Directed Electronics AS-1775 Remote Starter User Manual
Contents
1. 5 BUTTON AUTOMATIC MANUAL TRANSMISSION REMOTE STARTER amp AS 1775 User Guide WARNING It is the responsibility of the vehicle operator to ensure that their vehicle is parked in a safe and responsible manner 1 a Manual transmission When leaving the vehicle it is the user s responsibility to ensure that the gearshift lever is in the NEUTRAL position and the parking brake is engaged in order to avoid accidents upon remote starting b Automatic transmission When leaving the vehicle it is the user s responsibility to ensure that the gearshift lever is in Park in order to avoid accidents upon remote starting Note Make sure that the automatic vehicle cannot start in Drive 2 ltis the user s responsibility to ensure that the remote starter is disabled or put into valet mode before servicing Designed amp engineered in Canada Lixected ELECTRONICS CANADA INC INDUSTRY CANADA USER NOTICE Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power EIRP is not more than that required for successful communication NOTE The manufacturer is not responsible for any radio or TV interference2. If the system was installed with the starter kill option you will not be able to start the vehicle with the key unless the system has been unlocked first or put into Valet Mode Note If the Starter Kill is installed the vehicle will benefit from a protection against starter motor damage that could occur after remote starting the engine should the user by force of habit turn the ignition key to the CRANK position P 4 User Guide The Starter Kill if installed can be configured by the installer either to Passive Mode so as to arm automatically or Active Mode so as to require the user s intervention for arming By default your Remote Car Starter is configured to Passive Mode Passive mode To arm the Starter Kill press the button on the transmitter OR 1 n Passive Mode the Starter Kill will automatically arm 1 minute by default or 3 minutes if configured this way after the ignition is turned OFF or once the last door is closed if the doors are monitored 2 The LED on the antenna will flash quickly during the countdown preceding the activation of the Starter Kill 3 Once the activation countdown expires the LED will send a series of quick double flashes to indicate that the Starter Kill is now armed To disarm the Starter Kill press the kl button on the transmitter e The Starter Kill will automatically rearm itself after 1 minute by default or 3 minutes if configured this way if no door is left open
3. To stop the vehicle at any moment simply press the STOP button This procedure can only be carried out once per remote start Example f your Module is programmed for a runtime of 3 minutes and your vehicle has been running for 2 minutes already pressing the A button will reset the counter to zero and the Engine will run for another cycle in this case 3 minutes Disable Enable LED flashing To disable the LED Press and simultaneously until the parking lights flash three times To Enable the LED Press and simultaneously until the parking lights flash once Constant output e Pressing and holding the button for more than 3 seconds will lock all doors and will send a constant pulse as long as the SI button is held down maximum of 15 seconds This constant pulse can be configured to activate certain functionalities such as rolling up the windows Please refer to your installer to see if your vehicle is compatible with this option e Pressing and holding the button for more than 3 seconds will unlock all doors and will send a constant pulse as long as the E button is held down maximum of 15 seconds This constant pulse can be configured to activate certain functionalities such as rolling down the windows Please refer to your installer to see if your vehicle is compatible with this option User guide P 9 Advanced Features Installation programmable Options The Remote Car Starter was designed with flexibility and OEM in
4. set the system to Ready Mode If Ready Mode is enabled by remote If Ready Mode is enabled by handbrake 1 Ensure that all the doors hood and trunk are closed Make sure that the gear selector is in the neutral position 2 With the engine already running apply the 2 With the engine already running apply the parking brake once and release the brake parking brake twice within 10sec User guide P 5 Make sure to release the brake pedal The parking lights will flash 3 times quickly and remain lit Skip to step 4 Within 20 sec of engaging the parking brake press and hold m kl or H on the transmitter The parking lights will flash 3 times quickly and remain lit 4 Remove the key the engine will continue running 5 Exit the vehicle and close all doors hood and trunk 6 Press for approx 1 second either e io to lock the doors and shut down the engine e kio unlock the doors and shut down the engine to shut down the engine without affecting the doors 7 The parking lights will flash twice to confirm ready mode activation Remote starting Press the A button for approximately 1 second The parking lights will turn ON to inform you that the Remote Car Starter has received your signal Approximately 5 seconds later the engine will start The parking lights will remain oN during the pre programmed run time of the engine If your vehicle has an automatic transmission and it does not start at the first att
