Directed Electronics 120XV Automobile Alarm User Manual
Contents
1. Page Recognition Acknowledgement To clear a page alert notification quickly press any button on the remote control This can be performed at any time during or after the page notification has occurred The remote control will not send a command to the system at this time it will only clear future repeats of the page notification The next time a button is pressed on the remote control it will send a command to the system 2004 directed electronics inc out of range notification If a command is issued from the remote but the remote is beyond the range of the vehicle to receive the command the remote responds with 2 sets of 3 quick beeps and the Green LED will flash 6 times To enter programming mode Press and hold all four remote control buttons simultaneously until one long beep is heard Programming mode is now entered Beeps On Off Press to select beeps On Off One beep is notification beeps On Two beeps is notification beeps Off The notification beeps are programmed On from the factory and can be programmed Off if they are not desired When programmed Off the remote will only flash the LEDs as notification of a command page or an alarm page Remote battery low notification Rv ae l Press to select low battery notification On Off One beep is low battery notification On Two beeps is low battery notification Off The Low battery Beeps are programmed On from the factory and can be programmed Off if they are2. For a period of five calendar year from the date of purchase of this auto security device Directed Electronics Inc promises to the ORIGINAL PURCHASER to repair or replace with a comparable reconditioned model free of cost any electronic control module which proves to be defective in workmanship or material under normal use SO LONG AS THE SYSTEM WAS SOLD INSTALLED AND SERVICED BY A PROFESSIONAL AUTO INSTALLER AND REMAINS IN THE CAR IN WHICH THE SYS TEM WAS ORIGINALLY INSTALLED If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the following page After the first calendar year from the date of purchase of this auto security device Directed Electronics Inc promises to the ORIGINAL PURCHASER to repair or replace with a comparable reconditioned model any electronic control mod ule which proves to be defective in workmanship or material under normal use FOR A CHARGE OF 45 00 SO LONG AS THE SYSTEM WAS SOLD INSTALLED AND SERVICED BY A PROFESSIONAL AUTO INSTALLER AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the following page This warranty contains the entire agreement relating to warranty and supersedes all previous and contemporaneous representations or understandings whether written or oral IN ANY EVENT DEI
3. pressing and will immediately activate this output to control an additional conve nience option The remote will respond with a page notification consisting of an out put tone once and the Yellow LED will flash 3 times This occurs at the remote after the system has received the command to activate any of the Auxiliary outputs 2004 directed electronics inc j The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it It detects any faulty switches and sensors and prevents them from disabling the entire system The microprocessor will also record and report any triggers that occurred during your absence Refer to the System Status Chirps and Table of Zones charts for diagnostic informa tion arming diagnostics If the security system is armed at the same time that an input is active such as a door opening or sensor triggering you will hear one siren chirp to indicate arming and a second siren chirp to indicate Bypass Notification A Bypass Notification chirp means that the security system ignores the input that was active when the system was armed until that input ceases Three seconds after that input ceases the security system will resume normal monitoring For example if your vehicle has an interior light exit delay and you arm your security system before the interior light turns off you may hear a second Bypass Notification chirp Once
4. AND OR ANY AND ALL WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND OR ANY AND ALL WARRANTY OF NON INFRINGEMENT OF PATENTS IN THE UNITED STATES OF AMERICA AND OR ABROAD NEITHER THE MANUFACTURER OR ANY ENTI TIES CONNECTED THEREWITH SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAM AGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAM AGES INCIDENTAL DAMAGES TOWING REPAIR REPLACEMENT DAMAGES FOR LOSS OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECONOMIC OPPORTUNI TY AND THE LIKE NOTWITHSTANDING THE ABOVE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state Make sure you have all of the following information from your dealer A clear copy of the sales receipt showing the following Date of purchase Your full name and address Authorized dealer s company name and address Type of alarm installed Year make model and color of the automobile Automobile license number Vehicle identification number All security options installed on automobile Installation receipts il 2004 directed electronics inc table of contents limited LL45 consumer warranty ccccccccccccccccvscsc
5. IS NOT LIABLE FOR THE THEFT OF THE VEHI CLE AND OR ITS CONTENTS This warranty is void if the product has been damaged by accident unreasonable use neglect improper service or other causes not arising out of defects in mate rials or construction This warranty is nontransferable and does not apply to any unit that has been modified or used in a manner contrary to its intended purpose and does not cover batteries The unit in question must be returned to the man ufacturer postage prepaid This warranty does not cover labor costs for the removal diagnosis troubleshooting or reinstallation of the unit For service on an out of warranty product a flat rate fee by model is charged Contact your autho rized dealer to obtain the service charge for your unit These systems are a deterrent against possible theft Directed Electronics Inc is not offering a guarantee or insuring against the theft of the automobile or its contents and disclaims any liability for the theft of the vehicle and or its con tents Directed Electronics does not authorize any person to create for it any other obligation or liability in connection with this security system 2004 directed electronics inc i TO THE MAXIMUM EXTENT ALLOWED BY LAW ANY AND ALL WARRANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COMMERCE THEREWITH THIS EXCLUSION INCLUDES BUT IS NOT LIM ITED TO THE EXCLUSION OF ANY AND ALL WARRANTY OF MERCHANTABILITY
