Clifford 50x Automobile Alarm User Manual
Contents
1. Clifford s exclusive FACT feature ensures you ll never experience repeated false alarms If the siren goes off DO NOT remotely disarm allow it to run for the full 30 second siren duration Before sounding the siren a second time the system automatically checks for another activated trigger or sensor to verify that a genuine intrusion is in progress Should the siren sound again you will know for sure that someone is tampering with your vehicle To disable FACT see User selectable features on pages 16 20 13 Smart AutoTesting Each time you remotely arm the system it tests all triggers and sensors If the bonnet or boot is open the system will immediately alert you with 4 chirps and 4 indicator light flashes instead of the usual 2 and 2 If a door is ajar you will receive the usual 2 chirps and 2 flashes then 5 seconds later 4 chirps and 4 flashes The door ajar warning will not work on vehicles with factory delayed or dimming courtesy lights If a sensor is malfunctioning you will receive the usual 2 chirps and 2 flashes then 10 seconds later there will be 4 chirps and 4 flashes a Specific malfunction identification If you get the 4 chirp 4 flash signal upon arming perform the following to identify the malfunctioning trigger or sensor 1 Remotely disarm then turn on the ignition The LED status indicator inside your vehicle will be flashing pause then repeat 2 Count the number of blinks in one cycle between pauses for2. Clifford Dealers and at most other electronics and automotive security shops To replace the battery any Clifford Dealer will be happy to do this for you 1 Remove the retaining screw and gently pry apart the two halves of the case with your fingernails near the bottom of the remote where the keyring is 2 Note the orientation of the old battery then replace it with the new battery and symbols are also engraved inside the bottom half of the case 3 Snap the case back together by first aligning the top where the LED window is then retightening but not over tightening the retaining screw Adding new remote controls For other drivers in your family or if you wish to control Concept 50x systems on your other cars with the same remote control you can buy additional remote controls from any Clifford Dealer call our UK office on ring on 0800 929949 or 0181 646 8440 for the nearest dealers and program them into the system yourself Each Concept 50x will respond to as many as four 12 channel ACG remote controls To add a new remote control to the system use the procedures noted in the User selectable features section on pages 16 20 How to erase the codes of lost or stolen remote controls If one of your remote controls is ever lost or stolen you may erase it from the system memory to make sure the missing remote control can never be used to disarm your system To do so use the Erase all channels feature column 1 row
3. the LED will blink 1 6 times pause then repeat the blink cycle 4 more times Count the number of blinks in one cycle and refer to the chart on page 14 to identify the trigger or sensor that was activated whilst you were away How to interpret the chirps and indicator light flashes When you use the remote the system responds with chirps and indicator light flashes Chirps and flashes Meaning 1 Your system is disarmed 2 Your system is armed 2 and then 4 Armed iii A ey A 3 Disarmed but there was an intrusion attempt whilst you were away see Smart prior intrusion attempt on page 8 4 Armed but the bonnet or boot is ajar see Smart AutoTesting on page 14 How to interpret the LED status indicator The LED on your car s dashboard or console will inform you of the system status Off System is disarmed and in normal operating mode On Valet or programming mode Flashing The Autolmmobiliser is engaged and or the system is armed and protecting your vehicle Pause between flashes Either a malfunction see page 14 or an intrusion was attempted see page 8 AutoArming If you forget to remotely arm the system will automatically arm itself 30 seconds after you park the vehicle exit and close all the doors For your convenience if you re open any door s within the 30 second countdown AutoArming will restart from the beginning once all doors are closed Concept 50x has th
4. a aoaaa aaa aaa 16 Changing the remote control battery a aoaaa aaa aa a a 18 Adding new remote controls oaa eresas ora wiare ra eeraa 18 How to erase the codes of lost or stolen remote controls aaa 18 Table of user selectable features aaa aa a a 19 20 Standard Features of the Concept 50x d Thatcham Evaluated The Concept 50x complies with the British Insurance Industry s Criteria for Vehicle Security as evaluated by Thatcham the Motor Insurance Repair Research Centre Md Lifetime Warranty For as long as you own the vehicle Clifford will repair or replace the control unit and remote controls free of charge see warranty card for full details 4d FACT False Alarm Control and Test One of many patented Clifford innovations FACT absolutely positively ends recurring false alarms Md A Pair of 4 Button 12 Channel Remote Controls For fingertip command from a distance d Anti CodeGrabbing ACG with Random Code Encryption Today s criminals are shifting from code scanning to a new much more efficient method of electronic thievery code grabbing When you use a car alarm remote control it transmits a digital code to your alarm A thief with a code grabber can record that code right off the air from hundreds of metres away then play it back when you re gone to disarm the alarm and unlock the doors Within seconds your car is just another theft statistic Fortunately Clifford s Anti Cod
