Electrolux 50740 Dishwasher User Manual
Contents
1. 5 Date of purchase Please note that it will be necessary to provide proof of purchase for any in guarantee service call In guarantee customers should ensure that the chapter headed What to do if has been read as the engineer will make a charge if the fault is not a mechanical or electrical breakdown Customer Care For general enquiries concerning your AEG appliance or for further information on AEG products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www aeghome co uk Customer Care Department AEG Domestic Appliances 55 77 High Street Slough Berkshire SL1 1DZ Tel 08705 350350 Calls may be recorded for training purposes E The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx 14 billion USD in more than 150 countries around the world RJ From the Electrolux Group The world s No 1 choice AEG Hausger te GmbH Postfach 1036 D 90327 N rnberg http www aeg hausgeraete de Copyright by AEG 822 946 104 00 1101 Subject to change without notice2. Operating Instructions Filling with Detergent cs 1 Only use dishwasher detergent Fill with detergent Prior to the start of a wash programme not for the pre wash pro gramme The detergent is released into the wash water during the programme Please observe the manufacturer s dosing and storage recommenda tions as stated on the detergent packaging The detergent compartment is on the inside of the dishwasher door If the lid is closed press release button 1 The lid springs open Fill the detergent dispenser with detergent The markings indicate the dosing levels 20 corresponds to approx 20 ml of detergent 30 corresponds to approx 30 ml of detergent Close the lid and press until it locks into place If the dishes are very heavily soiled put additional detergent into the adjacent chamber 2 This detergent will take effect during the pre wash Gm D W 19 Operating Instructions 20 Bio Wash Programmes and Concentrated Detergents Based on their chemical composition dishwasher detergents can be split into two basic types Conventional alkaline detergents with caustic components Weak alkaline concentrated detergents with natural enzymes The use of BIO wash programmes in conjunction with concentrated detergents reduces pollution and is good for your dishes the BIO wash programmes are specially matched to the so
3. Dessert Dishes and Coffee Service with delicate glasses lightly soiled concentrated detergents y i NORMAL NORMAL 65 BIO 50 4 Pre Wash Pre Wash Main Wash Main Wash Intermediate Intermediate Rinse Rinse Final Rinse Final Rinse Drying Drying iL iL 89 99 min 110 120 min 1 15 1 35 kWh 0 85 1 05 kWh 13 15 litres 13 15 litres QUICK 50 Main Wash Intermediate Rinse Final Rinse 30 min 0 85 kWh 12 litres All Dish Types Used dishes that are being collected in the dishwasher for washing later Pre Wash 10 min lt 0 1 kWh 4 litres 1 During BIO programmes the water is briefly heated to more than 50 C so that the active oxygen becomes effective 2 The various stages in the wash programme have different sounds because the dishes are washed more intensely for short periods during certain stages of the wash programme to improve cleaning 3 The consumption figures were recorded under standard conditions They are intended as a guide only as variations can occur during normal usage 4 Test programme 21 Operating Instructions 22 Start the Wash Programme is 1 o fF ON Check that when the dishes and cutlery are loaded into the dishwasher the spray arms are free to rotate Open the tap fully Shut the door Press the ON OFF button The ON OFF button indicator illuminates Press the programme
4. Before loading the dishes you should Remove all scraps of food Soften remnants of burnt food in pans When loading the dishes and cutlery please note Dishes and cutlery must not impede the rotation of the spray arms Load hollow items such as cups glasses pans etc with the opening downwards so that water cannot collect in the container or a deep base Dishes and items of cutlery must not lie inside one another or cover each other To avoid damage to glasses they must not touch Do not lay small objects e g lids in the cutlery rack Operating Instructions Loading Cutlery Long bladed knives stored in an upright position are a potential hazard N Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket AN Take care when loading or unload ing sharp items such as knives To ensure that all items of cutlery are completely washed you should ts 1 Place the grid insert on the cutlery rack 2 Place short knives forks and spoons in the grid insert with their handles pointing downwards 3 For larger items of cutlery e g a whisk half of the top for the cut p miss lery basket can be left off EE
5. The Multi Display can display the hardness setting to which the water softener is set the start delay that is set how long the current wash programme can be expected to last which fault has occurred on the dishwasher The Indicators have the following meanings g Refill with special salt X6 Refill with rinse aid Prior to using for the first time Prior to using for the first time remove all the clips with which the dish racks are secured for transport Then perform the following steps ts 1 Adjust the water softener 2 Fill with Salt for the Water Softener 3 Fill with Rinse Aid Operating Instructions Adjust the Water Softener cs 1 To avoid the scale deposits on the dishes and in the dishwasher the dishes must be washed with soft i e low lime content water The dish washer therefore has a built in water softener in which tap water from a hardness of 4 d German degree is softened with the aid of special salt You water supplier will be able to inform you on the hardness and hardness range of the water in your area Adjust the water softener to the setting given in the table that corre sponds to the hardness of the water in your area The water softener can be adjusted in 10 steps Water Hardness Adjust Indication on the in d in ppm 2 Range to Hardness Setting Multi Display 41 50 730 900 9 H9 35 40 630 720 8 H8 31 34 550 620 IV 7 H7 27 30 480 540 6 H6 23 26 410 470 5 H5 19 22 3
