Clifford 770 Automobile Alarm User Manual
Contents
1. Siren will chirp 2 times e Hit vehicle e Siren chirps 1 time if hit hard enough to activate sensor Adjust Warn away zone Press gm Siren chirps 2 times Sensor adjustment mode is entered e Hit vehicle at the desired level of impact e Sensor adjusts itself to the force of Hit e Siren chirps 1 time as confirmation of adjustment Press K to lock adjustment Press da to re enter Primary zone adjustment e Siren chirps 2 times The Science of Security e Primary zone can now be re adjusted as described in Step 4 Or press aa again to exit programming mode e The siren will chiro 3 times when sensor adjustment mode has been exited note You must wait 15 seconds for the Omnisensor to become active after arming glossary of terms Control Unit The brain of your system Usually hidden underneath the dash area of the vehicle It houses the microprocessor which mon itors your vehicle and controls all of the system s functions Input A physical connection to the system An input can be provided by a sensor pinswitch or through an existing system in the vehicle such as ignition or courtesy lights LED Blue light mounted somewhere in the vehicle It is used to indi cate the status of your system It is also used to report triggers and faults in the system or sensors UltraSecure Immobilizer A feature on the module which prevents the vehicle s engine from operating whenever the system is armed2. Power Saver in Valet Mode When the system enters Valet Mode the LED illuminates steadily If the vehicle is not used ignition is not turned on for a period of one hour while the system is in Valet Mode the LED will shut off If the system remains in Valet Mode the LED will come back on the next time the ignition is turned on and then back off programming options Programming options control what your system does during normal operation and require few or no additional parts However some may require additional installation labor Following is a list of the program settings with the factory settings in bold 20 Active arming only with the remote or passive arming au tomatic arming 30 seconds after the last door is closed Arming disarming confirmation siren chirps on or off Auto Lock on off rpm ON The doors will lock three seconds after the ignition is turned on unless a door is open RPM The doors will lock when the engine speed increases Auto Unlock on off With this feature on the doors will unlock when the ignition is turned off Passive door locking with passive arming or active door locking only when arming with the remote Passive locking The Science of Security allows the vehicle s doors to lock when the security system passively arms after the 30 second countdown This feature only works if passive arming has been programmed Panic mode enabled disabled Some states ha
3. Once in programming mode press ya on the remote to begin playback of the available sounds Press J on the PlainView 2 Valet button while playing the desired sound to add that sound press while playing the desired sound to delete that sound diagnostics The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it It detects any faulty switches and sensors and prevents them from dis abling the entire system The microprocessor will also record and report any triggers that occurred during your absence arming diagnostics If the system is armed while an input is active door open sensor trig gering etc the unit will chirp twice when arming and then four more times five seconds later This is called Bypass Notification The security system will ignore the input that was active when the sys tem was armed until the input goes away Three seconds later the sys tem will monitor that input normally For example if your vehicle has 16 The Science of Security interior light exit delay and you arm the system before the interior light goes out you may hear Bypass Notification chirps Once the light shuts off however the doors are monitored normally disarming diagnostics Extra disarm chirps are the Tamper Alert If three chirps are heard when disarming the system was triggered in your absence If three chirps are heard the LED status indicator
4. The vehicle is never prevented from running when the system is disarmed in Valet mode or loss of power 2006 directed electronics 39 Omnisensor A dual zone learning impact sensor PlainView 2 Valet Button A small two button switch mounted some where inside the vehicle It is used to override the alarm when a remote is lost or damaged or to enter or exit Valet mode Siren Noise generating device usually installed in the engine compart ment of the vehicle It is responsible for generating the chirps you hear as well as the six tones you hear while the alarm is triggered Remote Hand held transmitter which operates the various functions of your system Trigger or Triggered Sequence This is what happens when the alarm goes off or trips The triggered response of your system consists of the siren sounding and parking light flashing for the programmed duration Warning Zone Response Lighter impacts or movement close to the vehi cle will generate the Warning Zone response It consists of a warning siren blast or beep Zone A zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone Two or more inputs often share the same zone 4A N seee o aeea security amp convenience expansions l Here we have listed only some of the many expansion options available Please contact your dealer for a complete list of all the options available to you Backup Batt