5. STARTER LOCK Locks the doors and arms KILL Activates the AUX 1 the STARTER KILL output if priority door access is configured TRUNK Opens the TRUNK or activates the AUX 3 output START Remote starts the engine or gets the system into Cold Weather mode if pressed for 3 seconds STOP Stops the engine if pressed Note On certain models the for less than 3 seconds or triggers START button will bear this Panic mode if pressed for more than 3 seconds icon N B Pressing the Lock and UNLOCK buttons simultaneously will activate the AUX 2 output Vehicle Presets Heater When leaving the vehicle it is recommended to preset the accessory controls in preparation for the next remote start Settings for the blower motor fan front and rear should not be left on HIGH It is recommended to leave the settings on LoW or MEDIUM instead Windshield Wipers Radio amp Headlights Certain vehicles require the radio and or windshield wipers and or headlights circuits to become energized while running under remote start When leaving the vehicle you must ensure that the windshield wipers and headlights switches are oFF Leaving the headlights switch ON on certain types of vehicles could cause them to remain ON even after remote starter shutdown resulting in a dead battery Arming and disarming the Starter Kill This added security feature will prevent the vehicle from starting with the Ignition key when the starter kill is armed
6. arm your factory security system and relock the doors Safe Start e Safe start enabled If this feature is enabled the user must press the H button twice within 3 seconds to remote start the vehicle This will eliminate accidental remote starts e g when children are playing with the transmitter e Swap start If this feature is enabled press JI and kl simultaneously to remote start the vehicle The AUX 2 output can be activated by pressing the E button Engine Run Time On a gas engine the Remote Car Starter can be programmed to run the engine for 3 15 or 25 minutes 15 minutes by default On a diesel engine the Remote Car Starter can be programmed to run the engine for 8 20 or 30 minutes 20 minutes by default Turbo Mode If Turbo Mode is configured at installation it will allow a turbocharger to idle down after the user leaves the vehicle the unit will take over the vehicle and keep it running for 60 seconds or until it is shut down by remote control then shut down the engine If your vehicle has an automatic transmission proceed as follows to set the system to Turbo Mode 1 With the engine running make sure to release the brake pedal and press the R or H button on the transmitter until the parking lights come ON 2 Remove the ignition key from the ignition switch The engine will continue running 3 Exit the vehicle and close all doors hood and trunk P 10 User Guide 4 Press the button this will
7. caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment Doc 100806 Rev 1 3 2010 AS 1775 FcN Canada Table of Contents Government regulations eerte treten ntenntenttnntnn ntes ttes trente tentes testes tes tnais 3 A Introduction iu i I DDR I T EDAM eae aaraa Aai EAA Pe SAA MM IM MEM SE NA aa 3 Using the Remote Control sssssssssssssssssssssssssssssssnsestsssseesssessssnssseseseseassssesteeaeseaseensssnssatseateatseneees 4 Vehicle Presets 4 az E T 4 Windshield Wipers Radio amp Headlight nnn 4 Arming and disarming the Starter Kill ssssssscssssssssseesseesssesesssessseesesssessneesssesesenteenesaneeneseneenteenees 4 Remote Starting Your Vehicle sssssssssssssssssssssessseesseessssssssessnsenssestssessteestssaeeeseeeneensseneseneeaneeneens 5 Setting Your Vehicle Into Ready Mode sss 5 Rerriotesstarting scitote te e oit tb sa DEREN 6 DIVING Off sso ire accen e rotos attt ino tre muri vis rim a tacto rag 6 Remote Starter secum 6 Remote Door LOCKS iani annainn ree ee ei tt e cde ce e aves 6 Remote Trunk Release os ERE ee ce RU UR EUER Uem 7 Idle Mode m et C UR em i eR Es 7 Malet MOOG tne dre i rd e e ec ER I C ERU ret 7 Panic Mode D 8 QUICK LOCKOUT IMs 2 i
