Compaq DA-11411 Computer Hardware User Manual
Contents
1. 1 BL p Class interconnects 2 in BL p Class server blade enclosure interconnect switch shown 2 BL20p server blades 8 in BL p Class server blade enclosure 3 BL p Class power enclosure with hot plug power supplies 6 QuickSpecs ProLiant BL20p and p Class system Overview Configuration Steps e For a complete configuration of the ProLiant BL20p do the following 1 Select BL p Class server blades Single Intel Pentium Ill 1 40 GHz processor 512 MB ECC SDRAM 2 X 256MB 230040 B21 or Two Intel Pentium IIl 1 40 GHz processors 1 GB ECC SDRAM 2 X 512MB 257959 B21 Not available in N2. DA 11411 Single Phase Model Three Phase Model Dimensions Height 5 25 in 13 34 cm 5 25 in 13 34 cm Width 27 15 in 68 96 cm 27 15 in 68 96 cm Depth 17 60 in 44 7 cm 17 60 in 44 7 cm Weights No hot plug power supplies 47 5 1b 21 55 kg 41 51b 21 55 kg All hot plug power supplies 99 5 Ib 45 13 kg 125 5 1b 56 93 kg Input requirements Rated input voltage Rated input frequency Rated input current per side Rated input power per side 200 VAC to 240 VAC 50 Hz to 60 Hz 24A 5760 W 200 VAC to 240 VAC line to line 50 Hz to 60 Hz 24A per phase 9976 W Power cord 1 NEMA L6 30P per side 1 NEMA L15 30 per side Output voltage Rated output voltage 48 8 VDC to 54 VDC 48 8 VDC to 54 VDC specifications Rated output current 99A 170A Rated output power 4298 W 8310 W Nominal power 4158 W at 208 VAC 7202 W at 208 VAC Ambienttemperature Operating 50 to 95 F 10 to 35 C 50 to 95 F 10 to 35 C range See note Shipping 22 to 140 F 30 to 60 C 22 to 140 F 30 to 60 C Relative humidity Operating 20 to 80 20 to 80 aia Non operating 5 to 95 5 to 95 Wet bulb temperature Operating 82 4 F 28 C 82 4 F 28 C Non operating 101 7 F 38 7 C 101 7 F 38 7 C Note Operating temperature has an altitude derating of 34 F 1 C per 1 000 ft 304 8 m No direct sunlight Upper operating limit is 10 000 ft 3 048 m or 70Kpa 10 1 psia Upper non operating limit is 30 0
3. Memory Standard 512MB PC133 MHz Registered ECC SDRAM DIMM Memory 2 X 256 MB 1 processor model Maximum 4096 MB Standard 1024MB PC133 MHz Registered ECC SDRAM DIMM Memory 2 x 512 MB 2 processor model not available in NA Maximum 4096 MB Note Memory must be installed in pairs Network Controller Four NICs total Three Compaq NC3163 Fast Ethernet NIC PCI 10 100 with full WOL Wake On LAN one with PXE support One 10 100 iLO NIC dedicated to management Two NICs are upgradable to 10 100 1000T using the Dual Gigabit Ethernet NC7780 NIC option kit Manageability Integrated Lights Out iLO Management Advanced ASIC on the System Board Internal Storage Hard Drives None ship standard Maximum Internal Storage 145 6 GB internal drive cage 2 x 72 8 GB Wide Ultra3 1 drives Expansion Slots No PCI slots all features are integrated ProLiant BL p Class Server Blade Enclosure and Interconnects ProLiant BL p Class Server 6U 10 5 inch 19 inch wide Blade Enclosure Holds up to 8 ProLiant BL20p servers blades 10 bays per server blade enclosure 8 bays for server blades 2 outside bays for interconnect modules RJ 45 patch panels or GbE interconnect switches Server blades blind mate into the server blade enclosure backplane for power and data connections Up to 6 BL p Class 6U server blade enclosures fit in a 42U rack Server blade management module attached to the back of each BL p Class 6U server blade enclosure to report even
4. Service and Support Compaq Services provides a three year limited warranty including Pre Failure Warranty coverage of hard drives memory and processors fully supported by a worldwide network of resellers and service providers Compaq technical assistance is available 7x24 toll free in the United States and Canada Telephone support services may be covered under warranty or available for an additional fee Note Sever Blade Limited Warranty includes 3 year Parts 3 year Labor 3 year on site support Note Server Blade Enclosure and Interconnects Limited Warranty includes 3 year Parts 3 year Labor 3 year on site support A full range of CarePaq packaged hardware and software services e Installation and start up e Extended coverage hours and enhanced response times e System management and performance services e Availability and recovery services Note For more information customer resellers can contact http Avww compag com services Please see the following URL regarding Warranty Information For Your Compaq Products http www compaq com support warranty_upgrades web_statements 176738 html For additional information regarding Worldwide Limited Warranty and Technical Support please see the following URL ftp ftp compag com pub supportinformation ejourney 176738 pdf Note These Web sites are available in English only Note Certain restrictions and exclusions apply Consult the Compaq Customer Support Center at 1 8
5. RMON1 MIB RFC 1757 groups 1 2 3 and 9 and Ethernet MIB RFC1643 Network transfer rate 10 Base T half duplex 10 Mbps 10 Base T full duplex 20 Mbps 100 Base TX half duplex 100 Mbps 100 Base TX full duplex 200 Mbps 1000 Base TX half duplex 1000 Mbps 1000 Base TX full duplex 2000 Mbps 1000 Base SX full duplex 2000 Mbps Connector RJ 45 DB 9 C GbE Interconnect Kit LC fiber RJ 45 DB 9 F GbE Interconnect Kit EMI FCC Class A ICES 003 Class A ASINZS 3548 Class A VCCI Class A Safety UL CUL Listed Accessory Power requirements 48V 1050 mA 50 W maximum per interconnect switch Temperature range Operating 50 to 95 F 10 to 35 C Non operating 22 to 140 F 30 to 60 C Relative humidity Operating 20 to 80 non condensing Non operating 5 to 95 Wet bulb temperature Operating 82 4 F 28 C Non operating 101 7 F 38 7 C Note Operating temperature has an altitude derating of 34 F 1 C per 1 000 ft 304 8 m No direct sunlight Upper operating limit is 10 000 ft 3 048 m or 70Kpa 10 1 psia Upper non operating limit is 30 000 ft 9 144 m or 30 3 KPa 4 4 psia Storage maximum humidity of 95 is based on a maximum temperature of 113 F 45 C Altitude maximum for storage is 70 KPa World Wide Version 4 September 19 2002 21 QuickSpecs ProLiant BL20p and p Class system Technical Specifications Operating and Performance Specifications for Power Enclosures North America Japan
6. to 140 F 30 to 60 C Relative humidity Operating 20 to 80 20 to 80 i Non operating 5 to 95 5 to 95 Wet bulb temperature Operating 82 4 F 28 C 82 4 F 28 C Non operating 101 7 F 38 7 C 101 7 F 38 7 C Note Operating temperature has an altitude derating of 34 F 1 C per 1 000 ft 304 8 m No direct sunlight Upper operating limit is 10 000 ft 3 048 m or 70Kpa 10 1 psia Upper non operating limit is 30 000 ft 9 144 m or 30 3 KPa 4 4 psia Storage maximum humidity of 95 is based on a maximum temperature of 113 F 45 C Altitude maximum for storage is 70 KPa World Wide Version 4 September 19 2002 23 QuickSpecs ProLiant BL20p and p Class system Technical Specifications Operating and Performance Specifications for Power Distribution Devices DA 11411 Power Bus Box Mini Bus Bar Scalable Bus Bar Power enclosures or facility 1 1 2 DC feeds supported 3U each Server blade enclosures 1 3 5 supported 6U each Total rack height of supported 9U 21U 36U enclosures Dimensions Height 5 1 in 12 95 cm 19 45 in 49 40 cm 48 57 in 123 37 cm Width 3 6 in 9 14 cm each 19 74 in 50 14 cm 19 74 in 50 14 cm Depth 3 25 in 0 26 cm 2 2 in 5 59 cm 2 2 in 5 59 cm Weight 3 62 Ib 1 64 kg 13 2 b 59 9 kg 26 Ib 11 79 kg Rated operating voltage 43 2 VDC to 54 VDC 43 2 VDC to 54 VDC 43 2 VDC to 54 VDC Max total power supported 3000 W 9000 W 15 000 W Total max
7. Insight Manager ProLiant and ROMPaq are trademarks of Compaq Information Technologies Group L P in the U S and or other countries Microsoft Microsoft NET and Windows are registered trademarks or trademarks of Microsoft Corporation in the U S and or other countries Intel and Pentium are registered trademarks or trademarks of Intel Corporation in the U S and or other countries Linux is a registered trademark or trademark of Linus Torvalds in the U S and or other countries Red Hat is a registered trademark or trademark of Red Hat Inc in the U S and other countries All other product names mentioned herein may be trademarks of their respective companies Compaq shall not be liable for technical or editorial errors or omissions contained herein The information is provided as is without warranty of any kind and is subject to change without notice The warranties for Compaq products are set forth in the express limited warranty statements accompanying such products Nothing herein should be construed as constituting an additional warranty DA 11411 World Wide Version 4 September 19 2002 27
