Electrolux 84980 VI Dishwasher User Manual
Contents
1. Press function button 2 the indicator lights of function buttons 1 and 3 turn off while the indicator light of function button 2 goes on flashing the digital display indicates the current setting Od Rinse aid dispenser deactivated ic Rinse aid dispenser activated To change the setting press again function button 2 the digital display indicates the new setting To memorise the operation switch off the dishwasher by pressing the On Off button or wait about 60 seconds after which the dishwasher will automatically return to setting mode Operating instructions Audible signals Audible signals have been introduced to help indicate which operations the dishwasher is performing setting of the water softener end of programme intervention of an alarm due to malfunction Deactivation activation of the audible signals The dishwasher must be switched off Factory setting audible signals activated 1 Press the On Off button The indicator lights of the programme selection buttons will illuminate setting mode If only one programme selection button indicator light is illuminated this means that a washing programme is set The programme must be cancelled press simultaneously function buttons 2 and 3 for about 2 seconds the indicator light of the set programme button starts flashing After about 2 seconds the indicator lights of all the programme selection buttons will illuminate this mea2. Detergent tablets Detergent tablets of different brands dissolve at different speeds For this reason some detergent tablets cannot dissolve and develop their full cleaning power during short programmes Therefore please use long programmes when using detergent tablets to ensure the complete removal of detergent residuals Do not place the tablets in the tub or in the cutlery basket as this will result in poorer wash results The tablets should be placed in the detergent dispenser Concentrated detergent Based on their chemical composition dishwasher detergents can be split into two basic types conventional alkaline detergents with caustic components low alkaline concentrated detergents with natural enzymes The use of 50 C washing programmes in conjunction with concentrated detergents reduces pollution and is good for your dishes these wash programmes are specially matched to the dirt dissolving properties of the enzymes in the concentrated detergent For this reason 50 C wash programmes in which concentrated detergents are used can achieve the same results that can otherwise only be achieved using 65 C programmes Combi detergents If you are using dishwasher detergent that includes the rinse aid function this must be placed in the detergent compartment In this case the rinse aid dispenser must be empty in order to avoid a double dosage If in the rinse aid dispenser there is still rinse aid you must wait until
3. The appliance should not be connected to the electrical supply by means of an extension cable In case that the electrical cable has to be replaced please contact your local Service Force Centre Warning A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that it is disposed of safely Hints for test centres Hints for test centres Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme see Washing programmes chart Test in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme see Washing programmes chart Load 12 standard place settings Rinse aid setting Position 4 type III Detergent dosage 30 g type B Arrangement lower basket without salad bowl Arrangement lower basket with salad bowl Arrangement cutlery basket 47 A From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx 14 billion USD in more than 150 countries around the world AEG Hausger te GmbH Postfach 1036 D 90327 Nurnber
4. e Rinse aid was not used e The rinse aid dispenser is empty There are streaks milky spots or a bluish coating on glasses and dishes e Decrease rinse aid dosing Water drops have dried onto glasses and dishes e Increase rinse aid dosing e The detergent may be the cause Contact the detergent manufacturer s consumer care line 35 Service 36 If after all these checks the problem persists contact your local Service Force Centre quoting the model Mod product number PNC and serial number S N This information can be found on the rating plate located on the side of the dishwasher door see picture So that you always have these numbers at hand we recommend you to make a note of them here RA07 This product should be serviced by an authorised service engineer and only genuine spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Service Force Centre Always insist on genuine spare parts Service Service and Spare Parts sanwessronce In the event of your appliance requiring service or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning 08705 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code
5. BRO Operating instructions i Adjusting the dose According to the finish and drying results obtained adjust the dose of rinse aid by means of the 6 position selector position 1 minimum dosage position 6 maximum dosage The dose is factory set in position 4 5 Increase the dose if there are drops of water or lime spots on the dishes after A washing AN Reduce it if there are sticky whitish iy S2 streaks on the dishes or a bluish film on X glassware or knife blades BR09 Top up the rinse aid when the indicator light on the control panel illuminates 17 Operating instructions 18 In daily use A e Check if it s necessary to refill with dishwasher salt or rinse aid e Load cutlery and dishes into the dishwasher e Fill with dishwasher detergent e Select a wash programme suitable for the cutlery and dishes e Start the wash programme Loading cutlery and dishes Sponges household cloths and any object that can absorb water may not be washed in the dishwasher e Before loading the dishes you should Remove large left overs Soften remnants of burnt food in pans e When loading the dishes and cutlery please note Dishes and cutlery must not impede the rotation of the spray arms Load hollow items such as cups glasses pans etc with the opening downwards so that water cannot collect in the container or a deep base Dishes and items o