5. Turn the ignition on and enter the system valet PIN code one time valet feature This feature allows the system to be put in valet mode only until the next time the ignition is turned on ON Valet mode will be exited every time the ignition is turned on OFF Valet mode will only be exited by using the valet button or the remote control blackjax feature ee Clifford s exclusive BlackJax feature provides a safe and effective means of recovering your vehicle after a carjacking by monitoring the door input brakes and engine speed Simply get out of the vehicle and let the thief drive away After the vehicle is at a safe distance BlackJax will activate the siren and brake lights to draw attention to the vehicle When BlackJax sees the vehicle slow down or stop the UltraSecure Immobilizer circuit shuts off 2006 directed electronics 33 the engine stranding the thief and vehicle At this time your remote will not operate the system only you can turn off the BlackJax by enter ing your secret PIN through the PlainView 2 valet button blackjax activation sequence When BlackJax is programmed ON BlackJax sequence will begin every time the ignition is turned on and must be turned off by entering your PIN code It will then activate again while driving when triggered as described below 34 note BlackJax can be turned off by entering PIN code at any time Ignition on e System sees the ignition on Door open
6. doors will lock if the ignition is off the doors will unlock To stop Panic Mode at any time press aa on the remote again disarm valet mode Entering your pin code using the PlainView 2 Valet button allows you to disarm the system or enter valet mode without using the remote In valet mode the security system will not arm even with the remote but all convenience functions door locks trunk release etc will con tinue to work normally To disarm or enter Valet Mode 12 The Science of Security 1 Turn the ignition on 2 Enter PIN code factory setting is 2 Dd hess aj o No 9 WW After the last digit of the pin code is entered a To disarm the system press and release b To enter valet mode Press and hold for three seconds The LED status indicator will light steadily if you are entering Valet Mode and will turn off if you are exiting Valet Mode To exit Valet Mode 1 Turn the ignition on 29 2 Enter PIN code No D 3 After the last digit press for one second git press The LED will turn off remote valet mode The operations described in this section refer to remote buttons Remember the buttons used in all the instructions in this guide corre spond to a Standard Configuration remote This may not be how your remote is set up To enter Valet Mode press CLIFFORD twice and then gVQ The LED status indicator will light solid if you are enter
7. electronics 35 Bypass BlackJax temporarily 1 2 3 4 5 Turn ignition on Enter PIN code Do not enter valet or programming mode Within 10 seconds press pf VQ Siren chirps 1 time as confirmation of BlackJax bypassed Turn Ignition Off siren chirps 3 times as confirmation of exiting programming note If ignition remains on after entering PIN code and no action for 10 seconds unit will automatically exit programming mode without chirps To return to normal BlackJax Operation 1 2 3 4 5 Turn ignition on Enter Pin code Within 10 seconds press pf VQ Siren chirps 2 times as confirmation of BlackJax active Turn ignition off siren chirps 3 times as confirmation of exit ing programming note If ignition remains on after entering PIN code and no action for 10 seconds unit will automatically exit programming mode without chirps blackjax off warning indicator Each time the ignition is turned off when BlackJax is bypassed the LED will blink 10 times as warning that the BlackJax has been temporarily bypassed 36 The Science of Security audio sensor The 506T Audio Sensor is a low current device that provides an added level of protection to an existing security system by detecting sounds that have the acoustic signature of breaking glass or metal to glass impacts adjusting the omnisensor The Omnisensor is designed for ease of adjustment by the user and to give the ultimate in impact dete
8. will indicate which zone was involved when you turn the ignition on see the Table of Zones section The sys tem will retain this information in its memory Refer to the Multiple Fvent Total Recall section of this guide arm disarm diagnostic chart Action Chirps Light Flashes Description Arm 2 2 System armed Arm 4 4 System armed with hood trunk active and bypassed zones 5 and 6 Arm 2 5 sec 4 2 5 sec 4 System armed with door active and bypassed zone 4 Arm 2 10 sec 4 2 10 sec 4 System armed with sensor active and bypassed zones 1 2 3 and 8 Disarm 1 1 System disarmed Disarm 3 3 System disarmed with tamper alert 2006 directed electronics 17 table of zones The zone number is the number of LED flashes used by the system to identity a specific input The standard input assignments are listed below along with spaces to write in any optional sensors or switches you have had installed If the Warning Zone response is triggered the LED will not report it Zone Number Dealer Installed of LED Flashes Description Options 1 Proximity sensor 2 Omnisensor 3 Mux 1 trigger for optional Blue sensors Door switch trigger Instant trigger trunk Instant trigger hood Ignition trigger o N DD Ww A Mux 2 trigger for optional Orange sensors BlackJax activation Oo 0 Power interrupt anti code grabbing ACG This unit features Anti Code Grabbing ACG with Random Code Encryption Thi
9. 032 1 Press and release once and E once You will hear one chirp Press and release a once You will not hear a chirp after programming a zero Press and release three times and then press a once You will hear three chirps Press and release EJ two times and then press LJ once You will hear two chirps 2006 directed electronics 31 PIN Code Confirmation Procedure Begin this procedure within 15 seconds of finishing the programming sequence or the new code will not be set 1 Turn on the ignition 2 Enter the new PIN code 3 Press and hold LJ for three seconds e LED turns on New PIN code is learned and program ming is complete e LED stays off New PIN code is not learned and the sys tem reverts to the old PIN code Redo the programming sequence auto Immobilization feature s s Auto immobilization is a feature designed for maximum security it activates the UltraSecure Immobilization circuitry automatically auto immobilization sequence 1 Turn ignition off or disarm alarm 2 After 30 seconds the systems Immobilization circuits activate and engage the starter and ignition interrupt 3 LED blinks at Y2 normal speed The Science of Security 32 CLIFFORD Disarming auto immobilization To disarm auto immobilization when active follow any of the sequences listed below e Turn ignition on and press the arm disarm button e Arm the alarm and then disarm the alarm e
