Creative 8022 Network Router User Manual
Contents
1. Type ipconfig renew and press the ENTER key Your IP address and Subnet Mask change to the above values n Windows 98 SE Windows ME After setting up your ADSL Router turn on your computer Click Start Settings Control Panel Double click the Network icon In the Network dialog box that appears click the Configuration tab Click the name of your Ethernet card for example TCP IP gt PRO 100 Management Adapter 10 100 and then click the Properties button In the TCP IP Properties dialog box that appears click the IP Address tab Click the Obtain an IP address automatically option to select it and click the OK button Click the OK button When Windows prompts you to restart your computer click the Yes button The computer restarts To check the IP address assigned to your Network Adapter i Click Start Run ii When the Run dialog box appears type winipcfg in the Open box then click the OK button The next dialog box may take a minute or two to appear so do not restart your computer or abort this operation prematurely iii In the IP Configuration dialog box that appears click the arrow next to the first box and then click the name of your network device to select it Verify that your IP address is 192 168 1 xxx and your Subnet Mask is 255 255 255 0 If not go to steps iv and v below iv Click the Release button and then click the Renew button Your IP address and Subnet Mask change to the ab2. CREATIVE Broadband BLASTER ADSL Router 8022 Product Registration Registering your product ensures you receive the most appropriate service and product support available You can register your product during installation or at www creative com register Please note that your warranty rights are not dependent on registration Creative Knowledge Base Resolve and troubleshoot technical queries at Creative s 24 hour self help Knowledge Base Go to www creative com select your region and then select Support Customer Support Services amp Warranty You can find Customer Support Services Warranty and other information in the User Documentation CD Customer Support Services d support lt region gt lt language gt support chm Warranty d warranty lt region gt lt language gt warranty chm Please keep your Proof of Purchase for the duration of the Warranty period User s Guide d manual lt language gt manual chm replace d with the drive letter of your CD ROM DVD ROM drive lt region gt with the region you are in and lt language gt with the language that the document is in Keep this document for future reference PN 235 10270 Before You Begin Write down your ADSL Router model and serial numbers and the MAC address found at the bottom of your router You will need to provide the model and serial numbers when contacting Customer Support Services You may also need to provide the MAC addresses to a ne
3. nternet Service Provider ISP in the respective boxes E ADSL Router Configuration Manager GUI Microsoft Internet Explorer File Edit View Favorites Tools Help E Back gt l a y Search Favorites 04 oa E 3 Address a http 192 168 1 1 hag pages home htm v GS Search Web go Gbiblocked fF Autorii options CREATIVE ADSL Router Home Quick Configuration System Mode Quick Configuration Use this page to quickly configure the system Lan Wan ATM Interface o Bridgin Routine Operation Mode Enabled Services Encapsulation PPPoE LLC Admin VPI 0 VCI 35 Bridge Disabled IGMP Disabled IP Address 0 0 0 0 Subnet Mask 0 0 0 0 C Enable Use DHCP Disable Default Route Enabled z Gateway IP Address 0 0 0 0 Primary DNS Server 0 Secondary DNS Server 0 2005 Creative Technology Ltd All rights reserved E Done l Internet Figure 2 Type the PPP Username and PPP Password provided by your ISP and click the Submit button Refer to your User s Guide to learn how to enable different functions for PPPoA and PPPoE configurations as well as how to configure other types of connections Copyright 2005 Creative Technology Ltd All rights reserved Microsoft and Windows are registered trademarks of Microsoft Corporation Broadband Blaster is a trademark of Creative Technology Ltd All brand or product names mentioned herein are trademarks or registered trademarks of their respective
4. ove values Click the OK button to close the IP Configuration dialog box After configuring your Network Interface Card you need to configure your ADSL Router See Configuring your ADSL Router Configuring your ADSL Router Before proceeding make sure that you have configured your Network Interface Card successfully Your ADSL Router can have a number of different configurations This section only covers the most common configuration PPPoA PPPoE Routed Configuration Your ADSL service provider can tell you which configuration works best for you For more information on other configuraions refer to your User s Guide PPPoA PPPoE Configuration DO NOT turn off the computer or router when the router configuration is being Start Internet Explorer In the Address box type http 192 168 1 1 and press the ENTER key A dialog box similar to Figure 1 appears prompting you for a username and password Type admin in the User Name and Password boxes Viking User name E admin Password sasssa Remember my password Figure 1 Click the OK button The Creative ADSL Router 8022 home page appears Click the Quick Configuration link on the left pane Select Enabled from the Operation Mode list box Select PPPoA VC Mux or PPPoE LLC from the Encapsulation list box Type the VPI and VCI values provided by your I
5. owners and are hereby recognised as such
6. r Network Interface Card Configuring your Network Interface Card Make sure that the computer you are using has a functioning Network Interface Card The default settings of your ADSL Router are e IP address 192 168 1 1 e Subnet Mask 255 255 255 0 In Windows XP or Windows 2000 After setting up your ADSL Router turn on your computer Click Start Settings Control Panel or Start Control Panel For Microsoft Windows XP users double click the Network Connections icon For Windows 2000 users click the Network and Dial Up Connections icon Right click the Local Area Connection icon and then click Properties In the Local Area Connection Properties dialog box that appears select Internet Protocol TCP IP and then click the Properties button In the Internet Protocol TCP IP Properties dialog box that appears click the Obtain an IP address automatically option Click the OK button In the Local Area Connection Properties dialog box that appears click the OK button To check the IP address assigned to your Network Adapter i Click Start Programs or All Programs if you are in Windows XP Start menu mode Accessories gt Command Prompt ii When the Command Prompt dialog box appears type ipconfig and press the ENTER key Verify that your IP address is 192 168 1 xxx and your Subnet Mask is 255 255 255 0 If not go to steps iii and iv below iii Type ipconfig release and press the ENTER key iv
7. twork administrator if you plan to use your device for a large network such as in a school or office System Requirements Be sure that your computer meets the following minimum system requirements Network Interface Card NIC installed CD ROM Drive Internet Explorer 6 0 ADSL service running on your telephone line 7 Installing your Hardware Before setting up your ADSL Router be sure that the Network Interface Card in your computer is installed and functioning properly 1 Connect the RJ 45 cable to the Ethernet ports on your computer and router 2 Locate a telephone wall outlet with a running ADSL service and unplug any telephone cable that is connected to it 3 Connect one end of the RJ 11 phone cable to the telephone wall outlet Connect the other end to the ADSL port of your router Connect the small round plug of the power adapter to the router s DC IN Power connector and plug the other end into a power outlet Turn on the power supply and router Power connector ADSL port Ethernet ports Reset button AC iS5V ADSLLINE RESET ETHERNET 700mA_ ON OFF Telephone wall outlet Power outlet Ethernet il Power adapter RJ 11 cable Before using your ADSL Router you will need to configure your Network Interface Card For detailed instructions see Configuring you
Download Pdf Manuals
Related Search