6. automatically the next time you or anyone drives the vehicle This helps to protect the vehicle if someone takes your keys and 2 way remote by force in a parking lot 2004 directed electronics inc 31 NOTE If the VRS system is armed while operating the vehicle and not disarmed prior to leaving the vehicle it is still armed and will trigger the next time the vehicle is driven S vrs triggered sequence 32 Fifteen seconds after the last door has closed the in vehicle LED will begin flashing This delay is intended to allow you time to distance yourself from your vehicle in the event of a carjacking Forty five seconds later the siren begins chirping and the park ing lights begin flashing This time could be used to notify authorities that your vehicle has been hijacked and tell them what the VRS will do next Fifteen seconds after the siren chirps begin the siren s output will change to a continuous blast From this point on when the ignition key is turned off the VRS will immediately turn on the starter kill This will prevent the vehicle from being restarted thus immobilizing it at that spot Three minutes after the constant siren output begins the flashing parking lights and the siren will stop The starter kill will remain active until the system is disarmed If the door is opened or the ignition is turned off and on in an attempt to restart the car the siren and light flashing will be
7. electronics inc multi level security arming Multi Level Security Arming allows you to select which of the system s inputs or sensors will be active and which will be bypassed when the system is armed See Table of Zones section of this guide Pressing only in Standard Configuration again within five seconds of arming the system will activate the Multi Level Security feature Each time is pressed again a different security level is selected The different security levels are selected as follows gt Press once The siren chirps once The system is armed gt Press a second time within five seconds The siren chirps twice followed by a long chirp Zone 2 is now bypassed gt Press A a third time within five seconds The siren chirps three times followed by a long chirp Zone 4 is now bypassed gt Press A a fourth time within five seconds The siren chirps four times followed by a long chirp Zones 2 and 4 are now bypassed gt Press a fifth time within five seconds The siren chirps five times followed by a long chirp All input zones except the igni tion are now bypassed NOTE Multi Level Security Arming only applies to a single arm ing cycle Once the system is disarmed and then re armed all the zones will be active again After each press of the LC to reach the next level of security the remote will emit normal arm notification 1 beep and 3 flashes of the Orange LED For easie
8. electronics inc the in vehicle s status LED is flashing in groups see the Diagnostics Section of this guide This extra chirp is called Bypass Notification The remote responds to active arming with one beep and the Orange LED will flash 3 times to indicate successful arming of the system If after 2 seconds the remote beeps once and the Orange and Red LEDs flash 3 times the system has detected an active sensor that should be checked If after 2 seconds the remote beeps once the Orange LED flashes 6 times and the Red LED lights for 3 seconds the system has detected an open door hood or trunk and has been bypassed passive arming The system can be programmed to arm itself automatically called pas sive arming If the system is programmed for passive arming it will auto matically arm 30 seconds after the ignition is turned off and the system detects that you have left the vehicle by opening and closing a door Whenever the system is in its 30 second passive arming countdown the in vehicle status LED will flash twice as fast as it does when the system is armed At the 20 second point of the countdown the siren will chirp to indicate that the system is about to arm At the 30 second point the parking lights will flash to indicate that the system is armed The remote responds to passive arming with one beep and the Orange LED will flash 3 times to indicate successful arming of the system 2004 directed electronics
9. functions door locks trunk release etc will continue to work normally To enter or exit Valet Mode 1 Turn the ignition on OFF Ta S S Z 2 Turn the ignition off 3 Press and release the Valet button once within 10 seconds The in vehicle status LED will light solidly if you are entering Valet Mode and it will go out if you are exiting Valet Mode The remote will respond with 3 Orange LED flashes on entering and 2 beeps and 3 Orange LED flashes on exiting Valet Mode 2004 directed electronics inc To enter or exit Valet Mode using the 2 way remote 1 Open any vehicle door 2 Press 8 3 Press Eyl 4 Press again The in vehicle status LED will light solidly if you are entering Valet Mode and it will go out if you are exiting Valet Mode The remote responds with the normal arm disarm notifications with each remote button press nuisance prevention circuitry Your system has Directed s Nuisance Prevention Circuitry NBC It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder jackhammers airport noise etc Example If the alarm triggers three times within a 60 minute period and each time the same sensor or switch triggers the alarm NPC will interpret those triggers as false alarms After the third trigger NPC ignores or by passes that sensor or switch along with any other sensors or swit