10. CLIFFORD Intellguard 770 eee Owner s Guide limited lifetime consumer warranty Directed Electronics Directed promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit hereafter the unit excluding without limitation the siren the remote transmitters the associated sensors and accessories which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met the unit was professionally installed and serviced by an authorized Directed dealer the unit will be professionally reinstalled in the vehi cle in which it was originally installed by an authorized Directed dealer and the unit is returned to Directed shipping prepaid with a legible copy of the bill of sale or other dated proof of pur chase bearing the following information consumer s name telephone number and address the authorized dealers name telephone number and address complete product description including accessories the year make and model of the vehicle vehicle license number and vehicle identification number All components other than the unit including without limitation the siren the remote transmitters and the associated sensors and accessories carry a one year warranty from the date of purchase of the same This warranty is non transferable and is auto matically void if the original purchaser has not completed the warran
11. CLIFFORD ES limited lifetime consumer warran Ol od ore oles ee eee ees i trademarks and copyrights li what is included 2 important information 2 system maintenance 3 your warranty Es eur fs 3 fcc id notice Es rimes eet 3 replacement remote controls 4 remote configurations 5 remote functions 6 Standard configuration 6 using your system 8 UUM RS a Ad oh ea 8 DISAIS ode este ss rs 9 disarming without a remote 10 remote siren silencing 10 remote chirp muting 10 remote sensor disable 11 intellistart and smartwindows sensor bypass suas ee ls ee us 11 auxiliary channel bypass 12 panic mode with smart door IGCRIMO SES LE Shee Gea aac 12 disarm valet mode 12 remote valet mode 13 one time auto arming bypass 14 low battery warning 14 multiple event total recall 14 false alarm control technology RACHID a wees See oe 15 select siren sounds 16 diagnostics n nonan 16 arming diagnostics 16 2006 directed electronics disarming diagnostics 17 arm disarm diagnostic chart 17 table of zones 18 anti code grabbing ACG 18 high frequency 19 smart power up Il 19 power saver mode 19 programming options 20 cliffnet wizard installation soft ware programming 22 manual programm
12. Off The doors will not automatically unlock when the igni tion is turned off e ignition The doors will automatically unlock as soon as the ignition is turned off auto passive arm and lock off on Off The doors will not lock when the system passively arms e On The doors will lock when the system passively arms This feature only applies when passive arming is programmed on siren duration 30 60 90 e The system will sound the alarm for the programmed dura tion 30 60 90 seconds during an alarm trigger or when the system is put into panic mode second unlock off on e Off Second unlock output is pulsed at the same time as the unlock output when the system is disarmed On Second unlock output is active when the arm disarm button is pressed within 10 seconds of disarming the system note The second unlock can be installed by your dealer Please note that extra parts and labor may be required 6 The Science of Security user selectable features descriptions column two set pin code This feature allows the setting of the user s personal PIN code For more information please refer to the PIN Programming section of this guide select siren sounds The individual sounds the siren produces during an full trigger alarm can be customized for owner recognition of an alarm trigger For more infor mation please refer to the Select Siren Sounds section of this guide fact Il off on Off Th
13. SOEVER INCLUDING WITHOUT LIMITATION LIABILITY FOR THEFT DAMAGE AND OR VANDALISM THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALI FORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOV ERN THE DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE UNIT DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECONOMIC 2006 directed electronics i OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages This warranty gives you specif ic legal rights and you may also have other rights that vary from State to State This product may be covered by a Guaranteed Protection Plan GPP See your authorized Directed dealer for details of the plan or call Directed Customer Service at 1 800 876 0800 Directed securi
14. and close System sees the door open and close Press and release brake pedal a System sees the brake pedal pressed b System then begins monitoring the engine speed c System sees the engine speed at two times idle BlackJax begins 20 second countdown After a 20 second countdown 5 siren chirps as reminder to enter PIN code b Brake light output pulses to flash brake lights c You then have 20 more seconds to enter PIN to turn off Blackjax The Science of Security 5 If PIN code is NOT entered within 20 seconds System sounds siren and begins flashing parking lights e Brake lights continue to flash e The system will now immobilize as described in steps 6 7 6 If system sees the engine speed return to 1 2 times idle or lower the system will immobilize the vehicle as described in step 7 7 Vehicle Immobilization e Immobilizer will engage the starter and ignition circuits e The siren will continue to sound and the parking and brake lights will flash for a maximum of 5 minutes e Immobilization circuits will remain active until correct PIN code is entered blackjax deactivation sequence To deactivate BlackJax turn the key on and then enter the PIN code at any time bypass blackjax temporarily This feature allows you to easily bypass BlackJax activation when another person drives your vehicle that should not know your PIN code IE valet parking auto service department 2006 directed