8. Microsoft NET Server Note For a more complete and up to date listing of supported OS s and versions please visit our OS Support Matrix at ftp fto compag com pub products servers os support matrix 310 pdf Note For an up to date listing of the latest drivers available for the Compaq ProLiant BL p Class please see http www compag com supportifiles server us index html Intelligent Manageability Integrated Lights Out Advanced iLO Virtual Text and Graphical Remote Console Virtual Floppy Virtual Power Button Control Dedicated LAN Connectivity Automatic IP Configuration via DHCP DNS WINS Industry Standard 128 bit Secure Sockets Layer SSL Security IML and iLO Event Logging Support for 12 user accounts with customizable access privileges Automatic Server Recovery 2 ASR 2 Compag Insight Manager 7 Redundant ROM Remote Flash ROM ROM Based Setup Utility RBSU Advanced Configuration and Power Interface Specification Ready ACPI Server Health Logs Compaq Redundant Power Supply Utility Pre Failure Warranty covers processors as well as hard drives and memory Compaq Interconnect Switch Management System and Utilities interconnect switch option Integrated Management Log IML Off Line Backup Processor capability Dynamic sector repairing and drive parameter tracking with Smart Array controllers Redundant adaptive load balancing NIC Support Advanced features such as Graphical Remote Console and V
9. NA JPN 230769 001 INTL 230769 421 Three phase power enclosure holds a max of six power supplies no need to order additional power supplies with this option kit Power enclosures and power supplies can also be purchased separately see options list for part numbers PLUS 5 Select power distribution Scalable bus bar Supports up to 5 server blade enclosures 240560 B21 or Mini bus bar Supports up to 3 server blade enclosures 240559 B21 or Power Bus Box connects 1 power enclosure to 1 server blade enclosure 240562 B21 DA 11411 World Wide Version 4 September 19 2002 Interconnect Switch fibre or copper based Patch panel BL p Class Interconnects maet eE D E Ra HE S OR i i i i Facility DC BL p Class power enclosure and power supplies i OR i Bus boxes o Lael Dee re Scalable bus bar Mini bus bar BL p Class power distribution QuickSpecs ProLiant BL20p and p Class system Standard Features Server Blade ProLiant BL20p Server Blade Processor Intel Pentium Ill FC PGA processor 1 40GHz Upgradability Upgradable to dual processing Cache Memory 512 KB Level 2 Cache Chipset ServerWorks HE SuperLite Chipset Note For more information regarding ServerWorks please see the following URL http www serverworks com products overview html
10. for EMEA 3 yrs 24x7 on site hardware maintenance with a 6 hour repair time for a fully 207269 022 configured ProLiant BL p Class server blade enclosure with interconnects and up to 8 server blades power enclosure with power supplies and power distribution 6 3 part number for EMEA 3 yrs 9x5 on site hardware maintenance with a 4 hour response for a fully configured 302329 001 ProLiant BL p Class server blade enclosure with interconnects and up to 8 server blades power enclosure with power supplies and power distribution Electronic CarePaq service 6 3 part number for US 3 yrs 9x5 on site hardware maintenance with a 4 hour response for a fully configured 207266 021 ProLiant BL p Class server blade enclosure with interconnects and up to 8 server blades power enclosure with power supplies and power distribution Electronic CarePaq service 6 3 part number for EMEA 3 yrs 24xT on site hardware maintenance with a 4 hour response for a fully configured 302330 001 ProLiant BL p Class server blade enclosure with interconnects and up to 8 server blades power enclosure with power supplies and power distribution Electronic CarePaq service 6 3 part number for US DA 11411 World Wide Version 4 September 19 2002 16 QuickSpecs ProLiant BL20p and p Class system Options Service and Support Offerings Hardere Services 4 Hour On site Service continued i 3 yrs 24x7 on site hardware
11. http activeanswers compag com aaconfi qurator PowerCalc BL20p xls e BLp Class power enclosure provides shared external redundant power e Power enclosure is 3U and holds up to 6 hot plug power supplies e Choose single phase or three phase power e BLp Class power enclosure with power supplies not needed if using facility 48VDC 10 in this case purchase DC option kit ProLiant BL p Class Power Distribution e Distributes power from the power enclosure to the server blade enclosures e Three power distribution choices e BLp Class scalable bus bar e BL p Class mini bus bar e BL p Class power bus box BL p Class server blade server blade enclosure interconnects and power enclosure protected by a limited three year warranty with optional service uplifts available e Note Power requirements for a ProLiant BL p Class system 200V 240V AC 30 amp or facility DC 48V 10 COMPAQ DA 11411 World Wide Version 4 September 19 2002 42U Rack with ProLiant BL p Class System Installed g T EIS REG Zi LES 6 6
12. 9142 and Compag Rack 9842 36U Side Panel 120671 B21 Note The 36U Side Panel PN 120671 B21 supports the Compaq Rack 9136 600mm Stabilizer Option Kit 120673 B21 800mm Stabilizer Option Kit Opal 234493 B21 Note The 800mm Stabilizer Kit PN 234493 B21 supports the Rack 9842 only Grounding Rack Option Kit 120682 B21 Stabilizer Option Kit 120673 B21 Rack Blanking Panel Multi 169940 B21 Note Kit includes four panels in 1U 2U 4U and 8U 9142 Extension Kit 120679 B21 Note The 9142 Extension Kit PN 120679 B21 supports the Compaq Rack 9142 only Rack Blanking Panels 1U 189453 B21 Note The Rack Blanking Panels PN 189453 B21 contains 10 each of 1U Rack Blanking Panels 2U 189453 B22 Note The Rack Blanking Panels PN 189453 B21 contains 10 each of 2U Rack Blanking Panels 3U 189453 B23 Note The Rack Blanking Panels PN 189453 B21 contains 10 each of 3U Rack Blanking Panels 4U 189453 B24 Note The Rack Blanking Panels PN 189453 B21 contains 10 each of 4U Rack Blanking Panels 5U 189453 B25 Note The Rack Blanking Panels PN 189453 B21 contains 10 each of 5U 9136 Extension Kit 218216 B21 9142 Short Rear Door 218217 B21 Note The 9142 Short Rear Door PN 218217 B21 supports the Compaq Rack 9142 only Split Rear Door Opal 254045 B21 Note The Split Rear Door PN 254045 B21 supports the 600 mm wide 42U 9000 series rack 9136 Short Rear Door 218218 B21 9142 Split Rear Door 254045 B21 9000 10000 Series Offset B
13. Electronic CarePaq service 6 3 part number for EMEA Note For more information customer resellers can contact http www compag com services Note This Web site is available in English only DA 11411 World Wide Version 4 September 19 2002 17 QuickSpecs Memory ProLiant BL20p and p Class system ProLiant BL20p Server Blade 2P Model not available in NA STANDARD MEMORY 1024 MB PC133 MHz Registered ECC SDRAM DIMM installed 2 x 512 MB SDRAM DIMM STANDARD MEMORY PLUS OPTIONAL MEMORY Up to 3072 MB of SDRAM DIMM memory is available with the installation of optional SDRAM DIMM memory expansion kits STANDARD MEMORY REPLACED WITH OPTIONAL MEMORY Up to 4096 MB of SDRAM DIMM memory is available with the removal of standard memory and the installation of optional SDRAM DIMM memory expansion kits Memory Slot 1 2 3 4 Standard 1024 MB 512 MB 512 MB Empty Empty Optional 3072 MB 512 MB 512 MB 1024 MB 1024 MB Maximum 4096 MB 1024 MB 1024 MB 1024 MB 1024 MB Following are memory options available from Compaq e 2048 MB PC133MHz Registered ECC SDRAM Memory Kit 2 x 1024 MB 201695 B21 e 1024 MB PC133MHz Registered ECC SDRAM Memory Kit 2 x 512 MB 201694 B21 e 512 MB PC133MHz Registered ECC SDRAM Memory Kit 2 x 256 MB 201693 B21 e 256 MB PC133MHz Registered ECC SDRAM Memory Kit 2 x 128 MB 201692 B21 ProLiant BL20p Server Blade 1P Model STAND
