Electrolux Z2950 Series Vacuum Cleaner User Manual
Contents
1. Handle Self cleaning duster some models only Turbo tool some models only Screws located in the accessory package Carry handle assembly HOW TO ASSEMBLE CAUTION Assemble the cleaner before using CAUTION Moving parts Make sure ON OFF switch is in the OFF position before plugging in Step 1 Slide the handle into the hole as pictured FIG 2 Step 2 Slide the carry handle into place as pictured secure with 2 screws provided FIG 3 Step 3 Pull the electrical cord up to the cord retainer on the back of the looped handle and firmly push down into retainer This will keep the cord out of the way the next time you vacuum Step 4 Wind the cord around the two cord hooks on the back of the vacuum Step 5 Secure plug to the cord to prevent unwinding Step 6 Place the hose on the back of the vacuum wrapping it up and over the hose hook as shown FIG 4 Step 7 Secure the bottom of the self cleaning duster some models to the bottom hose fasten into place by tightening the screw Firmly push the end of the stretch hose into the top of the self cleaning duster Step 8 Store the wands on the side of the vacuum in front of the hose FIG 5 Step 9 Store the dusting brush on its holder FIG 6 m A S VA J M TA Y ccc Cc a W K S w N E JA Ex TRIN Tl 26 o o HOW TO USE WARN2. replacements can be obtained from your Electrolux Retailers and must be of the same colour as indicated by the coloured insert on the base of the plug lf difficulty is experienced in obtaining a replacement contact Electrolux Customer Services on 08706 055055 In no circumstances must the plug be used without a correct fuse cover fitted lf the plug that is fitted to your appliance is not suitable for your socket outlet it must be cut off and the appropriate plug fitted Remove the fuse from the cut off plug The cut off plug should then be disposed of to prevent the hazard of shocks in case it should be plugged into a 13 amp socket in another part of your home The wires in the mains cable of this appliance are coloured in accordance with the following code Blue Neutral Brown Live As the colours of the wires in the mains cable of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red lf using a three pin plug do not make any connection to the terminal marked with the letter E or by the earth symbol or coloured green or green and yellow This cleaner is double insulated and no earth connection is necessary It is in your interest to ensure
3. 4 Electrolux LOOPIE 2 4 IMPORTANT INFORMATION Upright Vacuum Cleaner Owner s Guide 4 GUARANTEE ousehold Type 22950 Series 5 QUICK REFERENCE 5 HOW TO ASSEMBLE 6 HOW TO USE 7 ROUTINE MAINTENANCE WS A eu 7 Dust Cup L v a 7 Top Filter s x 2 CA 8 Bottom Filter CU 8 PERIODIC MAINTENANCE 8 Brushroll IMPORTANT 8 9 Brushroll Belt For any advice on your cleaner and 10 PROBLEM SOLVING to order filters and accessories 10 Clear Hose please telephone the Electrolux Helpline on 11 Problems and Causes 08706 055055 2 The Electrolux Group FILTER REPLACEMENT CODE EF87a and EF82 www electrolux co uk IMPORTANT SAFEGUARDS When using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire electric shock or injury e Do not use outdoors or on wet surfaces o Do not leave vacuum cleaner when plugged in Turn off the switch and unplug the electrical cord when not in use and before servicing e Do not allow to be used as a toy Close attention is necessary when used by or near children e Use only as described in this manual Use only manufacturer s recommended attachments e Do not use with damaged cord or plug If vacuum cleaner is not working as it should has been dropped damaged left outdoors or dro
4. Carton D 1 Dusting Upholstery Brush 1 extra belt Dust Cup Filter DCF16 Riser Visor Turbo on some models Qaa S ies sS 1 extension tube 1 accessory package 1 vacuum cleaner handle 1 crevice wand 2 screws Thank you for purchasing an Electrolux cleaner Don t Forget to Use Genuine Electrolux Belts and Filters Caution Damages caused by the use of non genuine parts are not covered by the Electrolux Guarantee Part No 77828 06 06 Printed in PRC
5. ING Avoid injury Keep loose clothing hair fingers and all other parts of body away from any moving part such as the revolving brush Turn off the switch and unplug the cleaner before changing the cleaner height setting ON OFF Switch International symbol I means On International symbol O means Off FIG 7 Handle Release FIG 8 Step on handle release to pull handle back to a comfortable operating position To lower handle completely to the floor FIG 9 depress handle release a second time Helpful Information SS S S W gt CK OY mi M a d 3 amp K Before cleaning under low furniture check area first for objects that z2 ji might harm the unit or block the vacuum hose lL p Cleaner Height Setting An adjustment that raises or lowers the cleaner base to match the type of floor surface With the cleaner cord unplugged set the adjustment to lowest setting for maximum carpet cleaning If the cleaner is difficult to push move adjustment to next highest setting until cleaner is comfortable to push The brushroll must reach the carpet for effective cleaning For ease in moving the adjustment knob place handle in operating position and tilt cleaner back to remove weight from front wheels FIG 8 Helpful Information l ELL o co i IED a Ill H Listen to your cleaner If you notice a change in the sound of the motor or a chang
