Echo 99944200610, SRM-2100SB, SRM-2400SB, SRM-210SB, SRM-211SB, SRM-260SB, SRM-261SB, PAS-2100, PAS-2400, PAS2601, PAS-210, PAS-211, PAS-230, PAS-231, PAS-260, PAS
Contents
1. 6 MECHO EQUIPMENT Before operation a complete check of the unit must be performed Check unit for loose missing nuts bolts and screws Tighten and or replace as needed Inspect shield for damage and ensure that cut off knife is securely in place Replace if shield is damaged or missing Check that the cutting attachment is firmly attached and in safe operating condition Check that front loop handle and shoulder strap or shoulder waist harness are adjusted for safe comfortable operation See Assembly Section for proper adjustment DESCRIPTION Locate this safety decal on your attachment Make sure the decal is legible and that you understand and follow the instructions on it If it cannot be read a new one can be ordered from your ECHO dealer See PARTS ORDERING instructions for specific information 1 2 89016054130 UNITS 1 LOWERDRIVESHAFT ASSEMBLY Includes the Debris Shield Assembly Gear Housing assembly Flexible Drive Cable Rapid Loader Head and Safety Decals 2 FLEXIBLE DRIVE CABLE Cable end fits into upper drive shaft coupler Lubricate drive cable every 25 hours with ECHO LUBE grease 3 PLASTIC DEBRIS SHIELD ASSEMBLY Included in plastic bag co pack MUST be installed on unit before use see Assembly Instructions Shield assembly includes the Cut Off Knife Mounts on the Gear Housing Assembly just above the cutting attachment Helps protect the operator by deflecting de2. Genuine ECHO Parts and ECHO REPOWER Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer When you do need to buy parts always have the Model Number and Serial Number of the attachment with you You can find these numbers on the driveshaft model serial number label For future reference write them in the space provided below Model Number Model No KIORITZCORP ASSENELEDNUSA SERVICE DEALER Service of this product during the warranty period must be performed Call by an Authorized ECHO Service Dealer For the name and address of the Authorized ECHO Service Dealer nearest you ask your retailer or call 1 800 432 ECHO 3246 When presenting your unit for Warranty 1 800 432 ECHO service repairs proof of purchase is required or ECHO CONSUMER PRODUCT SUPPORT www echo usa com If you require assistance or have questions concerning the application operation or maintenance of this product you may call the ECHO CONSUMER PRODUCT Consumer Product Support Department at 1 800 673 1558 from 8 30am SUPPORT to 4 30 pm Central Standard Time Monday through Friday Before calling please know the model and serial number of your unit to help 1 800 673 1558 your Consumer Product Support Representative 8 30 4 30 Mon Fri C S T WARRANTY CARD This card is our means of registering all original owners of ECHO equipment The card plus proof of purchase provides you the assur ance that authori
3. dexterity may not be good e if you are tired or sick e if you are taking medication if you have taken alcohol or drugs Operate unit only if you are physically and mentally well Eye Protection Wear eye protection that meets ANSI Z87 1 or CE requirements whenever you operate the trimmer Hand Protection Wear no slip heavy duty work gloves to improve your grip on the Trimmer Brush Cutter handles Gloves also reduce the transmission of machine vibration to your hands Hearing Protection ECHO recommends wearing hearing protection whenever unit is used Proper Clothing Wear snug fitting durable clothing Pants should have long legs shirts with long sleeves DONOTWEARSHORTS DONOTWEARTIES SCARVES JEWELRY Wear sturdy work shoes with non skid soles DONOTWEAR OPEN TOED SHOES DONOTOPERATEUNITBAREFOOTED Hot Humid Weather Heavy protective clothing can increase operator fatigue which may lead to heat stroke Schedule heavy work for early morning or late afternoon hours when temperatures are cooler Vibration and Cold It is believed that a condition called Raynaud s Phenomenon which affects the fingers of certain individuals may be brought about by exposure to vibration and cold Exposure to vibration and cold may cause tingling and burning sensations followed by loss of color and numbness in the fingers The following precautions are strongly recommended because the minimum exposure which might trigger