14. additional 10 100 port dedicated to iLO Management Smart Array 5i Controller integrated on system board None ship standard Up to 145 6 GB maximum with optional hard drives None Plugs vertically into Compaq ProLiant BL p Class Server Blade Enclosure 10 QuickSpecs ProLiant BL20p and p Class system Options ProLiant BL20p Unique Options Dual NC7780 Gigabit Upgrade Module for ProLiant BL20p 230255 B21 Note The Dual NC7780 Gigabit Upgrade Module replaces two of the standard NC3163 Fast Ethernet Embedded WOL Wake On LAN NICs to two 10 10 1000T NC7780 NICs Note The GbE Interconnect Switch options support server NIC speeds to 100 Mbps It is recommended that the patch panel be used with the Dual NC7780 Gigabit Upgrade Module if server NIC speeds to 1000 Mbps are required ProLiant BL p Class Server Blade Enclosure ProLiant Essentials Rapid Deployment 243564 B21 Pack Trial ProLiant BL p Class Server Blade Enclosure 8 ProLiant Essentials Rapid Deployment 281404 B21 Pack Licenses ProLiant BL p Class RJ 45 Patch panel pair 230766 B21 Note Only one interconnect kit required per server blade enclosure ProLiant BL p Class C GbE Interconnect Kit with pair of GbE Interconnect Switches 249655 B21 and two QuadT Interconnect Modules Note Only one interconnect kit required per server blade enclosure ProLiant BL p Class F GbE Interconnect Kit with pair of GbE Interconnect Switches 279720 B21 and two D
15. are not included in this kit Single Power Supply 239161 B21 Facility DC Power Connection 240563 B21 ProLiant p Class Scalable Bus Bar 240560 B21 ProLiant p Class Mini Bus Bar 240559 B21 ProLiant p Class Bus Power Box 240562 B21 DA 11411 World Wide Version 4 September 19 2002 11 QuickSpecs ProLiant BL20p and p Class system Options ProLiant Essentials Value Pack Rapid Deployment Pack 10 User V1 x 269817 B21 Software Note This license allows 10 servers to be managed and deployed via the Deployment Server Note Not necessary if you purchase the server blade enclosure with 8 Rapid Deployment Pack licenses 281404 B21 Rapid Deployment Pack 10 User V1 x Japan 269817 291 Note This license allows 10 servers to be managed and deployed via the Deployment Server Note Not necessary if you purchase the server blade enclosure with 8 Rapid Deployment Pack licenses 281404 B21 Rapid Deployment Pack 1 User V1 x 267196 B21 Note This license allows 1 server to be managed and deployed via the Deployment Server Note Not necessary if you purchase the server blade enclosure with 8 Rapid Deployment Pack licenses 281404 B21 Rapid Deployment Pack 1 User V1 x Japan 267196 291 Note This license allows 1 server to be managed and deployed via the Deployment Server Note Not necessary if you purchase the server blade enclosure with 8 Rapid Deployment Pack licenses 281404 B
16. 00 345 1518 for details DA 11411 World Wide Version 4 September 19 2002 9 QuickSpecs ProLiant BL20p and p Class system Models ProLiant BL20p P1400 512KB 512MB 1P 230040 B21 Processor s Cache Memory Memory Network Controller Storage Controller 1 Intel Pentium III 1 40 GHz standard up to 2 supported 512 KB Level 2 writeback per processor 512 MB Standard 2 X 256MB to 4096 MB PC133 MHz Registered ECC SDRAM DIMM Memory Three Compaq NC3163 Fast Ethernet NIC PCI 10 100 with full WOL Wake On LAN one NIC has PXE support One additional 10 100 port dedicated to iLO Management Smart Array 5i Controller integrated on system board Hard Drives None ship standard Internal Storage Up to 145 6 GB maximum with optional hard drives Optical Drive None Form Factor Plugs vertically into Compaq ProLiant BL p Class Server Blade Enclosure ProLiant BL20p P1400 512KB Processor s 2 Intel Pentium III 1 40 GHz standard up to 2 supported 1GB 2P Cache Memory 512 KB Level 2 writeback per processor 257959 B21 Memory 1024 MB Standard 2 X 512MB to 4096 MB PC133 MHz Registered ECC Not available in North America DA 11411 Network Controller Storage Controller Hard Drives Internal Storage Optical Drive Form Factor World Wide Version 4 September 19 2002 SDRAM DIMM Memory Three Compaq NC3163 Fast Ethernet NIC PCI 10 100 with full WOL Wake On LAN one NIC has PXE support One
17. 00 ft 9 144 m or 30 3 KPa 4 4 psia Storage maximum humidity of 9596 is based on a maximum temperature of 113 F 45 C Altitude maximum for storage is 70 KPa World Wide Version 4 September 19 2002 22 QuickSpecs ProLiant BL20p and p Class system Technical Specifications Operating and Performance Specifications for Power Single Phase Model Three Phase Model Dimensions Enclosures International DA 11411 Height Width Depth 5 25 in 13 34 cm 27 15 in 68 96 cm 17 60 in 44 7 cm 5 25 in 13 34 cm 27 15 in 68 96 cm 17 60 in 44 7 cm Weights No hot plug power supplies All hot plug power supplies 47 5 1b 21 55 kg 99 5 1b 45 13 kg 47 5 1b 21 55 kg 125 5 1b 56 93 kg Input requirements Rated input voltage Rated input frequency Rated input current per side Rated input power per side Power cord 200 VAC to 240 VAC 50 Hz to 60 Hz 24A 5760 W 1 IEC 309 3 pin 32A per side 6 25 A at 48 VDC 200 VAC to 240 VAC line to neutral 50 Hz to 60 Hz 20A per phase 10 552 W 1 IEC 309 5 pin 32A per side Output voltage Rated output voltage 48 8 VDC to 54 VDC 48 8 VDC to 54 VDC specifications Rated output current 99A 180A Rated output power 4798 W 8790 W Nominal power 4598 W at 208 VAC 8790 W at 230 VAC L N Ambienttemperature Operating 50 to 95 F 10 to 35 C 50 to 95 F 10 to 35 C range See note Shipping 22 to 140 F 30 to 60 C 22
18. 21 Service and Support Offerings Hardere Services 4 Hour Onsite Service CarePaq Services f 3 yrs 9x5 on site hardware maintenance with a 4 hour response for a fully configured 274369 002 ProLiant BL p Class server blade enclosure with interconnects and up to 8 server blades power enclosure with power supplies and power distribution 6 3 part number for US 3 yrs 9x5 on site hardware maintenance with a 4 hour response for a fully configured 207266 022 ProLiant BL p Class server blade enclosure with interconnects and up to 8 server blades power enclosure with power supplies and power distribution 6 3 part number for EMEA 3 yrs 24x7 on site hardware maintenance with a 4 hour response for a fully configured 274370 002 ProLiant BL p Class server blade enclosure with interconnects and up to 8 server blades power enclosure with power supplies and power distribution 6 3 part number for US 3 yrs 24x7 on site hardware maintenance with a 4 hour response for a fully configured 207267 022 ProLiant BL p Class server blade enclosure with interconnects and up to 8 server blades power enclosure with power supplies and power distribution 6 3 part number for EMEA 3 yrs 9x5 on site hardware maintenance with a 6 hour repair time for a fully configured 207268 022 ProLiant BL p Class server blade enclosure with interconnects and up to 8 server blades power enclosure with power supplies and power distribution 6 3 part number
19. 21 ProLiant Essentials Workload Management Pack Featuring Resource Partitioning 303284 B21 Manager version 2 0 Note For more information regarding ProLiant Essentials Software please see the following URL http www compag com proliantessentials Note Flexible and volume quantity license kits are available for ProLiant Essentials Value Packs Refer to URL http www compag com proliantessentials or the various ProLiant Essentials Value Pack product QuickSpecs for more information Note These Web sites are available in English only Processor Pentium Ill P1400 512KB Processor Option Kit 234277 B21 Memory SDRAM DIMMs 2048 MB PC133MHz Registered ECC SDRAM Memory Kit 2x1024 MB 201695 B21 1024 MB PC133MHz Registered ECC SDRAM Memory Kit 2x512 MB 201694 B21 512 MB PC133MHz Registered ECC SDRAM Memory Kit 2x256 MB 201693 B21 256 MB PC133MHz Registered ECC SDRAM Memory Kit 2x128 MB 201692 B21 Hard Drives Wide Ultra3 SCSI Universal Hot Plug 72 8 GB Wide Ultra3 SCSI 10 000 rpm Drive 1 232432 B22 36 4 GB Wide Ultra3 SCSI 10 000 rpm Drive 1 176496 B22 18 2 GB Wide Ultra3 SCSI 10 000 rpm Drive 1 142673 B22 36 4 GB Wide Ultra3 SCSI 15 000 rpm Drive 1 232916 B22 18 2 GB Wide Ultra3 SCSI 15 000 rpm Drive 1 188122 B22 Storage Controllers Battery Backed Write Cache Enabler Option Kit 255514 B21 Battery Backed Write Cache Enabler Option Kit Japan 255914 291 Communications Dual NC7780 Gigabit Upgrade Module for ProLiant BL20p 230