8. d If the vehicle needs to be serviced or if you park it indoors the Valet Mode will prevent the engine from being remote started accidentally Any of the following features will put your remote car starter into Valet Mode Ignition Valet This feature allows you to put your system into Valet Mode by using the ignition key Remote valet This feature allows you to put your system into Valet Mode by using the transmitter To put the system intoValet Mode To put the system into Valet mode using the KEY Ignition Valet Mode 1 Insert the ignition key into the ignition switch Within 10 sec turn the key 5 times successively into the IGNITION RUN and OFF positions 2 The parking lights will flash three times 3 Turn the ignition OFF 4 The LED on the antenna will come ON solid to indicate that the vehicle has successfully entered Valet mode To put the system into Valet mode using the TRANSMITTER Remote Valet Mode User guide P 7 1 Press the KB and H buttons simultaneously until the parking lights flash three times 2 The LED on the antenna will come ON solid to indicate that the vehicle has successfully entered Valet mode To put the system out of Valet Mode To put the system out of Valet mode using the KEY Ignition Valet Mode 1 Insert the ignition key into the ignition switch Within 10 sec turn the key 5 times successively into the IGNITION RUN and OFF positions 2 The parking lights will flash twice 3 Turn the igniti
9. e running and the doors locked while you stop for example at a convenience store or for a short delivery This feature allows you to let the remote starter take over control of the vehicle i e no Key in the Ignition Switch while the engine is running If your vehicle has an automatic transmission proceed as follows to set the system to Idle Mode 1 With the engine running make sure to release the brake pedal and press the gi I or A button on the transmitter until the parking lights come ON 2 Remove the ignition key from the ignition switch The engine will continue running 3 Exit the vehicle and close all doors hood and trunk 4 Press the button to lock the doors to arm the starter kill and to arm the OEM style alarm If your vehicle has a manual transmission Idle Mode can be activated through the same routine as that used for Ready Mode page 5 at the last step press button to lock the doors arm the system and leave the engine running Note1 The engine will continue running until the user re enters the vehicle or until the expiration of the engine run time Note2 If the pre programmed run time expires or if the user shuts down the engine by remote control the vehicle will enter Ready Mode Caution Do not leave children or pets unattended in a vehicle standing in Idle Mode Valet Mode When the vehicle is in Valet Mode the remote starter and alarm functionalities are disable
10. e valet mode e Turnthe ignition key to the IGNITION ON RUN position The system will warn you if someone attempts to start your vehicle while it stands in home valet mode The parking lights will Turn ON then OFF then Flash twice pause then Flash twice again AUX1 Note This 500 mA negative Aux 1 output can be used for many different applications Priority door This great feature allows the user to unlock solely the driver s door with a single press of the KB button on the transmitter and to unlock the other doors if desired by pressing the kl button for a second time The output will provide a 1 second negative output when the button is pressed a second time on the transmitter Horn Confirmation AUX 1 can be programmed to trigger the horn every time the KI button is pressed or when the KH button is pressed twice within 3 seconds When horn confirmation is User guide P 11 activated panic mode is enabled If horn confirmation is disabled panic mode will not be available Horn Chirp Timing The pulse duration can be configured by your installer from 5 ms to 200 ms Multi car Operation This option allows the owner of two vehicles both equipped with the same Remote Car Starter model to control both systems with a single remote control To control the second vehicle simultaneously press the TRUNK button and the button of the function you wish to use Note Your remo