15. button Button Remote start is controlled by this button optional accessory k K Button Silent arm and disarm is controlled by this button CLIFFORD Button then f Q Button Accessory B output is controlled by these buttons CLIFFORD Button then Button These buttons activate SmartWindows 6 The Science of Security CLIFFORD Button then XK XK Button Accessory C output is controlled by these buttons CLIFFORD Button twice then f Q Button These buttons active remote Valet CLIFFORD Button twice then Button These buttons disable the sensors CLIFFORD Button three times then X Button These buttons adjust the dual zone radar sensor CLIFFORD Button twice then XK 3 Button These buttons enter safe start mode for manual transmission vehicles and activate Autostart mode CLIFFORD Button three times then X Button These buttons adjust the dual zone omnisensor 2006 directed electronics 7 using your system The buttons used in the instructions in this manual correspond to the standard remote configuration If your remote has been custom con figured the icons on your remote buttons may not correspond to the indicated functions arming You can activate or arm the system by pressing aa on your remote for one second When the system arms you will hear two short siren sounds or chirps and see the parking lights flash twice The LED will begin to flash steadily If the ve
16. clicking with a mouse This eliminates the need for pro gramming grids and lengthy programming sequences For a complete guide to system programming using the Cliffnet Wizard refer to the Cliffnet Wizard help menu manual programming instructions Be sure to document changes by taking note of all feature changes made in programming mode To enter the User Selectable Features programming 1 Ignition on Turn the ignition to the run position or start the engine 2 Enter PIN Enter the factory preset PIN code 2 by pressing on the PlainView 2 Valet button twice then once note If the factory preset PIN has been changed the new PIN must be entered 3 Hold Chirp Release After entering the PIN code press and hold until a chirp is heard and the LED turns on then release the button You have now entered the feature selec tion position of the User Selectable Features grid 4 Column select Press C the same number of times as the desired column After a pause the siren will chirp the same number of times as the selected column for confirmation The Science of Security gt gt CLIFFORD Feature select Press the same number of times as the desired feature The siren will chirp with each press The fea ture can now be changed using the remote control Feature change Press aa on the remote If the system chirps once the feature has just turned off if the system chips twice the feature has just turned on If t
17. ction without the possibility of false triggers that are common with less sophisticated sensor While adjusting this sensor it is required that you strike the vehicle with the amount force that is desired for the system to trigger note DO NOT strike window glass or flat sheet metal panels that can dent easily It is recommended that you only strike the metal pillars between the windows they are structurally sound enough not to dent ONLY strike the pillars using the heel of your hand it is more than suf ficient for the sensor distinguish as a theft attempt 1 Disarm system 2 Transmit Channel 15 Press CLIFFORD 3 times then 3K 3K 1 time e The LED will turn on and the siren will chirp 1 time Sensor test and adjustment mode is entered 3 To test Primary full trigger zone e Press ofthe remote control Siren will chirp 2 times e Hit vehicle Siren chirps 1 time if hit hard enough to activate sensor 2006 directed electronics 37 38 Adjust Primary zone e Press 6 of the remote control e Siren chirps 2 times Sensor adjustment mode is entered e Hit vehicle at the desired level of impact e Sensor adjusts itself to the force of Hit e Siren chirps 1 time as confirmation of adjustment Press of the remote control to lock adjustment To enter Warn away zone adjustment Press 3K K Siren chirps 1 time e Warn away zone adjustment is entered To test Warn away zone e Press 3K
18. cts will trigger the Warning Zone signal When triggered the siren will sound for a few seconds e Heavy impacts will trigger the system The triggered sequence is 30 60 or 90 seconds of constant siren sound ing and flashing parking lights e Ifa protected entry door hood or trunk is opened the sys tem will immediately trigger the siren and flash the parking lights If any vehicle glass is broken the system will immedi ately trigger the siren and flash the lights disarming To disarm the system press d a You will hear a chirp and the park ing lights will flash once If the power locks are connected to the sys tem the doors will unlock If the siren chirps three times when disarm ing refer to the Diagnostics section of this guide This is called Tamper Alert If the siren is active when the system is disarmed you will hear two chirps but the system is not disarmed Refer to the Remote Siren Silencing section of this guide However if the alarm completes the full trigger cycle when disarmed you will hear three chirps 2006 directed electronics 9 disarming without a remote This feature allows you to disarm the system without the remote should it be lost damaged or disabled In order to disarm without a remote you must have the vehicle s ignition key know where the PlainView 2 Valet button is located and have the PIN code Be sure to check with the installer for the location of the PlainView 2 Valet button Plea