6. acement we recommend that this be carried out by Electrolux Service Staff Spares New filters brushrollers and drive belts can be obtained from Authorised Electrolux Dealers and electrical retailers If difficulty is experienced in obtaining spares please call us on 08706 055055 or visit our website at www shop electrolux co uk GUARANTEE This guarantee is in addition to your statutory and other legal rights This product is for household use only Electrolux products are carefully designed manufactured tested and inspected and in consequence we undertake to replace or repair any part found to be defective in materials or workmanship within one year of delivery to the original purchaser free of charge You may be required to take the product to your nearest service provider if the product requires attention during the first year There are certain conditions which may invalidate this guarantee a lt is dependent upon the appliance being correctly installed and used in accordance with the Company s instructions under normal domestic conditions within the United Kingdom or the Republic of Ireland b Service at all times must be carried out by an Electrolux Service Representative or authorised agent c The guarantee may be invalidated by unauthorised repair or modification of the appliance d You may be charged by Electrolux if you call for an engineer to resolve a problem that we believe is covered in the instruction booklet exa
7. ce foam filter into filter frame Step 5 Replace filter frame into top filter cover Replace top filter cover by pivoting back onto cleaner from left to right WARNING Always check that foam filter and frame are correctly installed in the cover before using vacuum CONTINUED 7 ROUTINE MAINTENANCE continued Filter Screen The filter screen is located directly above the dust cup and is easily removed by turning it counter clockwise It should be checked regularly to ensure an open airway Reinsert the screen by turning it clockwise FIG 17 Bottom Filter Maintenance Ref EF82 Check the bottom filter frequently For optimum performance replace bottom filter every 12 months Step 1 Remove the bottom filter cover by grasping the right edge and pivoting to the left FIG 18 Step 2 Pull filter frame from unit by pulling on tab in center FIG 19 Step 3 On some models remove filter pad and shake to remove excess dust If necessary this pad can be cleaned by vacuuming with another cleaner FIG 20 Step 4 Replace filter into unit Replace bottom filter cover by pivoting back onto cleaner from left to right PERIODIC MAINTENANCE CAUTION Turn off the switch and unplug the electrical cord before periodic maintenance Never operate the vacuum cleaner without the dust bag or filter assembly in place Brushroll The brushroll turns as it sweeps and combs the carpet nap Remove hair and threads from the brushro
8. e dust cup to become so full that it impedes the air flow thus reducing the cleaning efficiency of the machine The character of household dust and its effect on the air flow through the machine may vary considerably Fluffy dust allows air to pass through readily whereas fine powdery dust or proprietary cleaning powders pack tightly in the dust cup offering greater resistance to air flow and will reduce cleaning efficiency if the cup becomes overloaded e Always store your cleaner and spare dust filters in a dry place e Renew the filter pads three or four times a year This is essential to ensure continued high filtration of dust particles e Sucking up such items as stockings clippings of cloth sizeable pieces of paper wrappings from cigarette packets or sweets etc may block the hose Electrolux regrets that the clearing of blocked hoses cannot be regarded as service that can be given free of charge under the guarantee Should a blockage occur first disconnect the cleaner from the electricity supply refer to section headed Blockages If these operations are not successful contact Electrolux on 08706 055055 e Never pick up hot cinders or lighted cigarette ends e Make certain that your cleaner does not come into contact with water or any other liquid It is not designed as a wet pick up cleaner and must never be used on damp carpets or wet floors Important in the event of the mains supply cable of this vacuum cleaner requiring repl
