Dell 2009W Computer Monitor User Manual
Contents
1. Ar Ue Place the stand on a flat surface and follow these steps to attach the monitor stand 1 Fit the groove on the back of the monitor to the two tabs on the upper part of the stand 2 Lower the monitor so that the monitor mounting area snaps on to or locks on to the stand Connecting Your Monitor A caution Before you begin any of the procedures in this section follow the Safety Instructions To connect your monitor to the computer perform the following steps instructions Turn off your computer and disconnect the power cable Connect either the white digital DVI D or the blue analog VGA display connector cable to the corresponding video port on the back of your computer Do not use both cables on the same computer Use both the cables only when they are connected to two different computers with appropriate video systems Connecting the White DVI Cable Connecting the Blue VGA Cable III K NOTE The graphics are used for the purpose of illustration only Appearance of the computer may vary After you have completed connecting the DVI VGA cable follow the procedure below to connect the USB cable to the computer and complete your monitor setup Connect the upstream USB port cable supplied to an appropriate USB port on your computer Connect USB peripherals to the downstream USB ports rear or side on the monitor See rear or bottom view for details Plug the power cables for your computer and mon2. Solving Problems Dell 2009W Flat Panel Monitor User s Guide Troubleshooting Your Monitor Common Problems Product Specific Problems Universal Serial Bus Specific Problems Dell Soundbar Troubleshooting A CAUTION Before you begin any of the procedures in this section follow the Safety Instructions Troubleshooting Your Monitor Self Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly If your monitor and computer are properly connected but the monitor screen remains dark run the monitor self test by performing the following steps 1 Turn off both your computer and the monitor 2 Unplug the video cable from the back of the computer To ensure proper Self Test operation remove both the Digital white connector and the Analog blue connector cables from the back of computer 3 Turn on the monitor The floating dialog box should appear on screen against a black background if the monitor cannot sense a video signal and is working correctly While in self test mode the power LED remains green Also depending upon the selected input one of the dialogs shown below will continuously scroll through the screen 1 Auto Detect Analog Input NO YGA CABLE 1 Auto Detect Digital Input C25 NO DYI D CABLE 2 Analog Input JI NO VGA CABLE 3 Digital Input 05m NO DYI D CABLE 4 This box also appears during normal system ope
3. m Removable pedestal and VESA 100 mm mounting holes for flexible mounting solutions Plug and play capability if supported by your system m On Screen Display OSD adjustments for ease of set up and screen optimization m Software and documentation CD includes an information file INF Image color Matching File ICM and product documentation Energy Saver feature for Energy Star compliance m Security lock slot Identifying Parts and Features Front View Front View Front panel controls Label Description 1 Input Source select 2 OSD Menu Select button 3 Brightness amp Contrast Down button 4 Auto adjust Up button 5 Power button with power light indicator Back View EG A 7 QUER A AA A i ini f 17177 ee UN KO O 3 Back view Back View with monitor stand Label Description Use VESA mounting holes 100mm 1 Behind attached base plate Use to mount the monitor 2 Barcode serial number label Refer to this label if you need to contact Dell for technical support 3 Security lock slot Use a security lock with the slot to help secure your monitor 4 Dell Soundbar mounting brackets Attach the optional Dell Soundbar 5 Regulatory rating label Lists the regulatory approvals 6 Stand removal button Press to release the stand 7 Cable management slot Help organize cables by placing them through the slot 8 odedownirelease button Push the monitor down press