6. col oured black e The wire coloured brown must be connected to the terminal marked L or coloured red Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath WARNING A cut off plug inserted into a 13 amp socket is a seri ous safety shock hazard Ensure that if it is necessary to cut off the plug it is disposed of safely and not retained 35 Installation and Connection Instructions 36 Connections The water inlet and drain hoses as well as the mains cable must be connected beside the dishwasher as there is insufficient space behind the appliance The plumbing and electrical installation example given below can only be regarded as a recommendation Two 45 or Straight Connections Outer 19 mm Length 30 mm Double tap Water drain Water inlet Water Mains Water Mains socket Mains inlet cable drain cable Guarantee Conditions GUARANTEE CONDITIONS Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance 1 The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser which must be verified by purchase invoice or similar doc umentation The guarantee does not cover commercial use 2 The guarantee
7. inlet for soiling clean if necessary Operating Instructions Open the door remove the lower The dishwasher filter system com Turn the handle about 1 4 a turn anti Take hold of the coarse fine filter 1 Clean all filters thoroughly under Remove the flat filter 3 from the Put the flat filter back in the base of Place the coarse fine filter in the Put the filter combination in place Cleaning the Filter The filters should be checked and cleaned regularly Blocked filters will give poor wash results rack prises a coarse fine filter microfilter and a flat filter Unlock the filter sys tem using the handle on the microfil ter and remove clockwise and remove by the handle with the hole and remove from the microfilter 2 running water base of the washing compartment and clean both faces thoroughly the washing compartment microfilter and press together and lock by turning the handle clock wise to the stop During this process ensure that the flat filter does not protrude above the base of the wash ing compartment The dishwasher must not be used without filters under any circum stances 25 Operating Instructions 26 What to do if Try to rectify minor faults on the dishwasher with the aid of the instructions given here If you call an engineer to resolve a of fault listed here or to repair a fault caused by incorrect use or instal
8. 30 400 TT 4 H4 15 18 260 320 3 H3 11 14 190 250 II 2 H2 4 10 70 180 ul 1 H1 0 under 4 under 70 l HO no salt necessary 1 d German degree measure of the hardness of water 2 ppm Parts Per Million factory setting The dishwasher must be switched off Press the function and water softener buttons simultaneously and keep them pressed In addition press the ON OFF switch The LED indicators for the function and water softener buttons flash Press the softener button again The multi display indicates the hardness setting Pressing the water softener button increases the hardness setting by 1 Exception hardness setting 0 follows hardness setting 9 Operating Instructions 6 When the hardness setting is correct press the ON OFF switch The hardness setting is then saved Filling with Salt for the Water Softener Use only salt designed for dishwashers Never fill the salt container with any another type of salt e g culinary salt or dishwasher deter gent as this would irreparably damage the water softener Prior to filling with salt please check each time that you really do have a packet of dishwasher salt in your hand Fill with dishwasher salt Prior to using the dishwasher for the first time When the SALT indicator S on the control panel is illuminated If the water hardness in your area is less than 4 d you do not need to use dishwasher salt The SALT indicator S on the cont
9. A IT DAN EDSS h ERES my paR mimm MI IR 55 Doma EIE ix EDD onary EB ECL Seas set ESSE UW REEN a On some models of dishwasher it is possible to open the cutlery basket AN To ensure that the cutlery rack cannot open on removal from the appliance you should always hold both parts of the two part handle t 1 Place the cutlery rack on a table or work surface 2 Open the two part handle 3 Remove cutlery 4 Close the two part handle 15 Operating Instructions i pe Loading Pans Frying Pans and Large Plates Load large and heavily soiled dishes in the lower rack To ease the loading of large items at some dishwasher models the two rows of prongs for the right hand plate insert can be folded down 1 Slightly lift the right plate insert 2 Fold the plate insert to the left A A 3 0 3 i N 0 3 Al 0 n CLEA LEE E E E 3 7 A 3 d j 0 3 A 0 D D Operating Instructions Loading Cups Glasses and Coffee Services Load small delicate items and long pointed cutlery in the upper rack Arrange items of crockery on the folding cups racks so that they are Offset from each other and water can reach all items he cup racks can be folded up out of the way for tall ite