11. ed if the doors are monitored and the ignition is not turned ON Active Mode To arm the Starter Kill press the KG button on the transmitter 1 The parking lights will flash once 2 The LED on the antenna will flash slowly 3 f remote door locks are installed this will also lock the doors and arm the OEM style alarm To disarm the Starter Kill press the kl button on the transmitter 1 The parking lights will flash twice 2 The LED on the antenna will remain OFF 3 If remote door locks are installed this will also unlock the doors Remote Starting Your Vehicle Setting Your Vehicle Into Ready Mode If your vehicle has a manual transmission you must read the following indications The unit must first be set to Ready Mode in order to start the vehicle by remote If the unit is not set to Ready Mode it cannot remote start the vehicle Please note that Ready Mode can be enabled by the remote or the handbrake depending on the option that was selected by your installer Therefore you must follow the appropriate procedure between the two described below in order to set your vehicle into Ready Mode Once the system is set to Ready Mode the vehicle can be remote started and stopped at any time The system will exit Ready Mode if a door the hood or the trunk is opened if the brake pedal is pressed if the parking brake is disengaged or if the ignition key is turned to the IGNITION ON RUN position To
12. ehicles equipped with an aftermarket or factory alarm Parking Light Flash Table Parking lights flashes Description e Doors locked 1 e Trunk released e Start signal received from the remote e Runtime has expired 2 fast e Doors unlocked e Valet mode is deactivated 2 slow e Shutdown by remote e Shutdown by brake fies e A remote start was attempted while the brake pedal is engaged 3 slow e Runtime is extended 3 fast e Valet mode activated 10 fast e Shutdown by hood l e A remote start was attempted while the hood is open ON gt twice e Cold weather mode deactivated ON gt 3 times e Cold weather mode activated Solid ON e Engine is running under remote start Flash for 30 sec e Panic mode is triggered Flash for 60 sec e Alarm is triggered ON gt twice gt twice e A remote start was attempted while the system is in home valet User guide P 13
13. empt the system will shut down wait a few seconds and try to start the engine again There will be 3 start attempts before the system gives up Driving Off With the vehicle running under remote control press the kl button to disarm the Starter Kill and or the OEM style alarm if installed and unlock the doors Enter the vehicle and do the following e Turn the ignition key to the IGNITION ON RUN position Do not turn the key to the CRANK position while the engine is running This would cause the starter motor to re engage e Press the brake pedal to disengage the remote starter unit You are now ready to drive off Remote Starter Features Remote Door Locks If your system was installed with the Remote Door Locks option you will have the convenience of remote keyless entry To lock your doors and arm the starter kill if installed 1 Press and hold the JI button for approx 1 sec 2 The parking lights will flash once to confirm that the doors have been locked To unlock your doors and disarm the starter kill if installed 1 Press and hold the kl button for approx 1 sec 2 The parking lights will flash twice to confirm that the doors have been unlocked P 6 User Guide Remote Trunk Release If your system was installed with the Remote Trunk Release option you can open your trunk by pressing the HM button for 3 seconds on the remote transmitter Idle Mode Convenience feature Idle Mode allows you to keep the engin
14. lock the doors arm the OEM style alarm if configuredl and confirm that the vehicle is in Turbo Mode 5 The engine will shut down after 60 seconds If your vehicle has a manual transmission follow all steps of the Ready Mode routine page 5 to activate Turbo Mode At the last step press either Bio lock the doors and have the engine shut down after 60 seconds The parking lights will flash 3 times and remain lit The OEM style alarm and starter kill if configured will be armed a to unlock the doors and have the engine shut down after 60 seconds The parking lights will flash 3 times and remain lit to shut down the engine without affecting the doors Note The vehicle will enter Ready Mode once the engine run time expires Home Valet Mode If configured at installation this feature will remotely set the vehicle to a no remote start mode if the vehicle is parked indoors there is no danger of it starting accidentally by remote control If the vehicle has a manual transmission it should be set into ready mode before activating the Home Valet Note Once the Home Valet Mode is activated the vehicle will not start by remote but the OEM alarm functions will remain active To take the system into home valet mode 1 Press the M3 or button 2 Within 3 seconds press the Dana Hl buttons simultaneously for 3 sec 3 The P lights will flash once To take the system out of hom
15. ment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with the Industry Canada Radio Standards Specification RSS 210 Its use is authorized only on a no interference no protection basis in other words this device must not be used if it is determined that it causes harmful interferences to services authorized by IC In addition the user of this device must accept any radio interface that may be received even if this interference could affec