9. e in performance it could simply indicate a common usage or maintenance issue Such as a need to raise or lower the carpet height adjustment possible blockage in hose or brushroll area or a broken or loose brushroll belt These are all easy to fix and the instructions are included in this owner s guide Becoming familiar with the information in this guide will help you to get the best possible performance from your new cleaner for many years to come eS UV S A LN 2 il Note While using accessories do not place cleaner on furniture or steps as the brushroll may cause damage Place cleaner on floor with the handle in storage position Step 1 To use accessories place desired accessory into the end of the hose or wand FIG 10 Dusting Upholstery Brush is for furniture blinds books lamp shades shelves curtains draperies cushions and fabrics Crevice Wand cleans corners stairs baseboards and between cushions Nested Extension Wands to add reach Step 1 Grasp both wands near ridges Step 2 Pull apart Step 3 Turn ridge end to center Step 4 Push wands together FIG 9 et The instructions in the booklet serve as a guide to routine maintenance To avoid unnecessary service calls check the top and bottom filters belt and brushroll often FIG 10 FIG 15 FIG 16 ROUTINE MAINTENANCE Note Turn off the switch and unplug the electrical cord before
10. in a cool dry area e Keep your work area well lighted e Unplug electrical appliances before vacuuming them PLEASE SAVE THESE INSTRUCTIONS The brush in the cleaning head rotates at high speed and can cause damage to the mains supply cable if the cleaner passes over it during cleaning operations Care should be taken to ensure that this does not happen If the cleaning head has accidentally passed over the mains supply cable the following action should be taken 1 Switch off and remove the plug from the socket outlet 2 Examine the mains supply cable for damage only after removing the plug from the socket outlet 3 lf there is any sign of damage to the supply cable it MUST be renewed The repair MUST be carried out by an Electrolux Service Agent or a similar qualified person 4 NEVER use the machine with a damaged mains supply cable Proprietary carpet conditioning and air freshening materials After using proprietary carpet conditioning powders it is recommended that the filters be changed Some of these preparations contain substances which if left in the vacuum cleaner for extended periods could damage the plastic mouldings which form the structure of the cleaner Many air fresheners household deodorants sprays and polishes contain a highly flammable gas propellant Because of this it is particularly important that these products are used strictly in accordance with the relevant manufacturer s instructions It is essential
11. ll so it continues brushing the carpet To maintain the most efficient cleaning the bristles must touch the carpet To test the bristle length hold a ruler against the underneath side of the cleaner If the bristles no longer touch the ruler replace the brushroll Brushroll Belt Ref ZE090 The brushroll belt turns the brushroll to agitate sweep and comb the carpet nap Check the belt regularly to be sure it is in good condition Replace the belt if it stretches cracks or loses tension Cut away any hair or threads wound around the brush roll or the belt pulley because the buildup could cause the belt to rotate unevenly VAN RN A N A wy FIG 20 Edge Kleen model shown some models only Edge Kleen model shown some models only Edge Kleen model shown some models only PERIODIC MAINTENANCE continued How To Replace Brushroll Belt Step 1 Lower handle to floor to change belt FIG 21 Step 2 Remove the two screws from the top of the hood FIG 22 Step 3 Lift hood to remove FIG 23 Step 4 Lift right end of brushroll FIG 24 Step 5 Remove and discard belt Step 6 Place new belt around motor shaft Step 7 Place new belt around brushroll pulley Step 8 Align left end cap with base Push end cap securely into place Make sure the square on the brushroll cap is in place FIG 25 Step 9 Pull right side of brushroll to stretch belt Secure right end cap i
12. mple blocked dirty filters Electrolux does not accept liability for all defects arising from neglect misuse or accident This guarantee excludes such normal wearing parts as drive belts brushes and filters as the life of these depends upon the amount and nature of use Proof of purchase will be required before service under guarantee is provided Please call 08706 055 055 for assistance IMPORTANT For future reference we suggest you record the following details here and keep the receipt with the handbook as proof of purchase Purchased from Date purchased Model no A Electrolux 101 Oakley Road LUTON BEDFORDSHIRE LU4 9QQ Features of the Electrolux vacuum cleaner and accessories supplied with it are protected in Great Britain and abroad by Patents or Registered Designs This appliance conforms with the requirements of the amended E E C directive No 89 336 EEC relating to electromagnetic compatibility EMC CE Electrolux may introduce modifications to their product from time to time and consequently the details given in this booklet are subject to alteration without notice 4 some models only L l y S ne QI iS OY cs CCC yy M u AC 2 eS ppt CN SS I A a a a GU JRC PARTS LIST Fic 1 Wand and crevice wand pull apart Dusting brush Hose Vacuum cleaner body 3 Electrical cord