10. inc 11 12 NOTE If any protected entry point such as a door or a switch protected trunk or hood is open the system will not passively arm unless forced passive arming is programmed on See Programming Options section Additionally each time a sensor is triggered during the arming countdown the 30 second count down starts over When armed your vehicle is protected as follows gt Light impacts trigger the Warn Away signal When triggered the siren chirps and the parking lights flash for a few seconds Heavy impacts trip a Triggered Sequence The sequence consists of the siren sounding continuously and the parking lights flashing for a pre programmed period which can range in duration from 1 to 180 seconds If a door is opened the system will immediately start chirping the siren and flashing the parking lights Three seconds later the siren output changes to a continuous blast This progressive response gives you time to disarm the system with your 2 way remote if you inadvertently open the door while the system is armed while still providing instant response even if the door is immediately closed Turning on the ignition key will trip the same progressive response as opening a door The optional starter kill prevents the vehicle s starter from cranking Any full trigger of the alarm system will immediately send an alarm page to your remote informing you that your vehicle should be checked 2004 directed
11. is lost and then reconnected the system will recall the stored state from memory This means if the unit is in Valet Mode and the battery is disconnected for any reason such as servicing the car when the battery is reconnected the unit will still be in Valet Mode This applies to all states of the system including arm disarm VRS and Valet Mode 2004 directed electronics inc 25 power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet Mode after a period of time in which no operation has been performed This lowers the current draw to the vehicle s battery Power Saver Mode takes over under the following conditions gt Power Saver when the system is armed After the system has been armed for 24 hours the in vehicle LED will flash at half its normal rate decreasing the system s current draw gt Power Saver in Valet Mode When the system enters Valet Mode the in vehicle LED illuminates steadily If the vehicle is not used ignition is not turned on for a period of one hour while the system is in Valet Mode the LED will shut off If the system remains in Valet Mode the LED will come back on the next time the ignition is turned on and then back off 26 Programming options control what your system does during normal op eration and require few or no additional parts However some may require additional installation labor The following is a list
12. less than one second before arming or disarming and the confirmation chirp s will be eliminated for that one operation only If you want the arm disarm chirps turned off permanently your dealer can do this for you NOTE The Warn Away response to lighter impacts is bypassed if the system is armed using Silent Mode This ensures that no chirps will be emitted by the siren in an area you want chirp free The sys tem is still fully capable of triggering Only the Warn Away response is bypassed The remote responds with the normal arm disarm notifications in silent mode If the remote has beeps programmed On the remote will beep 2004 directed electronics inc 17 panic mode If you are threatened in or near your vehicle you can attract attention by triggering the system with your 2 way remote Just press for two seconds and you will enter Panic Mode The siren will sound and the parking lights will flash for the programmed siren duration To stop Panic Mode at any time press on the 2 way remote again The remote responds with one flash of the Red LED upon entering Panic Mode and two flashes of the Red LED upon exiting Panic Mode valet mode 18 You can prevent your security system from automatically arming and triggering by using Valet Mode This is very useful when washing the vehicle or having it serviced In Valet Mode the security system will not arm even with the 2 way remote but all convenience
13. the light turns off however the secu rity system resumes normal monitoring disarming diagnostics Extra disarm chirps are the Tamper Alert If four chirps are heard when disarming the system was triggered in your absence If five chirps are heard a zone was triggered so many times that Nuisance Prevention 2004 directed electronics inc 21 Circuitry has bypassed that zone The in vehicle status LED will indicate which zone was involved See Table of Zones section of this guide The system will retain this information in its memory and continue to chirp four or five times each time it is disarmed until the next time the igni tion key is turned on system status chirps The siren will chirp when arming disarming the system The pattern of chirps will audibly report the system s status as described below Action Arm Arm Disarm Disarm Disarm Number of Chirps 1 1 3 second delay 1 table of zones The zone number is the number of in vehicle LED flashes used by the Description System armed System armed with Bypass Notification System disarmed System disarmed with Tamper Alert System disarmed NPC active system to identify that input The standard input assignments are listed below along with spaces to write in any optional sensors or switches you have had installed 22 2004 directed electronics inc Zone Number Dealer I nstalled of LED Flashes Description Opt
14. times out of range of the vehicle or if the battery has been removed it may get out of sync with the control unit and fail to operate the system To re sync the 2 way remote simply press of the 2 way remote several times within range of the vehicle The alarm will automatically re sync and respond to the 2 way remotes normally high frequency 24 Your system transmits and receives at 434 MHz This provides a cleaner spectrum with less interference and a more stable signal Enjoy a phe nomenal increase in range even in areas with high radio interference 2004 directed electronics inc u Owner Recognition is a feature available exclusively from Directed Using the Directed Bitwriter a hand held programming tool your dealer can program many of the system settings The programmer makes it possible to program different settings for each 2 way remote that is used with the system Then whenever a specific 2 way remote is used the system will recall the settings assigned to that 2 way remote Owner Recognition lets up to four users of the system have different settings that meet their specific needs It is almost like having four separate alarms in your vehicle one for each user NOTE Owner Recognition cannot be programmed without a Directed Bitwriter and the necessary software Check with your dealer for more information J ogi This Directed system will store its current state to non volatile memory If power
