EMC 014003051-00 Server User Manual
Contents
1. 9 Refer to the P4700 Quick Start Guide and the IP4700 Installation and Service Guide to ensure that the system is properly cabled for the IP4700 Figure 1 shows a sample configuration with three DAEs above the IP4700 DPE LNA 1 Fibre Channel Fibre Channel Management LAN LAN Rear of cabinet Storage processor A Storage processor B to standby power supply A to standby power supply B interface interface EMC1485 Example IP4700 Configuration Three DAEs Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Loading IP4700 Software Loading IP4700 Software The steps in this section guide you through the firmware software loading process They begin with verifying and if necessary flashing new firmware to each storage processor You must follow the remaining steps in the exact order listed They describe how to load an IP4700 software image from the hard drive in your conversion kit seed disk to the system Locate the IP4700 seed disk P N 005047310 in your conversion kit and have it available before you begin this procedure 1 Connect a Windows console to SP A through the serial port as shown in Step 3 of the P4700 Quick Start Guide 2 Start a HyperTerminal session 3 If necessary turn on ac cabinet power to the side that powers SPS A then to the side that powers SPS B Turn the SPS A power switc2. CLARalert IP Installation Checklist CLAR PSP 003 Rev C EMC Email Installation Checklist CLAR PSP 004 Rev B EMC CLARalert IP Release Notes 085600442 CLARalert IP Install Guide 069701171 Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Converting the Hardware Converting the Hardware A CAUTION The following procedure assumes that you have appropriately backed up or moved to another storage system any data you want to preserve Once you begin the conversion procedure you CANNOT RECOVER ANY DATA from the FC4700 storage system In addition to this guide you will need the instructions in the P4700 Quick Start Guide and the IP4700 Installation and Service Guide Locate those documents and have them available before you begin the conversion procedure To convert your hardware from an FC4700 to an IP4700 follow these steps Exchange Storage Processors and System Drives 1 Power down the system as described in Chapter 2 of the IP4700 Installation and Service Guide 2 Reconfigure the rack components if required a Remove Fibre Channel switches the IP4700 does not support Fibre Channel switches b Reposition DPE DAEs as required Set your DAE IDs in sequential order Refer to your DAE documentation and the description of Addressing Requirements in Chapter 2 of the IP4700 Installation and Service Guide c Position disks in the enclosures to meet the disk rules and requiremen
3. Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide P N 014003051 00 This document explains how to convert a Model FC4700 storage system to a Model IP4700 file server by replacing and initializing the storage processors SPs loading IP4700 software and completing a Factory Initialization procedure Topics are REGUIPOMEN TS esaii aeeai e aee Seeonee bectassstssuekien stort saute ste 2 Conversion Kit S sici2i 3iiea ick arse EEE EEA 4 Related Documentation ccccccsccessecsscessecesscessecessecsseeesscecseesseeesseceaeeees 4 Converting the Hard ware sosise iie inise tiukkaa 5 Loading IP4700 SoftWwafe sssisiiisiiisiiiisisrisiiirsiaissiiissasssisisaiisioiu vrine 7 e Factory Unitiala Zig sass ccscscassesseesevesessee cxsensn ens ssenesessensstsensnessenssensespesnersgecs 12 Only authorized EMC service providers should perform the procedure described in this document CAUTION This procedure DOES NOT support the transfer or migration of data from an FC4700 system to an IP4700 file server Requirements The IP4700 file server supports twisted pair CAT5 copper Ethernet and or optical Ethernet cables The Disk Processor Enclosure DPE must have Two power supplies part number 005047159 and Two standby power supplies SPSs Each Disk Array Enclosure DAE must have two Link Control Cards LCCs and two power supplies Interconnection of DAEs must confor