5. zero chirps momentary latched 1 chirp centre Wait 3 seconds until you hear 2 chirps indicating the new code has been accepted Turn off the ignition to exit program mode you ll hear a 3 chirp confirmation 8 VERY IMPORTANT You must now test your new secret valet code Turn on the ignition enter your new code then flip the switch to its latched position The LED will illuminate If it does not the new code you programmed and the one you just entered do not match In such a case the system will revert to the previous code MON Remote controlled valet mode entry and exit You can even remotely enable or exit valet mode by transmitting channel 9 LevelShift twice then button 1 In addition to the above indications two indicator light flashes confirm remote enabling of valet mode a single flash confirms exiting The next time that the ignition switch is turned to the ON position valet mode is automatically exited 11 Keyless entry in valet mode Even if valet mode is enabled you can still remotely control the convenience features For instance press button 1 channel 1 as if you were disarming the doors will unlock confirmed by one indicator light flash and the interior lights will turn on Press button 1 again and the doors lock confirmed by two flashes You can also use the other channels to activate options such as a remote boot release or remote engine starting Sensor adjustment The two zones of your
6. 14 SmartPowerUp II If power is removed SmartPowerUp II ensures the system will automatically restore itself to its previous state when power is restored So if a thief disconnects the power whilst the system is armed and then restores it in an attempt to start the car the system will re arm and instantly sound the siren whilst immobilising the vehicle Smart Self Powered Siren with Unbreachable Digital ComLink This siren has its own built in back up battery so even if a thief cuts all the wires the siren will continue to wail Furthermore this unique Clifford designed and manufactured siren has all these important additional enhancements Unbreachable Digital ComLink Clifford s ingenious Digital ComLink is a serial communications link that ensures that if the system fuse is pulled or if power to the system is interrupted or if any siren wire is tampered with whilst the system is armed the siren will instantly activate for five minutes However if the system is disarmed and power is interrupted for authorised servicing the siren will remain silent This eliminates the need for a special separate shutoff key common to other battery backed sirens This ingenious Clifford feature guards against any possibility of a thief tampering with the system Smart charging Other battery backed sirens continually draw charging current from your vehicle s battery In time this can drain the car s battery Clifford s Smart Self Powered Siren
7. 5 on the Table of user selectable features on pages 19 20 This will clear all remote controls from the system memory Then simply program each remaining and or replacement remote control as noted in the Adding new remote controls section above Making changes to the existing security system will invalidate the certificate of installation Should any fault with the security system occur please contact your installing Clifford agent as soon as is convenient Table of user selectable features 1 chirp OFF two chirps ON Column 1 Ist latched Feature Select Column 2 Column 3 2nd latched 3rd latched Row 1 Add new remote to channel 1 Ist momentary NOTE 1 AutoLock on off AutoArming on off Row 2 Add new remote to channel 2 2nd momentary NOTE 2 AutoUnLock on off AutoArm amp Lock on off Row 3 Add new remote to channel 3 3rd momentary FACT on off NOT USED Row 4 Add new remote to channel 4 4th momentary NOTE 4 AutoActivate timed channel 4 accessory Set accessory timer duration upon remote arming on off lsec 2min 30sec this feature is for installers only NOTE 6 Row 5 Erase all channels 5th momentary NOTE 5 QuietChirps on off NOT USED Row th momentary NOT USED Long term chirp silencing on off Seta new secret valet code x WARNING If you have remote window and sunroof closure DO NOT CHANGE THIS SETTING it requires insta
8. hear two chirps and the THE SYSTEM indicator lights will flash twice The dashboard LED will flash repeatedly and the car doors will automatically lock TO DISARM Press button 1 channel 1 again One chirp and one indicator THE SYSTEM light flash confirms disarming In addition the doors will auto matically unlock and the interior lights will turn on and stay on for 30 seconds or until you start the engine whichever occurs first TO SILENTLY Press button 3 channel 3 Your Concept 50x system will arm or ARM OR DISARM disarm with all the indications noted above except for the chirp THE SYSTEM acknowledgments TO REMOTELY Button 2 channel 2 controls an electronic interlock that lets you TURN ON A TIMED separately command two functions with the same channel one ACCESSORY when the system is armed another when disarmed Pressing button 2 whilst the alarm is armed will activate the system s timed output for any duration you wish between one second and two minutes the factory setting is 30 seconds see User selectable features on pages 16 20 TO REMOTELY Button 2 channel 2 can control another function when the system OPEN THE BOOT isdisarmed such as an optional remote boot release Pressing button 2 whilst the alarm is disarmed will remotely open the boot TO ACTIVATE Button 4 channel 4 and channels 5 9 and 10 12 see How to use OTHER OPTIONS your keychain remote control on page 6 can activate a
9. only draws charging current whilst the vehicle s ignition is on i e whilst you re driving This prevents battery drain Long term chirp silencing Whenever you wish you may silence your Concept 50x s arm disarm chirps until you wish to restore them The indicator light flashes will continue to provide visual confirmation of remote controlled arming and disarming See the User selectable features section on pages 16 20 Remote controlled chirp muting This is especially valuable when parking late at night in a quiet residential area To arm or disarm silently press button 3 on your remote control instead of the usual button 1 QuietChirps You can control the volume of the arm and disarm chirps As shipped from the factory your system issues full volume chirp acknowledgments If you prefer you may reduce the chirp volume to a level that is clearly audible yet less obtrusive See the User selectable features section on pages 16 20 Automatic low battery warning If at any time the siren s back up battery voltage is low or it fails to hold its charge the normal arm and disarm chirps will be automatically muted to alert you of the problem Once the back up battery is charged the chirps will automatically be restored Noise Abatement Circuitry Automatically limits siren sounding to 2 5 minutes even if a door is left open in the wake of an intrusion attempt 15 User selectable features Your Concept 50x allows you to set many of its fea