16. mode page 5 should be set before entering Cold Weather mode When Cold Weather Mode is active the engine starts every 2 hours and runs for 3 minutes or for 8 or 20 minutes with diesel engines Cold Weather Mode automatically ends after 24 hours or 12 starts To enter Cold Weather Mode e Press and hold the A button for at least 3 seconds e The parking lights will flash for 2 seconds pause then flash three 3 times To exit Cold Weather Mode do any one of the following actions e Openthe hood e Start the engine by remote P 8 User Guide e Tur the ignition key to the IGNITION ON RUN position e Press and hold the 4 button until the parking lights come ON for 2 seconds pause and then flash once If Safe Start is enabled you can activate Cold Weather Mode by e Pressing and releasing the A button then pressing and holding the A button until the parking lights flash 3 times To verify whether the system is in Cold Weather Mode automatic transmissions only e Press the brake pedal e f the vehicle is in cold weather mode the parking lights will remain ON while the brake pedal is pressed Extended Run Time With the vehicle running under a remote start pressing and holding the H button for more than 3 seconds will reset the run time counter to zero and restart the run time cycle from the beginning e The horn if programmed will honk once e The parking lights will flash slowly 3 times then remain lit
17. on OFF 4 The LED on the antenna will flash quickly to indicate that the vehicle is now out of Valet mode To put the system out of Valet mode using the TRANSMITTER Remote Valet Mode 1 Pressthe kl and Hl buttons simultaneously until the parking lights flash twice 2 The LED on the antenna will be OFF The system will warn you if someone attempts to remote start the vehicle while in Valet Mode The parking lights will Turn ON then OFF then Flash twice Panic Mode Note Panic mode can only be activated if the horn has been adequately configured by the installer In an emergency situation you can activate panic mode by pressing and holding the STOP button for more than 3 seconds until the horn starts honking If the vehicle is under a remote start the engine will shutdown automatically before setting off the horn You can stop the horn by pressing this will lock your doors and deactivate panic mode or kl this will unlock your doors and deactivate panic mode Furthermore the panic mode can be stopped by activating Valet Mode page 7 Panic Mode will automatically shut down after 30 sec Quick Lockout Also called Secure Panic For fast protection in emergency situations the system will LOCK all doors when you press the brake pedal while you hear the sound signal Quick Lockout is only available when panic mode has been set off Cold Weather Mode If the vehicle has a manual transmission Ready
18. rte merit recorre tet recae taedis hd rente GTI 8 Cold Weather Mode ctr ge nina E EEEE 8 Extended Bub Time nord ri EE HER Et d 9 Disable Enable LED flashing sse tentent 9 Gonstant oulput 5o e ERREUR RU I ed a 9 Advanced Features Installation programmable Options nene 10 Ignition controlled Door EOCKS 5 2 21 rtr tico tectam tcn 10 SEGUE LOCK 2 02 06 8 Ook hak na MIS Ln ELM E 10 Safe Start ce et er e e Are teet 10 Engine Run Titriez Je ERREUR RU RU RUE RI ER dg 10 Turbo Mode reete eer ei ee HIE nU RR RA edd ante 10 Home ValetM Mode toe i eo eee menm acinar 11 AUX Vek ict rr terti irent E e ER ioter t en dece pet ted 11 Horn Chirp TIMING ste cite ero eiit ht ah o tra iran 12 Multi Car Operation rte rece re RR ER AERE engen 12 OEM Style Alarm edm s Intrusion Codes via ioi 3 o o ER n a 12 Troubleshooting Poor Transmitting Range eene ntentnntnnnnns 13 Parking Light Flash Table eere tnnt ttertententnntnn ttn tte tenentes tentes tes treni 13 P 2 User Guide Government regulations This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equip
19. t the operation of the device Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device Introduction C This is a state of the art remote car starter system The system is packed with advanced features such as priority access to the driver s door commodity features the Safe Start children safety feature and SmartStart SmartStart is a groundbreaking technology that enables your remote starter features to be accessed by your smartphone Features include keyless entry trunk release panic remote start stop toggle and alarm notifications Note SmartStart must be professionally installed For more information see your nearest authorised Directed Canada dealer With many advanced functions this product will satisfy any one of your expectations from high end commodity and security systems without neglecting any standard feature commonly offered by entry level starters Certain conditions apply See your authorised Directed Canada dealer User guide P 3 Using the Remote Control Your Remote Car Starter is equipped with a 5 button multi channel remote control It can operate two independent vehicles equipped with a Remote Car Starter see Multi Car Operation page 12 for second car transmitter functions The functions of the transmitter are as follows Picture serves as example only UNLOCK Unlocks the doors and disarms the