6. and helps prevent the build up of limescale Cleaning the filters The filters must be checked and cleaned from time to time Dirty filters will degrade the washing result 1 Open the door remove the lower basket 2 The dishwasher filter system comprises a coarse filter A a microfilter B and a flat filter C Unlock the filter system using the handle on the microfilter and remove MA36 Operating instructions 4 Take hold of the coarse filter A by the handle with the hole and remove from the microfilter B 5 Clean all filters thoroughly under running water 6 Remove the flat filter C from the base of the washing compartment and clean both faces thoroughly MA48 N Put the flat filter C back in the base of the washing compartment Place the coarse filter A in the microfilter B and press together Put the filter combination in place and lock by turning the handle clockwise to the stop During this process ensure that the flat filter does not protrude above the base of the washing compartment oO Attention Under no circumstances may the dishwasher be used without filters Incorrect repositioning and fitting of the filters will produce poor washing results NEVER try to remove the upper spray arm If residues of soil have clogged the holes in the upper spray arm remove them with a cocktail stick 31 Operating
7. area For the address of your local Service Force Centre and further information about Service Force please visit the website at www serviceforce co uk Before calling out an engineer please ensure you read the details under the heading Something not working When you contact the Service Force Centre you will need to give the following details 1 Your name address and post code 2 Your telephone number 3 Clear and concise details of the fault 4 The model and serial number of the appliance found on the rating plate 5 The purchase date Please note that a valid purchase receipt or guarantee documentation is required for in guarantee service calls Customer Care Department For general enquiries concerning your AEG Electrolux appliance or for further information on AEG Electrolux products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www AEG co uk Customer Care Department Electrolux 55 77 High Street Slough Berkshire SL1 1DZ Tel 08705 950950 x Calls to this number may be recorded for training purposes 37 Guarantee Conditions 38 Guarantee Conditions Standard Guarantee Conditions We AEG Electrolux undertake that if within 12 months of the date of purchase this AEG Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option
8. by the salt indicator light on the control panel which comes on when the salt has finished The salt indicator light on the control panel can remain illuminated for 2 6 hours after the salt has been replenished assuming the dishwasher remains switched on If you are using salts that take longer to dissolve then this can take longer The function of the machine is not affected Do not worry if water over flows from the unit when filling with salt this is quite normal 15 Operating instructions 16 Rinse aid Rinse aid is automatically added during the last rinse ensuring thorough rinsing and spot and streak free drying The dispenser which is positioned inside the door holds about 110 ml of rinse aid which is sufficient for 16 40 dishwashing programmes depending upon the dosage setting Filling with rinse aid 1 Open the container by pressing the release button A 2 Add the rinse aid until the container is completely full The maximum level for filling is indicated by max SI Nk a CE Ne ales O ZN Ensure that the lid is closed after every refill Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash Only use branded rinse aid for dishwashers Never fill the rinse aid dispenser with any other substances e g dishwasher cleaning agent liquid detergent This would damage the appliance
9. dial Salt container Detergent dispenser Rinse aid dispenser Control panel Rating plate O oO N OD UU RP WYN BP Filters 10 Lower spray arms 11 Upper spray arm NOTE this dishwasher has internal lights that turn on and off when the opening and closing of the dishwasher s door occurs In the case that these lights have to be replaced please contact your local Service Force Centre Operating instructions The control panel Function buttons Digital display Ea Siak 3 in 1 button 1 Programme selection Indicator lights On Off button buttons Delay start button Function buttons in addition to the selection of the washing programme and the delay start option the following functions can also be set with the help of these buttons the setting of the water softener activation deactivation of the rinse aid dispenser deactivation activation of the audible signals the cancelling of a washing programme in progress Programme selection buttons allows the selection of the desired washing programme see Washing programmes chart Delay start button this option allows the start of the programme to be delayed from 1 to 19 hours The digital display indicates the level of hardness to which the water softener is set if the rinse aid dispenser is activated deactivated if the audible signals are activated deactivated the approximate remaining time of the running pr
10. instructions 32 Prolonged periods of non operation If you are not using the machine for any period of time you are advised to 1 Unplug the appliance and then turn off the water 2 Leave the door ajar to prevent the formation of any unpleasant smells 3 Leave the inside of the machine clean Frost precautions Avoid placing the machine in a location where the temperature is below 0 C If this is unavoidable empty the machine close the appliance door disconnect the water inlet pipe and empty it Moving the machine If you have to move the machine moving house etc 1 Unplug it 2 Turn the water tap off 3 Remove the water inlet and discharge hoses 4 Pull the machine out together with the hoses Avoid over tilting the machine during transportation Operating instructions Something not working Certain problems are due to the lack of simple maintenance or oversights which can be solved with the help of the instructions given here without calling out an engineer Important If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a charge will be made even if the appliance is in guarantee a flashing fault code appears The dishwasher will not start or stops during operation and a sequence of intermittent audible signals are heard Open the dishwasher s door The intervention of an alarm is indicated by the continuous flashing o
