Canon 6226B002 All in One Printer User Manual
Contents
1. PIXMA MG6300 series Setup Guide Setup Guide This guide provides information for setting up a network connection for the printer Network Connection Wireless Connection Preparation for Connection Printer Setup Setup Procedure Selection Push Button Method Standard setup WPS Other setup Advanced setup Disable WEP WPA WPA2 Wired Connection Preparation for Connection Cable Connection Printer Setup Character Entry Troubleshooting Network Connection Wireless Connection Preparation for Connection Before Starting Wireless Connection Setup 1 Make sure that the printer is turned on If the power is on the POWER lamp A will be lit Notes on Wireless Connection e Make sure that the computer is connected to the access point A or wireless network router you want to connect your printer to e The configuration router functions setup procedures and security settings of the network device vary depending on your system environment For details refer to the manual of your network device or contact its manufacturer e Check if your device supports IEEE802 11n 802 11g or 802 11b e f your device is set to the IEEE802 11 n only mode WEP or TKIP cannot be used as a security protocol Change the security protocol for your device to something other than WEP and TKIP or change the setting to something other than IEEE802 11 n only e For office use consult your network administrator e Ta2. hexadecimal created automatically on the access point then enter it on the printer e For details on how to check the specifications of the access point refer to the manual supplied with the access point or contact its manufacturer Mi WLAN setting list If the MAC address filtering is enabled on the access point change settings so that the MAC address of the printer will be accepted Follow the procedure below to check the MAC address of the printer 1 Touch the HOME button 2 Tap Setup 3 Tap Device settings 4 Tap LAN settings gt Confirm LAN settings gt WLAN setting list to check MAC address MAC address Inactive Pre shared bey For details on how to change the settings of the access point refer to the manual supplied with the access point or contact its manufacturer Mi To perform Standard setup again 1 Touch the HOME button A Standard etum 2 Flick the screen left or right then tap the WLAN setup icon E WPA WPA2 fi Failed to connect to the access point Make sure that the passphrase entered for the access point is correct ried to connect to the access port Follow the steps below 1 Cheek that the selected AOCeSS point E cComect OF If the problem is not resolved there may be other causes See also the sections below e If the DHCP function of the access point is inactive enable the DHCP function and configure wireless connection settings again e For details on how
3. multiple access points The message appears when multiple access points with the same name are found Mulliplt access pois wih the same name exist Do You warmt to use multiple access points Use one AccessPoint only Use multiple AccessPoints When you have only one access point Select Use one AccessPoint only then tap OK Select the MAC address of the target access point on the displayed screen Multiple access pois wih the same name exist Do You want to wuse multiple Access points Use one AccessPoint only AMER EE A EE A E E Use multiple AccessPoirts For details on how to check the MAC address of the access point refer to the manual supplied with the access point or contact its manufacturer When using multiple access points Tap Use multiple AccessPoints Multip access pons wih the same name exist Do you want to use multiple Access points Use one AccessPoint only Use multiple AccessPoints Mi An Unknown Access Point is Displayed Access points in use nearby may also be detected I The Access Point Name is Not Displayed Properly Access point names with double byte characters are not displayed properly However they can be selected I The Access Point Name is Not Displayed Automatically Refer to the manual supplied with the access point or contact its manufacturer E WEP fH Failed to connect to the access point Make sure that the WEP key entered for the access point is correct In a
4. point name network name and network password of your access point or router e Are the computer and network device configured e Are the access point and printer installed in an open space where wireless communications are possible e Is the access point operating in IEEE802 11n 2 4 GHz IEEE802 11g or IEEE802 11b After checking the above points tap Search again on the printer to search for the access point again If the problem is not resolved there may be other causes See also the sections below e If SSID broadcast connection via ANY SSID etc is disabled or the stealth mode is enabled on the access point enable SSID broadcast connection via ANY SSID etc or disable the stealth mode then tap Search again on the printer to search for the access point again e Select Directly enter the access point name in the Select access point screen Wireless connection settings of the access point can be entered on the printer directly e If WPA WPAZ2 Enterprise is set as the security protocol encryption standard on the access point change the security protocol encryption standard and configure wireless connection settings again WWPA WPA2 Enterprise is not supported on this printer e For details on how to change the security protocol encryption standard for the access point refer to the manual supplied with the access point or contact its manufacturer Multiple access points with the same name exist Do you want to use
