Craftsman 315.2121 Saw User Manual
Contents
1. DUST BAG See Figure 3 The dust bag fits over the exhaust port on the upper blade guard To install it remove the dust guide from the exhaust port Then squeeze the two metal clips to open the mouth of the bag and slide it on the exhaust port Release the clips The metal ring in the bag should lock in between the grooves on the exhaust port For more efficient operation empty dust bag when no more than half full This will permit better air flow through the bag DUST BAG EXHAUST PORT TABLE EXTENSIONS See Figure 4 To install table extensions insert the ends of the extensions into the holes in the sides of the base Secure them in place by positioning a clamp bracket under each table extension beneath the miter table Orient each clamp bracket as shown in figure 4 Secure each clamp bracket in place with a clamp bracket screw The clamp bracket screw threads through the clamp bracket and tightens against bottom of miter table securing clamp bracket against table extension SAW VIEWED FROM BELOW n t CLAMP BRACKET TABLE EXTENSION STOP BLOCK See Figures 5 and 6 The stop block is useful as a stop for cutting multiple pieces to the same length It can be installed on either table extension on either side of the saw base E Slide the stop block on the back arm of either table extension then insert the table extension into the saw base See Figure 5 E Use the small wing screw to secure the stop block t2. Owner s Manual CRAFTSMAN ACCESSORIES FOR MODEL NOS 315 212100 AND 315 212110 10 in 254 mm COMPOUND MITER SAW ltem No 924310 924350 Save this manual for future reference A CAUTION Read and follow m SAFETY all Safety Rules and Operating m LOOSE PARTS instructions before first use of a INSTALLATION this product a SERVICES Customer Help Line 1 800 932 3188 Sears Roebuck and Co Hoffman Estates IL 60179 USA Visit the Craftsman web page www sears com craftsman 972000 603 2 00 RULES FOR SAFE OPERATION READ ALL INSTRUCTIONS E READ THESE INSTRUCTIONS AND THE IN E ALWAYS WEAR SAFETY GLASSES Everyday STRUCTIONS FOR THE 315 212100 COM eyeglasses have only impact resistant lenses they POUND MITER SAW THOROUGHLY before are NOT safety glasses ee ae E ALWAYS DISCONNECT SAW FROM POWER E KNOW YOUR POWER TOOL Read the owner s SUPPLY BEFORE MAKING ADJUSTMENTS OR manual for the Compound Miter Saw carefully ADDING ACCESSORIES Make sure the switch is Learn the saw s applications and iimitations as well off when reconnecting to power supply nk specific potential hazards related to this E SAVE THESE INSTRUCTIONS Refer to them frequently and use to instruct other users If you E KEEP THE WORK AREA CLEAN Cluttered work loan someone this tool loan them these instruc areas and work benches invite accidents DO NOT tions also leave tools or pieces of wood on the saw while it is in operation Look for this symbol to p
3. o the table extension See Figure 5 E Loosen the small wing screw and adjust the stop block the desired distance from the blade for the cut to be made STOP BLOCK SMALL WING SCREW lt MITER SAW BASE TABLE EXTENSION Fig 5 E Tighten small wing screw securely Make a test cut in scrap material and measure the length of the workpiece E Make any necessary adjustments WARNING When using the work clamp with the stop block install the clamp on the stop block side of the blade This will eliminate the possibility of the saw catching the loose end and kicking up Failure to heed this warning can result in serious personal injury Fig 6
4. oint out important safety precautions It means attention Your safety is involved LOOSE PARTS LIST The following accessories are included with item no 224310 and 224350 m Work Clamp E Small Wing Screw E Dust Bag E Clamp Bracket 2 E Table Extensions 2 E Clamp Bracket Screws 2 E Stop Block E Owner s Manual WORK CLAMP DUST BAG TABLE EXTENSIONS g SCREW STOP BLOCK SMALL WING SCREW CLAMP BRACKET Fig 1 A WARNING The use of attachments or accessories not listed might be hazardous 2 INSTALLATION A WARNING To prevent accidental starting that could cause possible serious personal injury assemble all parts to your saw completely before connecting it to power supply Saw should never be connected to power supply when you are assembling parts making adjustments installing or removing blades or accessories or when not in use WORK CLAMP See Figure 2 The work clamp provides greater control by clamping the workpiece to the fence t also prevents the workpiece from creeping toward the saw blade This is very helpful when cutting compound miters To install the work clamp place the shaft of the clamp in either hole in front of the miter table base Rotate the knob on the clamp to move it in or out as needed A WARNING Make sure the saw blade or blade guard will not hit the work clamp assembly when cutting 35 to 45 angles Failure to heed this warning can result in serious personal injury
Download Pdf Manuals
Related Search