4. Ox6fa Factory Zero Started 0x00 4 03 16 01 15 48 16 0_3 Ox6fa Factory Zero Started 0x00 5 03 16 01 15 48 16 0_4 Ox6fa Factory Zero Started 0x00 6 03 16 01 15 48 16 0_5 Ox6fa Factory Zero Started 0x00 7 03 16 01 15 48 16 0_6 Ox6fa Factory Zero Started 0x00 8 03 16 01 15 48 16 0_7 Ox6fa Factory Zero Started 0x00 9 03 16 01 15 48 16 0_8 Ox6fa Factory Zero Started 0x00 10 03 16 01 15 48 16 0_9 Ox6fa Factory Zero Started 0x00 11 03 16 01 15 48 16 1_0 Ox6fa Factory Zero Started 0x00 12 03 16 01 15 48 16 1_1 Ox6fa Factory Zero Started 0x00 13 03 16 01 15 48 16 1_2 Ox6 fa Factory Zero Started 0x00 14 03 16 01 15 48 16 1_3 Ox6fa Factory Zero Started 0x00 15 03 16 01 15 48 16 1_4 Ox6fa Factory Zero Started 0x00 16 03 16 01 15 48 16 1_5 Ox6 fa Factory Zero Started 0x00 17 03 16 01 15 48 16 1_6 Ox6fa Factory Zero Started 0x00 18 03 16 01 15 48 16 1_7 Ox6 fa Factory Zero Started 0x00 19 03 16 01 15 48 16 1_8 Ox6fa Factory Zero Started 0x00 ore any key to continue or q to Quit 4 E 16 At the fcli gt prompt type clearlog and then press lt Enter gt eS gt clearlog J gt 17 Once ALL the disk LEDs have stopped flashing type getlog at the fcli gt prompt and then press lt Enter gt Verify that all disks report successful completion of the zero disk operation NOTE If disk drives in a DAE do not report starting factory zero verify that both fibre loop cables are connected
5. PSB FAN N UNB UNB UNB UNB UNB UNB UNB UNB UNB UNB OK OK OK OK kk e ie kk kk ake e kk k k k k kk k k UNB UNB UNB UNB UNB UNB UNB UNB UNB UNB x kxk 03 16 2001 15 35 08 gmt x kx k k k k k k x x Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Zero Disk to Clear Drives Factory Initialization 11 On the second screen of SPSTAT information verify the following The system sees all the disk drives and they are unbound The system sees all power supplies and fan modules and they are OK NOTE If you do not see the DAEs and disks you expect verify that the Enclosure IDs and cabling are correct If you need to change them then you must reset both SPs You can reset the SPs by powercycling the system as described in step 3 on page 12 12 At the cli gt prompt type clearlog and then press lt Enter gt i gt clearlog J gt 13 At the fcli gt prompt type zd all and then press lt Enter gt fcli gt zd all J Status recv d opcode 0x8a status 0x0 The disk LEDs flash randomly on each shelf The zero disk function you just implemented enables the fast bind feature and takes approximately 15 minutes Go to step 14 now while the command executes Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Factory Initialization 14 At the fcli gt prompt t ype spstat and then pres
6. abort a step press q Press Enter to continue _ System Installation 30 To install the new system follow the instructions in the P4700 Quick Start Guide the on line wizard instructions and the IP4700 Release Notes for your software revision They will help you ensure that your license keys and other options are installed correctly You may need to update the IP4700 software to the latest release To determine whether you need to update it and how to receive the latest software contact your authorized IP4700 service provider Copyright EMC Corporation 2001 All rights reserved Revision 00 May 2001 No part of this publication may be reproduced or distributed in any form or by any means or stored ina database or retrieval system without the prior written consent of EMC Corporation The information contained in this document is subject to change without notice EMC Corporation assumes no responsibility for any errors that may appear EMC Corporation makes no warranties expressed or implied by operation of law or otherwise relating to this document the products or the computer software programs described herein EMC CORPORATION DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE In no event shall EMC Corporation be liable for a incidental indirect special or consequential damages or b any damages whatsoever resulting from the loss of use data or profits arising out of this d