13. nto base IMPORTANT Step 10 Rotate brushroll by hand 2 full rotations to properly position belt Step 11 Place hood back on cleaner Replace and tighten two screws Step 12 Return vacuum to upright position A n YE Lee UNIAN FIG 26 ee tt 10 PROBLEM SOLVING How to Clear Blockages in Hose CAUTION Turn off the switch and unplug the electrical cord before periodic maintenance Step 1 Firmly pull the end of the hose from the hose retainer on the hood of the vacuum FIG 26 Step 2 Check for blockages in the hose and hose retainer Flexing the hose may help loosen any blockage If no blockage is found continue to step 4 If blockage is found clear the blockage and replace the hose in the hose retainer If the blockage is in the hose retainer and cannot be cleared continue to step 3 Step 3 Remove the hood from the cleaner and check for a blockage in the brushroll area FIG 27 Make sure the hose inlet is clear If no blockage is found continue to step 4 After the blockage is found and cleared replace the hood on the cleaner Step 4 Twist the hose from the coupling elbow on the back of cleaner Check for blockages at cleaner opening and in hose FIG 28 If a blockage is found clear the blockage The screw attaching the clear hose adapter can be removed for better access to a blockage Step 5 Screw the hose back onto the back of the cleaner and replace the other end of the hose into the ho
14. pped into water return it to a service centre before using e Do not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners e Do not run vacuum cleaner over cord Keep cord away from heated surfaces e Do not use extension cords or outlets with inadequate current carrying capacity e Turn off all controls before unplugging e Do not unplug by pulling on cord To unplug grasp the plug not the cord e Do not handle plug or vacuum cleaner with wet hands e Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow e This vacuum cleaner creates suction and contains a revolving brushroll Keep hair loose clothing fingers and all parts of body away from openings and moving parts e Do not place cleaner on furniture or stairs as the brushroll may cause damage Place cleaner on floor with the handle in storage position while using attachments e Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes e Do not use without the dust cup or filter s in place e Belt pulleys can become hot during normal use To prevent burns avoid touching the belt pulley when servicing the drive belt e Use extra care when cleaning on stairs e Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present e Store your cleaner indoors
15. roll if bristles are worn Page 9 e Be sure hose adapter is secure Page 10 e Clean or replace filters Hint If picking up fine dust the filters may not look dirty but a fine substance tends to reduce suction when it blocks the air flow through the filter s Page 7 8 e Remove any clogs from hose that restricts the air flow Check base hose and long hose Page 10 e Empty dust cup Check to insure cup is properly seated and secured with lever engaged Hint Be sure both top amp bottom filters are in place Page 7 8 e Remove hood and clean debris or items from the brushroll area Page 9 e Replace a broken cut loose or out of shape belt Page 9 e Put handle in operating position Tilt the cleaner back to raise the front wheels off the floor Then turn the knob to a higher setting e Replace a broken cut loose or out of shape belt Page 9 e Hint Put handle in operating position Tilt the cleaner back to raise the front wheels off floor Then turn the knob Page 6 e Call Electrolux on 08706 055055 Have the model and serial numbers ready when you Call See rating plate beneath the cleaner e Call Electrolux on 08706 055055 Have the model and serial numbers ready when you Call See rating plate beneath the cleaner 11 If you experience any problems with your cleaner don t struggle taking it back to the shop Call our dedicated Customer Helpline for help and advice on 08706 055055 Accessory Items in This