11. is designed to take saucepans lids plates salad bowls cutlery etc Arrange serving dishes and large lids up to 33 cm in diameter on the left hand side of the basket ensuring that the spray arms can turn freely pan NZ lt i i UI104 The rows of prongs can be easily lowered to allow you to load pots pans and bowls D UI105 UI106 Operating instructions The cutlery basket Long bladed knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket Take care when loading or unloading sharp items such as knives Forks and spoons should be placed in the removable cutlery basket with the handles facing downwards and the knives with their handles facing upwards If the handles protrude from the bottom of the basket obstructing the lower spray arm load the cutlery with the handles facing upwards Mix spoons with other cutlery to prevent them from sticking together For best results we recommend you to as use the cutlery grids provided if the size and dimensions of the cutlery allow it The cutlery basket is in two parts which can be separated to give greater loading flexibility To separate the two parts slide them horizon
12. repair or replace the same FREE OF CHARGE for labour materials or Carriage on condition that e The appliance has been correctly installed and used only on the electricity supply stated on the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us e All service work under this guarantee must be undertaken by a Service Force Centre e Any appliance or defective part replaced shall become the Company s property e This guarantee is in addition to your statutory and other legal rights Home visits are made between 8 30am and 5 30pm M onday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover e Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic e Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom e Appliances found to be in use within a commercial environment plus those which are subject to rental agreements e Products of AEG Electrolux manufacture which are not marketed by AEG Electrolux Guarantee Conditions European Guarantee If you should move to another coun
13. see the chart Examples if the current level is 5 by pressing button 1 once level 6 is selected if the current level is 10 by pressing button 1 once level 1 is selected 5 To memorise the operation switch off the dishwasher by pressing the On Off button or wait about 60 seconds after which the dishwasher will automatically return to setting mode Operating instructions Filling with dishwasher salt Only use salt specifically designed for use in dishwashers All other types of salt not specifically designed for use in a dishwasher especially table salt will damage the water softener Only fill with salt just before starting one of the complete washing programmes This will prevent any grains of salt or salty water which may have been spilt remaining on the bottom of the machine for any period of time which may cause corrosion To fill 1 Open the door remove the lower basket and unscrew the cap of the salt container by turning it anticlockwise 2 Pour 1 litre of water inside the container this is necessary only before filling with salt for the first time 3 Using the funnel provided pour in the salt until the container is full 4 Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket 5 Replace on the cap tightly turning it clockwise until it stops with a click The salt container will require topping up periodically You are reminded of this
14. the appliance does not stand on the electrical supply cable The sides of the dishwasher must never be drilled to prevent damage to hydraulic components Child safety This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the product Operating instructions Packaging parts may be dangerous for children who could even be suffocated You should therefore keep all packaging well away from children The water in your dishwasher is not for drinking Detergent residues may still be present in your machine Keep children well away from your dishwasher when the door is open Keep all detergents in a safe place out of children s reach Your dishwasher in day to day use Items that are contaminated by petrol paint steel or iron debris corrosive acidic or alkaline chemicals must not be washed in this dishwasher Under no circumstances should you open the door whilst the appliance is in operation especially during the washing phase hot water may escape However if the door is opened a safety device ensures that the machine stops Only use products detergent salt and rinse aid specifically designed for use in dishwashers Long bladed knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket Ensure that the door of the dishwash
15. turn off In the digital display will appear flashing the running time in minutes of the programme that has been set Close the dishwasher s door the programme will start automatically Setting and starting the programme with the delay start Once the washing programme has been selected press the delay start button the corresponding indicator light will illuminate and 1h appears in the digital display Press the delay start button until the number of hours desired from 1 hour up to 19 hours appear in the digital display Close the dishwasher door the countdown starts automatically and will decrease with steps of 1 hour The opening of the door will not modify or interrupt the countdown Once the delay start has elapsed the washing programme will start automatically NOTE The start of the programme or the countdown of the delay start will occur only after the closure of the door until this moment it is possible to modify the set made 27 Operating instructions 28 AN A 5 To interrupt or cancel a washing programme in progress Interrupt or cancel a washing programme in progress ONLY if it s absolutely necessary Attention Hot steam may escape when the door is opened Open the door carefully Interrupt a washing programme in progress Open the dishwasher door the programme will stop Close the door the programme will start from the point at which it was interrupted Cancel a washing pro