7. as required by the internal code Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide 19 Factory Initialization N AAA ON BF WN FP OO PRPRPRPRPRPRPERP BEB OID RWNHNHE OW 19 Event 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 03 16 01 li gt getlog 4 Date a Ss 15 15 15 15 15 3 15 15 A533 15 T5 15 16 16 TG 16 16 16 16 16 a any key 48 SIE 57 573 Beles 51g 573 5s ST 573 Bilis 58 02 4 02 02 4 02 02 02 4 03 03 to CRU Event 16 1_9 Ox6fa 18 0_9 O0x6fc 18 1_2 Ox6fc 19 1_1 Ox6fc 57 1_0 Ox6fc 57 1_5 Ox6fc 57 1_3 Ox6fc 57 1_9 Ox6fc 57 1_4 Ox6fc 57 1_8 Ox6fc 57 1_7 Ox6fc 01 1_6 Ox6fc 40 0_5 Ox6fc 40 0_6 Ox6fc 40 0_3 Ox6fc 40 0_4 Ox6fc 41 0_7 Ox6fec 41 0_8 Ox6fc 34 0_1 Ox6fec 34 1 8 Ox6fec continue or Message Factory Factory Factory Factory Factory Factory Factory Factory Factory Factory Factory Factory Factory Factory Factory Factory Factory Factory Factory Factory No q Zero Zero Zero Zero Zero Zero Zero Zero Zero Zero Zero Zero Zero Zero Zero Zero Zero Zero Zero Zero to Quit Started Completed Completed Completed Completed Complete
8. be of equal or larger size than any other single drive in the configuration The DPE hot spare cannot be upgraded to a larger size 5 disks bound as 4 1 data parity drives 6 disks bound as 4 1 1 hot spare drive 10 disks bound as 2 sets of 4 1 drives 10 disks bound as 1 set of 8 1 hot spare drive Per the first disk rule you cannot mix 10K and 15K rpm or 18 Gbyte 36 Gbyte and 73 Gbyte drives in the same shelf Conversion Kit s Conversion Kit s The FC4700 to IP4700 with Quad LAN Conversion Kit FC IP4700F contains the following e P4700 Storage Processor qty 2 P N 005046657 e JP4700 Seed Disk P N 005047310 e P4700 Accessory Kit P N 005047044 e Conversion documentation P N 005047152 The FC4700 to IP4700 with Gbit LAN Conversion Kit FC IP4700G contains the following e P4700 Storage Processor qty 2 P N 005047012 e P4700 Seed Disk P N 005047310 e IP4700 Accessory Kit P N 005047044 e Conversion documentation P N 005047152 Related Documentation 1P4700 Quick Start Guide 069701170 IP4700 Installation Checklist CLAR PSP 002 Rev C IP4700 Administrator s Guide 069701169 IP4700 Installation and Service Guide 014003002 Fibre Channel Rails and Tray for Fibre Channel Enclosures Installation Guide 014002613 Non EMC Cabinet Mounting Hardware for Fibre Channel Enclosures and Switches Installation Guide 014003029 Mounting CLARION Arrays in Non EMC Supplied Racks CLAR PSB 013
9. cycle the DPE as described in Chapter 2 of the P4700 Installation and Service Guide a Turn the power switches on the Standby Power Supplies to the off position b Wait for all LED activity on the DPE to cease and for the fans to stop running Note that if the SPS was in the ready state it will hold power for 90 seconds c Wait an additional 30 seconds d Turn on the power switch on SPS A then do the same for SPS B 4 Enter V CTRL V immediately when the system displays the IP4700 banner 12 Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Factory Initialization eeeee eeaeee eee eeeeaea ee ee ee ee ee e ee ee e e e ee ee ee ee eQ e ee ee ee ee ee ee ee ee ee ee eeeee eeeeeee ee ee ee ee ee ee ee ee ee eeeee ee ee ee ee ee ee SP Components Please Wait J Once the IP4700 banner is displayed you have a maximum of 60 seconds to enter V Entering V should cause the following to display immediately If Enabling Factory Initialization Startup does not display one of the following may occur The system reboots and comes up to the IP4700 banner Starting SP Components Please Wait Raid System Started Successfully the display will recycle The system hangs In either case manually reset the SPs Reset SP A first then SP B You can reset the SPs by power cycling the system as described i