20. 255 B21 Note The Dual NC7780 Gigabit Upgrade Module replaces two of the standard NC3163 Fast Ethernet Embedded WOL Wake On LAN NICs to two 10 10 1000T NC7780 NICs Note The GbE Interconnect Switch options support server NIC speeds to 100 Mbps It is recommended that the patch panel be used with the Dual NC7780 Gigabit Upgrade Module if server NIC speeds to 1000 Mbps are required DA 11411 World Wide Version 4 September 19 2002 12 QuickSpecs ProLiant BL20p and p Class system Options BL p Class Server Blade ProLiant BL p Class Server Blade Enclosure ProLiant Essentials Rapid Deployment 243564 B21 Enclosures Pack Trial ProLiant BL p Class Server Blade Enclosure 8 ProLiant Essentials Rapid Deployment 281404 B21 Pack Licenses BL p Class Interconnects ProLiant BL p Class RJ 45 Patch panel pair 230766 B21 Note Only one interconnect kit required per server blade enclosure ProLiant BL p Class C GbE Interconnect Kit with pair of GbE Interconnect Switches 249655 B21 and two QuadT Interconnect Modules Note Only one interconnect kit required per server blade enclosure ProLiant BL p Class F GbE Interconnect Kit with pair of GbE Interconnect Switches 279720 B21 and two DualTSX Interconnect Modules Note Only one interconnect kit required per server blade enclosure BL p Class Power options Note Use p Class sizing tool to help determine power confi
21. A Note Additional options include processors memory and Gb NIC 2 Decide how many BL p Class Server Blade Enclosures to purchase each enclosure can hold up to 8 ProLiant BL20p server blades BL p Class server blade enclosure with 8 Rapid Deployment Pack licenses 281404 B21 or BL p Class server blade enclosure with Rapid Deployment Pack trial 243564 B21 PLUS 3 Select an Interconnect Interconnects are sold in pairs One pair of Interconnects is required with each BL p Class server blade enclosure BL p Class RJ 45 Patch panel with 32 RJ 45 connectors 230766 B21 or ProLiant BL p Class C GbE Interconnect Kit with 4 RJ 45 10 100 1000 T TX T and 4 RJ 45 10 100 T TX uplink connectors 249655 B21 or ProLiant BL p Class F GbE Interconnect Kit with 4 LC 1000 SX and 4 RJ 45 10 100 T TX uplink connectors 279720 B21 PLUS 4 Select BL p Class power enclosure and power supplies based on configuration Use p Class sizing tool to help determine power configuration http activeanswers compag com aaconfi qurator PowerCalc BL20p xls Note Power enclosures and supplies are not needed if using facility DC 48V 10 Single phase power enclosure with four hot plug power supplies NA JPN 239162 001 Single phase power enclosure holds a max of four power supplies no need to order additional power supplies with this option kit INTL 239162 421 or Three phase power enclosure with six hot plug power supplies
22. ARD MEMORY 512 MB PC133 MHz Registered ECC SDRAM DIMM installed 2 x 256 MB SDRAM DIMM STANDARD MEMORY PLUS OPTIONAL MEMORY Up to 2560 MB of SDRAM DIMM memory is available with the installation of optional SDRAM DIMM memory expansion kits STANDARD MEMORY REPLACED WITH OPTIONAL MEMORY Up to 4096 MB of SDRAM DIMM memory is available with the removal of standard memory and the installation of optional SDRAM DIMM memory expansion kits Memory Slot 1 2 3 4 Standard 512 MB 256 MB 256 MB Empty Empty Optional 2560 MB 256 MB 256 MB 1024 MB 1024 MB Maximum 4096 MB 1024 MB 1024 MB 1024 MB 1024 MB Following are memory options available from Compaq e 2048 MB PC133MHz Registered ECC SDRAM Memory Kit 2 x 1024 MB e 1024 MB PC133MHz Registered ECC SDRAM Memory Kit 2 x 512 MB e 512 MB PC133MHz Registered ECC SDRAM Memory Kit 2 x 256 MB e 256 MB PC133MHz Registered ECC SDRAM Memory Kit 2 x 128 MB DA 11411 World Wide Version 4 September 19 2002 201695 B21 201694 B21 201693 B21 201692 B21 18 QuickSpecs ProLiant BL20p and p Class system Technical Specifications Compaq ProLiant BL p Class Server Blade Enclosure Dimensions Height 10 5 in 26 67 cm Width 17 60 in 44 70 cm Depth 28 86 in 73 30 cm Input Specifications Rated input voltage 43 VDC to 53 VDC Nominal 48 VDC Rated input current 62 5 A at 48 VDC Rated input Power 3000 W Individual server bla
23. Note The Rack Blanking Panels PN 253214 B21 contains 10 each of 4U Rack Blanking Panels Graphite 5U 253214 B25 Note The Rack Blanking Panels PN 253214 B21 contains 10 each of 5U 800mm Stabilizer Option Kit Graphite 259488 B21 Note The 800mm Stabilizer Kit PN 255488 B21 supports the Rack 9842 only 600mm Stabilizer Kit Graphite 246107 B21 Baying Kit for Rack 10000 series Carbon 248929 B21 42U Side Panel Graphite Metallic 246099 B21 110V Fan Kit Graphite 257413 B21 Note Roof Mount Includes power cord with IEC320 C13 to NEMA 5 15P DA 11411 World Wide Version 4 September 19 2002 14 QuickSpecs ProLiant BL20p and p Class system Options Rack Options for Compaq Rack 220V Fan Kit Graphite 257414 B21 10000 Series continued Note Roof Mount Includes power cord with IEC320 C13 to NEMA 6 15P 36U Side Panel Graphite Metallic 246102 B21 4TU Side Panel Graphite Metallic 255486 B21 9000 10000 Series Offset Baying Kit 248931 B21 Note This kit can be used to connect 9000 and 10000 series racks in 42U height together Kit contents include hardware for connecting racks and a panel to cover the 100mm gap at the rear of the two racks Rack O ptions for Compaq Rack Baying Coupling Kit 120669 B21 9000 Series 42U Side Panel 120670 B21 Note The 42U Side Panel PN 120670 B21 supports the Compaq Rack
24. QuickSpecs ProLiant BL20p and p Class system Overview nes New Performance dual processor server blade designed with enterprise availability e ProLiant BL20p Server Blade includes Intel Pentium III FC PGA 1 4 GHz processor dual capability e ServerWorks HE SuperLite Chipset e 512 MB or 1024 MB PC133 MHz Registered ECC SDRAM memory 2 x 1 Interleaved Memory expandable to 4 GB e Three NC3163 Fast Ethernet Embedded WOL Wake On LAN NICs standard e Two NICs are upgradable to 10 100 1000T using the Dual Gigabit Ethernet NC7780 NIC option kit e One additional 10 100 port dedicated to Integrated Lights Out iLO Management e Smart Array 5i Controller with optional battery backed write cache integrated on system board e Wide Ultra3 SCSI Drive Cage standard supports up to two 1 Wide Ultra3 hot plug hard drives e Integrated Lights Out iLO Advanced Management ASIC on motherboard e Plugs vertically into 6U enclosure Up to 48 BL20p blades fit in 42U rack ProLiant BL p Class Server Blade Enclosure e Server blades and interconnects blind mate into server blade enclosures for network connection and power e Server blade enclosure is 6U and holds up to 8 ProLiant BL20p server blades and 2 interconnects e 2 types of interconnects available interconnect switches or patch panels ProLiant BL p Class Power Enclosure Use BL p Class sizing tool to determine power based on your configuration
25. TIA 568 100 ohm STP 100 meters 100Base TX Category 5 UTP 100 meters EIA TIA 568 100 ohm STP 100 meters 1000Base T Category 5 UTP 100 meters EIA TIA 568 100 ohm STP 100 meters 1000Base SX 50 125 um Multimode Fiber 400 MHz Km 500 meters 50 125 um Multimode Fiber 500 MHz Km 550 meters 62 5 125 um Multimode Fiber 160 MHz Km 220 meters 62 5 125 um Multimode Fiber 200 MHz Km 275 meters Note For cabling information refer to the Compaq Web site at http www compag com products servers Note This Web site is available in English only DA 11411 World Wide Version 4 September 19 2002 4 QuickSpecs ProLiant BL20p and p Class system Standard Features Power System and Rack Information Compaq ProLiant BL p Class Note To determine power configuration please refer to the ProLiant BL p Class Overview and Planning Power System and Rack Whitepaper and sizing tool please see the following URL Information http www compag com products servers proliant bl p class index html ProLiant BL p Class Power 3U 5 25 inch 19 inch wide 29 inch deep 0 48 meter wide 0 74 meter deep Dual input single phase and three Enclosure phase models available BL p Class power enclosure provides external shared hot plug power Each three phase power enclosure houses up to six hot plug power supplies each single phase power enclosures hold up to four hot plug power supplies to power the BL p Class server blades and int