15. 2004 directed electronics inc Starter Kill and the VRS feature to provide the best combination of personal safety and property protection available When properly installed the system can never inadvertently stop your vehicle in traffic or on railroad tracks while the vehicle is in operation It is unlike other systems that shut down your engine while it is running This sys tem is designed to perform starter interrupt or starter kill The Failsafe Starter Kill cannot shut down an already running engine it can only prevent an engine from starting in the first place important Any installation that allows this product to shut down a vehicle s engine when it is running is contrary to the product s design and intended usage and Directed hereby expressly dis claims any liability resulting therefrom arming the vrs To arm the VRS turn the ignition to the ON position and press the arm button on the 2 way remote for one second The parking lights will flash and the siren will chirp once This can be done before driving or while driving the vehicle Once the system is armed it will initiate its trig gered sequence see below if any door is opened and closed If you are forced from the vehicle the system will trigger as the door is opened and closed This is how the system works to combat intersection carjacking To protect against parking lot carjacking arm the VRS before leaving the vehicle The system will now trigger
16. 436 Series Tested to Comply C with FCC Standards 2004 directed electronics inc 5 2 way remote control functions _ The 2 way remote control buttons are used to send commands to the system The descriptions below reflect the standard configuration for this system The buttons can be custom configured for the user s specific needs by the installer standard button configurations Button The System Arm and Multi Level Security Arming functions are controlled by pressing this button for one second Button The System Disarm and High Security Disarm functions are controlled by pressing this button for one second Button Silent Mode and an optional auxiliary function are controlled by this button Silent Mode works by pressing this button for less than one second before arming or disarming An optional auxiliary function such as trunk release can be controlled by pressing this button for 1 5 seconds The auxiliary output controls Button The panic feature is controlled by pressing this button for 2 seconds 6 2004 directed electronics inc A and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simul taneously The auxiliary output controls The remote start system operates at 434 MHz and incorporates Directed s proprietary XHF2 out board technology transceiver The high frequency combi
17. Boeke cai ca saree eign gh a avid iO Did Did Did NO a GUAM eee eer 18 nuisance prevention circuitry 636444 S44 Oa PRR ERR RER 19 auxiliary outputs options x x x lt x 6 69 0 6 69 6 eee as 20 diagnostiseren oeiee eas aT a a alala a alee sles SNARE RERE ENERE 21 arming GIAGNOSUICS ei eiir BARRE RRR EEE EER ALE 9 21 disarming diagnostics se cite apc desieedeg peed dp Pa te tee oe ee ee ee 21 system Status CHIPS TTT 22 POOLE of ZONES i S cats EEE hie EERE EE RG E 22 interpreting zone diagnostics neesan neern 23 code hoppihge e serere r eneren NNN NNN e es 24 high fregu en LTTE 24 owner recognition s sssssesssosessoooesosessoooeesoooeo 25 rapid resume logice seee es e urere aT anean a aT Taala ATT TTT a 25 power saver mode 22266453 N ER EMRE NR R ui nea 26 programming OPTIONS 5 5 lt lt lt lt ovsasassessass oS SSSR SSR SUES SS Ss 26 installation options lt lt lt lt lt e ese ww Ce BREAN OER ER Rs 30 vehicle recovery system VS ss e x e e eee ee 30 arming CHE WIS sunore oiidid i h Aah E OE EER EEEE h 31 vrs triggered sequence es nenna 32 disarming NEVIS 35 534 we RARA ER hee ERERECRERE CEES RN 33 glossary OF terMSz s oe R RC K ae SS FWA A WN OO ee 34 security amp convenience EXPANSIONS lt lt lt lt lt eee 36 QUICK feference gulde esere 83 6454563 85 555 8 HESS 39 2004 directed electronics inc 1 OO Arm Disarm Indicator Orange Rec
18. been pro grammed on the system will passively arm after one hour even if a protected entry has been left open This feature is useful if a door has been left ajar when leaving the vehicle Forced passive arming ensures that the security system will be armed in every situation 2004 directed electronics inc 27 NOTE When the system passively arms after one hour the entry point that has been left open and anything connected to the same zone is bypassed and cannot trigger the system However the remaining inputs to the system are fully operational Automatic Engine Disable AED on or off The purpose of this fea ture is to protect the vehicle from being stolen at all times regard less of whether or not the alarm is armed If AED is programmed on the starter of the vehicle will be disabled 30 seconds after the ignition is turned off Once the key is turned off the in vehicle LED will flash slowly one half its normal armed rate to indicate the AED arming cycle Thirty seconds later the starter of the vehicle will be disabled To start the car it will be necessary to disarm the system with the 2 way remote It is also possible to disarm the AED feature by turning the ignition key to the RUN position and pressing the Valet button the programmed number of times AED is disabled when the system is in Valet Mode NOTE This feature will only function if the Failsafe Starter Kill relay has been installed gt Full
19. ches sharing the same zone for 60 minutes If the bypassed sensor tries to trigger the system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that continually triggers will remain bypassed Doors are covered by NPC differently if the alarm is triggered by an open door for three full cycles the doors will be bypassed until the trigger ceases 2004 directed electronics inc 19 20 NOTE Arming and disarming the system does not reset this func tion The only ways to reset a bypassed zone are for it to not trig ger for 60 minutes or to turn on the ignition If testing your sys tem it is important to remember that the NPC programming Can cause zones to be bypassed and appear to stop working If five chirps are heard when disarming NPC has been engaged If you wish to clear the NPC memory turn the ignition key on NPC is programmable See Programming Options section of this guide This system also supplies outputs that can control convenience options such as remote control trunk release and window automation Consult your dealer for available options for your system Channel 2 Trunk release When connected pressing for 1 5 seconds will remotely release the vehicle trunk lid Channel 4 auxiliary output When connected pressing and will immediately activate this output to control an additional conve nience option Channel 5 auxiliary output When connected
