CFM Corporation UVDR36C Indoor Fireplace User Manual
Contents
1. 3 Remove the metal hearth cover and the bot tom two right brick panels from the fireplace and care fully place them to the side to prevent damage Step 4 Locate the blower access cutout found at the rear of the hearth pan Next remove tape backing from tape on blower housing Center the blower assembly in the access cutout area with the blower outlet duct point ing upward then press firmly to attach foam tape to the back and bottom of the fireplace Fig 10 Step 5 Locate the junction box cutout found on the right side of the hearth pan Route the powercord under the hearth pan and plug it into the receptacle outlet found in the junction box Fig 11 Step 6 Turn power back on and test blower operation Step 7 Replace the metal hearth cover and the bottom two center panels in the fireplace Blower Back Firebrick Access t Cutout inHearth Pan NOTE Hearth brick and or hearth cover is removed as shown to gain access for blower and junction box instal lation T230 Receptacle Outlet in Juc tion Box Junction Box Cutout in Hearth Pan of Firebox Fig 11 Route powercord under the hearth pan and plug into the receptacle outlet 20007469 Install Optional Outside Air Kit The AKU3 Outside Air Kit can be installed to bring com bustion air to the heated room air The air that is drawn into the heated room air from outside the home or un heated area helps relieve the pressure in the home The duct termin2. other than wood flooring it must be installed on a metal or wood panel extending its full width and depth Alternatively the carpeting vinyl tile etc may be removed from beneath the fireplace before installing COMBUSTIBLE MATERIALS MUST NOT BE INSTALLED OVER OR TOUCH ANY BLACK PAINTED SURFACE DO NOT BLOCK HEAT CIRCU LATING AIR OUTLETS DOING SO MAY RESULT IN POTENTIAL FIRE HAZARD Clearances To ensure a Safe installation the following instructions must be carefully observed 1 Sidewall Clearances Clearances from the side of the fireplace opening to any combustible wall should not be less than 5 Fig 3a 2 Ceiling Clearances The ceiling height should not be less than 42 from the top of the fireplace open ing 3 Mantel Clearances a If the fireplace has no mantelpiece then the heat resistant material must extend upwards a dis tance of at least 912 from the fireplace opening A mantel projection must be a minimum of 24 above the top fireplace opening if a canopy is not installed Fig 3b b Noncombustible materials used in this installation such as slate marble tile etc must be at least 1 2 thick Do not install a combustible material behind sheet metal Failure to use noncombus tible materials above the opening as specified in these instructions may cause damage to the materials used and create a fire hazard c Aheat reducing canopy is shipped with the fireplace Use of this canopy is optional i
3. 988 14 Nailing Flange Bag of 4 w Screws 2253160 2253160 20007469 11 UVDR Series Unvented Gas Fireplaces Accessories SPB42 Blower Kit BL 4 or FK12 Junction box is provided with fireplace UC42PB UVDR42C Polished Brass Brick Canopy BC36L UVDR36C BC42L UVDR42C Outside Air Kit AKU3 Contact CFM Corporation for questions concerning prices and policies covering replacement parts Parts may be ordered through your Majestic Fireplaces dis Repair and replacement work should only be done by a tributor or dealer qualified service person Always shut off the gas supply and make sure the appli You will need the correct name part number and model E i ance is cool before beginning any service operation number of the appliance when ordering replacement parts Always check for gas leaks after servicing Should you need additional information beyond what your dealer can furnish contact CFM Corporation 410 Admiral Blvd Mississauga Ontario Canada L5T 2N6 12 20007469 UVDR Series Unvented Gas Fireplaces 20007469 13 UVDR Series Unvented Gas Fireplaces 14 20007469 LIMITED LIFETIME WARRANTY PRODUCT COVERED BY THIS WARRANTY All Vermont Castings gas stoves gas inserts and gas fireplaces and all Majestic or Northern Flame brand gas fireplaces equipped with an Insta Flame Ceramic Burner or standard steel tube burner BASIC WARRANTY CFM Corporation hereinafter referred to collectively as t
