Dynex DX-24L150A11 Flat Panel Television User Manual
Contents
1. Move Select Next MENU Previous 3 Press A or W to highlight an option and press lt or P to change the setting Options include e Time Zone Select your time zone e DST If your area uses daylight savings time e Mode Select Manual to set date time manually or Auto to have them set automatically If you select Manual press A or W to highlight an option then press lt or gt to change the setting 4 When you are done press ENTER to move to the next screen The Choose your Picture Mode screen opens DYNE Setup Wizard Choose your Picture Mode wo O Retail Mode YOM Select Next MENU Previous 5 Press A or W to highlight Home Mode recommended or Retail Mode If you selected Home Mode the Choose your TV source screen opens gt a 4 lt Setup Wizard Choose your TV source Y RFCH 0 O Cable Digital Channels O Cable Satellite Box 0 Analog Channels Scan for channels b Move Select Next COT 6 Press A or F to highlight Antenna Cable or Cable Satellite Box then press If you selected Antenna or Cable your TV automatically scans for available channels If you selected Cable Satellite Box you are asked to select the correct input source for your set top box The channel scanning can take up to 30 minutes 7 Press EXIT to close the menu then select the input source through the INPUT SOURCE menu Selecting the video input source 1 Press INPUT press A or W to highlight a2. 47 D Y NE eee 24 LCD TV QUICK SETUP GUIDE DOL P Ne Front and side features Installing the stand 1 Remove the stand from the box and place it on a table or bench Note Pay close attention to the direction of the stand The wide portion of the stand must face the front of the TV 2 Lay the TV on a flat cushioned surface Align the stand with the TV as shown 4 Move the stand gently until the locators on the stand column align with the locating grooves on the stand w 5 Align the holes in the stand with the holes in the stand column 6 Secure the stand to the column with the three screws provided Screw holes nstalling a wall mount bracket 1 Carefully place your TV screen face down on a cushioned clean surface to protect the screen from damages and scratches 2 Remove the four screws holding the TV to its stand column then remove the stand column 3 Secure the wall mount bracket not included to the back of your TV using the screws provided with the bracket Setting up your remote control 1 While pressing the release button on the battery compartment cover on the back of the remote lift the cover off the remote 2 Insert two AAA batteries into the battery compartment Make sure that the and symbols on the batteries align with the and symbols in the battery compartment 3 Replace the cover To program your existing remote control to work with your Dynex
3. TV see the table below for common codes If you have problems programming your remote or need a different remote control code visit www dynexproducts com for the latest remote control code information Universal remote control TV codes for all Dynex TVs manufactured after Jan 1 2007 Universal remote control makers and models Set top box makers and models Philips One for All Sony Comcast Dish Network Motorola TVO Direct V A PHDVDS PHSDSS i i PMV PovRe PUSO URC 6690 RM VL600 M1057 VIP508 VIP622 DRC800 Series 3 HD R3 115 135 0464 8043 0463 720 0463 0091 10463 Connecting a DVD or Blu ray DVD player cable box satellite receiver or game station Using HDMI best Back of TV DIGITAL OUTPUT OUTPUT HDMI 1 1 DATA PORT RGB OUT HDMI OUT HDMI device HDMI cable not included Using component better Back of TV V P a CUR OMPONENT IN c SVIDEO VIDEO R L AUDIO R CATT Component video device Component video cable Using S video fair Back of TV Pe Pr L AUDIO R ANT CABLE IN COMPONENT IN SVIDEO VIDEO 1 AUDI0 R CRIE GR DUT Video device a S VIDEO S video cable VIDEO AUDIO VIDEO OUT Connecting an antenna Connect a 75 ohm cable not included to ANT CABLE IN jack on the back of your TV and the RF OU
4. source then press ENTER You can also press any of the video source buttons directly Adjusting the volume e Press VOL or VOL to change the volume e Press MUTE to turn off the sound Selecting a channel e To move to a different channel in the channel list press CHA or CHV OR Enter the channel number directly using the number buttons Press to change the volume Press to change the channel Viewing channel information e Press INFO to view an information banner The information banner shows the current program information such as channel number video input source and resolution e Digital mode information Displays the channel number station name channel label broadcast program name TV rating signal type audio information resolution CC mode current time and current program start and end times Analog mode information Displays channel number channel label if preset signal type audio information and resolution e Press GUIDE to show the digital program guide which may view a list of available programs program times and program summaries depending on the information provided by the broadcaster On screen menu overview Picture menu DY NE 7 Picture Mode Contrast Brightness Color Tint Sharpness Backlight Pate AYE Ta e e IAA Te 10 Audio OOR Gni AUDIO menu Sound Mode Bass Treble Balance Surround AVC Digital Output Audio Language SETU
5. P menu DY NE e Parental Controls Time Closed Caption Menu Settings VGA Settings Input Label Restore Default Audio Only Picture Audio Select CHANNEL menu TV Source Auto Scan Favorites Show Hide Channel No Channel Label Picture Audio Antenna 2 1 WGBH SD DTV Signal Select VvvvVvVvVVV VY Setup gt gt gt gt gt gt Normal Navigating menus with your remote control Press to open the O on screen menu Press to select menu options Press to return to the O previous menu MENU MENU A 49D IOD So EXIT Press to move the cursor on the screen or to adjust a selected item Press to confirm a selection or to enter a sub menu Press to close the menu LCD TV QUICK SETUP GUIDE I DX 24L150A11
6. T jack on the antenna Back of TV Y Pe Pa _L AUDIO R OMPONENT IN Cc SVIDEO VIDEO LsAuDio R L AUIO R OAND Antenna cable Using composite good Back of TV N Pa Pr L AUDIO R Fen COMPONENT IN SVIDEO VIDEO i C un Gam Video device VIDEO 2 Composite video cable AUDIO AUDIO VIDEO OUT Connecting a home theater system Using analog audio cable Y Pe e ADOR COMPONENT IN SVIDEO VIDEO a L AUDIO R GUO Back of TV Audio cable Note Cable connectors and jacks are often color coded Match the colors when you connect the AV cable Using digital audio cable Back of TV DIGITAL OUTPUT Note The DIGITAL OUTPUT jack only works with digital TV channels Connecting power Connect the power cable to the AC IN jack on the back of the TV then connect the other end to a power outlet Turning on your TV for the first time 1 Plugin your TV and turn it on The initial Setup Wizard opens DYNEX Choose your menu language Setup Wizard O Fran ais O Espa ol Move Select ENTER Next CUENU Previous 2 Press A or W to select the menu language you want then press ENTER The Time screen opens DYNEX Time DST lt oii gt Mode lt Auto gt lt lt lt lt Setup Wizard Year 2010 03 15 09 05 AM Month Day
Download Pdf Manuals
Related Search