4. Analog Input In Power Save Mode Press Computer Power Button or Any Key on Keyboard or Move Mouse OR Digital Input In Power Save Mode Press Computer Power Button or Any Key on Keyboard or Move Mouse Activate the computer and the monitor to gain access to the OSD K NOTE This monitor is ENERGY STAR compliant as well as TCO 99 TCO 03 power management compatible Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor Pin Assignments VGA Connector Pin 15 pin Side of the Connected Signal Cable __ Number 1 Video Red 2 Video Green 3 Video Blue 4 GND 5 Self test 6 GND R 7 GND G 8 GND B 9 Computer 5V 3 3V 10 GND sync 11 GND 12 DDC data 13 H sync 14 V sync 15 DDC clock DVI Connector Pin 24 pin Side of the Connected Signal Cable Number 1 TMDS RX2 TMDS RX2 TMDS Ground Floating DDC Clock 2 3 4 5 Floating 6 7 DDC Data 8 Floating 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 TMDS RX1 TMDS RX1 TMDS Ground Floating Floating 5V 3 3V power Self test Hot Plug Detect TMDS RXO TMDS RX0 TMDS Ground Floating Floating TMDS Ground TMDS Clock TMDS Clock Universal Serial Bus USB Interface This section gives you information about the USB ports that are available on the left side of your monitor K NOTE This monitor supports High Speed Certified USB 2 0 interface Tr
5. the button to unlock the monitor and then lift the monitor to the desired height Side View USB connectors downstream Left view Right view Bottom View nn Bottom view Bottom view with monitor stand Label Description AC power cord connector DC power connector for Dell Soundbar DVI connector VGA connector USB upstream port a vr WN Pp USB downstream ports Monitor Specifications The following sections give you information about the various power management modes and pin assignments for various connectors for your monitor Power Management Modes If you have VESA s DPM compliance display card or software installed in your PC the monitor can automatically reduce its power consumption when not in use Mode If the computer detects input from keyboard mouse or other input devices the monitor automatically resumes functioning The following table shows th of this automatic power saving feature VESA Modes Horizontal Sync Vertical Sync Video Power Indicator Power Consur Normal operation with Dell Soundbar and USB active Active Active Active Green 70 W maximu Normal operation Active Active Active Green 42 W typical Active off mode Inactive Inactive Blanked Amber Less than 2 W Switch off Off Less than 1 W The OSD will only function in the normal operation mode When the menu or plus buttons are pressed in Active off mode one of the following messages will be d
6. video cable connector Restart the computer in the safe mode Safety Related Issues Visible signs of Do not perform any troubleshooting steps smoke or sparks Contact Dell immediately Intermittent Problems i Ensure that the video cable connecting the monitor to the computer is connected properly and is secure Reset the monitor to Factory Settings Perform monitor self test feature check to determine if the intermittent problem occurs in self test mode Missing Color Picture missing Perform monitor self test feature check color Ensure that the video cable connecting the monitor to the computer is connected properly and is secure Check for bent or broken pins in the video cable connector Wrong Color Picture color not Change the Color Setting Mode in the Color Settings OSD to Graphics or Video depending to the good application Try different Color Preset Settings in Color Settings OSD Adjust R G B value in Color Settings OSD if the Color Management is turned off Change the Input Color Format to PC RGB or YPbPr in the Advance Setting OSD Image retention from a Faint shadow from Use the Power Management feature to turn off the monitor at all times when it is not in use for more static image left on the the static image information see Power Management Modes monitor for a long period displayed appears Alternatively use a dynamically changing screensaver of time on the screen
7. Dell 2009W Flat Panel Monitor User s Guide About Your Monitor Solving Problems Product Features Troubleshooting Your Monitor Identifying Parts and Controls Common Problems Monitor Specifications Product Specific Problems Universal Serial Bus USB Interface Universal Serial Bus USB Specific Problems Plug and Play Capability Troubleshooting the Dell Soundbar Maintenance Guidelines Setting Up the Monitor Appendix Attaching the Stand Safety Instructions Connecting the Monitor FCC Notice U S Only and Other Regulatory Information Organizing the Cables Contacting Dell Attaching the Soundbar Optional Removing the Stand Operating the Monitor Using the Front Panel Controls Using the On Screen Display OSD Setting the Optimal Resolution Using the Dell Soundbar Optional Using the Tilt Swivel and Vertical Extension Rotating the monitor Adjusting the Rotation Settings of Your Operating System Notes Notices and Cautions K NOTE A NOTE indicates important information that helps you make better use of your computer NOTI CE A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem A CAUTION A CAUTION indicates a potential for property damage personal injury or death Information in this document is subject to change without notice 2008 Dell Inc All rights reserved Reproduction in any manner whatsoever without the written permission of Dell Inc is strict