4. MAJESTIC FIREPLACES INSTALLER CONSUMER SAFETY INFORMATION Read and save these instructions This book contains your installation instruc tions and should be kept in a safe place For you to realize all the advantages and use of the reliable service that has been engineered into your CFM Corporation fireplace you must carefully follow all of the instructions contained in this book regarding installation and operation of the fireplace These instructions should be read carefully in their entirety before beginning installation of the fireplace It is suggested that you wear work gloves and safety glasses to protect your hands and eyes when installing your fireplace NOTE Authorities having jurisdiction i e building inspectors fire marshals etc should be consulted before installation to determine the need to obtain a permit When installing the Blower Kit it is neces sary to bring the power source to the fire place before walls are enclosed Refer to Blower Kit instructions These fireboxes are approved as univer sal fireboxes and can be paired with any ANSI Z21 11 2 approved vent free log set The vent free log manufacturer s instruc tions including their required dimen sional clearances for firebox size must be followed Refer to the manual that is packed with the log set for operating instructions Not for use in bedroom or bathroom installa tions Ventless Fireplace Models UVDR36C
5. S OF INCIDENTAL AND CONSEQUENTIAL DAMAGES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOUR CIRCUMSTANCES THIS WARRANTY GIVES YOU SPECIFIC RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE All other warranties expressed or implied with respect to the product its components and accessories or any obligations liabilities on the part of the Company are hereby expressly excluded The Company neither assumes nor authorizes any third party to assume on its behalf any other liabilities with respect to the sale of this Vermont Castings or Majestic product The warranties as outlined within this document do not apply to chimney components or other non CFM Corporation accessories used in conjunction with the installation of this product Damage to the unit while in transit is not covered by this warranty but is subject to claim against the common carrier Contact the dealer from whom you purchased your fireplace stove do not operate the appliance as this might negate the ability to process the claim with the carrier The Company will not be responsible for a Down drafts or spillage caused by environmental conditions such as near by trees buildings roof tops hills or mountains b Inadequate ventilation or negative air pressure caused by mechanical systems such as furnaces fans clothes dryers etc e This warranty is void if a The fireplace has been op
6. UVDR42C Homeowner s Installation and Operating Manual INSTALLER Leave this manual with the appliance CONSUMER Retain this manual for future reference 20007469 9 07 Rev 5 UVDR Series Unvented Gas Fireplaces Table of Contents Hearth DiMensSioONS ooonncnnnccnccicinncononcncnnncnonnonononononononnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnonnnnnnnnnnnananennnennnnnns 2 Fireplace DIMENSIONS cid inde 3 Installation Instructions cccccncccnnncncccccnnonononononanonnncnnnnnnnnnnnnnnnnnnnnnnnnnnnonononnnnnnnnnanannnennnnnnnns 4 Locating the Fireplace iii tad naci Dalla doo 4 GAS NS OPA CR OO hoe ceeaadeatuusagetslasaten hs tuhemneldstecchean E T E 4 Dra to ico ia conn lla EA AEE 4 CIMA CS ii a aida 4 Installing the FireboX idea ieee ponia airada dial coges oe 5 Finishing the Fireplace ooooocononnnnncococccccoccnncccnnnnnnnnnnnnncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnninnnnnnnnnnnnnnnn 7 Hearth EXtenSio i dai tada 7 Pre wiring of Junction BOX cccecececceeeeeeeeeeeeececeneaeeeeeeeeeeeeeeseececcaaeeseeeeeeeeetessecenenneeeess 7 Electrical Semi ES casi 7 BL 4 Blower InstallatiON ooccccnnnnnononononononononoononcncnnononononnnnnnnnnnnnnnnonononnnnnonanannnnnnnnenons 8 UVDR3IGC Installation cita A cada 8 UVDR42C InstallatiON cccccccccnnccccnoconoonnonnnononnonononnnnnnnnnnnnnnnnnonnnnnnonononnnnnnnanannnnnneneness 8 Install Optional Outside Air Kit sccacicicctcaeois arcada citn nad