26. ass doors 165753 001 42U and 163747 001 22U the new processor technology requires the installation of Compaq s new High Airflow Rack Door Inserts 327281 B21 42U 327281 B22 42U 6 pack or 157847 B21 22U to promote enhanced airflow for maximum cooling CAUTION Ifa third party rack is used observe the following additional requirements to ensure adequate airflow and to prevent damage to the equipment o Frontand rear doors If your 42U server rack includes closing front and rear doors you must allow 830 square inches 5 350 sq cm of hole evenly distributed from top to bottom to permit adequate airflow equivalent to the required 64 percent open area for ventilation o Side The clearance between the installed rack component and the side panels of the rack must be a minimum of 2 75 inches 7 cm CAUTION Always use blanking panels to fill all remaining empty front panel U spaces in the rack This arrangement ensures proper airflow Using a rack without blanking panels results in improper cooling that can lead to thermal damage Note For additional information refer to the Setup and Installation Guide or the Documentation CD provided with the server or to the server documentation located in the Support section at the following URL http www5 compag com products servers proliantdl380 index html DA 11411 World Wide Version 4 September 19 2002 8 QuickSpecs ProLiant BL20p and p Class system Standard Features
27. aying Kit 248931 B21 Note This kit can be used to connect 9000 and 10000 series racks in 42U height together Kit contents include hardware for connecting racks and a panel to cover the 100mm gap at the rear of the two racks Rack Options for Compaq Rack High Air Flow Rack Door Insert for 7122 157847 B21 7000 Series and Telco racks High Air Flow Rack Door Insert for 7142 single 327281 B21 High Air Flow Rack Door Insert for 7142 6 pack 327281 B22 Compaq Networking Cable Management Kit 292407 B21 Compaq Networking Recessed Rail Management Kit 292406 B21 Compaq Rack Extension Kit for 7142 154392 B21 DA 11411 World Wide Version 4 September 19 2002 15 QuickSpecs ProLiant BL20p and p Class system Options Rack Options for Compaq Rack Monitor Utility Shelf 303606 B21 10000 9000 and 7000 Series Ballast Option Kit 120672 B21 100kg Sliding Shelf 234672 B21 Rack Rail Adapter Kit 25 depth 120675 B21 Monitor Utility Shelf Graphite 253449 B21 Depth Adjustable Fixed Rail 332558 B21 Cable Management D Rings Kit 168233 B21 Console Management Controller CMC Option Kit 203039 B21 Console Management Controller CMC Sensors Option Kit 203039 B22 Console Management Controller CMC Locking Option Kit 203039 B23 Console Management Controller CMC Smoke Sensor Option Kit 203039 B24 Rack Options for Telco Racks Bus Bar Telco Rail Option Kit 245249 B21 Enclosure Telco Rail Option Kit 266076 B
28. d in its enclosure for this measurement or the measurement leads are properly shielded with Earth grounds applied to the insert World Wide Version 4 September 19 2002 25 QuickSpecs ProLiant BL20p and p Class system Technical Specifications Compaq Rack 10842 Dimensions Total Cabinet Shipping Color 42U optional Height 78 7 in 199 9 cm 85in 215 9 cm Depth 39 691 in 100 82 cm 48 in 121 92 cm Graphite Metallic doors Width 31 5 in 80 01cm 43 5 in 110 49 cm Carbon frame Weight 295 1b 133 8 kg 3351b 151 95 kg Compaq Rack 10647 Dimensions Total Cabinet Shipping Color 47U optional Height 89 96 in 228 5 cm 95 47 in 242 49 cm Depth 39 691 in 100 82 cm 48 in 121 92 cm Graphite Metallic doors Width 24 in 60 96 cm 32 in 81 28 cm Carbon frame Weight 245 Ib 111 kg 284 1b 129 kg Compaq Rack 10642 Dimensions Total Cabinet Shipping Color 42U optional Height 78 7 in 199 90 cm 86 22 in 219 cm Depth 39 691 in 100 82 cm 48 in 121 92 cm Graphite Metallic doors Width 24 in 60 96 cm 32 in 81 28 cm Carbon frame Weight 253 b 114 84 kg 325 Ib 147 52 kg Compaq Rack 10636 Dimensions Total Cabinet Shipping Color 36U optional Height 68 6 in 174 24 cm 75 25 in 191 14 cm Depth 39 691 in 100 82 cm 48 in 121 92 cm Graphite Metallic doors Width 24 in 60 96 cm 32 in 81 28 cm Carbon frame Weight 220 Ib 100 kg 272 1 123 kg Compaq Rack 10622 Di
29. dditional uplinks One 1 RS 232 DB 9 front panel out of band management port Redundant 10 100 cross links ports connecting the two Interconnect Switches Redundant power and cooling inputs Hot plug and hot remove with configuration retention capability Power ON management and per port status and speed LED indicators Reset power momentary push button switch Compaq ProLiant BL Interconnect Switch Management Utilities and User Documentation CD Fully pre configured for rapid deployment and immediate operation ProLiant BL Interconnect Switch Management System and Utilities Full featured web based interface menu driven console interface Telnet SNMP based scripting utility and example scripts SNMP and RMON MIBs BootP and DHCP client port mirroring QoS packet prioritization IGMP multicasting and TFTP server utilities for management of interconnect switch ProLiant BL p Class RJ 45 6U 10 5 inch Plugs into BL p Class 6U server blade enclosures patch panel Used to pass NIC signals from all server blades in server blade enclosure out as RJ 45 connections Two patch panels per kit Supports Gigabit Ethernet network controllers Every BL p Class server blade enclosure 6 R J 45 connectors on the back of each BL p Class 6U RJ 45 patch panel 32 RJ 45 connections per server requires two Interconnect switches OR two blade enclosure RJ 45 patch panels Required Network Cabling 10Base T Categories 3 4 or 5 UTP 100 meters EIA
30. de bay Rated input voltage 43 VDC to 53 VDC Nominal 48 VDC ratings Rated input current 6 25 A at 48 VDC Rated input Power 300 W Temperature range Operating 50 to 95 F 10 to 35 C Non Operating 22 to 140 F 30 to 60 C Relative humidity Operating 20 to 80 non condensing Non Operating 5 to 95 Wet bulb temperature Operating 82 4 F 28 C Non Operating 101 7 F 38 7 C Note Operating temperature has an altitude derating of 34 F 1 C per 1 000 ft 304 8 m No direct sunlight Upper operating limit is 10 000 ft 3 048 m or 70Kpa 10 1 psia Upper non operating limit is 30 000 ft 9 144 m or 30 3 KPa 4 4 psia Storage maximum humidity of 95 is based on a maximum temperature of 113 F 45 C Altitude maximum for storage is 70 KPa Operating and Performance a ae for ProLiant BL20p Server Blade Dimensions Height 1 69 in 4 29 cm Width 10 29 in 26 14 cm Depth 28 00 in 71 12 cm Weight maximum 18 0 Ib 8 17 kg Temperature range Operating 50 to 95 F 10 to 35 C Non operating Shipping 40 to 140 F 40 to 60 C Storage 4 to 140 F 20 to 60 C Relative humidity Operating 10 to 90 non condensing Non operating Shipping 10 to 90 Storage 10 to 95 Maximum wet bulb 82 F 28 C temperature Note Operating temperature has an altitude derating of 34 F 1 C per 1 000 ft 304 8 m No direct sunlight Upper operating limit is 10 000 ft 3 048 m or 70Kpa 10 1 psia Upper non opera
31. erconnects Please use the sizing utility to determine the power needed for each configuration http activeanswers compaq com aaconfigurator PowerCalc BL20p xls Power enclosures and power supplies are not needed if using facility DC 48V DC 10 If using facility DC only Facility DC Power Connection kit part number 240563 B21 is needed BL p Class Power Distribution In the ProLiant BL p Class infrastructure redundant 48 VDC power from the power enclosures or facility DC power is distributed from the power enclosures to the server blade enclosures through the Compaq bus bar System Hinges attach the ProLiant BL bus bars to the rails in a rack The bus bars swing open from the center to enable easy rear access to the server blades and network cables Power is distributed redundantly through independent A and B sided bus bars Three different power distribution solutions are available depending on the maximum number of server blade enclosures planned for the rack e Compaq ProLiant BL p Class scalable bus bar e Compaq ProLiant BL p Class mini bus bar Note To support a full 42U rack of BL20p server blades 6 server blade enclosures two mini bus bars are needed e Compaq ProLiant BL p Class power bus box Power Enclosures Server Blade Enclosures Max Rack Space Supported Supported Occupied Scalable Bus Bar 10r2 lt 5 36U Mini Bus Bar 1 lt 3 21U Power Bus Box 1 1 9U Required Power Source Two 30a