10. FAVORIT 50760 Dishwasher User Instructions Dear customer Please read these user instructions carefully Please observe the safety instructions on the first few pages of these user instructions Please keep these user instructions for later reference Pass them on to any subsequent owner of the appliance The warning triangle and or specific words Warning Caution Important are used to highlight instructions that are important for your safety or for the function of the appliance It is imperative that these instructions are observed This symbol or numbered instruction steps lead you step by step through the operation of the appliance Next to this symbol you receive additional information and practical tips on using the appliance Tips and instructions for the economical and environmentally conscious use of the appliance are marked with a clover leaf In the event of a malfunction these operating instructions contain information on how to rectify faults yourself see the What to do if section If these instructions are insufficient please contact your AEG Service Force Centre In this respect please read the chapter Service amp Spare Parts Printed on paper manufactured with environmentally sound processes He who thinks ecologically acts accordingly Contents CONTENTS Operating Instructions cc cece eee eee ees 5 Safety Instru
11. Instructions Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test programme see Programme Table Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme see Programme Table Full Load 12 place settings incl serving dishes Detergent Dosing 5g 25g Type B Rinse Aid Setting 4 Type III Sample loading arrangements ere AAS A Half Load 6 place settings incl serving dishes leaving alternate positions free 20g Type B 4 Type III DOO emi CURA e CA SERV M 29 Installation and Connection Instructions 30 INSTALLATION AND CONNECTION INSTRUCTIONS Installing the Dishwasher e The dishwasher must be installed on a firm floor and adjusted such that it is stable and level To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units extend the threaded feet by unscrew ing use a screwdriver et Quee LM SS For built in integrated and fully integrated dishwashers the rear feet should be adjusted from the front of the appliance usi
12. ace 6 If rinse aid has run out wipe up with a cloth Daily Use e Check the salt and rinse aid levels Load cutlery and dishes into the dishwasher e Fill with dishwasher detergent e Select a wash programme suitable for the cutlery and dishes e Start the wash programme 13 Operating Instructions 14 Loading Cutlery and Dishes AN Sponges household cloths and any object that can absorb water should not be washed in the dishwasher For washing in the dishwasher the following cutlery dishes are not suitable Cutlery with wooden horn china or mother of pearl handles Plastic items that are not heat resistant Older cutlery with glued parts that is not temperature resistant Bonded cutlery items or dishes Pewter or copper items Lead crystal glass Steel items subject to rusting Wooden platters Items made from synthetic fibres are of limited suitability Only wash stoneware in the dishwasher if it is specifically marked as being dishwasher safe by the manufacturer Glazed patterns may fade if machine washed frequently Silver and aluminium parts have a tendency to discolour during washing Left overs e g egg white egg yolk and mustard often cause discolouring and staining on silver Therefore always clean left overs from silver immediately if it is not to be washed straight after use Some types of glass can become dull after a large number of washes
13. aining water in the appliance is automatically pumped out The AQUA CONTROL SYSTEM also works when the appliance is switched off the appliance must however not be disconnected from the mains Installation and Connection Instructions Electrical Connection AN Any electrical work required to install this appliance should be car ried out by a qualified electrician or competent person WARNING This appliance must be earthed The manufacturer declines any responsibility should these safety measures not be observed Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate To isolate the dishwasher from the mains remove the mains plug Important The plug must still be accessible after the appliance has been installed Changing a fuse The appliance is supplied with a 13amp plug fitted In the event of hav ing to change the fuse in the plug supplied a 13amp ASTA approved BS 1363A fuse must be used Should the plug need to be Green replaced for any reason proceed as amp Yellow described below The wires on the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live The wire coloured green and yellow must be connected to the termi nal marked with the letter E or by the earth symbol or coloured green and yellow The wire coloured blue must be connected to the terminal N or