16. FAVORIT 84980 VI Dishwasher Instruction book AEG TE PERFEKT IN FORM UND FUNKTION Electrolux A i QJ i Dear customer Please read this User Information carefully and keep it to refer to at a later date Pass it on to any subsequent owner of the appliance The following symbols are used in the text Safety instructions Warning Notes that concern your personal safety Attention Notes that show how to avoid damage to the appliance Useful tips and hints Environmental information Your dishwasher has the new washing system IMPULSE WASHING With this dishwashing system the motor speed and spray pressure are varied during the wash cycle to achieve better cleaning of the dishes It is for this reason that the noise level varies during the dishwashing cycle Contents Safety instructions Disposal Economical and ecological dishwashing Description of the appliance The control panel Prior to using for the first time The water softener Filling with dishwasher salt Rinse aid In daily use Loading cutlery and dishes The lower basket The cutlery basket The upper basket Use of detergent Different kinds of detergent Washing programmes Starting a washing programme Maintenance and cleaning Cleaning the filters Something not working Technical specifications Building in Levelling Fixing to the adjacent units Water supply connections Water inlet hose with safety valve Water outle
17. e of Finish detergents rinse aid and salt fn a DE15 25 Operating instructions Washing programmes Cycle Consumption description values Type of Degree of y Programme load soil a Slela toy Pelee T E AAEN aE IR 5 Pee ebedals de 105 1 65 20 Automatic Crockery cutlery Normal light soil ee e e bis bis bis pots and pans 1 2x 140 2 0 30 Crockery and 40 MIN cutlery Fresh soil Fofo fo o e a Godk tl 141 2 2 INTENSIVE rockery cutlery Heavy soil S E alo licila CARE 70 pots and pans 2x 151 25 ase a Normal soil aolo 15013 18 1 Ideal for washing crockery and cutlery of breakfast and dinner fresh soil This is the perfect daily programme made to meet the needs of a family of 4 persons who only wish to load breakfast and dinner crockery and cutlery 2 Testing programme for EN 50242 see Hints for Test Centres This programme developed for the use of detergents with enzymes allows you to achieve with reduced consumption of energy the same cleaning results that would otherwise be obtained only with the 65 C programmes and conventional detergents To compensate the lower temperature the duration of washing and drying have been extended 3 The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by the variations of the power supply AUTOM ATIC washing programme During the AUTOMATIC washing programme
18. electronic setting of the water softener is possible ONLY with the 3 in 1 function deactivated The dishwasher is factory set at level 5 Press the On Off button The indicator lights of the programme selection buttons will illuminate setting mode If only one programme selection button indicator light is illuminated this means that a washing programme is set The programme must be cancelled press simultaneously function buttons 2 and 3 for about 2 seconds the indicator light of the set programme button starts flashing After about 2 seconds the indicator lights of all the programme selection buttons will illuminate this means that the set washing programme has been cancelled and the machine is now in setting mode Press simultaneously function buttons 2 and 3 until the indicator lights of function buttons 1 2 and 3 start flashing 13 Operating instructions 3 Press function button 1 the indicator lights of function buttons 2 and 3 turn off while the indicator light of the button 1 goes on flashing the digital display indicates the current level and a sequence of intermittent audible signals are heard The current level is indicated by the number visible in the display and the number of intermittent audible signals heard Example SL displayed 5 audible signals level 5 4 To change the level press function button 1 Each time the button is pressed the level changes For the selection of the new level
19. er is always closed when it is not being loaded or unloaded In this way you will avoid anybody tripping over the open door and hurting themselves When finishing loading or unloading close the door as an open door can be a hazard Do not sit or stand on the open door Isolate the appliance from the power supply and turn off the water supply after use This product should be serviced by an authorised service engineer and only genuine spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Service Force Centre Always insist on genuine spare parts Operating instructions e Disposal Dispose of the dishwasher packaging material correctly All packaging materials can be recycled Plastic parts are marked with standard international abbreviations gt PE lt for polyethylene e g sheet wrapping material gt PS lt for polystyrene e g padding material always CFC free gt POM lt for polyoxymethylene e g plastic clips Cardboard packaging is manufactured from recycled paper and should be deposited in the waste paper collection for recycling As and when you cease to use your dishwasher and withdraw it from service your should render it unserviceable before having it disposed of AN Warning Children at play could lock themselves in your dishwasher or otherwise endanger
20. f cutlery must not lie inside one another or cover each other To avoid damage to glasses they must not touch Lay small objects in the cutlery basket e Plastic items and pans with teflon have a tendency to retain water drops these items will not dry as well as porcelain and steel items Operating instructions For washing in the dishwasher the following cutlery dishes are not suitable e Cutlery with wooden horn china or mother of pearl handles e Plastic items that are not heat resistant e Older cutlery with glued parts that is not temperature resistant e Bonded cutlery items or dishes Pewter or copper items Lead crystal glass e Steel items subject to rusting e Wooden platters e Items made from synthetic fibres are of limited suitability e Only wash stoneware in the dishwasher if it is specifically marked as being dishwasher safe by the manufacturer e Glazed patterns may fade if machine washed frequently e Silver and aluminium parts have a tendency to discolour during washing Residues e g egg white egg yolk and mustard often cause discolouring and staining on silver Therefore always clean left overs from silver immediately if it is not to be washed straight after use e Some types of glass can become dull after a large number of washes 19 Operating instructions 20 Open the door and slide out the baskets to load the dishes The lower basket The lower basket
