Chauvet ZX-30RG Indoor Furnishings User Manual
Contents
1. LARUVEI Value Innovation Performance Precision Series ZX 30RG J e User Guide Please read these instructions carefully before use World wide Headquarters 3000 North 29th Ct Hollywood Florida USA 33020 Tel 1 954 929 1115 Fax 1 954 929 5560 www ChauvetLighting com On Front Scanning Range Post Scanning Mirror e Lens On Bottom Funtion Switch f Fuse Holder Fan A ACOCSO TO INTERNAL LANE TAOCE TU GODI C REMOWE BOTTOM PLATE AOCESS T C L A On Back e Bracket Screws e Cable to Head e Dichroic Filter Holder Gobo Holder eLamp Replacement Cover Rear View Front View Congratulations on the purchase of your new CHAUVET lighting effect We are confident you will enjoy many trouble free hours with this unit To assist with the care and use of the product we have prepared this short guide Operation Before connecting this unit to the mains power supply for the first time you must first install the lamps See Replacing Lamps for details This lighting effect has been designed to function on a mains power supply of either 120V 60Hz or 230V 50Hz and has been fitted with a suitable power plug for use with your local voltage Check the label and voltage selector switch if fitted on the unit and the power plug for the correct voltage When connected to the mains power supply the unit should illuminate This effect has two modes of op2. e replacement lamp Finally before using check that the lamp is housed correctly in the lamp holder and that the lamp replacement cover has been screwed back into place If after replacement of the lamp the unit is still not working then please contact CHAUVET for servicing Replacing Fuses If the unit does not function at all when connected to the main power supply i e the mechanism does not spin Then it is highly likely that the fuse has blown Disconnect from main power supply before attempting to replace either lamps or fuse In order to replace the fuse disconnect from the main power supply first and then unscrew the fuse holder cover to reveal the fuse The unit has a label attached which indicates the correct fuse rating and you will also find this listed as part of the specifications for the unit later in this guide It is most important that replacement fuses are of the correct rating Failure to use the correct fuse could dam age the lighting effect beyond economic repair The fuse should simply be placed inside the holder and the screw cap replaced when this is done connect to the main power supply to check If the unit is still not working then please contact CHAUVET for servicing Cleaning The most important part of your lighting effect to keep clean is the lens as it allows the light output to transmit This should be cleaned with a soft damp cloth The body of the unit may also be cleaned in the same way We recom
3. er Replace the holder in the unit and screw in tightly Gobo The ZX 30RG is supplied with 4 interchangeable gobos To change insert a gobo remove the screw on the bottom of the unit securing the gobo holder Remove the gobo and replace with the desired gobo Replace the gobo holder in the ZX 30RG and secure the screw tightly The ZX 30RG will accept custom gobos The gobo has a diameter of 25 mm The image area has a diameter of 18mm Installation Mounting Although this unit can be used in an upright position it is recommended that for safety purposes your lighting effect be properly mounted using a suitable hanging clamp and safety cable CHAUVET offers a range of items which are ideal for safe mounting Replacing Lamps 1 Disconnect from main power supply before attempting to replace either lamps or fuse 2 Ensure that the unit is sufficiently cool before removing blown lamps 3 Never touch new lamps with your fingers use a tissue or a cloth In order to replace the lamp disconnect from main power supply first and unscrew the lamp replacement cover which is highlighted on the diagram fig 1 Only use the appropriately rated lamps as use of any other lamp type may cause the unit to be non operational Due to the nature of halogen lamps it is vitally important that you do not touch the new replacement lamp with your fingers as this will reduce lamp life considerably Once again a tissue or cloth can be used for fitting th
4. eration static or continuous scanning There is a selector switch at the rear which determines the mode see fig 1 Due to the high operating temperature of halogen lamps it is advisable that the effect be used in well ventilated areas taking care not to obstruct the air vents After use allow time to cool for safety and to ensure lamp life before moving or touching The duty cycle for this effect should be no more than 15 minutes on then 15 minutes off Use in a well ventilated area without obstruction to air vents or fan Features Removeable Head To use the ZX 30RG as a projector the head may be removed In order to remove the head simply unscrew the four screws holding the head bracket to the body of the unit and unplug the connecting cable Selectable Scanning Range The ZX 30RG offers the user a choice of 3 scanning ranges 180 150 or 120 degrees To select the desired scanning range simply put the set screw in the hole marked with the range required Function The ZX 30RG offers the user a choice of either static or scanning This feature is con trolled by the 2 position switch on the bottom of the unit located just above the fan This controls only the scanning mirror The gobo will always be rotating Color The ZX 30RG comes complete with 4 dichroic glass filters red green yellow and blue To insert the filter unscrew the filter holder on the bottom of the unit and slide the desired color into the hold
5. mend internal cleaning be carried out by a fully qualified technician Maintenance amp Servicing Work on internal parts should be carried out by a qualified technician Removal of covers other than the front to replace lamp or effect dish or the fuseholder is considered a breach of warranty and will not be covered under any such agreement unless authorized first by the company Troubleshooting If the unit is not functional check main power supply is on and check fuses e If the unit is functional but lamp does not light lamp may require replacing e If after trying this solution you still have a problem contact CHAUVET Contact Chauvet USA Tecnical Assistance 1 800 762 1084 954 929 1115 E Mail tech chauvetlighting com Caution Do not obstruct the air vents or fan Do not touch unit or lamps while hot Never put any objects through the air grill on the top of the unit No user serviceable parts inside please refer to CHAUVET for service Power Connections The unit is supplied with a power plug appropriate to its voltage and destination Should any other connections be required they must be carried out with the following configuration Earth Green Yellow cable Neutral Blue cable Live Brown cable In the USA amp Europe it is required that all plugs are 3 pin type i e with Earth Ground connection In the UK it is required that all mains plugs are fitted with 5A fuses Technical Specificatio
6. ns Power 110V 60 Hz or 230V 50 HZ Fuse 110V 2A 125V 220V 1A 250V Lamp 15V 150W EFR5 500 hours Dim 18 5 in x 7 inx 7 in 470 mm x 178 mm x 178 mm Weight 6 5 Ibs 2 95 kg User Information Please complete for your records Date Purchased Serial No Dealer Stamp Model Precision Series ZX 30RG
Download Pdf Manuals
Related Search