14. are and Cleaning cece cece 24 Cleaning the Filter ess oci depend awa Dni Rr oe Ee 25 What to do If ae aies eee eae eee eee DUE a ns 26 3ErrOr messages fas serere ba erre Rp le abe d e PG ad 26 there are problems with the operation of the dishwasher 27 the wash results are not satisfactory 0 cece eee ee eee 27 Contents Technical Data oe Rees 28 Notes for Test Institutes ssssusssse RR 29 Installation and Connection Instructions 30 Installing the Dishwasher seeeeeee BR 30 Dishwashers That Can Be Integrated eee eee 31 Connecting the Dishwasher sss 32 Water Connection zx cune ed hae iex e Im Ru e EDEN Y Du 32 Permitted water pressure eee ees 32 Connect the inlet hose seins eee eee ee 32 Mater dralm ess xr anm mei e a e a Tee rn 33 Leak Prevention System 00 cece cece eens 34 Electrical Connection 0 cece ccc IRR 35 CONNECTIONS scere ode rx oce eb epo E ICE nee EAS Seed e erie 36 Guarantee Conditions 37 Service amp Spare parts ok ood esie Ente RIEN redet e 39 Operating Instructions OPERATING INSTRUCTIONS Safety Instructions The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law Neverthe less as a manufacturer we consider it our obligation to make you aware of the follow
15. asher Hot steam may escape from the appliance when opening the door Open the door carefully Open the door of the dishwasher The wash programme stops The indicator for the programme that is currently running extinguishes Close the door The wash programme continues Cancelling the wash programme Press the button for the current wash programme and hold it pressed The programme indicator for the current wash programme flashes for a few seconds and then extinguishes Release the programme button the wash programme is cancelled A selected programme is only interrupted by switching off the dish washer it is not cancelled The wash programme is continued when the dishwasher is switched on again Setting or Changing the Delay Start Timer Using the delay start timer you can delay Setting the delay start timer Press the ON OFF button delay is flashing on the multi display Press the button for the desired wash programme The multi display now displays the number of hours without flashing The number of hours is saved he wash programme starts automatically at the end of the delay set Changing the delay start As long as the wash programme has not started you can still change the delay start set by pressing the DELAY TIMER button Q 23 Operating Instructions Load Sensing Sensor Logic If a wash programme is started even though there are only a few dishes in the upper and or lower ra
16. button for the desired programme see Pro gramme Table The programme indicator illuminates The selected programme begins after around 6 seconds The time remaining until the end of the programme is displayed on the multi display the time calculated is dependent on the load in the dish racks With automatic programme adjustment this residual time count can be stopped or corrected if necessary load quantity degree of dirtiness etc using the dishwasher control If fault messages are displayed on the multi display after the start of the programme please read the What to do if section Changing Interrupting Cancelling the Wash Programme Only change or interrupt a wash programme in progress if it is abso lutely necessary to do so Changing the wash programme If you want to change the wash programme within 6 seconds of mak ing a programme selection briefly press the button for the new wash programme If you want to change the wash programme at a later point in time use the following procedure Press the button for the new wash programme and hold it pressed The indicators for both programmes now flash After a few seconds only the indicator for the new programme flashes Release the programme button the new programme is now running Operating Instructions p 1 Keep pressing the DELAY TIMER button Q until the number of hours of Interrupting the wash programme by opening the door of the dishw
17. ck an intelligent electronic system adjusts the amount of water and the duration of the wash programme to the number of dishes By this means it is possible to wash only a few dishes quickly and economically At half load 6 place settings up to 2 litres of water and 0 2 kWh of electricity are saved Switching Off the Dishwasher Switch the dishwasher off when the multi display indicates 0 for the remaining programme time Press the ON OFF button The ON OFF button indicator extinguishes Hot steam may escape from the appliance when opening the door immediately after the end of the programme Open the door carefully as steam may escape Emptying the Dishwasher e The dishes should therefore be allowed to cool down before removing them from the appliance as hot dishes can be sensitive to knocks Leave the dishes in the dishwasher for approx 15 minutes after the end of the programme so that they dry better and can cool down First empty the lower rack and then the upper rack This will avoid any water that may be remaining in the upper rack dripping onto the dishes in the lower rack and leaving water marks Care and Cleaning AN 24 Do not under any circumstances use furniture care products or aggres sive cleaners f necessary clean the controls only with a soft cloth and pure warm water e The spray arms do not need cleaning Occasionally check the internal containers door seal and water