4. the ailment is unknown Keep your body warm especially the head neck feet ankles hands and wrists Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks and also by not smoking Limit the hours of operation Try to fill each day with jobs where operating the trimmer or other hand held power equipment is not required f you experience discomfort redness and swelling of the fingers followed by whitening and loss of feeling consult your physician before further exposing yourself to cold and vibration PAS RaAP D LOADER V TRIMMER ATTACHMENT 5 OPERATOR s MANUAL Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers hands arms and shoulders may cause soreness swelling numbness weakness and extreme pain in those areas Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury RSI An extreme RSI condition is Carpal Tunnel Syndrome CTS which could occur when your wrist swells and squeezes a vital nerve that runs through the area Some believe that prolonged exposure to vibration may contribute to CTS CTS can cause severe pain for months or even years To reduce the risk of RSI CTS do the following Avoid using your wrist in a bent extended or twisted position Instead try to maintain a straight wrist position Also when grasp ing use your whole hand not just the thumb and ind
5. to lock out position 3 Remove vinyl cap from attachment drive shaft 4 Remove cardboard spacer if necessary 5 Carefully fit attachment lower drive shaft assembly into coupler B to decal assembly line C making sure that the inner lower drive shaft engages into the upper drive shaft mount 6 MECHO NOTE Earlier model Power Heads may have shorter couplings Short couplings fit flush to decal point E New couplings are 4 3 4 in long and fit flush to line C NOTE Lower bearing housing and head assembly must be in line with the engine 6 Rotate locator pin A 1 4 turn clockwise to engage lower shaft hole Insure locator pin is fully engaged by gently twistinglower drive shaft Locator pin A should snap flush in coupler Full engagement will prevent further shaft rotation 7 Secure lower shaft assembly to coupler by tightening clamping knob D PLASTIC SHIELD INSTALLATION for Nylon Line Operation NOTE The plastic shield is for use with the Nylon Line Head only Install Metal Shield when using plastic or metal blades 1 Remove plastic threaded shaft sleeve and adapter plate C from PTO shaft A 2 Place the shield on the bottom of the bearing housing flange 3 Place shield plate B on shield align holes Install three 3 screws from bottom through plate and shield into gear case 4 Assemble upper plate C onto PTO shaft PAS RaAP D LOADER V TRIMMER ATTACHMENT OPERA
6. Level Frequency Drive Shaft Grease 1 Every 25 hours of use Gear Housing Grease 1 Every 50 hours of use Screvvs Nuts Bolts Inspect Tighten Replace 1 Before each use LUBRICATION WECHOLUBE Level 1 1 Tools Required 8mm Open End Wrench Screwdriver Clean Rag Parts Required ECHO LUBE N8oz P N 91014 or Lithium Base Grease Gear Housing 1 Clean all loose debris from gear box 2 Remove plug A and check level of grease 3 gear case with grease 4 Install plug A Drive Shaft Lower IMPORTANT Lower and upper drive shaft must be lubricated with ECHO LUBE grease every 25 hours of operation otherwise drive shaft assembly overheating and failure can result PAS RaAP D LOADER V TRIMMER ATTACHMENT 1 1 OPERATOR S MANUAL 1 Loosentwo 2 8 mm upper gear housing bolts B and locator screw C Remove gear case assembly 2 Remove flex cable wipe clean and apply a thin coating 15 ml of grease 3 Install flex cable Make sure cable end engages upper drive shaft adaptor 4 Install gear case assembly onto drive shaft aligning locator screw with hole in drive shaft 5 Tighten two 8 mm bolts B and locator screw C IMPORTANT Flat edge of washers D must be against drive shaft NYLON LINE REPLACEMENT Level 1 Tools Required None Parts Required Pre cut Nylon Line MODELS REQUIREDLINE SIZES SRM 2100SB SRM 210SB 211SB 080 095 in PAS 210 211 PAS 230 231 S
7. MECHO PAS Rapid Loader Trimmer Attachment Operator s Manual MODEL 99944200610 FOR MODELS SRM 2100SB TYPE 1 1E SRM 2400SB TYPE 1 1E SRM 210SB 211SB SRM 260SB 261SB PAS 2100 TYPE 1E PAS 2400 TYPE 1E PAS 2601 TYPE 1E PAS 210 211 PAS 230 231 PAS 260 261 WARNING A DANGER Read rules for safe operation and instructions carefully ECHO provides an Operator s Manual anda Safety Manual with your original Split Boom Pro Attachment Series Trimmer Those manuals and this manual must be read and understood for proper and safe operation X770000332 X7702273502 01 06 2 MECHO NTRODUCTION Welcome to the ECHO family This ECHO product was designed and manufactured to provide long life and on the yob dependability Read and understand this manual and the SAFETY MANUAL you found in the same package You will find both easy to use and full of helpful operating tips and SAFETY messages THE OPERATOR S MANUAL Read and understand this manual before operation Keep it in a safe place for future reference It contains specifications and information for operation and maintenance specific to the attachment f PAS Rapid Loader Trimmer Attach ment 95784 2006 10 Dperaiar r THE SAFETY MANUAL Explains possible hazards and what measures you should take to insure safe operation TABLE OF CONTENTS Maintenance Skill Levels Maintenance Intervals Lubrication Manual Safety Symbols an