10. to confirm the zone override This is useful when parking in an area with heavy pedestrian traffic Transmitting channel 10 again within the 10 second period will override both zones of the sensor for those times when you must leave a passenger or pet in the vehicle The sensor zones are automatically restored the next time you arm the system AufoLock and AutoUnLock For your safety and that of your passengers the doors automatically lock the instant you turn on the ignition see User selectable features on pages 16 20 When you turn the ignition off AutoUnLock automatically unlocks the doors To suit your preferences you may turn off either or both the AutoLock and or AutoUnLock features 12 Built In Two Point Autolmmobiliser Thirty seconds after you turn off the ignition the system s built in two point AutoImmobiliser electronically disengages your vehicle s starter motor and electronic fuel pump to ensure against theft of your vehicle The LED Status Indicator will repeatedly flash to indicate that AutoImmobilisation has been activated Even if a thief were to cut all the wires or even find the Concept 50x control unit and disconnect it he would still be unable to start the engine Please be aware that unlike AutoArming described above Autolmmobilisa tion occurs regardless of whether you open or close any doors What s more disabling the AutoArming feature has no effect on Autolmmobilisation When you remotely disarm your C
11. your convenience the blink cycle repeats a total of 5 times and refer to the chart below 1 blink Proximity Sensor 3 blinks Glass Tampering Sensor 4 blinks Door trigger 5 blinks Boot trigger 6 blinks Bonnet trigger 7 blinks Three incorrect consecutive valet code entries were made If your vehicle has interior light delay or dimming the system cannot provide this indication Automatic malfunction bypass The system will automatically bypass any faulty point and arm all other triggers and sensors to provide the utmost possible protection until you can have the system serviced by your local Authorised Clifford Dealer If you armed with the bonnet boot or a door open just close the open point and the system will again monitor that point Multiple event TotalRecall The system s memory records the identity of the last 8 activated or malfunctioning triggers and sensors which allows your installer to track down any malfunction To identify the triggers and sensors held in memory use the following procedure 1 With the ignition OFF flick the PlainView switch to its latched side 2 Press button 1 to arm the system then again to disarm 3 The LED will blink 1 6 times to indicate the most recently activated point pause blink 1 5 times to indicated the next most recently activated point and so on 4 Write down the number of blinks between pauses and refer to the chart above
12. Concept 50x s Proximity Sensor provides dual level protection of your vehicle If someone is lurking near your car perhaps bringing their hands and face to the window to see what is inside the outer zone of the sensor will pick up this nearby movement and trigger your Concept 50x to issue its warning tone But if a thief actually leans into the passenger compartment the sensor s interior zone will be triggered and the system will instantly blast the full alarm sound The Clifford Electronics Proximity Sensor is a radar type sensor that uses a more sophisticated more accurate and more reliable technology than that of ultrasonic type movement sensors As such the Dual Zone Proximity Sensor of your Concept 50x is impervious to normal environmental conditions such as wind and temperature variations that cause ultrasonic sensors to false alarm Your Authorised Clifford Dealer will have adjusted each of the two sensor zones at the time of installation If you find that the sensitivity setting of one or both appears to be a bit off the mark any local Authorised Clifford Dealer will be happy to make any necessary readjustments without charge Remote controlled override of one or both sensor zones Transmitting channel 10 two presses of the side LevelShift button then a press of button 2 within 10 seconds of arming the system will override the exterior warning zone of the Dual Zone Proximity Sensor When you do so you will see 4 indicator light flashes
13. World Class Auto Security Owner s Manual a PLEASE NOTE Your factory set 4 digit valet code is noted below See pages 10 11 for information on using your valet code a Ifyou wish to change your valet code to a different 4 digit number please refer to the example on page 11 Write your new valet code in the space below WARNING For security reasons do not keep this manual in your vehicle since a thief could possibly access it and learn of your secret valet code As such please keep this manual in a safe place in your home CLIFFORD World Class Auto Security Concept 50x is covered by one or more of the following Clifford Electronics U S A patents 4 158 874 4 233 642 4 327 444 4 383 242 4 430 685 4 845 464 4 887 064 4 890 108 4 922 224 4 997 053 5 081 667 5 146 215 5 157 375 5 467 070 5 650 744 and other patents pending Table of Contents Standard Features of the Concept 50x aoaaa aa aa a 2 Your 4 button 12 channel remote controls sn 6 How to use your keychain remote control a oaaae aa a a a a 6 What each button channel does sn 7 Anti CodeGrabbing ACC with Random Code Encryption 8 Smart prior intrusion attempt alert es 8 How to interpret the chirps and indicator light flashes iss 9 How to interpret the LED status indicator 2o ss 9 PUTOATINUING ETE LETT 9 AutoArming enable disable 0 2 has 9 Visual acknowledgmiuent ssri aa ve
14. an the others Buttons 2 3 and 4 are the smaller buttons to the right below and left of button 1 The LevelShift button on the side of the remote control allows you to select channels 5 12 a To transmit either channel 1 2 3 or 4 Just press either button 1 2 3 or 4 For instance to transmit channel 3 press button 3 whilst you transmit the LED indicator will blink once every second this indicates level 1 a Jo transmit either channel 5 6 7 or 8 Press the LevelShift button once This shifts buttons 1 4 to level 2 channels 5 8 Then press the desired button within the next 7 seconds For instance to transmit channel 5 press the LevelShift button once then press button 1 whilst you transmit you ll notice that the LED indicator blinks twice pauses blinks twice etc this indicates level 2 a To transmit channel 9 10 11 or 12 Press the LevelShift button twice This shifts buttons 1 4 to level 3 channels 9 12 Then press the corresponding button within the next 7 seconds For instance to transmit channel 10 press the LevelShift button twice then press button 2 whilst you transmit you ll notice that the LED blinks three times pauses blinks three times etc this indicates level 3 NOTE One second after you stop transmitting level 2 or level 3 channels 5 12 the remote control automatically returns to level 1 channels 1 4 6 What each button channel does Your Concept 50x remote controls come preprog
15. ccessories REGARDLESS OF such as the IntelliStart remote engine starter remote power ALARM STATE window control ACG Garage Door Opener Interface Concept 50x systems and accessories on your other vehicles etc WHAT ABOUT Channel 9 is used to remotely enable or exit valet mode See page CHANNEL 9 11 for more information Anti CodeGrabbing ACG with Random Code Encryption Protects you and your automobile from the most effective and onerous car stealing device ever used by car thieves a code grabber Code grabbers literally record from hundreds of metres away the code sent by your car alarm remote control Then the thief simply plays back the code when you re gone instantly disarming the alarm and unlocking the doors It s like giving the thief your car keys But not if you have the Concept 50x since it utilises complex digital signal processing and unbreachable encryption to randomly change the digital code every time you use the remote control Your remote control will never transmit the same code twice and the control unit will never accept the same code twice Thus the code recorded and played back by the thief s code grabber will never be accepted by your Concept 50x Smart prior intrusion attempt alert If you hear three chirps when you remotely disarm instead of the usual one chirp it means that a trigger or sensor was activated in your absence When you enter the vehicle and turn on the ignition or start the engine
16. d hidden valet switch In contrast your system has safeguards to ensure a thief cannot enable the valet mode as a way of turning off your system How To enable valet mode the driver must enter a secret valet code on the PlainView switch Your factory preset code is noted on the inside front cover of this manual You may whenever you wish change the code to one of your own choosing In valet mode the system s AutoArming feature see page 9 and all the security features are turned off At various times you will need to switch the system off such as when washing your car Your factory set valet code is noted on the inside front cover of this manual As Such you should NOT keep this manual in your vehicle since it could be discov ered by a thief Definitions Digit A digit is defined as any number from 0 to 9 inclusive a Valet code Your valet code is the factory preset 4 digit number noted on the inside front cover of this manual or one that you have chosen and programmed a PlainView switch A rocker switch mounted on the dashboard or console The switch has three positions 1 Latched 2 Centre 3 Spring loaded momentary When you press the latched side the switch remains in its pressed position When you press the momentary side the switch bounces back to the centre position a Entering a digit To enter a digit you tap press and release on the momentary side of the PlainView switch the number of times corr
17. e to again select column 2 Therefore you can go right away to the row selection momentary side of the switch Now within 10 seconds press the momentary side two times to jump to row 2 After a brief pause you ll hear 1 chirp to confirm that AutoUnLock is now off 4 Note that the QuietChirps feature is in the same column 2 row 5 Simply press the momentary side 5 times After a brief pause you ll hear two chirps to confirm that the QuietChirps feature is now on 5 To exit the program mode turn the ignition off You ll hear 3 chirps to confirm program mode exit continued 17 Notice that you did not have to reselect column 2 If you don t touch the switch the system stays in the column for 10 seconds to allow you to select any other feature s in the same column without having to re enter the column number Of course you may also toggle the latched side to select a new column If you wait more than 10 seconds the system automatically jumps back to the Feature Select position This is the standby position ready for entry of a new programming selection If no action is taken for the next 60 seconds the system automatically exits program mode perfect if you program whilst driving or if you forget to turn off the ignition Changing the remote control battery Your remote control is powered by a small 12 volt battery As the battery begins to go flat range will decrease Replacement batteries are available at all Authorised
18. eGrabbing ACG randomly changes the transmitted code every time you press any of the remote control buttons And since these codes are selected by the system s microprocessor from an electronic file containing several trillion codes the remote control NEVER sends the same code twice and the system control unit NEVER accepts the same code twice That makes code grabbing utterly useless against the Clifford Concept 50x Md Built In Two Point Autolmmobiliser For the utmost in theft prevention two AutoImmobilisation circuits interrupt both the starter and ignition fuel pump whilst the system is armed Even if a thief were to pull the fuses or cut all the wires the starter and ignition fuel pump remain immobilised a Failure Proof Driving Safety Even in the unlikely event of a system malfunction the AutoImmobiliser will not stop the engine whilst the vehicle is being driven Standard Features of the Concept 50x cont Md UltraSecure Coded Valet Mode Requires a code that you may select to put the system in valet mode or program in an additional remote This ensures that no thief can turn off your Concept 50x as they can with other alarms Remote Controlled Valet Mode Entry and Exit With just a press of a button on your remote control you can enter or exit valet mode Indicator light flashes visually confirm valet mode entry and exit d Dual Zone Proximity Sensor Two sensor zones provide full protection If someone is
19. ese additional AutoArming features a AutoArming enable disable If you prefer you may deactivate or reactivate the AutoArming feature See User selectable features on pages 16 20 a Visual acknowledgment Five seconds after you exit the vehicle and close all the doors the indicator lights will flash twice to confirm that the AutoArming countdown is progressing Then 25 seconds later the system will AutoArm AutoArm amp Lock To ensure you can t accidentally lock your keys inside the car the system is factory set not to lock the doors upon AutoArming To change this setting see User selectable features on pages 16 20 a Instant AutoArming bypass Prevents AutoArming when fuelling and other times when you wish to temporarily bypass AutoArming To activate Instant AutoArming Bypass rapidly turn the ignition switch to ON then OFF You will hear a single siren chirp to confirm that the system will not AutoArm The system reverts to its normal operating mode when you next start the engine 9 Ultrasecure Coded Valet Mode Your secret valet code NOTE If you temporarily lose the use of your remote controls you can disarm the system by enabling valet mode All car alarms have a valet mode that turns off the security features This mode is also used to turn off the alarm if it is not responding to the remote However thieves can disable other alarms in seconds by hotwiring the ignition and flicking the alarm s easy to fin
20. esponding to the numeral of the digit to be entered followed by pressing to the latched side then returning the switch to its centre position a Entering a code To enter your 4 digit code just repeat the above for each digit of your code If the digit is a zero you will simply move the switch to its center position then to the latched side as noted in the following example EXAMPLE To enter a code of 1203 you would move the switch thusly Momentary latched momentary momen tary latched centre latched momentary momentary momentary latched center 10 NOTE You may NOT select a code that begins with a zero The first digit of your code must be 1 9 To enable valet mode 1 Turn the ignition switch to its ON position or start the engine 2 Enter your valet code on the PlainView switch then return the switch to its centre position 3 You now have 5 seconds to press the latched position to enter valet mode The system s LED will glow continually for ongoing visual confirmation of valet mode To exit valet mode The system will automatically exit valet mode the next time that the ignition switch is turned to the ON position e g when the engine is started Be sure to return the Plain View switch to its centre neutral position Otherwise the system will automatically invoke the TotalRecall feature see page 14 Setting your own secret valet code If you wish to set your own valet code you may ch
21. ller only adjustment Changing the duration may cause damage DO NOT alter the installer only setting in the grey cell There is also an installer only column 5 so if you accidentally select an installer only feature turn off the ignition and start again NOTE 1 Transmit channel 1 or other channel of your choosing of the new remote control You will hear one chirp to confirm programming of channel 1 NOTE 2 Transmit channel 2 or other channel of your choosing of the new remote control You will hear two chirps to confirm programming of channel 2 NOTE 3 Transmit channel 3 or other channel of your choosing of the new remote control You will hear three chirps to confirm programming of channel 3 NOTE 4 Transmit channel 4 or other channel of your choosing of the new remote control You will hear four chirps to confirm programming of channel 4 NOTE 5 When you hear one chirp all remotes will have been erased from the system memory You must now add the new and or existing remote controls to the system 1 e program channels 1 4 of each remote that will be used with your Concept 50x NOTE 6 The accessory timer starts as soon as you select this feature When the duration you wish has been reached press button 1 on the remote control You will hear two chirps to confirm the new accessory timer duration 19 NOTE 7 Immediately flip the switch to its latched position then a Enter the new code that y
22. lurking near your car the system will sound a warning tone But if a thief actually leans into the passenger compartment the system will instantly blast the siren It is impervious to wind and temperature variations that cause ultrasonic sensors to false alarm id Glass Tampering Sensor Can detect attempts to break any of the vehicle s windows An optional second microphone is available for larger vehicles such as estate vehicles id Dual Mode Chirp Silencing Whenever you wish you may press a button on the remote control to arm or disarm the system silently It s perfect when parking at night in a quiet residential area Or if you prefer you may turn off the chirps on a long term basis until you wish to turn them back on 4d Remote Door Locking Unlocking with Built in Relays No more fumbling with keys in the dark or bad weather A single press of a button on the remote control simultaneously arms your system and locks the doors Another press disarms and unlocks a User Selectable AutoLock Automatically locks the doors the instant you turn on the ignition to start the engine User Selectable AutoUnLock Unlocks when you turn off the engine 4 Smart Self Powered Siren with Unbreachable Digital ComLink Continuous two way digital communication between the system and the siren assures that if at any time the system fuse is pulled or any siren wire is cut the siren will instantly activate for five minutes Yet
23. ne tL ERU 9 PAUTOATIIBCLOCK s uu s c ese der ERR E REV pu deed 9 Instant AutoArming bypass 6 i s hoa s 9 UltraSecure Coded Valet Mode saaa es 10 To enable valet mode 22 lon 11 TO Gxit valet modem 41 9 11 D e oo Ie dte UN o Io d oe de dde dS diuo A dox 11 Setting your own secret valet code 22s 11 Remote controlled valet mode entry and exit s 11 Keyless entry in valet mode oan 12 Sensor agajustrment zs um to ee ded dot dei dde vua eme qd uet 12 Remote controlled override of one or both sensor Zones 12 AutoLtock and AutoUnLoCcK s s s a do ae EERE REAL AAR Erg 12 Built In Two Point Autolmmobiliser sh 13 False Alarm Prevention and FACT False Alarm Control and Test 13 SmarEAUTOIeSTIDQ iu cm te AO BE enr do gucci Or ECTS EC 14 Automatic malfunction bypass 0 es 14 Multiple event TotalRecall oaa aa aaa sh 14 ornartPowerUDp ll 5 Se uio SA aa Gece ea AE e ede paa 15 Smart Self Powered Siren with Digital ComLink es 15 Unbreachable Digital ComLink s saos 15 Smart CA GI GIA Gs a sie oe re rmv I eve PRIV I ek a dk I eye e 15 Long term Chirp silencing san 15 Remote controlled chiro muting sn 15 QuietChirps muffled chirp sound level sn 15 Automatic low battery warning s 15 Noise abatement circuitry oos 15 User selectable features oos 16 Step by step programming instructions
24. oncept 50x the AutoImmobilisation circuits automatically disengage You then have 30 seconds to start the engine or turn the ignition switch to its ON position If more than 30 seconds pass the immobiliser will automatically reactivate This will be visually indicated by the LED repeatedly flashing To disarm the Autolmmobiliser use the remote control to arm and then disarm the system Train Drawbridge Feature Your Concept 50x has a new feature to make restarting the vehicle easier and safer after stopping for a passing train or a raised drawbridge You may need to shut down your vehicle s engine when waiting But after 30 seconds the immobilisation electronics of your Concept 50x will engage which will prevent engine starting To clear this immobilisation and to start the engine after this occurs simply do the following 1 Turn your ignition switch to the ON position 2 Press button 1 on your remote control This will both disengage the immobilisation and will automatically lock your vehicle s doors to ensure driving safety 3 You may now start the engine False Alarm Prevention and FACT False Alarm Control and Test False alarms are usually caused by a car alarm s sensor that either cannot detect the difference between normal environmental conditions and a genuine theft attempt or in the case of your Concept 50x has its sensor sensitivity set too high this can be readjusted by any Authorised Clifford Dealer
25. oose any 4 digit code except one that begins with a zero e g 3210 is fine but 0123 will not be accepted You can also change your valet code whenever you want Simply write down the 4 digit code you wish to use then refer to the example below and the User selectable features section on pages 16 20 Example Let s say you want to set a valet code of 2301 To do so you would do the following 1 From the Table of user selectable features on pages 19 and 20 you would note that the set a new secret valet code feature is in column 3 row 6 2 Enter program mode by turning on the ignition entering your current valet code then pressing the PlainView switch to its momentary side for 3 seconds until you hear a chirp 3 Select column 3 by moving the switch between latched and centre 3 times i e latched centre latched centre latched centre After a brief pause you will hear 3 chirps to confirm that you have selected feature column 3 4 Select row 6 by pressing and releasing the momentary side of the switch 6 times To help you count you will hear a chirp each time you press the momentary side Then immediately flip the switch to the latched position 5 Immediately enter your new code To enter 2301 as your new code you would press the switch in this manner momentary momentary latched you ll hear 2 chirps to confirm the first digit momentary momentary momentary latched 3 chirps to confirm the second digit centre latched
26. ou wish to use The system will sound the same number of chirps as the digit you choose when you move the switch to the latched side e g if the first digit is 4 you ll hear four chirps when you press the latched side b Make sure to return the switch to its centre position when complete c Wait 3 seconds until you hear 2 chirps indicating the new code has been accepted d Turn the ignition off You ll hear 3 chirps to confirm program mode exit and the LED will turn off e VERY IMPORTANT You must immediately test your new secret valet code Turn the ignition on enter your new code then flip the switch to its latched position The LED will illuminate If it does not the new code you programmed and the one you just entered do not match The system has reverted to the previous code 20 Copyright Clifford Electronics Inc 1997 31 161D C5xUKOM 198
27. rammed so that certain channels command certain functions The following chart indicates what each remote control channel number does and how to transmit each channel number Factory settings of the 12 remote control channels Transmittin Press the How Press g channel Causes the system to LevelShift many button number button times number 1 arm or disarm and lock or unlock the doors no 1 optionally turn on a timed device if the system is armea 2 AND no 2 optionally pop the boot if the system is disarmed 3 silently arm or disarm no 3 4 activate an optional accessory no 4 5 arm or disarm a Concept 50x on your second vehicle yes once 1 Command a Concept 50x on your second vehicle to 6 optionally turn on a timed device if the system is armea AND yes once 2 optionally unlatch the boot if the system is disarmed activate an optional accessory f controlled by a Concept 50x on your second vehicle d once 3 8 activate another optional accessory T Sne 4 controlled by a Concept 50x on your second vehicle y 9 remotely enable exit valet mode yes twice 1 10 remotely turn off one or both sensor zones yes twice 2 activate an optional accessory n controlled by a Concept 50x on your third vehicle yes Dice activate another optional accessory 12 controlled by a Concept 50x on your third vehicle yes is TO ARM Press button 1 channel 1 once You will
28. ross number and the row down number of the feature s you wish to program 2 Turn on the ignition or start the engine skip this step if the engine is running 3 Enter your valet code see page 10 then press the PlainView switch to its momentary side for 3 seconds until you hear a siren chirp the system LED will also turn on to indicate program mode You are now in the Feature Select position 4 Select the feature column Toggle the switch in and out of the latched position the same number of times as the column number of the selected feature NOTE each latched to centre motion is counted as one Pause You will hear the same number of chirps as the column number you have selected audibly confirming your selection 5 Select the feature row Press and release the momentary side the same number of times as the feature s row number You ll will hear a chirp each time you press If there is a NOTE for the selected feature perform the actions noted Pause You will hear either one or two chirps Two chirps ON one chirp OFF You may select another feature or you may exit program mode a To select another feature in that column repeat step 5 within the next 10 seconds after 10 seconds 3 chirps mean you are now back in the Feature Select position b To select a different feature column go to step 4 c To exit program mode turn the ignition off you ll hear 3 chirps and the LED will turn off If driving just wai
29. stem to automatically lock the doors every time the system AutoArms a Visual Indication Two indicator light flashes signal that the 30 second countdown to AutoArming has started a instant AutoArm Bypass Just a quick turn of the ignition switch will bypass AutoArming for one cycle perfect when fueling the vehicle AutoArming is automatically restored the next time you park d Patented Smart Prior Intrusion Attempt Alert When you return to your vehicle and remotely disarm a special chirp and indicator light flash sequence will audibly and visually alert you if an intrusion attempt was foiled whilst you were away Your Concept 50x will even identify the specific trigger or sensor that detected the intrusion attempt id Remote Controlled Courtesy Lighting For your personal safety and convenience when you remotely disarm your Concept 50x the interior lights turn on and stay on until you start the engine or 30 seconds whichever occurs first Standard Features of the Concept 50x cont Md Built In Indicator Light Flasher On board relay and circuitry will visually confirm door lock and system status ld Patented Smart AutoTesting Automatically tests all system triggers and sensors every time you remotely arm and warns you if you accidentally arm your Concept 50x system with the bonnet or boot open If there is a genuine trigger or sensor malfunction the system will specifically identify the problem thereby elimina
30. t 60 seconds for the system to automatically exit program mode OND 16 EXAMPLE 1 Turn on AutoArm amp Lock When the system AutoArms see page 9 it does not normally lock the doors to ensure that you cannot accidentally lock the keys inside the vehicle To enable this feature you ll note that AutoArm amp Lock is in column 3 row 2 of the table on pages 19 20 The off in bold type indicates the factory setting The following example will turn on AutoArm amp Lock 1 To enter program mode turn on the ignition enter your valet code as noted on page 10 then hold the switch in its momentary position until you hear a chirp 2 Select column 3 by pressing the latched side and then returning the switch to its centre position three times then wait for the three chirps to confirm column 3 To select row 2 press momentary two times you ll hear a chirp each time you press the momentary side 3 After a brief pause you ll hear two chirps to confirm that AutoArm amp Lock is now on 4 Turn the ignition off You ll hear 3 chirps confirming automatic exit from the program mode and you re done If you make an error just turn off the ignition and start again To turn AutoArm amp Lock back off just repeat steps 1 4 In step 3 you ll hear one chirps to confirm that the feature has been turned back off Remember one chirp off two chirps on NOTE You have 10 seconds to enter the row number after selecting the column If
31. ting time consuming and costly trouble shooting id Patented Malfunction AutoBypass with Automatic Monitoring In the unlikely event of a trigger or sensor malfunction Concept 50x automatically bypasses the malfunction and arms all other points to continue relentless protection of your vehicle If you simply left the bonnet boot or a door open when you armed just close it and the system will again monitor that trigger point d Multiple Event TotalRecall Concept 50x s memory stores the identity of the last eight trigger and sensor activations This provides an invaluable diagnostic means since whenever you wish the system will visually identify the activated triggers and sensors in reverse chronological order 4 Patented Remote Control Code Learning with MultiRemote Recognition Just a few flicks of a switch lets you match to the system up to 4 different 12 channel Clifford ACG remote controls Just as easily a lost or stolen remote control can be deleted d Multiple Car Control You may use the same remote to control Concept 50x systems on up to six of your other vehicles 4 High Luminescence LED Status Indicator Adds visual deterrence and identifies system status id Patented SmartPowerUp Il When power to the system is disconnected the system s nonvolatile memory always remembers the security system s last state armed or disarmed and returns to that state when power is restored So if a thief disconnects the po
32. tures to your own personal preferences via a few flicks of the PlainView switch Once you ve changed a few settings you ll find that programming Concept 50x is so easy that you can even do it whilst driving The system comes with all of its features preprogrammed as noted by the bold type in the Table of user selectable features on pages 19 20 To change any of the settings use the steps noted below To restore the feature to its factory setting just repeat the procedure How to change a user selectable feature Briefly here s how it will work e Pick a feature from the Table on pages 19 20 noting its column and row numbers e First you ll need to get into program mode by entering your secret valet code see page 10 After you have entered your code press and hold the momentary side of the PlainView switch until you hear a chirp You re now in the Feature Select position e Next you ll press the latched side of the switch a number of times identical to the column number Lastly you will press the momentary side of the switch a number of times corresponding to the row number That s all there is to it After you enter the feature s column and row numbers you ll hear either one chirp to indicate that the feature has been turned off or two chirps if turned on It s easy once you ve done it Try the examples on page 17 Step by step programming instructions 1 Refer to the Table of user selectable features and make note of the column ac
33. wer and then restores it in an attempt to start the car the system will instantly re arm 5 Your 4 button 12 channel remote controls The 4 button 12 channel remote controls are ultra sophisticated miniature radio transmitters powered by a tiny 12 volt battery A weak remote control battery will reduce range see page 18 for battery replacement instructions Electrical interference and even sunspots can interrupt the signal from your remote control to the system If this happens repeatedly press the remote control button this is more effective than holding the button The 4 button 12 channel remote control is the key to your system It has Clifford s Anti CodeGrabbing ACG technology for the ultimate protection against code grabbing devices see page 8 You will use your remote to arm and disarm the system lock and unlock the doors engage and disengage the AutoImmobilisation circuits enable exit valet mode and command options such as a remote boot release power window operation and even remote engine starting How to use your keychain remote control Your remote control can individually LED indicator poms command up to 12 different system functions and options It s like having a TV with 12 channels You change channels functions with your keychain remote control But instead of putting 12 buttons on the remote we made it easy First the button you use the most button 1 to arm disarm lock and unlock is larger th
34. when the system is disarmed and power is interrupted the siren will remain silent Automatic Low Battery Warning If the siren s back up battery voltage is low the normal arm and disarm chirps will be muted to alert you of the problem Once recharged the chirps will automatically be restored Standard Features of the Concept 50x cont 4 Smart Remote Boot Release Capability Assures that the optional remote boot release can be activated only if the system is in its disarmed state thus avoiding the possibility of falsely triggering the system This feature also ensures that the boot release cannot be remotely activated whilst driving id Remote Window Sunroof Closure Capability On certain vehicles including several models of Mercedes Benz Jaguar Volkswagen Audi and BMW the integrated timer and an optional relay can be used to automatically close the power windows and sunroof every time you remotely arm id QuietChiro Whenever you desire you may choose to lower the decibel volume of the arm and disarm chirps to a level that is clearly audible but less obtrusive than the full volume chirps All it takes is a few flicks of a switch id User Selectable AutoArming Automatically arms itself passively if you forget and has all these additional features AutoArming Enable Disable You may disable or re enable the AutoArming feature with just a few flicks of a switch a AutoArm amp Lock You may set the sy
35. you wait too long the system jumps back to the Feature Select position this is indicated with 3 chirps If you wait another 60 seconds the system will exit program mode this allows you to make programming changes even whilst you re driving In Example 2 below you ll learn how easy it is to change the settings of several different features in just one session without having to repeatedly turn the ignition on and off EXAMPLE 2 Turn off AutoLock and AutoUnLock then turn on QuietChirps This time we will change the settings of three different features in just one programming session We will turn off both the AutoLock and AutoUnLock features see page 12 as well as turn on the QuietChirps feature see page 15 Here s all you have to do 1 Enter program mode as previously noted ignition on enter your valet code then press the momentary side until you here a chirp 2 Since AutoLock is in column 2 row 1 of the Table you will have to enter the latched side twice and the momentary side once Therefore move the switch to latched centre latched centre Wait for the two chirps to confirm the selection of column 2 Within 10 seconds press and release the momentary side of the switch once you will hear a chirp when you press it After a brief pause you ll hear 1 chirp to confirm that AutoLock is now off 3 Since AutoUnLock is in column 2 row 2 and is in the same column as you just entered for AutoLock there is no need in this cas
Download Pdf Manuals
Related Search