18. covers all parts or components which fail due to faulty workmanship or faulty materials The guarantee does not cover appliances where defects or poor per formance are due to misuse accidental damage neglect faulty installation unauthorised modification or attempted repair commercial use or failure to observe requirements and recommendations set out in the instruction book This guarantee does not cover such parts as light bulbs removable glassware or plastic dust bags or filters 3 Should guarantee repairs be necessary the purchaser must inform the nearest customer service office manufacturer s service or authorised agent AEG reserves the right to stipulate the place of the repair i e the customer s home place of installation or AEG workshop 4 The guarantee or free replacement includes both labour and materials 5 Repairs carried out under guarantee do not extend the guarantee period for the appli ance Parts removed during guarantee repairs become the property of AEG 6 The purchaser s statutory rights are not affected by this guarantee European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications The guarantee starts from the date you first purchased your product The guarantee is for the same period and to the same extent for labour and parts as exist in the new country of use for this brand or range of produc
19. ctions 2 eciceise Eee Pe ee hee ee 5 Disposal cea ir eee DATES eee Ua ans WGA oe ee E 7 Economical and Ecological Dishwashing 7 Appliance Features and Control Panel 8 Control pariel ts seb RERUM UE DORREUPE RERERESA 9 Prior to using for the first time 0 0 00 cece eee 9 Adjust the Water Softener sssssssessssssees nnna 10 Filling with Salt for the Water Softener 0 eee eee eee 11 Filling with Rinse Aid irure ek ened ran cies 12 Adjusting Rinse Aid Dosing 02 cece cece eens 13 In Daily Use re mtd 13 Loading Cutlery and Dishes lsssssesseessseeesRR 14 Loading Cutlery sz mer Pe e fea ea Deve e E x es 15 Loading Pans Frying Pans and Large Plates 16 Loading Cups Glasses and Coffee Services 22000000000ee 17 Adjusting the Height of the Upper Basket ssusue 18 Filling with Detergent 0 eee eee eee 19 Bio Wash Programmes and Concentrated Detergents 20 Selecting the Wash Programme Programme Table 21 Start the Wash Programme sssssssseee ne 22 Changing Interrupting Cancelling the Wash Programme 22 Setting or Changing the Delay Start Timer 2 0 23 Load Sensing Sensor Logic 0 cece cece 24 Switching Off the Dishwasher 0 c cece eee eens 24 Emptying the Dishwasher 0 0 cece ees 24 C
20. il dissolving properties of the enzymes in the concentrated detergent It is for this reason that BIO wash programmes can achieve the same results at 50 C that can otherwise only be achieved using 65 C programmes During BIO programmes the water is briefly heated to more than 50 C so that the active oxygen becomes effective Detergent tablets from different manufacturers dissolve at different rates For this reason some detergent tablets cannot develop their full cleaning power during short programmes Therefore please use normal programmes with pre wash when using detergent tablets Detergent Recommendations For best results we recommend the use of Finish detergent rinse aid and salt Operating Instructions Selecting the Wash Programme Programme Table Choose the most suitable wash programme with the aid of this table Type of Dishes In Addition Type of Soiling Suitable Programme Programme Sequence a Consump tion Figures 3 Duration Energy Water Dinner Service and Cooking Utensils heavily soiled dried on left overs partic ularly egg white and thickeners INTENSIVE 70 Pre Wash Main Wash 2x Intermedi ate Rinses Final Rinse Drying i 110 120 min 1 9 2 1 kWh 18 20 litres with non tem perature resist ant dishes normally normally soiled soiled dried left overs particularly suited to the use of
21. ing safety information Installation Connection and Placing into Operation e The dishwasher may only be transported upright e Check the dishwasher for transport damage Do not in any circum stances connect an appliance that is damaged In the case of damage please contact your retailer Before installing the appliance ensure that the nominal voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed The fuse rating is also to be found on the rating plate For information on how to correctly install and connect up your dish washer please read the Installation section Adaptors connectors and extension cables must not be used Child Safety his appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the product Keep all packaging away from children e Keep all detergents in a safe place out of children s reach The water in your dishwasher is not suitable for drinking If there are still remnants of detergent in the appliance there is a risk of burns When disposing of an old appliance cut off the power supply cable and remove any door catches to prevent young children being trapped inside General Safety Repairs to the dishwasher are only to be carried out by qualified serv ice engineers Improper repairs can give rise to significant hazards for the user If your appliance needs repai
22. k of an explo sion e The anti flood system provides dependable protection against dam age due to leaks For this system to function correctly the following preconditions must be met he appliance must remain connected to the mains even when it is switched off The dishwasher must be correctly installed Always shut off the water supply at the tap when the dishwasher is not to be used for longer periods e g when you are away on holiday Do not sit or stand on the open door the appliance may tip over Operating Instructions e n the event of a fault first close the tap then switch off the appli ance and unplug it from the mains If the appliance is permanently wired to the mains remove the fuse Disposal Disposing of the Packaging Material Dispose of the dishwasher packaging material correctly All the packag ing materials used are harmless to the environment and can be recy cled Plastic parts are marked with standard international abbreviations PE for polyethylene e g sheet wrapping material PS for polystyrene e g padding material always CFC free POM for polyoxymethylene e g plastic clips e Cardboard packaging is manufactured from recycled paper and should be deposited in the waste paper collection for recycling Disposal of Old Appliances When disposing of old appliances remove the plug and ensure that any locks or catches are removed to prevent young children becoming