21. f the indicator light of the running programme a fault code as described in the chart is visible in the digital display Carry out the following suggested corrective actions Fault code Malfunction appears in the digital display The machine does not fill with water ic appears in the digital display The dishwasher will not drain JD appears in the digital display Possible cause The water tap is blocked or furred with limescale The water tap is turned off The filter where present in the threaded hose fitting at the water inlet valve is blocked The water inlet hose has not been correctly laid or it is bent or squashed The sink spigot is blocked The water drain hose has not been correctly laid or it is bent or squashed Anti flood device is activated Solutions Clean the water tap Turn the water tap on Clean the filter in the threaded hose fitting Check the water inlet hose connection Clean out the sink spigot Check the water drain hose connection Close the water tap and contact your local Service Force Centre 33 Operating instructions 34 Once the checks have been carried out to continue the programme press one of the programme selection button and close the door The programme will continue from the point at which it was interrupted If the fault code reappears contact your local Service Force Centre For other combinations of fault c
22. g http www aeg hausgeraete de Copyright by AEG 152 955 36 0 Subject to change without notice 04 05
23. gramme in progress Open the dishwasher door Press simultaneously function buttons 2 and 3 for about 2 seconds the indicator light of the button corresponding to the running programme starts flashing After about 2 seconds the indicator lights of all the programme selection buttons will illuminate this means that the running programme has been cancelled and that the machine has returned to setting mode If anew washing programme will be selected check that there is detergent in the detergent dispenser To cancel a delay start in progress To cancel a delay start in progress you have to reset the dishwasher follow the same instructions given in Cancel a washing programme in progress Cancelling a delay start involves also the cancelling of the set washing programme In this case you have to set the washing programme again Operating instructions AN 7 End of the washing programme The dishwasher will automatically stop and an audible signal informs you of the end of the washing programme If the door is not immediately opened at the end of the programme air will circulate inside the dishwasher to prevent residual steam recondensing on the dishes as water droplets This device operates intermittently for about 20 minutes as long as the dishwasher is switched on If the On Off button is pressed or the door is opened during these 20 minutes the device will be automatically cancelled Open the dishwasher s door leave
24. hed Levelling Good levelling is essential for correct closure and sealing of the door When the appliance is correctly levelled the door will not catch on either side of the cabinet If the door does not close correctly loosen or tighten the adjustable feet until the machine is perfectly level Fixing to the adjacent units The dishwasher must be secured against tilting Therefore make sure that the counter it is fixed under is suitably secured to a fixed structure adjacent kitchen units cabinets wall 41 Installation instructions 42 Water supply connections This dishwasher must be plumbed into a cold water supply For making the connection itself the coupling nut fitted to the machine s supply hose is designed to screw onto a 3 4 inch gas thread spout The water pressure must be within the limits given in the Technical specifications Your local Water Authority will advise you on the average mains pressure in your area The water inlet hose must not be kinked crushed or entangled when it is being connected The inlet hose must hang down vertically from the supply tap The dishwasher features fill and drain hoses which can be turned either to the left or the right to suit the installation by means of the locknut The locknut must be correctly fitted to avoid water leaks Attention NOT all models of dishwashers have fill and drain hoses provided with locknut In this case this kind of facility i
25. it has finished before using these kind of detergents The rinse aid indicator light will always remain illuminated when the machine is switched on not all dishwasher models are foreseen with rinse aid indicator light Special salt for dishwasher must still be used Operating instructions Use of 3 in 1 combi detergents General advice These products are detergents with integrated and combined detergent rinse aid and salt functions 1 Before using these products you should first check that the water hardness in your supply is compatible with the use of these products as per the detergent manufacturers on the product packaging 2 These products should be strictly used according to the detergent manufacturers instructions 3 If you encounter problems when using 3 in 1 products for the first time then please contact the detergent manufacturers care line the telephone number is given on the product packaging Special advice When using combination 3 in 1 products select the 3 in 1 function il If you decide to turn back to the use of the standard detergent system we advise that you e Refill both the salt container and rinse aid dispenser e Switch the water hardness setting to the highest possible position and run from 1 to 3 normal washing programmes without a load e Readjust the water hardness setting again according to the hardness of the water in your area For best results we recommend the us