8. HD YPbPr is suitable for HD video playback over DVI PC RGB is suitable for normal PC graphics display over DVI To achieve the different color mode for PC and Mac You can choose between a Graphics and a Video mode If your computer is connected to your monitor choose Graphics If a DVD STB or VCR is connected to your monitor choose Video To achieve the different color domain for PC RGB and HD YPbPr HD YPbPr is suitable for HD video playback over DVI PC RGB is suitable for normal PC graphics display over DVI Mode suitable for desktop applications Mode for multimedia applications example video playback Mode suitable for game applications Mode to emulate 72 NTSC color Warm mode is selected to obtain a redder tint This color setting is typically used for color intensive applications photograph image editing multimedia movies etc Cool Mode is selected to obtain a bluish tint This color setting is typically used for text based applications spreadsheets programming text editors etc O or E Use the or button to increase or decrease each of the three colors R G B independently in single digit increments from O ti 100 You can choose different color presets for different viewing modes Mode suitable for movie playback Mode suitable for game applications Mode suitable for sports scenes Mode suitable for nature scenes User Preset Use the plus and minus buttons to increase or decrease each of th
9. ansfer speed Data Rate Power Consumption High speed 480 Mbps 2 5W Max each port Full speed 12 Mbps 2 5W Max each port Low speed 1 5 Mbps 2 5W Max each port USB Upstream Connector 12 Mi a 34 Pin Number 4 pin Side of the connector 1 DMU 2 VCC 3 DPU 4 GND USB Downstream Connector 1 2 3 4 Pin Number 4 Pin Side of the Signal Cable 1 VCC 2 DMD 3 DPD 4 GND USB Ports 1 upstream rear 4 downstream 2 on rear 2 on left side K NOTE USB 2 0 functionality requires a USB 2 0 capable computer K NOTE The monitor s USB interface works only when the monitor is on or in power save mode If you turn off the monitor and then turn it on the attached p to resume normal functionality Plug and Play Capability You can install the monitor in any Plug and Play compatible system The monitor automatically provides the computer system with its Extended Display Identificat Channel DDC protocols so the system can configure itself and optimize the monitor settings Most monitor installations are automatic you can select differe information about changing the monitor settings see Operating the Monitor Flat Panel Specifications Screen type Screen dimensions Preset display area Horizontal Vertical Pixel pitch Viewing angle Luminance output Contrast ratio Dynamic contrast ratio Faceplate coating Backlight Response Time Color gamut Typical Active matrix TFT LCD 20 inches 20 inch vi
10. ck environmental factors Relocate the monitor and test in another room Missing Pixels LCD screen has Cycle power on off Pixel that is permanently off is a natural defect that can occur in LCD technology Stuck on Pixels Cycle power on off i Pixel that is permanently off is a natural defect that can occur in LCD technology Brightness Problems Picture too dim or Reset the monitor to Factory Settings too bright Auto Adjust via OSD Adjust brightness amp contrast controls via OSD Geometric Distortion Screen not Reset the monitor to Factory Settings centered correctly Auto Adjust via OSD Adjust brightness amp contrast controls via OSD NOTE When using 2 DVI D the positioning adjustments are not available Horizontal Vertical Lines Screen has one or Reset the monitor to Factory Settings more lines Perform Auto Adjust via OSD Adjust Phase and Pixel Clock controls via OSD Perform monitor self test feature check and determine if these lines are also in self test mode Check for bent or broken pins in the video cable connector NOTE When using 2 DVI D the Pixel Clock and Phase adjustments are not available Synchronization Problems Screen is Reset the monitor to Factory Settings scrambled or Perform Auto Adjust via OSD appears torn Adjust Phase and Pixel Clock controls via OSD Perform monitor self test feature check to determine if scrambled screen appears in self test mode Check for bent or broken pins in the