23. lace fuse If the dishes are to be washed immediately set the start delay to 0 hours Only wash cutlery and dishes that are suitable for dish washer use Close the lid of the special salt container securely Use a different brand of detergent 27 Operating Instructions There are streaks milky spots or a bluish coating on glasses and dishes Lower rinse aid dosing There are dried water drops on the glasses and dishes Increase rinse aid dosing The detergent may be the cause Contact the detergent manufac turer s customer advisor Technical Data Capacity 12 place settings including serving dishes Permitted Water 10 2E Pressure 1 10 bar 210 100 N cm 0 1 1 0 MPa Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door on the right Electrical Connection Dishwasher Free Standing Appliances Dimensions 850 x 600 x 600 H x W x D in mm Max Weight 54 Kg Dishwashers that Can Be Integrated Built In Dishwashers Dimensions 820 880 x 596 x 570 H x W x D in mm Max Weight 50 Kg Dishwashers that Can Be Fully Integrated Dimensions 820 880 x 596 x 546 550 H x W x D in mm Max Weight 50 Kg C This appliance conforms with the following EU Directives 73 23 EWG dated 19 02 1973 Low Voltage Directive 89 336 EWG dated 03 05 1989 including Directive Amendment 92 31 EWG EMC Directive Operating
24. lation a charge will be made even if the appliance is in guarantee Error messages e f the programme indicator for the selected wash programme is flashing and fault code E i you can probably rectify the fault yourself I or Ce is displayed on the multi display After rectifying this fault press the button for the wash programme that has been started The wash programme continues If the fault code is displayed again contact customer service For all other faults please contact customer service stating the fault code Symptom Fault code tis dis played on the multi display The programme indica tor for the selected wash programme is flashing there is no water run ning into the dish washer Fault code E is dis played on the multi display The programme indica tor for the selected wash programme is flashing Fault code 3 is dis played on the multi display Possible Cause Tap is blocked or furred with lime scale The filter where present in the threaded hose fitting is blocked The water inlet hose is not correctly laid The sink outlet is blocked The water drain hose is not correctly laid The leak prevention system has been triggered Solution Clean tap Clean the filter in the threaded hose fitting Check hose installation Clean the sink outlet Check hose installation Close the tap and contact your local AEG Sevice Force Centre Ope
25. ler if the water pres 1 bar 10 N cm 100 kPa sure is less than 1 bar Highest permitted water pressure In the case of a water pressure greater 10 bar 2100 N cm 1 MPa than 10 bar a pressure reduction valve must be used available from your dealer Connect the inlet hose The water inlet hose must not be kinked crushed or entangled when it is being connected up Connect the threaded hose fitting ISO 228 1 2000 on the water inlet hose to a tap with an external thread 34 inch Tighten the threaded hose fitting hand tight only n order that access to the tap in the kitchen is not limited by the use of the dishwasher we recommend the installation of an additional tap or fitting a two way adapter to the existing tap e f you need a longer water inlet hose than that supplied VDE approved complete hose sets are to be used These are available from your local Service Force Centre Installation and Connection Instructions Water drain Drain hose The drain hose must not be kinked crushed or entangled Connecting the drain hose Maximum permitted height 1 metre Minimum required height 30 cm above the lower edge of the machine Extension hoses e Extension hoses are available from i AEG Service Force The internal F diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not E impeded e 4 Hoses may be laid a maximu
26. ly open the rinse aid compartment lid x Gv C o Rinse aid is automatically added during the last rinse ensuring thor ough rinsing spot and streak free drying Only use rinse aid specifically designed for domestic dishwashers Never fill the rinse aid container with any other substance as this would dam age the appliance Fill with rinse aid Prior to using the dishwasher for the first time When the RINSE AID indicator 3 amp on the control panel is illuminated The rinse aid compartment is on the inside of the dishwasher door release button with your finger l Ale Operating Instructions i In 4 Fill with rinse aid exactly up to the level marked max this corresponds to a quantity of approx 140 ml 5 Close the lid and press until it locks into place 6 Wipe up any spilt rinse aid with a cloth Otherwise too much foam will be formed during the wash Adjusting Rinse Aid Dosing As the dishes are washed rinse aid is released from the dispenser into the wash water The dose is factory set at 4 and can be adjusted from 1 to 6 Only change the setting if streaks milky spots or dried on water marks are visible on glasses or crockery 1 Open the door of the dishwasher 2 Press the rinse aid compartment release button with your finger 3 Fully open the rinse aid compartment lid 4 Set the dose level 5 Close the lid and press until it locks into pl