26. it ajar and wait a few minutes before removing the dishes in this way they will be cooler and the drying will be improved In the digital display appears 0 programme end only in this case the programme has ended Switch off the dishwasher by pressing the On Off button 8 Unloading the dishwasher Hot dishes are sensitive to knocks The dishes should therefore be allowed to cool down before removing from the appliance Empty the lower basket first and then the upper one this will avoid water dripping from the upper basket onto the dishes in the lower one Water may appear on the sides and the door of the dishwasher as the stainless steel will eventually become cooler then the dishes When the washing programme has finished it is recommended that the dishwasher is unplugged and the water tap turned off 29 Operating instructions 30 Maintenance and cleaning A Clean the external surfaces of the machine and control panel with a damp soft cloth If necessary use only neutral detergents Never use abrasive products scouring pads or solvent acetone trichloroethylene etc Ensure that the seals around the door the detergent and rinse aid dispensers are cleaned regularly with a damp cloth We recommend the use of Finish Dishwasher Cleaner every 3 months or run a 65 C wash programme without dishes using detergent Regular use of Finish Dishwasher Cleaner cleans inaccessible parts eliminates unpleasant food odours
27. nection is given on the Voltage rating plate on the inner edge of the dishwasher s door Overall power Fuse Water supply pressure Minimum 50 kPa 0 5 bar Maximum 800 kPa 8 bar Capacity 12 place settings 73 23 or 19 2 73 Low Voltage Directive and subsequent modifications 89 336 or 3 5 89 Electromagnetic Compatibility Directive and subsequent modifications C This appliance complies with the following E E C Directives Installation instructions AN Any electrical and or plumbing work required to install this appliance should be carried out by a qualified electrician and or plumber or competent person Remove all packaging before positioning the machine If possible position the machine next to a water tap and a drain Building in This dishwasher is designed to be fitted under a kitchen counter or worksurface Attention Carefully follow the instructions on the enclosed template for building in the dishwasher and fitting the furniture panel No further openings for the venting of the dishwasher are required but only to let the water fill and drain hose and power supply cable pass through The dishwasher incorporates adjustable feet to allow the adjustment of the height During all operations that involve accessibility to internal components the dishwasher has to be unplugged When inserting the machine ensure that the water inlet hose the drain hose and the supply cable are not kinked or squas
28. ns that the set washing programme has been cancelled and the machine is now in setting mode 2 Press simultaneously function buttons 2 and 3 the indicator lights of function buttons 1 2 and 3 start flashing 3 Press function button 3 the indicator lights of function buttons 1 and 2 turn off while the indicator light of the button 3 goes on flashing the digital display indicates the current setting Gb Audible signals deactivated b Audible signals activated factory set 4 To change the current setting press again function button 3 the digital display will indicate the new setting 5 To memorise the operation switch off the dishwasher by pressing the On Off button or wait about 60 seconds after which the dishwasher will automatically return to setting mode 11 Operating instructions 12 Prior to using for the first time Before using your dishwasher for the first time 1 Ensure that the electrical and water connections comply with the installation instructions 2 Remove all packaging from inside the appliance 3 Set the water softener 4 Pour 1 litre of water inside the salt container and then fill with dishwasher salt 5 Fill the rinse aid dispenser The water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply which would have a detrimental or adverse effect on the operation of the appliance The higher the c
29. odes not described in the above chart will appear please contact your local Service Force Centre there are problems when operating the dishwasher Fault The programme does not start There is a whistling noise during washing Possible cause The dishwasher door has not been properly closed The main plug is not plugged in The fuse has blown in the household fuse box For dishwasher models with delay start option Delay start has been selected The whistling is not a cause for concern Solutions Close the door Insert the mains plug Replace the fuse If dishes are o be washed immediately cancel the delay start Use a different brand of detergent Operating instructions the wash results are not satisfactory The dishes are not clean e The wrong washing programme has been selected e The dishes were arranged in such a way as to stop water reaching all parts of the surface The baskets must not be overloaded e The spray arms do not rotate freely due to wrong arrangement of the load e The filters in the base of the washing compartment are dirty or incorrectly positioned e Too little or no detergent has been used e Where there are limescale deposits on the dishes the salt container is empty or the wrong level of the water softener has been selected The drain hose connection is not correct e The salt container cap is not properly closed The dishes are wet and dull
30. ogramme the end of the programme a zero 0 will appear in the digital display the countdown of the delay start fault codes concerning malfunction of the dishwasher Operating instructions Indicator lights have the following meanings S Salt refilling indicator light illuminates when the salt has run out Rinse aid refilling indicator light illuminates when rinse aid has run out 3 IN 1 illuminates when the 3 in 1 function is activated 3 in 1 button This appliance is equipped with the 3 in 1 function that allows the use of the 3 in 1 combi detergent tablets This function can be selected with all washing programmes With the selection of this function the inflow of rinse aid and salt from each respective supply container is automatically deactivated and also the indicator lights for salt and rinse aid are deactivated Select the 3 in 1 function before the set of a washing programme Once selected this function button indicator light illuminated it will remain active also for the following washing programmes to deactivate the function press the button button indicator light off With the use of the 3 in 1 function the cycle durations may change In this case in the digital display the indication of the running time of the programme is automatically updated NOTE Once the programme is running the 3 in 1 function can NO longer be changed If you want to exclude the 3 in 1 func
