Dimplex ARLWP800TI Fan User Manual
Contents
1. Wall Mounted Operation see Fig 2 Suggested Fixings SOLID BRICK BLOCK No 8 Rawlplug inserts 6mm drill bit PLASTERBOARD lf possible locate studding and use No 8 woodscrews directly into the wood otherwise M5 rawlplug intersets are suitable NOTE FOR OTHER WALL TYPES e g Timber frame and hollow concrete SEEK SPECIALIST ADVICE 1 Select the position for the heater ensuring there is clearance from any furniture and fittings of at least 150mm above the heater 50mm below and 25mm each side Curtains must not be closer than 150mm from the top of theheater 2 Position the drilling template provided on the wall ensuring it is level Mark the position of the relevant holes on the wall at the edge of template Before drilling check that the distance between the hole centres is correct 340mm for 400W Models and 540mm for 800W models see Fig 2 150mm 130mm as 340mm 400W 130mm j 540mm 800W i Bracket 25mm Drilling Holes 50mm Fig 2 3 Drill the wall at the three marked positions and fit the wall plugs Ensure template has been removed 4 Fix two No 8 screws to the top two holes leaving 3mm of the screw exposed Hang the heater on the screws 5 Fit the bottom bracket found in the fixing kit in the slot at the base of the heater and screw the bracket to the wall Test that the heater is now securely fixed to the wall Operation IMPORTANT OBJECTS O2. XDI m plex Installation and Operating Instructions Dimplex Low Wattage Panel Heaters Models DXLWP400 DXLWP4O00TI INDUKLWPRG __ Issue 6 BEAB Approved DXLWP800 DXLWP800TI N amp ARLWP800TI Dimensions millimetres Models Specification DXLWP400 400W Neon Heat Switch DXLWP4O0TI 400W Neon Heat Switch 24 Hour Timer DXLWP800 800W Neon Heat Switch DXLWP800TI N 800W Neon Heat Switch 24 Hour Timer ARLWP800TI 800W 2 Neon Heat Switches 24 Hour Timer 600 mm 400W 800 mm 800W 500 mm THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE Important Safety Advice WARNING THIS APPLIANCE MUST NOT BE USED INA BATHROOM WARNING DO NOT USE THIS HEATER IN THE IMMEDIATE SURROUNDINGS OF A BATH ASHOWER ORA SWIMMING POOL WARNING THIS HEATER MUST NOT BE LOCATED IMMEDIATELY BELOW A FIXED SOCKET OUTLET The plug must be accessible after heater installation DO NOT USE THE HEATER UNTIL THE FEET OR WALL BRACKETS ARE FITTED CORRECTLY FOLLOW these instructions carefully The heater carries a warning DO NOT COVER to alert the user to the risk of fire that exists if the heater is accidentally covered Models DXLWP400TI DXLWPS800TIN and ARLWPS800TI can be set to switch on automatically Remember to observe all safety warnings at all times This appliance is not intended for use by children or other persons without assistance or supervision if their physical sen
3. uninterrupted by the timer settings The heat selector switch will control the output see Using the heater Position Auto operation DO NOT disconnect this heater from the mains supply unless it is being taken out of use e g in Summer or for storage otherwise the timer clock will stop Setting the time of day To set the time of day rotate the timer dial clockwise indicated by the arrow until the correct time of day is opposite the reference mark gt see Fig 4 The 24 hour clock is used e g time shown for 3 pm is 15 15 00hrs Setting the Auto ON and OFF times To set the timer 1 Using your finger tip or the tip of a pencil push in as many segments as necessary around the dial according to the times you don t require heat see Fig 4 Each segment pushed in switches the heater OFF for that part of the hour All other segments will be ON For example Fig 5 shows the timer set to switch the heater ON between 7 ja am and 9 am and between 4 pm and 7 00 am 9 00 am 9 30 pm Fig 5 2 You can select as many ON periods as you like within the 24 hour day The settings will repeat every day until changed 3 To change ON and OFF times simply push in any ON segments you wish to cancel and pull out new ON segments as required 4 00 pm 9 30 pm Switching to auto Set the heat selector and thermostat fo
4. Blue wire to the terminal marked N or coloured Black DO NOT connect the Brown Live or the Blue Neutral wires to the Earth terminal of your 13 amp plug If the terminals of the plug are unmarked or you are in any doubt consult a qualified electrician CAUTION If you use this heater in conjunction with a thermal control programme controller timer or any other device which switches the heater on automatically observe all safety warnings at all times Positioning the Heater Select the position for the heater ensuring there is clearance from any furniture and fittings of at least 150mm above the heater 50mm below wall mounted and 25mm each side Curtains must not be closer than 150mm from the top of the heater Free Standing Operation see Fig 1 NEVER USE THE HEATER FREE STANDING WITHOUT THE FEET FITTED FEET ARE PACKED SEPARATELY IN CARTON 1 Lay the heater on its front 2 Remove the two socket head screws from the base of the heater using the hexagon key supplied 3 Place feet over base of heater align holes and engage hook on foot into the recess on the back of the heater see Fig 1 4 Replace the screws but do not overtighten a TIT Fig 1 Rear View 7 Trt yo Recess 4 par ee A n ok i oy ef ee Tie ff ie he ea i I iim T BE N Installation The Fixing Kit should contain 1 Drilling Template 3 Screws 3 Rawlplugs 1 Mounting Bracket and 1 Hexagon Key