10. d Completed Completed Completed Completed Completed Completed Completed Completed Completed Completed Completed Completed Completed Completed a Extended Status 3 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 K 18 At the fcli gt prompt type clearlog and then press lt Enter gt a gt clearlog J D Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Factory Initialization Load DPE Chassis 19 At the fcli gt prompt type setser serial number and then press Serial Number lt Enter gt In the serial number field enter the last 12 characters beginning with F of the DPE Chassis Serial Number you recorded on page 12 fcli gt setser F20004701426 Warning Changing of the System Serial Number will cause an immediate reboot and a new Fibre Channel WWN to be created This command will fail if the write cache is not in the disable state and if any I O is outstanding Continue y nly W i 20 Enter y to reboot the system Although rebooting takes a few minutes be prepared to interrupt the autoboot process at the IP4700 banner 21 Enter V CTRL V immediately when the system displays the IP4700 banner eeeeae eeaeee eee eeeeeR ee ee b ee ee ee ee ee ee e e ee ee ee ee ee e Q Q e ee ee ee ee ee ee ee ee ee eeeee eee
11. e FS gt prompt type dsktodsk 2 0 and then press lt Enter gt This copies the image from disk 2 to disk 0 in approximately ten seconds 10 Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Loading IP4700 Software FS gt dasktodsk 2 0 Note If you see the error message disk 2 not on the loop ensure that the disk 2 LED is on solid and repeat Step 15 before trying again To finish the FC4700 to IP4700 conversion you must clear zero all the disks in the system of previous data and complete the IP4700 factory initialization process The next section in this guide describes the zero disk and factory initialization procedures Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Lon Factory Initialization Factory Initialization Factory initialization is a process that all new IP4700 systems experience prior to shipment The process begins by clearing all data from the DPE and DAE s in the IP4700 system and then binds the disks into file server volumes You must follow this same process to complete the FC4700 to IP4700 conversion and leave your system ready for the network initialization process common to all IP4700 file servers 1 Locate the DPE serial number label on the back of the unit Copy the number here You will need it later in the procedure 2 Verify that the yellow SPS LEDs are off and the green LEDs are either on or flashing 3 power
12. e is approximately 5 minutes When the system finishes booting it displays the IP4700 banner and a request to Press Enter to continue 24 Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Factory Initialization Starting SP Components Please Wait Raid System Started Successfully Volume Manager Started Successfully Root File System Started Successfully eeeeee eaeeee eee eeeeee ee ee ee ee ee ee e ee e ee ee ee e eQ e e ee ee ee ee ee ee ee e ee ee ee eeeeea e eeeeeea ee eQ ee ee ee ee ee ee e eeeeee ee ee ee ee ee o Enter to continue fh The conversion from an FC4700 to an IP4700 is now complete Perform the Site Next you must launch the IP4700 Initialization Wizard sometimes Initialization called the Setup Wizard The wizard guides you through the standard IP4700 network initialization Before you start make sure you have gathered the necessary network information and filled out the work sheets in Step 1 of the P4700 Quick Start Guide 29 To start the IP4700 Initialization Wizard via the serial port press lt Enter gt at the P4700 banner display The wizard displays a greeting message and asks you to continue Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide 25 Factory Initialization Setup guides you through the network initialization of your IP4700 If at any time you wish to
13. eeee ee ee ee ee ee ee ee ee e e e eeeee ee ee ee ee ee ee SP Components Please Wait J 22 When the Boot Console menu displays type 2 at the Enter Number of Your Choice field and then press lt Enter gt to reach the fcli command line Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide ar Factory Initialization a feli gt Q Enter Number Of Your Choice 2 J Nn OT FPF W N FP Access FCLI Recover Administrative State Recreate System Volumes Check File System on Volumes Authorized Service Personnel Only Quit FCLI Passthru Command Line Type menu to return to menu interface Boot Console Perform Factory Initialization Boot