20. eces i 2 way remote control diagram lt sss s cece cc cc ccc eee 2 standard remote configurations ccccccccccsccccvccscecces 2 what IS included 6 5 oes Od Wee eae eee EERE RRR RR ROS 3 important information lt lt lt lt lt lt s s e eee eee eee 3 system maintenance AR AOS Se SORES SSAA Saga nenene 4 VOUT WONLANIY 7 aa aaa d adad se ATTAR TRER REAT aw aac 4 ECG NOME s teres aie eee ee eee Geese cece ue eens ene k ees 5 2 way remote control functions lt lt ss s ccc e e eee eee 6 Standard button configurations os 6233 3e en be Ree eaten 6 remote perati n d Ra eR SERRE RRR RRR RRR RR Vee eee ee ee NN N N 7 system signal paging features SEs EEE EEE EES Ew OS 7 OUE Of TONGE TOGIICOUION 6 s VO bokeh hhh hhh bg hee a na eee eae 9 programming 2 way remote cecceccccccccsccecsscssecees 9 USING your System og 3 oe RARE RARASREWA RARER RRR 10 active ArMING ee aes te teat ee A BEDE E EERE ELEE ERS 10 passive arming e hee RRs he 898 8994 988 8 8 RE TEESE E ESS 11 multi level security arming Wise amp He ee GO 13 arming while driving 4 0548 GAO ge ee eR RR RS OR REA 14 disam eese t L GG a Ha AAA AAAAARARA ORE EEEEEEEEEELE OES 14 high security disg cdoed ch cick ch ok ca hc ch oh ch Choe es he See eee Wee HR RE 15 disarming without a 2 way remote iow 5 HOSED SHOR 16 Sent OUR See iat Rie eat dS hd dk at eee es 17 panic HOS lt aR eoio EaR RE RARER EEE EE EINER ERAS 18 valet TDC ine
21. eive Transmit Indicator Green sl NI atop slwl ros Auxiliary Indicator Yellow Siren Indicator Red Arm Button Disarm Button Panic Button Auxiliary Channel Button 2004 directed electronics inc ab i dead gt One control module gt An XHF2 transceiver antenna gt One 4 button 2 way remote gt Stinger Doubleguard dual stage shock sensor gt Revenger Soft Chirp six tone programmable siren gt In vehicle status LED indicator light gt Push button Valet switch Your warranty registration gt Failsafe Starter Kill ready circuitry may require additional labor Congratulations on the purchase of your state of the art vehicle security system This system has been designed to provide years of trouble free op eration Due to the complexity of this system it must be installed by an authorized dealer only Installation of this product by anyone other than an authorized dealer voids the warranty All dealers are provided with preprinted dealer certificates to verify that they are authorized This owner s guide should help you to get the most out of your system Please take the time to read it prior to using the system 2004 directed electronics inc 3 system maintenance This system needs no specific maintenance beyond 2 way remote control battery replacement The 2 way remote is powered by a 1 5V AAA battery Low Battery Notification If the battery is low and this feature is program
22. gin again 2004 directed electronics inc disarming the vrs Take the time to familiarize yourself with the RS triggering sequence and the disarm procedure It is important to recognize and identify the VRS trigger sequence and know how to disarm it in case of accidental activation Once the VRS is armed it does not disarm automatically You must disarm it the next time you operate the vehicle You must disarm it with one of the following procedures If the system has not entered the triggered sequence siren has not started chirping 1 Turn the ignition on OFF A No 2 2 Press Ey on the 2 way remote for one second The lights will flash and the siren will chirp twice If the system has entered the triggered sequence siren has begun chirping pressing the disarm button of the 2 way remote will not disarm VRS To disarm the RS during a VRS trigger sequence D 1 Turn the ignition on 5 o 2 N 2 Press the Valet button the pre programmed number A a we of times to disarm the VRS system 2004 directed electronics inc 33 NOTE If the VRS system has begun its chirping sequence the ignition must be turned off then on to disarm If you are driving the vehicle at the time pull to a safe place away from traffic and follow the triggered sequence disarm procedure glossary of terms 34 2 Way Remote Hand held 2 way transceiver which operates the va
23. h the triggered sequence Headlight and Parking Light Automation The 545T Nite Lite will automatically turn on your parking and headlights when it gets dark In addition the 545T will turn your headlights on whenever the windshield wipers are used A 2 way remote function can also be used to turn on your parking and headlights for a programmed time Power Trunk Release The channel two output of the system can operate a factory power release for the vehicle s trunk or hatch An additional relay may be required If the factory release is not power activated then Directed s 522T trunk release solenoid can often be added 2004 directed electronics inc Power Window Control Automatic power window control is provid ed with the 529T and 530T systems Mobile Video This system is compatible with Directed Video s MCB1000 Multi Channel Controller featuring on screen security system programming and zone trigger information Valet Start System For the ultimate in convenience the Valet start system can start your vehicle monitor engine functions and power your climate control system with a push of a button Over rev protection open hood lockout brake pedal shutoff and automatic timer shutoff are all included This feature is only for automatic trans mission fuel injected gasoline vehicles 543T XHFplus External Receiver Antenna The 543T XHFplus external receiverfantenna can be used to upgrade the transmitter rece
