Crimestopper Security Products SV-9155 Automobile Electronics User Manual
Contents
1. 10 LENGTH T CABLE H VIDEO ADAPTER PLUG CAM 1 V1 Reverse Image Input Connect to Reverse ee t Audio Inputs NOT USED gt Camera V2 Normal Image Input Connect to External Video Source Camera Power Plug YELLOW RCA Video Output CAM 2 REVERSE CAMERA e Before making any power connections to the vehicle disconnect the Ground terminal of the vehicle battery to avoid any short circuits e All plugs should be fully inserted into the connectors and secured tightly with electrical tape to assure the best connection A loose connection may cause malfunctioning of the unit MONITOR CONTROLS CAM Select d MONITOR CONTROLS 1 CAM SEL This button combines two function Press this button to toggle between the VI and V2 Inputs Press and hold it for 2 seconds to turn off the power to the monitor This will put the monitor into Standby mode Press it again to turn the power back on MENU CONTRAST CONTROL To adjust the contrast of the screen Press the MENU button and then select CONTRAST on the screen Use the and buttons to increase or decrease the picture contrast BRIGHTNESS CONTROL To adjust the brightness of the screen Press the MENU button and select BRIGHTNESS on the screen Use the and buttons to increase or dec2. 12V Switched IGN On i VEHICLE IGNITION OREN Y E Choose a convenient place to run the cable either down the left side or right side A Pillar of the vehicle The left side is usually the easier side Remove the trim panel from the A Pillar and route the cable down the pillar to the dash board In most vehicles there will be a wire harness for the dome light inside the A Pillar of the vehicle Use a wire tie or electrical tape to secure the cable to this wire harness Re Install the trim panel Make sure that the cable does not interfere with the mounting clips or screws of the trim panel This may cause damage to the cable and the trim panel and may cause the trim panel to not fit back into position properly Connect the RED wire to a 12V or 24V DC Ignition power terminal which is energized when the key is turned to the Ignition or On position Connect the GREEN trigger wire to the 12V or 24V Reverse Light wire Connect the BLACK wire to a suitable Ground on the vehicle Connect the Grey V1 connector to the video output of the reverse camera V1 is the priority input and will always auto switch when the vehicle is shifted into reverse Connect the Grey V2 connector to the video output of any external video device DVD VCR etc 12V Reverse Light A VEHICLE REVERSE LIGHT SV 9155 MIRROR 0 BLACK Chassis Ground
3. as this could cause injury if the airbags are deployed Make sure to connect the mirror to the correct voltage Failure to do so may result in damage to the mirror or injury to the vehicle occupants Do not submerge the mirror under water The mirror is not waterproof and this will damage the electrical components inside of it The Mirror has built in circuitry to reverse the image so objects on the right of vehicle appear on the right and objects on the left appear on the left when looking at the monitor See Reverse Imaging in next section for more information Do not attempt to take apart the mirror under any circumstances Do not operate the monitor if the mirror housing has been damaged MIRROR MONITOR INSTALLATION 1 A Oo NP oa o 10 Remove the OEM Rear View Mirror from the vehicle Usually the OEM mirror should unscrew from a mounting plate on the vehicle s windshield Do not use excessive force when removing the factory mirror Some factory rear view mirrors may have Reading Lamps or Map Lights built into them In order to remove this type of mirror there will be a wiring harness that will need to be unclipped before you can proceed with the removal of the mirror itself Make sure the vehicle owner is aware that the SV 9155 does not have any lamps built into it and that they will be losing this accessory once the factory mirror is removed Once the factory mirror is removed place the SV 9155 into the po
4. RED in color No Image will be displayed on the monitor Press the CAM SEL D button to activate the video inputs Or simply shift the vehicle into reverse to engage the reverse camera If your vehicle has been parked in direct sun light this can result in a considerable rise in temperature inside the vehicle Allow the unit to cool off before operating MAINTENANCE Clean the unit with a slightly damp soft cloth Make sure to turn Power off before cleaning Do not use liquid cleaners or aerosol cleaners to clean the mirror Never use strong solvents such as thinners or benzene These may damage the finish of the unit Never poke or push any objects of any kind through the ventilation holes of the unit Objects may touch the electronic components inside the unit causing it to short circuit and could result in a fire or electric shock Do not attempt to service this unit by yourself Opening or removing any of the outside covers will expose you to electrical components which may cause injury Opening of any of the covers will also void the warranty of the mirror Refer to an authorized dealer for servicing SPECIFICATIONS LCD Profile Wide Screen Ratio 16 9 4 2 Resolution 320 V x 234 H TV Lines View Angle U D L R 25 45 45 45 Operating Temp 20C 70 C Brightness cd m 200 Storage Temp 30 C 80 C Contrast Ratio 400 1 Dimensions mm 280 L x 91 W x 30 D Response Time in ms at 25 C 15 Weight Oz 490 w