Console i 23 Atthe fcli gt prompt type setser and then press lt Enter gt fcli gt setser J Current serial number is 20004701426 24 Verify that you entered the serial number accurately If the serial number is incorrect repeat Steps 19 through 23 25 Atthe fcli gt prompt type clearlog and then press lt Enter gt 26 At the fcli gt prompt type menu and then press lt Enter gt The system exits fcli mode and displays the Boot Console menu Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Factory Initialization teli gt menu Boot Console Perform Factory Initialization Access FCLI Recreate System Volumes 1 2 3 Recover Administrati
14. h to the on position then do the same for SPS B Since the current 0 1 and 2 drives do not contain a loadable image the autoboot will fail The following screen displays the error as 3 16 2001 14 27 06 DiagName PROM Kernel N AutoBoot Enabled ByPass Auto Booting N Y 0 Starting loop initialization Loop is initialized No valid image exists Unable to load image ErrorTime 3 16 2001 14 27 16 ErrorCode 1012 ErrorDesc Autoboot fails loading flare image from fibre disks EndError Te J Wait for the system to display the FS gt prompt before continuing with Step 4 Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Loading IP4700 Software If necessary refer to chapter 3 in the P4700 Installation and Service Guide for instructions on removing and installing disk drives 4 Remove the disk drive installed in DPE slot 0 the leftmost slot and set it aside Note that the disks in DPE slots 0 2 should NOT be the 0 2 disks in the previous FC4700 configuration per step 8 in the preceding section Converting the Hardware 5 Install the seed disk P N 005047310 into DPE slot 0 Wait until the LED is on solid before continuing with the next step 6 AttheFS gt prompt type finit and then press lt Enter gt FS gt finit J Starting loop initialization Loop is initialized 7 Atthe FS gt prompt type showrev and then press lt Ente
15. he following e Exchange disk 0 with another drive e Make certain the new drive has never been in position 0 1 or 2 e Power cycle the DPE e Copy the system image from disk 2 to disk 0 e Begin again at Step 2 in this section 8 Atthe fcli gt prompt type spstat and then press lt Enter gt as shown on page 16 Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide 15 Factory Initialization SP A LOOP ID E FCLI Passthru Command fcli gt spstat J 0x7e Microcode Revision Statistics Logging DISABLED PEER SP PRESENT Disk Write Caching DISABLED R3 Write Buffering DISABLED WRITE CACHE DISABLED READ CACHE DISABLED RAID OPTIMIZED Mixed LUNs SP TYPE IP4700 LUN REMAPPING DISABLED A DP OOTOTAL 0000 DIRTY 0000 B TOTAL 0000 U DP OOTOTAL 0000 Requests Complete 19 SPS A NR SPS B NR Press any key to continue Line Type menu to return to menu interface 126 IP4700 R1 1 p8 4 A P 9 Examine the SPSTAT information carefully Verify the following the PEER SP is PRESENT the SPS units are in one of the following states TE NR or OK 10 Press lt Enter gt to go to the next screen a U slot DPE1 state nit Group DAE1 state nit Group felis 0 1 2 3 4 5 6 7 8 9 PSA
16. lay the FS gt prompt before continuing with Step d d Remove the disk drive installed in DPE slot 0 and set it aside e Install the seed disk P N 005047310 into DPE slot 0 10 Atthe FS gt prompt type finit and then press lt Enter gt FS gt finit J Starting loop initialization Loop is initialized CAUTION Failure to copy the image in the correct sequence will result in an unrecoverable condition L The conversion hard disk that contains your IP4700 software is not write protected Take care to enter the dsktodsk commands correctly and avoid overwriting the seed disk Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide EA Loading IP4700 Software 11 Atthe FS gt prompt type dsktodsk 0 1 and then press lt Enter gt This copies the image from the seed disk 0 to disk 1 in approximately ten seconds FS gt dsktodsk 0 1 J 12 Atthe FS gt prompt type dsktodsk 0 2 and then press lt Enter gt This copies the image from the seed disk 0 to disk 2 in approximately ten seconds FS gt dsktodsk 0 2 J 13 Remove the seed disk from DPE slot 0 and replace it with the drive you removed in step 4 14 Wait for the disk LEDs to stop flashing and remain on solid indicating that the disk is up and ready 15 Atthe FS gt prompt type finit and then press lt Enter gt FS gt finit J Starting loop initialization Loop is initialized 16 Atth