8. RM 2400SB 095 130 In SRM 260SB 261SB 095 155 PAS 2601 095 155 in PAS 260 261 095 155 in 1 Insert pre cut 204 mm 8 in length of nylon cutting line recom mended sizes 2 4 mm 095 in to 3 9 mm 155 in through outside openings of trimmer head Minimum of 153mm 6 in of line should extend from each opening 3 9mm 155 in line not recommended for trimmers under 26cc NOTE Insert cutting line ends to center of head recess to insure easy removal of used lines NOTICE Nylon line can damage plastic shield When installing line seg ments make sure line does not curve upward toward shield 12 MECHO STORAGE Storage Hook nstallation 1 Insert small end of hook into locating hole on attachment shaft 2 Slide plastic cap onto end of attachment shaft SPECIFICATIONS PAS Rapid Loader Attachment Shaft Length 838 mm 331n Aftachment VVidth 178mm 7 in Attchment Height 229 mm 9 in Weight dry w blade 1 36kg 3 1 Ib Drive Shaft 6 35 mm 1 4 in Flex Shaft Rotating Direction Counter clockwise viewed from the top Cutter Head Rapid Loader head 2 lines with 095 Cross Fire Line NOTE Install and use U Handle when operating any model with blade PAS RaAP D LOADER V TRIMMER ATTACHMENT 1 3 OPERATOR S MANUAL NOTES 14 TECH NOTES PAS RaAP D LOADER V TRIMMER ATTACHMENT 1 5 OPERATOR S MANUAL NOTES SERVICING NFORMATION PARTS SERIAL NUMBER
9. TOR s MANUAL NYLON LINE HEAD INSTALLATION L Align hole in upper plate with notch in edge of gear housing and insert head locking tool A Remove plastic sleeve from PTO shaft Be sure upper plate B remains on PTO shaft Place line head onto PTO shaft followed by large metal washer C Thread L H nut D on PTO shaft Tighten securely Install new split pin E Remove locking tool A OPERATION NOTE Refer to your Split Boom Pro Attachment Series Operator s Manual for correct engine fueling starting and stopping instructions IMPORTANT Never wear line shorter than 1 1 2 inch extension from head otherwise overspeeding and engine damage may result 9 10 MECHO MAINTENANCE Your ECHO trimmer is designed to provide many hours of trouble free service Regular scheduled maintenance will help your trimmer achieve that goal If you are unsure or are not equipped with the necessary tools you may want to take your unit to an ECHO Service Dealer for maintenance To help you decide whether you want to DO IT YOURSELF or have the ECHO Dealer do it each maintenance task has been graded If the task is not listed see your ECHO dealer for repairs SKILL LEVELS Levell Easy to do Most required tools come with unit Level2 Moderate difficulty Some specialized tools may be required Level3 Experience required Specialized tools are required MAINTENANCE INTERVALS Component System Maintenance Procedure Skill
10. bris produced during the trimming operation This shield must be replaced with the steel shield for blade use 4 CUT OFF KNIFE Trims line tothe correct length 5 RAPIDLOADER HEAD Contains replaceable nylon trimming lines PAS RaAP D LOADER V TRIMMER ATTACHMENT 7 OPERATOR S MANUAL CONTENTS After opening the carton check for damage Immediately notify your retailer or ECHO Dealer of damaged or missing parts Use the contents list to check for missing parts A NITE mi ACER Ric ZAMLARLA LIMITADA Pro Attachment Series Trimmer Attachment Operator s Manual Safety Manual VVarranty Registration Card Locking Tools VVrench 17 x 14 5 Rapid Loader Head Nut Washer 10x32x1 2 Plastic Debris Shield SplitPin Shield plate 5mm x 16mm Screws shield mounting Storage Hook Assembly GO pa m Roe pa me N ra me pr ASSEMBLY WARNING DANGER Do not perform maintenance or assembly procedures vvith engine running Tools Required Screwdriver Head Locking Tool 17x14 5mm Wrench Needle Nose Pliers Parts Required Power Head Shaft Attachment Lower Shaft Assembly Plastic Shield Shield Plate three 3 5mm x 16mm screws Rapid Loader Head POWER HEAD SHAFT ATTACHMENT LOWER SHAFT ASSEMBLY 1 SetPower Head Shaft Assembly on a level surface 2 Pull locator pin A and rotate counter clockwise 1 4 turn