5. SV 9155 4 2 Replacement Rear View Mirror Monitor INSTALLATION INSTRUCTIONS The SV 9155 is a replacement Rear View Mirror It replaces your factory mirror and adds the convenience of a 4 2 LCD screen which can be used for a reverse and an external DVD source The Reverse Camera Input will automatically switch on when the vehicle is dropped into reverse The SV 9155 can be hooked up to any SecurView or PlateCam camera FEATURES e Replacement Rear View Mirror with Built In 4 2 LCD Screen for viewing Reverse Camera Compatible with any Camera which uses an RCA video output Provides extra safety precaution when backing up Maintains the Factory look of the vehicle Optional Normal Image and Reverse Image Compatible with 70 80 of GM Ford and Toyota vehicles Compatible with 12V and 24V DC vehicles Built In Interface to allow user to switch between to different video inputs High Low voltage and short circuit protection Reverse camera input will appear on screen whenever vehicle is shifted into reverse Anti Glaring treatment on Screen INSTALLATION INSTALLATION PRECAUTIONS 1 Secure the mirror tightly to the windshield so that it can not become loose under any circumstances Sudden braking accidents etc and cause injuries to the occupants of the vehicle Do not install the mirror in an area that is in close proximity with an airbag
6. ith bracket Power Supply 12V 24V DC Power Consumption lt 7W DISCLAIMER Under no circumstances shall the manufacturer or distributor of the SV 9155 Mirror be held liable for consequential or incidental damages sustained in connection with the use of the SV 9155 Rear Vision System The SV 9155 is designed as a safety enhancement device and is in no way intended as a replacement for rear view mirrors side view mirrors or physically checking the surroundings when backing a vehicle Always check surroundings for safety when backing Objects on the monitor are closer than they appear Any changes or modifications in construction of this device will void the warranty CRIME www crimestopper com email crimestopper com Phone 800 998 6880 FAX 805 581 9500 2009 Crimestopper Security Products 5 12 2009
7. rease the brightness of the monitor COLOR CONTROL To adjust the color of the screen Press the MENU button and select COLOR on the screen Use the and buttons to increase or decrease the color contrast of the screen NORMAL MIRROR IMAGE Some reverse cameras have built in circuitry to mirror the image so objects on the right of vehicle appear on the right and objects on the left appear on the left when looking at a standard monitor If your camera does not have this function then you can choose it in the SV 9155 menu You can set Normal Mirror imaging for CAM1 and CAM2 separately To adjust Press the MENU button and select MIR1 OFF on the screen Press the and buttons to set the screen to Mirror or Normal Image on CAM1 You can set the CAM2 image the same way PARKING ASSIST This can help the user to properly judge distance when parking Press the MENU button and choose DASH ON on the screen Use the and buttons to activate The parking assist line only appears when the vehicle is in reverse At this time the dash can be adjusted horizontally by pressing the or buttons Adjust the line to the appropriate position for your actual parking condition Once this is done the setting will be locked in memory OPERATION amp GENERAL MAINTENANCE OPERATION When the Ignition key is turned to the Accessory or ON position 12V power is supplied to the mirror The front LED light will turn on solid
8. sition of where the factory mirror was located for a fest fit Adjust the angle of the SV 9155 to the best position by rotating the ball joint of the adjustable mounting bracket on the back of the mirror Remove the screw and silver lug form the base of the SV 9155 mounting bracket Slide SV 9155 Mounting Bracket over the factory mounting plate on the windshield Make sure that the mounting bracket fits over the entire windshield mounting plate Re insert the screw into the mounting bracket and secure the mirror tightly over the factory mounting plate DO NOT overturn the mounting screw This will cause the screw s threads to strip and may also damage the threads inside the mounting bracket itself Route the electrical cable of the SV 9155 up the windshield and underneath the headliner of the vehicle NOTE The holes in the back and the bottom of the unit are provided for ventilation to prevent overheating of the unit and to ensure reliable operation of the monitor equipment These holes must not be blocked with any kind of electrical tape or silicon If the ventilation holes are blocked this could cause damage to the monitor Remove Silver Lug Remove Screw BRACKET ADJUSTMENT Adjustable Mounting Bracket Windshield SV 9155 Mirror Mounting Screw Cable SIDE MIRROR MOUNTING NOTE Mounting Bracket of SV 9155 should slide over the factory mounting plate on windshield WIRING 1 eo
Download Pdf Manuals
Related Search