24. in a unique easily identifiable siren sound The siren chirps can be either full volume or six decibels quieter than the full alarm blast 2004 directed electronics inc 29 The system has many options that may require extra parts and labor Some of the possibilities are listed here gt Progressive unlocking In most cars with electric power door locks the system can be configured so that when the system is disarmed only the divers door unlocks A second press of the button unlocks the other doors gt Vehicle Recovery System VRS VRS is an anti carjacking device designed to help in the safe recovery of your vehicle in case of a carjacking Please refer to the Vehicle Recovery System section of this guide for a complete explanation of how the Vehicle Recovery System operates vehicle recovery system vra 30 The optional VRS feature is designed to ensure that any unauthorized user of your vehicle even if using your keys and 2 way remote will not be able to permanently separate you from your vehicle The VRS cannot prevent a carjacking attempt however it does ensure that if your vehicle is taken by an unauthorized user it will be disabled after several progressive warnings as safely as possible Should a carjacking occur the VRS allows you to concern yourself with your personal safety without worrying about your property Directed has engineered this vehicle security system the Failsafe
25. ing after the system has been triggered the remote control will send a diagnostic notification as a reminder These diagnostic notifications are 2004 directed electronics inc 1 Ifa sensor triggered the system the remote will beep 4 times and the Orange and Red LEDs flash 3 times 2 Ifa switch Zone 1 3 5 or 6 triggered the system the remote will beep 4 times the Orange LED will flash 6 times and Red LED will illuminate for 3 seconds 3 If the system was triggered so many times that NPC is active the remote will emit the above notifications with 5 beeps instead of 4 high security disarm This system includes High Security Disarm feature If the system is trig gered this feature allows the user to silence the siren and reset the system to the armed state without having to visually checking the system status After receiving an alarm page 1 First press any button on the remote to clear the alarm page 2 Press either the or button again and the High Security disarm feature will be activated The siren will be silenced and the system will reset to the armed state 3 Pressing the button once more will fully disarm the system and allow the vehicle to be accessed 2004 directed electronics inc 15 NOTES The first press of the remote button while the remote is beeping only clears the alarm page no command is sent to the vehicle The transceiver transmits immediately upon system trigger and does n
26. ions 1 Instant trigger often used for hood trunk pinswitches 2 A heavier impact detected by the shock sensor 3 Door switch trigger 4 For optional sensors 5 Ignition trigger interpreting zone diagnostics Warn Away responses are not reported by arming or disarming diag nostics If you receive a Bypass notification when arming or a Tamper Alert notification when disarming look at the in vehicle status LED Active or triggered zones will be indicated by a pattern of blinks by this LED Example If Zone 3 was active or triggered the in vehicle LED will blink three times with a two second pause Then it will blink three times again and repeat until the ignition is turned on NOTE Your system stores the last two triggered zones in mem ory If your system has been triggered but the LED has been reset by turning on the ignition your dealer can still recall the last two zones that were triggered Contact your dealer for details 2004 directed electronics inc 23 code hopping The receiver and 2 way remotes each use mathematical formulas called algorithms to change their codes each time the 2 way remote is used This technology has been developed to increase the security of the unit The control unit knows what the next codes should be This helps to keep the 2 way remote in sync with the control unit even if you use the 2 way remote out of range of the vehicle However if the 2 way remote has been pressed many
27. iver performance in areas of high radio interference such as military bases airports and hospitals 2004 directed electronics inc 37 Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet SREE o0 QUICK REFERENCE GUIDE To arm using your 2 way remote gt You can activate or arm the system by pressing on your remote for one second When the system arms you will hear a short siren sound or chirp and the parking lights will flash once If the vehicles power door locks have been connected to the system the doors will lock To disarm using your 2 way remote gt To disarm the system press Ey You will hear two chirps and the parking lights will flash twice If power locks are connected to the system the doors will unlock If the siren chirps either four or five times when disarming see Diagnostics section This is called Tamper Alert Arming while driving gt Dress j on your remote for two second while the vehicle is running The system will chirp once and then once more to indicate that the ignition is on Disarming without a 2 way remote gt Turn on the ignition Press and release the Vale button the programmed number of times within 15 seconds After five seconds the system will disarm If it does not you may have waited too long Turn the ignition off and on and try again To enter or exit Valet Mode gt Turn ignition to RUN position then turn to OFF positi
28. med On the 2 way remote will emit 2 long beeps 5 seconds after a transmission is completed The 2 long beeps will repeat every 25seconds up to 3 times or until a 2 way remote button is pressed Battery Replacement Gently pull the end of the battery door away from the top of the remote control then slide the door up to expose the battery and remove the expired battery Place the new battery into the remote control observing the correct polarity When power is returned the remote control will light all icons and generate melodies representing all beeper tones your warranty Your warranty registration must be returned and the bar code serial number must not be removed If the warranty registration is not returned you do not have a warranty It is also necessary to keep your proof of purchase which reflects that the product was installed by an authorized dealer Make sure that you receive the warranty registration from your dealer 4 2004 directed electronics inc fec id notice This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference re ceived including interference that may cause undesirable operation Changes or modifications not expressly approved by the party respon sible for compliance could void the user s authority to operate this device Directed Electronics Inc