5. to check or change the settings of the access point refer to the manual supplied with the access point or contact its manufacturer Mi WLAN setting list If the MAC address filtering is enabled on the access point change settings so that the MAC address of the printer will be accepted Follow the procedure below to check the MAC address of the printer 1 Touch the HOME button 2 Tap Setup 3 Tap Device settings 4 Tap LAN settings gt Confirm LAN settings gt WLAN setting list to check MAC address MAC address Inactive Pre shared key For details on how to change the settings of the access point refer to the manual supplied with the access point or contact its manufacturer If the problem is not resolved there may be other causes See also the sections below e If the access point is configured to communicate using IEEE802 11n standard only and encryption is set to TKIP change the encryption to something other than TKIP or change the communication standard to something other than IEEE802 11n then configure wireless connection settings again e If encryption is set to TKIP IEEE802 11n cannot be used as the communication standard e For details on how to change the settings of the access point refer to the manual supplied with the access point or contact its manufacturer I To perform Standard setup again 1 Touch the HOME button A Standard etun WPS Oiher setup 2 Flick the screen left or rig
6. types Tap to insert a space Tap to delete the character at the cursor Use EE or Q to move the cursor to the target character 2 Tap the character you want to enter 3 Repeat 1 and 2 to enter the remaining characters Troubleshooting Standard setup Mi The Target Access Point is Not Detected e Is the network device router etc turned on If the network device is already turned on turn it off then turn it back on e Check the access point name network name and network password of your access point or router e Are the computer and network device configured e Are the access point and printer installed in an open space where wireless communications are possible e Is the access point operating in IEEE802 11n 2 4 GHz IEEE802 11g or IEEE802 11b After checking the above points tap Search again on the printer to search for the access point again If the problem is not resolved there may be other causes See also the sections below e If SSID broadcast connection via ANY SSID etc is disabled or the stealth mode is enabled on the access point enable SSID broadcast connection via ANY SSID etc or disable the stealth mode then tap Search again on the printer to search for the access point again e Select Directly enter the access point name in the Select access point screen Wireless connection settings of the access point can be entered on the printer directly e If WPA WPAZ2 Enterprise is set as the se
7. Entering the Access Point s Settings Directly on the Printer When using WEP key number 2 3 or 4 select Advanced setup O A Push Button Method Connection Using WPS 1 Press and hold the WPS button on the access point For details on pressing the WPS button refer to the access point manual To start setup tap Start setup on the device Start setup To other connection methods 2 Tap Start setup on the printer within 2 minutes The blue Wi Fi lamp on the printer flashes while searching for or connecting to the access point 3 When the left screen appears tap OK Connected to the access point WLAN Advanced Web setup print service The network connection setup is now complete B Standard setup Connection via Standard setup 1 Tap Standard setup Standard setup WPS Other setup 2 Tap your access point Search again 3 One of the screens below will be displayed on the printer 8 64 characters 5 26 characters Please enter Please enter 4 Tap the screen 5 Enter the network password WEP key or passphrase Character entry is case sensitive 6 Tap Apply 7 Make sure that the network password is correct Character entry is case sensitive 8 Tap OK 9 When the left screen appears tap OK Connected to the access point WLAN Advanced Web setup print service The network connection setup is now complete Cc WPS Connecti
8. I The Access Point Name is Not Displayed Properly Access point names with double byte characters are not displayed properly However they can be selected I The Access Point Name is Not Displayed Automatically Refer to the manual supplied with the access point or contact its manufacturer W The Network Password is Not Displayed Automatically Refer to the manual supplied with the access point or contact its manufacturer E WEP fH Failed to connect to the access point Make sure that the WEP key entered for the access point is correct In addition when using WEP key number 2 3 or 4 of the access point set to use WEP key number 1 or select a WEP key number by entering wireless connection settings of the printer directly Faded to connect to the access port Follow the steps below 1 Cheek ihat the selected JOLE point E cComect Of For details on how to change the WEP key number of the access point refer to the manual supplied with the access point or contact its manufacturer If the problem is not resolved there may be other causes See also the sections below e If the DHCP function of the access point is inactive enable the DHCP function and configure wireless connection settings again e For details on how to check or change the settings of the access point refer to the manual supplied with the access point or contact its manufacturer e If using an access point that automatically creates WEP keys check the WEP key
9. WEP key is correct 10 Tap OK 11 When the left screen appears tap OK Connected to the access point WLAN Advanced Web setup print service The network connection setup is now complete E WPA WPA2 5 Tap the screen Please enter 6 Enter the passphrase Character entry is case sensitive 7 Tap Apply 8 Make sure that the passphrase Is correct 9 Tap OK 10 When the left screen appears tap OK Connected to the access point a oO WLAN Advanced Web setup print service The network connection setup is now complete Wired Connection Preparation for Connection Before Starting Wired Connection Setup 1 Make sure that the printer is turned on If the power is on the POWER lamp A will be lit A Notes on Wired Connection e Make sure that the computer and router A or access point are connected we The configuration router functions setup procedures and security settings of the network device vary depending on your system environment For details refer to the manual of your network device or contact its manufacturer For office use consult your network administrator Take added care when connecting to a network that is not protected with security measures as there is a risk of disclosing data such as your personal information to a third party This printer cannot be used over wireless and wired connections at the same time e When using a router connect