32. guration http activeanswers compag com aaconfiqurator PowerCalc BL20p xls Single Phase Redundant Power Enclosure with 4 power supplies NA JPN 239162 001 Single Phase Power Enclosure holds a maximum of 4 power supplies no need to order additional power supplies with this option kit Single Phase Redundant Power Enclosure with 4 power supplies Intl 239162 421 Single Phase Power Enclosure holds a maximum of 4 power supplies no need to order additional power supplies with this option kit 3 Phase Redundant Power Enclosure with 6 power supplies NA JPN 230769 001 3 Phase Power Enclosure holds a maximum of 4 power supplies no need to order additional power supplies with this option kit 3 Phase Redundant Power Enclosure with 6 power supplies Int l 230769 421 3 Phase Power Enclosure holds a maximum of 4 power supplies no need to order additional power supplies with this option kit Single Phase Power Enclosure empty NA JPN 231710 001 Holds up to 4 power supplies power supplies are not included in this kit Single Phase Power Enclosure empty Int l 231710 421 Holds up to 4 power supplies power supplies are not included in this kit 3 Phase Power Enclosure empty NA JPN 231709 001 Holds up to 6 power supplies power supplies are not included in this kit 3 Phase Power Enclosure empty Int l 231709 421 Holds up to 6 power supplies power supplies are not included in this kit Single Power Supply 239161 B21 Facility DC Power Co
33. ight Manager 7 and other management consoles in case of subsystem or environmental failures For additional information about the Management Agents and other management product from Compaq please visit the management website at http www compaq com manage Note This Web site is available in English only ActiveUpdate is a web based application that keep IT managers directly connected to Compaq for proactive notification and delivery of the latest software updates The latest software drivers and firmware fully optimized and tested for your ProLiant server and options The most advanced configuration analysis reporting and troubleshooting utilities used by Compaq and at your fingertips Health Drivers interface with the Integrated Lights Out ASIC to provide system management support including monitoring of server components event logging and support for the Compaq Insight Management Agents The iLO Management Interface Driver provides access to the iLO management processor for Insight Management Agents This interface is used to provide SNMP alert forwarding and management agent integration Note For more information regarding ProLiant Essentials Software please see the following URL http Avww compaq com proliantessentials Note This Web site is available in English only QuickSpecs ProLiant BL20p and p Class system Standard Features OS Support Microsoft Windows 2000 Advanced Server LINUX Red Hat and SuSE
34. input current at 69 44 A at 43 2VDC 208 32 A at 43 2 VDC 347 2 A at 43 2 VDC minimum voltage equivalent of 175A per feed Total max input current at 62 5 A at 48VDC 187 5 A at 48 VDC 312 5 A at 48 VDC nominal voltage equivalent of 175A per feed Max current per power feed 70A 210A 210A Max local ambient temperature 149 F 65 C 149 F 65 C 149 F 65 C Note All systems support redundant A amp B feeds Scalable bus bar supports dual A and dual B feeds World Wide Version 4 September 19 2002 24 QuickSpecs ProLiant BL20p and p Class system Technical Specifications Operating and Performance Specifications for Facility DC DA 11411 Voltage Nominal input voltage 48 VDC Operating voltage range 48VDC 10 or 43 2 VDC to 52 8 VDC Max Input voltage slew rate 0 5V uS Redundant feed voltages A and B feeds must differ by no more than A amp B 5VDC during steady state operation Ripple Noise 480 mV PARD Overshoot Must remain within regulation limits on all feeds during startup or shutdown Voltage transients Must not exceed 60 VDC Current Max steady state input current 62 5A per server blade enclosure installed at Max steady state current per feed total Power bus boxes Mini bus bars Scalable bus bars 48VDC TO A TOA 210 A 210A 210 A 350A or equivalent of 175A per feed In rush current Must support up to 2X the maximum operating current per server b
35. irtual Floppy are included with the BL p Class server Availability Power redundancy Redundant AC feeds into power enclosures redundant DC feeds from power enclosure to server blade enclosures 1 1 redundant power supplies Two hot plug SCSI hard drive bays and integrated RAID Smart Array 5i on every server blade Battery backed write cache is optional Redundant ROM on each server blade ECC Memory Interconnects Switch Availability Hot plug and hot remove with configuration retention capability Two network connections per server blade bay four NICs total routed to two redundant interconnect switches Redundant inter switch communication with two sets of redundant uplink ports per each interconnect switch IEEE 802 1D Spanning tree protocol support for loop free path redundancy Static IEEE 802 3ad EtherChannel compatible trunking with automatic port load balancing Network adapter teaming network fault tolerance transmit load balancing switch assisted load balancing DA 11411 World Wide Version 4 September 19 2002 7 QuickSpecs ProLiant BL20p and p Class system Standard Features Security Power on password Administrator s password Integrated Lights Out has 12 customizable user accounts and SSL encryption Integrated Lights Out can be disabled via a Global Setting Interconnect Switch multilevel user names and passwords and management interface time out period setting Up to 64 Port based IEEE 802 1Q tagged VLAN
36. lade enclosure 125 A for up to 1 0 mS Input over current Customer provided fusing for facility DC feeds that protects the system from catastrophic over current within 20 uS Fuse should sustain all in rush and operating currents Max Input Current Slew Rate 1A uS Max Rated Power 3000W per server blade enclosure Connections and Cables Compaq provided facility DC cable connection kit e The facility DC connection kit supports the connection of up to four 48VDC RETURN pairs and ground The power cable assemblies consist of 1 0AWG color coded flexible cable rated at 105 C terminated with bus mating connectors at one end and unterminated at the other end The cable length provided enables the customer to route to a fuse panel within or adjacent to the rack Note All systems support redundant A and B feeds Scalable bus bars support dual A and dual B feeds Periodic and random noise PARD Maximum allowable peak to peak ripple and noise as measured at the load on any output channel The ripple and noise is measured over a 20 Hz to 100 MHz frequency band A resistive load non electronic is used for this measurement Each output is by passed to return by a 10uF tantalum capacitor with an ESR less than 100 milli Ohms in parallel with a 0 47 uF ceramic capacitor at the point of load The load cable is 12 feet of twisted wire capable of carrying the current The printed wiring board assembly is installe