7. a eaaa daria dotada 9 Replacement AA 11 ACCESSOMES uranio ce Sods Sedan E Eo aa eeae da nl a e se E a E 12 DOIVICIND siii a Aida 12 Warranty cicirine aan nai Dada 15 Certified To ANSI Z 21 91a 2002 Ventless Fireboxes for use with any ANSI Z21 11 2 Unvented Room Heaters Units UVDR36C GF1VF2 UVDR42C GF1VF4 Front Width Back Width A B UVDR36C 30 23 889 mm 589 mm UVDR42C 40 327 683 mm 559 mm Fig 1 Hearth dimensions 2 20007469 UVDR Series Unvented Gas Fireplaces Fireplace Dimensions Rough _ Opening 1 2 Clearance to l Rough Opening Width C gt Combustibles not Required at this Point Rough Opening Height 1 2 Clear ance to Combustibles not Required at this Point Y Gas Line Access 20007469 UVDR Series Unvented Gas Fireplaces Installation Instructions Locating the Fireplace Figure 2 shows some of the many ways your fireplace may be installed Consider the traffic pattern in your room and the location of doors and windows Moving air from ceiling fans open doors and hot air grilles may cause the flames to soot If a disturbance is found that effects the flames it must be eliminated by turning off the ceiling fan closing the door or closing or moving the hot air register A corner location may be best where space is limited Your fireplace weighs
8. are should be taken not to damage the fan blades or housing Step 2 The SCVS Variable Speed Control Kit or standard wall switch should be installed before the blower assembly installation Please refer to instruc tions found in the SCVS Kit Step 3 Remove the bottom brick from the fireplace and carefully place it to the side to prevent damage Use a flat blade screwdriver to gently lift up the front edge of the brick then pull forward to remove Step 4 Locate the blower access cutout found at the rear of the hearth pan Next remove tape backing from tape on blower housing Center the blower assembly in the access cutout area with the blower outlet duct point ing upward then press firmly to attach foam tape to the back and bottom of the fireplace Fig 10 Step 5 Locate the junction box cutout found on the right side of the hearth pan Route the powercord under the hearth pan and plug it into the receptacle outlet found in the junction box Fig 11 Step 6 Turn power back on and test blower operation Step 7 Replace the bottom brick in the fireplace UVDR42C Blower Installation Step 1 Carefully unpack the blower assembly and familiarize yourself with the parts Care should be taken not to damage the fan blades or housing Step 2 The SCVS Variable Speed Control Kit or standard wall switch should be installed before the blower assembly installation Please refer to instruc tions found in the SCVS Kit Step
9. ation FP1061 Fig 15 Caulk and install duct termination rain cap in place 10 Operating Precautions and Instructions Operation is automatic A slight negative pressure inside the house will open the barometric flapper valve Periodically inspect the duct termination for any block age Correct if necessary 20007469 UVDR Series Unvented Gas Fireplaces CFM Corporation reserves the right to make changes in design materials specifications prices and discontinue colors and products at any time without notice UVDR36 42C Series Unvented Fireplaces Description UVDR36C UVDR42C 1 Firescreen Rod 2 per fireplace 68403 65864 2 Firescreeen w Rings 2 per fireplace 66146 62197 3 Screen Retainer 4 per fireplace 62222 62222 4 Black Canop 68779 69554 5 Back Brick 73535 73395 6 Right Side Brick 73498 7 Left Side Brick 75752 8 Side Brick 2 per fireplace 73394 9 Bottom Brick 73500 10 Bottom Left Brick 79013 11 Bottom Middle Right Left Brick 79014 12 Bottom Right Brick 79015 13 Cover Hearth 78
10. ation should be located so it is exposed to an out of doors opening at least 100 square inches If the duct termination must be located in a crawl space or basement be sure the termination area has 100 square inches of ventilation opening to outside air The duct termination must be located so it does not compete for air flow with exhaust fans gas vent hoods or other air consuming devices or appliances It must not be obstructed by rafters insulation materials or other obstructions The less restrictive the air supply the better the outside air kits will perform It is good practice to protect your hands and eyes during installation by wearing work gloves and safety glasses CAUTION Do not install termination into a garage or other area that could contain flammable liquids or fumes or into an attic space Installation Instructions Determine the location of the fireplace as described in the fireplace installation manual Then plan location of the duct termination and the route of the duct run between the fireplace and the duct termination Duct run must be limited to a maximum distance of 40 12 2m from the fireplace pipe collar to duct termina tion This will provide the least restriction to air flow No more than four 4 90 elbows can be used Duct run may be horizontal vertical inclined or any combina tion of these Fig 12 You are now ready to install the Outside Air Kit 1 Remove the screws retaining the outsi
11. de air cover plate if provided Located on the left side of front open units on backside of multisided units Discard coverplate Fig 13 2 Secure the inlet collar assembly to the outer casing with four screws not provided Fig 14 3 Slide the duct over the collar and attach the duct to the collar using the plastic tie straps or three 3 screws screws not provided Continue attaching the ducting together using three 3 screws at each joint until you have installed sufficient duct to arrive at your duct termination locations 4 At the termination end install the duct termination This should be installed from the outside of the home Cut a hole in the desired location approxi mately 41 114mm in diameter caulk around the hole and slide the termination through the opening from outside the home The termination rain cap 20007469 UVDR Series Unvented Gas Fireplaces should be caulked around its perimeter to assure a tight seal The rain cap opening should be positioned downward Fig 15 The Outside Air Kit is now installed and ready for use Soffit Termination C Duct Termination 40 Max Duct Run Exterior Wall Termination Exterior Wall 40 Max Duct Run Rain Cap Duct Termination FP1060 Fig 12 Typical outside air installations Cover Plate Fig 13 Remove outside air cover plate and discard retain screws UVDR Series Unvented Gas Fireplaces Duct Ter min
12. e Shim if necessary Step 4 Secure the Firebox Four 4 nailing flanges are supplied with the fireplace found on the fireplace hearth To level the box and secure it firmly in place remove the nailing flanges from the hearth and install at the sides of the fireplace as shown in Figure 5 NOTE The nailing flanges have two 2 sets of holes to allow for adjustment for 1 2 or 5 8 offset of the face of the unit When installing the nailing flanges choose the set of holes on the nailing flange that fit with your application UVDR Series Unvented Gas Fireplaces 1 2 Clearance not Required at This Point Side View Nailing Flanges Fig 5 Secure firebox Step 5 Gas Piping and Connection The gas piping must be installed in accordance with local codes or in the absence of local codes in accor dance with the National Fuel Gas Code ANSI Z223 1 NFPA 54 latest edition The normal gas connection is 1 2 NPT made at the left side facing the unit If a right side connection is desired the connecting pipe must be led at the rear of the fire place to terminate at the left hand side for connection to the fireplace Noncombustible Insulation Side Refractory Refractory Cement Fireplace Outer Wrap 1 2 Gas Pipe Fig 6 Gas line installation Piping should be tested for leaks prior to final wall installation Test for leaks using soap and water solution after completing th
13. e cer tain that every installation operation is done correctly Complete the installation steps in the sequence shown LOCAL BUILDING CODES SHOULD BE CONSULTED IN ALL CASES AS TO THE PARTICULAR REQUIRE MENTS CONCERNING THE INSTALLATION OF FAC TORY BUILT FIREPLACES Select the location for the fireplace by taking into con sideration the factors previously outlined in the Locating the Fireplace section of the manual 20007469 UVDR Series Unvented Gas Fireplaces Clearance to Combustible Mantel Projections with 4 Canopy Mantel Combustible Projections 10 Combustible Projections above the fireplace must be within the area described by the dashed line Step 1 Framing the Firebox The width of the framed opening must be 39 for 36 models or 451 for 42 models Fig 4 The entire fireplace can be elevated above the floor to achieve a raised hearth effect This can be done by adding a small platform to achieve the desired height NOTE Refer to Pre wiring the Junction Box and Electri cal Service on Page 7 Step 2 Install the Firebox Install the firebox into the framed opening by setting it directly in front of the opening and sliding it into the proper position Step 3 Level the Firebox Check the level of the firebox on the top edge of the fire place fac
14. e connection DO NOT USE OPEN FLAME Step 6 Optional Procedure For Cold Climate Instal lations The insulation and sealing of the enclosure around the fireplace is very important in cold climates If the en closure is insulated and sealed properly you can avoid future cold air problems The time taken to install the firebox correctly is well worthwhile The following steps are to stop potential cold air problems Insulation of the Fireplace Enclosure When in a chase or an outside wall the fireplace en closure should be insulated like any other wall of your home Insulation should be installed on the outside wall s and the wall above the fireplace Insulate to Seal Under the Fireplace Insulating under the fireplace is beneficial for installa tions on a concrete slab The fireplace should be placed on insulating board It is important that a hard rigid surface be maintained so do not use fiberglass insula tion for this purpose CAUTION WHEN INSTALLING A FIREPLACE IN AN INSULATED ENCLOSURE BE SURE TO MAINTAIN ALL MARKED AIR SPACES Seal Seams Seal the seams of the fireplace where the outer wall meets the bottom pan and the front face Also seal between the fireplace and finishing materials Use high temperature caulk Refer to Figure 7 for details of seal ing spaces between the fireplace and finishing materi als Note the small amount of insulation installed across the top of the fireplace and down the sides as a backing fo
15. erated in atmospheres contaminated by chlorine fluorine or other damaging chemicals b The fireplace has been subjected to prolonged periods of dampness or condensation c Any damages to the fireplace combustion chamber heat exchanger or other components due to water or weather damage which is the result of but not limited to improper chimney venting installation d Any alteration willful abuse accident or misuse of the product has occurred IF WARRANTY SERVICE IS NEEDED 1 Contact your supplier Make sure you have your warranty your sales receipt and the model serial number of your CFM Corporation product 2 DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF NATIONAL We recommend that our gas FIREPLACE INSTITUTE hearth products be installed NFI and serviced by profes sionals who are certified in the U S by the National Fireplace Institute NFI as CERTIFIED NFI Gas Specialists www nficertified org CFM Corporation 410 Admiral Blvd Mississauga Ontario Canada L5T 2N6 800 668 5323 www cfmcorp com
16. for breakage due to misuse or accident Glass doors are not covered for discoloration or burned in stains due to environmental issues or improper cleaning and maintenance BRASS PLATED PARTS AND ACCESSORIES Brass parts should be cleaned with Lemon oil only Brass cleaners cannot be used Mortar mix and masonry cleaners may corrode the brass finish The Company will not be responsible for nor will it warrant any brass parts which are damaged by external chemicals or down draft conditions GAS VALVES Gas valves are covered for a period of one year ELECTRONIC AND MECHANICAL COMPONENTS Electronic and mechanical components of the burner assembly are covered for one year All steel tube burners are warranted for one year ACCESSORIES Unless otherwise noted all components and CFM Corporation company supplied accessories are covered for a period of one year CONDITIONS AND LIMITATIONS e This new Vermont Castings or Majestic product must be installed by a competent authorized service contractor A licensed technician as prescribed by the local jurisdiction must perform any installation service work It must be installed and operated at all times in accordance with the Installation and Operating instructions furnished with the product Any alteration willful abuse accident or misuse of the product shall nullify this warranty e This warranty is non transferable and is made to the original owner provided that the purchase was made thro
17. he Company warrants that your new Vermont Castings or Majestic Gas Fireplace Stove is free from manufacturing and material defects for a period of one year from the date of purchase subject to the following conditions and limitations EXTENDED LIFETIME WARRANTY The heat exchanger where applicable and combustion chamber of every Vermont Castings or Majestic gas product is warranted for life against through wall perforation All appliances equipped with an Insta Flame Ceramic Burner have limited lifetime coverage on the ceramic burner plaque Warrantees are made to the original owner subject to proof of purchase and the conditions and limitations listed on this Warranty Document COMPONENT WARRANTY CAST IRON All external and internal cast iron parts are warranted for a period of three years Note On porcelain enamel finished external parts and accessories The Company offers no Warranty on chipping of enamel surfaces Inspect all product prior to accepting it for any damage to the enamel The salt air environment of coastal areas or a high humidity environment can be corrosive to the porcelain enamel finish These conditions can cause rusting of the cast iron beneath the porcelain enamel finish which will cause the finish to flake off Dye lot variations with replacement parts and or accessories can occur and are not covered by warranty GLASS DOORS Glass doors are covered for a period of one year Glass doors are not warranted