19. e Intellistart remote start system window control e This feature is only available with SmartWindows connected e The remote channel programmed into this feature will activate the vent or roll down feature of the SmartWindows system accessory C output The remote channel programmed into this feature will activate the accessory output clear all remotes e This feature will erase all remote codes from the system memory This feature is convenient for erasing any remotes that have been lost stolen or incorrectly programmed into the system e After entering this feature press any button on the remote the siren will chirp to indicate that all remotes have been erased from memory E m CLIFFORD amp The Science of Security pin programming A PIN code can have one to four digits each digit can be from 0 9 note A PIN code cannot begin with a zero Programming Procedure 1 2 3 Enter the feature location in the installer programming grid Immediately press and release a of the PlainView 2 Valet button Select each digit by pressing 1 9 times and then press L to enter the number into the system To enter a zero press E only Wait for two siren chirps after a five second pause or five seconds after the last digit has been entered if using less than four digit code number Turn off the ignition the siren will chirp three times The programming mode is now exited To program a PIN code of 1
20. e alarm will respond to zones 1 2 3 and 8 inputs indefinitely without bypassing On The alarm will bypass for 60 minutes if zones 1 2 3 and 8 are triggered three times within a one hour period remote valet off on Off The alarm can not be put into Valet mode with the remote control On The alarm can be put into Valet mode with the remote control entry delay off on Off There is no entry delay when armed The system will trigger instantly when a door is opened On If the system has passively armed it will not trigger for 15 seconds after a door is opened allowing the user to enter the vehicle and disarm the system via the PlainView 2 Valet button 2006 directed electronics 27 reset to default settings All system settings except PIN and remote programming in the User Programming grid will be reset to their default factory setting as indi cated in bold lettering Press the arm disarm button of the TX the siren will chirp twice as confirmation panic off on e Off The panic feature is not available e On The panic feature is available auto start setting off battery only temp only battery and temp note This feature is only available with the IntelliStart option Off The vehicle will not autostart Battery The vehicle will only autostart when the car battery gets low Temperature The vehicle will only autostart at a preset low temperature e Battery and temperatu
21. e this device Directed Electronics Inc Tested to Comply C with FCC Standards 2006 directed electronics 3 replacement rem ntrol You can purchase replacement remote controls from your Authorized Dealer or on line at the following web site www directedstore com Once you receive your new remote control please refer to instruc tions included on the remote packaging remote configurations LED Indicator Arm Disarm Button Remote Start Button Trunk Release Button Silent Arm Disarm Button Clifford G5 Button Po A WIN SES note This manual describes the features and accessories that are included with your system along with information about compatible Clifford accessories that are not included For a list of included acces sories please refer to the What ls Included section of this manual 2006 directed electronics remote functions This system uses computer based code learning to learn the remote buttons This makes it possible to assign any remote button to any sys tem function The remote initially comes programmed with standard configuration but may also be customized using the CliffNet Wizard PC program The buttons in all of the instructions in this manual corre spond to a standard configuration remote standard configuration aA Button The arming disarming and panic function are controlled by this but ton da Button The trunk release or accessory output A is controlled by this
22. ery The 520T keeps the system armed triggers the alarm and keeps the immobilization circuits active if main battery power is disconnected Power Trunk Release The g button can operate a factory power release for the vehicles trunk or hatch An optional relay may be required If the factory release is not power activated the Directed s 522T trunk release solenoid can often be added Power Window Control Automatic power window control is provided with the SmartWindows system Proximity Sensor This is a sensor mounted in the vehicle that is designed to protect the interior and its contents Remote Start System For the ultimate in convenience the IntelliStart remote Start system can start your vehicle monitor engine functions and power your climate control system with a push of a button Over rev protection open hood lockout brake pedal shutoff and automatic timer shutoff are all included 2006 directed electronics 41 health check Directed Electronics recommends you return to your installing Clifford dealer to have your system checked for correct operation The first check is due one year after the installation date and at yearly intervals thereafter note There may be a small charge incurred for this service Signed Dated Signed Dated Signed Dated Signed Dated Signed Dated Signed Dated 42 CLIFFORD 2006 directed electronics 43 The company behind this system is Directed Electronic
23. he feature has more than two settings continue pressing aa on the remote to toggle through the settings You can advance to any feature in the same column by pressing within 60 seconds to program a feature in a different column begin at step 4 within 60 seconds note Refer to the Feature Descriptions sections of this guide for impor fant notes and descriptions of the system features and programming Exit programming To exit programming mode turn the igni tion off or wait 60 seconds without pressing the PlainView 2 Valet button The siren will chirp three times to indicate pro gramming mode has been exited 2006 directed electronics 23 user selectable features The factory default settings are shown in bold Add new remote Set PIN ag New remote learn autolearn default arm disarm only Auto passive Select siren New remote learn arm off on sounds accessory A channel Chirps FACT II off on New remote learn off on quiet accessory B channel 4 x GR Auto lock Remote valet New remote learn off ignition rpm off on silent mode Auto unlock Entry delay off on New remote learn off ignition remote valet Auto passive Reset to default New remote learn 6 x arm and lock except transmitter remote start off on and valet code 7 x amp amp Siren duration Panic off on New remote learn 30 60 90 window down vent Second unlock Autostart setting New remote learn off on off battery only laccessory C channel temp o