17. m to IP4700 rules LAN infrastructure must conform to IP4700 requirements for 10 100 Gbit 1000FD The system must include a management station to support CLARalert IP The conversion process requires a service laptop computer with Windows NT 4 0 with SP 6A HyperTerminal IE 5 0 and a null modem cable Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide IP4700 Disk Rules The following rules define IP4700 disk drive configurations Table 1 Supported Disks in DPE and DAEs Vendor Disk P N Description Seagate 005045272 18 Gbyte 10K rpm 005045932 18 Gbyte 10K rpm 005046730 18 Gbyte 10K rpm 005046734 18 Gbyte 15K rpm 005045936 36 Gbyte 10K rpm 005046732 36 Gbyte 10K rpm 005046734 73 Gbyte 10K rpm e You cannot mix disk sizes or spindle speeds within IP4700 system shelves That is each shelf in an IP4700 or attached DAE must consist of identical size disks All disks within a shelf must also run at the same spindle speed e The DPE must contain 10 disks of the same size and speed The IP4700 DPE is bound as a RAID 5 array with eight data drives one parity drive and one hot spare e The array MUST have a Hot Spare for the largest RAID 5 protected drive in the array e Each DAE in an IP4700 system can contain Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide The hot spare in the DPE will stand in for any RAID group The hot spare must
18. n step 3 on page 12 5 Enter V at the IP4700 banner Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide EA Factory Initialization T eeeeee eeeee eee a eeeee ae ee N ee ee ee ee ee ee e e ee ce ee ee e e e ee ee ee ee ee ee ee ee ee ceee aeeeeee ee ee e ee ee ee ee ee ee e e a eee eee ee ee ee ee ee Starting SP Components Please Wait ls Raid System Started Successfully E 6 When you see the Boot Console menu type 2 at the Enter Number of Your Choice field and then press lt Enter gt to reach the fcli command line T Boot Console N Perform Factory Initialization Access FCLI Recreate System Volumes 1 2 3 Recover Administrative State 4 5 Check File System on Volumes 6 Authorized Service Personnel Only Q Quit Boot Console Enter Number Of Your Choice 2 J FCLI Passthru Command Line Type menu to return to menu interface s gt wy 4 Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Factory Initialization Verify System Status 7 Atthe fcli gt prompt type ls and then press lt Enter gt feli Sis ls There are no currently bound units 03 29 2001 10 30 14 GMT fcli gt Note If the display indicates bound LUNs you have stale data on disk 0 Refer to the previous section Loading IP4700 Software for instructions as you perform t
19. ocument even if advised of the possibility of such damages Trademark Information EMC EMC CLARalert and Navisphere are registered trademarks of EMC Corporation All other trademarks mentioned herein are the property of their respective owners 26 Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide
20. r gt Minimum revisions of PROM and BIOS are displayed below FS gt showrev J Prom Version 03 05 97 Bios Version 4 06 v01 22 If the PROM and BIOS versions are at or above the minimum listed above proceed to step 8 If the PROM and or BIOS versions are below the minimum listed above perform the following FS gt engrmode on J FS gt dsktofl 0 to flash firmware from disk 0 to the SP FS gt dsktofl b 0 to flash BIOS from disk 0 to the SP FS gt engrmode off 8 Move the serial cable to SP B 8 Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Loading IP4700 Software 9 Repeat step 7 for the second SP upgrading PROM or BIOS if necessary If you did not upgrade PROM or BIOS in the preceding steps continue with step 10 If you did upgrade PROM or BIOS on either storage processor you need to power cycle the system to complete the firmware upgrade a Remove the seed disk and replace it with the disk drive you removed previously in Step 4 b Move the serial cable to SP A c power cycle the DPE as described in Chapter 2 of the P4700 Installation and Service Guide e Turn the power switches on the Standby Power Supplies to the off position e Wait for all LED activity on the DPE to cease and for the fans to stop running e Turn the power switch on SPS A to the on position then do the same for SPS B The autoboot will fail again Wait for the system to disp