16. routine maintenance Never operate the vacuum cleaner without the top and bottom filters in place Note When vacuuming carpet fresheners or cleaners powder plaster dust or similar fine substances the top and bottom filters will require more frequent maintenance Removing the Dust Cup Step 1 Remove dust cup by sliding dust cup lever from right to left FIG 11 Step 2 Grasp dust cup with both hands and pull out FIG 12 Step 3 Empty dust cup into trash Step 4 Reposition dust cup in cleaner body and secure by moving lever from left to right FIG 13 Top Filter Maintenance Ref EF87A This new Electrolux Upright uses a cyclone system as a primary filter and a secondary or top mounted filter that has been moved outside of the dirt cup This makes emptying the dirt cup much easier and less messy It is normal for this filter to trap fine particles pet hair and carpet fuzz It should be cleaned periodically depending on vacuuming conditions For optimum performance replace it every 12 months Step 1 Remove top filter cover by grasping right edge and pivoting to the left FIG 14 Step 2 Remove filter frame from top filter cover FIG 15 Step 3 Remove foam from filter frame FIG 16 Shake filter frame and foam filter to remove excess dust If necessary the filter frame and foam filter can be rinsed in lukewarm water and air dried Note The filter frame foam and cover are not dishwasher safe Step 4 When dry repla
17. se retainer on the hood of vacuum PROBLEM SOLVING CAUTION Turn off the switch and unplug the electrical cord before servicing Problem Cause Solution e Push plug securely into outlet e Try another outlet Motor will not start Electric Plug e Check circuit breaker Motor stops suddenly Thermal Cut Off e Refer to page 2 Does not clean the carpet or floor Filters Dust Cup Hose Belt Brushroll No suction at the end of hose Hose Adapter Filters Hose Dust Cup Noise from the brushroll area Brushroll Belt Cleaner is hard to push Cleaner Height Setting Belt Cleaner height knob will not turn Cleaner Height Setting Questions e Clean or replace filters Hint If picking up fine dust the filters may not look dirty but a fine substance tends to reduce suction when it blocks the air flow through the filter s Pages 7 8 e Empty dust cup Check to ensure cup is properly seated and secured with lever engaged Hint Be sure both top and bottom filters are in place e Be sure hose adapter is secure on back of cleaner Page 10 e Remove any blockages from the hose that restricts the air flow Page 10 e Check to see that the end of the hose is firmly pressed into the hose retainer in the hood of the vacuum Page 10 e Check base hose and long hose Page 10 e Replace a broken cut loose or out of shape belt Page 9 e Clean hair and thread from bristles and end cap area e Replace brush
18. that none of the above products are sprayed directly into the vacuum cleaner or any of its filters hose assembly dustbag chamber or dust cup Thermal Cut Off This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating If the cleaner switches off push the switch pedal once and unplug the cleaner Check the cleaner for a possible source of overheating such as a full dust cup a blocked hose or clogged filter If these conditions are found fix them and wait at least 60 minutes before attempting to use the cleaner After the 60 minute period plug the cleaner back in and push the on off switch On I If the cleaner still does not run please call Electrolux Customer Care BEFORE YOU START CHECK THE VOLTAGE Before connecting the cleaner to an electrical supply ensure that the voltage shown on the rating plate located beneath the cleaner is of the correct voltage for your electricity supply If it is not do not use the cleaner but refer back to your dealer CONNECTING TO YOUR ELECTRICITY SUPPLY Permanently connected to the cleaner is a mains supply 2 core cable fitted with a non rewirable plug incorporating a 13A fuse In the event of the fuse requiring replacement the fuse cover should be removed using a small screwdriver The old fuse MUST be replaced by a 13A ASTA approved BS1362 fuse or a BSI approved fuse The cover must be replaced before the plug is used again In the event of loss of the fuse cover
19. that the plug is correctly attached to the mains cable In case of doubt consult a qualified electrician as Electrolux cannot regard the repair of faults on the plug connection as a service that can be given free of charge under the terms of the guarantee 13 Amp Fuse Cord Clamp The yma on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product SERVICE Should you require service on your Electrolux cleaner please telephone Electrolux Customer Services on 08706 055055 Before requesting service please check whether your problem is covered under Service Checklist see below New filter pads brushrolls and drive belts can be obtained from Electrolux Retailers If difficulty is experienced in obtaining spares please contact Electrolux on 08706 055055 SERVICE CHECKLIST o f your cleaner will not operate check the plug connection plug fuse and mains fuse o Never allow th
Download Pdf Manuals
Related Search