10. curity protocol encryption standard on the access point change the security protocol encryption standard and configure wireless connection settings again WWPA WPA2 Enterprise is not supported on this printer e For details on how to change the security protocol encryption standard for the access point refer to the manual supplied with the access point or contact its manufacturer Multiple access points with the same name exist Do you want to use multiple access points The message appears when multiple access points with the same name are found Mulipkt access points wih The same name exist Do you want to use multiple access points Use one AccessPomt only Use multiple AccessPoints When you have only one access point Select Use one AccessPoint only then tap OK Select the MAC address of the target access point on the displayed screen Mulipkt access points wih Access points PA ee ie oe i E Use one AccessPomt only AMER Re Use multiple AccessPoints For details on how to check the MAC address of the access point refer to the manual supplied with the access point or contact its manufacturer When using multiple access points Tap Use multiple AccessPoints Mullip access poms wih the same name exist Do you want ta use multiple Access points Use one AccessPoint only Use multiple AccessFoints Mi An Unknown Access Point is Displayed Access points in use nearby may also be detected
11. ddition when using WEP key number 2 3 or 4 of the access point set to use WEP key number 1 or select a WEP key number by entering wireless connection settings of the printer directly ried to conmect to the access port Follow the steps below 1 Cheek that the selected JOLE point E cComect Of For details on how to change the WEP key number of the access point refer to the manual supplied with the access point or contact its manufacturer If the problem is not resolved there may be other causes See also the sections below e If the DHCP function of the access point is inactive enable the DHCP function and configure wireless connection settings again e For details on how to check or change the settings of the access point refer to the manual supplied with the access point or contact its manufacturer e If using an access point that automatically creates WEP keys check the WEP key hexadecimal created automatically on the access point then enter it on the printer e For details on how to check the specifications of the access point refer to the manual supplied with the access point or contact its manufacturer Mi WLAN setting list If the MAC address filtering is enabled on the access point change settings so that the MAC address of the printer will be accepted Follow the procedure below to check the MAC address of the printer 1 Touch the HOME button 2 Tap Setup 3 Tap Device settings 4 Tap LAN settin
12. gain 1 Touch the HOME button A Standard setum 2 Flick the screen left or right then tap the WLAN setup icon E WPA WPA2 fi Failed to connect to the access point Make sure that the passphrase entered for the access point is correct ried to connect to the access port Follow the steps below 1 Cheek that the selected AOCeSS point E cComect OF If the problem is not resolved there may be other causes See also the sections below e If the DHCP function of the access point is inactive enable the DHCP function and configure wireless connection settings again e For details on how to check or change the settings of the access point refer to the manual supplied with the access point or contact its manufacturer Mi WLAN setting list If the MAC address filtering is enabled on the access point change settings so that the MAC address of the printer will be accepted Follow the procedure below to check the MAC address of the printer 1 Touch the HOME button 2 Tap Setup 3 Tap Device settings 4 Tap LAN settings gt Confirm LAN settings gt WLAN setting list to check MAC address MAC address Inactive Pre shared key For details on how to change the settings of the access point refer to the manual supplied with the access point or contact its manufacturer If the problem is not resolved there may be other causes See also the sections below e If the access point is configured to commu
13. gs gt Confirm LAN settings gt WLAN setting list to check MAC address MAC address Inactive Pre shared bey For details on how to change the settings of the access point refer to the manual supplied with the access point or contact its manufacturer Select Directly enter the access point name in the Select access point screen Wireless connection settings of the access point can be entered on the printer directly Mi The WEP Key is Not Displayed Automatically Refer to the manual supplied with the access point or contact its manufacturer I The device may not be able to connect to the network in the following cases If the DHCP function of the access point is inactive enable the DHCP function or specify the IP address IPv4 only of the printer and configure wireless connection settings again In addition make sure that the selected WEP key number and entered WEP key are correct For details on how to check or change the settings of the access point refer to the manual supplied with the access point or contact its manufacturer To specify the IP address of the printer follow the procedure below Tap Setup in the HOME screen Tap Device settings Tap LAN settings Tap Other setup Tap TCP IP settings Tap IPv4 Tap Yes Tap IP address Tap Manual setup Follow the on screen instructions to proceed with settings When the setup is complete touch the HOME button Sea oS SYS HM To perform Advanced setup a