21. s lt Enter gt Verify that a ZER has replaced the UNB frein gt spstat z b WRITE CACHE RAID OPTIMIZ T A DP OOTOTAL B TOTAL 0000 U DP OOTOTAL SPS A OK SPS B OK Press any key slot DPE1 state Unit Group DAE1 state Unit Group Ne SP A LOOP ID Ox7e 126 Microcode Revision IP4700 R1 1 p8 4 Statistics Logging DISABLED Disk Write Caching DISABLED a PEER SP PRESENT R3 Write Buffering DISABLED wy DISABLED READ CACHE DISABLED D Mixed LUNs SP TYPE IP4700 DISABLED LUN REMAPPING Requests Complete 19 0000 DIRTY 0000 0000 to continue 4d 0 1 2 3 4 5 6 7 8 9 PSA PSB FAN ZER ZER ZER ZER ZER ZER ZER ZER ZER ZER OK OK OK OK k k k k k k x kxk x k k x ZER ZER ZER ZER ZER ZER ZER ZER ZER ZER ko k k x kxk x x kxk x Pi 15 At the fcli gt prompt type getlog and then press lt Enter gt Verify that the log reports a Factory Zero Started for each disk drive Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide Factory Initialization Ecli gt getlog J b Event Date CRU Event Message Extended Status 1 03 16 01 15 48 16 0_0 Ox6fa Factory Zero Started 0x00 2 03 16 01 15 48 16 0_1 Ox6fa Factory Zero Started 0x00 3 03 16 01 15 48 16 0_2
22. ts listed on page 3 Exchange the FC4700 3 Remove the FC4700 storage processors following the procedures and IP4700 Storage in Chapter 3 of the P4700 Installation and Service Guide Processors a Install the IP4700 storage processors as described in the P4700 Installation and Service Guide 5 Pack the FC4700 storage processors in the IP4700 boxes 6 Return the two FC4700 storage processors to the appropriate crediting facility Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide os Converting the Hardware Move the FC4700 System Drives to Data Only Locations Verify Cabling Figure 1 7 Ensure that the DPE is configured with 10 disks of the same size and speed Supported disks and configurations are listed on page 3 of this document 8 Move disks 0 1 and 2 in the DPE to positions in slots 3 9 For example exchange disk 0 with disk 9 disk 1 with disk 8 and disk 2 with disk 7 If necessary refer to chapter 3 in the P4700 Installation and Service Guide for instructions on removing and installing disk drives Permanent FC4700 information in system disks 0 2 will prevent IP4700 powerup if the disks remain in or are returned to DPE slots 0 1 or 2
23. ve State 4 5 Check File System on Volumes 6 Authorized Service Personnel Only Q Quit Boot Console amp Enter Number Of Your Choice ee Perform the Factory 27 Perform the Factory Initialization process Initialization a Atthe Enter Number of Your Choice prompt type 1 and then press lt Enter gt b When asked to confirm type y and then press lt Enter gt The initialization process should take 5 minutes or less to complete Boot Console b Perform Factory Initialization Access FCLI Recover Administrative State Recreate System Volumes Check File System on Volumes OO Ae W N e Authorized Service Personnel Only Q Quit Boot Console Enter Number Of Your Choice 1 J Are you sure you want to perform Factory Initialization al volumes and data will be deleted y n y_ ff Fibre Channel FC4700 Array to IP4700 File Server Conversion Guide 23 Factory Initialization 28 When the initialization completes press lt Enter gt to reboot the system g Removing Raid Groups N Creating System Volumes Command setfkey id 80000002 q c n num encl NOT found 03 16 2001 16 12 31 GMT fcli gt Waiting For System Volumes Bind Initializing System Volumes Extracting Web and Help Files Creating Volumes AO and BO FACTORY INITIALIZATION COMPLETED SUCCESSFULLY Y Hit return to reboot the system 4J y Reboot tim
Download Pdf Manuals
Related Search