24. hicle s power door locks have been con nected to the system the doors will lock While the system is armed the LED status indicator will flash approxi mately once per second showing that the system is actively protecting your vehicle If you hear more than two chirps when arming refer to the Diagnostics section of this guide These extra chirps confirm a mal function autobypass The security system also can be programmed to arm itself automatically called passive arming If the system is programmed for passive arming it will automatically arm 30 seconds after the ignition is turned off and the system sees you leave the vehicle by opening and closing a door Whenever the system is in its 30 second passive arming countdown The siren will chirp twice and the lights will flash twice five seconds after the last door has been closed The system is not actually armed at that point The system arms and the doors lock if connected and programmed for passive locking at 30 seconds but the siren will not chirp The early chirps provide you with a 25 second warning prior to arming note If any protected entry point a door or a switch protected trunk or hood is open the system will not passively arm Additionally each time a protected entry is triggered during the arming countdown the 30 second countdown starts over When armed your vehicle is protected as follows The LED will flash as a visible theft deterrent e Light impa
25. ing Valet Mode or will turn off if you are exiting Valet Mode 2006 directed electronics 13 one time auto arming bypass This will bypass the auto arm feature once only 1 With the key turn the ignition on then off within two seconds 2 The siren will chirp once to confirm auto arming bypass 3 The system will not auto arm note The system will revert to normal auto arming when the system sees the ignition on for at least three seconds During auto arming bypass the system will not roll up the windows if SmartWindows is connected and the accessory output will not auto activate when using the remote to arm the system low battery warning When the remote battery is low the system will generate a low pitched tone when disarmed multiple event total recall This will report the last eight system triggers 1 Press and hold of the PlainView 2 Valet button 2 While still holding M arm and disarm the system then release the button 3 The LED will start to blink to indicate the most recent trigger and proceed down to the eighth trigger If fewer than eight triggers are stored in memory the LED will blink continuous ly until the system is armed disarmed using the remote or r d the ignition is turned on For more information please refer to the Table of Zones section of this guide false alarm control technology FACT II Your system offers FACT ll a feature that prevents annoying repetitive
26. ing instruc IONS eaae 54 ahr cae Sin er 22 user selectable features 24 user selectable features descrip tions column one 25 user selectable features descrip tions column two user selectable features descrip tions column three pin programming 31 auto immobilization feature 32 auto immobilization sequence 32 one time valet feature 33 blackjax feature 33 blackjax activation sequence 34 blackjax deactivation sequence35 bypass blackjax temporarily 35 blackjax off warning indicator 36 audio sensor 37 adjusting the omnisensor 37 glossary of terms 39 security amp convenience expansions 41 health check 42 what is included e Intelliguard control module and harness Two five button remotes e Presentation envelope and quick reference card e Two window decals e External antenna receiver with harness e Pre wired blue status LED e PlainView 2 Valet button e 518C neo siren e 506T audio sensor Digital dual zone omnisensor important information Congratulations on the purchase of your state of the art vehicle security system It has been designed to provide years of trouble free operation This system must be installed by an authorized dealer Installation of this product by anyone other than an authorized dealer voids the warranty As verification of authorization all authorized deal ers are pr
27. nly battery and temp BlackJax off on Clear all remotes This feature is only available with optional IntelliStart connected This feature is only available with optional SmarfWindows connected 24 CLIFFORD ES user selectable features descriptions column one add new remote auto learn Auto learn new five button remote controls to the system in the stan dard button configuration Once you have entered the feature press aa on the remote until you hear a confirmation chirp auto passive arm off on Off The remote must be used to arm the system On When the system sees the ignition turn off and the last protected entry door hood or trunk close it will begin a 30 second countdown before arming itself After the first five seconds you will hear two chirps and the lights will flash The system will arm 25 seconds later chirps off on quiet Off Chirps will not sound when arming disarming the system On Chirps will sound when arming disarming the system Quiet Chirps will sound when arming disarming the system but at a lower volume than normal auto lock off ignition rom Off The doors will not lock automatically Ignition The doors will automatically lock three seconds after the ignition is turned on unless a door is open at that time Rom The doors will lock when the system sees the engine reach a preprogrammed RPM 2006 directed electronics 25 auto unlock off ignition e
