each system level parameter When you have completed the previous steps you are ready to proceed to physically install the EA800 base unit and its associated sensors using the documentation you have just created D 011 0152 Installation Tools and Supplies Required Ensure that you have the following prior to starting the installation Phillips Screwdriver Mounting hardware for the EA800 base unit and any optional sensor units If required a drill and the appropriate drill bits Wire stripper Sensors not supplied see Accessories on page 54 Sensor Wiring typically 18 22 AWG twisted pair not supplied Alarm Wiring typically 18 22 AWG see EA800 Output Alarm Connections Power sources Power Requirements All power terminals must be connected to a Class 2 power limited circuit complying with the National Electric Code NFPA 70 Article 725 Where required this equipment is to be isolated from the mains supply by a limited power source as specified in EN60950 i EA800 relay outputs are intended only for use as low voltage low current alarm connections and not for direct switching or control of AC mains powered loads Additionally local codes may further dictate or limit the types of loads and associated wiring to be used with the low current Form C relay outputs used with the EA800 Connecting AC mains type circuits to the EA800 may result in an electric shock a

Enviro EA800 Home Security System User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents