Home
Clevo D480V Laptop User Manual
Contents
1. row 5 latched center latched center latched center wait for the 3 chirp column 3 confirmation then 5 momentary presses After a brief pause you ll hear two continued 21 chirps to confirm that the QuietChirps feature is now on 5 To exit the program mode turn the ignition off You ll hear 3 chirps to confirm program mode exit You just made three programming changes in only five steps Easy isn t it Notice again that in step 3 on the previous page you did not have to re select column 1 If you don t touch the switch the system stays in the column for 10 seconds to allow you to select any other feature s in the same column without having to re enter the column number Of course you can select a new column at any time If you wait more than 10 seconds the system automatically jumps back to the Feature Select position This is the stand by position ready for entry of a new programming selection If no action is taken for the next 60 seconds the system automatically exits program mode perfect if you program while driving or if you forget to turn off the ignition Adding new remote controls For other drivers in your family or if you wish to control IntelliGuard IQ systems on your other cars with the same remote control you can buy additional remote controls from any Clifford Dealer or call our Customer Service Department at 800 824 3208 and program them into the system yourself Each IntelliGuard 700 IQ will
2. you may at any time or place adjust and test the sensitivity of this microprocessor controlled solid state sensor The two sensor zones provide full perimeter protection If someone bumps into your car the system will sound a distinctive warning tone if forced entry is detected the full alarm will sound m Tonal Confirmation of Sensor Adjustments As you remotely increase sensitivity the confirming chirps rise in pitch Conversely as you lower each Zone s sensitivity the confirmation chirps become lower and lower in pitch m Unprecidented Reliability No moving mechanical parts to wear out and the entire electronic circuitry resides in hte passenger compartment not in the engine well where it would be exposed to temperature extremes water vibration and dirt m Adjust and Test Unobtrusively No repeated arming and disarming and no siren wailing You set and test sensitivity without activating the alarm Y Remote Override of Optional Sensor 2 A press of a button on your remote control will override optional sensor 2 for those times when you need to leave a passenger or pet in your vehicle w Remote Headlight Activation Capability Remotely turn on the headlights to illuminate your way to and from your car requires an optional relay w Remote Window Sunroof Closure Capability On several models of BMW Volkswagen Mercedes Benz and Jaguar the IntelliGuard 700 IQ s integrated timer and an optional relay can be set
3. 12 buttons on the remote control we made it easy First the button you use the most button 1 to arm disarm lock and unlock is larger than the others Buttons 2 3 and 4 are the smaller buttons to the right below and left of button 1 The LevelShift button on the side of the remote control allows you to select channels 5 12 E Jo transmit either channel 1 2 3 or 4 Just press either button 1 2 3 or 4 For instance to transmit channel 3 press button 3 While you transmit the LED indicator will blink once every second this indicates level 1 W 7o transmit either channel 5 6 7 or 8 Press the LevelShift button once This shifts buttons 1 4 to level 2 channels 5 8 Then press the desired button within the next 7 seconds For instance to transmit channel 5 press the LevelShift button once then press button 1 While you transmit you ll notice that the LED indicator blinks twice pauses blinks twice etc this indicates level 2 W 7o transmit channel 9 10 11 or 12 Press the LevelShift button twice This shifts buttons 1 4 to level 3 channels 9 12 Then press the corresponding button within the next 7 seconds For instance to transmit channel 10 press the LevelShift button twice then press button 2 While you transmit you ll notice that the LED blinks three times pauses blinks three times etc this indicates level 3 NOTE One second after you stop transmitting level 2 or level 3 channels 5 12 the remo
4. A e dh ul de ho be a 13 PIO VIS WES WTC a A ARR LM a eg 13 Entetihg adigi zo us i t s ios ote qu d o e n s s Den 13 Entering d GOdles d dapes do voa A ERE CE 13 To enable valet mode oan 13 Iloexitvaletmode ses cra we oce Ue da e A Ru 14 Setting your own secret valet code 1 o 14 Remote controlled valet mode entry and exit il 14 Keyless eniryinvalet Mode 1 s 14 Remotely adjustable Dual Zone Piezo Sensor 15 1 Table of Contents cont Remote controlled sensor adjustments ons 15 Remote controlled override of optional sensor 2 s 15 FACT False Alarm Control and Test 22s 15 Selectable starter ignition interrupt aoaaa aaa a len 16 Headlight Reminder o nn 16 AutoLock and AufoUnLock i i n 16 How to interpret the LED status indicator 0 16 Automatic Battery Saving Mode s 16 Smart Autolesting M oc a E Eee en eS 17 Specific malfunction identification 6 o 17 Automatic malfunction bypass 0 rn 17 Multiple event TotalRecall oo ns 17 Smart prior intrusion attempt alert 2r 18 High output Multisound Medallion Siren les 18 Personalized Siren Sounds 22s 18 QuietChirps muffled chirp soundlevel e 18 Long term chirp silencing onn 18 Remote controlled chiro muting oooooo occ 18 Siren d rdlion vue x e dog
5. Dodo Tuc E Aeg OR UE dou sos 18 Smart trunk release option rn 19 SrmartPowerUp 2i dep E p S XE eI RN X SU CR X xx 19 User selectable features 2n 20 Step by step programming instructions 20 EXAMPLE 1 Turn off siren sound number 2 o en 21 EXAMPLE 2 Turn off siren sound numbers 4 and then turn on QuietChirps 21 Adding new remote controls n 22 How to erase the codes of lost or stolen remote controls 22 Table of user selectable features 0 0 23 24 Standard Features of the IntelliGuard 7OO IQ W Limited Lifetime Warranty For as long as you own the vehicle Clifford Electronics will repair or replace the control unit and remote controls free of charge see the warranty card for full details W FACT False Alarm Control and Test One of many patented Clifford innovations FACT absolutely positively eliminates recurring false alarms W A Pair of 4 Button 12 Channel Remote Controls Fingertip command from a typical range of 100 feet One of the remote controls has a gun metal gray finish the other has a gorgeous laminated burlwood case W Antiscan Some car thieves still use scanners that transmit one digital code after another until they hit the one code that disarms the alarm AntiScan blocks scanners to prevent disarming by anyone other than you W Anti CodeGrabbing ACG with Random Code Encryption A code grabber is a new device that l
6. Inc 1995 31 711B IG7OM 1195 for IG700IQ owners
7. an intrusion is in progress Should the siren sound again you will know for sure that someone is tampering with your vehicle To disable FACT see User selectable features on pages 20 24 15 Selectable starter ignition interrupt At the time of installation you can select whether your IntelliGuard 700 IQ interrupts the starter line or the ignition line To verify which line is electronically interrupted enter the vehicle close the doors arm the system while inside the vehicle then try to start the engine If the engine cranks but does not start the ignition is bypassed If it does not crank at all the starter is disabled In addition the starter ignition interrupt will be set in either Fault Proof mode which lets you start the engine even in the unlikely event of a complete system failure or Super Security mode that ensures a thief won t be able to start the engine even if he cuts all the wires or finds the system control unit and disconnects it Changing the mode requires a minor relay wiring change and installer only programming Your local Authorized Clifford Dealer can make the changes for you Heaalight Reminder If you turn the ignition off and open the driver s door to exit the car without having turned off the headlights you will be reminded to turn them off with a distinctive warning tone If your vehicle already has a similar warning feature you may turn off the IntelliGuard 700 IQ Headlight Reminder feature See User se
8. normal tone chirps indicate minimum and maximum settings There are 16 sensitivity levels for each of the two sensing zones 4 Repeat steps 2 and 3 until you are satisfied with the sensitivity then press button 1 to record the new sensitivity setting and exit the sensor test adjust mode you ll hear three chirps to confirm exit You may now either repeat steps 1 4 for the other sensor zone or press button 1 again to arm the system Sound complicated It really isn t there s just a lot of explanation of what s happening with each step All you really have to do is the actions noted in bold type Give it a try Remote controlled override of optional sensor 2 If you have an optional sensor transmitting channel 10 within 10 seconds after arming the system will override the optional sensor For instance if you have an optional Proximity Sensor that picks up any movement inside the passenger compartment you may use channel 10 to turn it off for those times when you must leave your pet or a passenger in the vehicle Remote override of the optional sensor 2 is confirmed with four flashes of the parking lights FACT False Alarm Control and Test With FACT you ll never experience repeated false alarms If the MultiSound Medallion Siren goes off DO NOT remotely disarm the system allow it to run for the full siren duration Before sounding the siren a second time the system automatically checks for another activated trigger to verify that
9. precise identification of the exact trigger or sensor tripped in a prior intrusion attempt W Full Time Programming Access You can easily change the status of more than 20 different user selectable features at any time even while driving Welcome to the world of high technology vehicle security and convenience Coes on the purchase of your IntelliGuard 700 IQ vehicle security convenience system Clifford Electronics has long been recognized as the world s leading manufacturer of high technology vehicle security systems and accessories In fact Clifford Electronics holds more patents than all other vehicle security manufacturers combined Buying Clifford has always meant buying the best and nowhere is our commitment to technological innovation reliability and quality more evident than in the astounding IntelliGuard 700 IQ Your IntelliGuard 700 IQ is loaded with protective features and lifestyle convenience benefits that other car alarm companies don t even have on their wish lists let alone their alarms Features like Anti CodeGrabbing that fights off the latest and most onerous threat from high tech thieves A thief equipped with a code grabber can record with total impunity the codes of your car alarm s remote control from up to several hundred feet away How The thief simply waits for you to arm or disarm your alarm with your remote control The thief s portable pocket sized code grabber will automatically pick and rec
10. respond to as many as four 12 channel remote controls To add a new remote control to the system use the procedures noted in the User selectable features section on pages 20 24 How to erase the codes of lost or stolen remote controls If one of your remote controls is ever lost or stolen you can erase its digital codes from the system memory to make sure that the missing remote control can never be used to disarm your system To do so use the Erase all channels feature feature column 2 row 6 on the Table of user selectable features on pages 23 24 This will clear all remote control codes from the system memory Then simply program each remaining and or replacement remote control as noted in the Adding new remote controls section above 22 Table of user selectable features 1 chirp OFF two chirps ON Column 1 Column 2 Column 3 Column 4 Feature Select Ist latched 2nd latched 3rd latched Ath latched Row 1 Sound 1 on off Add new remote to channel 1 AutoLock on off AutoArming on off Ist momentary info on page 18 info on page 10 NOTE 1 info on page 16 info on page 12 Row 2 Sound 2 on off Add new remote to channel 2 AutoUnLock on off AutoArm amp Lock on off 2nd momentary info on page 18 info on page 10 NOTE 2 info on page 16 info on page 12 Row 3 Sound 3 on off Add new remote to channel 3 FACT on off 15 second entry delay on off 3rd momentary info on pa
11. the remote trunk release when you drive or when the system is armed SmartPowerUp II If power to the system is ever removed SmartPowerUp II ensures the system will automatically restore itself to its previous state when power is restored So if a thief disconnects the power and then restores it in an attempt to start the car the system will re arm and instantly sound the siren while immobilizing the vehicle If your vehicle is to be serviced by a mechanic just put the system in valet mode via the remote control see Remote controlled valet mode entry and exit on page 14 If the mechanic needs to interrupt power your system will automatically return to its valet mode state when power is restored there will be no alarm activation and no need to provide your mechanic with your remote control and instructions on how to use it 19 User selectable features Your IntelliGuard 700 IQ allows you to set many of its features to your own personal preferences Although the system s programming capabilities are very extensive we have made the programming procedures very simple to make a change you just flick the PlainView switch a few times Once you ve changed a few settings you ll find that programming IntelliGuard 700 IQ is so easy that you can even do it while driving The system comes with all of its features pre programmed as noted by the bold type in the Table of user selectable features on pages 23 24 To change any of the settings use t
12. will immediately alert you of the problem by sounding 4 chirps and 4 parking light flashes instead of the usual 2 and 2 If a door is ajar you will receive the usual 2 chirps and flashes then 5 seconds later there will be 4 chirps and 4 flashes This door ajar warning will not work on vehicles that have factory delayed courtesy lights If a sensor is malfunctioning you will receive the usual 2 chirps and 2 flashes then 10 seconds later there will be 4 chirps and 4 flashes NOTE Since this is a warning indication you will hear the 4 chirps even if you have the chirp muting feature turned on E Specific malfunction identification The system can also indicate the specific trigger or sensor that is malfunctioning If you get the 4 chirp 4 flash signal upon arming perform the following to identify the malfunctioning trigger or sensor 1 Remotely disarm then turn on the ignition The LED status indicator inside your vehicle will be flashing pause then repeat 2 Count the number of blinks in one cycle between pauses for your convenience the Number of LED blinks between pauses Sensor trigger indication 1 blink Piezo Sensor 2 blinks Optional sensor 3 blinks Door trigger 4 blinks Trunk trigger 5 blinks Hood trigger If your vehicle has a factory installed feature that turns off or dims the interior courtesy lights several seconds after you exit the vehicle the system cannot provide t
13. G with Random Code Encryption A Clifford exclusive that protects you and your automobile from the most effective and onerous car stealing device ever used by car thieves a code grabber Code grabbers are far more effective and efficient than scanning Unlike scanners that sequentially transmit one digital code after another until they hit the correct code to disarm the alarm a process that may take minutes to years depending on the system s total number of codes code grabbers literally record from hundreds of feet away the code sent by your car alarm remote control Then the thief simply plays back the code when you re gone instantly disarming the alarm and unlocking the doors It s like giving the thief your car keys Non Clifford alarms can be defeated that easily In contrast IntelliGuard IQ Series systems use complex digital signal processing and unbreachable encryption to randomly change the digital code every time you use the remote control Your remote will never transmit the same code twice and the control unit will never accept the same code twice Thus the code recorded and played back by the thief s code grabber will never be accepted by your IntelliGuard 700 IQ Only ACG can make a car alarm impervious to code grabbing and only Clifford systems have ACG with Random Code Encryption Enhanced AutoArming If this feature is enabled and you forget to remotely arm the system will automatically arm itself 30 seconds after th
14. Remember no code can have a zero E PlainView switch A rocker switch mounted on the dashboard or console The switch has three positions 1 Latched 2 Center 3 Spring loaded momentary When you press the latched side the switch remains in its pressed position When you press the momentary side the switch bounces back to the center position W Entering a digit To enter a digit you tap press and release on the momentary side of the PlainView switch the number of times corresponding to the numeral of the digit to be entered followed by pressing to the latched side then returning the switch to its center position E Entering a code If your code has only one digit enter the code as described in Entering a digit If your code has more than one digit just repeat the above for each digit of your code To enable valet mode 1 Turn the ignition switch to its ON position or start the engine 2 Enter your secret valet code on the PlainView switch then return the switch to its center position 3 You now have 5 seconds to press the latched position to enter valet mode The system s LED will glow continually for on going visual confirmation of valet mode 13 To exit valet mode 1 Turn the ignition switch to its ON position or start the engine 2 Hlick the switch back to its center position The LED will turn off to confirm that the system is now in its normal operating mode Setting your own secret valet code
15. Since all IntelliGuard IQ systems have the same factory set code it is highly advisable that you set your own valet code You may choose any 1 2 or 3 digit code that does not have any zeros You can also change your valet code whenever you want Simply write down the 1 to 3 digit code you wish to use remember no zeros in the code then refer to the User selectable features section on pages 20 24 Example Let s say you want to set your valet code to 31 To do so you would do the following 1 From the Table of User Selectable Features on pages 23 and 24 you would note that the set a new secret valet code feature is in column 4 row 6 2 Enter program mode by turning on the ignition entering your current valet code then pressing the PlainView switch to its momentary side for 3 seconds until you hear a chirp 3 Select column 4 by moving the switch between latched and center 4 times i e latched center latched center latched center latched center After a brief pause you will hear 4 chirps to confirm that you have selected feature column 4 4 Select row 6 by pressing and releasing the momentary side of the switch 6 times To help you count you will hear a chirp each time you press the momentary side 5 Immediately flip the switch to the latched position 6 Enter you new code To enter 31 as your new code you would press the switch in this manner momentary momentary momentary latched you ll hear 3 chirps to confirm
16. World Class Auto Security 700 IQ Owner s Manual CLIFFORD World Class Auto Security All IntelliGuard 1Q Series systems are covered by one or more of the following Clifford Electronics patents 4 158 874 4 233 642 4 327 444 4 383 242 4 430 685 4 845 464 4 887 064 4 890 108 4 922 224 4 997 053 5 081 667 5 146 215 5 157 375 and other patents Table of Contents Standard Features of the IntelliGuard 7OO IQ 3 Els x i hc a UD av RUE Y voe Aa DS ede 8 Your 4 button 12 channel remote controls ls 9 How to use your keychain remote control o 0 0 sn 9 To Transmit channel 1 2 38Or4 hs 9 To Transmit channel 5 6 7 Oor8 n 9 To Transmit channel 9 10 11 or 12 s 9 What each button channel does s 10 How to interpret the chirps and parking light flashes 11 ARITISCO a san fix A A ach de we A EAE he baw e CR ase 12 Anti CodeGrabbing ACC with Random Code Encryption 12 Enhanced AufoArming ooo 12 AutoArming enable disable 6 an 12 Visual acknowledgment 2 sss 12 User selectable entry delay n 12 AUTAIN A LOCK xt SIE eer sol se aet e e RU Ae 12 Instant AutoArming DyDass an 12 UltraSecure valet mode s 13 Your secret valet code aso ae ooa onn 13 Definitions i Tyr da eoe e dere d ae aei fes 13 DIG s cd A ART e E ont ER P e e Da de Ab EE ei 13 Valebcode tai uo ada ho bet rene ex e a ird e
17. button 1 channel 1 again One chirp and one parking light THE SYSTEM flash confirms disarming In addition the doors will automatically unlock and the interior lights will turn on and stay on for 30 seconds or until you start the engine whichever occurs first TO SILENTLY Press button 3 channel 3 Your IntelliGuard 700 IQ system will ARM OR DISARM arm or disarm with all the indications noted above except for the THE SYSTEM chirp acknowledgments Some vehicles require optional relays and wiring 10 TO ACTIVATE THE PANIC TO REMOTELY OPEN THE TRUNK TO ACTIVATE OTHER OPTIONS REGARDLESS OF ALARM STATE What about channels 9 122 Press button 1 for 3 seconds The lights will flash repeatedly and the siren will blare for 30 or 60 seconds user selectable or until you press button 1 again to turn it off If the ignition is on indicating you are in the car the doors will automatically lock to prevent an assailant from entering If the ignition is off the doors will unlock allowing you to enter without fumbling with your keys Button 2 channel 2 can control another function when the system is disarmed such as an optional remote trunk release Pressing button 2 while the alarm is disarmed will activate the optional remote trunk release Button 4 channel 4 and channels 5 8 see How to use your keychain remote control on page 9 can activate accessories such as remote headli
18. changing conditions all alarms require periodic fine tuning of their sensors An improperly adjusted sensor is the most common cause of false alarms With other alarms this requires repeated trips back to the dealer Not so with IntelliGuard 700 IQ You can adjust sensitivity electronically without tools and without even knowing where the sensor is mounted If the setting s of the Piezo Sensor is either too sensitive or not sensitive enough you may individually test and adjust the settings of each zone To adjust the Piezo Sensor just use the following procedure 1 Disarm the system then select the sensor zone you wish to adjust a Primary zone Transmit channel 11 LevelShift twice then button 3 b Warning zone Transmit channel 12 LevelShift twice then button 4 2 To test the current sensitivity setting a Primary zone Firmly thump the window pillar with the side of your fist You will hear a chirp to confirm activation of the primary zone b Warning zone Thump the window pillar with somewhat less force A chirp will confirm activation of the warning zone 3 If you are not satisfied with the detection level and wish to increase sensitivity press button 2 on your remote control To decrease it press button 4 Each time you increase sensitivity the siren will chirp in higher and higher pitched tones to confirm the higher sensitivity setting Conversely lower and lower tones confirm each sensitivity decrease Two
19. e vehicle doors are closed For your convenience if you re open any door s within the 30 second countdown AutoArming will restart from the beginning once all doors are closed IntelliGuard 700 IQ has these additional AutoArming features E AutoArming enable disable If you prefer you may deactivate or reactivate the AutoArming feature See User selectable features on pages 20 24 E Visual acknowledgment Five seconds after you exit the vehicle and close all the doors the parking lights will flash twice to confirm that the AutoArming countdown is progressing Then 25 seconds later the system will AutoArm E AutoArm amp Lock To ensure you can t accidentally lock your keys inside the car the system is factory set not to lock the doors upon AutoArming To change this setting see User selectable features on pages 20 24 W User selectable entry delay If you temporarily lose the use of your remote controls you may turn on the 15 second entry delay feature This allows you to enter the car and silently disarm the system by turning on the ignition within 15 seconds of opening the door See User selectable features on pages 20 24 E Instant AutoArming bypass Prevents AutoArming when fueling the vehicle and other times when you wish to temporarily bypass AutoArming To activate Instant AutoArming Bypass rapidly turn the ignition switch to ON then OFF You will hear a single siren chirp to confirm that the system will not AutoArm The sys
20. eliability All electronics of the Mult Sound Medallion Siren are built into the control unit sheltering them from the harsh underhood environment W User Selectable 30 60 Second Siren Duration m Patented Automatic Noise Abatement Automatically limits siren sounding to no more than 5 minutes even if a door is left open in the wake of an intrusion attempt W User Selectable Headlight Reminder Warns you if you forget to turn off the headlights after you park your vehicle If your vehicle already has this feature you may turn off IntelliGuard 700 IQ s Headlight Reminder W Enhanced AutoArming Automatically passively arms itself if you forget Qualifies you for a significant insurance discount ask your insurance company E AutoArming Enable Disable Enable or disable the Enhanced AutoArming features any time you wish m AutoArm amp Lock Select whether or not the doors will lock when the system automatically arms itself B 15 Second Entry Delay If you ever temporarily lose the use of your remote controls an entry delay allows you to enter the vehicle and disarm the system without sounding the siren E Visual Confirmation Two parking light flashes signal the AutoArming countdown m Instant AutoArming Bypass A quick turn of the ignition switch will bypass AutoArming for one cycle Standard Features of the IntelliGuard 7OO IQ cont Y Smart Trunk Release Capability An electronic interlock ensures
21. ets a thief record and capture off the air from a distance the digital code transmitted by your remote control whenever you arm your car When you leave the thief replays the code to disarm the alarm and unlock your car s doors ACG with Random Code Encryption makes thieves code grabbers completely useless because each time you press the button on your remote control a different random code is transmitted yet the system will flawlessly recognize and respond to your transmitter s new code and ignore all others W Full Time Remote Panic with Automatic Door Locking and Unlocking If you feel threatened you can with just a fingertip touch on your remote control sound the siren flash the parking lights and unlock your vehicle s power door locks for quick entry into your car without fumbling with your keys If you press the panic button while driving the siren will sound the lights will flash and the doors will lock to shield you from the assailant some vehicles require optional relays to control the power locks W UltraSecure Coded Valet Mode Ensures that no thief can turn off your IntelliGuard 700 IQ like they can all other alarm brands B Remote Controlled Valet Mode Enable or disable valet mode from 100 feet away The parking lights and the system LED confirm valet mode entry and exit Standard Features of the IntelliGuard 7OO IQ cont Y Remotely Adjustable Dual Zone Piezo Sensor With just a touch on the remote
22. for more information To turn off Sound 2 you ll note that Sound 2 is in column 1 row 2 of the Table on pages 23 24 The on in bold type indicates the factory setting The following example will turn that one sound off 1 To enter program mode turn on the ignition enter your valet code as noted on pages 13 14 then hold the switch in its momentary position until you hear a chirp 2 Select column 1 by pressing latched and then back to center wait for the one chirp to confirm column 1 To select row 2 press momentary twice you ll hear a chirp each time you press the momentary side 3 After a brief pause you ll hear one chirp to confirm that sound 2 is now off 4 Turn the ignition off You ll hear 3 chirps confirming automatic exit from the program mode and you re done If you make an error just turn off the ignition and start again To turn siren sound 2 back on just repeat steps 1 4 In step 3 you ll hear two chirps to confirm that siren sound 2 has been turned back on Remember one chirp off two chirps on NOTE You have 10 seconds to enter the row number after selecting the column number If you wait too long the system jumps back to the Feature Select position this is indicated with 3 chirps If you wait another 60 seconds the system will exit program mode In Example 2 below you ll learn how easy it is to change the settings of several different features in just one session without having t
23. ge 18 info on page 10 NOTE 3 info on page 15 info on page 11 Row 4 Sound 4 on off Add new remote to channel 4 pone deir dre ern ibid vids a on page td Ip ou pigs LO NOIE this feature is for installers only info on page 10 NOTE 6 Row 5 Sound 5 on off Erase all channels QuietChirps on off Siren duration 60 30 seconds 5th momentary info on page 18 info on page 22 NOTE 5 info on page 18 1 2 chirps info on page 18 Row 6 Sound 6 on off Headlight Reminder on off Long term chirp silencing on off Set a new secret valet code 6th momentary info on page 18 info on page 16 info on page 18 info on page 14 NOTE 7 WARNING If you have remote window and sunroof closure DO NOT CHANGE THIS SETTING it requires installer only adjustment Changing the duration may cause damage Please Note There is a column 5 that contains installer only features do not change any of these settings If you accidentally select column 5 turn off the ignition m NOTE 1 Transmit channel 1 or other channel of your choosing of the new m NOTE 7 Immediately flip the switch to its latched position then remote control You will hear one chirp to confirm programming of channel 1 a Enter the new code you wish to use The system will sound the same number of m NOTE 2 Transmit channel 2 or other channel of your choosing of the new chirps as the digit you choose when you move the switch to the latched side e g remote control You will hear two chirps to confirm programming of cha
24. ght activation the IntelliStart remote engine starter remote power window control electric garage door and entry gate opener s IntelliGuard IQ systems on your other vehicles etc Channels 9 through 12 control remote valet mode entry exit see page 14 remote override of optional sensor 2 see page 15 and remote adjustment of each of the two Piezo Sensor zones see page 15 How to interpret the chirps and parking light flashes When you use the remote control the system responds with chirps unless the chirp muting feature is turned on and parking light flashes These chirp flash acknowledgments mean Chirps and flashes Meaning 1 Your system is disarmed or you have remotely exited valet mode see page 14 2 Your system is armed or you have remotely engaged valet mode see page 14 9 and then4 Armed but there is a door open if there was a 5 sec delay or the sensor is malfunctioning if there was a 10 sec delay see Smart AutoTesting on page 17 3 Disarmed but there was an intrusion attempt while you were away see Smart prior intrusion attempt on page 18 4 Armed butthe hood or trunk is ajar see Smart AutoTesting on page 17 11 Antiscan Thieves can disarm some other brands of car alarms with a scanner that rapidly transmits one remote control code after another Clifford s AntiScan will detect any scanner and block the codes it generates Anti CodeGrabbing AC
25. he steps noted below To restore the feature to its factory setting just repeat the procedure How to change a user selectable feature Briefly here s how it will work You will pick a feature from the Table on pages 23 24 noting the feature s column and row numbers e First you ll need to get into program mode by entering your valet code see pages 13 14 After you have entered your valet code press the momentary side of the PlainView switch until you hear a chirp You re now in the Feature Select position e Next you ll press the latched side of the switch a number of times identical to the column number Lastly you will press the momentary side of the switch a number of times corresponding to the row number That s all there is to it After you enter the feature s column and row numbers you ll hear either one chirp to indicate that the feature has been turned off or two chirps if turned on It s easy once you ve done it Try the examples on page 21 to get the hang of it Step by step programming instructions 1 Refer to the Table of user selectable features and make note of the column across number and the row down number of the feature s you wish to program 2 Turn on the ignition or start the engine skip this step if the engine is running 3 Enter your valet code see page 13 then press the PlainView switch to its momentary side for about 3 seconds until you hear a siren chirp the system LED will also turn on
26. his indication blink cycle repeats a total of 5 times and refer to the chart below Automatic malfunction bypass To provide the utmost protection even if a system component malfunctions the system will automatically bypass any faulty point and arm all other triggers and sensors to provide the utmost possible protection until you can have the system serviced by your local Authorized Clifford Dealer If you accidentally armed with the hood trunk or a door open just close the open point and the system will again monitor that point Multiple event TotalRecall The system s memory records the identity of the last eight activated or malfunctioning triggers and sensors which allows your installer to instantly track down malfunctions To identify the triggers and sensors held in the system s memory use the following procedure 1 With the ignition OFF flick the PlainView valet switch to its latched side 2 Press button 1 to arm the system then again to disarm 17 3 The LED will blink 1 5 times to indicate the most recently activated point pause blink 1 5 times to indicate the next most recently activated point and so on 4 Write down the number of blinks between pauses and refer to the chart above Smart prior intrusion attempt alert Number of LED blinks between pauses Sensor trigger indication 1 blink Piezo Sensor 2 blinks Optional sensor 3 blinks Door trigger 4 blinks Trunk tr
27. igger 5 blinks Hood trigger If you hear three chirps when you remotely disarm it means that a trigger or sensor was activated in your absence When you enter the vehicle and turn on the ignition or start the engine the LED will blink 1 5 times pause then repeat the blink cycle 4 more times Count the number of blinks in one cycle and refer to the chart below High output Multisound Medallion Siren All the siren electronics are in the system control unit rather than the siren itself This protects them from heat dirt and exposure to the elements other alarm companies sirens are far more susceptible to failure Your IntelliGuard 700 IQ also provides these additional features W Personalized Siren Sounds Most alarm sirens have a single warble tone A few offer six tone sirens that either cannot be adjusted or require the physical destruction of certain circuit wires in order to change the sounds the change is permanent and cannot be changed again Your MultiSound Medallion Siren is different As shipped from the factory the siren sounds six different alarm sound patterns However you may turn any of the six alarm sounds on or off to create a different combination of sound patterns In all there are 64 different combinations you may select If you set your own Personalized Siren Sounds and later hear a siren at a distance you will know for sure whether it is your car or someone else s See User selectable feat
28. lectable features on pages 20 24 AutoLock and AutoUnLock For your safety and that of your passengers the doors automatically lock when you turn on the ignition to start the engine and unlock when you turn the ignition off To suit your preferences you may turn off either or both the AutoLock and or AutoUnLock features There are four possibilities AutoLock on while AutoUnLock is off or vice versa The other two combinations are both AutoLock and AutoUnLock on or both off How to interpret the LED status indicator The LED on your car s dashboard or console will inform you of the system status LED Condition Meaning Off System is disarmed and in normal operating mode i e valet mode is off On Valet mode is on the vehicle can be driven or serviced without having to disarm Flashing System is armed and protecting your vehicle Pause between flashes Either a malfunction see page 17 or an intrusion was attempted see page 18 Automatic Battery Saving Mode To conserve vehicle battery power the LED draws more current than the entire control unit if the system has remained continuously armed for 48 hours the flash rate will automatically slow to half the normal rate After 96 hours it slows to one quarter 16 Smart AutoTesting Each time you remotely arm the system it tests all triggers and sensors If the hood or trunk is open when you remotely arm the system
29. nnel 2 if the first digit is 4 you ll hear four chirps when you press the latched side m NOTE 3 Transmit channel 3 or other channel of your choosing of the new b Make sure to return the switch to its center position when complete remote control You will hear three chirps to confirm programming of channel 3 c Wait 3 seconds until you hear 2 chirps indicating the new code has been m NOTE 4 Transmit channel 4 or other channel of your choosing of the new accepted remote control You will hear four chirps to confirm programming of channel 4 d Turn the ignition off You ll hear 3 chirps to confirm program mode exit and the LED will turn off m NOTE 5 When you hear one chirp all remotes will have been erased from the system memory You must now add the new and or existing remote controls to ie ey oon Go PION ChE REIS PP a val De uses wn latched position The LED will illuminate If it does not the new code you your IntelliGuard 700 1Q programmed and the one you just entered do not match The system has m NOTE 6 The headlight timer starts as soon as you select this feature When the reverted to the previous code duration you wish has been reached press button 1 on the remote control You will hear two chirps to confirm the new headlight timer duration e VERY IMPORTANT You must immediately test your new secret valet code Turn the ignition on enter your new code then flip the switch to its 23 24 Copyright Clifford Electronics
30. o 4 different Clifford 12 channel remote controls Just as easily a lost or stolen remote control can be deleted W Multiple Car Control You may use the same remote to control up to seven different vehicles Y Control Unit with 4 Channels For remote system operation and accessories Standard Features of the IntelliGuard 7OO IQ cont W User Selectable Starter Ignition Interrupt Y ou may choose either a fault proof mode which lets you start the engine even in the unlikely event of a system failure or ultra secure mode that ensures a thief won t be able to start the vehicle even if he finds the system control unit and disconnects it W High Luminescence LED with Automatic Battery Saving Mode Adds visual deterrence and identifies system status To conserve vehicle battery power the LED draws more current than the entire control unit the LED flash rate will automatically be slowed to half it normal rate after the system has remained armed for 48 hours and a quarter its normal rate after 96 hours W SmartPowerUp I When power to the system is disconnected the system s non volatile memory always remembers the last state armed disarmed or valet mode and returns to that state when power is restored So if a thief disconnects the power and then restores it in an attempt to start the car the system will re arm and instantly sound the siren while immobilizing the vehicle w Multiple Trigger Sensor Inputs For
31. o repeatedly turn the ignition on and off EXAMPLE 2 Turn off siren sound numbers 4 and 6 then turn on QuietChirps This time we will change the settings of three different features in just one programming session We will turn off sounds 4 and 6 and turn on the QuietChirps feature see page 18 Here s all you have to do 1 Enter program mode as previously noted ignition on enter your valet code press the momentary side until you here a chirp 2 Since sound 4 is in column 1 row 4 of the Table you will have to enter the latched side once and the momentary side four times Therefore move the switch to the latched position and back to center Wait for a single chirp to confirm the selection of column 1 Within 10 seconds press and release the momentary side of the switch 4 successive times You will hear a chirp after each single press These chirps will help you count the number of presses After a brief pause you ll hear 1 chirp to confirm that sound 4 is now off 3 Since sound 6 is in column 1 row 6 and is in the same column as you just entered for sound 4 there is no need in this case to again select column 1 Therefore you can go right away to the row selection momentary side of the switch Now within 10 seconds press the momentary side six times to jump to row 6 After a brief pause you ll hear 1 chirp to confirm that sound 6 is now off 4 Now look up the location on the table of QuietChirps Note that it s in column 3
32. ord the transmitted code off the air As soon as you walk away he simply plays it back instantly disarming your alarm and unlocking the doors It s like giving the thief your car keys Code grabbing will instantly defeat all other brands of remote controlled car alarms regardless of whether they are equipped with anti scanning or trillions of digital codes IntelliGuard 700 IQ s unique PlainView Coded Valet Switch ensures that no thief or joy rider can turn off your IntelliGuard 700 IQ like they can with all other car alarm brands For total freedom from incorrectly adjusted sensors there s remote controlled adjustment of the system s dual zone Piezo Sensor that allows you to set the desired sensitivity levels any time or place with just a touch of a button on your remote control Plus there s remote controlled valet mode remote controlled override of an optional sensor an electronic inter lock to prevent accidental activation of the optional remote trunk release optional headlight activation user programmable MultiSound Medallion Siren with 64 distinctly different siren sound combinations sets your alarm apart from all others smart automatic locking unlocking if you ever panic the system full time programming access even while driving and much much more Yet despite all the sophistication the IntelliGuard 700 IQ is amazingly easy to use never more difficult than a few flicks of a switch or a press of a button on one of your miniat
33. te control automatically returns to level 1 channels 1 4 9 What each button channel does Your IntelliGuard 700 IQ remote controls come pre programmed so that certain channels command certain functions If you wish you can actually assign any channel except 9 through 12 to any function see pages 20 24 The following chart indicates what each remote control channel number does and how to transmit each channel number Transmitting Press the How Press channel Causes the system to LevelShift many button number button times number 1 arm or disarm and lock or unlock the doors no 1 2 pop the trunk if the system is disarmed no 2 3 silently arm or disarm no 3 4 activate optional accessory function 1 no 4 5 activate optional accessory function 2 yes once 1 6 activate optional accessory function 3 yes once 2 7 activate optional accessory function 4 yes once 3 8 activate optional accessory function 5 yes once 4 9 remotely enter or exit valet mode see pages 14 yes twice 1 10 remotely override optional sensor 2 see page 15 yes twice 2 T remotely eee ri Sensor s yes TT 3 12 remotely IDA Bene Sensor s yes twice 4 TO ARM Press button 1 channel 1 once You will hear two chirps and the THE SYSTEM parking lights will flash twice The dashboard LED will flash repeatedly and the car doors will automatically lock TO DISARM Press
34. tem reverts to its normal operating mode when you next start the engine 12 UltraSecure Coded Valet Mode Your secret valet code In seconds thieves can disable all other alarm brands by hotwiring the ignition and flicking an easy to find hidden valet switch Your IntelliGuard 700 has safeguards that absolutely ensure that a thief cannot enable the valet mode as a way of turning off your system How To enable valet mode the driver must first enter a secret valet code on the PlainView switch Your code will be a 1 to 3 digit number of your choosing Each digit can be any number from to 9 i e the code can be any number between 1 and 999 except those that contain a zero Whenever the system is put in valet mode it overrides the AutoArming feature see page 12 and all the security features are turned off At various times you will need to switch the system off For instance when having your car serviced washed or parked by a valet Your factory set valet code is the single digit 2 NOTE If you temporarily lose the use of your remote controls you can disarm The system by enabling valet mode Definitions W Digit A digit is defined as any number from 1 to 9 inclusive W Valet code A valet code may be 1 to 3 digits A one digit code X any number between 1 9 A two digit code XY any number between 11 99 excluding numbers with zeros A three digit code X YZ any number between 111 999 excluding numbers with zeros
35. that the optional remote trunk release can be activated only when the system is disarmed To further prevent unintentional opening of the trunk the interlock also makes sure that the trunk release cannot be remotely activated while driving Y Dual Mode Chirp Silencing Your choice of either long term chirp silencing or remote controlled chirp muting whenever you wish Y QuietChiros You may select soft or full volume arm and disarm chirp confirmations W Patented Smart AutoTesting Automatically tests all sensors and triggers every time you remotely arm the system and specifically identifies any malfunction virtually eliminating trouble shooting time Patented Malfunction AutoBypass Automatically bypasses any trigger or sensor malfunction then arms all other points to continue to provide the utmost possible protection if you simply left the hood trunk or a door open when you armed just close it and the system will again monitor that point W Eight Event TotalRecall Stores the identities of the last eight triggers and or sensors activated This provides an invaluable diagnostic means W Patented Smart Prior Intrusion Attempt Alert Warns you from a distance if an intrusion attempt was foiled while you were away And IntelliGuard 700 IQ will specifically identify which sensor or trigger was activated W Patented Remote Control Code Learning Just a few flicks of a switch lets you match to the system up t
36. the first digit momentary latched 1 chirp to confirm the second digit center Wait 3 seconds until you hear 2 chirps indicating the new code has been accepted Turn off the ignition to exit program mode you ll hear a 3 chirp confirmation 9 VERY IMPORTANT You must immediately test your new secret valet code Turn on the ignition enter your new code then flip the switch to its latched position The LED will illuminate If it does not the new code you programmed and the one you just entered do not match In such a case the system will revert to the previous code on Remote controlled valet mode entry and exit You can even enable or exit valet mode with your remote control simply by transmitting channel 9 LevelShift twice then button 1 In addition to the above indications two parking light flashes will confirm that you have remotely enabled valet mode while a single flash confirms exiting of valet mode Keyless entry in valet mode Even if valet mode is enabled you can still remotely control the convenience features For instance simply press button 1 channel 1 as if you were disarming and the doors will unlock indicated by one parking light flash and the interior lights will turn on Press button 1 again and the doors lock confirmed by two flashes You can also use the other channels to activate options such as a remote trunk release or remote engine starting 14 Remote controlled sensor adjustments Due to ever
37. to indicate program mode You are now in the Feature Select position 4 Select the feature column Toggle the switch in and out of the latched position the same number of times as the column number of the selected feature NOTE each latched to center motion is counted as one Pause You will hear the same number of chirps as the column number you have selected audibly confirming your selection 5 Select the feature row Press and release the momentary side the same number of times as the feature s row number You ll will hear a chirp each time you press If there is a NOTE for the selected feature perform the actions noted Pause You will hear either one or two chirps Two chirps ON one chirp OFF You may select another feature or you may exit program mode a To select another feature in that column repeat step 5 within the next 10 seconds after 10 seconds 3 chirps mean you are now back in the Feature Select position b To select a different feature column go to step 4 c To exit program mode turn the ignition off you ll hear 3 chirps and the LED will turn off to indicate exit of program mode If driving just wait 60 seconds and the system will automatically exit program mode 20 OND EXAMPLE 1 Turn off siren sound number 2 You can turn each of the siren s six different sound patterns on and off as you wish to create you own custom sound see the Personalized Siren Sounds section on page 18
38. to remotely close all the power windows and sunroof every time you remotely arm the system without the need for any optional modules Y Remote Controlled Door Lock Unlock Outputs A single press of remote control button 1 simultaneously arms your IntelliGuard 700 IQ and locks all the doors another press disarms and unlocks some vehicles require optional relays E User Selectable AutoLock Automatically locks the doors the doors the instant you turn on the ignition to start the engine W User Selectable AutoUnLock Automatically unlocks the doors when you turn off the engine W Deluxe Remote Keyless Entry in Valet Mode Remote door locking unlocking with parking light confirmations and interior light illumination even in valet mode 4 Standard Features of the IntelliGuard 7OO IQ cont Y Remote Courtesy Lighting Automatically turns on your vehicle s interior light s when you remotely disarm and keeps them on for 30 seconds or until you start the engine whichever occurs first W Built In Parking Light Flasher The parking lights will visually confirm alarm and doorlock status from a distance Y User Programmable Multisound Medallion Siren Designed entirely by Clifford engineers this unique siren is far superior in performance features reliability and even aesthetics to all other look alike sound alike sirens m Personalized Siren Sounds Up to 64 different siren sound combinations m Ultra R
39. ure keychain remote controls 8 Your 4 button 12 channel remote controls The 4 button 12 channel remote controls one with a gun metal gray case the other with a laminated burlwood finish are ultra sophisticated miniature radio transmitters powered by a tiny 12 volt battery Range is up to 100 feet A weak remote control battery will reduce range Electrical interference and even sunspots can interrupt the signal from your remote to the system If this happens repeatedly press the button this works better than holding the button down The 4 button 12 channel remote control is the key to your IntelliGuard 700 IQ It incorporates Clifford s Anti CodeGrabbing ACG technology for the ultimate protection against code grabbing devices see page 12 You will use your remote control to arm and disarm the system lock and unlock the doors activate the panic feature adjust sensor sensitivity enable exit valet mode override an optional sensor and command options such as a remote trunk release headlight activation power window operation electric garage door interface and even remote starting of the engine and heater or air conditioner among other options How to use your keychain remote control Your remote control can individually LED indicator command up to 12 different system functions and options It s like having a TV with 12 channels You change channels functions with your keychain remote control But instead of putting
40. ures on pages 20 24 B QuietChirps You can control the volume of the normal arm and disarm chirps As shipped from the factory your system issues full volume chirp acknowledgments If you prefer you may reduce the chirp volume to a level that is clearly audible yet less obtrusive See the User selectable features section on pages 20 24 W Long term chirp silencing Whenever you wish you may silence your IntelliGuard 700 IQ s arm and disarm chirps until you decide to restore them The parking light flashes will continue to provide visual confirmation of remote controlled arming and disarming See User selectable features on pages 20 24 18 E Remote controlled chirp muting Remote controlled chirp muting capabilities are especially valuable when parking late at night in a quiet residential area or any other time when you want to arm or disarm silently To arm or disarm silently simply press button 3 channel 3 on your remote control instead of the usual button 1 channel 1 W Siren duration When the system detects an intrusion attempt the alarm is set to sound for 30 seconds However if you prefer you may change it to 60 seconds See the User selectable features section on pages 20 24 Smart trunk release option If the remote trunk release feature was installed you may use the remote control s button 2 to remotely pop the trunk Your IntelliGuard 700 IQ has a built in electronic interlock to prevent unintentional activation of
Download Pdf Manuals
Related Search
Related Contents
Samsung Galaxy S4 mini Manual de Usuario 据付工事説明書 MCW MCWHU - Schumann GmbH JVC KD-SX740 CD Player HP D4163 User's Manual Korona Fabio 取り扱い説明書 Operating Instructions Air Conditioner Copyright © All rights reserved.
Failed to retrieve file