27. m of 3 3 metres horizontally the maximum P I permitted height for the connection S for the drain hose is then 85 cm V 0m p Sink outlet connection e The outlet of the drain hose 19 mm fits all commonly available sink outlet spigot types The outer diameter of the spigot connection must be at least 15 mm e The drain hose must be fixed to the sink outlet connection using the hose clamp supplied If the dishwasher is fitted at a high position If the dishwasher is installed at a high level and the drainhose connec tion is less than 30 cm from the bottom of the appliance adapter kit ET 111099520 must be fitted This is available from Customer Service Discharging into a standpipe When discharging into a standpipe the upright standpipe should have a minimum length of 30 cm 12 from the bottom of the elbow to the top of the pipe see diagram Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water Min 38mm 12 diameter standpipe Min 30 cm 12 33 Installation and Connection Instructions AN 34 Leak Prevention System For protection from damage due to water leaks the dishwasher is equipped with a leak prevention system the AQUA CONTROL SYSTEM In the event of a fault the safety valve immediately interrupts the sup ply of water to the appliance and the drain pump switches on By this means water can neither escape nor overflow The rem
28. ms Lay or hang wine champagne and brandy glasses in the cut outs on the cup racks Glasses beakers etc can also be placed on the two rows of prongs on the left of the upper rack ll 17 Operating Instructions Adjusting the Height of the Upper Basket Maximum Height of the Dishes in the Upper Basket Lower Basket With upper basket raised 22 cm 31 cm With upper basket lowered 24 cm 29 cm il The height of the basket can also be adjusted when it is loaded Depending on the model your appliance is provided with one of the following types of upper basket Lowering the Upper Basket Type 1 ts 1 Pull the upper basket out completely 2 Lift the upper basket at the rear right and lower Raising the Upper Basket ts 1 Pull the upper basket out completely 2 Raise the upper basket at the rear right pull slightly forward and allow to lock into place in the upper posi tion Lowering the Upper Basket ts 1 Pull the upper basket out completely 2 Holding the upper basket at the rear right lift it as far as it will go and then lower it vertically The upper basket will engage in the lower posi tion Raising the Upper Basket ts 1 Pull the upper basket out completely Holding the upper basket at the rear right lift it as far as it will go and then lower it vertically The upper basket will engage in the higher posi tion N
29. ng a screwdriver The drain hose inlet hose and mains cable must be laid such that they are free to move in the rear of the plinth recess so that they cannot be kinked or crushed he dishwasher must also be screwed on tightly to the work surface or to the adjoining units This is absolutely necessary so that its sta bility is guaranteed according to VDE regulations Installation and Connection Instructions Dishwashers That Can Be Integrated see installation template supplied The door of the appliance can be fitted with a wooden facing panel with the following dimensions Width 591 594 mm Thickness 16 24 mm Height dependenton Aperture height variable Plinth height The adjustment so that the unit matches the height of the adjoining units The exact height of the adjoining units must be measured at the place of installation Weight max 8 kg 31 Installation and Connection Instructions 32 Connecting the Dishwasher Water Connection 3 gt The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations e The dishwasher can be connected to cold and hot water supplies up to max 60 C e The dishwasher must not be connected to open hot water appliances or instantaneous water heaters Permitted water pressure Lowest permitted water pressure Consult your instal
30. rating Instructions there are problems with the operation of the dish washer Symptom The programme does not start Rust spots are visible in the washing compart ment There is a whistling noise during washing the wash results are not satisfactory Possible Cause The door of the dishwasher is not closed properly Mains plug is not plugged in House fuse is defective A start delay is selected The washing compartment is made from rust free stainless steel Rust spots in the wash ing compartment are due to rust particles from external sources rust particles from water pipes pans cutlery etc Remove such spots with one of the stainless steel cleaners that are generally available on the market The whistling is not a cause for concern The dishes are still dirty The wrong wash programme was selected The dishes were loaded is such a way that the wash waster did not reach all items The racks for the dishes must not be overloaded The filter in the base of the washing compartment is dirty or incor rectly positioned Detergent was not used or too little was used In the case of scale deposits on the dishes The special salt container is empty or the water softener is incorrectly adjusted The drain hose is incorrectly laid The dishes are wet and dull Rinse aid was not used The rinse aid container is empty Solution Shut the door Insert mains plug Rep