20. te control must be configured for second car operation by the installer Press TRUNK LOCK buttons simultaneously LOCK Press TRUNK UNLOCK simultaneously UNLOCK Press TRUNK START simultaneously START Press TRUNK STOP simultaneously STOP Press TRUNK START simultaneously for 3 sec Cold Weather Mode OEM Style Alarm The OEM style alarm if configured by your installer monitors the doors hood and ignition switch of your vehicle It will sound the horn if a door or the hood is opened or if the key is turned in the ignition 6 2 e Toarm the OEM style alarm press the JI button on the transmitter The OEM style alarm will ONLY arm if the button on the transmitter is pressed The LED on the antenna will flash slowly to indicate that the OEM style alarm is now armed e Todisarm the OEM style alarm press the kl button on the transmitter To stop the horn from sounding if the OEM style alarm is triggered press the or kil button or put the system in and out of Valet Mode Car Finder If configured by your installer the Car Finder option will help you locate the vehicle by sending a pulsating signal through the horn To hear the signal press and hold the or KB button This will produce a pulsating signal for the time you keep the button pressed Intrusion Codes via horn The system monitors the following e Doors e Hood e Ignition Note If an in
21. tegration in mind With its programmable options this unit can single handedly control nearly any electrical system in your vehicle Caution The programming of your system should be left to a professional Changing any one of the settings may affect the operation of your Remote Car Starter Please note that the following programmable options may require additional parts and labor Ignition controlled Door Locks This is an added security feature If your Remote Car Starter was installed with the lgnition Controlled Door Locks option the doors will automatically be locked as soon as the ignition key is turned to the IGNITION ON RUN position while the brakes are pressed The remote car starter will also lock any door that was unlocked and opened then closed the next time the break pedal is pressed When the key is turned to the orr position the doors will automatically be unlocked Secure Lock Disabled by default Before your vehicle can be remote started the factory security system must first be disarmed The Secure Lock feature may be required on certain vehicle models with factory security systems that automatically unlock the doors when the security system is disarmed To keep your vehicle protected when the factory security system is disarmed for a remote start Secure Lock will relock your doors as soon as the vehicle is started Once the engine is shut down by remote or after its runtime has expired Secure Lock will also re
22. trusion has occurred the HORN will sound for a maximum of 1minute If an intrusion has occurred and kl pressed the horn provides an intrusion code corresponding to the type of intrusion that occurred 1x power interruption 4 x Doors intrusion 3x Hood 6x Ignition P 12 User Guide Troubleshooting Poor Transmitting Range Many factors may affect the operating range of the transmitter Some of these are e The condition of the battery in the transmitter e The operating environment for example downtown radio frequency noise airports cellular phone towers e Metal any type of metal will affect operating range This includes the vehicle itself e The shape of the vehicle can affect range as well vans in general have less range e The shape of the roof and A pillars brings about considerable radio frequency deflection in this case the signal from the remote control As a result the direction in which the vehicle is facing in relation to the remote control can affect the range Straight on standing in front of the vehicle generally gives you the greatest range the second best performance is from the back Using the remote control from either side of the vehicle will usually give the lowest range e The range will be significantly lower in a crowded parking lot than in open space e Always hold the transmitter high approximately at shoulder height e The operating range will be somewhat lower on v
Download Pdf Manuals
Related Search