11. e three colors R G B independently in single digit increments from O to 100 Changes the color of the image to green H Changes the color of the image to purple NOTE Hue adjustment is only available for video input This feature can make the color of the video image shift to green or purple This is also used to adjust for desired flesh tone color Use or to adjust the hue from 0 to 100 makes the video image look more monochrome pp makes the video image look more colorful NOTE Saturation adjustment is only available for video input Exit Menu DISPLAY SETTINGS Display Setting submenu Back Horizontal Position Vertical Position Sharpness Pixel Clock Phase Dynamic Contrast Display Info Display Reset Exit Menu Display Setting submenu for VGA input Push YY to exit the OSD main menu Display Setting submenu for DVI D input Sharpness Dynamic Contrast On Display Info Display Monitor Information Display Reset Reset to Default Display Settings Exit Menu Display Monitor Information Reset to Default Display Settings Back to Contents Page Setting Up the Monitor Dell 2009W Flat Panel Monitor User s Guide Attaching the Stand Connecting the Monitor Organizing the Cables Attaching the Dell Soundbar optional Removing the Stand Attaching the Stand K NOTE The stand is detached and extended when the monitor is shipped from the factory
12. ewable image size 433 44 mm 17 06 inches 270 90 mm 10 67 inches 0 258 mm 160 vertical typ 170 horizontal typ 300 cd m 2 typ 1000 to 1 typ 2000 to 1 typ Antiglare with hard coating 3H CCFL 4 edgelight system 5ms typical 102 2009W color gamut typical is based on CIE1976 102 and CIE1931 92 test standards Back to Contents Page Appendix Dell 2009W Flat Panel Monitor User s Guide Safety Instructions FCC Notice U S Only and Other Regulatory Information Contacting Dell A caut ON Safety I nstructions CAUTI ON Use of controls adjustments or procedures other than those specified in this documentation may result in exposure to shock electrical hazards and or mechanical hazards For information on safety instructions see the Product Information Guide FCC Notices U S Only and Other Regulatory Information For FCC notices and other regulatory information see the regulatory compliance website located at http www dell com regulatory_compliance Contacting Dell For customers in the United States call 800 WWW DELL 800 999 3355 K NOTE If you do not have an active Internet connection you can find contact information on your purchase invoice packing slip bill or Dell product catalog Dell provides several online and telephone based support and service options Availability varies by country and product and some services may not be available in your a
13. h screen savers The video input from the movement of the first mouse will activate the display As you cycle through the inputs appear the following messages to indicate currently selected input source It may take 1 or 2 seconds for the image to appear 1 AUTO DETECT ANALOG TJ 1 AUTO DETECT DIGITAL E 2 ANALOG INPUT qT 3 DIGITAL INPUT If either VGA or DVI D input is selected and both VGA and DVI D cables are not connected a floating dialog box as shown below appears 1 Auto Detect Analog Input NO YGA CABLE 1 Auto Detect Digital Input WE NO DVI D CABLE 2 Analog Input J NO VGA CABLE 3 Digital Input Sam NO DYI D CABLE Use the MENU button to launch the on screen display OSD and select the OSD Menu See Accessing the Menu System OSD Menu Select Use this button for direct access to the Brightness and Contrast control menu Brightness Contrast Hot Key Brightness Contrast Exit Menu Use these buttons to navigate and adjust the slider bar decrease increase ranges controls in the OSD Down and Up E Auto Adjust Use this button to activate automatic setup and adjust menu The following dialog appears on a black screen as the monitor self adjusts to the current input AUTO ADJUSTMENT IN PROGRESS Auto Adjustment allows the monitor to self adjust to the incoming video signal After using Auto Adjustment you can further tune you