31. ring please contact your local AEG Service Force Centre Operating Instructions Never place the dishwasher in operation if the mains cable water inlet or drain hose is damaged or the control panel work top or plinth area is damaged such that the inside of the appliance is freely accessible e f the mains lead is damaged or is to be replaced for a longer lead the cable obtainable from AEG Service Force must be replaced by a service engineer authorised by AEG Never unplug the appliance by pulling on the cable always pull the plug Additions or modifications to the dishwasher are not permitted for safety reasons Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded In this way you will avoid anybody tripping over the open door and hurting themselves Long bladed knives stored in an upright position are a potential haz ard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket e When finished loading or unloading close the door as an open door can be a hazard Correct Use Only wash household dishes using the dishwasher If the appliance is used for other purposes or is used incorrectly the manufacturer can not accept any liability for any damage caused Only use detergents specifically designed for use in domestic dish washers Do not put any solvents in the dishwasher There is a ris
32. rol panel will remain illuminated 1 Open the door remove the lower rack 2 Undo the lid on the salt container by turning it anticlockwise 3 When using for the first time fill the salt container with water 4 Place the funnel supplied on the con tainer opening Fill the container with salt through the funnel the capacity of the con tainer is approx 1 0 1 5 kg depend ing on the grain size Do not overfill the salt container with salt The water expelled by filling the salt container with salt runs out of the salt container onto the base of the washing compartment This is not a cause for concern the water will be pumped out at the start of the next wash programme Clean any salt remnants on the container opening Turn the lid clockwise to the stop otherwise dishwasher salt will leak into the wash water this could lead to poor wash results To avoid this run a rinse programme after filling the salt container with special salt This will wash away salt water and any salt crystals that have been spilt o 11 Operating Instructions i Depending on the size of the salt grains it can take several hours for the salt to dissolve in the water and the special salt indicator S to extinguish The setting of the water softener and the consumption of salt are dependent on the hardness of the local water Filling with Rinse Aid AN Open the door Press the rinse aid compartment Ful
33. trapped inside Use an authorised disposal site Economical and Ecological Dishwashing Ensure that the water softener is correctly adjusted Do not pre rinse dishes under running water e When you wash a small load the load sensor calculates the amount of water necessary and shortens the programme It is more economi cal to always wash with a full load e Select the wash programme to suit the nature and degree of the soil ing on the dishes Do not use more detergent special salt or rinse aid than is recom mended in these operating instructions and by the detergent manu facturer Operating Instructions Appliance Features and Control Panel Top Spray y Nozzle Rubber Seal for Connecting the Water Feed to the Upper Spray Arm Spray Arms Container for Salt Container for Rinse Aid Detergent Dispenser Rating Filters Plate Operating Instructions Control panel Function Softener Set Button Button Door Handle Start Delay Indicators O1O ses Q INTENSIVE J Q Quick j Q iQ DO Control Field Multi Display The Control Field comprises the ON OFF switch and the programme buttons with LED indicators Softener and Function Button in addition to the wash programme marked it is also possible to adjust the dishwasher s water softener using the combination of these buttons
34. ts This guarantee relates to you and connot be transferred to another user Your new home is within the European Community EC or European Free Trade Area The product is installed and used in accordance with our instructions and is only used domestically i e a normal household The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care Centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 44 62 29 29 Germany N rnberg 49 0 911 323 2600 Italy Pordenone 39 0 1678 47053 Sweden Stockholm 46 0 8 738 7910 UK Slough 44 0 1753 219899 38 Service amp Spare parts SERVICE amp SPARE PARTS If you wish to purchase spare parts or require an engineer contact your local AEG Service Force Centre by telephoning 08705 929 929 Your telephone call will be automatically routed to the Service Centre covering your post code area When you contact the Service Centre they will need the following information Your name amp address including post code Your telephone number Clear and concise details of the fault The model serial and production number This information can be found on the rating plate The rating plate is on the inner edge of the door on the right Po NS
Download Pdf Manuals
Related Search