Chamberlain 3500D Garage Door Opener User Manual
Contents
1. CHAMBERLAIN LiftMaster PROFESSIONAL To prevent possible SERIOUS INJURY or DEATH from electrocution e Be sure power is NOT connected BEFORE installing the receiver To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door e ALWAYS keep remote controls out of reach of children NEVER permit children to operate or play with remote controls e Activate gate or door ONLY when it can be seen clearly is properly adjusted and there are no obstructions to door travel e ALWAYS keep gate or garage door in sight until completely closed NEVER permit anyone to cross path of moving gate or door MOUNTING RECEIVER e Unplug the opener before proceeding e Fully extend antenna wire below bottom of case as shown e The receiver can be mounted directly on the door opener with the clips provided Figure 1 OR e Attached to a ceiling inside wall of the garage with connecting bell wire not provided Fasten the receiver to the ceiling or inside garage wall with dry wall screws provided Figure 2 NOTE Transformer Model 85 or 95 is required if your residential garage door opener is a LiftMaster Chamberlain or Sears INSTALLATION USING CLIPS Loosen the three terminal screws on the receiver labeled 1 2 and 3 Figure 1 Insert one end of a mounting clip under each terminal Do not retighten at this time Loosen the three terminal screws on the opener used for push button controls and radio power2. Leaving the push button bell wire in place insert the other ends of the mounting clips under the opener terminal screws NOTE If the number sequence of opener terminals does not match the receiver turn the receiver around so back is facing out and complete the connection Retighten the terminal screws on opener and receiver Reconnect power to the opener The receiver push bar should light If it does not use Transformer Model 85 or 95 INSTALLATION USING BELL WIRE Attach one end of 3 strand bell wire not provided to receiver terminals 1 2 and 3 Connect the other end to the three opener terminals used for push button controls and radio power Use insulated staples to secure bell wire between receiver and opener Figure 2 Reconnect power to the opener The receiver push bar should light If it does not use Transformer Model 85 or 95 INSTALLATION WITH TRANSFORMER With the transformer use a 2 wire connection only Attach wire to receiver terminals 1 and 2 and to the opener terminals used for push button control Plug the transformer into receiver and 120 Volt outlet Figure 3 Universal Radio Control OWNER S MANUAL Model 355LM Security Receiver Only Model 355 2LM Security With 2 Remote Controls NOTICE TO U S CONSUMERS Some states prohibit the service or repair of garage door openers which cannot be made to comply with the safety standards contained in UL 325 1988 revision In order to comply with bot
3. h the letter and the spirit of these laws this universal radio control should not be used with any LiftMaster Chamberlain or Sears Craftsman garage door opener manufactured prior to April 1 1982 To find out if your Chamberlain made garage door opener was manufactured prior to or after April 1 1982 please call 1 800 528 9131 before installing this universal radio control Push Button Radio Power Common Opener 6 6 6 Terminals SpE U Master PROFESSIONAL Antenna Wire Fully Extended Push Button Radio Power jor Opener APE Terminals Antenna Wire Fully Extended Opener Terminals Transformer NOTE Transformer Model 85 or 95 is required if your residential garage door opener is a LiftMaster Chamberlain or Sears PROGRAMMING THE REMOTE TO THE RECEIVER With Security the code between the remote control and the receiver changes with each use accessing over 100 billion new codes You can activate your opener with up to 8 Security remote controls and one Security Keyless Entry 1 Pry open the front panel of receiver case with a coin or a screwdriver Figure 4 Re connect power to opener 2 Press and release the SMART button on the receiver The SMART indicator light will glow steadily for 30 seconds Figure 5 3 Within 30 seconds press and hold t
4. he button on the hand held remote that you wish to operate your garage door Figure 6 The opener will now operate when the push button on either the receiver or the remote control is pressed Repeat Steps 2 and 3 for each remote control that will be used to operate the garage door opener TO ERASE ALL REMOTE CONTROL CODES Press and hold the SMART button on the receiver panel until the indicator light turns off about 6 seconds All remote control codes are now erased Then follow the steps above to reprogram each remote control REPLACING THE REMOTE CONTROL BATTERY The lithium battery should produce power for up to 5 years To replace battery pry open case with visor clip or screwdriver as shown Insert battery positive side up Dispose of old battery properly SET OUTPUT DURATION COMMERCIAL APPLICATIONS ONLY WARNING To prevent possible SERIOUS INJURY or DEATH the use of CONSTANT OPERATION on residential openers is PROHIBITED For commercial applications the receiver can be set for either constant or momentary closure on the output contacts Use of constant closure is prohibited on residential garage door openers because it overrides the safety reversal devices With the jumper in the M Momentary position the contacts will close for 1 4 second regardless of the length of radio transmission With the jumper in C Constant position the contacts will stay closed as long as the radio cont
5. inues transmitting The receiver is factory set at M SPECIFICATIONS Output Rating ec eeeeeeeeeneeeeeeeneees 5 Amps 28VAC or DC Max POWGfissseseiscvastucsvveciedsssstedsredensekaccitescionss 18V 30V 30mA 60Hz 18 30V 30mA RF FreqQue ny iin ccc sccaceceeeecudeeehiedennudeeenseceeescceeenschessvenyexsete 315MHz If the power is other than shown in specifications Accessory Transformer Model 85 or 95 is required Accessory Remote Controls Series 300 Figure 4 Master e OPES SIONAL Figure 5 Indicator z Light Figure 6 N4 f To prevent possible SERIOUS INJURY or DEATH SMART Button Option Jumper e NEVER allow small children near batteries e f battery is swallowed immediately notify doctor NOTICE To comply with FCC and or Industry Canada IC rules adjustment or modifications of this receiver and or remote control are prohibited except for changing the code setting or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS Tested to Comply with FCC Standards FOR HOME OR OFFICE USE Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation MOMENTARY OPERATION Jumper yy 1 Output Duration Terminals CONSTANT OPERATION Duration Termi
6. nals FOR SERVICE DIAL OUR TOLL FREE NUMBER 1 800 528 2817 2006 The Chamberlain Group Inc 114A3099D All Rights Reserved
Download Pdf Manuals
Related Search