14. ht then tap the WLAN setup icon WPS Mi Cannot connect Connections are being attempted from multiple access points simultaneously The screen appears when connections are being attempted from multiple access points simultaneously Wait for a while then configure WPS settings again Press the WPS button on only one access point Canal connect Connections are being attempted from MuUTPe access points simultaneously Folow the steps below Of Mi Failed to connect The screen appears when an error occurs Check the access point settings then configure WPS settings again Faded t cormhect Follow the steps below 1 Restart the access point 2 Try connecting again 3 See the access point manual and check the settimgs For details on how to check the settings of the access point refer to the manual supplied with the access point or contact its manufacturer W Timeout error The screen appears when WPS setup was not completed within a specified time e Is the network device router etc turned on If the network device is already turned on turn it off then turn it back on Tmedut error Follow the steps below 1 fede the wireless LAN setup nowhich you press and hold the WPS button Advanced setup Mi The Target Access Point is Not Detected e Is the network device router etc turned on If the network device is already turned on turn it off then turn it back on e Check the access
15. ke added care when connecting to a network that is not protected with security measures as there is a risk of disclosing data such as your personal information to a third party e This printer cannot be used over wireless and wired connections at the same time e An Ad hoc connection which establishes a direct connection to the computer over a wireless connection without an access point is not supported Be sure to prepare an access point Printer Setup 1 If the HOME button A on the printer is lit touch the HOME button 2 Flick the screen left or right then tap the WLAN setup icon w A ip gt a4 The blue Wi Fi lamp A lights up when wireless connection is enabled Setup Procedure Selection The printer will automatically search for access points supporting WPS Wi Fi Protected Setup If the Push Button Method screen is displayed on the printer When you are unsure if your access point or router supports this technology tap To other connection methods Proceed to the screen for Standard setup To start setup tap Start setup on the device z Standard setup WPS Other setup Start setup Push Button Method gt A Select the most suitable connection method from the following e Standard setup B Connect to Access Point by entering the Network Password e WPS O C Connect to WPS compatible Access Point e Other setup Advanced setup D Connecting to the Network by
16. nicate using IEEE802 11n standard only and TKIP is set as the encryption standard change the encryption standard to something other than TKIP or change the communication standard to something other than IEEE802 11n then configure wireless connection settings again If the encryption standard is set to TKIP IEEE802 11n cannot be used as the communication standard e For details on how to change the settings of the access point refer to the manual supplied with the access point or contact its manufacturer W The Passphrase is Not Displayed Automatically Refer to the manual supplied with the access point or contact its manufacturer HM To perform Advanced setup again 1 Touch the HOME button A Standard etun WPS Oiher setup 2 Flick the screen left or right then tap the WLAN setup icon
17. on Using WPS 1 Tap WPS Standard setup WPS Other setup 2 Tap Push button method Push button method olny PIN code method Connect to an access point supporting the WPS push button method 4 Press and hold the WPS button on the access point For details on pressing the WPS button refer to the access point manual Press and hold the WPS button on the access point then tap OK on the device 5 Tap OK on the printer within 2 minutes The blue Wi Fi lamp on the printer flashes while searching for or connecting to the access point 6 When the left screen appears tap OK Connected to the access point WLAN Advanced Web setup print service The network connection setup is now complete D Other setup Advanced setup Connection via Advanced setup 1 Tap Other setup Standard setup WPS Other setup 2 Tap Advanced setup Advanced setup 3 Tap your access point Search again 4 Tap the security protocol used by the access point WEP WPA PSK TKIP WPA PSK AES Mi Disable 5 When the left screen appears tap OK Connected to the access point P mR WLAN Advanced Web setup print service The network connection setup is now complete E WEP 5 Tap the WEP key number you want to use 6 Tap the screen Please enter 7 Enter the WEP key Character entry is case sensitive 8 Tap Apply 9 Make sure that the
18. the printer and computer to the LAN side same network segment Cable Connection You will need an Ethernet cable sold separately 1 2 Connect the printer and a network device router etc with an Ethernet cable A Please make sure to use the correct port on the back of the printer Do not connect it to the USB port Printer Setup 1 If the HOME button A on the printer is lit touch the HOME button ECO Quiet settings setting Maintenance Clean or adjust th evice ECO Device settings Perform various ECO tup settings settings 4 Tap LAN settings Print settings LAN settings Device user settings PictBridge print settings 5 Tap Change wireless wired LAN settina Change wireless wired Wireless LAN setup Confirm LAN settings Other settings Reset LAN settings 6 Tap Wired LAN active Wireless LAN active Wired LAN active Disable LAN 7 Touch the HOME button The network connection setup is now complete Character Entry You can enter the characters when the keyboard is displayed on the printer Follow the procedure below 1 You can enter the characters when the keyboard is displayed on the printer s LCD Password entry is case sensitive Tap to switch between lower case letters and numbers and symbols gt While letters of the alphabet appear tap to switch between upper and lower case letters While numbers and symbols appear tap to switch symbol
Download Pdf Manuals
Related Search