37. maintenance with a 4 hour response for a fully configured 207267 021 ProLiant BL p Class server blade enclosure with interconnects and up to 8 server blades power enclosure with power supplies and power distribution Electronic CarePaq service 6 3 part number for EMEA 3 yrs 9x5 on site hardware maintenance with a 6 hour repair time for a fully configured 207268 021 ProLiant BL p Class server blade enclosure with interconnects and up to 8 server blades power enclosure with power supplies and power distribution Electronic CarePaq service 6 3 part number for EMEA 3 yrs 24x7 on site hardware maintenance with a 6 hour repair time for a fully 207269 021 configured ProLiant BL p Class server blade enclosure with interconnects and up to 8 server blades power enclosure with power supplies and power distribution Electronic CarePaq service 6 3 part number for EMEA Installation amp Start up Services Install ProLiant BL p Class server blade enclosure including up to 8 ProLiant BL p Class 274371 002 server blades and interconnects power enclosure with power supplies and power distribution 6 3 part number for US Install ProLiant BL p Class server blade enclosure including up to 8 ProLiant BL p Class 302331 001 server blades and interconnects power enclosure with power supplies and power distribution Electronic CarePaq service 6 3 part number for US Provides for the Installation and Start up of Rapid Deployment Pack on a Custome
38. mensions Total Cabinet Shipping Color 22U optional Height 43 in 109 22 cm 52 25 in 132 72 cm Depth 39 691 in 100 82 cm 48 in 121 92 cm Graphite Metallic doors Width 24 in 60 96 cm 32 in 81 28 cm Carbon frame Weight 176 1b 79 89 kg 225 1b 102 13 kg Compaq Rack 9842 Dimensions Total Cabinet Shipping Color 42U optional Height 78 7 in 199 9 cm 86 22 in 219 cm Depth 35 8 in 90 932 cm 48 in 121 92 cm Opal Width 31 5 in 80 01 cm 38 8 in 98 55 cm Weight 374 Ib 170 kg 440 Ib 200 kg Compaq Rack 9142 Dimensions Total Cabinet Shipping Color 42U optional Height 78 7 in 199 9 cm 83 38 in 211 79 cm Depth 35 8 in 90 932 cm 48 in 121 92 cm Opal Width 23 1 in 60 2 cm 32 in 81 28 cm Weight 253 b 114 84 kg 325 Ib 147 52 kg DA 11411 World Wide Version 4 September 19 2002 26 QuickSpecs ProLiant BL20p and p Class system Technical Specifications Compaq Rack 9136 Dimensions Total Cabinet Shipping Color 36U optional Height 68 6 in 174 24 cm 75 25 in 191 14 cm Depth 35 8 in 90 932 cm 48 in 12 192 cm Opal Width 23 7 in 60 2 cm 32 in 81 28 cm Weight 165 Ib 75 kg 234 Ib 106 kg Compaq Rack 9122 Dimensions Total Cabinet Shipping Color 22U optional Height 43 in 109 22 cm 52 25 in 132 72 cm Depth 35 8 in 90 932 cm 48 in 121 92 cm Opal Width 24 in 60 96 cm 32 in 81 28 cm Weight 176 Ib 79 89 kg 225 b 102 13 kg 2002 Compaq Information Technologies Group LP Compaq the Compaq logo ActiveUpdate CarePaq
39. mp redundant power feeds per power enclosure Connectors NEMA receptacles NA Japan NA 1 phase L6 30 250v 30A 3 wire NA 3 phase L15 30 250V 30A 4 wire EC 309 Pin amp Sleeve connectors International Intl 1 phase 250V 32A 3 pin 2 pole ground Intl 3 phase 380 415V 32A 5 pin 4 pole ground Optimized for power cabling from bottom and network cabling from top For cabling information refer to the Compaq Web site at http www compag com products servers Note This Web site is available in English only DA 11411 World Wide Version 4 September 19 2002 5 QuickSpecs ProLiant BL20p and p Class system Standard Features ProLiant Essentials Foundation Optional ProLiant Essentials Value Optional software offerings that selectively extend the functionality of an Pack Software Packs DA 11411 Insight Manager 7 Management Agents Compaq ActiveUpdate Compaq ROMPaq support software and configuration utilities Compaq Survey Utility and diagnostics utilities Compaq Health Driver Compaq iLO Management Interface Driver World Wide Version 4 September 19 2002 Adaptive Infrastructure to address specific business problems and needs e Rapid Deployment Pack an automated solution for multi server deployment and provisioning enabling companies to quickly and easily adapt to changing business demands e Workload Management Pack provides easier management of complex environment
40. nnection 240563 B21 Power Distribution ProLiant p Class Scalable Bus Bar 240560 B21 ProLiant p Class Mini Bus Bar 240559 B21 ProLiant p Class Bus Power Box 240562 B21 Diagnostic Options ProLiant p Class Diagnostic Station 230743 B21 Note The Diagnostic Station allows access to the ProLiant BL20p server blade and the BL p Class interconnect switch outside of the server enclosure The option provides power and a data interface so that offline upgrade and diagnostic functions may be performed DA 11411 World Wide Version 4 September 19 2002 13 QuickSpecs ProLiant BL20p and p Class system Options Compaq Rack 10000 Series Compaq Rack 10842 42U Pallet 257415 B21 Graphite Metallic Compaq Rack 10842 42U Shock Pallet 257415 B22 Note Not available in North America Compaq Rack 10647 47U Pallet 245160 B21 Compaq Rack 10647 47U Crated 245160 B23 Compaq Rack 10642 42U Pallet 245161 B21 Compaq Rack 10642 42U Shock Pallet 245161 B22 Compaq Rack 10642 42U Crated 245161 B23 Compaq Rack 10636 36U Pallet 245162 B21 Compaq Rack 10636 36U Shock Pallet 245162 B22 Compaq Rack 10636 36U Crate 245162 B23 Compaq Rack 10622 22U Pallet 245163 B21 Compaq Rack 10622 22U Shock Pallet 245163 B22 Compaq Rack 10622 22U Crated 245163 B23 Note B21 pallet used t
41. o ship empty racks shipped on a truck B22 shock pallet used to ship racks with equipment installed by custom systems VARs and Channels B23 crated used for air shipments of empty racks Compaq Rack 9000 Series Opal Compaq Rack 9142 42U Pallet 120663 B21 Compaq Rack 9142 42U Shock Pallet 120663 B22 Compaq Rack 9142 42U Crated 120663 B23 Compaq Rack 9136 36U Pallet 120664 B21 Compaq Rack 9136 36U Shock Pallet 120664 B22 Compaq Rack 9136 36U Crated 120664 B23 Compaq Rack 9122 22U Pallet 120665 B21 Compaq Rack 9122 22U Shock Pallet 120665 B22 Compaq Rack 9122 22U Crated 120665 B23 Compaq Rack 9842 800mm wide 42U Pallet 222192 B21 Note B21 pallet used to ship empty racks shipped on a truck B22 shock pallet used to ship racks with equipment installed by custom systems VARs and Channels B23 crated used for air shipments of empty racks Rack Options for Compaq Rack Rack Blanking Panels Graphite Multi 253214 B26 10000 Series Note Contains one each of 1U 2U 3U and 4U panel Rack Blanking Panels Graphite 1U 253214 B21 Note The Rack Blanking Panels PN 253214 B21 contains 10 each of 1U Rack Blanking Panels Graphite 2U 253214 B22 Note The Rack Blanking Panels PN 253214 B21 contains 10 each of 2U Rack Blanking Panels Graphite 3U 253214 B23 Note The Rack Blanking Panels PN 253214 B21 contains 10 each of 3U Rack Blanking Panels Graphite 4U 253214 B24
42. perating limit is 30 000 ft 9 144 m or 30 3 KPa 4 4 psia Storage maximum humidity of 95 is based on a maximum temperature of 113 F 45 C Altitude maximum for storage is 70 KPa DA 11411 World Wide Version 4 September 19 2002 20 QuickSpecs ProLiant BL20p and p Class system Technical Specifications Operating and Performance Specifications for Interconnect GbE Switch DA 11411 Dimensions Height 10 405 in 26 43 cm Width 1 535 in 3 899 cm Depth 27 697 in 70 35 cm Weight 11 51b 5 2 kg per interconnect switch Performance 3 2 Gbps Switching bandwidth per server enclosure 4 4 Gbps uplink bandwidth per server enclosure 9 6 Million pps aggregate throughput per server enclosure 64 byte packets Full wire speed for all connections Auto negotiation and auto sensing with full duplex support Forwarding mode Store and forward MAC Addresses 8 191 per interconnect switch MAC address based filtering and MAC address packet priority configuring Forwarding table age time Maximum age 10 to 9999 seconds default 3000 seconds Memory 32MB Main 6MB flash and 16MB packet buffer per interconnect switch Compliance IEEE 802 3 802 3u 802 3ab 802 3z 802 1D 802 1p 802 3ac 802 3ad Static 802 1Q and 802 3x SNMP v1 RFC 1157 and RMON v1 RFC 1757 groups 1 2 3 and 9 MIB II RFC 1213 Bridge MIB RFC 1493 Interface MIB RFC 2233 801 1Q MIB RFC 2684