29. ned with Binary Data communication achieves superior range with two way communication system signal paging features A page is the signal the control module sends to the remote control as confirmation of receipt of a command or alarm system status When the remote control receives a page it will generate a page notifica tion to the user notifications are audible beeps and the LED Icons will display the current system status Command Page When a command arm disarm or auxiliary channel from the remote control is sent and received the system will send a command page back to confirm receipt 2004 directed electronics inc 7 Alarm Page If the alarm system is triggered while armed an Alarm Page will be sent to the remote control When the remote receives an Alarm Page the LED icons will display the alarm system status information and the remote control will generate beeps An Alarm Page alert is a series of 10 or 4 rapid beeps and the Red LED will illuminate This will repeat every 100 seconds to alert the user that the alarm system was triggered and will continue until the alarm page is cleared If the shock sensor or optional sensor has triggered the alarm the remote will display the alarm page with 6 Red LED flashes and 10 rapid beeps If the trunk door ignition or hood triggered the alarm the remote will display the alarm page with the Red LED illuminating for 3 seconds and 4 rapid beeps repeated 5 times
30. not desired When programmed Off the remote will not give any notification that the battery charge level in the remote is low 2004 directed electronics inc 9 Page notification The remote control can be programmed to notify the user of a page audibly beeping if the vehicle s status changes e g door unlocked engine started vehicle violation etc Press to select page On Off One beep is page On Two beeps is page Off When programmed off the remote will not give any notification that a page was received from the vehicle To exit programming mode The remote control will exit programming mode after 2 seconds of inactivity and will emit 2 long beeps using your system The buttons used in the instructions in this manual correspond to the standard configuration Remember this is not the only way your 2 way remote may be set up It can be custom configured to meet your needs active arming 10 You can arm the system by pressing of your 2 way remote for one second When the system arms from the vehicle you will hear a short siren sound or chirp and see the parking lights flash once If the power door locks are controlled by the system the doors will also lock While the system is armed the in vehicle s status LED will flash approx imately once per second indicating that the system is actively protect ing your vehicle If you hear a second chirp after arming and note that 2004 directed
31. of the program settings with the factory settings in Bold 2004 directed electronics inc gt Active arming only with the 2 way remote or passive arming automatic arming 30 seconds after the last door has been closed gt Arming disarming confirmation siren chirps on or off gt The ignition controlled door lock feature on or off With this feature on the doors will lock three seconds after the ignition is turned on and unlock when the ignition is turned off The system will not lock the doors when the ignition is turned on with any door open If your installer is programming the security system with the Directed Bitwriter ignition lock and unlock are indepen dent features and can be programmed separately gt Passive door locking with passive arming or active door locking only when arming with the 2 way remote Passive locking allows the vehicle s doors to lock when the security system passively arms after the 30 second countdown This feature only works if passive arming has been programmed NOTE When programmed for passive arming and active lock if the system is disarmed without a door being opened the system will relock the doors when it passively rearms gt Panic mode enabled disabled with the ignition on Some states have laws against siren capability in a moving vehicle gt Forced passive arming on or off If your system is programmed for passive arming and the forced passive arming feature has
32. on Press and release the Valet button within 10 seconds The in vehicle status LED will light solid if you are entering Valet Mode and it will go out if you are exiting Valet Mode To activate Panic Mode gt Press and hold down for one second To exit Panic Mode gt Press L on the remote SS To activate Silent Mode gt Dress briefly before arming or disarming and the confirmation chirp s will be eliminated for that one operation only Location of Valet Button Number of Valet Button pulses for disarming 2004 directed electronics inc The company behind this system is Directed Electronics Inc Since its inception Directed has had one purpose to provide consumers with the finest vehicle security and car stereo products and accessories available The recipient of more than 20 patents in the field of advanced electronic technology Directed is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world Call 800 361 7271 for more information about our products and ser vices Directed is committed to delivering world class quality products and services that excite and delight our customers driven to excel Dxectca ELECTRONICS INC Directed Electronics Inc Delson Qc www directed ca 2004 Directed Electronics Inc All rights reserved G980120V 09 04