14. ion is only available when you are using the analog VGA connector Use the INPUT SOURCE menu to select between different video signals that may be connected to your monitor Exit Menu Back VGA Push 8 to go back to the main menu Select VGA input when you are using the analog VGA connector Push 8 to select the VGA input source DVI D Select DVI D input when you are using the Digital DVI connector Push to select the DVI input source Scan for Push 8 to scan for available input signals Source s 8 Exit Menu Push 8 to exit the OSD main menu PRESET Use the Preset Modes to adjust the color setting mode and color temperature SETTING Preset setting submenu Back Input Color Format Gamma Color Setting mode Color Presets VGA DVI D Input Desktop Mode Multimedia Mode Game Mode sRGB Mode Warm Mode Cool Mode Custom R G B Mode Presets Mode Video Movie Mode Game Mode Sports Mode Nature Mode Hue Saturation Back Back Input Color Format Input Color Format Gamma Color Setting Mode Graphics Color Setting Mode Preset Modos Movie Preset Mode Game Multimedia Sports Game Nature sRGB ine We 50 Warm Saturation BERN 50 Cool Color Reset Reset to Default Color Settings Custom R G B Exit Menu Exit Menu Push to go back to the main menu To achieve the different color domain for PC RGB and HD YPbPr
15. itor into a nearby outlet Turn on the monitor and the computer If your monitor displays an image installation is complete If it does not display an image see Solving Problems Use the cable holder on the monitor stand to organize the cables Organizing the Cables ULLI 21 IT 1 T an After attaching all the necessary cables to your monitor and computer See Connecting Your Monitor for cable attachment use the cable management slot to organize all cables as shown above Attaching the Soundbar NOTICE Do not use with any device other than the Dell Soundbar K NOTE Soundbar Power Connector 12V DC output is for optional Dell Soundbar only Working from the rear of the monitor attach the Dell Soundbar by aligning the two slots with the two tabs along the bottom rear of the monitor Slide the Dell Soundbar to the left until it snaps into place Connect the Dell Soundbar with the DC power connector u en Insert the mini stereo plug from the rear of the Dell Soundbar into the computer s audio output jack Removing the Stand K NOTE To prevent scratches on the LCD screen while removing the stand ensure that the monitor is placed on a clean surface Complete the following steps to remove the stand 1 Rotate the stand to allow access to the stand release button 2 Press and hold the Stand release button 3 Lift the stand up and away from the monitor Back to Contents Page Back to Contents Page
16. ly forbidden Trademarks used in this text Dell the DELL logo are trademarks of Dell Inc Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation Adobe is a trademark of Adobe Systems Incorporated which may be registered in certain jurisdictions ENERGY STAR is a registered trademark of the U S Environmental Protection Agency As an ENERGY STAR partner Dell Inc has determined that this product meets the ENERGY STAR guidelines for energy efficiency Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Dell Inc disclaims any proprietary interest in trademarks and trade names other than its own Model 2009W January 2008 Rev A00 Back to Contents Page About Your Monitor Dell 2009W Flat Panel Monitor User s Guide Product Features Identifying Parts and Controls Monitor Specifications Universal Serial Bus USB Interface Plug and Play Capability Maintenance Guidelines Product Features The Dell 2009W flat panel display has an active matrix thin film transistor TFT liquid crystal display LCD The monitor features include m 20 inch 508 mm viewable area display m 1680 x 1050 resolution plus full screen support for lower resolutions Wide viewing angle to allow viewing from a sitting or standing position or moving side to side m Tilt swivel vertical extension and rotate adjustment capabilities
17. r monitor by using the Pixel Clock Coarse and Phase Fine controls under DISPLAY SETTINGS NOTE Auto Adjust does not occur if you press the button while there are no active video input signals or attached cables Use the Power button to turn the monitor on and off The green LED indicates the monitor is on and fully functional An amber LED indicates DPMS power save mode Power button with power light indicator Using the On Screen Display OSD Menu Accessing the Menu System K NOTE If you change the settings and then either proceed to another menu or exit the OSD menu the monitor automatically saves those changes The changes are also saved if you change the settings and then wait for the OSD menu to disappear 1 Push the MENU button to launch the OSD menu and display the main menu Main Menu for Analog VGA Input O EN e EN 3 ES DIR BRIGHTNESS AUTO INPUT PRESET DISPLAY OTHER amp CONTRAST ADJUST SOURCE MODES SETTINGS SETTINGS or Main Menu for non Analog non VGA Input X EJ a Es BRIGHTNESS INPUT PRESET DISPLAY OTHER amp CONTRAST SOURCE MODES SETTINGS SETTINGS E NOTE AUTO ADJUST is only available when you are using the analog VGA connector Push the and buttons to move between the setting options As you move from one icon to another the option name is highlighted See the following table for a complete list of all the options available for the monitor 3 Push the MENU but