31. ontent of these minerals and salts the harder your water is Water hardness is measured in equivalent scales German degrees French degrees and mmol l millimol per litre The softener should be adjusted according to the hardness of the water in your area Your local Water Authority can advise you on the hardness of the water in your area The water softener must be set in both ways manually using the water hardness dial and electronically using the function buttons on the control panel Water hardness Adjusting the water Level dH TH mmol l Range hardness setting indicated in ane german french degrees millimol a is the digital au e ternati unit for i a hanna of water Mentel oe cay display PES 51 70 91 125 9 0 12 5 10 ABH 10 43 50 76 90 7 6 8 9 9 gL 9 37 42 65 75 6 5 7 5 IV 8 8L 8 29 36 51 64 5 1 6 4 2 7 7L 7 23 28 40 50 4 0 5 0 6 6L 6 19 22 33 39 3 3 3 9 ill 5 SL 5 15 18 26 32 2 6 3 2 4 4L 4 11 14 19 25 1 9 2 5 lI 3 JL 3 4 10 7 18 0 7 1 8 Vil 1 2 eb 2 1 lt 4 lt 7 lt 0 7 l no salt FE 1 necessary Operating instructions a Setting manually 1 2 3 4 The dishwasher is factory set at position 2 Open the dishwasher door Remove the lower basket from the dishwasher Turn the water hardness dial to position 1 or 2 see table Replace the lower basket AA07 b Setting electronically 1 The dishwasher must be switched off NOTE the
32. s not possible If the machine is connected to new pipes or pipes which have not been used for a long time you should run the water for a few minutes before connecting the inlet hose Do not use for connection old hoses which have been used with another appliance The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations Installation instructions Water inlet hose with safety valve After connecting the double walled water inlet hose the safety valve is next to the tap Therefore the water inlet hose is only under pressure while the water is running If the water inlet hose starts to leak during this operation the safety valve cuts off the running water Please take care when installing the water inlet hose The electrical cable for the safety valve is in the double walled water inlet hose Do not immerse the water inlet hose or the safety valve in water If water inlet hose or the safety valve is damaged remove the mains plug immediately A water inlet hose with safety valve must only be replaced by a specialist or by the Service Force Centre Place the water inlet hose in such a way that it is never higher than the bottom edge of the safety valve 43 Installation instructions 44 Water outlet hose connection The end of the drain hose can be connected in the following ways 1 To the
33. sink outlet spigot securing it to the underside of the work surface This will prevent waste water from the sink running into the machine 2 To a stand pipe provided with vent hole minimum internal diameter 4 cm The waste connection must be at a maximum height of 60 cm from the bottom of the dishwasher The drain hose can face either to the right or left of the dishwasher Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water The sink plug must not be in place when the machine is draining as this could cause the water to syphon back into the machine The total length of the drain hose including any extension you might add must be no longer than 4 metres The internal diameter of the extension hose must be no smaller than the diameter of the hose provided Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided Attention Our appliances are supplied with a security device to protect against the return of dirty water back into the machine If the spigot of your sink has a no return valve incorporated this can prevent the correct draining of your dishwasher We advise you therefore to remove it Installation instructions Electrical connection This appliance must be earthed The manufacturer declines any responsibility should this safety measure not be observed If the plug tha
34. t hose connection Electrical connection Hints for test centres Operating instructions A Safety instructions iJ The safety of AEG electrical appliances conforms to accepted rules of technology and the Appliance Safety Act We as manufacturers however see ourselves as being obliged to familiarise you with the following safety instructions It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information This information has been provided in the interest of your safety You MUST read it carefully before installing or using the appliance If you are unsure about any aspect of the information in this book please contact our customer care department on 08705 950 950 Installation Check your dishwasher for any transport damage Never connect a damaged machine If your dishwasher is damaged you should contact your supplier e For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way e Any electrical and plumbing work required to install this appliance should be carried out by a qualified and competent person Care must be taken to ensure that
35. t is fitted to your appliance is not suitable for the socket it must be cut off and the appropriate plug fitted Important The wires on the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live If you fit your own plug the colours of the wires in the mains lead of your appliance may not correspond with the markings identifying the terminals in your plug Proceed as follows 1 Connect the Green and Yellow earth wire to the terminal in the plug which is marked with the letter E or the earth symbol or coloured green and yellow 2 Connect the Blue neutral wire to the terminal in the plug which is marked with the letter N or coloured black 3 Connect the Brown live wire to the terminal in the plug which is marked with the letter L or coloured red GREEN amp YELLOW CORD CLAMP CE04 45 Installation instructions 46 The plug moulded onto the lead incorporates a 13amp BSI362 fuse Only ASTA or BSI fuses should be used The plug must not be used if the fuse cover carrier is lost The cover carrier is indicated by the coloured insert at the base of the plug A replacement cover carrier must be obtained from your local Service Force Centre To isolate the dishwasher from mains remove the mains plug Important The plug must still be accessible after the appliance has been installed