18. n order to reduce mantel heights as shown in Figure 3d If the canopy is installed a combustible mantel piece may project 2 from the wall at 61 2 above the fireplace opening A 6 mantel projection at 13 above the fireplace opening and a 10 projec tion at 22 above the opening Fig 3a and 3d To install the optional canopy remove the four 4 screws supplied with a Phillips screwdriver Two 2 20007469 Clearance to Combustible Mantel Projections without N N os MN o Oo Combustible Per pendicular Wall o 3b i oe D R Clearances without Canopy Clearance from Top of Fireplace Opening Noncombustible Material Fireplace Opening FP604b Fig 3 Clearances to combustibles screws are located across the top of the fireplace opening approximately 5 to the right and left from center Two 2 screws are located 4 down from the top on each side of the fireplace opening Place the canopy making sure the 1 4 hex head screws across the top of the opening align with the clear ance holes in the canopy Secure with the four 4 previously removed screws WARNING The firebox canopy must not be modified or replaced with a canopy that may be provided with the unvented decorative room heater 4 Floor Clearances No clearance is required if the appliance is installed per these instructions Installing the Firebox This list of specific instructions will help you mak
19. no more than some of your fine furniture If the fireplace is located near a load bear ing wall additional supports to the foundation will not be necessary HEAVY FACINGS SUCH AS BRICK STONE ETC MAY REQUIRE ADDITIONAL FOUNDA TION SUPPORT ALTHOUGH THIS UNIT MAY BE INSTALLED ON COMBUSTIBLE SURFACES IT MUST NOT BE IN STALLED ON CARPET OR VINYL Room Divider Partial Room Projection Full Room Projection Flush Fig 2 Locating the fireplace Gas Line The gas line must be installed before framing in the fire place by a licensed gas line installer Do not locate the fireplace in high traffic areas or areas exposed to high drafts and winds Locate the fireplace away from furniture and draperies Fireplace Clearances The fireplace may be placed directly on a combustible floor against a combustible wall at marked clearances or on a raised wooden platform S If the fireplace is to be installed on a raised wooden platform the platform must be a continuous level sur face The fireplace must be secured in place so it can not shift positions The nailing flanges on the sides of the firebox make securing it to the framing easy They were designed to allow the installation of 1 2 wallboard or plywood flush with the face of the fireplace Only the header Fig 1 may rest on the standoffs on top of the firebox When the fireplace is installed over carpeting vinyl tile or any combustible material
20. ordance with CSA Standard C22 1 Canadian Electrical Code part 1 or with the National Electrical Code ANSI NFPA 70 latest edition and or in accordance with local codes CAUTION Should this blower require servicing the power supply must be disconnected 120 Volt A Firebox Acces G sory Junction Box Fig 9 Blower wiring diagram UVDR Series Unvented Gas Fireplaces Blower Installation BEFORE YOU BEGIN A FEW BASIC RULES 1 Check to ensure that electrical service has been provided to the junction box located in the bottom chamber of the firebox 2 Check local building codes before installation of the firebox and the blower kit 3 All wiring must be installed and or inspected as necessary to comply with the local authority having jurisdiction 4 The circuit breaker controlling the power supply to the pre wired junction box in the appliance must be in the OFF position before beginning installation of the blower 5 The appliance when installed must be electrically grounded in accordance with local codes or in the absence of local codes with the National Electri cal Code ANSI NFPA 70 or the Canadian Electrical Code CSA C22 1 Read all the installation instructions for the appli cable appliance before beginning the installation of the blower UVDR36C Blower Installation Step 1 Carefully unpack the blower assembly and familiarize yourself with the parts C