43. r 214545 002 supplied server designated as a Deployment Server Includes the deployment of a single server This new server will be deployed using either one of the pre configured scripts or an image In addition the service will provide for the capture and storage of the configuration of the newly deployed server and orientation on product usage To be delivered during standard office ours standard office days 6 3 part number for US Provides for the Installation and Start up of Rapid Deployment Pack on a Customer 204601 022 supplied server designated as a Deployment Server Includes the deployment of a single server This new server will be deployed using either one of the pre configured scripts or an image In addition the service will provide for the capture and storage of the configuration of the newly deployed server and orientation on product usage To be delivered during standard office ours standard office days 6 3 part number for EMEA Provides for the Installation and Start up of Rapid Deployment Pack on a Customer 204601 021 supplied server designated as a Deployment Server Includes the deployment of a single server This new server will be deployed using either one of the pre configured scripts or an image In addition the service will provide for the capture and storage of the configuration of the newly deployed server and orientation on product usage To be delivered during standard office ours standard office days
44. s improving overall server utilization and enabling Windows 2000 customers for the first time to confidently deploy multiple applications on a single multiprocessor ProLiant Server e Integrated Lights Out Advanced Pack The BL20p includes the advance version of the Integrated Lights Out which includes graphical console and virtual media Insight Manager 7 helps maximize system uptime and performance and reduces the cost of maintaining the IT infrastructure by providing proactive notification of problems before those problems result in costly downtime and reduced productivity Insight Manager 7 is easy to set up and provides rapid access to detailed fault and performance information gathered by the Management Agents One click access to the Remote Insight Lights Out Edition board allows systems administrators to take full graphical control of ProLiant servers in remote locations or lights out data centers Finally Insight Manager 7 in concert with the Version Control Agents and Version Control Repository Manager enables systems administrators to version manage and update system software across groups of Compaq ProLiant servers The Management Agents htto www compag com products servers management agents html form the foundation for Compaq s Intelligent Manageability strategy They provide direct browser based access to in depth instrumentation built into ProLiant servers workstations desktops and portables and send alerts to Ins
45. s per interconnect switch Minimum Rack Requirements Mounts in Compaq and Telco racks and Third Party racks that meet the following criteria e Compatible with 19 inch Standard EIA rail sets e EIA rail to rail depth is 29 30 e Cabinet depth must be at least 36 inch deep overall Additional min 3 5 inch clearance from rear RETMA rail to rear door inclusive in the 36 inch overall depth e Ample room for top and bottom cable egress approximately 8 square inches for full rack configuration with patch panel Must be capable of supporting 1600 Ib for full rack configuration Perforated front and rear doors to accommodate front to back cooling Must have 65 open perforation on server blade enclosure doors to support airflow requirements e Optimized for use with the Compaq 10000 Series racks Note If using Compaq 7000 Series rack Compaq Rack Extension Kit and High Air Flow Rack Door options are required Rack Airflow Requirements e Rack 9000 and 10000 series Cabinets The increasing power of new high performance processor technology requires increased cooling efficiency for rack mounted servers The Compaq 9000 Series Rack and the new 10000 Series Racks provides enhanced airflow for maximum cooling allowing these racks to be fully loaded with servers using the latest processors e Rack 7000 series Cabinets When installing a server with processors running at speeds of 550 MHz or greater in Compaq Rack 7000 series racks with gl
46. ting limit is 30 000 ft 9 144 m or 30 3 KPa 4 4 psia Storage maximum humidity of 95 is based on a maximum temperature of 113 F 45 C Altitude maximum for storage is 70 KPa DA 11411 World Wide Version 4 September 19 2002 19 QuickSpecs ProLiant BL20p and p Class system Technical Specifications Operating and Performance Dimensions Height 10 405 in 26 43 cm Specifications for RJ 45 Patch Panel Width 1 535 in 3 899 cm Depth 21 697 in 70 35 cm Capability IEEE 802 2 802 3 802 3u Network transfer rate 10 Base T half duplex 10 Mbps 10 Base T full duplex 20 Mbps 100 Base TX half duplex 100 Mbps 100 Base TX full duplex 200 Mbps 1000 Base TX full duplex 1000 Mbps Connector RJ 45 Cable support 10 Base TX Categories 3 4 or 5 UTP 2 or 4 pair up to 328 ft 100 m 100 Base TX Category 5 UTP 2 pair up to 328 ft 100 m 1000 Base TX Category 5E 4 pair up to 328 ft 100 m Power requirements 200 mA at 5V DC 500 mA at 48V Temperature range Operating 50 to 95 F 10 to 35 C Non operating 22 to 140 F 30 to 60 C Relative humidity non Operating 20 to 80 condensing Non operating 5 to 95 Wet bulb temperature Operating Non operating 82 4 F 28 C 101 7 F 38 7 C Note Operating temperature has an altitude derating of 34 F 1 C per 1 000 ft 304 8 m No direct sunlight Upper operating limit is 10 000 ft 3 048 m or 70Kpa 10 1 psia Upper non o
47. ts all servers and provide asset and inventory information ProLiant BL p Class Power Redundant 200V 240V AC 30 amp single phase for NA and International Requirements Redundant 208V 30amp 3 phase 4 wire NA Redundant 380 415V 20A 3 phase 5 wire Intl Redundant 48VDC 10 DA 11411 World Wide Version 4 September 19 2002 3 QuickSpecs ProLiant BL20p and p Class system Standard Features Server Blade Enclosure amp Interconnects ProLiant BL p Class Provides up to a 32 to 1 server networking cable reduction per server enclosure Each interconnect switch two Interconnect Switch Option per enclosure reduces sixteen 10 100 Base T Base TX server network ports to four uplinks ports eight uplinks total Only one to all eight uplinks may be used per enclosure Two switches per kit Every BL p Cl blad The ProLiant BL p Class F GbE Interconnect Kit includes two GbE interconnect switches and two DualTSX itis k plass server blade eee fe Interconnect Modules that provide four 4 LC 1000 SX and four 4 RJ 45 10 100 TITX uplink ports per server RJ 45 patch panels enclosure The ProLiant BL p Class C GbE Interconnect Kit includes two GbE interconnect switches and two QuadT Interconnect Modules that provide four 4 RJ 45 10 100 1000 T TX T and four 4 RJ 45 10 100 T TX uplink ports per server enclosure Also included per Interconnect Switch e Two 2 RJ 45 10 100 T TX front panel ports for management or a
48. ualTSX Interconnect Modules Note Only one interconnect kit required per server blade enclosure Single Phase Redundant Power Enclosure with 4 power supplies NA JPN 239162 001 Single Phase Power Enclosure holds a maximum of 4 power supplies no need to order additional power supplies with this option kit Single Phase Redundant Power Enclosure with 4 power supplies Intl 239162 421 Single Phase Power Enclosure holds a maximum of 4 power supplies no need to order additional power supplies with this option kit 3 Phase Redundant Power Enclosure with 6 power supplies NA JPN 230769 001 3 Phase Power Enclosure holds a maximum of 4 power supplies no need to order additional power supplies with this option kit 3 Phase Redundant Power Enclosure with 6 power supplies Int l 230769 421 3 Phase Power Enclosure holds a maximum of 4 power supplies no need to order additional power supplies with this option kit Single Phase Power Enclosure empty NA JPN 231710 001 Holds up to 4 power supplies power supplies are not included in this kit Single Phase Power Enclosure empty Int l 231710 421 Holds up to 4 power supplies power supplies are not included in this kit 3 Phase Power Enclosure empty NA JPN 231709 001 Holds up to 6 power supplies power supplies are not included in this kit 3 Phase Power Enclosure empty Int l 231709 421 Holds up to 6 power supplies power supplies
Download Pdf Manuals
Related Search