33. ot allow disarm during the first 6 seconds after trigger The 2 way remote will respond with a number of beeps and LED flashes according to whether a pinswitch sensor activated the alarm and also if NPC is active disarming without a 2 way remote This feature allows you to disarm the security system without the 2 way remote should it be lost damaged or disabled In order to disarm the system without a 2 way remote you must have the vehicle s ignition key and know where the Valet button is located Be sure to check with the installer for the location and the number of presses of the Valet button required to disarm the system To disarm the security system turn the ignition to the ON posi ars E Q tion Z 5 Press the Valet button the preset number of times one to five times within 15 seconds After five seconds the system will disarm If the system does not disarm you may have pawas waited too long turn the ignition Off and On and try again Location of Valet Button Number of Pulses 16 2004 directed electronics inc important The unit can be programmed to respond to one to five pulses of the Valet button for the disarm function Be sure to check with the installer for the desired programming The remote will indicate disarm notification with 2 beeps and 3 flashes of the Orange LED silent mode To temporarily turn off the arm or disarm chirps use Silent Mode Simply press for
34. rious functions of your system Control Unit The brain of your system Usually hidden under the dash area of the vehicle It houses the microprocessor which monitors your vehicle and controls all of the system s functions Fail Safe Starter Kill An automatic switch controlled by the security system which prevents the vehicle s starter from cranking whenever the system is armed The vehicle is never prevented from cranking when the system is disarmed in Valet mode or should the starter interrupt switch itself fail Your system is ready for this feature however installation may require additional labor Input A physical connection to the system An input can be provided by a sensor pinswitch or through an existing system in the vehicle such as ignition or courtesy lights In vehicle status LED A light mounted somewhere in the vehicle It is used to indicate the status of your system It is also used to report triggers and faults in the system or sensors 2004 directed electronics inc Shock Sensor This is a sensor mounted in the vehicle that is designed to pick up impacts to the vehicle or glass Siren Noise generating device usually installed in the engine com partment of the vehicle It is responsible for generating the chirps you hear as well as the six tones you hear while the alarm is triggered Trigger or Triggered Sequence This is what happens when the alarm goes off or trips The triggered re
35. sponse of your system consists of the siren sounding and parking light flashing for the programmed duration Valet Button A small push button switch mounted somewhere inside the vehicle It is used to override the alarm when a 2 way remote is lost or damaged or to enter or exit Valet mode Warn Away Response Lighter impacts to the vehicle will generate the Warning Zone response It consists of several seconds of siren chirps and parking light flashes Zone A zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone Two or more inputs often share the same zone 2004 directed electronics inc 35 36 Here we have listed only some of the many expansion options avail able Please contact your dealer for a complete explanation of all the options available to you Audio Sensor Metal on glass glass cracking and breaking glass each produce distinctive acoustic signatures The 506T audio sensor uses a microphone to pick up sounds and then analyzes them with proprietary acoustic software to determine if the glass has been struck Backup Battery The 520T keeps the system armed triggers the alarm and keeps the starter kill active if main battery power is disconnected Field Disturbance Sensor An invisible dome of coverage is estab lished by installing the 508D radar sensor Your security system can then react to any intrusions into this field wit
36. st operation in reaching each level of security press immediately after each notification 2004 directed electronics inc 13 arming while driving Your security system can be armed while driving the vehicle Simply press on the 2 way remote for two seconds while the vehicle is running The siren will chirp once to indicate that the security system is armed and then once more to indicate that the ignition is on The system will not respond to any input except the door triggers and the starter kill relay if installed will not be activated Once you have arrived at your destination the system can be disarmed by pressing the Ey or by turning the igni tion Off The siren will chirp twice and the in vehicle status LED will then stop flashing The system can also be disarmed at any time by pressing M mj The remote will respond with the normal arming response plus a diag nostic notification because the ignition On When disarmed the remote will respond with the normal disarming response disarming 14 To disarm the security system press Eyl You will hear two chirps and the parking lights will flash twice If the power locks are controlled by the system the doors will also unlock The siren chirping either four or five times when disarming indicates Tamper Alert which is described in the Diagnostics Section of this guide The remote will indicate disarm notification with 2 beeps and 3 flashes of the Orange LED If disarm
37. trigger response 30 or 60 seconds This determines how long the full triggered sequence lasts Some states have laws regulating how long a security system can sound before it is considered a nuisance If your installer is programming the security system with the Directed Bitwriter the full triggered response can be programmed for any duration ranging from 1 to 180 seconds gt Nuisance Prevention Circuitry on or off Please refer to the NPC 2004 directed electronics inc section of this manual for a complete explanation of how NPC oper ates If NPC is programmed off the security system will respond to inputs from any sensor indefinitely NOTE Because many states have laws regulating security sys tems programming NPC off may cause your system to violate state laws gt Progressive door trigger on or off When the system is armed and a door is opened the system responds with ten chirps prior to be ginning the full triggered sequence If an instant trigger is desired the progressive door trigger can be programmed off gt Maier pulse count The number of presses of the Valet button required to disarm the security system AED or the VRS system can be programmed from one to five presses The default setting is one press gt Siren tones and chirp volume The output of the Revenger Soft Chirp siren consists of six different tones in sequence Any of these tones can be eliminated by your dealer resulting
Download Pdf Manuals
Related Search