21. r the caulk 20007469 Finishing Material Stud Noncombustible Material Caulking or Sealant Insulation Side View Noncombustible Insulation Finishing Material an or Sealant Top View Fig 7 Sealing spaces between fireplace and finishing materi als Finishing the Fireplace There are a wide variety of finishing materials avail able for your fireplace from formal wall treatments with marble and mantels to rustic wood paneling stone or brick IT IS IMPORTANT THAT THE BLACK FACE OF THE FIREPLACE NOT BE COVERED WITH ANY TYPE OF COMBUSTIBLE MATERIAL Noncombustible facing materials such as marble brick or ceramic tile may overlap the black face of the fire place up to the opening on either side of the fireplace Seal all joints between the black fireplace face and the wall covering with a heat resistant material such as rock wool insulation or mortar Be sure to use high tempera ture adhesive or mortar when anchoring brick stone or tile to the face of the fireplace Check to see whether man made brick and stone are made of noncombustible materials before using them on the face of the fireplace Some of these products contain combustible materials Combustible wall coverings such as paneling or wall board may not overlap the black face of the fireplace The space between the wall covering and the fireplace should be sealed with a heat resistant material such as rock wool insulation or mortar NOTE An L
22. shaped steel lintel must be installed across the top of the firebox opening where facing materials such as brick or stone are used on the face of the firebox It acts as a support firestop It should be attached to the face of the fireplace with screws and sealed to the fireplace with a heat resistant sealer WARNING The firebox screens must be in place be fore operating the fireplace WARNING These vent free fireplaces are not to be used with glass doors 20007469 UVDR Series Unvented Gas Fireplaces Hearth Extension A hearth extension may be used but is not required for these fireboxes A raised hearth extension may be used as shown in Figure 8 Seal with Noncom Hearth Brick bustible Material Hearth _ 12 da Combustibles Al lowed J no carpet or vinyl Combustible Plateform SH Fig 8 Araised hearth extension Surround Pre Wiring of Junction Box Wiring should be connected at the junction box located on the right side of the firebox prior to the installation of the blower kit A standard wall box should be used to contain the SCVS Variable Speed Control Kit Electrical Services If an electrical supply of 120V is being roughed in to the fireplace junction box to provide for future installation of optional blower kit the wiring should be connected to the junction box located on the right side of the firebox NOTE All electric connections are to be made in ac c
23. ugh an authorized supplier of the Company e The customer must pay for any Authorized Dealer in home travel fees or service charges for in home repair work It is the dealers option whether the repair work will be done in the customer s home or in the dealer s shop e If upon inspection the damage is found to be the fault of the manufacturer repairs will be authorized at no charge to the customer parts and or labor e Any part and or component replaced under the provisions of this warranty is covered for six months or the remainder of the original warranty whichever is longest This warranty is limited to the repair of or replacement of part s found to be defective in material or workmanship provided that such part s have been subjected to normal conditions of use and service after said defect is confirmed by the Company s inspection The company may at its discretion fully discharge all obligations with respect to this warranty by refunding the wholesale price of the defective part s Any installation labor construction transportation or other related costs expenses arising from defective part s repair replacement or otherwise of same will not be covered by this warranty nor shall the Company assume responsibility for same Further the Company will not be responsible for any incidental indirect or consequential damages except as provided by law SOME STATES DO NOT ALLOW FOR THE EXCLUSION OR LIMITATION
Download Pdf Manuals
Related Search