28. ovided with preprinted dealer certificates In order to maximize the use of this system please review this owner s guide carefully prior to using your system You can print additional or replacement copies of this owner s guide by accessing the Clifford web site at www clifford com The Science of Security system maintenance The system requires no specific maintenance Your remote is powered by a pair of miniature 3V lithium batteries that will last approximately one year under normal use When the battery weakens operating range will be reduced and the system will provide a low battery warn ing chirp indication when disarming your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase Your product warranty will not be validat ed if your warranty registration is not returned Make sure you receive the warranty registration from your dealer It is also necessary to keep your proof of purchase which reflects that the product was installed by an authorized dealer fcc id notice This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesirable operation Changes or modifications not expressly approved by the party responsi ble for compliance could void the user s authority to operat
29. re The vehicle will autostart with a low car battery or low temperature note Temperature and battery calibration and settings can be made only with the Cliffnet Wizard blackjax off on e Off The system cannot enter BlackJax mode On The system will enter BlackJax mode when triggered 28 The Science of Security user selectable features descriptions column three The features in this column pertain to programming individual remote chan nels in custom configurations Following is an explanation of the features arm disarm only The remote control channel programmed into this feature will arm dis arm the system only note When programming a new remote control to custom configura tion a channel must first be programmed to this feature before pro gramming the remaining channels accessory a output The remote channel programmed into this feature will activate the accessory output accessory b output The remote channel programmed into this feature will activate the accessory output silent mode The remote channel programmed into this feature will arm disarm the system but the siren will not chirp remote valet The remote channel programmed into this feature will make the system enter exit valet mode 2006 directed electronics 29 remote start e This feature is only available with IntelliStart connected e The remote channel programmed into this feature will acti vate or shut down th
30. s Since its inception Directed has had one purpose to provide consumers with the finest vehi cle security and car stereo products and accessories available The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology Directed is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world E amp OE specification is subject to change without notice Some vehicles require optional parts wiring and a few are incompatible with some features Directed is committed to delivering world class quality products and services that excite and delight our customers driven to excel LDixected ELECTRONICS Vista CA 92081 www directed com 2006 Directed Electronics All rights reserved G919621 11 06
31. s means the receiver and remotes each use a mathemati cal formula called an algorithm to change their code each time the remote is used This technology has been developed to increase the secu rity of the unit The control unit knows what the next codes should be E i CLIFFORD amp The Science of Security high frequency eee Your system transmits and receives at 433 MHz This provides a cleaner spectrum with less interference and a more stable signal smart powerup ll ees This security system will store its current state to non volatile memory If power is lost and then reconnected the system will recall the stored state from memory This means if the unit is in Valet Mode and the battery is disconnected for any reason such as servicing the car when the bat tery is reconnected the unit will still be in Valet Mode This applies to all states of the system including arm disarm and Valet Mode power saver mode Oo Your system will automatically enter Power Saver Mode while armed or in Valet Mode after a period of time in which no operation has been performed This lowers the current draw on the vehicle s battery and prevents the system from draining the battery Power Saver Mode takes over under the following conditions 2006 directed electronics 19 Power Saver when the system is armed After the system has been armed for 48 hours the LED will flash at half its nor mal rate decreasing the system s current draw
32. se refer to the Disarm Valet Mode section of this guide for instructions to enter the pin code remote siren silencing This system offers remote siren silencing Remote siren silencing is a fea ture that makes it possible to silence and reset the system when it is triggering without disarming the system If the system is triggered and the siren has been sounding press ya on the remote to stop the trigger and return the unit to the armed state The system will not dis arm but rather reset This prevents you from disabling the system should you wish to silence it without visually checking the vehicle After resetting the system press aa again to disarm the system remote chiro muting To temporarily turn off the arm or disarm chirps use remote chirp mut ing Simply press X 3 on the remote and the confirmation chirp s will be eliminated for that one operation only The parking lights will flash to confirm the arm disarm command If you want the arm disarm chirps turned off permanently please refer to the User Selectable Features section of this guide 2004 directed electronics inc TE science of security remote sensor disable To temporarily disable a sensor input arm the system press CLIFFORD twice and then The lights will flash four times and all warn away trigger zones one two three and eight are bypassed Press the buttons again the lights flash four times and both warn away and full trigger zones one t