18. ration if the video cable becomes disconnected or damaged 5 Turn off your monitor and reconnect the video cable then turn on both your computer and the monitor If your monitor screen remains blank after you use the previous procedure check your video controller and computer because your monitor is functioning properly Common Problems The following table contains general information about common monitor problems you might encounter and the possible solutions Common Symptoms What You Possible Solutions Experience No Video Power LED off No picture Ensure that the video cable connecting the monitor and the computer is properly connected and secure Verify that the power outlet is functioning properly by using any other electrical equipment Ensure that the power button is depressed fully No Video Power LED on No picture or no Increase brightness amp contrast controls via OSD brightness Perform monitor self test feature check Check for bent or broken pins in the video cable connector Poor Focus Picture is fuzzy Perform Auto Adjust via OSD blurry or ghosting Adjust the Phase and Pixel Clock controls via OSD Eliminate video extension cables Reset the monitor to Factory Settings Change the video resolution to the correct aspect ration 16 10 Shaky J ittery Video Wavy picture or fine movement Perform Auto Adjust via OSD Adjust the Phase and Pixel Clock controls via OSD Reset the monitor to Factory Settings Che
19. rea To contact Dell for sales technical support or customer service issues Visit support dell com Verify your country or region in the Choose A Country Region drop down menu at the bottom of the page Click Contact Us on the left side of the page Select the appropriate service or support link based on your need Choose the method of contacting Dell that is convenient for you 0 UNI Back to Contents Page Back to Contents Page Operating the Monitor Dell 2009W Flat Panel Monitor User s Guide Using the Front Panel Controls Using the On Screen Display OSD Menu Setting the Optimal Resolution Using the Dell Soundbar Optional Using the Tilt Swivel and Vertical Extension Rotating the monitor Adjusting the Rotation Display Settings of Your System Using the Front Panel Use the control buttons on the front of the monitor to adjust the characteristics of the image being displayed As you use these buttons to adjust the controls an OSD shows the numeric values of the characteristics as they change Front panel Button Description Use Input Source Select button to select between two different video signals that may be connected to your monitor VGA input DVI D input Input Source Select p If both VGA and DVI cables are connected to one PC this monitor displays an image automatically as long as a video signal is present in either VGA or DVI outputs On a display connected to two PCs set equal time for bot
20. ton once to activate the highlighted option 4 Push the O and buttons to select the desired parameter Fa 3 Push 8 to enter the slide bar and then use the O or button according to the indicators on the menu to make your changes 6 Select the back option to return to the main menu or exit to exit the OSD menu Menu and Description Submenus x EXIT Select to exit the main menu BRIGHTNESS Use this menu to activate Brightness Contrast adjustment amp CONTRAST l Brightness Contrast Exit Menu Back Push 8 to go back to the main menu Brightness Brightness adjusts the luminance of the backlight Push the button to increase brightness and push the O button to decrease brightness min 0 max 100 Contrast Adjust Brightness first and then adjust Contrast only if further adjustment is necessary Push the button to increase contrast and push the button to decrease contrast min 0 max 100 The Contrast function adjusts the degree of difference between darkness and lightness on the monitor screen Exit Menu Push 8 to exit the OSD main menu Even though your computer recognizes your monitor on startup the Auto Adjustment function optimizes the display settings for use with your particular setup Pa AUTO ADJUST AUTO ADJUSTMENT IN PROGRESS NOTE In most cases Auto Adjust produces the best image for your configuration NOTE AUTO ADJUST opt
Download Pdf Manuals
Related Search