11. d Important Nylon Line Replacement Information Storage International Symbols Specifications Personal Condition and Safety Equipment Servicing Information Equipment Parts Serial Number Description Service Contents ECHO Consumer Product Support Assembly Warranty Card Power Head Shaft Attachment Lower Additional or Replacement Manuals Shaft Assembly Plastic Shield Installation Nylon Line Head Installation Operation Specifications descriptions and illustrative material in this literature are as accurate as known at the time of publication but are subject to change without notice Illustrations may include optional equipment and accessories and may not include all standard equipment Copyright 2006 By Echo Incorporated All Rights Reserved PAS Rapip LOADER V TRIMMER ATTACHMENT OPERATOR S MANUAL SAFETY MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION Throughout this manual and on the product itself you will find safety alerts and helpful information messages preceded by symbols or key words The following is an explanation of those symbols and key words and what they mean to you This symbol accompanied by the words WARNING and DANGER calls attention to an act or condition that can lead to serious personal injury to operator and bystanders IMPORTANT The enclosed message provides information necessary for the protection of the unit The circle with the slash symbol means whate
12. ex finger e Take periodic breaks to minimize repetition and rest your hands Reduce the speed and force with which you do the repetitive movement Do exercises to strengthen the hand and arm muscles Immediately stop using all power equipment and consult a doctor if you feel tingling numbness or pain in the fingers hands wrists or arms The sooner RSI CTS is diagnosed the more likely permanent nerve and muscle damage can be prevented WARNING A DANGER Do not operate this product indoors or in inadequately ventilated areas Engine exhaust contains poisonous emissions and can cause serious injury or death Read the Manuals Provide all users of this equipment with the Operator s Manual and Safety Manual for instructions on Safe Operation Clear the Work Area e Spectators and fellow workers must be warned and children and animals prevented from coming nearer than 15 m 50 ft while the unit is in use Keep a Firm Grip e Hold the front and rear handles with both hands with thumbs and fingers tightly encircling the handles Keep a Solid Stance Maintain footing and balance at all times Do not stand on slippery uneven or unstable surfaces Do not work in odd positions or on ladders Do not over reach Avoid Hot Surfaces During operation the drive shaft housing attachment bearing housing and muffler cover area may become very hot too hot to touch Avoid contact during and immediately after operation
13. ver is shown within the circle is prohibited NOTE This enclosed message provides tips for use care and maintenance of the unit Symbol description application Symbol form shape EP NN Symbol form shape 557 Read and understand Fuel and oil mixture Operator s Manual Finger Severing VVear eyes ears and head protection i Avoidall power INS Do not operate lines This unitis mS closer than 15 M not insulated 50 ft from againstelectrical electrical current hazards Keep bystanders atleast 15 meters 50 feet away Wear hand protection Use two handed DO NOT smoke near fuel Planretreat path from falling objects PERSONAL CONDITION AND SAFETY EQUIPMENT DONOTallow flames or sparks near fuel Emergency stop Choke Control Cold Start Position Choke Closed Choke Control Run Position Choke Open Carburetor adjustment Low speed mixture WARNING A DANGER VVear slip resistant foot vvear Ignition ON OFF Primer bulb Carburetor adjustment High speed mixture Carburetor adjustment Idle speed Keep bystanders and helpers away 15 m 50 ft Trimmer Brush Cutter users risk injury to themselves and others if the trimmer brush cutter is used improperly or safety precautions are not followed Proper clothing and safety gear must be worn when operating a trimmer brush cutter 3 4 MECHO Physical Condition Your judgment and physical
14. zed warranty work will be done It also provides a direct link between you and ECHO if we find it necessary to contact you ADDITIONAL OR REPLACEMENT MANUALS Safety Manuals in English Spanish or English French are available free of charge from your ECHO dealer or at www echo usa com Operator s and Parts Manuals are available by e Downloading free from www echo usa com e Purchasing from your Echo Dealer e Manuals are available by sending a written request stating the model number and serial number of your Echo unit part number of the manual your name and address and mail to the address below Safety Videos are available from your Echo dealer A 5 00 shipping charge will be required for each video MECHO ECHO INCORPORATED 400 Oakwoop Roap LAKE ZURICH L 60047 www echo usa com 001001 999999
Download Pdf Manuals
Related Search