5. R CLOTHING MUST NOT BE PLACED ON THIS HEATER Before using the heater ensure that all warnings and instructions have been read carefully OPERATION SINGLE RATED MODELS Models DXLWP400 DXLWP400TI DXLWP800 and DXLWP800TI N Turn the heater on using the switch on the right side of the heater the switch will be illuminated OPERATION DUAL RATED MODEL Model ARLWP800TI The two switches on the side of the heater control the heat output Both switches illuminated indicates maximum output Top switch only illuminated indicates 500W output on 800W model Bottom switch only illuminated indicates 300W output on 800W model Note on models fitted with a timer at least one switch must be illuminated for the heater to operate MODELS WITH TIMER see Fig 3 DXLWP400TI and DXLWPS800TIN 1 Switch The switch on the side of the heater turns the heater on Note This switch must be in the on position before the heater will operate ARLWP800TI 2 Switches The two switches on the side of the heater control the amount of heat available as described above Operation Dual Rated Model NOTE At least one switch must be in the On position before the heater will operate Models with Timer DXLWP400TI DXLWP800TI N amp ARLWP800TI Set the amp O slide switch on the timer Fig 3 to Position O Heating Off un BOBS Position Manual operation This setting allows power to the heater
6. r the heat output required Check that the clock shows the correct time of day Set the O slide switch to see Fig 4 the convector will switch ON and OFF according to the timer settings see Fig 5 IMPORTANT NOTES Remember to observe all safety warnings when operating the heater on auto setting unattended or attended If the mains supply to the heater is interrupted the timer clock will stop until power is restored reset the time of day to ensure correct ON and OFF times Cleaning WARNING ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER Do not use detergents abrasive cleaning powder or polish of any kind on the body of the heater Allow the heater to cool then wipe with a dry cloth to remove dust and a damp cloth not wet to clean off stains Be careful not to allow moisture into the heater Recycling For electrical products sold within the European Community At the end of the electrical products useful life it should not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice in your country After Sales Service Your product is guaranteed for three years from the date of purchase Within this period we undertake to repair or exchange this product free of charge subject to availability provided it has been installed and operated in accordance with these instructions Your rights under thi
7. s guarantee are additional to your statutory rights which in turn are not affected by this guarantee Should you require after sales service you should contact our customer services help desk on 0870 727 0101 It would assist us if you can quote the model number series date of purchase and nature of the fault at the time of your call The customer services help desk will also be able to advise you should you need to purchase any spares Please do not return a faulty product to us in the first instance as this may result in loss or damage and delay in providing you with a satisfactory service Please retain your receipt as proof of purchase C The product complies with the European Safety Standards EN60335 2 30 and the European Standard Electromagnetic Compatibility EMC EN55014 EN60555 2 and EN60555 3 which cover the essential requirements of EEC Directives 73 23 and 89 336 Glen Dimplex UK Limited UK customer help line 8 00AM 6 00PM Mon Fri 8 30AM 1 00PM Sat Millbrook House Grange Drive Customer Services Hedge End Southampton Hampshire S030 2DF Republic of Ireland c Glen Dimplex UK Limited 0870 7270101 0870 7270102 customer services glendimplex com 01 8424833 All rights reserved Material contained in this publication may not be reproduced in whole or in part without prior permission in writing of Glen Dimplex UK Limited
8. sory or mental capabilities prevent them from using it safely Children should be supervised to ensure that they do not play with the appliance If young children the aged or infirm are likely to be left in the vicinity of the heater we advise that adequate precautions should be taken We recommend a guard be fitted to ensure contact with the heater is avoided and objects cannot be inserted into the product If the mains lead is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard For further information please contact our guard supplier direct on Tel No 01603 667957 or in case of difficulty or for further advice contact the Customer Helpline Electrical Connection WARNING THIS APPLIANCE MUST BE EARTHED If the socket outlets in your home are not of the 13 amp BS1363 type they will not accept the plug connected to this heater therefore cut off the plug When cut off this plug can constitute a shock hazard if inserted into a socket outlet It must therefore be disposed of safely Before wiring the appropriate plug please note that the wires in this mains lead are coloured in accordance with the following code GREEN YELLOW EARTH BLUE NEUTRAL BROWN LIVE Connect the Green Yellow wire to the terminal marked E or the earth symbol or coloured Green or Green Yellow Connect the Brown wire to the terminal marked L or coloured Red Connect the
Download Pdf Manuals
Related Search