36. tally in opposite directions and pull them apart To reassemble reverse the procedure 21 Operating instructions 22 The upper basket The upper basket is designed for cups long and or sharp items of cut lery such as carving knives QO SS US84 JAN Before closing the door ensure that the spray arms can rotate freely Operating instructions Use of detergent Only use detergents specifically designed for use in dishwashers We recommend the use of Finish detergents Using no more than the correct amount of detergent contributes to reducing pollution Please observe the manufacturer s dosing and storage recommendations as stated on the detergent packaging Fill with detergent 1 If the lid is closed press release button 1 The lid springs open 2 Fill the detergent dispenser 2 with detergent The marking indicates the dosing levels 20 approximately 20 g of detergent 30 approximately 30 g of detergent DE19 3 All programmes with prewash need an additional detergent dose 5 10 g that must be placed in the prewash detergent chamber 3 This detergent will take effect during the prewash phase 4 Close the lid and press until it locks in place 23 Operating instructions 24 Different kinds of detergent
37. the amount of soil on the dishes is determined by how cloudy the water is If the appliance is partially loaded and the dishes lightly soiled the prewash main wash and rinse phases of the programme are shorter and the water consumption level is lower If the appliance is fully loaded and the dishes heavily soiled the prewash main wash and rinse phases of the programme are longer and the water consumption level is higher For this reason the programme duration water and energy consumption levels can vary within the stated range for AUTOMATIC programme see Washing programmes chart During the AUTOMATIC programme the temperature of the main wash water is also automatically adjusted between 50 C and 65 C depending on the amount of soil on the dishes 26 Operating instructions Starting a washing programme In this fully integrated appliance the controls are located on the top of the door When selecting a programme the door needs to be open 1 Check that the baskets have been loaded correctly and that the spray arms can rotate freely 2 Turn on the water tap 3 Press the On Off button The indicator lights of the programme selection buttons illuminate 4 Setting and starting the programme To select a programme press the button of the programme you wish to select see Washing programmes chart The corresponding indicator light remains illuminated while the other programme buttons indicator lights
38. their lives Therefore cut off the power supply cable and make the door closing device unusable to prevent children from being trapped inside For the disposing of the appliance please take it to a recycling centre or to your dealer who may for a small contribution to the costs dispose it for you The symbol X on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 8 Economical and ecological dishwashing e Ensure that the water softener is correctly adjusted e Do not pre wash under running water Select the wash programme to suit the nature and degree of the soiling on the dishes e Do not use more detergent dishwasher salt and rinse aid than is recommended in these operating instructions and by the manufacturer of the respective product Operating instructions Description of the appliance IN170 7 Internal lights Upper basket Water hardness
39. tion you have to cancel the programme setting see chapter Starting a washing programme Cancel a washing programme in progress and then deactivate the 3 in 1 function In this case you have to set a washing programme and eventual options again Operating instructions 10 NOTE if the drying results are not satisfactory it is possible to activate only the rinse aid dispenser The activation deactivation of the rinse aid dispenser can only be possible with the 3 in 1 function active Activation deactivation of the rinse aid dispenser The dishwasher must be switched off When the rinse dispenser aid has been activated also the rinse aid indicator light on the control panel is automatically activated 1 Press the On Off button The indicator lights of the programme Selection buttons will illuminate setting mode If only one programme selection button indicator light is illuminated this means that a washing programme is set The programme must be cancelled press simultaneously function buttons 2 and 3 for about 2 seconds the indicator light of the set programme button starts flashing After about 2 seconds the indicator lights of all the programme selection buttons will illuminate this means that the set washing programme has been cancelled and the machine is now in setting mode Press simultaneously function buttons 2 and 3 until the indicator lights of function buttons 1 2 and 3 start flashing
40. try within Europe then your guarantee moves with you to your new home subject to the following qualifications e The guarantee starts from the date you first purchased your product The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products e This guarantee relates to you and cannot be transferred to another user e Your new home is within the European Community EC or European Free Trade Area e The product is installed and used in accordance with our instructions and is only used domestically i e a normal household e The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliance France Senlis 33 0 344 62 20 13 Germany Nurenberg 49 0 800 234 7378 Italy Pordenone 39 0 800 11 7511 Sweden Stockholm 46 0 20 78 77 50 UK Slough 44 0 1753 219898 Ireland Dublin 353 0 1 4090753 39 Operating instructions Technical specifications Dimensions Width 89 7 cm Height 69 8 73 3 cm Max depth 57 8 cm Max depth with open door 105 cm Max weight of the dishwasher with furniture panel and without load 80 Kg Electrical connection Information on the electrical con
Download Pdf Manuals
Related Search