33. trigger sequences due to a faulty sensor or environmental conditions such as thunder jackhammers airport noise etc Here s how it works The alarm triggers three times If the same sensor is triggering the alarm and the first and the third triggers are within 60 min utes of each other FACT will interpret this pattern of triggers as false alarms After the third trigger FACT II ignores or bypasses that sensor along with any other sensors sharing the same zone for 60 minutes If the bypassed sensor tries to trigger the system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that continually triggers will remain bypassed Doors are covered by FACT differently if the alarm is triggered by an open door for three full cycles the doors will be bypassed until the trig ger ceases FACT II is programmable See the Programming Options section of this guide note Arming and disarming the system does not reset this function The only way to reset a bypassed zone is for 60 minutes or to turn on the igni tion If testing your system it is important to remember that the FACT II pro gramming can cause zones to be bypassed and appear to stop working If you wish to clear the FACT Il memory turn the ignition key on 2006 directed electronics 15 select siren sounds To customize siren sounds please refer to the selectable siren sounds fea ture in the User Selectable Features grid
34. ty card and mailed it with in ten 10 days of the date of purchase to the address listed on the card the unit s date code or serial number is defaced missing or altered the unit has been modified or used in a man ner contrary to its intended purpose the unit has been damaged by accident unreasonable use neglect improper service installation or other causes not arising out of defects in materi als or construction The warranty does not cover damage to the unit caused by installation or removal of the unit Directed in its sole discretion will determine what constitutes excessive damage and may refuse the return of any unit with excessive damage TO THE MAXIMUM EXTENT ALLOWED BY LAW ALL WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY FITNESS FOR PARTICU LAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS DIRECTED SECURITY SYSTEMS INCLUDING THIS UNIT ARE DETERRENTS AGAINST POSSIBLE THEFT DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS AND HEREBY EXPRESSLY DIS CLAIMS ANY LIABILITY WHAT
35. ty systems including this unit are deterrents against possible theft Directed is not offering a guarantee or insurance against vandalism damage or theft of the automobile its parts or contents and hereby expressly disclaims any liability whatsoever including without limitation liability for theft damage and or vandalism Directed does not and has not autho rized any person or entity to create for it any other obligation promise duty or obligation in connection with this security system Make sure you have all of the following information from your dealer A clear copy of the sales receipt showing the following e Date of purchase e Your full name and address e Authorized dealer s company name and address e Type of alarm installed e Year make model and color of the automobile e Automobile license number e Vehicle identification number e All security options installed on automobile e Installation receipts important Please note that this manual was intended for US consumers and therefore includes American phrases or words trademarks and copyrights Bitwriter Clifford Code Hopping Directed Doubleguard ESP FailSafe Ghost Switch Learn Routine Nite Lite Nuisance Prevention Circuitry NPC Revenger Silent Mode Soft Chirp Stealth Coding Stinger Valet Vehicle Recovery System VRS and Warn Away are all Trademarks or Registered Trademarks of Directed Electronics Inc
36. ve laws against siren capability while driving e Full trigger response 30 60 or 90 seconds This determines how long the full triggered sequence lasts Some states have laws regulating how long a security system can sound before it is considered a nuisance False Alarm Control Technology FACT on or off Please refer to the FACT II section of this guide for a complete explanation of how FACT operates If FACT II is pro grammed off the security system will respond to inputs from any sensor indefinitely note Because many states have laws regulating security systems pro gramming FACT Il off may cause your system to violate state laws e Siren tones and chirp volume The output of the siren con sists of six different tones in sequence and the arm disarm chiro volume can be changed or eliminated Reset the system to all factory defaults Add or remove remote controls e BlackJax feature on or off e Change PIN code Custom configure the remote control Remote Valet on or off e Autostart with low battery voltage or cold temperature 2006 directed electronics 21 cliffnet wizard installation software programming Cliffnet Wizard provides access to all available system features and some that are not available when manually programming with the Valet button Cliffnet Wizard is compatible with Microsoft Windows 2000 ME XP NT so most programming operations can be accomplished by pointing and
37. wo three and eight are bypassed until the system is disarmed This can be performed anytime the system is armed 1 Arm the system 2 Press CLIFFORD twice and then 6 3 The lights will flash four times all warn away zones are now bypassed 4 Transmit the sensor bypass channel again The lights will flash four more times the sensor warn away and full trigger zones are now bypassed 6 The sensor zones will reset when disarmed intellistart and smartwindows sensor bypass When the system sees a command to start the vehicle via the Intellistart it bypasses sensor zones and will continue to bypass these zones until the remote start shuts down When the system sees a SmartWindows command for up or down operation the unit will automatically bypass sensor zones one two three and eight until the windows complete their operation 2006 directed electronics 11 note Intellistart and SmartWindows are optional Clifford accessories Ask your dealer for more details auxiliary channel bypass Alarm sensor input zones one two three and eight will be bypassed while a pulsed or timed auxiliary Output is active panic mode with smart door locking If you are threatened in or near your vehicle you can attract attention by triggering the system with your remote Just press aa for two seconds to enter Panic Mode The siren will sound and the parking lights will flash for the programmed duration If the ignition is on the
Download Pdf Manuals
Related Search